ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 ADC0808/ADC0809 8-Bit P Compatible A/D Converters with 8-Channel Multiplexer Check for Samples: ADC0808-N, ADC0809-N FEATURES DESCRIPTION * * The ADC0808, ADC0809 data acquisition component is a monolithic CMOS device with an 8-bit analog-todigital converter, 8-channel multiplexer and microprocessor compatible control logic. The 8-bit A/D converter uses successive approximation as the conversion technique. The converter features a high impedance chopper stabilized comparator, a 256R voltage divider with analog switch tree and a successive approximation register. The 8-channel multiplexer can directly access any of 8-single-ended analog signals. 1 2 * * * * * * Easy Interface to All Microprocessors Operates Ratiometrically or with 5 VDC or Analog Span Adjusted Voltage Reference No Zero or Full-Scale Adjust Required 8-Channel Multiplexer with Address Logic 0V to VCC Input Range Outputs meet TTL Voltage Level Specifications ADC0808 Equivalent to MM74C949 ADC0809 Equivalent to MM74C949-1 KEY SPECIFICATIONS * * * * * Resolution: 8 Bits Total Unadjusted Error: 1/2 LSB and 1 LSB Single Supply: 5 VDC Low Power: 15 mW Conversion Time: 100 s The device eliminates the need for external zero and full-scale adjustments. Easy interfacing to microprocessors is provided by the latched and decoded multiplexer address inputs and latched TTL TRI-STATE outputs. The design of the ADC0808, ADC0809 has been optimized by incorporating the most desirable aspects of several A/D conversion techniques. The ADC0808, ADC0809 offers high speed, high accuracy, minimal temperature dependence, excellent long-term accuracy and repeatability, and consumes minimal power. These features make this device ideally suited to applications from process and machine control to consumer and automotive applications. For 16channel multiplexer with common output (sample/hold port) see ADC0816 data sheet. (See AN-247 (Literature Number SNOA595) for more information.) Block Diagram Connection Diagrams 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 Figure 1. PDIP Package See Package N0028E www.ti.com Figure 2. PLCC Package See Package FN0028A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage (VCC) (4) 6.5V -0.3V to (VCC+0.3V) Voltage at Any Pin Except Control Inputs -0.3V to +15V Voltage at Control Inputs (START, OE, CLOCK, ALE, ADD A, ADD B, ADD C) -65C to +150C Storage Temperature Range Package Dissipation at TA=25C 875 mW Lead Temp. (Soldering, 10 seconds) PDIP Package (plastic) PLCC Package ESD Susceptibility (1) (2) (3) (4) (5) 260C Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C (5) 400V Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. All voltages are measured with respect to GND, unless otherwise specified. If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications. A Zener diode exists, internally, from VCC to GND and has a typical breakdown voltage of 7 VDC. Human body model, 100 pF discharged through a 1.5 k resistor. Operating Conditions (1) (2) TMINTATMAX Temperature Range -40CTA+85C Range of VCC (1) (2) 4.5 VDC to 6.0 VDC Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. All voltages are measured with respect to GND, unless otherwise specified. Electrical Characteristics - Converter Specifications Converter Specifications: VCC=5 VDC=VREF+, VREF(-)=GND, TMINTATMAX and fCLK=640 kHz unless otherwise stated. Symbol Parameter ADC0808 Total Unadjusted Error (1) (1) 2 Conditions Min Typ Max Units 25C 1/2 LSB TMIN to TMAX 3/4 LSB Total unadjusted error includes offset, full-scale, linearity, and multiplexer errors. See Figure 5. None of these A/Ds requires a zero or full-scale adjust. However, if an all zero code is desired for an analog input other than 0.0V, or if a narrow full-scale span exists (for example: 0.5V to 4.5V full-scale) the reference voltages can be adjusted to achieve this. See Figure 15. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 Electrical Characteristics - Converter Specifications (continued) Converter Specifications: VCC=5 VDC=VREF+, VREF(-)=GND, TMINTATMAX and fCLK=640 kHz unless otherwise stated. Symbol Parameter Conditions ADC0809 Total Unadjusted Error (1) VREF(+) Max Units 0C to 70C 1 LSB TMIN to TMAX 11/4 LSB VCC + 0.1 VDC VCC VCC + 0.1 V (VCC/2) - 0.1 VCC/2 (VCC/2) + 0.1 V -0.1 0 -2 0.5 Input Resistance From Ref(+) to Ref(-) Analog Input Voltage Range See Voltage, Top of Ladder Measured at Ref(+) (2) V(+) or V(-) Voltage, Center of Ladder VREF(-) Voltage, Bottom of Ladder IIN fc=640 kHz, Typ 1.0 2.5 GND - 0.1 Measured at Ref(-) Comparator Input Current (2) Min (3) k V A 2 Two on-chip diodes are tied to each analog input which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the VCCn supply. The spec allows 100 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more than 100 mV, the output code will be correct. To achieve an absolute 0VDC to 5VDC input voltage range will therefore require a minimum supply voltage of 4.900 VDC over temperature variations, initial tolerance and loading. Comparator input current is a bias current into or out of the chopper stabilized comparator. The bias current varies directly with clock frequency and has little temperature dependence (Figure 8). See ANALOG COMPARATOR INPUTS (3) Electrical Characteristics - Digital Levels and DC Specifications Digital Levels and DC Specifications: ADC0808CCN, ADC0808CCV, ADC0809CCN and ADC0809CCV, 4.75VCC5.25V, -40CTA+85C unless otherwise noted Symbol Parameter Conditions Min Typ Max Units 10 200 nA 1.0 A ANALOG MULTIPLEXER VCC=5V, VIN=5V, IOFF(+) OFF Channel Leakage Current TA=25C TMIN to TMAX VCC=5V, VIN=0, IOFF(-) OFF Channel Leakage Current TA=25C -200 -10 TMIN to TMAX -1.0 A (VCC - 1.5) V nA CONTROL INPUTS VIN(1) Logical "1" Input Voltage VIN(0) Logical "0" Input Voltage IIN(1) Logical "1" Input Current (The Control Inputs) VIN=15V IIN(0) Logical "0" Input Current (The Control Inputs) VIN=0 ICC Supply Current fCLK=640 kHz 1.5 V 1.0 A -1.0 A 0.3 3.0 mA DATA OUTPUTS AND EOC (INTERRUPT) VOUT(1) Logical "1" Output Voltage VCC = 4.75V IOUT = -360A IOUT = -10A VOUT(0) Logical "0" Output Voltage IO=1.6 mA 0.45 VOUT(0) Logical "0" Output Voltage EOC IO=1.2 mA 0.45 V 3 A IOUT 2.4 4.5 V V VO=5V TRI-STATE Output Current -3 VO=0 V A Electrical Characteristics - Timing Specifications Timing Specifications VCC=VREF(+)=5V, VREF(-)=GND, tr=tf=20 ns and TA=25C unless otherwise noted. Symbol tSTCLK Parameter Conditions Start Time Delay from Clock (Figure 7) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N MIn 300 Typ Max Units 900 ns Submit Documentation Feedback 3 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com Electrical Characteristics - Timing Specifications (continued) Timing Specifications VCC=VREF(+)=5V, VREF(-)=GND, tr=tf=20 ns and TA=25C unless otherwise noted. Symbol Parameter Conditions MIn Typ Max Units tWS Minimum Start Pulse Width (Figure 7) 100 200 ns tWALE Minimum ALE Pulse Width (Figure 7) 100 200 ns ts Minimum Address Set-Up Time (Figure 7) 25 50 ns tH Minimum Address Hold Time (Figure 7) 25 50 ns tD Analog MUX Delay Time From ALE RS=0 (Figure 7) 1 2.5 s tH1, tH0 OE Control to Q Logic State CL=50 pF, RL=10k (Figure 10) 125 250 ns t1H, t0H OE Control to Hi-Z CL=10 pF, RL=10k (Figure 10) 125 250 ns tc Conversion Time fc Clock Frequency tEOC EOC Delay Time (Figure 7) CIN Input Capacitance At Control Inputs COUT TRI-STATE Output Capacitance At TRI-STATE Outputs (1) 4 fc=640 kHz, (Figure 7) (1) 90 100 116 s 10 640 1280 kHz 8 + 2 S Clock Periods 10 15 pF 10 15 pF 0 The outputs of the data register are updated one clock cycle before the rising edge of EOC. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 Functional Description MULTIPLEXER The device contains an 8-channel single-ended analog signal multiplexer. A particular input channel is selected by using the address decoder. Table 1 shows the input states for the address lines to select any channel. The address is latched into the decoder on the low-to-high transition of the address latch enable signal. Table 1. Analog Channel Selection ADDRESS LINE SELECTED ANALOG CHANNEL C B IN0 L L L IN1 L L H IN2 L H L IN3 L H H IN4 H L L IN5 H L H IN6 H H L IN7 H H H A CONVERTER CHARACTERISTICS The Converter The heart of this single chip data acquisition system is its 8-bit analog-to-digital converter. The converter is designed to give fast, accurate, and repeatable conversions over a wide range of temperatures. The converter is partitioned into 3 major sections: the 256R ladder network, the successive approximation register, and the comparator. The converter's digital outputs are positive true. The 256R ladder network approach (Figure 3) was chosen over the conventional R/2R