Ceramic Trimmer Capacitors
T13E.pdf
Sep.1,2017
EU RoHS Compliant
F**2&#.0-"3!21',2&'1!2*-%!-+.*7
5'2&-@
F-'12&#30-.#,'0#!2'4#
|z{{GG-,2&##120'!2'-,-$2&#
1#-$#02',80"-313 12,!#1',
*#!20'!*,"*#!20-,'!/3'.+#,2@
FFor+-0#"#2'*1A.*#1#0#$#r2o-ur5#
.%#A3021..0-!&$-0-
H&22.BGG555@+302@!-+G#,-
#3G13..-02G!-+.*',!#G0-&1J@
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Contents
Please check the MURATA website (http://www.murata.com/)
if you cannot find a part number in this catalog.
Product specifications are as of September 2017.
Part Numbering p2
Selection Guide of Ceramic Trimmer Capacitors
p3
Packaging p26
Recommended Adjustment Tools p28
Qualified Standards p29
TZR1 Series p4
TZY2 Series p8
TZC3 Series p13
1
2
3
TZW4 Series p18
4
TZB4 Series p21
5
Bluetoothr is a registered trademark
or trademark of Bluetooth SIG, Inc.
in the United States and other countries.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
o Part Numbering
(Part Number)
1Product ID
TZ Trimmer Capacitors
Product ID
4Maximum Capacitance
Expressed by three-digit alphanumerics. The unit is pico-farad
(pF). The first and second figures are significant digits, and the
third figure expresses the number of zeros that follow the two
numbers. If there is a decimal point, it is expressed by the capital
letter "R". In this case, all figures are significant digits.
Ceramic Trimmer Capacitors
5Terminal Shape
Code Terminal Shape
A
B
Top Adjustment:
Top Adjustment:
TZR1, TZY2, TZC3, TZW4, TZB4
TZB4
7Packaging
Code
B00
R00
R01*
Bulk
Reel (Taping ø180mm)
Reel (Taping ø330mm)
Packaging
2Series/Terminal
Code
B4
W4
C3
Y2
R1
4mm Size SMD Type
4mm Size SMD Type
3mm Size SMD Type
2mm Size SMD Type
1mm Size SMD Type
Series/Terminal
3Temperature Characteristics
Code
Z
R
K
P
NP0ppm/°C
N750ppm/°C
N1000ppm/°C
N1200ppm/°C
Temperature Characteristics
Please refer to dimensions for terminal details.
* TZB4 only.
6Individual Specifications
Code
001
C01
A01
A10
B10
TZR1, TZW4 Standard Type
TZY2 Standard Type
TZC3 Standard Type
TZB4 No-cover Film Standard Type
TZB4 with Cover Film Standard Type
Individual Specifications
Please refer to ratings for tolerance of temperature characteristics.
5
A
6
C01
1
TZ
7
R00
4
200
3
R
2
Y2
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2
Selection Guide
Height 3.2mm max.
Height 2.6mm max.
Surface Mount
Reflow Flow
High Frequency
Power
Mounting Method?
1.5(W) x 1.7(L)
TZR1 4.0(W) x 4.5(L)
(with cover film)
TZB4_AB
4.0(W) x 4.5(L)
(with cover film)
TZB4_BB
2.5(W) x 3.2(L)
TZY2
Height 0.90mm max.
Height 1.25mm max.
4.2(W) x 5.2(L)
TZW4
3.2(W) x 4.5(L)
TZC3
4.0(W) x 4.5(L)
TZB4_AA
Height 1.7mm max.
Height 3.2mm max.
4.0(W) x 4.5(L)
TZB4_BA
All Ceramic Trimmer Capacitor products comply with RoHS and ELV.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
3
(
Tolerance: ±0.1
in mm
)
1.7
1.5
0.9 max. 0.45
0.35
0.2 (Depth;0.15)
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZR1Z010A001 0.55 1.0 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZR1Z1R5A001 0.7 1.5 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZR1Z040A001 1.5 4.0 +100/-0% NP0±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZR1R080A001 3.0 8.0 +100/-0% N750±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
Insulation Resistance: 10000M ohm Torque: 0.1 to 1.0mNm Operating Temperature Range: -25 to +85°C
Cover
Metal Rotor
Monolithic Stator
Construction
Ceramic Trimmer Capacitors
TZR1 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
4
1
Features
1. Ultra-small and thin with external dimensions
of 1.5(W)x1.7(L)x0.85(H)mm
(80% less in volume than the current product).
2. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after reflow soldering.
3. Suitable for high frequency circuit due to high
self-resonant frequency (6.2GHz of TZR1Z010 at
1.0pF setting).
Applications
1. Bluetoothr
2. Crystal oscillators
3. Crystal filters
4. Miniature tuner packs (FM Radio, TV)
5. Remote keyless entry systems
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z010 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
Temperature Characteristics
TZR1Z010
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z1R5 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZR1Z1R5
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
Z040 (NP0±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZR1Z040
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R080 (N750±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZR1R080
10000
1000
100
10
1
00246
Frequency (GHz)
0.55pF set
1.0pF set
Z010
Q
810
Frequency Characteristics
TZR1Z010
10000
1000
100
10
1
00246
Frequency (GHz)
0.7pF set
1.5pF set
Z1R5
Q
810
TZR1Z1R5
1000 1000
100
10
Q
1
10
100
500 1000 1500 2000 2500
Frequency (MHz)
Capacitance (pF)
Z040
TZR1Z040
1000 1000
100
10
Q
1
10
100
500 1000 1500 2000
Frequency (MHz)
Capacitance (pF)
R080
TZR1R080
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
5
1
(
Tolerance: ±0.1
in mm
)
2.2
1.2
0.5
Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
oReflow Soldering Profile
n
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to n
1 )
oSoldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
Temperature Profile
Notice (Storage and Operating Conditions)
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
6
1
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Notice (Soldering and Mounting)
Notice (Handling)
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
7
1
1. Soldering
(1) TZR1 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(1.6mm external diameter and 0.8mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
*Recommended screwdriver for manual adjustment
MURATA: KMDR160
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 0.5 N [Ref: 50gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
(
Tolerance: ±0.1
in mm
)
3.2±0.2
1.0
2.5±0.2
0.95
1.25 max.
1.4
0.5
0.45
Insulation Resistance: 10000M ohm Torque: 0.7 to 4.9mNm Operating Temperature Range: -25 to +85°C
Cover
Metal Rotor
Monolithic Stator
Construction
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZY2Z010AC01 0.6 1.0 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZY2Z2R5AC01 1.0 2.5 +100/-0% NP0±300ppm/°C 200min. at 200MHz, Cmax. 25Vdc 55Vdc
TZY2Z030AC01 1.5 3.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2Z060AC01 2.5 6.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2Z100AC01 3.0 10.0 +100/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2R200AC01 4.5 20.0 +100/-0% N750±500ppm/°C 500min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2R250AC01 5.5 25.0 +100/-0% N750±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
TZY2K450AC01 8.0 45.0 +100/-0% N1000±500ppm/°C 300min. at 1MHz, Cmax. 25Vdc 55Vdc
Ceramic Trimmer Capacitors
TZY2 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
8
2
Features
1. Small and thin size with external dimensions
of 2.5(W)x3.2(L)x1.25max.(H)mm.
2. New shape of cover can improve the flux invasion
compared with current products.
3. Improvement of the adhesion between rotor and
stator leads to superior stability.
4. Unique construction with no plastic material
provides superior soldering heat resistance to
maintain excellent characteristic performance
after reflow soldering.
5. Suitable for high frequency circuit due to high
self-resonant frequency (4.8GHz of TZY2Z010 at
1.0pF setting).
