Datasheet Multi-function LCD Segment Drivers BU97981xxx Series MAX 196 Segments (SEG49xCOM4) Features Integrated RAM for Display Data (DDRAM): 49 x4 Bit (Max 196 Segment) LCD Drive Output: 4 Common Output, Max 49 Segment Output Integrated 3ch LED Driver Circuit Segment/ LED (Max 3port) Output Mode Selectable Segment/ GPO (Max 31port) Output Mode Selectable Support PWM Generation from Ext. or Internal Clock (Resolution: 8bit Mode/12bit Mode Selectable) Support Standby Mode Integrated Power-on-Reset Circuit (POR) Integrated Oscillator Circuit No External Component Low Power Consumption Design Independent Power Supply for LCD Driving Support Blink Function (Blink Frequency 1.6, 2.0, 2.6, 4.0Hz selectable) Key Specifications Supply Voltage Range: +1.8V to +3.6V LCD Drive Power Supply Range: +3.3V to +5.5V Operating Temperature Range: -30C to +75C Max Segments: BU97981KV 196 Segments BU97981MUV 168 Segments BU97981GU 196 Segments Max GPO Outputs: BU97981KV 31port BU97981MUV 27port BU97981GU 31port Max LED Drive Outputs: BU97981KV 3port BU97981MUV 3port BU97981GU 3port Display Duty: Static. 1/3, 1/4 Selectable Bias: Static, 1/3 Integrated Regulator for LCD Drive: 3.2, 3.3, 3.4, 4.4, 4.5, 4.6, 5.0V Selectable Interface: 3wire Serial Interface Applications Telephone FAX Portable Equipment (POS, ECR, PDA etc.) DSC DVC Car audio Home Electrical Appliance Meter Equipment etc. Typical Application Circuit BU97981KV LED/GPO using case LED : 3port GPO : 5port LCD :164seg VLED *Reading resistor value Please detect the value according to inpu curremt value. (cuurent MAX = 20mA) VLCD SEG48 (LED1) SEG47 (LED2) SEG46 (LED3) VDD BU97981KV 5.0V SEG45(GPO1) to SEG41(GPO5) 3.3V VSS1 VSS2 TEST1 CSB SCL SD Other device SEG0 to SEG40 INHb CLKIN Input signal from cintroller COM0 to COM3 LCD CLKIN Extenal CLK input terminal In case being unused, connect to VSS or be opened. Figure 1. Typical Application Circuit Product structureSilicon monolithic integrated circuit www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211114001 This product has no designed protection against radioactive rays. 1/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Block Diagram / Pin Arrangement / Pin Description SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG35 COM0......COM3 SEG0 .................................... SEG48 VSS2 SEG34 BU97981KV common driver Segment driver Segment Segment driver/GPO driver/LED 49 Ref Voltage Circuit Vreg GPO/LED Controller LCD BIAS SELECTOR common counter blink timing generator DDRAM GPO data latch PWM Generator VSS INHb CLKIN 33 LCD voltage Generator 48 VLCD Command register Data Decoder OSCILLATOR Power On Reset 32 SEG36 SEG19 SEG37 SEG18 SEG38 SEG17 SEG39 SEG16 SEG40 SEG15 SEG41 SEG14 SEG42 SEG13 SEG43 SEG12 SEG44 SEG11 SEG45 SEG10 SEG46 SEG9 SEG47 SEG8 SEG48 SEG7 VSS2 SEG6 PWMOUT serial inter face SEG5 CLKIN SD SCL PWMOUT Figure 2. Block Diagram SEG3 SEG2 SEG1 SEG0 COM3 COM2 COM1 COM0 VLCD INHb VSS1 VDD TEST1 CSB SD TEST1 SCL CSB 1 IF FILTER VSS 17 16 VDD SEG4 64 Output Controller Figure 3. Pin Configuration (TOP VIEW) Table 1. Pin Description Terminal Terminal number I/O Unused case CSB 1 I - Chip select: "L" active SCL 2 I - Serial data transfer clock Function SD 3 I - Input serial data VDD 4 - - CLKIN 64 I OPEN / VSS TEST1 5 I - Power supply for LOGIC External clock input terminal (for display/PWM using selectable) Support Hi-Z input mode at internal clock mode TEST terminal (Please connect VSS terminal) VSS1 6 - - GND VLCD 8 - - Power supply for LCD Display turning on/off select terminal H: turning on display, L: turning off display INHb 7 I VDD INHb = "L": All SEG/COM terminal : output VSS level GPO terminal : output VSS level LED drive terminal : output Hi-Z PWMOUT 63 O OPEN PWM output for LED2 group COM0 to 3 9 to 12 O OPEN COMMON output for LCD SEG0 to 14 13 to 27 O OPEN SEGMENT output for LCD SEG15 to 45 28 to 58 O OPEN SEGMENT output for LCD/GPO SEG46 to 48 59 to 61 O OPEN SEGMENT output for LCD/LED driver VSS2 62 - GND www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 GND (for SEG46-48 / LED driver) 2/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Block Diagram / Pin Arrangement / Pin Description DDRAM GPO data latch Blink timing generator Common counter PWM Generator VSS INHb Clock Divider (div.2) CR oscillator (typ:40.96KHz) CLKIN Command register Data Decode Power On Reset Serial inter face OSC block VDD Output Controller IF FILTER SCL COM1 COM2 COM3 SEG0 10 11 12 13 14 SEG1 COM0 9 16 SEG3 54 17 SEG4 SEG2 SEG40 53 18 SEG5 SEG39 SEG38 SEG37 52 19 51 20 SEG6 SEG7 SEG8 SEG36 SEG35 49 22 48 23 SEG34 SEG33 SEG32 47 24 46 25 EXT-PAD 50 21 SEG9 SEG10 45 26 SEG11 SEG12 SEG13 SEG31 44 27 SEG14 SEG30 43 28 SEG15 PWMOUT Figure 4. Block Diagram 8 15 41 40 SEG29 SEG28 SEG27 SD 7 55 42 CSB 6 5 VSS2 SEG41 VSS TEST1 4 39 38 37 36 35 34 33 32 31 30 29 SEG16 LCD BIAS SELECTOR 3 56 SEG21 SEG20 SEG19 SEG18 SEG17 GPO / LED Controller 2 VSS1 INHb VLCD 1 CLKIN SEG23 SEG22 Vreg Segment Driver/ LED SEG25 SEG24 Segment Driver/ GPO SEG26 Ref Voltage Circuit Segment Driver Common Driver LCD voltage Generator VDD TEST1 COM0 ....COM3 SEG0 ..................................SEG48 COM0......COM 3 CSB SCL VSS2 VLCD SD BU97981MUV Figure 5. Pin Configuration (BOTTOM VIEW) Table 2. Pin Description CSB Terminal number 1 SCL 2 Terminal I/O Unused case Function I - Chip select: "L" active I - Serial data transfer clock SD 3 I - Input serial data VDD 4 - - CLKIN 56 I OPEN / VSS TEST1 5 I - Power supply for LOGIC External clock input terminal (for display/PWM using selectable) Support Hi-Z input mode at internal clock mode TEST terminal (Please connect VSS terminal) VSS1 6 - - GND VLCD 8 - - Power supply for LCD Display turning on/off select terminal H: turning on display, L: turning off display INHb 7 I VDD INHb = "L": All SEG/COM terminal : output VSS level GPO terminal : output VSS level LED drive terminal : output Hi-Z COM0~3 9-12 O OPEN COMMON output for LCD SEG0~11 13-24 O OPEN SEGMENT output for LCD SEG12~38 25-51 O OPEN SEGMENT output for LCD/GPO SEG39~41 52-54 O OPEN SEGMENT output for LCD/LED driver VSS2 55 - GND GND (for SEG39-41 / LED driver) (Note1) EXT-PAD VSS substrate (Note1) To radiate heat, please contact a board with the EXT-PAD which is located at the bottom side of VQFN56AV8080 package. Please supply VSS level or Open state as the input condition for this PAD. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 3/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Block Diagram / Pin Arrangement / Pin Description BU97981GU COM0......COM3 SEG0 .................................... SEG48 VSS2 1 2 H SEG4 SEG5 SEG9 SEG11 SEG14 SEG16 SEG18 SEG20 G SEG2 SEG3 SEG7 F SEG0 SEG1 SEG6 SEG10 SEG13 SEG22 SEG23 SEG25 E COM2 COM0 COM1 COM3 SEG15 SEG26 SEG24 SEG27 D VLCD VDD INHB SEG47 SEG31 SEG29 SEG28 SEG30 C VSS1 SDA SCL B (NC) CLKIN A CSB VLCD LCD voltage Generator common driver Segment driver Segment Segment driver/GPO driver/LED 3 4 5 6 7 8 Ref Voltage Circuit Vreg GPO/LED Controller LCD BIAS SELECTOR common counter blink timing generator DDRAM GPO data latch SEG8 SEG12 SEG17 SEG19 SEG21 PWM Generator VSS INHb CLKIN Command register Data Decoder OSCILLATOR Power On Reset SEG45 SEG42 SEG38 SEG33 SEG32 serial inter face Output Controller VDD VSS2 SEG44 SEG40 SEG39 SEG35 SEG34 IF FILTER VSS CSB SD SCL PWMOUT Figure 6. Block Diagram PWM OUT SEG48 SEG46 SEG43 SEG41 SEG37 SEG36 Figure 7. Pin Configuration (TOP VIEW) Table 3. Pin Description Terminal I/O Unused case Function CSB I - Chip select: "L" active SCL I - Serial data transfer clock SD I - Input serial data VDD - - Power supply for LOGIC CLKIN I OPEN / VSS VSS1 - - GND VLCD - - Power supply for LCD External clock input terminal (for display/PWM using selectable) Support Hi-Z input mode at internal clock mode Display turning on/off select terminal H: turning on display, L: turning off display INHb I VDD INHb = "L": All SEG/COM terminal : output VSS level GPO terminal : output VSS level LED drive terminal : output Hi-Z PWMOUT O OPEN PWM output for LED2 group COM0 to 3 O OPEN COMMON output for LCD SEG0 to 14 O OPEN SEGMENT output for LCD SEG15 to 45 O OPEN SEGMENT output for LCD/GPO SEG46 to 48 O OPEN SEGMENT output for LCD/LED driver VSS2 - GND www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 GND (for SEG46-48 / LED driver) 4/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Absolute Maximum Ratings (VSS=0V) Parameter Symbol Ratings Unit Power Supply Voltage 1 VDD -0.3 to +4.5 V Power supply Power Supply Voltage 2 VLCD -0.5 to +7.0 V Power supply for LCD Power Dissipation Pd Input Voltage Range VIN Operational Temperature Range Storage Temperature Range Output Current 1.0 (Note1) 3.6 (Note2) 0.8 (Note3) Remarks BU97981KV W BU97981MUV BU97981GU -0.5 to VDD+0.5 V Topr -30 to +75 C Tstg -55 to +125 C Iout1 5 mA SEG output Iout2 5 mA COM output Iout3 10 mA GPO output Iout4 50 mA LED output (Note1) When use more than Ta=25C, subtract 10mW per degree. (using ROHM standard board) (board size70mmx70mmx1.6mm material: FR4 board copper foil: land pattern only). (Note2) When use more than Ta=25C, subtract 36mW per degree. (using ROHM standard board) (board size74.2mmx74.2mmx1.6mm SEMI standard 4 layer board) (Note3) When operated higher than Ta=25C, subtract 8.0mW per degree. (using ROHM standard board) (board size114.3mmx76.2mmx1.6mm) Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. Recommended Operating Conditions (Ta=-30C to +75C,VSS=0V) Parameter Symbol Power Supply Voltage 1 Ratings Unit Remarks Min Typ Max VDD 1.8 - 3.6 V Power supply Power Supply Voltage 2 VLCD 3.3 - 5.5 V Power supply for LCD LED Supply Voltage VLED 1.0 - VLCD V Power supply for LED Iout4 - - 20 mA Per LED port 1ch Iout4 - - 60 mA Total LED port current Output Current www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 5/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Electrical Characteristics DC characteristics (Ta=-30C to +75C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0) (BU97981KV,BU97981GU) Limits Parameter Symbol Unit Min Typ Max Conditions "H" level Input Voltage VIH 0.8VDD - VDD V SD, SCL, CSB, TEST1 (Note4) ,CLKIN, INHb "L" level Input Voltage VIL VSS - 0.2VDD V SD, SCL, CSB, TEST1 (Note4) ,CLKIN, INHb Hysteresis Width VH - 0.2 - V "H" Level Input Current IIH1 - - 5 A "L" Level Input Current IIL1 -5 - - A VOH1 VLCD -0.4 - - V VOH2 VLCD -0.4 - - V VOH3 VLCD -0.6 - - V SCL, INHb, VDD=3.3V, Ta=25C SD, SCL, CSB, CLKIN, INHb, VI=3.6V (Note4) SD, SCL, CSB, CLKIN, INHb, TEST1 , VI=0V Iload=-50A, VLCD=5.0V SEG0 to SEG48, Unused integrated regulator Iload=-50A, VLCD=5.0V, COM0 to COM3, Unused integrated regulator Iload=-1mA,VLCD=5.0V, SEG15 to SEG45 (GPO mode) Unused integrated regulator - - V Iload=-1mA, VDD=3.0V, PWMOUT - 0.4 V Iload= 50A, VLCD=5.0V, SEG0 to SEG48 Iload= 50A, VLCD=5.0V, COM0 to COM3 Iload=1mA, VLCD=5.0V, SEG15 to SEG45 (GPO mode), PWMOUT Iload=20mA, VLCD=5.0V, SEG46 to 48 (LED drive mode) Input terminal ALLL, Display off, Oscillation off Input terminal ALLL, Display off, Oscillation off VDD=3.3V, Ta=25 C, 1/3bias, fFR=64Hz, PWM generate off, All output pin open VDD=3.3V, Ta=25 C, 1/3bias, fFR=64Hz, PWM Frequency=500Hz setting, All output pin open VLCD=5.0V, Ta=25 C, 1/3bias, fFR=64Hz, Unused Integrated regulator, LED generate off, All output pin open VLCD=5.0V, Ta=25 C, 1/3bias, fFR=64Hz, Used Integrated regulator, LED generate off, All output pin open VLCD=5.0V, Ta=25 C,1/3bias, fFR=64Hz, Used Integrated regulator, PWM Frequency=500Hz setting, All output pin open "H" Level Output Voltage (Note1&3) VOL1 VDD -0.6 - VOL2 - - 0.4 V VOL3 - - 0.5 V VOL4 - 0.11 0.5 V IstVDD - 3 10 A IstVLCD - 0.5 5 A IVDD1 - 8 15 A IVDD2 - 90 130 A IVLCD1 - 10 15 A IVLCD2 - 25 40 A IVLCD3 - 30 48 A VOH4 "L" Level Output Voltage Current Consumption (Note3) (Note2) (Note1) Integrated regulator using case, please add load regulation value to output voltage listed above. (Note2) Power save mode 1 and frame inversion setting (Note3) Iload: In case, load current from only one port (Note4) There is not TEST1 port in BU97981GU www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 6/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Electrical Characteristics - Continued DC characteristics (Ta=-30C to +75C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0) (BU97981MUV) Limits Parameter Symbol Unit Min Typ Max Conditions "H" level Input Voltage VIH 0.8VDD - VDD V SD, SCL, CSB, TEST1,CLKIN, INHb "L" level Input Voltage VIL VSS - 0.2VDD V SD, SCL, CSB, TEST1,CLKIN, INHb Hysteresis Width VH - 0.2 - V "H" level Input Current IIH1 - - 5 A "L" level Input Current IIL1 -5 - - A VOH1 VLCD -0.4 - - V VOH2 VLCD -0.4 - - V VOH3 VLCD -0.6 - - V VOL1 - - 0.4 V SCL, INHb, VDD=3.3V, Ta=25C SD, SCL, CSB, CLKIN, INHb, VI=3.6V SD, SCL, CSB, CLKIN, INHb, TEST1, VI=0V Iload=-50A, VLCD=5.0V SEG0 to SEG41, Unused integrated regulator Iload=-50A, VLCD=5.0V, COM0 to COM3, Unused integrated regulator Iload=-1mA,VLCD=5.0V, SEG12 to SEG38 (GPO mode) Unused integrated regulator Iload= 50A, VLCD=5.0V, SEG0 to SEG41 VOL2 - - 0.4 V VOL3 - - 0.5 V VOL4 - 0.11 0.5 V IstVDD - 3 10 A IstVLCD - 0.5 5 A IVDD1 - 8 15 A IVDD2 - 90 130 A IVLCD1 - 10 15 A IVLCD2 - 25 40 A IVLCD3 - 30 48 A "H" Level Output Voltage (Note1&3) "L" Level Output Voltage Current Consumption (Note3) (Note2) Iload= 50A, VLCD=5.0V, COM0 to COM3 Iload=1mA, VLCD=5.0V, SEG12 to SEG38 (GPO mode), PWMOUT Iload=20mA, VLCD=5.0V, SEG39 to SEG41 (LED drive mode) Input terminal ALLL, Display off, Oscillation off Input terminal ALLL, Display off, Oscillation off VDD=3.3V, Ta=25 C, 1/3bias, fFR=64Hz, PWM generate off, All output pin open VDD=3.3V, Ta=25 C, 1/3bias, fFR=64Hz, PWM Frequency=500Hz setting, All output pin open VLCD=5.0V, Ta=25 C, 1/3bias, fFR=64Hz, Unused Integrated regulator, LED generate off, All output pin open VLCD=5.0V, Ta=25 C, 1/3bias, fFR=64Hz, Used Integrated regulator, LED generate off, All output pin open VLCD=5.0V, Ta=25 C,1/3bias, fFR=64Hz, Used Integrated regulator, PWM Frequency=500Hz setting, All output pin open (Note1) Integrated regulator using case, please add load regulation value to output voltage listed above. (Note2) Power save mode 1 and frame inversion setting (Note3) Iload: In case, load current from only one port www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 7/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Electrical Characteristics - continued Integrated Regulator Characteristics (Ta=-30C to +75C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0) (BU97981KV) Limits Parameter Symbol Unit Conditions Min Typ Max 4.5V setting (VLCD=5.5V, Ta=-30C to 75C) Output Voltage 1 Vreg1 4.35 4.5 4.65 V (Note1) Output Voltage 2 Load Regulation (Note2) Vreg2 delta Vreg 4.42 4.5 4.58 V 4.5V setting (VLCD=5.5V, Ta=25C) - - 0.3 V Iout = -300A (Note1) (Note1)In case integrated regulator using, please satisfy condition that Vreg output lower than VLCD - 0.5V. (Note2) Load regulation: Vreg block load regulation only. Do not include other block ability. (BU97981MUV) Parameter Symbol Limits Min Typ Max Unit Conditions 4.5V setting (VLCD=5.5V, Ta=-30C to 75C) Output Voltage 1 Vreg1 4.30 4.5 4.70 V Output Voltage 2 Vreg2 delta Vreg 4.38 4.5 4.62 V 4.5V setting (VLCD=5.5V, Ta=25C) - - 0.3 V Iout = -300A Load Regulation (Note2) (Note1) (Note1) (Note1)n case integrated regulator using, please satisfy condition that Vreg output lower than VLCD - 0.5V. (Note2) Load regulation: Vreg block load regulation only. Do not include other block ability. (BU97981GU) Parameter Symbol Limits Min Typ Max Unit Conditions 4.5V setting (VLCD=5.5V, Ta=-30C to 75C) Output Voltage 1 Vreg1 4.25 4.5 4.70 V Output Voltage 2 Vreg2 delta Vreg 4.40 4.5 4.60 V 4.5V setting (VLCD=5.5V, Ta=25C) - - 0.3 V Iout = -300A Load Regulation (Note2) (Note1) (Note1) (Note1)In case integrated regulator using, please satisfy condition that Vreg output lower than VLCD - 0.5V. (Note2) Load regulation: Vreg block load regulation only. Do not include other block ability. Oscillation Frequency Characteristics (Ta=-30C to +75 C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0) Limits Parameter Symbol Unit Conditions Min Typ Max Frame Frequency 1 fFR1 57.6 64 70.4 Hz VDD=3.3V, Ta=25C, fFR=64Hz setting Frame Frequency 2 fFR2 51.2 64 73.0 Hz VDD=2.5V to 3.6V fFR=64Hz setting Frame Frequency 3 fFR3 45.0 - 64 Hz VDD=1.8V to 2.5V fFR=64Hz setting CLKIN Input Frequency fCLK - 2 4 MHz About detail function, please refer to the frame frequency setting of DISCTL command. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 8/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) MPU Interface Characteristics (Ta=-30C to +75 C, VDD=1.8V to 3.6V, VLCD=3.3V to 5.5V, VSS=0) Limits Parameter Symbol Unit Conditions Min Typ Max Input Rise Time tr Input Fall Time - - 50 ns tf - - 50 ns SCL Cycle Time tSCYC 250 - - ns "H" SCL Pulse Width tSHW 50 - - ns "L" SCL Pulse Width tSLW 50 - - ns SD Setup Time tSDS 50 - - ns SD Hold Time tSDH 50 - - ns CSB Setup Time tCSS 50 - - ns CSB Hold Time tCSH 50 - - ns "H" CSB Pulse Width tCHW 50 - - ns tCHW CSB tCSH tCSS tr tf SCL tSCYC tSLW tSHW tSDS tSDH SD Figure 8. Serial Interface Timing www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 9/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet I/O Equivalence Circuit (BU97981KV) VLCD VDD VSS1 VSS1 VDD TEST1 VDD VSS CSB, SD, SCL,INHb CLKIN VDD PWMOUT VSS VSS1 VDD VLCD SEG0-14 COM0-3 SEG15-45 VSS1 VSS1 VLCD SEG46-48 VSS2 VSS1 Figure 9. I/O Equivalence Circuit www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 10/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet I/O Equivalence Circuit - Continued (BU97981MUV) VLCD VDD VSS1 VSS1 VDD VDD TEST1 VSS CSB, SD, SCL,INHb CLKIN VSS VDD VLCD SEG0-11 COM0-3 SEG12-38 VSS1 VSS1 VLCD SEG39-41 VSS2 VSS1 Figure 10. I/O Equivalence Circuit www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 11/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet I/O Equivalence Circuit - Continued (BU97981GU) VLCD VDD VSS1 VSS1 VDD VDD PWMOUT VSS1 CSB, SD, SCL,INHb CLKIN VDD VSS SEG0-14 COM0-3 VSS1 VLCD VLCD SEG15-45 SEG46-48 VSS1 VSS2 VSS1 Figure 11. I/O Equivalence Circuit www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 12/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Example of Recommended Circuit (BU97981KV) 1. LED/GPO Using Case [LED]&[GPO] LED 3port GPO 5port LCD 164segments VLED Regarding resistor value Please detect the value according to input current value. (current MAX = 20mA) VLCD SEG48 (LED1) SEG47 (LED2) SEG46 (LED3) VDD BU97981KV 5.0V 3.3V VSS1 VSS2 TEST1 CSB SCL SD Other device SEG45(GPO1) SEG41(GPO5) SEG0SEG40 INHb CLKIN LCD COM0COM3 CLKIN External CLK input terminal Input signal from controller In case being unused, connect to VSS. 2. SEG Output Only Case VLCD VDD BU97981KV 5.0V 3.3V VSS1 VSS2 TEST1 CSB SCL SD SEG0SEG48 INHb CLKIN COM0COM3 LCD CLKIN External CLK input teminal Input signal from controller In case being unused, connect to VSS. Figure 12. BU97981KV www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 E.g. of Recommended Circuit 13/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Example of Recommended Circuit - Continued (BU97981MUV) 1. LED/GPO Using Case LED 3port GPO 5port LCD 136segments VLED Regarding resistor value Please detect the value according to input current value. (current MAX = 20mA) VLCD SEG39 (LED1) SEG40 (LED2) SEG41 (LED3) VDD BU97981MUV 5.0V Other device SEG38(GPO1) SEG34(GPO5) 3.3V VSS1 VSS2 TEST1 CSB SCL SD INHb CLKIN Input signal from controller SEG0SEG33 LCD COM0COM3 CLKIN External CLK input terminal In case being unused, connect to VSS. 2. SEG Output Only Case VLCD VDD BU97981MUV 5.0V 3.3V VSS1 VSS2 TEST1 CSB SCL SD SEG0SEG41 INHb CLKIN Input signal from controller Figure 13. BU97981MUV www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 LCD COM0COM3 CLKIN External CLK input teminal In case being unused, connect to VSS. E.g. of Recommended Circuit 14/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Example of Recommended Circuit - Continued (BU97981GU) 1. LED/GPO Using Case LED 3port GPO 5port LCD 164segments VLED Regarding resistor value Please detect the value according to input current value. (current MAX = 20mA) VLCD SEG48 (LED1) SEG47 (LED2) SEG46 (LED3) VDD BU97981GU 5.0V Other device SEG45(GPO1) SEG41(GPO5) 3.3V VSS1 VSS2 SEG0SEG40 CSB SCL SD INHb CLKIN Input signal from controller LCD COM0COM3 CLKIN External CLK input terminal In case being unused, connect to VSS. 2. SEG Output Only Case VLCD VDD BU97981GU 5.0V 3.3V VSS1 VSS2 SEG0SEG48 CSB SCL SD INHb CLKIN LCD COM0COM3 CLKIN External CLK input teminal In case being unused, connect to VSS. Input signal from controller Figure 14. BU97981GU www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 E.g. of Recommended Circuit 15/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Function Descriptions Command and Data Transfer Method 3-SPI (3 wire serial interface) This device is controlled by 3-wire signal (CSB, SCL, and SD). First, Interface counter is initialized with CSB="H", and CSB="L" makes SD and SCL input enable. The protocol of 3-SPI transfer is as follows. Each command starts with Command or Data judgment bit (D/C) as MSB data, and continuously in order of D6 to D0 are followed after CSB ="L". th (Internal data is latched at the rising edge of SCL, it converted to 8bits parallel data at the falling edge of 8 CLK.) When CSB rise from "L" to "H", and at this time sending commands are less than 8bit, command and data transfer are canceled. To start sending command again, please fall CSB="L" and send command continuously. After sending RAMWR or BLKWR or GPOSET command, BU97981KV/MUV is in the RAM data input mode. Under this mode, device can not accept new commands. In this case, please rise CSB="H" and fall CSB="L", after this sequence device released from RAM data input mode, and can accept new command. 1st byte Command 2nd byte Command 3rd byte Command CSB SCL SD D/C D6 D5 D4 D3 D2 D1 D0 D/C D6 D5 D4 D3 D2 D1 D0 D/C D6 D5 D4 D3 D2 D1 D0 D/C D6 Figure 15. 3-SPI Data Transfer Format 8bit data, sending after RAMWR command, are display RAM data 8bit data, sending after BLKWR command, are blink RAM data SCL and SD can be set to "H" or cleared to "L" during CSB="H" www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 16/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Write Display Data and Transfer Method This device has Display Data RAM (DDRAM) of 49x4=196bit. The relationship between data input and display data, DDRAM data and address are as follows. 