ISSI (R) IS41LV16400 4M x 16 (64-MBIT) DYNAMIC RAM WITH EDO PAGE MODE NOVEMBER 1999 FEATURES DESCRIPTION * Extended Data-Out (EDO) Page Mode access cycle The ISSI IS41LV16400 is 4,194,304 x 16-bit high-performance CMOS Dynamic Random Access Memories. These devices offer an accelerated cycle access called EDO Page Mode. EDO Page Mode allows 1,024 random accesses within a single row with access cycle time as short as 20 ns per 16-bit word. The Byte Write control, of upper and lower byte, makes the IS41LV16400 ideal for use in 16-bit wide data bus systems. * TTL compatible inputs and outputs; tristate I/O * Refresh Interval: 4,096 cycles / 64 ms * Auto refresh Mode: RAS-Only, CAS-before-RAS (CBR), and Hidden * Low Standby power dissipation: - 1.8mW(max) CMOS Input Level * Single power supply: 3.3V 10% * Byte Write and Byte Read operation via two CAS * Extended Temperature Range -30oC to 85oC These features make the S41LV16400 ideally suited for high-bandwidth graphics, digital signal processing, high-performance computing systems, and peripheral applications. * Industrail Temperature Range -40 C to 85 C The IS41LV16400 is packaged in a 50-pin TSOP (Type II). JEDEC standard pinout. PIN CONFIGURATION PIN DESCRIPTIONS o o 50-Pin TSOP (Type II) A0-A11 Address Inputs I/O0-15 Data Inputs/Outputs VCC 1 50 GND I/O0 2 49 I/O15 WE Write Enable I/O1 3 48 I/O14 OE Output Enable I/O2 4 47 I/O13 I/O3 5 46 I/O12 RAS Row Address Strobe VCC 6 45 GND UCAS Upper Column Address Strobe I/O4 7 44 I/O11 I/O5 8 43 I/O10 LCAS Lower Column Address Strobe I/O6 9 42 I/O9 Vcc Power I/O7 10 41 I/O8 NC 11 40 NC GND Ground VCC 12 39 GND NC No Connection W 13 38 LCAS RAS 14 37 UCAS NC 15 36 OE NC 16 35 NC NC 17 34 NC NC 18 33 NC Parameter -50 -60 Unit A0 19 32 A11 A1 20 31 A10 Max. RAS Access Time (tRAC) 50 60 ns A2 21 30 A9 Max. CAS Access Time (tCAC) 13 15 ns A3 22 29 A8 A4 23 28 A7 Max. Column Address Access Time (tAA) 25 30 ns A5 24 27 A6 Min. EDO Page Mode Cycle Time (tPC) 20 25 ns VCC 25 26 GND Min. Read/Write Cycle Time (tRC) 84 104 ns KEY TIMING PARAMETERS ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. (c) Copyright 1999, Integrated Silicon Solution, Inc. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 1 ISSI IS41LV16400 (R) FUNCTIONAL BLOCK DIAGRAM OE WE LCAS UCAS CAS CLOCK GENERATOR WE CONTROL LOGICS CAS WE OE CONTROL LOGIC OE RAS CLOCK GENERATOR RAS DATA I/O BUS COLUMN DECODERS SENSE AMPLIFIERS ADDRESS BUFFERS A0-A11 2 ROW DECODER REFRESH COUNTER DATA I/O BUFFERS RAS I/O0-I/O15 MEMORY ARRAY 4,194,304 x 16 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) TRUTH TABLE Function Standby Read: Word Read: Lower Byte RAS H L L LCAS H L L UCAS H L H WE X H H OE X L L Address tR/tC X ROW/COL ROW/COL Read: Upper Byte L H L H L ROW/COL Write: Word (Early Write) Write: Lower Byte (Early Write) L L L L L H L L X X ROW/COL ROW/COL Write: Upper Byte (Early Write) L H L L X ROW/COL L L L L L L L L LHL LHL L H L L H L HL LH HL HL HL HL L L H L L H L HL LH HL HL HL HL L L H L HL H H H L L HL HL H L X X LH L L L X X LH LH L X X X ROW/COL ROW/COL NA/COL NA/COL ROW/COL NA/COL ROW/COL NA/COL ROW/COL ROW/COL ROW/NA X Read-Write(1,2) EDO Page-Mode Read(2) 1st Cycle: 2nd Cycle: Any Cycle: EDO Page-Mode Write(1) 1st Cycle: 2nd Cycle: EDO Page-Mode(1,2) 1st Cycle: Read-Write 2nd Cycle: Hidden Refresh Read(2) Write(1,3) RAS-Only Refresh CBR Refresh(4) I/O High-Z DOUT Lower Byte, DOUT Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DOUT DIN Lower Byte, DIN Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DIN DOUT, DIN DOUT DOUT DOUT DIN DIN DOUT, DIN DOUT, DIN DOUT DOUT High-Z High-Z Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. EARLY WRITE only. 4. At least one of the two CAS signals must be active (LCAS or UCAS). Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 3 ISSI IS41LV16400 (R) FUNCTIONAL DESCRIPTION Refresh Cycle The IS41LV16400 is a CMOS DRAM optimized for high-speed bandwidth, low power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 22 address bits: 12 row address bits (A0~A11) and 10 column address bits (A0~A9). The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first twelve bits and CAS is used the latter ten bits. To retain data, 4,096 refresh cycles are required in each 64 ms period. There are two ways to refresh the memory. The IS41LV16400 has two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generates a CAS signal functioning in an identical manner to the single CAS input on the other 4M x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 through I/O7 and UCAS controls I/O8 through I/O15. The IS41LV16400 CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IS41LV16400 both BYTE READ and BYTE WRITE cycle capabilities. Memory Cycle A memory cycle is initiated by bring RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensures proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tRAS time has expired. A new cycle must not be initiated until the minimum precharge time tRP, tCP has elapsed. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tAR. Data Out becomes valid only when tRAC, tAA, tCAC and tOEA are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. Write Cycle A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs last. 4 1. By clocking each of the 4,096 row addresses (A0 through A11) with RAS at least once every 64 ms. Any read, write, read-modify-write or RAS-only cycle refreshes the addressed row. 2. Using a CAS-before-RAS refresh cycle. CAS-before-RAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 12-bit counter provides the row addresses and the external address inputs are ignored. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Extended Data Out Page Mode EDO page mode operation permits all 1,024 columns within a selected row to be randomly accessed at a high data rate. In EDO page mode read cycle, the data-out is held to the next CAS cycle's falling edge, instead of the rising edge. For this reason, the valid data output time in EDO page mode is extended compared with the fast page mode. In the fast page mode, the valid data output time becomes shorter as the CAS cycle time becomes shorter. Therefore, in EDO page mode, the timing margin in read cycle is larger than that of the fast page mode even if the CAS cycle time becomes shorter. In EDO page mode, due to the extended data function, the CAS cycle time can be shorter than in the fast page mode if the timing margin is the same. The EDO page mode allows both read and write operations during one RAS cycle, but the performance is equivalent to that of the fast page mode in that case. Power-On After application of the VCC supply, an initial pause of 200 s is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with VCC or be held at a valid VIH to avoid current surges. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) ABSOLUTE MAXIMUM RATINGS(1) Symbol VT VCC IOUT PD TA TSTG Parameters Voltage on Any Pin Relative to GND Supply Voltage Output Current Power Dissipation Commercial Operation Temperature Extended Temperature Industrail Temperature Storage Temperature Rating -0.5 to +4.6 -0.5 to +4.6 50 1 0 to +70 -30 to +85 -40 to +85 -55 to +125 Unit V V mA W C C C C Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND.) Symbol VCC VIH VIL TA Parameter Supply Voltage Input High Voltage Input Low Voltage Commercial Ambient Temperature Extended Ambient Temperature Industrail Ambient Temperature Min. 3.0 2.0 -0.3 0 -30 -40 Typ. 3.3 -- -- -- -- -- Max. 3.6V VCC + 0.3 0.8 70 85 85 Unit V V V C C C CAPACITANCE(1,2) Symbol Parameter CIN1 CIN2 CIO Input Capacitance: A0-A11 Input Capacitance: RAS, UCAS, LCAS, WE, OE Data Input/Output Capacitance: I/O0-I/O15 Max. Unit 5 7 7 pF pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25C, f = 1 MHz. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 5 ISSI IS41LV16400 (R) ELECTRICAL CHARACTERISTICS(1) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter IIL Input Leakage Current IIO Output Leakage Current VOH VOL I CC1 Output High Voltage Level Output Low Voltage Level Standby Current: TTL I CC2 I CC3 Standby Current: CMOS Operating Current: Random Read/Write(2,3,4) Average Power Supply Current Operating Current: EDO Page Mode(2,3,4) Average Power Supply Current Refresh Current: RAS-Only(2,3) Average Power Supply Current Refresh Current: CBR(2,3,5) Average Power Supply Current I CC4 I CC5 I CC6 Test Condition Speed Min. Max. Unit -5 5 A -5 5 A -- 0.4 1 2 2 0.5 160 145 V V mA mA mA mA mA Any input 0V VIN Vcc Other inputs not under test = 0V Output is disabled (Hi-Z) 0V VOUT Vcc IOH = -2.0 mA IOL = 2.0 mA RAS, LCAS, UCAS VIH Commerical Extended Industrial RAS, LCAS, UCAS VCC - 0.2V RAS, LCAS, UCAS, Address Cycling, tRC = tRC (min.) -50 -60 2.4 -- -- -- -- -- -- -- RAS = VIL, LCAS, UCAS, Cycling tPC = tPC (min.) -50 -60 -- -- 90 80 mA RAS Cycling, LCAS, UCAS VIH tRC = tRC (min.) -50 -60 -- -- 160 145 mA RAS, LCAS, UCAS Cycling tRC = tRC (min.) -50 -60 -- -- 160 145 mA Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each EDO page cycle. 5. Enables on-chip refresh and address counters. 319 AC TEST CONDITIONS Output load: One TTL Load and 50 pF Input timing reference levels: VIH = 2.0V, VIL = 0.8V Output timing reference levels: VOH = 2.0V, VOL = 0.8V 3.3V OUTPUT 50 pF Including jig and scope 6 353 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 Symbol Parameter t RC t RAC t CAC tAA tRAS t RP tCAS t CP t CSH t RCD tASR t RAH tASC t CAH t AR Random READ or WRITE Cycle Time Access Time from RAS(6, 7) Access Time from CAS(6, 8, 15) Access Time from Column-Address(6) RAS Pulse Width RAS Precharge Time CAS Pulse Width(26) CAS Precharge Time(9, 25) CAS Hold Time (21) RAS to CAS Delay Time(10, 20) Row-Address Setup Time Row-Address Hold Time Column-Address Setup Time(20) Column-Address Hold Time(20) Column-Address Hold Time (referenced to RAS) RAS to Column-Address Delay Time(11) Column-Address to RAS Lead Time RAS to CAS Precharge Time RAS Hold Time(27) RAS Hold Time from CAS Precharge CAS to Output in Low-Z(15, 29) CAS to RAS Precharge Time(21) Output Disable Time(19, 28, 29) Output Enable Time(15, 16) Output Enable Data Delay (Write) OE HIGH Hold Time from CAS HIGH OE HIGH Pulse Width OE LOW to CAS HIGH Setup Time Read Command Setup Time(17, 20) Read Command Hold Time (referenced to RAS)(12) Read Command Hold Time (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) Write Command Hold Time (referenced to RAS)(17) Write Command Pulse Width(17) t RAD t RAL t RPC t RSH t RHCP tCLZ t CRP tOD tOE tOED tOEHC tOEP tOES t RCS t RRH t RCH t WCH t WCR tWP Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 -60 Min. Max. Min. Max. Units 84 -- -- -- 50 30 8 9 38 12 0 8 0 8 30 -- 50 13 25 10K -- 10K -- -- 37 -- -- -- -- -- 104 -- -- -- 60 40 10 9 40 14 0 10 0 10 40 -- 60 15 30 10K -- 10K -- -- 45 -- -- -- -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 10 25 5 8 37 0 5 3 -- 20 5 10 5 0 0 25 -- -- -- -- -- -- 15 13 -- -- -- -- -- -- 12 30 5 10 37 0 5 3 -- 20 5 10 5 0 0 30 -- -- -- -- -- -- 15 15 -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 0 -- 0 -- ns 8 40 -- -- 10 50 -- -- ns ns 8 -- 10 -- ns 7 ISSI IS41LV16400 (R) AC CHARACTERISTICS (Continued)(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter tWPZ t RWL t CWL tWCS t DHR t ACH WE Pulse Widths to Disable Outputs Write Command to RAS Lead Time(17) Write Command to CAS Lead Time(17, 21) Write Command Setup Time(14, 17, 20) Data-in Hold Time (referenced to RAS) Column-Address Setup Time to CAS Precharge during WRITE Cycle OE Hold Time from WE during READ-MODIFY-WRITE cycle(18) Data-In Setup Time(15, 22) Data-In Hold Time(15, 22) READ-MODIFY-WRITE Cycle Time RAS to WE Delay Time during READ-MODIFY-WRITE Cycle(14) CAS to WE Delay Time(14, 20) Column-Address to WE Delay Time(14) EDO Page Mode READ or WRITE Cycle Time(24) RAS Pulse Width in EDO Page