Applications
1. Crystal oscillators 7. W-LAN
2. Crystal filters 8. Radar detectors
3. Stylus pen 9. Compact radios
4. Hand radios 10. Burglarproof devices
5. Watches 11. Headphone stereos
6. Remote keyless entry systems
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z010 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
Temperature Characteristics
TZY2Z010
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z2R5 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2Z2R5
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z030 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2Z030
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z060 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2Z060
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z100 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2Z100
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R200 (N750±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2R200
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R250 (N750±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2R250
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
K450 (N1000±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZY2K450
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
9
2
Z010
1000
100
Q
20 468
10
1
Frequency (GHz)
0.5pF set
1.0pF set
Frequency Characteristics
TZY2Z010
Z100
Q
1000
100
200 600400 800 1000
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZY2Z100
R200
Q
1000
100
200 1000600 800400
10
1
1000
100
10
Frequency (MHz)
Capacitance (pF)
TZY2R200
1000
100
10
1
1000
100
10
200 400 600 800
K450
Q
Capacitance (pF)
Frequency (MHz)
TZY2K450
(
Tolerance: ±0.1
in mm
)
4.0
2.4
1.2
Land Pattern
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
10
2
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
oReflow Soldering Profile
n
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to n
1 )
oSoldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
Temperature Profile
Notice (Storage and Operating Conditions)
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
11
2
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Notice (Soldering and Mounting)
Notice (Handling)
Notice (Other)
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
12
2
1. Soldering
(1) TZY2 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 120 micro m to 170 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(2.5mm external diameter and 1.2mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR020
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT020
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
(
Tolerance: ±0.1
in mm
)
2.0
1.6
3.2
2.0 dia.
4.5
-+
0.6 0.6
0.8
0.5±0.05
Depth 0.4±0.05
0.75
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZC3Z030AA01 1.4 3.0 +50/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc
TZC3Z060AA01 2.0 6.0 +50/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc
TZC3R100AA01 3.0 10.0 +50/-0% N750±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc
TZC3P200AA01 5.0 20.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc
TZC3P300AA01 6.5 30.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax. 100Vdc 220Vdc
Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85°C
Stator Electrode Terminal
Stator
Ceramic
Center Axis
Rotor Spring Terminal
Construction
Features
1. Small size with external dimension of
3.2(W)x4.5(L)x1.6(H)mm.
2. Can be adjusted with conventional adjustment tools
having a thickness of 0.5mm.
3. Designed for automatic placement in surface mount
applications.
4. Heat resistant resin withstands reflow soldering
temperatures.
Applications
1. Compact radios
2. Stylus pen
3. Portable radio equipment
4. Hybrid ICs
5. Remote keyless entry systems
Ceramic Trimmer Capacitors
TZC3 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
13
3
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z030 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
Temperature Characteristics
TZC3Z030
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z060 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZC3Z060
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R100 (N750±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZC3R100
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
P200 (N1200±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZC3P200
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
P300 (N1200±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZC3P300
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
14
3
Z030
1000
100
Q
100 500 1000 1500
Frequency (MHz)
2000
10
1
1000
100
10
Capacitance (pF)
Frequency Characteristics
TZC3Z030
Z060
Q
1000
100
100 500 2000
15001000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZC3Z060
R100
Q
1000
100
200 600400 800 1000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZC3R100
P200
Q
1000
100
200 1000600 800400
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZC3P200
(
Tolerance: ±0.1
in mm
)
3.3±0.1
1.0±0.1
5.0+0
-
0.5
Land Pattern
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
15
3
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
oReflow Soldering Profile
n
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to n
1 )
oSoldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
Temperature Profile
Notice (Storage and Operating Conditions)
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
16
3
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Notice (Soldering and Mounting)
Notice (Handling)
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
17
3
1. Soldering
(1) TZC3 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into the
movable part and/or the contact point. The
soldering iron should not come in contact with
the stator of the trimmer capacitor. If such
contact does occur, the trimmer capacitor may
be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
(8) When soldering the TZC3 series, the solder
should not flow into the staking part of the
substrate. If such flow does occur, driver slot
rotation will be damaged.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) Use a pick-up nozzle of a suitable dimension.
(2.5mm external diameter and 1.5mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
Recommended screwdriver for manual adjustment
Standard type --> MURATA: KMDR080
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
(
Tolerance: ±0.1
in mm
)
5.2±0.2
4.2±0.2
2.6 max.
2.8±0.2
3.0
2.2
0.6
1.6
0.4 Depth
0.3+0.1
-
0.2
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding Voltage
TZW4Z010A001 0.4 1.0 +50/-0% NP0±150ppm/°C 200min. at 500MHz, Cmax. 250Vdc 550Vdc
TZW4Z1R5A001 0.4 1.5 +100/-0% NP0±150ppm/°C 200min. at 500MHz, Cmax. 250Vdc 550Vdc
Insulation Resistance: 10000M ohm Torque: 1.5 to 10.0mNm Operating Temperature Range: -55 to +125°C
Cover
Metal Rotor
Monolithic Stator
Construction
Features
1. To meet high power application due to withstanding
voltage 550Vdc.