1st Byte 2nd Byte Command Command Command 10000011 00000000 10100000 a b d e f g h i j k l m n o p ... Display RAM data RAM Write Address set c According to this command, 8bit binary data will write to DDRAM. The address which starts data writing is specified by "ADSET" command, and increment after finish writing display data every 4 bit. It is able to write to DDRAM by continuously sending data. (In case data is sent continuously after write date at 30h (KV: SEG48), RAM data will be written to 31h (dummy address) and return to address 00h (SEG0) automatically.) In case, SEG port assigned to GPO or LED port by OUTSET1 command, corresponding SEG address do not change and used as dummy address. (BU97981KV,BU97981GU) DDRAM address 01 02 03 0 a e i m 1 b f j n 2 c g k o 3 d h l p SEG 0 SEG 1 SEG 2 SEG 3 04 05 06 07 2Fh SEG 4 SEG 5 SEG 6 SEG 7 .... SEG 47 (BU97981MUV) BIT 01 02 03 0 a e i m 1 b f j n 2 c g k o 3 d h l p SEG 0 SEG 1 SEG 2 SEG 3 31h 04 29 COM0 COM1 COM2 COM3 SEG 48 Dummy data DDRAM address 00 30h DUMMY ADDRESS BIT 00 2A 2Fh 30h 31h COM0 DUMMY ADDRESS COM1 COM2 COM3 SEG 4 SEG 41 Display data write to DDRAM every 4bits. In case CSB change from "L" to "H" before 4bits data transfer finish, RAM write is canceled. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 17/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) 1st byte Command / 2nd byte Command Display data Command CSB SCL SD RAMWR command Address set command D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Internal Signal RAM write Address 00h Address 01h Address 02h data lower than 4bit case RAM write is canceled RAM write every 4bit 1st byte Command / 2nd byte Command Display data Command CSB SCL SD D7 RAMWR command Address set command D6 D5 D4 D3 D2 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 Internal Signal RAM write Address 00h Address 30h Address 31h Addres00h Auto increment Return to address 00h Figure 16. Display Data Transfer Method Blink Function This device has Blink function. Blink function is able to set each segment port individually. Blink ON/OFF and Blink frequency are set by the BLKSET command. Blink frequency varies, according to fCLK characteristics. Blink setup of each segments are controlled by BLKWR command. The write start address is specified by "BLKADSET" command. And this address will increment after finish writing blink data every 4 bit. The relation of BLKWR command, blink ram data, and blinking segment port is below. In case of data is "1", segment will blink, on the other hand data is "0", do not blink. (In case data is written continuously, after write date at 30h (KV: SEG48), ram data will be written to 31h (dummy address) and return to address 00h (SEG0) automatically.) Please refer to following figure about Blink operation of each segment. In case, SEG port assigned to GPO or LED port by OUTSET1 command, corresponding SEG address do not change and used as dummy address. 1st Byte 2nd Byte Command Command 10000100 00000011 Blink set 1st Byte 2nd Byte Command Command Command 00000000 11000000 10000111 Blink Address set www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Blink RAMWR 18/46 a b c d e f g h i j k l m n o p ... Blink RAM data TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) (BU97981KV,BU97981GU) Blink RAM Address 01 02 03 0 A e i m 1 B f j n 2 C g k o 3 D h l p SEG 0 SEG 1 SEG 2 SEG 3 04 05 06 07 2Fh SEG 4 SEG 5 SEG 6 SEG 7 SEG 47 (BU97981MUV) BIT 01 02 03 0 a e i m 1 b f j n 2 c g k o 3 d h l p SEG 0 SEG 1 SEG 2 SEG 3 31h 04 29 2A COM0 COM1 COM2 COM3 SEG 48 Dummy data Blink RAM Address 00 30h DUMMY ADDRESS BIT 00 2Fh 30h 31h COM0 COM1 DUMMY ADDRESS COM2 COM3 SEG 4 SEG 41 DDRAM data SEG A SEG B SEG C SEG D SEG A SEG B SEG C SEG D SEG A SEG B SEG C SEG D Blink RAM data Segment output SEG A SEG B SEG C SEG D SEG A Blink frequency under the 2Hz stting segment output will blink every 0.5 second (ON->OFF->ON) SEG B SEG C SEG D SEG A SEG B SEG C SEG D SEGA/B is blink Figure 17. Blink Operation www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 19/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) LCD Driver Bias/Duty Circuit This LSI generates LCD driving voltage with on-chip Buffer AMP. And it can drive LCD at low power consumption Line and frame inversion can be set in MODESET command. 1/4duty, 1/3duty and static mode can be set DISCTL command. About each LCD driving waveform, please refer to "LCD driving waveform" descriptions. Initial state Initial state, after Software Reset command input 1. Display off 2. All command register value set Reset state. 3. DDRAM address data and Blink address data are initializing (DDRAM data and Blink RAM data are not initializing. Please write DDRAM data and Blink RAM data before Display on.) Command / Function list Function Description Table NO Command Function 1 Mode Set 2 Display control (DISCTL) Set LCD drive mode (frame freq., line/frame inversion) 3 Address set (ADSET) Set display data RAM address for RAMWR command 4 Blink set (BLKSET) Set Blink mode on/off 5 Blink address set (BLKADSET) Set Blink data RAM address for BLKWR command 6 7 8 9 (MODESET) Set LCD drive mode (display on/off, current mode) SEG/GPO port change (OUTSET1) SEG/LED port change (OUTSET2) LED1 drive control (PWM1SET) (H piece adjustment of PWM1) LED2-3 drive control (PWM2SET) (H piece adjustment of PWM2) Select segment output/general purpose output (GPO) Select segment output/LED driving output Set PWM1 signal "H" width for LED1 driving Set PWM2 signal "H" width for LED2-3 driving 10 Display data RAM WRITE (RAMWR) Write display data to display data RAM 11 Blink RAM WRITE (BLKWR) Write Blink data to BLINK data RAM 12 All Pixel ON (APON) Set all Pixel display on 13 All Pixel OFF (APOFF) Set all Pixel display off 14 All Pixel On/Off mode off (NORON) Set normal display mode (APON/APOFF cancel) 15 Software Reset (SWRST) Software Reset 16 OSC external input (OSCSET) Set External clock input 17 Integrated Regulator setup (REGSET) Set integrated regulator voltage output 18 GPO output set (GPOSET) Set GPO output data www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 20/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Command Detail Descriptions D/C, Data / Command judgment bit (MSB) Detail, please refer to 3wire serial I/F Mode Set (MODESET) MSB D/C D6 st 1 byte command 2 nd byte command D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 0 0 0 1 81h - 0 0 0 0 P3 P2 P1 P0 - 00h Display Set Condition Display OFF P3 Reset state 0 Display ON 1 Display OFF : No LCD driving mode (Output: VSS Level) Turn off OSC circuit and LCD power supply circuit. (Synchronized with frame freq) Display ON : LCD driving mode Turn on OSC circuit and LCD power supply circuit. Read data from DDRAM and display to LCD. LED port and GPO port output state are not influenced by a Display on/off state Output state is decided by command setup (GPOSET, OUTSET1, OUTSET2, PWM1SET, PWM2SET) and INHb terminal state. About detail, please refer to each command description. LCD drive mode set Condition P2 Reset state Frame inversion 0 Line inversion 1 Current mode set Condition P1 P0 Reset state Power save mode1 0 0 Power save mode2 0 1 Normal mode 1 0 High power mode 1 1 (Reference data of consumption current) Condition Current consumption Power save mode 1 x1.0 Power save mode 2 x1.7 Normal mode x2.7 High power mode x5.0 The value changes according to the panel load. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 21/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Display Control (DISCTL) st 1 byte Command 2 nd byte Command Duty Set Condition MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 0 0 1 0 82h - 0 0 0 0 P3 P2 P1 P0 - 02h P3 P2 Reset state 1/4duty (1/3bias) 0 0 1/3duty (1/3bias) 0 1 Static (1/1bias) 1 * *: Dont care In 1/3duty, Display data and Blink data of COM3 is ineffective. COM1 and COM3 output are same data. Please be careful of transmission of display data and blink data. The examples of SEG/COM output waveform, under the each Bias/Duty set up, are shown at "LCD Driver Bias/Duty Circuit" description. Frame Frequency Set Condition (1/4,1/3,1/1duty) (128Hz, 130Hz, 128Hz) (85Hz, 86hz, 64Hz) (64Hz, 65Hz, 48Hz) (51Hz, 52Hz, 32Hz) P1 P0 0 0 1 1 0 1 0 1 Reset state Relation table, between Frame frequencies (FR), integrated oscillator circuit (OSC) and Divide number. (Note1) Divide FR [Hz] DISCTL Duty set (P3,P2) Duty set (P3,P2) (P1,P0) (0,0) (0,1) (1,*) (0,0) (0,1) (1,*) (0,0) 1/4duty 160 1/3duty 156 1/1duty 160 1/4duty 128 1/3duty 131.3 1/1duty 128 (0,1) 240 237 320 85.3 86.4 64 (1,0) 320 315 428 64 65 47.9 (1,1) 400 393 640 51.2 52.1 32 (Note1) FR is frame frequency, in case OSC frequency = 20.48KHz (typ). The Formula, to calculate OSC frequency from Frame frequency is below. " OSC frequency = Frame frequency (measurement value) x Divide number " Divide numberPlease decide by using the value of Frame Frequency Set (P1,P0) and duty setting (P3,P2). Ex) (P1,P0) = (0,1) , (P3,P2) = (0,1) => www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Divide number= 237 22/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Address Set (ADSET) st 1 byte Command 2 nd byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 0 0 1 1 83h - 0 0 P5 P4 P3 P2 P1 P0 - 00h Set start address to write DDRAM data. The address can be set from 00h to 30h. (Address 31h is used at dummy address) Do not set other address. (Except 00h to 31h address is not acceptable.) In case, write data to DDRAM, please send RAMWR command certainly. Blink Set (BLKSET) st 1 byte Command 2 nd byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 0 1 0 0 84h - 0 0 0 0 0 P2 P1 P0 - 00h Set Blink ON/OFF. About detail, please refer to a "Blink function". Blink set Blink mode(Hz) P2 P1 P0 Reset state OFF 0 0/* 0/* 1.6 1 0 0 2.0 1 0 1 2.6 1 1 0 4.0 1 1 1 *: Dont care Blink Address Set (BLKADSET) st 1 byte Command 2 nd byte Command MSB D/C D6 1 0 0 0 0 1 0 0 P5 P4 P3 P2 D5 D4 D3 D2 LSB D0 Hex 1 1 87h - P1 P0 - 00h D1 Reset Set Blink data RAM start address to write. The address can be set from 00h to 30h. (Address 31h is used at dummy address) Do not set other address. (Except 00h-31h address is not acceptable.) In case, write data to Blink RAM, please send BLKWR command certainly. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 23/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) SEG/GPO Port Change (OUTSET1) MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 1 0 0 0 88h - 0 0 0 P4 P3 P2 P1 P0 - 00h st 1 byte Command 2 nd byte Command Set output mode, Segment output or GPO output. P4 to P0: Select changing port number. (SEG15 to SEG45 ports are SEG mode/GPO mode selectable) In case, GPO output is selected, Terminal output data is set by GPOSET command. Ex) In case SEG45 port assigned to GPO, If GPO1 data is "H", GPO1 (SEG45) port outputs "H" (VLCD Level). If GPO1 data is "L", GPO1 (SEG45) port outputs "L" (VSS level). Output terminal state under the P2 to P0 set condition is listed below (BU97981KV ,BU97981GU) Condition P4 P3 P2 P1 P0 SEG Terminal state (SEG output/GPO output) SEG15 SEG16 SEG17 SEG18 Terminal Terminal Terminal Terminal SEG42 SEG43 SEG44 SEG45 Terminal Terminal Terminal Terminal 0 0 0 0 0 SEG15 SEG16 SEG17 SEG18 SEG42 SEG43 SEG44 SEG45 0 0 0 0 1 SEG15 SEG16 SEG17 SEG18 SEG42 SEG43 SEG44 GPO1 0 0 0 1 0 SEG15 SEG16 SEG17 SEG18 SEG42 SEG43 GPO2 GPO1 0 0 0 1 1 SEG15 SEG16 SEG17 SEG18 SEG42 GPO3 GPO2 GPO1 0 0 0 0 SEG15 SEG16 SEG17 SEG18 GPO4 GPO3 GPO2 GPO1 1 1 SEG15 SEG16 SEG17 SEG18 GPO4 GPO3 GPO2 GPO1 SEG16 SEG17 GPO28 GPO4 GPO3 GPO2 GPO1 1 1 1 0 1 1 1 0 0 SEG15 1 1 1 0 1 SEG15 SEG16 GPO29 GPO28 GPO4 GPO3 GPO2 GPO1 1 1 1 1 0 SEG15 GPO30 GPO29 GPO28 GPO4 GPO3 GPO2 GPO1 1 1 1 1 1 GPO31 GPO30 GPO29 GPO28 GPO4 GPO3 GPO2 GPO1 (BU97981MUV) Condition SEG Terminal state (SEG output/GPO output) P4 P3 P2 P1 P0 SEG12 SEG13 SEG14 SEG15 Terminal Terminal Terminal Terminal SEG35 SEG36 SEG37 SEG38 Terminal Terminal Terminal Terminal 0 0 0 0 0 SEG12 SEG13 SEG14 SEG15 SEG35 SEG36 SEG37 SEG38 0 0 0 0 1 SEG12 SEG13 SEG14 SEG15 SEG35 SEG36 SEG37 GPO1 0 0 0 1 0 SEG12 SEG13 SEG14 SEG15 SEG35 SEG36 GPO2 GPO1 0 0 0 1 1 SEG12 SEG13 SEG14 SEG15 SEG35 GPO3 GPO2 GPO1 0 0 0 0 SEG12 SEG13 SEG14 SEG15 GPO4 GPO3 GPO2 GPO1 1 0 1 1 1 1 SEG12 SEG13 SEG14 SEG15 GPO4 GPO3 GPO2 GPO1 1 1 0 0 0 SEG12 SEG13 SEG14 GPO24 GPO4 GPO3 GPO2 GPO1 1 1 0 0 1 SEG12 SEG13 GPO25 GPO24 GPO4 GPO3 GPO2 GPO1 1 1 0 1 0 SEG12 GPO26 GPO25 GPO24 GPO4 GPO3 GPO2 GPO1 1 1 0 1 1 GPO27 GPO26 GPO25 GPO24 GPO4 GPO3 GPO2 GPO1 GPO27 GPO26 GPO25 GPO24 GPO4 GPO3 GPO2 GPO1 11100 - 11111 In case, the SEG port is switched to the GPO port, DDRAM address and Blink RAM address do not change. In this case, DDRAM address and Blink RAM address, selected GPO output mode, is dummy address. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 24/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Change Command of a SEG/LED port (OUTSET2) MSB D/C st 1 byte Command 2 nd byte Command D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 1 0 0 1 89h - 0 0 0 0 0 P2 P1 P0 - 00h This command affects segment port/LED port selection and PWM resolution set up. P2: Resolution setting Setting P2 Reset condition 12bit resolution mode 0 8bit resolution mode 1 P1 to P0: select SEG driving mode or LED driving mode, this command affect at SEG46 to SEG48 port. The effective address is 00h to 03h. In case LED driving mode is selected, output turns into "NMOS Open Drain" from segment output. The state of the output terminal in case P1 to P0 are setup is shown below (BU97981KV, BU97981GU) Setting SEG Terminal state (SEG output/LED output) P1 P0 SEG46 Terminal SEG47 Terminal SEG48 Terminal 0 0 SEG46 SEG47 SEG48 0 1 SEG46 SEG47 LED1 1 0 SEG46 LED2 LED1 1 1 LED3 LED2 LED1 (BU97981MUV) Setting SEG Terminal state (SEG output/LED output) P1 P0 SEG39 Terminal SEG40 Terminal SEG41 Terminal 0 0 SEG39 SEG40 SEG41 0 1 SEG39 SEG40 LED1 1 0 SEG39 LED2 LED1 1 1 LED3 LED2 LED1 In this case, DDRAM address and a Blink RAM address of SEG port that set up to LED port, do not change. The address assigned to LED port is used as dummy address respectively. The output state of GPO, LED, and PWMOUT port under the INHb H/L, display on/off, and RESET state are listed below. Control port GPO INHb H According to GPOSET command DISPLAY L Low Fix PWMOUT According to PWM2SET command Low Fix LED According to PWM1/PWM2SET command Hi-Z www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 ON According to GPOSET command OFF According to GPOSET command According to PWM2SET command According to PWM2SET command According to According to PWM1/PWM2SET PWM1/PWM2SET command command 25/46 RESET state GPO unselected (All SEG output) Low Fix LED unselected (All SEG output) TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) LED1 Drive-Control (PWM1 "H" width control) Command (PWM1SET) MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 1 0 1 0 8Ah - byte Command 0 0 P11 P10 P9 P8 P7 P6 3 byte Command 0 0 P5 P4 P3 P2 P1 P0 - 00h 00h st 1 byte Command 2 nd rd nd rd 2 and 3 byte command data are able to set from 00h to 3Fh (described as 8bit binary data). nd rd In case, other value selected, sending command is ignored, and 2 and 3 byte command data set 3Fh. nd rd In reset state, 2 and 3 byte command data set 00h. In case, the command less than 3 byte, sending command are canceled. According to PWM1SET command, LED1 driving signal is adjustable. PWM "H" width is adjustable by 12bit/8bit resolution. nd rd Explanation about P11 to P6 data of 2 byte command and P5 to P0 data of 3 byte command as follows nd rd (The 2 byte data are used as upper 6bit, and 3 byte data are used as lower 6 bits.) 12bit mode : P11 data is used as MSB of 12 bits, and P0 data is used as LSB. 8bit mode : P11 to P8 are used as invalid bit. P7 data is used as MSB of 8 bits, and P0 data is used LSB. LED driving period is decided by the "H" width of PWM signal, generated by PWM generator circuit. (resolution: 8bit/12bit selectable) Ex.1 In case