S-1133 Series
www.ablicinc.com
HIGH RIPPLE-REJECTION AND LOW DROPOUT
MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
© ABLIC Inc., 2006-2015 Rev.3.1_02
1
The S-1133 Series is a positive voltage regulator with a low dropout voltage, high output voltage accuracy, and low current
consumption (300 mA output current) developed based on CMOS technology.
A 1 F small ceramic capacitor can be used*1. It operates with low current consumption of 60 A typ. The S-1133 Series
includes an overcurrent protection circuit that prevents the output current from exceeding the current capacity of the output
transistor and a thermal shutdown circuit that prevents damage due to overheating.
In addition to the types in which output voltage is set inside the IC, a type for which output voltage can be set via an external
resistor is added to a lineup (S-1133x00 Series). SOT-89-5 and super-small SNT-8A packages realize high-density
mounting. This, in addition to low current consumption, makes the S-1133 Series ideal for mobile devices.
*1. A ceramic capacitor of 2.2 F or more can be used for products whose output voltage is 1.7 V or less.
Features
Output voltage (internally set): 1.2 V to 6.0 V, selectable in 0.1 V step.
Output voltage (externally set): 1.8 V to 8.2 V, settable via external resistor
(S-1133B00/S-1133A00)
Input voltage: 2.0 V to 10 V
Output voltage accuracy: 1.0% (1.2 V to 1.4 V output product: 15 mV)
Dropout voltage: 130 mV typ. (3.0 V output product, IOUT = 100 mA)
Current consumption: During operation: 60 A typ., 90 A max.
During power-off: 0.1 A typ., 1.0 A max.
Output current: Possible to output 300 mA (VIN VOUT
(
S
)
1.0 V)*1
Input and output capacitors:
A
ceramic capacitor of 1.0 F or more can be used.
(A ceramic capacitor of 2.2 F or more can be used for products whose
output voltage is 1.7 V or less.)
Ripple rejection: 70 dB typ. (1.2 V output product, f = 1.0 kHz)
Built-in overcurrent protection circuit: Limits overcurrent of output transistor.
Built-in thermal shutdown circuit: Prevents damage caused by heat.
Built-in ON / OFF circuit: Ensures long battery life.
Operation temperature range: Ta = 40C to 85C
Lead-free, Sn 100%, halogen-free*2
*1. Attention should be paid to the power dissipation of the package when the output current is large.
*2. Refer to “ Product Name Structure” for details.
Applications
Power supply for battery-powered devices
Power supply for communication devices
Power supply for home electric appliances
Packages
SOT-89-5
SNT-8A
www.ablic.com
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
2
Block Diagrams
1. Types in which output voltage is internally set (S-1133x12 to S-1133x60)
*1. Parasitic diode
*1
ON / OFF
VIN
VSS
VOUT
Reference
voltage circuit
ON / OFF
circuit
Overcurrent
protection circuit
Thermal
shutdown circuit
Figure 1
2. Types in which output voltage is externally set (S-1133B00 and S-1133A00 only)
*1. Parasitic diode
*1
ON / OFF
VIN
VSS
VOUT
Reference
voltage circuit
ON / OFF
circuit
Overcurrent
protection circuit
Thermal
shutdown circuit
VADJ
Figure 2
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
3
Product Name Structure
The product types, output voltage, and package types for the S-1133 Series can be selected at the user’s request.
Refer to the “1. Product name” for the meanings of the characters in the product name, “2. Package” regarding the
package drawings and “3. Product name list” for the full product names.
1. Product name
1. 1 SOT-89-5
S-1133 x xx U5T1 x
Output voltage
00: Externally set
12 to 60: Internally set
(e.g., when the output voltage is 1.2 V, it is expressed as 12.)
Environmental code
U: Lead-free (Sn 100%), halogen-free
G: Lead-free (for details, please contact our sales office)
Product type*2
A: ON / OFF pin negative logic
B: ON / OFF pin positive logic
Package abbreviation and packing specifications*1
U5T1: SOT-89-5, Tape
*1. Refer to the tape drawing.
*2. Refer to “3. ON / OFF pin” in “ Operation”.
1. 2 SNT-8A
S-1133 x xx I8T1 U
Output voltage
00: Externally set
12 to 60: Internally set
(e.g., when the output voltage is 1.2 V, it is expressed as 12.)
Environmental code
U: Lead-free
(
Sn 100%
)
, halo
g
en-free
Product type*2
A: ON / OFF pin negative logic
B: ON / OFF pin positive logic
Package abbreviation and packing specifications*1
I8T1: SNT-8A, Tape
*1. Refer to the tape drawing.