2. Extremely high self-resonant frequency.
(More than 3GHz at rated C max.)
3. Typical application: Impedance matching for Cellular
Base Station.
4. High Q value in more than VHF, UHF and Microwave
bands.
(More than 200 in 500MHz, C max.)
5. Available for pick and place machine. Possible
thinner design due to 2.6mm low profile.
6. Non-electrical contact construction
(rotor as middle electrode) provides high reliability.
7. Compact size: 4.2(W)x5.2(L)x2.6max.(H)mm.
Applications
1. Transmitting power amplifier for Cellular base station
2. Transmitting amplifier for PHS base station
3. High frequency electric circuit
4. High power radio transmission
5. Transponder amplifier for cable TV
Ceramic Trimmer Capacitors
TZW4 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
18
4
8
6
4
2
20–55 125
–2
–4
–6
–8
–10
–12
Z010 (NP0±150 ppm/°C)
Temp. (°C)
Cap. Change (%)
Temperature Characteristics
TZW4Z010
8
6
4
2
20–55 125
–2
–4
–6
–8
–10
–12
Z1R5 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZW4Z1R5
Z1R5
1000
100
Q
500 1000 1500 2000 2500 3000
10
1
Frequency (MHz)
1.5pF set
Frequency Characteristics
TZW4Z1R5
(
Tolerance: ±0.1
in mm
)
4.4
7.0
2.5
Land Pattern
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
oReflow Soldering Profile
n
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Standard Profile
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to n
1 )
oSoldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C
3sec. max. 30W max.
1 time
Cycle of soldering iron
Peak
temperature
(T5)
Peak
temperature
(T3)
Temperature Profile
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
19
4
Notice (Storage and Operating Conditions)
Notice (Soldering and Mounting)
1. Soldering
(1) TZW4 series can be soldered by reflow soldering
method and soldering iron. Do not use flow
soldering method (dipping).
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
(5) When using soldering iron, the diameter of the
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
the contact failure due to flux invasion into
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0 N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breaking.
(3) Use a pick-up nozzle of a suitable dimension.
(4.0mm external diameter and 1.2mm bore
diameter.)
3. Cleaning
This product cannot be cleaned because of open
construction.
Notice (Handling)
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
20
4
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30
to 85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(Ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (Ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
1. Use suitable screwdrivers that fit comfortably in
driver slot.
-Recommended screwdriver for manual adjustment
VESSEL : No.9000 -1.3x30
(Murata P/N is KMDR130)
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
(
Tolerance: ±0.5
in mm
)
5.0
2.7±0.3
4.0±0.2
2.4±0.1
4.5±0.2
0.6±0.1 Depth 0.5 1.4±0.1 dia.
3.0±0.2
1.2±0.1
A Type
(
Tolerance: ±0.5
in mm
)
4.0±0.2
2.4±0.1
3.0±0.2
4.5±0.2
7.0
1.2±0.1
0.6±0.1 Depth 0.5 1.4±0.1 dia.
B Type
Part Number C min. (max.)
(pF)
C max.
(pF) TC Q Rated Voltage Withstanding
Voltage Stator/Case Color
TZB4Z030pp10
1.4 3.0 +50/-0% NP0±200ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Brown
TZB4Z060pp10
2.0 6.0 +50/-0% NP0±200ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue
TZB4Z100pp10
3.0 10.0 +50/-0% NP0±300ppm/°C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White
TZB4R200pp10
4.5 20.0 +50/-0% N750±400ppm/°C 500min. at 1MHz, Cmax 100Vdc 220Vdc Red
TZB4P300pp10
6.5 30.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Green
TZB4P400pp10
8.5 40.0 +50/-0% N1200±500ppm/°C 300min. at 1MHz, Cmax 100Vdc 220Vdc Yellow
TZB4Z250pp10
4.0 25.0 +100/-0% NP0±300ppm/°C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black+Marking
TZB4R500pp10
7.0 50.0 +100/-0% N750±300ppm/°C 300min. at 1MHz, Cmax 50Vdc 110Vdc Black+Marking
Features
1. Miniature rectangular shape:
4.0(W)x4.5(L)x3.0(H)mm.
