G34960003700 - Carlo Gavazzi Group

Du line

Fieldbus Installationbus

Specifications are subject to change without notice (05.05.03) 1

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Type: Dupline®

H4-Housing

Combined module

Interface type

DC supply

•

Interface for Mitsubishi PLC with the function of a master

•Plug and play: Automatic communication with specific

PLC/Controllers

•Built-in normal Dupline®Channel Generator

•128 I/O’s and DC power supply on 3 wires

•RS232/RS422/RS485 port for interfacing to control

system

•Split-I/O mode selectable (128 inputs and 128 outputs)

•LED-indications for supply, Dupline®carrier and Com-

port TX

•Galvanically isolated Com-port supplied by internal

DC/DC converter

Product Description Ordering Key

G 3496 0003 is designed as a

cost-effective solution for

interfacing Dupline®I/O’s to a

Mitsubishi PLC. It performs

three functions: Dupline®

channel generator, power

supply synchronization (en-

ables 3-wire system with

supply) and RS232/RS422/

RS485 interface.

Type Selection

Supply PLC Interface Conformance Ordering no.

20-30 VDC Mitsubishi FX-serie G 3496 0003 700

Mitsubishi AnS-serie

with interface module

G 3496 0003 700

Input/Output Specifications

Dupline®Plug & Play Master Module

Interface for Mitsubishi PLC

Power output

Output voltage 20-30 VDC (pulsating)

Output current < 3.0 A @ 50ºC

Short circuit protection 4 A quick acting fuse

Output voltage drop < 1.0 V

Dupline®carrier

Output voltage 8.2 V (pulsating)

Current < 60 mA

Short circuit protection Yes

Scan time

128 channels 132.2 ms

64 channels 69.8 ms

Communication port

Standard RS232/RS422/RS485

Split I/O mode Yes, selectable

Normal Dupline mode Yes, selectable

Connection 9 pole female Sub-D

Dielectric voltage

Com-port Dupline®1 kVAC (rms)

Protocol Programming Port

Baud rate 9600

Data bits 7

Start bit 1

Stop bit 1

Parity Even

Flow-control None

Protocol Dedicated Protocol

Baud rate 19200

Data bits 8

Start bit 1

Stop bit 1

Parity None

Flow-control None

Type G 3496 0003

Input/Output Specifications (Cont.)

Pin assignment

2-wire RS 485

S/R Data line + (B) Pin 3

S/R Data line - (A) Pin 8

GND Pin 5

4-wire RS 485/RS 422

R Data line + (B) Pin 3

R Data line - (A) Pin 8

S Data line + (B) Pin 2

S Data line - (A) Pin 7

Direction Pin 4

(Connect to GND pin 5

when using 4-wire commu-

nication)

RS 232

TX Pin 1

RX Pin 9

GND Pin 5

Supply Specifications

Power supply

Overvoltage cat. III (IEC 60664)

Operational voltage (Vin)20-30 VDC

Reverse polarity protection None

Current consumption < 150 mA + Power load

Power dissipation < 5 W

Transient protection voltage 800 V

Dielectric voltage

Supply - Dupline®None

Supply - com-port 1 kVAC (rms)

Power ON delay 2 s

Indication for

Com-port Tx LED, red

Supply ON LED, green

Dupline®carrier LED, yellow

Environment

Pollution degree 3 (IEC 60664)

Operating temperature 0° to +50°C (+32° to +122°F)

Storage temperature

-50° to +85°C (-58° to +185°F)

Du line

Fieldbus Installationbus

2Specifications are subject to change without notice (04.04.01)

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Mode of Operation

The Dupline

Master Module

(DMM) controls a 3-wire bus

with signal, DC-power and

common GND. The DMM is

connected to a standard DC-

supply, which it synchronizes

with the Dupline

carrier signal

before it is output to supply.

The synchronization is neces-

sary in order to enable the

Dupline

and DC-supply to

share the GND-wire.

The Dupline

Master Module is

a Dupline

Channel Generator

with the function of a master.

This means that the 128

Dupline

I/O’s will be read/writ-

ten by the DMM and then sent

to the PLC.

