FEATURES
NEC's ¼ W SINGLE CONTROL
L, S-BAND SPDT SWITCH
DESCRIPTION
UPG2012TK
NEC's UPG2012TK is a single control GaAs MMIC for
L, S-band SPDT (Single Pole Double Throw) switch for
mobile phone and L, S-band applications.
This device can operate frequency from 0.5 GHz to 2.5
GHz, with low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold pack-
age suitable for high-density surface mounting.
APPLICATIONS
• L, S-band digital cellular or cordless handsets
• BluetoothTM , W-LAN and WLL
• Short Range Wireless
California Eastern Laboratories
ORDERING INFORMATION
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order: UPG2012TK
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
• SUPPLY VOLTAGE:
VDD = 2.7 to 3.0 V (2.8 V TYP.)
• SINGLE SWITCH CONTROL VOLTAGE:
Vcont (H) = 2.7 to 3.0 V (2.8 V TYP.)
Vcont (L) = −0.2 to +0.2 V (0 V TYP.)
• LOW INSERTION LOSS:
LINS1 = 0.27 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
LINS2 = 0.30 dB TYP. @ f = 2.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
LINS3 = 0.30 dB TYP. @ f = 2.5 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
(Reference value)
• HIGH ISOLATION:
ISL1 = 30 dB TYP. @ f = 0.5 to 2.0 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
ISL2 = 30 dB TYP. @ f = 2.5 GHz, VDD = 2.8 V, Vcont = 2.8 V/0 V
(Reference value)
• HIGH-DENSITY SURFACE MOUNTING:
6-pin lead-less minimold package
Part Number Package Marking Supplying Form
UPG2012TK-E2-A 6-pin lead-less minimold
(1511)
G3H • Embossed tape 8 mm wide
• Pin 1, 6 face the perforation side of the tape
• Qty 5 kpcs/reel
UPG2012TK
ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified)
RECOMMENDED OPERATING RANGE (TA = 25°C)
PIN CONNECTIONS
(Top View)
1
2
3 4
5
6
G3H
(Top View)
1
2
3 4
5
6
(Bottom View)
6
5
4 3
2
1
Pin No. Pin Name
1 OUTPUT1
2 GND
3 OUTPUT2
4 Vcont
5 INPUT
6 VDD
TRUTH TABLE
Vcont INPUT−OUTPUT1 INPUT−OUTPUT2
Low OFF ON
High ON OFF
Parameter Symbol Ratings Unit
Supply Voltage VDD +6.0 V
Switch Control Voltage Vcont +6.0 V
Input Power Pin +26 dBm
Power Dissipation PD150 Note mW
Operating Ambient Temperature TA−45 to +85 °C
Storage Temperature Tstg −55 to +150 °C
Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB, TA = +85°C
Parameter Symbol MIN. TYP. MAX. Unit
Supply Voltage VDD 2.7 2.8 3.0 V
Switch Control Voltage (H) Vcont(H) 2.7 2.8 3.0 V
Switch Control Voltage (L) Vcont(L) −0.2 0 0.2 V
ELECTRICAL CHARACTERISTICS
(TA = +25°C, VDD = 2.8 V, Vcont = 2.8 V/0 V, DC blocking capacitors = 56 pF, unless otherwise specified)
Note Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of linear
range.
UPG2012TK UPG2012TK
Caution It is necessary to use DC blocking capacitors with the device.
The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching
speed and the condition with the actual board of the system. The range of recommended DC blocking capacitor value is
less than 100 pF.
Parameter Symbol Test Conditions MIN. TYP. MAX. Unit
Insertion Loss1 LINS1 f = 0.5 to 1.0 GHz −0.27 0.50 dB
Insertion Loss2 LINS2 f = 2.0 GHz −0.30 0.50 dB
Isolation1 ISL1 f = 0.5 to 2.0 GHz 24 30 −dB
Input Return Loss RLin f = 0.5 to 2.5 GHz 15 20 −dB
Output Return Loss RLout f = 0.5 to 2.5 GHz 15 20 −dB
0.1 dB Gain Compression
Input Power Note Pin(0.1 dB) f = 2.0 GHz +17.5 +20.5 −dBm
Supply Current IDD −50 100 μA
Switching Control Current Icont −4 20 μA
STANDARD CHARACTERISTICS FOR REFERENCE
(TA = +25°C, VDD = 2.8 V,Vcont = 2.8 V/0 V, DC blocking capacitors = 56 pF, unless otherwise specified)
Parameter Symbol Test Conditions MIN. TYP. MAX. Unit
Insertion Loss3 LINS3 f = 2.5 GHz −0.30 −dB
Isolation2 ISL2 f = 2.5 GHz −30 −dB
1 dB Gain Compression
Input Power Note Pin(1 dB) f = 2.0 GHz −+24.0 −dBm
Switching Control Speed tSW −300 −ns
Note Pin (1dB) is the measured input power level when the insertion loss increases 1 dB more than that of linear
range.
UPG2012TK UPG2012TK
EVALUATION CIRCUIT
(VDD = 2.8 V, Vcont = 2.8 V/0 V, DC blocking capacitors = 56 pF)
VDD Vcont
OUTPUT1 OUTPUT2
INPUT
56 pF
56 pF56 pF
1 000 pF1 000 pF
456
321
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
UPG2012TK UPG2012TK
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
6pin L2MM SPDT SW
Vc1
Vc2
IN
OUT 1
OUT 2
C1
C1
C3
C5
C1
C2
C4
C1
C2
C2
Vcont
OUTPUT2
INPUT
OUTPUT1
VDD
G3H
USING THE NEC EVALUATION BOARD
Symbol Values
C1, C2, C3 56 pF
C4, C5 1 000 pF
UPG2012TK UPG2012TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511) (UNIT: mm)
Remark ( ): Reference value
0.48±0.050.48±0.05
UPG2012TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method Soldering Conditions Condition Symbol
Infrared Reflow Peak temperature (package surface temperature) : 260°C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220°C or higher : 60 seconds or less
Preheating time at 120 to 180°C : 120±30 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
VPS Peak temperature (package surface temperature) : 215°C or below
Time at temperature of 200°C or higher : 25 to 40 seconds
Preheating time at 120 to 150°C : 30 to 60 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
VP215
Wave Soldering Peak temperature (molten solder temperature) : 260°C or below
Time at peak temperature : 10 seconds or less
Preheating temperature (package surface temperature) : 120°C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating Peak temperature (pin temperature) : 350°C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
A Business Partner of NEC Compound Semiconductor Devices, Ltd.
08/30/2004
Caution Do not use different soldering methods together (except for partial heating).
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile:
408
988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A -AZ
Lead (Pb) < 1000 PPM Not Detected (*)
Mercury < 1000 PPM Not Detected
Cadmium < 100 PPM Not Detected
Hexavalent Chromium < 1000 PPM Not Detected
PBB < 1000 PPM Not Detected
PBDE < 1000 PPM Not Detected
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.