*2. Refer to “3. ON / OFF pin” in “ Operation”.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
4
2. Packages
Package Name Drawing Code
Package Tape Reel Land
SOT-89-5 UP005-A-P-SD UP005-A-C-SD UP005-A-R-SD UP005-A-L-S1
SNT-8A PH008-A-P-SD PH008-A-C-SD PH008-A-R-SD PH008-A-L-SD
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
5
3. Product name list
Table 1 (1/2)
Output Voltage SOT-89-5 SNT-8A
Externally set S-1133B00-U5T1x S-1133B00-I8T1U
1.2 V 15 mV S-1133B12-U5T1x S-1133B12-I8T1U
1.3 V 15 mV S-1133B13-U5T1x S-1133B13-I8T1U
1.4 V 15 mV S-1133B14-U5T1x S-1133B14-I8T1U
1.5 V 1.0% S-1133B15-U5T1x S-1133B15-I8T1U
1.6 V 1.0% S-1133B16-U5T1x S-1133B16-I8T1U
1.7 V 1.0% S-1133B17-U5T1x S-1133B17-I8T1U
1.8 V 1.0% S-1133B18-U5T1x S-1133B18-I8T1U
1.9 V 1.0% S-1133B19-U5T1x S-1133B19-I8T1U
2.0 V 1.0% S-1133B20-U5T1x S-1133B20-I8T1U
2.1 V 1.0% S-1133B21-U5T1x S-1133B21-I8T1U
2.2 V 1.0% S-1133B22-U5T1x S-1133B22-I8T1U
2.3 V 1.0% S-1133B23-U5T1x S-1133B23-I8T1U
2.4 V 1.0% S-1133B24-U5T1x S-1133B24-I8T1U
2.5 V 1.0% S-1133B25-U5T1x S-1133B25-I8T1U
2.6 V 1.0% S-1133B26-U5T1x S-1133B26-I8T1U
2.7 V 1.0% S-1133B27-U5T1x S-1133B27-I8T1U
2.8 V 1.0% S-1133B28-U5T1x S-1133B28-I8T1U
2.9 V 1.0% S-1133B29-U5T1x S-1133B29-I8T1U
3.0 V 1.0% S-1133B30-U5T1x S-1133B30-I8T1U
3.1 V 1.0% S-1133B31-U5T1x S-1133B31-I8T1U
3.2 V 1.0% S-1133B32-U5T1x S-1133B32-I8T1U
3.3 V 1.0% S-1133B33-U5T1x S-1133B33-I8T1U
3.4 V 1.0% S-1133B34-U5T1x S-1133B34-I8T1U
3.5 V 1.0% S-1133B35-U5T1x S-1133B35-I8T1U
3.6 V 1.0% S-1133B36-U5T1x S-1133B36-I8T1U
3.7 V 1.0% S-1133B37-U5T1x S-1133B37-I8T1U
3.8 V 1.0% S-1133B38-U5T1x S-1133B38-I8T1U
3.9 V 1.0% S-1133B39-U5T1x S-1133B39-I8T1U
4.0 V 1.0% S-1133B40-U5T1x S-1133B40-I8T1U
4.1 V 1.0% S-1133B41-U5T1x S-1133B41-I8T1U
4.2 V 1.0% S-1133B42-U5T1x S-1133B42-I8T1U
4.3 V 1.0% S-1133B43-U5T1x S-1133B43-I8T1U
4.4 V 1.0% S-1133B44-U5T1x S-1133B44-I8T1U
4.5 V 1.0% S-1133B45-U5T1x S-1133B45-I8T1U
4.6 V 1.0% S-1133B46-U5T1x S-1133B46-I8T1U
4.7 V 1.0% S-1133B47-U5T1x S-1133B47-I8T1U
4.8 V 1.0% S-1133B48-U5T1x S-1133B48-I8T1U
4.9 V 1.0% S-1133B49-U5T1x S-1133B49-I8T1U
5.0 V 1.0% S-1133B50-U5T1x S-1133B50-I8T1U
5.1 V 1.0% S-1133B51-U5T1x S-1133B51-I8T1U
5.2 V 1.0% S-1133B52-U5T1x S-1133B52-I8T1U
5.3 V 1.0% S-1133B53-U5T1x S-1133B53-I8T1U
5.4 V 1.0% S-1133B54-U5T1x S-1133B54-I8T1U
5.5 V 1.0% S-1133B55-U5T1x S-1133B55-I8T1U
5.6 V 1.0% S-1133B56-U5T1x S-1133B56-I8T1U
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
6
Table 1 (2/2)
Output Voltage SOT-89-5 SNT-8A
5.7 V 1.0% S-1133B57-U5T1x S-1133B57 I8T1U
5.8 V 1.0% S-1133B58-U5T1x S-1133B58-I8T1U
5.9 V 1.0% S-1133B59-U5T1x S-1133B59-I8T1U
6.0 V 1.0% S-1133B60-U5T1x S-1133B60-I8T1U
Remark 1. Please contact our sales office for type A products.
2. x: G or U
3. Please select products of environmental code = U for Sn 100%, halogen-free products.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
7
Pin Configurations
1. SOT-89-5
132
45
Top view
Table 2
Pin No. Symbol Description
1
VADJ Output voltage adjustment pin
(S-1133B00/S-1133A00 only)
NC*1 No connection
(S-1133x12 to S-1133x60)
2 VSS GND pin
3 ON / OFF ON / OFF pin
4 VIN Voltage input pin
5 VOUT Voltage output pin
*1. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
Figure 3
2. SNT-8A
7
6
5
8
2
3
4
1
Top view
Table 3
Pin No. Pin Name Functions
1 VOUT*1 Voltage output pin
2 VOUT*1 Voltage output pin
3
NC*2 No connection
(S-1133x12 to S-1133x60)
VADJ Output voltage adjustment pin
(S-1133B00/S-1133A00 only)
Figure 4 4 NC*2 No connection
5 VSS GND pin
6 ON / OFF ON / OFF pin
7 VIN*3 Voltage input pin
8 VIN*3 Voltage input pin
*1. Although pins of number 1 and 2 are connected internally, be
sure to short-circuit them nearest in use.