Mode Access Time from CAS Precharge(15) EDO Page Mode READ-WRITE Cycle Time(24) Data Output Hold after CAS LOW Output Buffer Turn-Off Delay from CAS or RAS(13,15,19, 29) Output Disable Delay from WE Last CAS going LOW to First CAS returning HIGH(23) CAS Setup Time (CBR REFRESH)(30, 20) CAS Hold Time (CBR REFRESH)(30, 21) OE Setup Time prior to RAS during HIDDEN REFRESH Cycle Refresh Period (4,096 Cycles) Transition Time (Rise or Fall)(2, 3) tOEH t DS t DH t RWC t RWD t CWD tAWD t PC t RASP t CPA t PRWC t COH tOFF tWHZ t CLCH t CSR t CHR t ORD tREF tT 8 -50 Min. Max. -60 Min. Max. Units 10 13 8 0 39 15 -- -- -- -- -- -- 10 15 10 0 39 15 -- -- -- -- -- -- ns ns ns ns ns ns 8 -- 10 -- ns 0 8 108 64 -- -- -- -- 0 10 133 77 -- -- -- -- ns ns ns ns 26 39 20 -- -- -- 32 47 25 -- -- -- ns ns ns 50 -- 56 100K 30 -- 60 -- 68 100K 35 -- ns ns ns 5 1.6 -- 12 5 1.6 -- 15 ns ns 3 10 10 -- 3 10 10 -- ns ns 5 8 0 -- -- -- 5 10 0 -- -- -- ns ns ns -- 1 64 50 -- 1 64 50 ms ns Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 IS41LV16400 ISSI (R) Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between VIH and VIL (or between VIL and VIH) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 4. If CAS and RAS = VIH, data output is High-Z. 5. If CAS = VIL, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that tRCD tRCD (MAX). If tRCD is greater than the maximum recommended value shown in this table, tRAC will increase by the amount that tRCD exceeds the value shown. 8. Assumes that tRCD tRCD (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tCP. 10. Operation with the tRCD (MAX) limit ensures that tRAC (MAX) can be met. tRCD (MAX) is specified as a reference point only; if tRCD is greater than the specified tRCD (MAX) limit, access time is controlled exclusively by tCAC. 11. Operation within the tRAD (MAX) limit ensures that tRCD (MAX) can be met. tRAD (MAX) is specified as a reference point only; if tRAD is greater than the specified tRAD (MAX) limit, access time is controlled exclusively by tAA. 12. Either tRCH or tRRH must be satisfied for a READ cycle. 13. tOFF (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to VOH or VOL. 14. tWCS, tRWD, tAWD and tCWD are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If tWCS tWCS (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If tRWD tRWD (MIN), tAWD tAWD (MIN) and tCWD tCWD (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to VIH) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after tOEH is met. 19. The I/Os are in open during READ cycles once tOD or tOFF occur. 20. The first CAS edge to transition LOW. 21. The last CAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling CAS edge to first rising CAS edge. 24. Last rising CAS edge to next cycle's last rising CAS edge. 25. Last rising CAS edge to first falling CAS edge. 26. Each CAS must meet minimum pulse width. 27. Last CAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 9 ISSI IS41LV16400 (R) READ CYCLE tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD tRRH UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tRAL tCAH tASC Row Column Row tRCS tRCH WE tAA tRAC tCAC tCLC I/O tOFF(1) Open Open Valid Data tOE tOD OE tOES Undefined Don't Care Note: 1. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 10 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) EARLY WRITE CYCLE (OE = DON'T CARE) tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tRAH tASR ADDRESS tRAL tCAH tACH tASC Row Column Row tCWL tRWL tWCR tWCS tWCH tWP WE tDHR tDS I/O tDH Valid Data Don't Care Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 11 ISSI IS41LV16400 (R) READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) tRWC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tASR tRAH tRAL tCAH tASC tACH ADDRESS Row Column Row tRWD tCWL tRWL tCWD tRCS tAWD tWP WE tAA tRAC tCAC tCLZ I/O tDS Open Valid DOUT tOE tDH Valid DIN Open tOD tOEH OE Undefined Don't Care 12 