NSVS1106 Feb-04
Application
440MHz SAW FILTER
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 1. Electrical Specifications
Item Spec.
Input and Output Impedance 50Ω
Nominal Center Frequency (f0) 440MHz
Insertion Loss 439.5~440.5MHz 3.5dB max.
Response Variation 439.5~440.5MHz 1.5dB max.
Input and Output VSWR 439.5~440.5MHz 2.5 max.
418.6 MHz 50dB min. Out of Band Rejection
(Relative to Through Level) 461.4 MHz 45dB min.
Temperature Range: -10~+60ºC
Table 2. Maximum Ratings
Item Rating
Maximum Input Power +20dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -10~+60ºC
Storage Temperature -20~+70ºC
JRC SAW FILTER
NSVS1106
Communications Equi pment Division
Communications Equi pment Marketing Department
10-1 Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo. 160-8328 Japan
Tel. +81 3-3348-3 845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
http://www.jrc.co.jp/eng/product/comm/device/saw/saw_top_e.html (English)
NSVS1106 Feb-04
マーキング方法・・・レーザーマーカー
表示内容
(１)製造年（西暦の下１ｹﾀ）
(２)製造月
但し 10月…X
11月…Y
12月…Z
(３)製造日
但し 1〜9日…0
10〜19日…1
20〜31日…2
(４)品種種別記号
Ｎo. 接 続
１ ＧＮＤ
２ ＩＮ／ＯＵＴ
３ ＧＮＤ
４ ＧＮＤ
５ ＯＵＴ／ＩＮ
６ ＧＮＤ
Fig.1 Measuring circuit
Fig.2 Package dimensions (in mm)
Fig.3 Desirable land area (in mm)
1
2
34
5
6
SAW
IN
50Ω OUT
50Ω
0.93
0.6
0.93 3.8
3.8
2.2 1.15
1.15
４２０
ＸＥ
(0.6)
(0.25)
(0.6)
(0.53)
[4×]
(0.75)
[6
×
]
(0.45)
１
２
３４
５
６
1.15±0.15
3.0±0.15
3.0±0.15
(１)
(３)
(２)
(1.8)
(４)
NSVS1106 Feb-04
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -10ºC or more than +60ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of so ldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static e lectricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
440MHz SAW Filter
FREQUENCY CHARACTERISTICS
S22S11
0
10
20
30
40
50
60
70
80
90
390.0 400.0 410.0 420.0 430.0 440.0 450.0 460.0 470.0 480.0 490.0
Frequency [ MHz]
Insertion Loss [dB]
0
1
2
3
4
5
6
7
8
9
S11
1
2
3
4
5
6
7
8
9
10
11
430 434 438 442 446 450
Frequency [MHz]
VSWR
S22
1
2
3
4
5
6
7
8
9
10
11
430 434 438 442 446 450
Frequency [MHz]
VSWR