*2. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
*3. Although pins of number 7 and 8 are connected internally, be
sure to short-circuit them nearest in use.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
8
Absolute Maximum Ratings
Table 4
(Ta 25 C unless otherwise specified)
Item Symbol Absolute Maximum Rating Unit
Input voltage
VIN V
SS 0.3 to VSS 12 V
VON / OFF V
SS 0.3 to VSS 12 V
VADJ V
SS 0.3 to VSS 12 V
Output voltage VOUT V
SS 0.3 to VIN 0.3 V
Power dissipation SOT-89-5 PD 1000*1 mW
SNT-8A 450*1 mW
Operation ambient temperature To
pr
40 to 85 C
Storage temperature Tst
g
40 to 125 C
*1. When mounted on printed circuit board
[Mounted Board]
(1) Board size : 114.3 mm 76.2 mm t1.6 mm
(2) Board name : JEDEC STANDARD51-7
Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
0 50 100 150
1200
800
0
Power Dissipation (PD) [mW]
Ambient Temperature (Ta) [C]
400
SNT-8A
SOT-89-5
Figure 5 Power Dissipation of Packages (Mounted on Printed Circuit Board)
Caution The thermal shutdown circuit may operate when the junction temperature is around 150 C.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
9
Electrical Characteristics
1. Types in which output voltage is internally set (S-1133x12 to S-1133x60)
Table 5
(Ta 25 C unless otherwise specified)
Item Symbol Conditions Min. Typ. Max. Unit
Test
Circuit
Output voltage
*1
VOUT(E)
V
IN
V
OUT(S)
1.0 V,
I
OUT
100 mA
1.2 V
V
OUT(S)
1.4 V
VOUT(S)
0.015 VOUT(S) VOUT(S)
0.015 V 1
1.5 V
V
OUT(S)
6.0 V
VOUT(S)
0.99 VOUT(S) VOUT(S)
1.01 V 1
Output current
*2
IOUT
V
IN
V
OUT
(
S
)
1.0 V
300*5 mA 3
Dropout voltage
*3
Vdrop
I
OUT
100 mA
V
OUT
(
S
)
1.2 V
0.8 0.84 0.88 V 1
V
OUT
(
S
)
1.3 V
0.74 0.78 V 1
V
OUT
(
S
)
1.4 V
0.64 0.68 V 1
1.5 V
V
OUT
(
S
)
1.9 V
0.54 0.58 V 1
2.0 V
V
OUT
(
S
)
2.4 V
0.15 0.23 V 1
2.5 V
V
OUT
(
S
)
2.9 V
0.14 0.21 V 1
3.0 V
V
OUT
(
S
)
3.2 V
0.13 0.19 V 1
3.3 V
V
OUT
(
S
)
6.0 V
0.10 0.15 V 1
Line regulation
OUTIN
OUT1
VV
V
V
OUT(S)
0.5 V
V
IN
10 V, I
OUT
100 mA
0.02 0.2 %/V 1
Load regulation
VOUT2
V
IN
V
OUT(S)
1.0 V,
1.0 mA
I
OUT
100 mA
15 40 mV 1
Output voltage
temperature coefficient
*4
OUT
OUT
VTa
V
V
IN
V
OUT(S)
1.0 V, I
OUT
30 mA,
40
C
Ta
85
C
130 ppm/C1
Current consumption
during operation
ISS1
V
IN
V
OUT(S)
1.0 V, ON / OFF pin
ON,
no load
60 90 A 2
Current consumption
during power-off
ISS2
V
IN
V
OUT(S)
1.0 V, ON / OFF pin
OFF,
no load
0.1 1.0 A 2
Input voltage
VIN
2.0 10 V
ON / OFF pin
input voltage “H”
VSH
V
IN
V
OUT(S)
1.0 V, R
L
1.0 k
1.5 V 4
ON / OFF pin
input voltage “L”
VSL
V
IN
V
OUT(S)
1.0 V, R
L
1.0 k
0.25 V 4
ON / OFF pin
input current “H”
ISH
V
IN
V
OUT(S)
1.0 V, V
ON / OFF
7 V
0.1 0.1 A 4
ON / OFF pin
input current “L”
ISL
V
IN
V
OUT(S)
1.0 V, V
ON / OFF
0 V
0.1 0.1 A 4
Ripple rejection
RR
V
IN
V
OUT(S)
1.0 V,
f
1.0 kHz,
V
rip
0.5 Vrms,
I
OUT
50 mA
1.2 V
V
OUT(S)
1.5 V
70 dB 5
1.6 V
V
OUT(S)
3.0 V
65 dB 5
3.1 V
V
OUT(S)
6.0 V
60 dB 5
Short-circuit current
Ishort
V
IN
V
OUT(S)
1.0 V, ON / OFF pin
ON,
V
OUT
0 V
200 mA 3
Thermal shutdown
detection temperature
TSD
Junction temperature
150 C
Thermal shutdown
release temperature
TSR
Junction temperature
120 C
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
10
*1. V
OUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT ( 100 mA) and inputting VOUT
(
S
)
1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT
(
E
)
after gradually increasing the output current.
*3. V
drop VIN1 (VOUT3 0.98)
V
OUT3 is the output voltage when VIN VOUT(S) 1.0 V and IOUT 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta []
mV/°C *1 = VOUT(S) []
V*2 VOUT
TaVOUT
[]
ppm/°C *3 1000
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
11
2. Types in which output voltage is externally set (S-1133B00 and S-1133A00 only)
Table 6
(Ta 25 C unless otherwise specified)
Item Symbol Conditions Min. Typ. Max. Unit
Test
Circuit
Output voltage of adjust
pin
*1
VVADJ
V
VADJ
V
OUT
, V
IN
V
OUT(S)
1.0 V,
I
OUT
100 mA
1.782 1.800 1.818 V 6
Output voltage range
VROUT
1.8 8.2 V 11
Internal resistance value
of adjust pin
RVADJ
200 k
Output current
*2
IOUT
V
IN
V
OUT
(
S
)
1.0 V
300*5 mA 8
Dropout voltage
*3
Vdro
p
I
OUT
100 mA, V
VADJ
V
OUT
, V
OUT
(
S
)
1.8 V
0.24 0.28 V 6
Line regulation
OUTIN
OUT1
VV
V
V
VADJ
V
OUT
, V
OUT(S)
0.5 V
V
IN
10 V,
I
OUT
100 mA
0.02 0.2 %/V 6
Load regulation
VOUT2
V
VADJ
V
OUT
, V
IN
V
OUT(S)
1.0 V,
1.0 mA
I
OUT
100 mA
15 40 mV 6
Output voltage
temperature coefficient
*4
OUT
OUT
VTa
V
V
IN
V
OUT(S)
1.0 V, I
OUT
30 mA,
40
C
Ta
85
C
130 ppm/C6
Current consumption
during operation
ISS1
V
IN
V
OUT(S)
1.0 V, V
OUT
V
VADJ
,
ON / OFF pin
ON, no load
60 90 A 7
Current consumption
during power-off
ISS2
V
IN
V
OUT(S)
1.0 V, V
OUT
V
VADJ
,
ON / OFF pin
OFF, no load
0.1 1.0 A 7
Input voltage
VIN
2.0 10 V
ON / OFF pin
input voltage “H”
VSH
V
IN
V
OUT(S)
1.0 V, R
L
1.0 k
1.5 V
9
ON / OFF pin
input voltage “L”
VSL
V
IN
V
OUT(S)
1.0 V, R
L
1.0 k
0.25 V 9
ON / OFF pin
input current “H”
ISH
V
IN
V
OUT(S)
1.0 V, V
ON / OFF
7 V
0.1 0.1 A 9
ON / OFF pin
input current “L”
ISL
V
IN
V
OUT(S)
1.0 V, V
ON / OFF
0 V
0.1 0.1 A 9
Ripple rejection
RR
V
VADJ
V
OUT
, V
IN
V
OUT(S)
1.0 V,
f
1.0 kHz,
V
rip
0.5 Vrms,
I
OUT
50 mA, V
OUT(S)
1.8 V
65 dB 10
Short-circuit current
Ishort
V
IN
V
OUT(S)
1.0 V, ON / OFF pin
ON,
V
OUT
0 V
200 mA 8
Thermal shutdown
detection temperature
TSD
Junction temperature
150 C
Thermal shutdown
release temperature
TSR
Junction temperature
120 C
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
12
*1. V
OUT
(
S
)
: Set output voltage ( = 1.8 V)
*2. The output current at which the output voltage becomes 95% of VVADJ after gradually increasing the output current.