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) EDO-PAGE-MODE READ CYCLE tRASP tRP RAS tCSH tCRP tPC(1) tCAS, tCLCH tRCD tCAS, tCLCH tCP tCP tRSH tCAS, tCLCH tCP UCAS/LCAS tAR tRAD tASR ADDRESS tASC tCAH tASC Row Column tRAL tCAH tCAH tASC Column Column Row tRAH tRRH tRCS tRCH WE tAA tRAC tCAC tCLZ I/O Open tAA tCPA tCAC tCOH Valid Data tOE tOES tAA tCPA tCAC tCLZ tOFF Valid Data tOEHC Valid Data Open tOE tOD tOES tOD OE tOEP Undefined Don't Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 13 ISSI IS41LV16400 (R) EDO-PAGE-MODE EARLY-WRITE CYCLE tRASP tRP tRHCP RAS tCSH tCRP tPC tCAS, tCLCH tRCD tCAS, tCLCH tCP tCP tRSH tCAS, tCLCH tCP UCAS/LCAS tAR tACH tCAH tASC tRAD tASR ADDRESS tASC Row Column tRAH tACH tRAL tCAH tACH tCAH tASC Column tCWL tWCS Column tCWL tWCS tWCH tCWL tWCS tWCH tWCH tWP tWP Row tWP WE tWCR tDHR tRWL tDS tDS tDH I/O Valid Data tDS tDH Valid Data tDH Valid Data OE Don't Care 14 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) EDO-PAGE-MODE READ-WRITE CYCLE (LATE WRITE and READ-MODIFY WRITE Cycles) tRASP tRP RAS tCSH tCRP tCAS, tCLCH tRCD tCP tPC / tPRWC(1) tCAS, tCLCH tRSH tCAS, tCLCH tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC tCAH Row tASC tCAH Column tRWD tRCS tRAL tCAH tASC Column tCWL tWP Column tRWL tCWL tWP tCWL tWP tAWD tCWD Row tAWD tCWD tAWD tCWD WE tAA tAA tCPA tDH tDS tRAC tCAC tCLZ I/O Open tAA tCPA tDH tDS tCAC tCLZ DOUT DIN tOE tCAC tCLZ DOUT tOD DIN DOUT tOD tOE tDH tDS Open DIN tOD tOE tOEH OE Undefined Don't Care Note: 1. tPC can be measured from falling edge of CAS to falling edge of CAS, or from rising edge of CAS to rising edge of CAS. Both measurements must meet the tPC specifications. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 15 ISSI IS41LV16400 (R) EDO-PAGE-MODE READ-EARLY-WRITE CYCLE (Psuedo READ-MODIFY WRITE) tRASP tRP RAS tCSH tPC tPC tCRP tCAS tRCD tCAS tCP tRSH tCAS tCP tCP UCAS/LCAS tASR tRAH ADDRESS tAR tRAD tASC Row tCAH tASC tCAH Column (A) tASC Column (B) tRCS tACH tRAL tCAH Column (N) Row tRCH tWCS tWCH WE tAA tRAC tCAC I/O Open tCPA tCAC tCOH Valid Data (A) tAA tWHZ tDS Valid Data (B) tDH DIN Open tOE OE Don't Care 16 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) AC WAVEFORMS READ CYCLE (With WE-Controlled Disable) RAS tCSH tCRP tRCD tCP tCAS UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tCAH tASC Row tASC Column Column tRCS tRCH tRCS WE tAA tRAC tCAC tCLZ Open I/O tWHZ tCLZ Valid Data Open tOE tOD OE Undefined Don't Care RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) tRC tRAS tRP RAS tCRP tRPC UCAS/LCAS tASR ADDRESS tRAH Row I/O Row Open Don't Care Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 17 ISSI IS41LV16400 (R) CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) tRP tRAS tRP tRAS RAS tCHR tRPC tCP tCHR tRPC tCSR tCSR UCAS/LCAS Open I/O HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) tRAS tRP tRAS RAS tCRP tRCD tRSH tCHR UCAS/LCAS tAR tRAD tRAH tASC tASR ADDRESS Row tRAL tCAH Column tAA tRAC tOFF(2) tCAC tCLZ I/O Open Valid Data tOE Open tOD tORD OE Undefined Don't Care Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. 18 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 ISSI IS41LV16400 (R) ORDERING INFORMATION: 5V Commercial Range: 0C to 70C Speed (ns) 50 60 Order Part No. Package IS41LV16400-50T IS41LV16400-60T 400-mil TSOP (Type II) 400-mil TSOP (Type II) ORDERING INFORMATION: 3.3V Extended Temperature Range: -30C to 85C Speed (ns) 50 60 Order Part No. Package IS41LV16400-50TE IS41LV16400-60TE 400-mil TSOP (Type II) 400-mil TSOP (Type II) ORDERING INFORMATION: 3.3V Industrial Temperature Range: -40C to 85C Speed (ns) 50 60 Order Part No. Package IS41LV16400-50TI IS41LV16400-60TI 400-mil TSOP (Type II) 400-mil TSOP (Type II) ISSI (R) Integrated Silicon Solution, Inc. 2231 Lawson Lane Santa Clara, CA 95054 Tel: 1-800-379-4774 Fax: (408) 588-0806 E-mail: sales@issi.com www.issi.com Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. A 11/18/99 19