of external PWM clock 2MHz, parameter setting value is 2047 (P11 to P0 data: 7FFh) 1bit resolution: 500ns ALL HI setting: PWM signal frequency about 500Hz, H width about 2.00msec ALL Low setting: PWM signal frequency about 500Hz, H width 0us (In case of 12bit) Ex.2 In case of internal PWM clock 40.96KHz(TYP), parameter 127 (P11 to P0 data: 7Fh) 1bit resolution: 24.41us ALL HI setting: PWM signal frequency about 160Hz, H width about 6.20msec ALL Low setting: PWM signal frequency about 160Hz, H width 0us (In case of 8bit) BU97981 series PWM frequency is twice faster than BU9798 series in case of internal OSC clock use. This command is reflected, synchronizing with a next PWM frame head. And, LED port output is as follows INHb="H" : LED port output LED driving signal. INHb="L" : LED port output Hi-Z. LED port operation does not affect Display ON/OFF state. FFFh(FFh) (H width : wide PMW(ALL HI Duty shift 000h(00h) (H width : narrrow PMW(ALL Low About the PWM frequency and PWM "H" width calculation PWM cycle and PWM "H" width, decided by PWM clock cycle is described as follows. (PWM clock cycle is a minimum unit of PWM "H" width) PWM frequency = PWM clock cycle x (Number of the steps(12bit = 4096, 8bit =256) - 1) PWM H width = PWM clock cycle x Parameter set value(12bit: 0 to 4095, 8bit: 0 to 255) PWM Duty = PWM H width/PWM cycle = Parameter set value / Number of the steps In case, PWM is generated from internal clock, the PWM cycle varies, according to OSC frequency. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 26/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) LED2 to 3 Drive-Control (PWM2 "H" width control) Command (PWM2SET) MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 0 1 0 1 1 8Bh - byte Command 0 0 P11 P10 P9 P8 P7 P6 - 00h 3 byte Command 0 0 P5 P4 P3 P2 P1 P0 - 00h st 1 byte Command 2 nd rd P7 to P0 data are able to set from 00h to 3Fh (described as 8bit binary data). In case, other value selected, sending command is ignored, and P7 to P0 data set 3Fh. In reset state, P7 to P0 data is 00h. In case, the command less than 3 byte, sending command are canceled. According to PWM2SET command, LED2 driving signal, LED3 driving signal, and PWMOUT output "H" width are adjustable. PWM "H" width is adjustable by 12bit/8bit resolution. nd rd Explanation about P11 to P6 data of 2 byte command and P5 to P0 data of 3 byte command as follows nd rd (The 2 byte data are used as upper 6bit, and 3 byte data are used as lower 6 bits.) 12bit mode : P11 data is used as MSB of 12 bits, and P0 data is used as LSB. 8bit mode : P11 to P8 are used as invalid bit. P7 data is used as MSB of 8 bits, and P0 data is used LSB. LED driving period is decided by the "H" width of PWM signal, generated by PWM generator circuit. (resolution : 8bit/12bit selectable) Ex.1 In case of external PWM clock 2MHz, parameter setting value is 2047 (P11 to P0 data: 7FFh) 1bit resolution: 500ns ALL HI setting: PWM signal frequency about 500Hz, H width about 2.00msec ALL Low setting: PWM signal frequency about 500Hz, H width 0us (In case of 12bit) Ex.2 In case of internal PWM clock 40.96KHz(TYP), parameter 127 (P11 to P0 data: 7Fh) 1bit resolution: 24.41us ALL HI setting: PWM signal frequency about 160Hz, H width about 6.20msec ALL Low setting: PWM signal frequency about 160Hz, H width 0us (In case of 8bit) BU97981 PWM frequency is twice faster than BU9798 in case of internal OSC clock use. This command is reflected, synchronizing with a next PWM frame head. And, LED port output is as follows INHb="H" : LED port output LED driving signal, PWMOUT port output PWM signal. INHb="L" : LED port output Hi-Z, PWMOUT port output "L" LED port and PWMOUT port operation do not affect Display ON/OFF state. FFFh(FFh) (H width : wide PMW(ALL HI Duty shift 000h(00h) (H width : narrrow PMW(ALL Low About the PWM frequency and PWM "H" width calculation PWM cycle and PWM "H" width, decided by PWM clock cycle is described as follows. (PWM clock cycle is a minimum unit of PWM "H" width) PWM frequency = PWM clock cycle x (Number of the steps (12bit = 4096, 8bit =256) - 1) PWM H width = PWM clock cycle x Parameter set value (12bit: 0 to 4095, 8bit: 0 to 255) PWM Duty = PWM H width/PWM cycle = Parameter set value / Number of the steps In case, PWM is generated from internal clock, the PWM cycle varies, according to OSC frequency. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 27/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) RAM WRITE (RAMWR) st 1 byte Command 2 nd MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 1 0 0 0 0 0 A0h - byte Command Display data Random .... N byte Command Display data Random st Input data, sending after 1 byte command, are used as Display data. And display data are sent every 4bits. Please set this command after the ADSET command. Blink RAM WRITE (BLKWR) st 1 byte Command 2 nd MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 1 0 0 0 0 0 0 C0h - byte Command Blink data Random .... N byte Command Blink data Random st Input data, sending after 1 byte command, are used as Display data. And display data are sent every 4bits. Please set this command after the BLKADSET command. All Pixel ON (APON) st 1 byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 1 0 0 0 1 91h - After sending the command, all SEG output set display on state regardless of the DDRAM data. (This command affect to the SEG output terminal only (except GPO and LED output) ) All Pixel OFF (APOFF) st 1 byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 1 0 0 0 0 90h - After sending the command, all SEG output set display off state regardless of the DDRAM data. (This command affect to the SEG output terminal only (except GPO and LED output) ) All Pixel ON/OFF mode off (NORON) st 1 byte Command MSB D/C D6 D5 D4 D3 D2 1 0 0 1 0 0 D1 LSB D0 Hex Reset 1 1 93h - Hex Reset 92h - After sending the command, all SEG output released from APON/APOFF state. And SEG port output signal according to DDRAM data. (This command affect to the SEG output terminal only (except GPO and LED output) ) After reset sequence or SWRST, all output set NORON state. Software Reset (SWRST) st 1 byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 1 0 0 1 0 0 1 0 After sending the command, device set the reset state. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 28/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) OSC External Input Command (OSCSET) st 1 byte Command 2 nd byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 1 1 0 0 0 98h - 0 0 0 0 0 P2 P1 P0 - 00h According to the command, 4type of clock mode selectable include external clock input mode. Detail of this command function as follows. P2 P1 P0 Reset state Internal CLK (PWM generation OFF) Condition 0 0 0 External CLK input for PWM (PWM generation OFF) 0 0 1 Internal CLK (PWM generation ON) 0 1 0 External CLK input for PWM (PWM generation ON) 0 1 1 External CLK input for Display 1 * * (ROHM use only) *: Dont care (P2,P1,P0)=(0,0,1) : External PWM input mode CLKINexternal PWM input available. PWMOUT: "L" Output *under the (P2,P1,P0)=(0,0,0) condition PWMOUT into same state (P2,P1,P0)=(0,1,0) : PWM is made from integrated oscillation frequency PWM width is set up by PWM1SET and PWM2SET command. PWM waveform output from PWMOUT is set up by PWM2SET command. (P2,P1,P0)=(0,1,1) : PWM is made from External CLK input from CLKIN PWM width is set up by PWM1SET and PWM2SET command. PWM waveform output from PWMOUT is set up by PWM2SET command. The relation of OSC function control by each command is as follows SEG output integrated OSC CLKIN terminal LED1 (KV: SEG48) (MUV: SEG41) (GU: G4SEG48) PWM generation External CLK (PWM1SET) External PWM SEG output PWM generation PWMOUT terminal PWMOUT LED2,3 (KV: SEG47,46) (MUV: SEG40,39) (GU: SEG47,46) (PWM2SET) Output Control Circuit PWM resolution OSCSET command PWMSET command OUTSET command Figure 18. OSC External Input www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 29/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Integrated Regulator Setting (REGSET) st 1 byte Command 2 nd byte Command MSB D/C D6 D5 D4 D3 D2 D1 LSB D0 Hex Reset 1 0 0 1 1 0 0 1 99h - 0 0 0 0 0 P2 P1 P0 - 00h Set integrated regulator output voltage (Vreg). Integrated regulator is turned ON/OFF according to DISPON/OFF state that controlled by MODESET command. Setting P2 P1 P0 Reset state OFF (VLCD voltage) 0 0 0 5.0V 0 0 1 4.6V 0 1 0 4.5V 0 1 1 4.4V 1 0 0 3.4V 1 0 1 3.3V 1 1 0 3.2V 1 1 1 Please satisfy condition that REG voltage VLCD-0.5V. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 30/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) GPO Output Set Command (GPOSET) MSB D/C D6 D5 D4 D3 D2 D1 1 0 0 1 1 0 1 st 1 byte Command 2 nd LSB D0 0 Hex Reset 9Ah - byte Command GPO output data: P7 to P0 - 00h rd 3 byte Command GPO output data: P15 to P8 - 00h th GPO output data: P23 to 16 - 00h - 00h 4 byte Command th 5 byte Command * GPO output data: P30 to 24 *: Dont care Set GPO output data. The relation between SEG port (GPO port) and data is below. (BU97981KV, BU97981GU) GPOSET GPO SEG GPOSET GPO data port port data port P0 GPO1 SEG45 P10 GPO11 SEG port SEG35 GPOSET data P20 GPO port GPO21 SEG port SEG25 P1 GPO2 SEG44 P11 GPO12 SEG34 P21 GPO22 SEG24 P2 GPO3 SEG43 P12 GPO13 SEG33 P22 GPO23 SEG23 P3 GPO4 SEG42 P13 GPO14 SEG32 P23 GPO24 SEG22 P4 GPO5 SEG41 P14 GPO15 SEG31 P24 GPO25 SEG21 P5 GPO6 SEG40 P15 GPO16 SEG30 P25 GPO26 SEG20 P6 GPO7 SEG39 P16 GPO17 SEG29 P26 GPO27 SEG19 P7 GPO8 SEG38 P17 GPO18 SEG28 P27 GPO28 SEG18 P8 GPO9 SEG37 P18 GPO19 SEG27 P28 GPO29 SEG17 P9 GPO10 SEG36 P19 GPO20 SEG26 P29 GPO30 SEG16 P30 GPO31 SEG15 (BU97981MUV) GPOSET GPO data port P0 GPO1 SEG port SEG38 GPOSET data P10 GPO port GPO11 SEG port SEG28 GPOSET data P20 GPO port GPO21 SEG port SEG18 P1 GPO2 SEG37 P11 GPO12 SEG27 P21 GPO22 SEG17 P2 GPO3 SEG36 P12 GPO13 SEG26 P22 GPO23 SEG16 P3 GPO4 SEG35 P13 GPO14 SEG25 P23 GPO24 SEG15 P4 GPO5 SEG34 P14 GPO15 SEG24 P24 GPO25 SEG14 P5 GPO6 SEG33 P15 GPO16 SEG23 P25 GPO26 SEG13 P6 GPO7 SEG32 P16 GPO17 SEG22 P26 GPO27 SEG12 P7 GPO8 SEG31 P17 GPO18 SEG21 P27 - - P8 GPO9 SEG30 P18 GPO19 SEG20 P28 - - P9 GPO10 SEG29 P19 GPO20 SEG19 P29 - - P30 - - GPO data is transmitted for every 1byte, and GPO data output is asynchronous from frame cycle. In case INHb="H", GPO output signal according to GPOSET data, on the other hand, in case INHb="L" GPO output GND level. GPO output does not influence by Display ON/OFF state. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 31/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) LCD Driving Waveform 1/4Duty Line inversion Frame inversion SEGn SEGn+1 SEGn+2SEGn+3 SEGn SEGn+1 SEGn+2SEGn+3 COM0 stateA COM0 stateA COM1 stateB COM1 stateB COM2 COM2 COM3 COM3 1frame 1frame Vreg Vreg COM0 COM0 VSS VSS Vreg COM1 Vreg COM1 VSS VSS Vreg COM2 Vreg COM2 VSS VSS Vreg COM3 Vreg COM3 VSS VSS Vreg SEGn Vreg SEGn VSS VSS Vreg SEGn+1 Vreg SEGn+1 VSS VSS Vreg SEGn+2 Vreg SEGn+2 VSS VSS Vreg Vreg SEGn+3 SEGn+3 VSS VSS Vreg Vreg stateA stateA (COM0-SEGn) (COM0-SEGn) -Vreg -Vreg Vreg Vreg stateB stateB (COM1-SEGn) (COM1-SEGn) -Vreg -Vreg Figure 19. Waveform of Line Inversion www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Figure 20. Waveform of Frame Inversion 32/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) 1/3Duty Line inversion Frame inversion SEGn SEGn+1 SEGn+2SEGn+3 SEGn SEGn+1 SEGn+2SEGn+3 COM0 stateA COM0 stateA COM1 stateB COM1 stateB COM2 COM3 COM2 COM3 When 1/3duty COM3 and COM1 is same 1frame When 1/3duty COM3 and COM1 is same 1frame Vreg Vreg COM0 COM0 VSS VSS Vreg Vreg COM1 COM1 VSS VSS Vreg Vreg COM2 COM2 VSS VSS Vreg Vreg When 1/3duty COM3 and COM1 COM3 is same COM3 VSS VSS Vreg Vreg SEGn SEGn VSS VSS Vreg Vreg SEGn+1 SEGn+1 VSS VSS Vreg Vreg SEGn+2 SEGn+2 VSS VSS Vreg Vreg SEGn+3 SEGn+3 VSS VSS Vreg Vreg stateA stateA (COM0-SEGn) (COM0-SEGn) -Vreg -Vreg Vreg Vreg stateB stateB (COM1-SEGn) (COM1-SEGn) -Vreg -Vreg Figure 21. Waveform of Line Inversion www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Figure 22. Waveform of Frame Inversion 33/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) 1/1Duty (Static) Line inversion Frame inversion SEGn SEGn+1 SEGn+2SEGn+3 COM0 COM1 SEGn SEGn+1 SEGn+2SEGn+3 stateA stateB COM2 When 1/1duty (Static) COM1 / COM0 is same waveform COM3 COM2 / COM0 is same waveform COM0 COM1 COM2 COM3 1frame stateA stateB When 1/1duty (Static) COM1 / COM0 is same waveform COM2 / COM0 is same waveform 1frame Vreg Vreg COM0 COM0 VSS Vreg COM1 COM1 / COM0 is same waveform VSS VSS When 1/1duty (Static) Vreg COM1 VSS Vreg Vreg COM2 / COM0 is same waveform COM2 COM2 VSS VSS Vreg Vreg COM3 / COM0 is same waveform COM3 VSS COM3 VSS Vreg Vreg SEGn SEGn VSS VSS Vreg Vreg SEGn+1 SEGn+1 VSS VSS Vreg Vreg SEGn+2 SEGn+2 VSS VSS Vreg Vreg SEGn+3 SEGn+3 VSS VSS Vreg Vreg stateA stateA -Vreg -Vreg Vreg Vreg stateB stateB -Vreg -Vreg Figure 23. Waveform of Line Inversion www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Figure 24. Waveform of Frame Inversion 34/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet Initialize Sequence Please input sequence listed below, before start LCD driving. (Refer to Power ON/OFF sequence) INHb=L Input voltage supply CSB H ...interface initializing CSB L ...interface command sending SWRST ...software reset MODESET ...Display off Various commands setting RAM WRITE Blink RAM WRITE MODESET ...Display on INHb = H Start LCD driving Before initialize sequence, DDRAM address, DDRAM data, Blink address and Blink data are random condition. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Cautions of Power-On/ Power-Off condition POR circuit This LSI has "P.O.R" (Power-On Reset) circuit and Software Reset function. Please keep the following recommended Power-On conditions in order to power up properly. 1. Please set power up conditions to meet the recommended tR, tF, tOFF, and Vbot spec below in order to ensure P.O.R operation. (The detection voltage of POR varies because of environment etc. To operate POR surely, Please satisfy Vbot lower than 0.5V condition.) VDD Recommendation condition of tR, tF, tOFF, Vbot tR VDET tOFF tR tOFF Vbot VDET less than 10ms Over 1ms less than 0.5V TYP 1.2V Vbot * VDET : POR detect level Fig 18: Power ON/OFF wave form Figure 25. Power ON/OFF Wave 2. If it is difficult to meet above conditions, execute the following sequence after Power-On. (1) CSB="L""H" condition (2) After CSB"H""L", execute SWRST command. In addition, in order to the SWRST command certainly, please wait 1ms after a VDD level reaches to 90% and CSB="L""H". Before SWRST command input device will be in unstable state, since SWRST command does not operate perfect substitution of a POR function. VDD CSB Min 1ms Min 50ns SWRST Command Figure 26. SWRST Command Sequence www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 36/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Power ON/OFF Sequence Display ON/OFF control by INHb terminal is not asynchronous frame cycle. To prevent incorrect display, malfunction and abnormal current, VDD must be turned on before VLCD in power up sequence. VDD must be turned off after VLCD in power down sequence. Please set INHb terminal ="L" during Power ON/OFF sequence. Please satisfies VLCD Please satisfies VLCDVDD, t1>0ns, t2>0ns t2 t1 VLCD 10% VDD VDD min 10% VDD min INH SWRST Command MODE SET Display off Various Setup RAM WRITE Blink RAM WRITE MODE SET Display on