2. Color coded case facilitates identification of
capacitance range.
3. Designed for automatic placement in surface mount
applications.
4. Designed to withstand flux baths and solder baths
(with cover film type).
5. Can be temporarily attached to PCB with adhesives
(Terminal style A and B).
6. Can be reflow and flow (with cover film type)
soldering method.
7. Stable characteristics over a wide frequency range.
(Resonant frequency: 1000MHz min. / 6pF)
Applications
1. Car audio systems
2. Hybrid ICs
3. Remote keyless entry systems
4. Surveillance cameras
5. Burglarproof devices
6. Entry phone
Ceramic Trimmer Capacitors
TZB4 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
21
5
Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85°C
First blank: Terminal Type Second blank: Cover film codes (A: not provided, B: provided)
rex. TZB4Z100A B10: Terminal Type is A, and Cover film is provided.
Plastic Case
Rotor Spring
Metal Rotor
Ceramic Plate
Stator Terminal
Cover Film (Cover film type)
Rotor Terminal
–
+
Construction
2.4±0.2
1.6±0.1
(in mm)
7.0+0
-
0.5
Land Pattern/Mounting Holes
A Type
8.0+0
-
0.5
4.0±0.2
1.6±0.1
(in mm)
B Type
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
Z030 (NP0±200 ppm/°C)
Temp. (°C)
Cap. Change (%)
Temperature Characteristics
TZB4Z030
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
Z060 (NP0±200 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4Z060
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z100 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4Z100
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R200 (N750±400 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4R200
Continued on the following page.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
22
5
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
P300 (N1200±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4P300
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
P400 (N1200±500 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4P400
Continued from the preceding page.
Temperature Characteristics
8
6
4
2
20
–25 85
–2
–4
–6
–8
–10
–12
Z250 (NP0±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4Z250
8
6
4
2
20–25 85
–2
–4
–6
–8
–10
–12
R500 (N750±300 ppm/°C)
Temp. (°C)
Cap. Change (%)
TZB4R500
Z060
1000
100
Q
10
1000
100
10
800700600500400300200100 900 1000
Frequency (MHz)
1
Capacitance (pF)
Frequency Characteristics
TZB4Z060
Z100
Q
1000
100
800700600500400300200100 900 1000
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4Z100
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
23
5
R200
Q
1000
100
200100 400300 500 600
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4R200
R500
Q
1000
100
100 500300 400200
Frequency (MHz)
10
1
1000
100
10
Capacitance (pF)
TZB4R500
Temperature (°C)
t3
t2
T3
T2
T5
T4
T1
time (s)
t1
Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
Temperature (°C)
t1
t2
T3
T2
T1
time (s)
Limit Profile
Standard Profile
n
1 Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu)
Limit Profile
Standard Profile
F4'* *#$-02#0+',*1&.#AA,"@
F++#01#2&# -"7',1-*"#0 2&A4'* *#$-0!-4#0q*+27.#@
Standard Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time150°C 60 to 120sec. 250°C 5sec. max.
Temperature (°C)
time (s)
Standard Profile
t1
T1 t2
T3
T2
n
2 Soldering profile for Eutectic solder (63Sn/37Pb)
(Limit profile: refer to n
1 )
oFlow Soldering Profile
oReflow Soldering Profile
Cycle
of reflow
Limit Profile
Pre-heating Heating
Temp. (T1) Time (t1) Temp. (T3) Time (t2)
2 times150°C 60 to 120sec. 265±3°C 5sec. max.
Cycle
of reflow
Standard Profile
Pre-heating Heating
Peak
temperature
(T3)
Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
2 times245±3°C
150 to 180°C 60 to 120sec.
220°C
30 to 60sec.
Limit Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T4) Time (t3)
2 times
260 +5/-0°C
150 to 180°C 60 to 120sec.
230°C
30 to 50sec.
Peak
temperature
(T5)
Standard Profile
Pre-heating Heating Cycle
of reflow
Temp. (T1) Time (t1) Temp. (T2) Time (t2)
1 time
230 +5/-0°C
150°C
60 to 120sec.
183°C 30sec.
