DETAIL SPECIFICATION SHEET
CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING),
PLUG, (THREADED COUPLING, SELF-LOCKING, CRIMP PIN CONTACT),
(SERIES III, CLASSES A, G, K, M, R, T, W AND Z)
This specificat ion i s approved for use by al l Departments
and Agencies of the Department of Defense.
The requirement s for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Dimensions and configurat i ons.
AMSC N/A FSC 5935
INCH-POUND
MIL-DTL-83723/96G
1 October 2009
SUPERSEDING
MIL-DTL-83723/96F
15 September 2006
MIL-DTL-83723/96G
2
FIGURE 1. Dimensions and configurat i ons - Continued.
MIL-DTL-83723/96G
3
Shell
size A
Thread
UNEF-2B
B C
H
min
J K W
max
8 .5625-24 .290 (7.37)
.025
(.64)
.294 (7.47)
.405
(10.29)
.396
(10.06)
.575
(14.61) .832
(21.13)
10 .6875-24 .388 (9.86)
.031
(.79)
.428
(10.87) .526
(13.36)
.517
(13.13)
.707
(17.96) .959
(24.36)
12 .875-20 .558
(14.17) .598
(15.19) .696
(17.68)
.687
(17.45)
.895
(22.73) 1.097
(27.86)
14 .9375-20 .627
(15.93) .667
(16.94) .765
(19.43)
.756
(19.20)
.957
(24.31) 1.236
(31.39)
16 1.0625-18 .772
(19.61) .794
(20.17) .892
(22.66)
.883
(22.43)
1.084
(27.53) 1.360
(34.54)
18 1.1875-18 .860
(21.84) .900
(22.86) .998
(25.35)
.989
(25.12)
1.209
(30.71) 1.473
(37.41)
20 1.3125-18 .985
(25.02) 1.025
(26.04) 1.123
(28.52)
1.114
(28.30)
1.334
(33.88) 1.586
(40.28)
22 1.4375-18 1.110
(28.19) 1.150
(29.21) 1.248
(31.70)
1.239
(31.47)
1.459
(37.06) 1.703
(43.26)
24 1.5625-18 1.235
(31.37) 1.275
(32.39) 1.373
(34.87)
1.364
(34.65)
1.584
(40.23) 1.846
(46.89)
FIGURE 1. Dimensions and configurat i ons - Continued.
MIL-DTL-83723/96G
4
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005 0.13 .215 5.46 .687 17.45 1.114 28.29
.007 0.18 .221 5.46 .6875 17.46 1.123 28.52
.008 0.20 .235 5.97 .696 17.68 1.150 29.21
.015 0.38 .243 6.17 .707 17.96 1.180 29.97
.018 0.46 .260 6.60 .756 19.20 1.1875 30.16
.020 0.51 .290 7.37 .765 19.43 1.209 30.71
.022 0.56 .294 7.47 .772 19.61 1.235 31.37
.031 0.79 .330 8.38 .794 20.17 1.236 31.39
.032 0.81 .388 9.86 .832 21.13 1.239 31.47
.042 1.07 .396 10.05 .860 21.84 1.248 31.70
.046 1.17 .400 10.16 .875 22.23 1.275 32.39
.048 1.22 .405 10.29 .883 22.43 1.334 33.88
.065 1.65 .428 10.87 .892 22.66 1.360 34.54
.068 1.73 .433 11.00 .895 22.73 1.364 34.65
.069 1.75 .479 12.17 .900 22.86 1.373 34.87
.084 2.13 .500 12.70 .9375 23.81 1.4375 36.51
.090 2.29 .510 12.95 .957 24.31 1.459 37.06
.097 2.46 .517 13.13 .959 24.36 1.5625 39.69
.101 2.57 .526 13.36 .985 25.02 1.584 40.23
.106 2.69 .558 14.71 .989 25.12 1.586 40.28
.112 2.84 .5625 14.29 .998 25.35 1.703 43.26
.125 3.18 .575 14.60 1.025 26.03 1.846 46.89
.138 3.51 .598 15.19 1.0625 26.99
.144 3.66 .627 15.93 1.084 27.53
.198 5.03 .667 16.94 1.097 27.86
.204 5.18 .675 17.15 1.110 28.19
NOTES:
1. Dimensions are i n i nches.
2. Metric equivalents are given f or i nformation only.
3. Unless otherwis e specified, tolerances are ± .005 (0.13 mm ) for three place dec i m al s and
± .01 (0.25 mm) f or two place decimals and ± 1° for all angle s.
4. The dimensio ns showing the relationship between the coupling ring and connector shell apply only
when the coupli ng ring is in the fully forward position.
5. Rear accesso ry i nterchangeability di m ensions shall be in acc ordance with MIL-DTL-83723.
6. Shell size 8 will not mate with MIL-DTL-26500 connectors.
7. The centerline of indicated projection must be lo cat ed on vertical centerline ± 2°.
8. See table I for cont act cavities req ui ring this dimension.
FIGURE 1. Dimensions and configurat i ons - Continued.
MIL-DTL-83723/96G
5
REQUIREMENTS:
Dimensions and configurations: See f i gure 1.
This connector mat es with MIL-DTL-83723/82 and MIL-DTL-83723/84.
Insert arrangements and polarizing positions: See MIL-STD-1554 and table I.
TABLE I. Insert arrangements re quiring reduced diameters for raised seal
barriers on contact cav ities.
Shell
size Insert
arrangements Contact
cavities
8 03 1, 2, 3
10 06 1, 2, 3, 4, 5, 6
Connector accessories: See SAE-AS85049.
Part or Identif ying Number (PIN) example:
M83723/ 96 K 22 55 N
Military designation
Specification sheet number
Class
Shell size
Insert arrangement
Polarizing position
Changes from prev i ous issue. Marginal not ations are not used in this revision to identify changes with
respect to the prev ious issue, due to t he ext ent of the changes.
Referenced docum ents. In addition t o M IL-DTL-83723, this document references the following:
MIL-STD-1554
MIL-DTL-26500
MIL-DTL-83723/82
MIL-DTL-83723/84
SAE-AS85049
MIL-DTL-83723/96G
6
CONCLUDING MATERIAL
Custodians: P reparing activity:
Army - CR DLA - CC
Navy - AS
Air Force - 85
DLA - CC
Review activities: (Project 5935-2008-172)
Army - AR, MI
Navy - EC
Air Force - 19, 99
NOTE: The activ i ties listed above were interested in this document as of the date of this document .
Since organizati ons and responsibilit ies can change, y ou should verify the currency of the informati on
above using the A S SIST Online database at http://assist.daps.dla.mil.