ladder because of its inherent monotonicity, which ensures no missing digital codes. Monotonicity is particularly important in closed loop feedback control systems. A non-monotonic relationship can cause oscillations that will be catastrophic for the system. Additionally, the 256R network does not cause load variations on the reference voltage. The bottom resistor and the top resistor of the ladder network in Figure 3 are not the same value as the remainder of the network. The difference in these resistors causes the output characteristic to be symmetrical with the zero and full-scale points of the transfer curve. The first output transition occurs when the analog signal has reached +1/2 LSB and succeeding output transitions occur every 1 LSB later up to full-scale. The successive approximation register (SAR) performs 8 iterations to approximate the input voltage. For any SAR type converter, n-iterations are required for an n-bit converter. Figure 4 shows a typical example of a 3-bit converter. In the ADC0808, ADC0809, the approximation technique is extended to 8 bits using the 256R network. The A/D converter's successive approximation register (SAR) is reset on the positive edge of the start conversion start pulse. The conversion is begun on the falling edge of the start conversion pulse. A conversion in process will be interrupted by receipt of a new start conversion pulse. Continuous conversion may be accomplished by tying the end-of-conversion (EOC) output to the SC input. If used in this mode, an external start conversion pulse should be applied after power up. End-of-conversion will go low between 0 and 8 clock pulses after the rising edge of start conversion. The most important section of the A/D converter is the comparator. It is this section which is responsible for the ultimate accuracy of the entire converter. It is also the comparator drift which has the greatest influence on the repeatability of the device. A chopper-stabilized comparator provides the most effective method of satisfying all the converter requirements. The chopper-stabilized comparator converts the DC input signal into an AC signal. This signal is then fed through a high gain AC amplifier and has the DC level restored. This technique limits the drift component of the amplifier since the drift is a DC component which is not passed by the AC amplifier. This makes the entire A/D converter extremely insensitive to temperature, long term drift and input offset errors. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N Submit Documentation Feedback 5 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com Figure 6 shows a typical error curve for the ADC0808. Figure 3. Resistor Ladder and Switch Tree Figure 4. 3-Bit A/D Transfer Curve Figure 5. 3-Bit A/D Absolute Accuracy Curve Figure 6. Typical Error Curve 6 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 Timing Diagram Figure 7. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N Submit Documentation Feedback 7 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics Comparator IIN vs VIN (VCC=VREF=5V) Figure 8. Multiplexer RON vs VIN (VCC=VREF=5V) Figure 9. 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 TRI-STATE Test Circuits and Timing Diagrams t1H, tH1 t0H, tH0 t1H, CL = 10 pF t0H, CL = 10 pF tH1, CL = 50 pF tH0, CL = 50 pF tr tr 90% 50% 10% 90% 50% 10% tH1 tH0 50% 50% Figure 10. TRI-STATE Test Circuits and Timing Diagrams Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N Submit Documentation Feedback 9 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com APPLICATIONS INFORMATION OPERATION RATIOMETRIC CONVERSION The ADC0808, ADC0809 is designed as a complete Data Acquisition System (DAS) for ratiometric conversion systems. In ratiometric systems, the physical variable being measured is expressed as a percentage of full-scale which is not necessarily related to an absolute standard. The voltage input to the ADC0808 is expressed by the equation * * * * * * VIN= Input voltage into the ADC0808 Vfs= Full-scale voltage VZ= Zero voltage DX= Data point being measured DMAX= Maximum data limit DMIN= Minimum data limit (1) A good example of a ratiometric transducer is a potentiometer used as a position sensor. The position of the wiper is directly proportional to the output voltage which is a ratio of the full-scale voltage across it. Since the