*3. V
drop VIN1 (VOUT3 0.98)
V
OUT3 is the output voltage when VIN VOUT(S) 1.0 V and IOUT 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in the temperature of the output voltage [mV/C] is calculated using the following equation.
VOUT
Ta []
mV/°C *1 = VOUT(S) []
V*2 VOUT
TaVOUT
[]
ppm/°C *3 1000
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
13
Test Circuits
1.
VSS
VOUT
ON / OFF
VIN
V
A
Set to ON
Figure 6
2.
VSS
VOUT
ON / OFF
VIN
Set to VIN or
GND
A
Figure 7
3.
VSS
VOUT
ON / OFF
VIN
V
A
Set to ON
Figure 8
4.
VSS
VOUT
ON / OFF
VIN
A V
RL
Figure 9
5.
VSS
VOUT
ON / OFF
VIN
V
Set to ON
RL
Figure 10
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
14
6.
VSS
VOUT
ON / OFF
VIN
V
A
Set to ON
VADJ
Figure 11
7.
VSS
VOUT
ON / OFF
VIN
Set to VIN or
GND
A
VADJ
Figure 12
8.
VSS
VOUT
ON / OFF
VIN
V
A
Set to ON
VADJ
Figure 13
9.
VSS
VOUT
ON / OFF
VIN
V
A RL
VADJ
Figure 14
10.
VSS
VOUT
ON / OFF
VIN
V
Set to ON
RL
VADJ
Figure 15
11.
VSS
VOUT
ON / OFF
VIN
V
A
Set to ON
VADJ
Figure 16
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
15
Standard Circuit
VSS
VOUT
ON / OFF
VIN
CIN
*1
CL
*
2
Input Output
GND
Single GND
*1. C
IN is a capacitor for stabilizing the input.
A ceramic capacitor of 2.2 F or more can be used as the output capacitor for
products whose output voltage is 1.7 V or less.
*2. A ceramic capacitor of 1.0 F or more can be used for CL.
A ceramic capacitor of 2.2 F or more can be used as the output capacitor for
products whose output voltage is 1.7 V or less.
Figure 17
Caution The above connection diagram and constant will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constant.
Condition of Application
Input capacitor (CIN) : 1.0 F or more*1
Output capacitor (CL) : 1.0 F or more*1
ESR of output capacitor : 1.0 or less
*1. 2.2 F or more for products whose output voltage is 1.7 V or less
Caution Generally a series regulator may cause oscillation, depending on the selection of external parts.
Check that no oscillation occurs with the application using the above capacitor.
Selection of Input and Output Capacitors (CIN, CL)
The S-1133 Series requires an output capacitor between the VOUT pin and the VSS pin for phase compensation. Operation
is stabilized by a ceramic capacitor with an output capacitance of 1.0 F or more*1 in the entire temperature range. When
using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must be 1.0 F or more,
and the ESR must be 1.0 or less.
The value of the output overshoot or undershoot transient response varies depending on the value of the output capacitor.
Perform thorough evaluation using the actual application, including temperature characteristics.
*1. The capacitance is 2.2 F or more for products whose output voltage is 1.7 V or less.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
16
Explanation of Terms
1. Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2. Low ESR
A capacitor whose ESR (Equivalent Series Resistance) is low. The S-1133 Series enables use of a low ESR
capacitor, such as a ceramic capacitor, for the output-side capacitor CL. A capacitor whose ESR is 1.0 or less can
be used.
3. Output voltage (VOUT)
The accuracy of the output voltage is ensured at 1.0% under the specified conditions of fixed input voltage*1, fixed
output current, and fixed temperature.
*1. Differs depending on the product.
Caution If the above conditions change, the output voltage value may vary and exceed the accuracy
range of the output voltage. Please see the electrical characteristics and attached
characteristics data for details.
Remark In the types of the S-1133 Series in which the output voltage is 1.2 to 1.4 V, the output voltage accuracy
is 15 mV.
4. Line regulation
VOUT1
VINVOUT
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
5. Load regulation (VOUT2)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the
output voltage changes due to a change in the output current with the input voltage remaining unchanged.
6. Dropout voltage (Vdrop)
Indicates the difference between the input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at VIN
VOUT(S) 1.0 V.
Vdrop VIN1 (VOUT3 0.98)
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
17
7. Output voltage temperature coefficient
VOUT
TaVOUT
The shaded area in Figure 18 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is 130 ppm/C.
V
OUT(E)*1
Example of S-1133B30 typ. product
40 25
0.39 mV/C
V
OUT
[V]
*1. V
OUT(E)
is the value of the output voltage measured at Ta = 25C.
85 Ta [C]
0.39 mV/C
Figure 18
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
VOUT
Ta []
mV/°C *1 = VOUT(S) []
V*2 VOUT
TaVOUT
[]
ppm/°C *3 1000
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
18
Operation
1. Basic operation
Figure 19 shows the block diagram of the S-1133 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant
output voltage which is not influenced by the input voltage and temperature change, to the output transistor.