Peak
temperature
(T3)
oSoldering Iron
Standard Profile
Temperature of soldering iron tip Soldering time Soldering iron power output
350±10°C 3sec. max. 30W max. 1 time
Cycle of soldering iron
Temperature Profile
Notice (Storage and Operating Conditions)
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
24
5
1. Do not use the trimmer capacitor under atmosphere
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
2. Before using trimmer capacitors, please store under
the conditions of -10 to +40°C and 30 to
85%RH.
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
6. Do not use the trimmer capacitor under the
conditions listed below.
(1) Corrosive gasses atmosphere
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
(2) In liquid (ex. water, oil, medical liquid,
organic solvent, etc.)
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage or electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Notice (Soldering and Mounting)
Notice (Handling)
1. Use suitable screwdrivers that fit comfortably in
driver slot.
(1) Recommended screwdriver for manual adjustment
MURATA: KMDR010
(2) Recommended screwdriver bit for automatic
adjustment
MURATA: KMBT010
2. When adjusting with a screwdriver, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. Excessive force applied
to the screwdriver slot may cause deformation of the
products.
3. Do not apply adhesive, lock paints, or any other
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
4. Do not break the cover film before the completion
of PCB mounting, soldering, and cleaning.
5. Do not clean the trimmer capacitor after the cover
film has been broken.
6. To break the cover film, first turn the screwdriver
more than 360°, and set the capacitance value.
(Inserting the screwdriver only will not break the
cover film.)
Notice (Other)
Before using trimmer capacitors, please test after
assembly in your particular mass production system.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
25
5
1. Soldering
(1) Can be soldered by reflow soldering method, flow
soldering method, and soldering iron.
(2) Soldering conditions
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
(5) When using soldering iron, the string solder
shall be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or contact failure
due to flux invasion into the movable part and/or
the contact point. The soldering iron should not
come in contact with the plastic case of the
trimmer capacitor. If such contact does occur,
the trimmer capacitor may be damaged.
(6) Our recommended chlorine content of solder is
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
(7) Do not use water-soluble flux (for water
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
2. Mounting
(1) Do not apply excessive force (preferably 5.0N
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
(2) Do not warp and/or bend PCB to protect trimmer
capacitor from breakage.
(3) When bending the terminals, do not apply
excessive force to the body of the product to
protect the terminal fixing part from damage.
(4) Use a pick-up nozzle of a suitable dimension.
> Without cover film type
- External dimensions of 4.5x4.0mm and
2.5mm bore diameter.
> With cover film type
- 4.0mm external diameter and 2.0mm bore
diameter.
3. Cleaning [with cover film type]
Isopropyl alcohol and ethyl alcohol are available
material for cleaning. If you use any other type of
solvent, please evaluate performance in your
application. Moreover, please confirm that no
damage has occurred to the trimmer capacitor
after cleaning in your conditions.
4. Other
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
Packaging
Part Number
TZR1
TZY2
TZC3
TZW4
TZB4
3000
2000
1000
500
500
ø180mm Reel
-
-
-
-
2500
ø330mm Reel
500
500
500
100
500
Bulk
Minimum Quantity (pcs.)
Minimum Quantity
2.0±0.2
8.0±0.3
3.5±0.1
1.8±0.2
1.75±0.1
0.25±0.1
1.05±0.2
4.0±0.14.0±0.1
(in mm)
2.0±0.1
1.5+0.1
-
0dia.
Tape Dimensions
TZR1 Series
(
Tolerance: ±0.1
in mm
)
4.02.0
3.5
8.0±0.2
3.6±0.2
4.0
2.7±0.2
t
0.25
1.75
1.5+0.1
-
0dia.
A-Across
section
t=TZY2 (TZVY2): 1.6±0.2
A
A
TZY2 Series
(
Tolerance: ±0.1
in mm
)
4.9±0.2
12±0.3
5.5
8 3.6±0.2
42 0.3
2.0±0.2
1.75
1.5+0.1
-
0dia.
A-Across
section
A
A
TZC3 Series
(
Tolerance: ±0.1
in mm
)
42
5.6
12±0.2
5.5
84.6
1.75
2.6
0.3
A-Across
section
A
A
1.5+0.1
-
0dia.