data is represented as a proportion of full-scale, reference requirements are greatly reduced, eliminating a large source of error and cost for many applications. A major advantage of the ADC0808, ADC0809 is that the input voltage range is equal to the supply range so the transducers can be connected directly across the supply and their outputs connected directly into the multiplexer inputs, (Figure 11). Ratiometric transducers such as potentiometers, strain gauges, thermistor bridges, pressure transducers, etc., are suitable for measuring proportional relationships; however, many types of measurements must be referred to an absolute standard such as voltage or current. This means a system reference must be used which relates the full-scale voltage to the standard volt. For example, if VCC=VREF=5.12V, then the full-scale range is divided into 256 standard steps. The smallest standard step is 1 LSB which is then 20 mV. RESISTOR LADDER LIMITATIONS The voltages from the resistor ladder are compared to the selected into 8 times in a conversion. These voltages are coupled to the comparator via an analog switch tree which is referenced to the supply. The voltages at the top, center and bottom of the ladder must be controlled to maintain proper operation. The top of the ladder, Ref(+), should not be more positive than the supply, and the bottom of the ladder, Ref(-), should not be more negative than ground. The center of the ladder voltage must also be near the center of the supply because the analog switch tree changes from N-channel switches to P-channel switches. These limitations are automatically satisfied in ratiometric systems and can be easily met in ground referenced systems. Figure 12 shows a ground referenced system with a separate supply and reference. In this system, the supply must be trimmed to match the reference voltage. For instance, if a 5.12V is used, the supply should be adjusted to the same voltage within 0.1V. Figure 11. Ratiometric Conversion System 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 The ADC0808 needs less than a milliamp of supply current so developing the supply from the reference is readily accomplished. In Figure 13 a ground referenced system is shown which generates the supply from the reference. The buffer shown can be an op amp of sufficient drive to supply the milliamp of supply current and the desired bus drive, or if a capacitive bus is driven by the outputs a large capacitor will supply the transient supply current as seen in Figure 14. The LM301 is overcompensated to insure stability when loaded by the 10 F output capacitor. The top and bottom ladder voltages cannot exceed VCC and ground, respectively, but they can be symmetrically less than VCC and greater than ground. The center of the ladder voltage should always be near the center of the supply. The sensitivity of the converter can be increased, (i.e., size of the LSB steps decreased) by using a symmetrical reference system. In Figure 15, a 2.5V reference is symmetrically centered about VCC/2 since the same current flows in identical resistors. This system with a 2.5V reference allows the LSB bit to be half the size of a 5V reference system. Figure 12. Ground Referenced Conversion System Using Trimmed Supply Figure 13. Ground Referenced Conversion System with Reference Generating VCC Supply Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N Submit Documentation Feedback 11 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com Figure 14. Typical Reference and Supply Circuit RA=RB *Ratiometric transducers Figure 15. Symmetrically Centered Reference CONVERTER EQUATIONS The transition between adjacent codes N and N+1 is given by: (2) The center of an output code N is given by: (3) The output code N for an arbitrary input are the integers within the range: Where: * * * * * 12 VIN=Voltage at comparator input VREF(+)=Voltage at Ref(+) VREF(-)=Voltage at Ref(-) VTUE=Total unadjusted error voltage (typically VREF(+)/512) Submit Documentation Feedback (4) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N ADC0808-N, ADC0809-N www.ti.com SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 ANALOG COMPARATOR INPUTS The dynamic comparator input current is caused by the periodic switching of on-chip stray capacitances. These are connected alternately to the output of the resistor ladder/switch