Current
supply
Reference
voltage circuit
VOUT
*1
*1. Parasitic diode
VSS
VIN
Rs
Rf
Error
amplifier
Vref
Vfb
Figure 19
2. Output transistor
In the S-1133 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN 0.3 V to prevent the voltage regulator from being damaged due to reverse
current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became
higher than VIN.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
19
3. ON / OFF pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in P-channel MOS
FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current consumption significantly.
The VOUT pin becomes the VSS level due to the internally divided resistance of several hundreds k between the
VOUT pin and the VSS pin.
The structure of the ON / OFF pin is as shown in Figure 20. The ON / OFF pin is neither pulled down nor pulled up
internally, so do not use it in the floating status. In addition, note that the current consumption increases if a voltage of
0.3 V to VIN 0.3 V is applied to the ON / OFF pin. When not using the ON / OFF pin, connect it to the VSS pin in the
product A type, and connect it to the VIN pin in B type.
Table 7
Product Type ON/OFF Pin Internal Circuit VOUT Pin Voltage Current Consumption
A “L”: ON Operate Set value ISS1
A “H”: OFF Stop VSS level ISS2
B “L”: OFF Stop VSS level ISS2
B “H”: ON Operate Set value ISS1
VSS
ON / OFF
VIN
Figure 20
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
20
4. Thermal shutdown circuit
The S-1133 Series implements a thermal shutdown circuit to protect the device from damage due to overheating.
When the junction temperature rises to 150 C typ., the thermal shutdown circuit operates and the regulator operation
stops. When the junction temperature drops to 120 C typ., the thermal shutdown circuit is released and the regulator
operation resumes.
If the thermal shutdown circuit starts operating due to self-heating, the regulator operation stops and the output voltage
falls. When the regulator operation has stopped, no self-heat is generated and the temperature of the IC is lowered.
When the temperature has dropped, the thermal shutdown circuit is released, the regulator operation resumes, and
self-heat is generated again. By repeating this procedure, the output voltage waveform forms pulses. Stop or restart of
regulation continues unless decreasing either or both of the input voltage and the output current in order to reduce the
internal power consumption, or decreasing the ambient temperature.
Table 8
Thermal Shutdown Circuit VOUT Pin Voltage
Operation: 150 C typ.*1 VSS level
Release: 120 C typ.*1 Set value
*1. Junction temperature
5. Externally setting output voltage
The S-1133 Series provides the types in which output voltage can be set via the external resistor (S-1133B00/S-
1133A00). The output voltage can be set by connecting a resistor (Ra) between the VOUT pin and the VADJ pin, and a
resistor (Rb) between the VADJ pin and the VSS pin.
The output voltage is determined by the following formulas.
VOUT 1.8 Ra la ······················ (1)
By substituting Ia IVADJ 1.8/Rb to above formula (1),
VOUT 1.8 Ra (IVADJ 1.8/Rb) 1.8 (1.0 Ra/Rb) Ra IVADJ ············ (2)
In above formula (2), Ra IVADJ is a factor for the output voltage error.
Whether the output voltage error is minute is judged depending on the following (3) formula.
By substituting IVADJ 1.8/RVADJ to Ra IVADJ
VOUT 1.8 (1.0 Ra/Rb) 1.8 Ra/RVADJ ······················ (3)
If RVADJ is sufficiently larger than Ra, the error is judged as minute.
VSS
VOUT
VIN VADJ
VOUT
Ra
Rb
Ia
Ib
RVADJ
IVADJ
1.8 V
Figure 21
The following expression is in order to determine output voltage VOUT = 3.0 V.
If resistance Rb = 2 k, substitute RVADJ = 200 k typ. into (3),
Resistance Ra = (3.0 / 1.8-1) ((2 k 200 k) / (2 k + 200 k)) ≒ 1.3 k
Caution The above connection diagrams and constants will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constants.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
21
Precautions
Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting an output capacitor between the VOUT pin and the VSS pin (CL) and a capacitor for stabilizing the input
between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
When setting the output voltage using the external resistor, connect the resistors, Ra between the VOUT pin and the
VADJ pin and Rb between the VADJ pin and the VSS pin close to the respective pins.
In the product that users set the output voltage externally, it is possible to set a voltage arbitrarily; by feeding back
the voltage which is from the VOUT pin to the VADJ pin, after dividing it with the dividers connected between the
VOUT pin and the VADJ pin, and the VADJ pin and the VSS pin.
Note that if any device other than the divider specified above is connected between the VOUT pin and the VADJ pin
or the VADJ pin and the VSS pin, S-1133 Series may not work stably as a voltage regulator IC.
Note that generally the output voltage may increase when a series regulator is used at low load current (1.0 mA or
less).
Note that generally the output voltage may increase due to the leakage current from an output driver when a series
regulator is used at high temperature.
Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-1133 Series. However, be sure to perform sufficient evaluation under the
actual usage conditions for selection, including evaluation of temperature characteristics.
Input capacitor (CIN): 1.0 F or more*1
Output capacitor (CL): 1.0 F or more*1
Equivalent series resistance (ESR): 1.0 or less
*1. The capacitance is 2.2 F or more for products whose output voltage is 1.7 V or less.
The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is
small or an input capacitor is not connected.
If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become
worse. Sufficiently evaluate the output voltage's fluctuation with the actual device.
Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
When the thermal shutdown circuit starts operating and the regulator stops, input voltage may exceed the absolute
maximum ratings.
It will be affected largely when input voltage, output current and inductance of power supply are high.
Perform thorough evaluation using the actual application.
The application conditions for the input voltage, the output voltage, and the load current should not exceed the
package power dissipation.
Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
In determining the output current, attention should be paid to the output current value specified in Table 5 and Table
6 in “ Electrical Characteristics” and footnote *5 of the table.
ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
22
Characteristics (Typical Data)
(1) Output voltage vs. Output current (when load current increases) (Ta 25 C)
S-1133B12 S-1133B30
=
=
S-1133B60
=
Remark In determining the output current, attention
should be paid to the following.