TZW4 Series
(
Tolerance: ±0.1
in mm
)
8.0 2.0 4 .0
5.5
12.0±0.3
7.5
4.8
4.3
1.8
0.3±0.1
3.55±0.2
1.75
1.5+0.1
-
0dia.
A
A
Direction of feed
A-Across
section
TZB4 Series
Continued on the following page.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
26
Packaging
Continued from the preceding page.
50 min.
178±2 dia.
13.0±1.0
9.0±1.0
(in mm)
2.0±0.5
21.0±0.8 dia.
13.0±0.5 dia.
Reel Dimensions (180mm diameter)
TZR1/TZY2 Series
50 min.
178±2 dia.
17.0±1.0
13.0±1.0
(in mm)
2.0±0.5
21.0±0.8 dia.
13.0±0.5 dia.
TZC3/TZW4/TZB4 Series
50 min.
328±2 dia.
17.5±1.0
13.5±1.0
(in mm)
2.0±0.5
21.0±0.8 dia.
13.0±0.5 dia.
Reel Dimensions (330mm diameter)
TZB4 Series
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
27
Recommended Adjustment Tools
For Manual Adjustment
Series MURATA
Model Number
Manufacturer’s
Model Number Shape
TZR1
TZY2
TZC3
TZB4
TZW4
KMDR160
KMDR020
KMDR080
KMDR010
KMDR130
MURATA MFG.
KMDR160
VESSEL MFG.
NO.9000 -0.9x30
VESSEL MFG.
NO.9000 +1.7x30
MURATA MFG.
KMDR010
VESSEL MFG.
NO.9000 -1.3x30
Please use the following recommended screwdrivers.
You can order these drivers using the part numbers below.
Although you can also adjust the capacitance value using commercial products, please use one with the same head size as the
driver listed below.
For Automatic Adjustment
TZY2
TZB4
KMBT020
KMBT010
MURATA MFG.
KMBT020
MURATA MFG.
KMBT010
Series MURATA
Model Number
Manufacturer’s
Model Number Shape
(in mm)
(in mm)
Bit shape: Minus (2.2x0.4)
(in mm)
Bit shape: Minus (0.3x0.13)
(in mm)
(in mm)
(in mm)
Bit shape: Minus (2.2x0.4)
(in mm)
Bit shape: Minus (1.3x30)
Bit shape: Plus (1.7x30)
Bit shape: Minus (0.9x30)
80
125
15
125
125
15
15
122
5020
1.5
30
2.2 dia.
25.0
10.0
5.03.0
0.6±0.05
0.9±0.05
ø2.0
ø2.4
0.4±0.05
0.2±0.05
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
28
MURATA FACTORY
Sabae Murata Mfg. Co., Ltd.
The products listed herein have been produced
by a ISO9001 certified factory.
* No ODCs (Ozone Depleting Chemicals) are used on
any Murata trimmer capacitors.
T13E.pdf
Sep.1,2017
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
29
Qualified Standards
Murata Manufacturing Co., Ltd.
www.murata.com
Note
1 Export Control
For customers outside Japan:
No Murata products should be used or
sold, through any channels, for use in the
design, development, production, utilization,
maintenance or operation of, or otherwise
contribution to (1) any weapons (Weapons of
Mass Destruction [nuclear, chemical or biological
weapons or missiles] or conventional weapons)
or (2) goods or systems specially designed or
intended for military end-use or utilization by
military end-users.
For customers in Japan:
For products which are controlled items subject
to the “Foreign Exchange and Foreign Trade Law”
of Japan, the export license specifi ed by the law
is required for export.
2 Please contact our sales representatives or
product engineers before using the products in
this catalog for the applications listed below,
which require especially high reliability for the
prevention of defects which might directly
damage a third party’s life, body or property, or
when one of our products is intended for use
in applications other than those specified in
this catalog.
1 Aircra equipment
2 Aerospace equipment
3 Undersea equipment
4 Power plant equipment
5 Medical equipment
6 Transportation equipment (vehicles, trains,
ships, etc.)
7 Tra c signal equipment
8 Disaster prevention / crime prevention
equipment
9 Data-processing equipment
10 Application of similar complexity and/or
reliability requirements to the applications
listed above
3 Product specifi cations in this catalog are as of
September 2017. They are subject to change or
our products in it may be discontinued without
advance notice. Please check with our sales
representatives or product engineers before
ordering. If there are any questions, please contact
our sales representatives or product engineers.