tree network and to the comparator input as part of the operation of the chopper stabilized comparator. The average value of the comparator input current varies directly with clock frequency and with VIN as shown in Figure 8. If no filter capacitors are used at the analog inputs and the signal source impedances are low, the comparator input current should not introduce converter errors, as the transient created by the capacitance discharge will die out before the comparator output is strobed. If input filter capacitors are desired for noise reduction and signal conditioning they will tend to average out the dynamic comparator input current. It will then take on the characteristics of a DC bias current whose effect can be predicted conventionally. Typical Application *Address latches needed for 8085 and SC/MP interfacing the ADC0808 to a microprocessor Table 2. Microprocessor Interface Table PROCESSOR READ WRITE INTERRUPT (COMMENT) 8080 MEMR MEMW INTR (Thru RST Circuit) 8085 RD WR INTR (Thru RST Circuit) Z-80 RD WR INT (Thru RST Circuit, Mode 0) SC/MP NRDS NWDS SA (Thru Sense A) 6800 VMA*2*R/W VMA**R/W IRQA or IRQB (Thru PIA) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N Submit Documentation Feedback 13 ADC0808-N, ADC0809-N SNAS535H - OCTOBER 1999 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision G (March 2013) to Revision H * 14 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 13 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0808-N ADC0809-N PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ADC0808CCN NRND PDIP N 28 13 TBD Call TI Call TI -40 to 85 ADC0808CCN ADC0808CCN/NOPB ACTIVE PDIP N 28 13 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM -40 to 85 ADC0808CCN ADC0808CCV NRND PLCC FN 28 35 TBD Call TI Call TI -40 to 85 ADC0808 CCV ADC0808CCV/NOPB ACTIVE PLCC FN 28 35 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0808 CCV ADC0808CCVX NRND PLCC FN 28 750 TBD Call TI Call TI -40 to 85 ADC0808 CCV ADC0808CCVX/NOPB ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0808 CCV ADC0809CCN NRND PDIP N 28 13 TBD Call TI Call TI -40 to 85 ADC0809CCN ADC0809CCN/NOPB ACTIVE PDIP N 28 13 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM -40 to 85 ADC0809CCN ADC0809CCV NRND PLCC FN 28 35 TBD Call TI Call TI -40 to 85 ADC0809 CCV ADC0809CCV/NOPB ACTIVE PLCC FN 28 35 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0809 CCV ADC0809CCVX NRND PLCC FN 28 750 TBD Call TI Call TI -40 to 85 ADC0809 CCV ADC0809CCVX/NOPB ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0809 CCV (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MPDI008 - OCTOBER 1994 N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE 24 PIN SHOWN A 24 13 0.560 (14,22) 0.520 (13,21) 1 12 0.060 (1,52) TYP 0.200 (5,08) MAX 0.610 (15,49) 0.590 (14,99) 0.020 (0,51) MIN Seating Plane 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.125 (3,18) MIN 0.010 (0,25) M PINS ** 0- 15 0.010 (0,25) NOM 24 28 32 40 48 52 A MAX 1.270 (32,26) 1.450 (36,83) 1.650 (41,91) 2.090 (53,09) 2.450 (62,23) 2.650 (67,31) A MIN 1.230 (31,24) 1.410 (35,81) 1.610 (40,89) 2.040 (51,82) 2.390 (60,71) 2.590 (65,79) DIM 4040053 / B 04/95 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Falls within JEDEC MS-011 Falls within JEDEC MS-015 (32 pin only) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPLC004A - OCTOBER 1994 FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER 20 PIN SHOWN Seating Plane 0.004 (0,10) 0.180 (4,57) MAX 0.120 (3,05) 0.090 (2,29) D D1 0.020 (0,51) MIN 3 1 19 0.032 (0,81) 0.026 (0,66) 4 E 18 D2 / E2 E1 D2 / E2 8 14 0.021 (0,53) 0.013 (0,33) 0.007 (0,18) M 0.050 (1,27) 9 13 0.008 (0,20) NOM D/E D2 / E2 D1 / E1 NO. OF PINS ** MIN MAX MIN MAX MIN MAX 20 0.385 (9,78) 0.395 (10,03) 0.350 (8,89) 0.356 (9,04) 0.141 (3,58) 0.169 (4,29) 28 0.485 (12,32) 0.495 (12,57) 0.450 (11,43) 0.456 (11,58) 0.191 (4,85) 0.219 (5,56) 44 0.685 (17,40) 0.695 (17,65) 0.650 (16,51) 0.656 (16,66) 0.291 (7,39) 0.319 (8,10) 52 0.785 (19,94) 0.795 (20,19) 0.750 (19,05) 0.756 (19,20) 0.341 (8,66) 0.369 (9,37) 68 0.985 (25,02) 0.995 (25,27) 0.950 (24,13) 0.958 (24,33) 0.441 (11,20) 0.469 (11,91) 84 1.185 (30,10) 1.195 (30,35) 1.150 (29,21) 1.158 (29,41) 0.541 (13,74) 0.569 (14,45) 4040005 / B 03/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-018 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated