O1007 MS PC 20061128-S00006 No. A0649-1/8
http://onsemi.com
Semiconductor Components Industries, LLC, 2013
June, 2013
LV8080LP
Overview
The LV8080LP is a two-channel con s tant-current driver that supports low-voltage operatio n. It is optimal for
constant-current drive of stepping motors (AF and zoom) in portable equipment such as camera cell phones.
Features
Two channels constant-current H-bridge driver
Built-in power supply switch and position detection co mparator for use with a photoreflector
Supports both 2-phase drive and 1-2 phase drive.
Implemented in a low-power MOS IC process.
Ultraminiature easy to solder VCT16 package (2.6 × 2.6mm)
Built-in thermal protection and low-voltage sensing circuits
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage VCC, VM max 6.5 V
Output voltage VOUT max OUT1, OUT2, OUT3, OUT4 6.5 V
Input voltage VIN max CONT, IN -0.3 to +6.5 V
Ground pin source current IGND Per channel 400 mA
Allowable power dissipation Pd max Mounted on a circuit board.* 700 mW
Operating temperature Topr -30 to +85 °C
Storage temperature Tstg -40 to +150 °C
* Specified circuit board : 40×50×0.8mm3 : 4-layer (2S2P) glass epoxy printed circuit board
Bi-CMOS LSI
Two channels Constant-current
H-bridge Driver
Orderin
g
numbe
r
: ENA0649
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
C onditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
LV8080LP
No.A0649-2/8
Allowable Operating Ratings at Ta = 25°C
Parameter Symbol Conditions Ratings Unit
Supply voltage VCC 2.5 to 6.0 V
High-level input voltage VIH 0.6VCC or more V
Low-level input voltage VIL
CONT, IN
Up to 0.2VCC V
Electrical Characteristics at Ta = 25°C, VCC = 3.0V
Ratings
Parameter Symbol Conditions min typ max
Unit
ICCO EN = 0V 0.1 1 μA Current drain
ICCO1 EN = 3V 0.7 1 mA
Ron1 VCC = 3.0V (High and low side total)
EN = 3.0V, IOUT = 100mA 2.0 3.0 Ω Output on resistance
Ron2 VCC = 5.0V (High and low side total)
EN = 5.0V, IOUT = 100mA 1.50 2.0 Ω
Constant-current output 1 IOUT1 Between RFG and ground : 1Ω 95 100 105 mA
Constant-current output 2 IOUT2 Between RFG and ground : 0.5Ω
(Design specification) 190 200 210 mA
Output turn-on time Traise With RFG1 and RFG2 shorted to ground
(Design specification) 1.3 3 μs
Output turn-off time Tfall With RFG1 and RFG2 shorted to ground
(Design specification) 0.25 0.65 μs
Position detection voltage
(high level) VH 1.0 1.06 V
Position detection voltage
(low level) VL 0.74 0.8 V
Detection voltage hysteresis HYS 0.165 0.18 0.195 V
PI/PR pin current IPI/PR 20 mA
Input current IIN V
IN = 3V 15 30 μA
Note : The design specification items are design guarantees and are not measured.
Package Dimensions Pin Assignment
unit : mm (typ) (VCT16)
3318
2.6
2.6
0.4
0.8
0.25
(0.035)
SIDE VIEW
SIDE VIEW
BOTTOM VIEW
TOP VIEW
LASER MARKED
INDEX 0.5
(0.55)
(C0.116)
(0.13)
(0.125)
12
16
SANYO : VCT16(2.6X2.6)
RFG1
OUT1
OUT2
OUT3
OUT4 IN2
CONT
GND
COMPIN
PI/PR
(Top View)
1
16 15 14 13
5 6 7 8
2
3
4
12
11
10
9
RFG2 IN3 IN4 IN1
VCC COMPOUT
LV8080LP
No.A0649-3/8
Block Diagram
Constant-current calculation : IOUT = 0.1 ÷ RF Example : When an IOUT of 100mA is required, RF must be 1Ω.
Usage Notes
The constant current is set by the resource RF connected between RFG and grou nd according to t he fo r mula shown
above.
Truth Table
Input Output
IN1 IN2 IN3 IN4 OUT1 OUT2 OUT3 OUT4 Mode
Low Low Low Low Off Off Off Off Standby mode
Low High Low High Channel 1, reverse
High Low High Low Channel 1, forward
High High
- -
Low Low
Off Off
Channel 1, brake mode
Low High Low High Channel 2, reverse
High Low High Low Channel 2, forward
- -
High High
Off Off
Low Low Channel 2, brake mode
Note : The "-" input unstable state. When off, a high-impedance state.
• The ENA goes to the standby state with a low-level input, and to the operating state with a high-level input.
• The control input switches the forward/reverse mode.
VCC
0.1V
RFG2
IN1
IN2
IN3
IN4
LVS TSD
VM
PI/PR
RFG1
CONT
STM
1.0V
COMPOUTCOMPIN GND
L
O
G
I
C
LV8080LP
No.A0649-4/8
Pin Description
Pin No. Pin Name Description Equivalent Circuit
1
2
3
4
5
16
OUT1
OUT2
OUT3
OUT4
RFG2
RFG1
1-4 : Output pins
H-bridge type output pins
Pins 1 and 2 are paired and pins 3 and 4 are paired.
5, 16 : Current sensing resistor connection pins
Connect the current sensing resistor between these
pins and ground to detect the output currents for
constant curr ent control.
Pin 16 correspon ds to the out put from pins 1 and 2 and
pin 5 to the output from pins 1 and 2.
-
+
10kΩ
0.1V
VCC
1
5
2
6
7
8
9
10
IN3
IN4
IN1
IN2
CONT
Logic input pins
10kΩ
200kΩ
VCC
GND
6
11 GND Ground
12 COMPIN Photo reflector position sensing comparator input
VCC
1kΩ
GND
12
13 COMPOUT Photo reflector position sensing comparator output
This pin serves as an open-collector output of the NPN
transistor.
1kΩ
GND
13
Continued on nex t pa ge.
LV8080LP
No.A0649-5/8
Continued from preceding page.
Pin No. Pin Name Description Equivalent Circuit
14 PI/PR A switch, with NMOS open-drain output, used to turn
on/off the power supply of the position sensor unit. When
using this switch, connect the position sensor unit
between this pin and the VCC pin.
On/off control of this switch is accomplished by CONT
pin. Setting the CONT pin high turns on the switch.
6
VCC
GND
15 VCC Power supply pin
Timing Chart
(1) Stepper motor timing chart
Timing chart for 2-phase drive
(2) Timing chart for 1-2 phase drive (Slow decay mode)
Channel 1
output mode
IN1
IN3
IIN2
IN4
Forward
Standby
Standby
Reverse Forward Standby
StandbyForward Reverse
Forward
Channel 2
output mode
Channel 1
output mode
IN1
IN3
IIN2
IN4
Channel 2
output mode
Forward Reverse
Forward Reverse
Forward
Brake
Brake Brake
BrakeStandby
Standby
Reverse Forward Standby
StandbyForward Reverse
Forward
LV8080LP
No.A0649-6/8
Photosensor Position Detection Application Circui t Example
(a) Application circuit
(b) Timing chart
VCC
VCC
CONT
COMPIN
1.00V Hysteresis : 0.2 V
Microcontroller
power supply
Transistor drive region
COMPOUT
PI/PR
COMPIN
VCC
COMPOUT
10kΩ
Tr
IC peripheral circuits : Position sensor block
Sensor power supply Microcontrolle
r
power supply
IC internal circuits :
Position detection circuit
LV8080LP
No.A0649-7/8
01234567 3 4 5 6128
01234567
Supply voltage, VCC –V
Current drain, ICCO –nA
0
0.5
0.1
0.2
0.3
0.4
0.6
0.7
0.8
0.9
1.1
1.2
1.3
1.4
1
1.5
0 0.3 0.4 0.50.1 0.2 0.6
Output current, IO–A
Vsat V
Position detection circuit threshold voltage
0
0.5
1
1.5
2
2.5
3
3.5
0.8 0.85 0.950.9 1 1.05
Input voltage, VIN –V
Output voltage, VO–V
PI/PR pin current (VCC = 3V/5V)
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02
PI/PR pin current A
PI/PR pin voltage V
0.095
0.096
0.097
0.098
0.099
0.1
0.101
0.102
0.103
0.104
0.105
0345612 7
Supply voltage, VCC –V
Output current, IO–A
07
Supply voltage, VCC –V
Current drain, ICCO1–mA
ICCO – VCC
Supply voltage, VCC –V
Input current, IIN μA
Input current (VIN = 3V)
ICCO1 – VCC
Output on resistance (High and low side total)
Constant-current output (Between RFG and ground : 1Ω)
VCC = 3V
VCC = 3V
VCC = 5V
VCC = 5V
0
10
20
30
40
50
60
70
80
90
100
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0
5
10
15
20
25
30
35
40
45
50
LV8080LP
PS No.A0649-8/8
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLCs product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representationor guarantee regarding the suitabilityof its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture ofthe
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ON Semiconductor:
LV8080LP-E LV8080LPGEVB