The DMM can run in two dif-

ferent modes – Normal mode

and split I/O mode. In Normal

mode, Dupline

operates as a

peer-to-peer system, where

the channel generator auto-

matically establishes a con-

nection between Dupline

inputs and Dupline

outputs

which are coded to the same

Dupline

address. If e.g. an

input coded for B5 is activat-

ed, the output(s) coded for B5

will also be activated.

Consequently, a Dupline

-out-

put can either be activated

through the output-data

received on DMM or by an

active Dupline

input coded

for the same Dupline

address. In “Split I/O” mode,

the channel generator treats

the Dupline

inputs and

Dupline

outputs indepen-

dently. If e.g. an input coded

for B5 is activated, the DMM

will make the information avail-

able for the PLC (like in normal

mode), but it will not automati-

cally activate the Dupline out-

put(s) coded to B5. The

Dupline

outputs are con-

trolled exclusively through the

output data received from the

PLC. In this mode, up to 128

Dupline

inputs and 128

Dupline

outputs are available,

since an input and an output

coded to the same Dupline

address can operate indepen-

dently.

G 3496 0003

General Specifications

Humidity (non-condensing) 20 to 80%

Mechanical resistance

Shock 15 G (11 ms)

Vibration 2 G (6 to 55 Hz)

Dimensions H4-Housing

Material (see Technical information)

Weight 100 g

Dip-Switch Setting

Sw.2 On: If Communication fails, all Dupline

chan-

nels activated by the PLC, is deactivated.

Off: If Communication fails, Dupline

channels

activated by the PLC, remains activated.

Sw.3 On: Programming-port Protocol (Power up the

Module)

Off: Dedicated Protocol 1 (Power up the

Module)

Sw.4 On: Split I/O Channel Generator Mode

(See “Mode of Operation”)

Off: Normal Dupline

Monostable Channel

Generator Mode

Sw.5 On: 64 Dupline

channels

Off: 128 Dupline

channels

Memory Mapping

Dupline®Mitsubishi Dupline®Mitsubishi

Channel Channel

Read Write Read Write

A1 M0000 M0128 E1 M0032 M0160

A2 M0001 M0129 F1 M0040 M0168

A3 M0002 M0130 G1 M0048 M0176

A4 M0003 M0131 H1 M0056 M0184

A5 M0004 M0132 I1 M0064 M0192

A6 M0005 M0133 J1 M0072 M0200

A7 M0006 M0134 K1 M0080 M0208

A8 M0007 M0135 L1 M0088 M0216

B1 M0008 M0136 M1 M0096 M0224

B8 M0015 M0143 N1 M0104 M0232

C1 M0016 M0144 O1 M0112 M0240

D1 M0024 M0152 P1 M0120 M0248

Table of the memory mapping to the PLC

Wiring Diagram

1234

21 22 27 28

Supply in

20-30 V DC

678

Power out

GND

Dupline Signal

RS 232

RS 485

Du line

Fieldbus Installationbus

Specifications are subject to change without notice (04.04.01) 3

Dupline®is a registered trademark. A product of the CARLO GAVAZZI Group

Installation Hints

No Dupline

Carrier-LED

Short circuit Short circuit between the

two Dupline

wires.

Accessories

FX-Serie

Cable Sub-D 9M/25M for 25p

Programming port RS-422-MI2

Cable Sub-D 9M/8M DIN for 8p

Programming port RS-422-MI3

Through RS-485 Communication Adapter or PCB

Cable Sub-D 9M/6Wires for com.

Module with Screw term. RS-422-MI1

Additional Information

Scope of supply

1 x Master Module G3496 0003 700

Pin Assignment

3SDA

RDA

SDB

RDB

+ 5 V

Com. module

with terminals

in (G 2196 0003 only)

G 2196 0003

G 3496 0003

RS-422-MI1

RS-422-MI3RS-422-MI2

G 3496 0003

Interface Modules

AnS-Series

RS232 Type A1SJ71UC24-R2*

RS422/485 Type A1SJ71UC24-R4*

FX-Serie

Directly through the programming port or

communicationmodul FXON-485ADP* or

Interface adapter FX2N-485BD*

* Mitsubishi product.

Dimensions (mm)

H4-housing