1. The minimum output current value and
footnote *5 in Table 5 and Table 6 in
“ Electrical Characteristics”
2. The package power dissipation
(2) Output voltage vs. Input voltage (Ta 25 C)
S-1133B12 S-1133B30
1.0 1.5 2.0 2.5
VOUT [V]
1.25
1.20
1.15
1.10
1.05
1.00
VIN [V]
1.30
3.53.0
100 mA
I
OUT
= 1 mA
30 mA
2.5 3.0 3.5 4.0 4.5
VOUT [V]
3.0
2.9
2.8
2.7
2.6
2.5
VIN [V]
3.1
5.0
100 mA
I
OUT
= 1 mA
30 mA
S-1133B60
4.5 5.0 6.05.5 7.06.5
VOUT [V]
6.0
5.5
5.0
4.5
VIN [V]
6.5
100 mA
I
OUT
= 1 mA
30 mA
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
23
(3) Dropout voltage vs. Output current
S-1133B12 S-1133B30
°
°
-
°
0100 150 350
V
drop
[V]
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.05
0.10
0
I
OUT
[mA]
50 200 250 300
85C
25C
40C
S-1133B60
0100 150 350
V
drop
[V]
0
I
OUT
[mA]
50 200 250 300
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.05
0.10
85C
25C
40C
(4) Dropout voltage vs. Set output voltage
023
V
drop
[V]
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
V
OUT(S)
[V]
14567
0
300 mA
100 mA
50 mA
10 mA
30 mA
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
24
(5) Output voltage vs. Ambient temperature
S-1133B12 S-1133B30
-
°
-
°
-
-
S-1133B60
°
-
-
(6) Current consumption vs. Input voltage
S-1133B12 S-1133B30
02 5678910
ISS1 [μA]
30
20
0
VIN [V]
134
60
10
40
50
85C
25C40C
02 5678910
ISS1 [μA]
30
20
0
VIN [V]
134
60
10
40
50
85C25C
40C
S-1133B60
02 5678910
ISS1 [μA]
30
20
0
VIN [V]
134
60
10
40
50
85C
25C
40C
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
25
(7) Ripple rejection (Ta 25 C)
S-1133B12
VIN 2.2 V, COUT 2.2 F
S-1133B30
VIN 4.0 V, COUT 1.0 F
10 100 1K 10K 100K
Ripple Rejection [dB]
0
20
40
60
80
Frequency [Hz]
1M
100
50 mA
I
OUT
= 1 mA
100 mA
!
"
#$%
=
S-1133B60
VIN 7.0 V, COUT 1.0 F
!
"
#$%
=
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
26
Reference Data
(1) Input transient response characteristics (Ta 25 C)
S-1133B12
IOUT 100 mA, t
r
tf 5.0 s, COUT 2.2 F, CIN 2.2 F
S-1133B30
IOUT 100 mA, t
r
tf 5.0 s, COUT 1.0 F, CIN 1.0 F
1.36
1.32
1.28
1.24
1.20
1.16
1.12
20 80 120 180
V
OUT
[V]
t [μs]
V
IN
[V]
3.5
3.0
2.5
0.5
1.0
1.5
2.0
0 20 40 60 100 140 160
V
OUT
V
IN
3.16
3.12
3.08
3.04
3.00
2.96
2.92
20 80 120 180
VOUT [V]
t [μs]
VIN [V]
6
5
4
0
1
2
3
0 20 40 60 100 140 160
V
OUT
V
IN
S-1133B60
IOUT 100 mA, t
r
tf 5.0 s, COUT 1.0 F, CIN 1.0 F
6.16
6.12
6.08
6.04
6.00
5.96
5.92
20 80 120 180
V
OUT
[V]
t [μs]
V
IN
[V]
9
8
7
3
4
5
6
0 20 40 60 100 140 160
VOUT
VIN
(2) Load transient response characteristics (Ta 25 C)
S-1133B12
V
IN
2.2 V, C
OUT
2.2
F, C
IN
2.2
F, I
OUT
50 mA
100 mA
S-1133B30
V
IN
4.0 V, C
OUT
1.0
F, C
IN
1.0
F, I
OUT
50 mA
100 mA
40 60 100 160
V
OUT
[V]
1.6
1.5
1.4
1.3
1.2
1.1
1.0
t [μs]
I
OUT
[mA]
150
100
50
150
100
50
0
20 0 20 40 80 120 140
V
OUT
I
OUT
40 60 100 160
V
OUT
[V]
3.16
3.12
3.08
3.04
3.00
2.96
2.92
t [μs]
I
OUT
[mA]
150
100
50
150
100
50
0
20 0 20 40 80 120 140
V
OUT
I
OUT
S-1133B60
V
IN
7.0 V, C
OUT
1.0
F, C
IN
1.0
F, I
OUT
50 mA
100 mA
40 60 100 160
V
OUT
[V]
6.16
6.12
6.08
6.04
6.00
5.96
5.92
t [μs]
I
OUT
[mA]
150
100
50
150
100
50
0
20 0 20 40 80 120 140
V
OUT
I
OUT
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
27
(3) ON / OFF pin transient response characteristics (Ta 25 C)
S-1133B12
VIN 2.2 V, COUT 2.2 F, CIN 2.2 F, IOUT 100 mA
S-1133B30
VIN 4.0 V, COUT 1.0 F, CIN 1.0 F, IOUT 100 mA
V
OUT
[V]
5
4
3
2
1
0
1
V
ON/OFF
[V]
6
4
2
0
6
4
2
40 60 100 160
t [μs]
20 0 20 40 80 120 140
V
ON/OFF
V
OUT
V
OUT
[V]
10
8
6
4
2
0
2
V
ON/OFF
[V]
6
4
2
0
6
4
2
40 60 100 160
t [μs]
20 0 20 40 80 120 140
V
ON/OFF
V
OUT
S-1133B60
VIN 7.0 V, COUT 1.0 F, CIN 1.0 F, IOUT 100 mA
V
OUT
[V]
10
8
6
4
2
0
2
12
14
V
ON/OFF
[V]
8
4
2
0
8
6
4
2
6
40 60 100 160
t [μs]
20 0 20 40 80 120 140
V
ON/OFF
V
OUT
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
S-1133 Series Rev.3.1_02
28
Marking Specifications
1. SOT-89-5
(1) (2) (3)
(4) (5) (6)
123
45
Top view
(1) to (3) : Product code (Refer to Product name vs. Product code.)
