ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Description Features The ICS1493A-19 is a low cost frequency generator used for automotive application. Using patented Phase-Locked-Loop (PLL) techniques, the device uses a 19.35 MHz fundamental crystal source to produce seven clock outputs and one reference clock output. The output clocks are at 12.288 MHz, 14.7456 MHz, 22.5792 MHz, 48 MHz, 66.60 MHz, and 33.30 MHz with a 19.35 MHz reference clock output. The 66.60 MHz and 33.30 MHz clocks have a spread select option. Operating voltage of the ICS1493A-19 is 3.3 V. * * * * * Packaged in 28-pin TSSOP (4.4mm body) Low power CMOS technology Input crystal frequency of 19.35 MHz 3.3 V operating voltage Seven output clocks: 12.288 /33.30 MHz, 14.7456 MHz, 22.5792 MHz, 48 MHz, 66.60 MHz (3 copies) * One reference clock output at 19.35 MHz * Spread select option on the 66.60 MHz clock (3 copies) and 33.30 MHz clock outputs ICS makes many frequency generators. Contact us for all of your clocking needs. * Output enable pin stops clocks low (tri-state with weak pull-down resistors) * Zero ppm synthesis error for 48 MHz, 19.35 MHz clocks; 0.5 ppm error for 12.288 MHz, 14.7456 MHz, 22.5792 MHz clocks; 1 ppm error for 66.60 MHz and 33.30 MHz clocks. * Industrial temperature range (-40C to +85C) Block Diagram VDD 8 3 PLLA with Spread Spectrum SSEN 66.60M 12.288M/ 33.30M PLLB 14.7456M X1 19.35 MHz Crystal 48M PLLD 22.5792M Crystal Oscillator 19.35M X2 7 External tuning capacitors required MDS 1493A-19 C PLLC FSEL GND OE 1 Integrated Device Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Pin Assignment Spread Enable Table 1 X1 1 28 X2 GNDX 2 27 VDDX SSEN 66.60/33.30 MHz Clock CLK19 3 26 FSEL 0 No spread (default) GND14&19 4 25 OE 1 -1.0% VDD14&19 5 24 SSEN CLK14 6 23 VDDPLL VDD48 7 22 GNDPLL GND48 8 21 CLK66 CLK48 9 20 VDD66 VDD22 10 19 CLK33 GND22 11 18 VDD33 CLK22 12 17 GND33 VDD66 13 16 GND66 CLK66 14 15 CLK66 Output Enable Function Table 2 OE Output Status 0 Stopped low 1 Running (default) Frequency Select Table 3 FSEL Clock Selected (MHz) 0 12.288 1 33.30 (default) 28-pin (173 mil) TSSOP Pin Descriptions Pin Number Pin Name Pin Type 1 X1 Input Crystal connection. Connect to a 19.35 MHz fundamental crystal. 2 GNDX Power Crystal oscillator circuit ground. 3 CLK19 Output 19.35 MHz reference clock output. Internal weak pull-down resistor. 4 GND14&19 Power Connect to 14.7456 MHz and 19.35 MHz clock output ground. 5 VDD14&19 Power Output driver power for 14.7456 MHz clock output. 6 CLK14 Output 14.7456 MHz clock output. Internal weak pull-down resistor. 7 VDD48 Power Output driver power for 48 MHz clock output. 8 GND48 Power Connect to 48 MHz clock output ground. 9 CLK48 Output 48 MHz clock output. Internal weak pull-down resistor. 10 VDD22 Power Output driver power for 22.5792 MHz clock output. 11 GND22 Power Connect to 22.5792 MHz clock output circuit ground. 12 CLK22 Output 22.5792 MHz clock output. Internal weak pull-down resistor. 13 VDD66 Power Output driver power for 66.60 MHz clock output. 14 CLK66 Output 66.60 MHz clock output. Internal weak pull-down resistor. 15 CLK66 Output 66.60 MHz clock output. Internal weak pull-down resistor. MDS 1493A-19 C Pin Description 2 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Pin Number Pin Name Pin Type 16 GND66 Power Connect to 66.60 MHz clock output circuit ground. 17 GND33 Power Connect to 33.30 MHz clock output circuit ground. 18 VDD33 Power Output driver power for 33.30 MHz clock output. 19 CLK33 /12.288 Output 33.30 /12.288 MHz clock output. Internal weak pull-down resistor. 20 VDD66 Power Output driver power for 66.60 MHz clock output. 21 CLK66 Output 66.60 MHz clock output. Internal weak pull-down resistor. 22 GNDPLL Power Connect to PLL circuit ground. 23 VDDPLL Power VDD for PLL circuits Connect to 3.3 V. 24 SSEN Input Spread enable pin for 66.60 MHz clock. See table 1 above. Internal pull-down resistor. 25 OE Input Enables output when =1 and disables (pulled low) when =0. See table above 2. Internal pull-up resistor. 26 FSEL Input Frequency select pin, internal pull-up. See Table 3. 27 VDDX Power VDD for crystal oscillator circuit. Connect to 3.3.V. 28 X2 Input Crystal connection. Connect to a 19.35 MHz fundamental crystal. MDS 1493A-19 C Pin Description 3 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION External Components Decoupling Capacitor PCB Layout Recommendations As with any high-performance mixed-signal IC, the ICS1493A-19 must be isolated from system power supply noise to perform optimally. Observe the following guidelines for optimum device performance and lowest output phase noise: A decoupling capacitor of 0.01F must be connected between each VDD and the PCB ground plane. Series Termination Resistor Clock output traces should use series termination. To series terminate a 50 trace (a commonly used trace impedance), place a 33 resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20. Crystal Load Capacitors The device crystal connections should include pads for capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. The value (in pF) of these crystal caps should equal (CL - 6 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 20 pF [(16-6) x 2 = 20 pF]. MDS 1493A-19 C 1) The 0.01F decoupling capacitors should be mounted on the component side of the board as close to the VDD pins as possible. No vias should be used between the decoupling capacitors and VDD pins. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. 2) The external crystal should be mounted just next to the device with short traces. The X1 and X2 traces should not be routed next to each other with minimum spaces. Instead, they should be separated and away from other traces. 3) Place the 33 series termination resistor (if needed) close to the clock output to minimize EMI. 4) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS1493A-19. This includes signal traces just underneath the device, or on layers adjacent to the ground plane layer used by the device. 4 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS1493A-19. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD -0.5 V to 7 V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature -40 to +85 C Storage Temperature -65 to +150 C Junction Temperature 125 C Soldering Temperature 260 C Recommended Operation Conditions Parameter Min. Ambient Operating Temperature -40 Power Supply Voltage (measured in respect to GND) +3.0 Typ. +3.3 Max. Units +85 C +3.6 V DC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 10%, Ambient Temperature -40 to +85 C Parameter Symbol Conditions Min. Typ. Max. Units 3.0 3.3 3.6 V Operating Voltage VDD Supply Current IDD Input High Voltage VIH Input Low Voltage VIL Output High Voltage VOH IOH = -4 mA VDD-0.4 V Output High Voltage VOH IOH = -12 mA 2.4 V Output Low Voltage VOL IOL = 12 mA Short Circuit Current IOS Clock outputs,15 and 21 80 mA Short Circuit Current IOS Clock outputs 3, 6, 9, 12, 14, and 19 70 mA Input Capacitance CIN Input 5 pF 20 200 k Nominal Output Impedance ZOUT Internal Pull-up Resistor RPU MDS 1493A-19 C No load 80 mA 2 V 0.8 0.4 FSEL, OE pins 5 I n t e gra te d D ev i ce Technology, Inc. V V Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Parameter Symbol Internal Pull-down Resistor RPd Conditions Min. Typ. Max. Units All clock outputs except SSEN pin 200 k SSEN pin 100 k AC Electrical Characteristics Unless stated otherwise, VDD = 3.3 V 10%, Ambient Temperature -40 to +85 C Parameter Symbol Conditions Min. Typ. Max. Units Input Frequency fIN Output Rise Time tOR 20% to 80%, CL=12 pF 1.1 1.5 ns Output Fall Time tOF 80% to 20%, CL=12 pF 1.1 1.5 ns Output Clock Duty Cycle 19.35 MHz at VDD/2, CL=12 pF 45 50 55 % at VDD/2, Pin 3, CL=12 pF 40 50 60 % 175 ps Output-to-Output Skew Pins 14, 15, and 21 only Output Enable Time OE going high to output valid 1 ms Output Disable Time OE going low to output Invalid 1 ms Power-up Time Power on to output valid 20 ms Spread Modulation Spread rate 32 kHz Jitter, Cycle-to-cycle All clocks except reference clock 19.35 MHz 300 ps Jitter, Cycle-to-cycle Reference clock 19.35 MHz 500 ps Jitter, Peak-to-peak Peak-to-peak, all clocks except reference clock 19.35 MHz 150 ps Jitter, Peak-to-peak Peak-to-peak, reference clock 19.35 MHz 250 ps Output Frequency Synthesis Error All clocks Transition Time tTR 10 Measured from a change of FSEL until clock stable within 1% 1 ppm ms Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case MDS 1493A-19 C Symbol Conditions Min. Typ. Max. Units JA Still air 83 C/W JA 1 m/s air flow 75 C/W JA 3 m/s air flow 61 C/W 60 C/W JC 6 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Marking Diagram 28 15 1493AGI-19LF ###### YYWW 14 1 Notes: 1. ###### is the lot number. 2. YYWW is the last two digits of the year and week that the part was assembled. 3. "LF" denotes Pb (lead) free package. 4. Bottom marking: (origin) Origin = country of origin if not USA. MDS 1493A-19 C 7 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m ICS1493A-19 CLOCK GENERATOR FOR AUTOMOTIVE APPLICATION Package Outline and Package Dimensions (28-pin TSSOP, 4.4mm body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 28 Symbol E1 INDEX AREA A A1 A2 b C D E E1 e L aaa E 1 2 D Max Min -1.20 0.05 0.15 0.80 1.05 0.19 0.30 0.09 0.20 9.60 9.80 6.40 BASIC 4.30 4.50 0.65 Basic 0.45 0.75 0 8 -0.10 Max -0.047 0.002 0.006 0.032 0.041 0.007 0.012 0.0035 0.008 0.378 0.386 0.252 BASIC 0.169 0.177 0.0256 Basic 0.018 0.030 0 8 -0.004 *For reference only. Controlling dimensions in mm. A A2 Min Inches* A1 c - Ce SEATING PLANE b L aaa C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature ICS1493AGI-19LF ICS1493AGI-19LFT see page 7 Tubes Tape and Reel 28-pin TSSOP 28-pin TSSOP -40 to +85 C -40 to +85 C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. MDS 1493A-19 C 8 I n t e gra te d D ev i ce Technology, Inc. Revision 051310 w w w. i d t . c o m