MODE SET Display o Figure 27. Power On/Off Sequence Integrated Regulator Start-up Sequence BU97981KV/MUV do not support integrated regulator start-up, during the normal (Vreg unused) display operation. So, in case, LCD power supply change to Vreg output under the normal operation period, display flickering will occur. In order to prevent this phenomenon please send MODESET command (Disp on) after REGSET command. Please satisfies VLCD Please satisfies VLCDVDD, t1>0ns, t2>0ns After SWRST command sending, please send same sequence. t2 t1 VDD 10% 10% VLCD VDD min VDD min INH SWRST Command MODE SET Display off Various Setup REGSET RAM WRITE Blink RAM WRITE MODE SET Display on MODE SET Display o Figure 28. Integrated Regulator Start-up Sequence LED Power Supply On/Off Sequence In order to prevent irregular current, please start LED power supply after VLCD input and OUTSET2 command sending. Please satisfies VLCD Please satisfies VLCDVDD, t1>0ns, t2>0ns VLED t2 t1 VLCD VDD 10% 10% VDD min VDD min INH Command SWRST MODE SET Display off Various Setup OUTSET2 RAM WRITE Blink RAM WRITE MODE SET Display on MODE SET Display o Figure 29. LED Power Supply On/Off Sequence www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 37/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Attention About Input Port Pull Down Satisfy the following sequence if input terminals are pulled down by external resisters (In case MPU output Hi-Z). Date transaction period with MPU Input "L" period Input"Hi-Z" period CSB SD SCL Figure 30. Recommended Sequence When Input Ports are Pulled Down BU97981KV / BU9798MUV /BU97981GU adopts a 5V tolerant I/O for the digital input. This circuit includes a bus-hold function to keep the level of HIGH. A pull down resistor of below 10Kshall be connected to the input terminals to transit from HIGH to LOW because the bus-hold transistor turns on during the inputs HIGH level. (Refer to the Figure 7, Figure 8; I/O Equivalent Circuit) A higher resistor than approximate 10Kcauses input terminals being steady by intermediate potential between HIGH and LOW level so unexpected current is consumed by the system. The potential depends on the pull down resistance and bus-hold transistors resistance. As the bus-hold transistor turns off upon the input level cleared to LOW a higher resistor can be used as a pull down resistor if a MPU set SD and SCL lines to LOW before it releases the lines. The LOW period preceding MPUs bus release shall be at least 50ns as same as a minimum CLK width ( tSLW ). www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 38/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Operational Notes 1. Reverse Connection of Power Supply Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the ICs power supply pins. 2. Power Supply Lines Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. Ground Voltage Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. Ground Wiring Pattern When using both small-signal and large-current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of external components do not cause variations on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance. 5. Thermal Consideration Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the Pd rating. 6. Recommended Operating Conditions These conditions represent a range within which the expected characteristics of the IC can be approximately obtained. The electrical characteristics are guaranteed under the conditions of each parameter. 7. Inrush Current When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. Operation Under Strong Electromagnetic Field Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction. 9. Testing on Application Boards When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The ICs power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and storage. 10. Inter-pin Short and Mounting Errors Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 39/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet Operational Notes - continued 11. Unused Input Pins Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. Regarding the Input Pin of the IC In the construction of this IC, P-N junctions are inevitably formed creating parasitic diodes or transistors. The operation of these parasitic elements can result in mutual interference among circuits, operational faults, or physical damage. Therefore, conditions which cause these parasitic elements to operate, such as applying a voltage to an input pin lower than the ground voltage should be avoided. Furthermore, do not apply a voltage to the input pins when no power supply voltage is applied to the IC. Even if the power supply voltage is applied, make sure that the input pins have voltages within the values specified in the electrical characteristics of this IC. 13. Data transmission To refrain from data transmission is strongly recommended while power supply is rising up or falling down to prevent from the occurrence of disturbances on transmission and reception. www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 40/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Ordering Information B U 9 7 9 8 1 Part Number x U x - Package KV MUV GU B x 9 7 9 Part Number 8 1 : VQFP64 : VQFN56AV8080 : VBGA64T050A G U - Package GU :VBGA64T050A E2 Packaging and forming specification E2: Embossed tape and reel (VQFP64, VQFN56AV8080) ZE 2 Packaging and forming specification E2: Embossed tape and reel (VBGA64T050A) Lineup Package Orderable Part Number VQFP64 Reel of 1000 BU97981KV-E2 VQFN56AV8080 Reel of 1000 BU97981MUV-E2 VBGA64T050A Reel of 2500 BU97981GU-ZE2 www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 41/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Datasheet Physical Dimension, Tape and Reel Information Package Name VQFP64 UNITmm PKGVQFP64 Drawing: EX252-5001-1 www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 42/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Package Name www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Datasheet VQFN56AV8080 43/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series MAX 196 segments (SEG49xCOM4) Package Name Datasheet VBGA064T050A <> () 1234 1234 www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1234 1234 44/46 1234 1234 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Marking Diagrams VQFN56AV8080 (TOP VIEW) VQFP64 (TOP VIEW) Part Number Marking BU97981KV Part Number Marking BU97981 LOT Number 1PIN MARK 1PIN MARK VBGA64T050A (TOP VIEW) LOT Number 1PIN MARK Part Number Marking BU97981 LOT Number Part Number Package Part Number Marking BU97981KV VQFP64 BU97981KV BU97981MUV VQFN56AV8080 BU97981 BU97981GU VBGA64T050A BU97981 www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 45/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 BU97981xxx Series Datasheet MAX 196 segments (SEG49xCOM4) Revision History Date Revision 31.Aug.2012 10.Oct.2012 001 002 21.Aug.2013 003 17.Dec.2014 004 4.Feb.2015 10.Apr.2015 005 006 Changes New Release P.7 (BU97981MUV) Output voltage1 MIN: 4.35 -> 4.25, MAX:4.65 -> 4.70 Output voltage2 MIN:4.42 -> 4.38, MAX:4.58 -> 4.62 P.10, P.11 Example of recommended circuit seg -> segments Change to New Style P.7 (BU97981MUV) Output voltage1 MIN: 4.25 -> 4.30 Add GU Package P.1 Delete Package figure P.41 Add "Z" character in Ordering information P.37 Add the condition when power supply P.37 Modified and add the Figure of Power ON/OFF Sequence www.rohm.com (c) 2012 ROHM Co., Ltd. All rights reserved. TSZ2211115001 46/46 TSZ02201-0A2A0D300110-1-2 10.Apr.2015 Rev.006 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bu97981muv - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bu97981muv VQFN56AV8080 1000 1000 Taping inquiry Yes