(4) to (6) : Lot number
Product name vs. Product code
Product name Product code Product name Product code
(1) (2) (3) (1) (2) (3)
S-1133B00-U5T1x Q 8 A S-1133B36-U5T1x Q 8 Z
S-1133B12-U5T1x Q 8 B S-1133B37-U5T1x Q 9 A
S-1133B13-U5T1x Q 8 C S-1133B38-U5T1x Q 9 B
S-1133B14-U5T1x Q 8 D S-1133B39-U5T1x Q 9 C
S-1133B15-U5T1x Q 8 E S-1133B40-U5T1x Q 9 D
S-1133B16-U5T1x Q 8 F S-1133B41-U5T1x Q 9 E
S-1133B17-U5T1x Q 8 G S-1133B42-U5T1x Q 9 F
S-1133B18-U5T1x Q 8 H S-1133B43-U5T1x Q 9 G
S-1133B19-U5T1x Q 8 I S-1133B44-U5T1x Q 9 H
S-1133B20-U5T1x Q 8 J S-1133B45-U5T1x Q 9 I
S-1133B21-U5T1x Q 8 K S-1133B46-U5T1x Q 9 J
S-1133B22-U5T1x Q 8 L S-1133B47-U5T1x Q 9 K
S-1133B23-U5T1x Q 8 M S-1133B48-U5T1x Q 9 L
S-1133B24-U5T1x Q 8 N S-1133B49-U5T1x Q 9 M
S-1133B25-U5T1x Q 8 O S-1133B50-U5T1x Q 9 N
S-1133B26-U5T1x Q 8 P S-1133B51-U5T1x Q 9 O
S-1133B27-U5T1x Q 8 Q S-1133B52-U5T1x Q 9 P
S-1133B28-U5T1x Q 8 R S-1133B53-U5T1x Q 9 Q
S-1133B29-U5T1x Q 8 S S-1133B54-U5T1x Q 9 R
S-1133B30-U5T1x Q 8 T S-1133B55-U5T1x Q 9 S
S-1133B31-U5T1x Q 8 U S-1133B56-U5T1x Q 9 T
S-1133B32-U5T1x Q 8 V S-1133B57-U5T1x Q 9 U
S-1133B33-U5T1x Q 8 W S-1133B58-U5T1x Q 9 V
S-1133B34-U5T1x Q 8 X S-1133B59-U5T1x Q 9 W
S-1133B35-U5T1x Q 8 Y S-1133B60-U5T1x Q 9 X
Remark 1. x: G or U
2. Please select products of environmental code = U for Sn 100%, halogen-free products.
HIGH RIPPLE-REJECTION AND LOW DROPOUT MIDDLE-OUTPUT CURRENT CMOS VOLTAGE REGULATOR
Rev.3.1_02 S-1133 Series
29
2. SNT-8A
Top view
1432
8567
(1) (2) (3) (4)
(5) (6) (7) (8)
(9) (
10
) (
11
)
(1) Blank
(2) to (4) Product code (Refer to Product name vs. Product code)
(5), (6) Blank
(7) to (11) Lot number
Product name vs. Product code
Product name Product code Product name Product code
(2) (3) (4) (2) (3) (4)
S-1133B00-I8T1U Q 8 A S-1133B36-I8T1U Q 8 Z
S-1133B12-I8T1U Q 8 B S-1133B37-I8T1U Q 9 A
S-1133B13-I8T1U Q 8 C S-1133B38-I8T1U Q 9 B
S-1133B14-I8T1U Q 8 D S-1133B39-I8T1U Q 9 C
S-1133B15-I8T1U Q 8 E S-1133B40-I8T1U Q 9 D
S-1133B16-I8T1U Q 8 F S-1133B41-I8T1U Q 9 E
S-1133B17-I8T1U Q 8 G S-1133B42-I8T1U Q 9 F
S-1133B18-I8T1U Q 8 H S-1133B43-I8T1U Q 9 G
S-1133B19-I8T1U Q 8 I S-1133B44-I8T1U Q 9 H
S-1133B20-I8T1U Q 8 J S-1133B45-I8T1U Q 9 I
S-1133B21-I8T1U Q 8 K S-1133B46-I8T1U Q 9 J
S-1133B22-I8T1U Q 8 L S-1133B47-I8T1U Q 9 K
S-1133B23-I8T1U Q 8 M S-1133B48-I8T1U Q 9 L
S-1133B24-I8T1U Q 8 N S-1133B49-I8T1U Q 9 M
S-1133B25-I8T1U Q 8 O S-1133B50-I8T1U Q 9 N
S-1133B26-I8T1U Q 8 P S-1133B51-I8T1U Q 9 O
S-1133B27-I8T1U Q 8 Q S-1133B52-I8T1U Q 9 P
S-1133B28-I8T1U Q 8 R S-1133B53-I8T1U Q 9 Q
S-1133B29-I8T1U Q 8 S S-1133B54-I8T1U Q 9 R
S-1133B30-I8T1U Q 8 T S-1133B55-I8T1U Q 9 S
S-1133B31-I8T1U Q 8 U S-1133B56-I8T1U Q 9 T
S-1133B32-I8T1U Q 8 V S-1133B57-I8T1U Q 9 U
S-1133B33-I8T1U Q 8 W S-1133B58-I8T1U Q 9 V
S-1133B34-I8T1U Q 8 X S-1133B59-I8T1U Q 9 W
S-1133B35-I8T1U Q 8 Y S-1133B60-I8T1U Q 9 X
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
1.5±0.1 1.5±0.1
1.6±0.2
4.5±0.1
132
1.5±0.1
0.4±0.05
0.4±0.1
0.45±0.1
0.4±0.1
54
SOT895-A-PKG Dimensions
No. UP005-A-P-SD-2.0
UP005-A-P-SD-2.0
45°
0.3
mm
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
2.0±0.1
0.3±0.05
8.0±0.1
ø1.5 +0.1
-0
2.0±0.05
ø1.5 +0.1
-0
4.75±0.1
1
32
54
No. UP005-A-C-SD-2.0
UP005-A-C-SD-2.0
SOT895-A-Carrier Tape
Feed direction
4.0±0.1(10 pitches : 40.0±0.2)
mm
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
16.5max.