4 Please read rating and CAUTION (for storage,
operating, rating, soldering, mounting and
handling) in this catalog to prevent smoking
and/or burning, etc.
5 This catalog has only typical specifi cations.
Therefore, please approve our product
specifi cations or transact the approval sheet
for product specifi cations before ordering.
6 Please note that unless otherwise specifi ed, we
shall assume no responsibility whatsoever for any
confl ict or dispute that may occur in connection
with the e ect of our and/or a third party’s
intellectual property rights and other related
rights in consideration of your use of our products
and/or information described or contained in our
catalogs. In this connection, no representation
shall be made to the e ect that any third parties
are authorized to use the rights mentioned above
under licenses without our consent.
7 No ozone depleting substances (ODS) under the
Montreal Protocol are used in our manufacturing
process.
Global Locations
For details please visit www.murata.com
Cat. No. T13E-17
T13E.pdf
Sep.1,2017
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Murata:
TZC3P200A310B00 TZC3P200A310R00 TZB4Z250BA10R01 TZB4Z250EA10R01 TZB4Z250AA10R01
TZB4Z250BA10R00 TZB4Z250EA10R00 TZB4Z250AA10R00 TZB4Z250DA10B00 TZB4Z250BA10B00
TZB4Z250CA10B00 TZB4Z250AA10B00 TZB4Z250EA10B00 TZR1Z040A001B00 TZB4P300CA10B00
TZB4P300EA10B00 TZB4P300AA10B00 TZB4P300BA10B00 TZB4P300DA10B00 TZB4P300BA10R01
TZB4P300AA10R01 TZB4P300EA10R01 TZB4P300BA10R00 TZB4P300AA10R00 TZB4P300EA10R00
TZR1Z040A001R00 TZR1Z010A001B00 TZR1Z010A001R00 TZB4Z100EB10R01 TZB4Z100AB10R01
TZB4Z100BB10R01 TZB4Z100EB10R00 TZB4Z100AB10R00 TZB4Z100BB10R00 TZY2K450A001R00
TZB4Z100DB10B00 TZB4Z100BB10B00 TZB4Z100CB10B00 TZB4Z100EB10B00 TZB4Z100AB10B00
TZB4R500AB16R00 TZY2K450A001B00 TZR1R080A001B00 TZR1R080A001R00 TZY2P450A001R00
TZB4Z030EA10B00 TZB4Z030AA10B00 TZB4Z030CA10B00 TZB4Z030DA10B00 TZB4Z030BA10B00
TZB4Z030BA10R01 TZB4Z030AA10R01 TZB4Z030EA10R01 TZB4Z030BA10R00 TZB4Z030AA10R00
TZB4Z030EA10R00 TZC3P200A110B00 TZC3P200A110R00 TZB4Z060BA10B00 TZB4Z060DA10B00
TZB4Z060AA10B00 TZB4Z060EA10B00 TZB4Z060CA10B00 TZB4Z060BA10R01 TZB4Z060AA10R01
TZB4Z060EA10R01 TZB4Z060BA10R00 TZB4Z060AA10R00 TZB4Z060EA10R00 TZC3Z030A110R00
TZC3Z030A110B00 TZC3R100A310R00 TZY2Z100A001B00 TZY2Z060A001R00 TZY2Z030A001B00
TZY2Z030A001R00 TZC3Z060A110R00 TZY2Z010A001B00 TZY2Z010A001R00 TZC3Z060A110B00
TZB4Z030EB10B00 TZB4Z030AB10B00 TZB4Z030CB10B00 TZB4Z030DB10B00 TZB4Z030BB10B00
TZC3P200A110R01 TZW4Z1R5A001R00 TZY2R250A001R00 TZY2R250A001B00 TZC3R100A110B00
TZC3R100A110R00 TZB4P400EA10R01 TZB4P400AA10R01 TZB4P400BA10R01 TZB4P400EA10R00
TZB4P400AA10R00 TZB4P400BA10R00 TZY2R200A001R00 TZY2R200A001B00 TZB4P400BA10B00