APEM www.apem.com
Note: The company reserves the right to change specifications without notice.
FR series
Hall effect 3-position thumb controls
Distinctive features and specifications
NOTE: All values are nominal.
Non-contact Hall effect technology
Three position, ON-OFF-ON analog output
3 million lifecycles
Submersible to 1m (3.28ft) per IP68
Choice of handle color
Redundant outputs available
MECHANICAL
• Initial Actuation Force:
260g Nominal into position 23
360g Nominal out of position 23
• Maximum Vertical Load: 200N3
• Maximum Horizontal Load: 150N3
• Mechanical Life: 3,000,000 full forward to full back
MATERIALS
• Handle/Actuator: Glass filled nylon
• Body: Glass filled nylon
• Boot: Silicone
ENVIRONMENTAL
• Operating Temperature: -400C to +850C (-400F to +1850F)
• Storage Temperature: -400C to +850C (-400F to +1850F)
• Sealing: Submersible to 1m per IP684
• EMC Immunity Level: EN61000-4-3
• EMC Emissions Level: EN61000-6-3:2001
• ESD: EN61000-4-2
ELECTRICAL
• Supply Voltage Range: 5.00V ± 0.01V
• Reverse Polarity Max: 10V
• Overvoltage Max: 20V
• Return to Center Voltage Tolerance (POS2): 2.50V ±0.50V
• Output Voltage Tolerance at Full Travel/Detent Position
(POS1, POS3): ±0.25V
Handle
0 None
1 Castle
2 Winged Hat
3 Conical
A Handle 1, 2, 3
Termination1
1 22 AWG 25cm PTFE
2 28 AWG 25cm PTFE
3 2.54mm (0.100") Pitch
TE Connector
4 2.54mm (0.100") Pitch
TE Connector with
wire harness
Operation
U Single Axis
Output Options
POS1/POS2/POS3
01 0.25/2.5/4.75VDC
02 0.5/2.5/4.5VDC
03 1.0/2.5/4.0VDC
05 0.25/2.5/4.75VDC
0.25/2.5/4.75VDC
06 0.5/2.5/4.5VDC
0.5/2.5/4.5VDC
07 1.0/2.5/4.0VDC
1.0/2.5/4.0VDC
09 0.5/2.5/4.5VDC
4.5/2.5/0.5VDC
10 0.25/2.5/4.75VDC
4.75/2.5/0.25VDC
11 1.0/2.5/4.0VDC
4.0/2.5/1.0VDC
Mounting Options
N None
D Drop-in
R Rear Mount
A Drop-in and Rear Mount
SERIES
Power Supply
A Single
B Independent2
Handle Color
1 Black
2 Red
3 Yellow
FR A
NOTES:
Mounting accessories.
Standard hardware includes: – For the Drop-in option: 4 push in connectors, drop-in bezel and an O-ring.
– For the Rear mount option: 4 x 1/2 FH SS Phil Screws and a rear mount bezel.
1-1 – Wires are thick, robust, and best suited for stand alone applications.
1-2 – Wires are thin and best suited for tightly constrained wire routing.
2 Only available on dual output.
Not available with Termination Options 3 or 4.
3 Force applied to the top of the castle cap.
4 All options are IP68 rated, however Drop-in mounting does not prevent panel ingress.
APEMwww.apem.com
Note: The company reserves the right to change specifications without notice.
FR series
Hall effect 3-position thumb controls
Overview
NOTE: Dimensions are in mm/(inch).
HANDLE OPTIONS
1. CASTLE 2. WINGED HAT 3. CONICAL
.735
.676
Ø17.17
(0.676)
18.67
(0.735)
.723
Ø18.36
(0.723)
19.84
(0.781)
.681
.801
Ø17.30
(0.681)
20.35
(0.801)
.790
.556
.995
50°
POS 1 POS 3
POS 2
INDEX NOTCH
90º FROM DIRECTION OF TRAVEL
10in
22AWG
20.07
(0.79)
14.12
(0.556)
Ø25.27
(0.995)
254.00
(10.00)
22AWG
APEM www.apem.com FR_JOYST1412R1US
Note: The company reserves the right to change specifications without notice.
FR series
Hall effect 3-position thumb controls
Overview
24.64
(0.97)
Ø25.65
(1.01)
Ø2.87
(0.113)
24.64
(0.97)
CHAMFERED
FOR #4 FLAT
HEAD SCREW
(4 PLACES)
1.00 (0.04) x 45º
CHAMFER
DROP-IN OPTION CUTOUT DIMENSIONS
REAR MOUNT OPTION CUTOUT DIMENSIONS
REAR MOUNT
BEZEL
4 x 1/2 FH SS PHIL SCREW
Ø2.87
(0.113)
Ø25.65
(1.01)
24.64
(0.97)
24.64
(0.97)
DROP-IN
BEZEL
O-RING
4 x PUSH IN CONNECTORS
NOTES:
1 The maximum panel thickness for the Rear Mount configuration is 2.032mm/(0.08in).
2 The under panel depth for the Drop-in configuration is 16.02mm/(0.631in).
3 Dimensions are in mm/(inch).
WIRING SPECIFICATION
• Black: Ground & button common
• Red: Power (5V)
• Blue X axis output (alpha)
• Blue/White Stripe: X axis output (beta)
• Red/White Stripe: Power (5V) (beta)
• Black/White Stripe: Ground (beta)
PINOUT SPECIFICATION
TE 3-647166-5 TE 3-647166-7
Pin 1 Not used Not used
Pin 2 5VDC GND
Pin 3 X (alpha) X (alpha)
Pin 4 GND Not used
Pin 5 Not used Not used
Pin 6 – 5VDC
Pin 7 – X (beta)
CONNECTOR TERMINATION OPTION
Single output configurations feature a five position TE
3-647166-5 connector. Dual output configurations feature
a seven position TE 3-647166-7 connector. A mating
harness is not included, but may be specified for single
output configurations at the time of order for an additional
charge. The five function harness is part number 505-499.
PIN 1 PIN 1