13.0±0.3
QTY. 1,000
(60°)
(60°)
No. UP005-A-R-SD-1.1
UP005-A-R-SD-1.1
SOT895-A-Reel
Enlarged drawing in the central part
mm
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
1.5 1.5
0.7
No. UP005-A-L-S1-1.0
UP005-A-L-S1-1.0
SOT895-A
-Land Recommendation
0.7
1.0
2.0
mm
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
1.97±0.03
0.2±0.05
0.48±0.02
0.08
mm
SNT-8A-A-PKG Dimensions
PH008-A-P-SD-2.1
No. PH008-A-P-SD-2.1
0.5
+0.05
-0.02
123 4
56
78
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
mm
PH008-A-C-SD-2.0
SNT-8A-A-Carrier Tape
No. PH008-A-C-SD-2.0
Feed direction
4.0±0.1
2.0±0.05
4.0±0.1
ø1.5 +0.1
-0
ø0.5±0.1
2.25±0.05
0.65±0.05
0.25±0.05
2134
7865
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
12.5max.
9.0±0.3
ø13±0.2
(60°) (60°)
Enlarged drawing in the central part
QTY.
PH008-A-R-SD-1.0
mm
SNT-8A-A-Reel
No. PH008-A-R-SD-1.0
5,000
No.
TITLE
UNIT
ANGLE
ABLIC Inc.
mm
SNT-8A-A
-Land Recommendation
PH008-A-L-SD-4.1
0.3
0.2
0.52
2.01
0.52
No. PH008-A-L-SD-4.1
Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package.
2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm
or less from the land pattern surface.
3. Match the mask aperture size and aperture position with the land pattern.
4. Refer to "SNT Package User's Guide" for details.
1. (0.25 mm min. / 0.30 mm typ.)
2. (1.96 mm ~ 2.06 mm)
1.
2. 0.03 mm
3.
4. SNT
1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.).
2. Do not widen the land pattern to the center of the package (1.96 mm to 2.06mm).
1
2
1.
2. (1.96 mm ~ 2.06 mm)
(0.25 mm min. / 0.30 mm typ.)
Disclaimers (Handling Precautions)
1. All the information described herein
(product data,
specifications,
figures,
tables,
programs,
algorithms and application
circuit examples,
etc.)
is current as of publishing date of this document and is subject to change without notice.
2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not responsible for damages caused by the reasons other than the products described herein
(hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use
of the information described herein.
3. ABLIC Inc. is not responsible for damages caused by the incorrect information described herein.
4. Be careful to use the products within their specified ranges. Pay special attention to the absolute maximum ratings,
operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not responsible for damages caused by failures and / or accidents, etc. that occur due to the use of the
products outside their specified ranges.
5. When using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7. The products must not be used or provided (exported) for the purposes of the development of weapons of mass
destruction or military use. ABLIC Inc. is not responsible for any provision (export) to those whose purpose is to
develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use.
8. The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do
not apply the products to the above listed devices and equipments without prior written permission by ABLIC Inc.
Especially, the products cannot be used for life support devices, devices implanted in the human body and devices
that directly affect human life, etc.
Prior consultation with our sales office is required when considering the above uses.
ABLIC Inc. is not responsible for damages caused by unauthorized or unspecified use of our products.
9. Semiconductor products may fail or malfunction with some probability.
The user of the products should therefore take responsibility to give thorough consideration to safety design including
redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or
death, fires and social damage, etc. that may ensue from the products' failure or malfunction.
The entire system must be sufficiently evaluated and applied on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc.
The information described herein does not convey any license under any intellectual property rights or any other
rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any
part of this document described herein for the purpose of disclosing it to a third-party without the express permission
of ABLIC Inc. is strictly prohibited.
14. For more details on the information described herein, contact our sales office.
2.2-2018.06
www.ablic.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ABLIC:
S-1133B00-I8T1G S-1133B12-I8T1G S-1133B13-I8T1G S-1133B14-I8T1G S-1133B15-I8T1G S-1133B16-I8T1G
S-1133B17-I8T1G S-1133B18-I8T1G S-1133B19-I8T1G S-1133B20-I8T1G S-1133B21-I8T1G S-1133B22-I8T1G S-
1133B23-I8T1G S-1133B24-I8T1G S-1133B25-I8T1G S-1133B26-I8T1G S-1133B27-I8T1G S-1133B28-I8T1G S-
1133B29-I8T1G S-1133B30-I8T1G S-1133B31-I8T1G S-1133B32-I8T1G S-1133B33-I8T1G S-1133B34-I8T1G S-
1133B35-I8T1G S-1133B36-I8T1G S-1133B37-I8T1G S-1133B38-I8T1G S-1133B39-I8T1G S-1133B40-I8T1G S-
1133B41-I8T1G S-1133B42-I8T1G S-1133B43-I8T1G S-1133B44-I8T1G S-1133B45-I8T1G S-1133B46-I8T1G S-
1133B47-I8T1G S-1133B48-I8T1G S-1133B49-I8T1G S-1133B50-I8T1G S-1133B51-I8T1G S-1133B52-I8T1G S-
1133B53-I8T1G S-1133B54-I8T1G S-1133B55-I8T1G S-1133B56-I8T1G S-1133B57-I8T1G S-1133B58-I8T1G S-
1133B59-I8T1G S-1133B60-I8T1G S-1133B26-I8T1U S-1133B12-U5T1U
