D WIMA MKP 2 Metallized Polypropylene (PP) Capacitors in PCM 5 mm Special Features Electrical Data High volume/capacitance ratio Self-healing Increased pulse duty from 250 VDC rated voltage Very low dissipation factor Negative capacitance change versus temperature Very low dielectric absorption According to RoHS 2002/95/EC Typical Applications For high frequency applications e.g. Sample and hold Timing Oscillating circuits High frequency coupling and decoupling Construction Dielectric: Polypropylene (PP) film Capacitor electrodes: Vacuum-deposited Internal construction: Capacitance range: 1000 pF to 0.33 mF (E12-values on request) Rated voltages: 63 VDC, 100 VDC, 250 VDC, 400 VDC, 630 VDC, 1000 VDC Capacitance tolerances: 20%, 10%, 5% Operating temperature range: -55+ C to +100+ C Test specifications: In accordance with IEC 60384-16 and EN 131 200 Climatic test category: 55/085/56 in accordance with IEC Insulation resistance at +20+ C: 3 x 104 M (mean value: 1 x 10 5 M) Measuring voltage: Ur= 63 V: U test = 50 V/1 min. Ur 100 V: U test = 100 V/1 min. Test voltage: 1.6 U r, 2 sec. Maximum pulse rise time: Capacitance pF/mF Plastic film Vacuum-deposited electrode Metal contact layer (schoopage) Terminating wire Dielectric absorption: 0.05 % Dissipation factors at +20+ C: tan d at f C0.1 mF 0.1 mF P C 0.33 mF 1 kHz 0.5 x 10-3 10 kHz 0.8 x 10-3 100 kHz 3.0 x 10-3 0.5 x 10-3 0.8 x 10-3 - Voltage derating: A voltage derating factor of 1.35 % per K must be applied from +85+ C for DC voltages and from +75+ C for AC voltages Reliability: Operational life 300 000 hours Failure rate 2 fit (0.5 x U r and 40+ C) max. pulse rise time V/ msec 63 VDC 100 VDC 250 VDC 400 VDC - - 100 100 100 100 - - 100 100 100 100 - - 250 250 250 250 300 300 300 300 - - 1000 ... 2200 3300 ... 6800 0.01 ... 0.022 0.033 ... 0.068 0.1 ... 0.22 0.33 630 VDC 1000 VDC 400 400 400 400 - - 500 500 500 - - - for pulses equal to the rated voltage Mechanical Tests Pull test on leads: 10 N in direction of leads according to IEC 60068-2-21 Vibration: 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 4000 bumps at 390 m/sec 2 in accordance with IEC 60068-2-29 Available taped and reeled. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. 11.10 Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire. Marking: Colour: Red. Marking: Black. Epoxy resin seal: Red Packing 36 D WIMA WIMA MKP FKP 42 Continuation General Data Capacitance W H 63 VDC/40 VAC* PCM** Part number L W H 100 VDC/63 VAC* PCM** Part number L 0.01 0.015 0.022 0.033 0.047 0.068 mF 3 7.5 3 7.5 3 7.5 3 7.5 3.5 8.5 4.5 9.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2C021001B00_ _ _ _ MKP2C021501B00_ _ _ _ MKP2C022201B00_ _ _ _ MKP2C023301B00_ _ _ _ MKP2C024701C00_ _ _ _ MKP2C026801E00_ _ _ _ 3 7.5 3 7.5 3 7.5 3 7.5 3.5 8.5 4.5 9.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2D021001B00_ _ _ _ MKP2D021501B00_ _ _ _ MKP2D022201B00_ _ _ _ MKP2D023301B00_ _ _ _ MKP2D024701C00_ _ _ _ MKP2D026801E00_ _ _ _ 0.1 0.15 0.22 0.33 mF 5 5.5 7.2 8.5 10 11.5 13 14 7.2 7.2 7.2 7.2 5 5 5 5 MKP2C031001F00_ _ _ _ MKP2C031501H00_ _ _ _ MKP2C032201K00_ _ _ _ MKP2C033301M00_ _ _ _ 5 5.5 7.2 8.5 10 11.5 13 14 7.2 7.2 7.2 7.2 5 5 5 5 MKP2D031001F00_ _ _ _ MKP2D031501H00_ _ _ _ MKP2D032201K00_ _ _ _ MKP2D033301M00_ _ _ _ W H L W H L Capacitance 250 VDC/160 VAC* PCM** Part number 1000 1500 2200 3300 4700 6800 pF 0.01 0.015 0.022 0.033 0.047 0.068 mF 3 7.5 3 7.5 3 7.5 3 7.5 3.5 8.5 4.5 9.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2F021001B00_ _ _ _ MKP2F021501B00_ _ _ _ MKP2F022201B00_ _ _ _ MKP2F023301B00_ _ _ _ MKP2F024701C00_ _ _ _ MKP2F026801E00_ _ _ _ 0.1 0.15 0.22 0.33 mF 5 7.2 7.2 8.5 7.2 7.2 7.2 7.2 5 5 5 5 MKP2F031001F00_ _ _ _ MKP2F031501K00_ _ _ _ MKP2F032201K00_ _ _ _ MKP2F033301M00_ _ _ _ 10 13 13 14 400 VDC/200 VAC* PCM** Part number 3 7.5 3 7.5 3 7.5 3 7.5 3 7.5 3 7.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2G011001B00_ _ _ _ MKP2G011501B00_ _ _ _ MKP2G012201B00_ _ _ _ MKP2G013301B00_ _ _ _ MKP2G014701B00_ _ _ _ MKP2G016801B00_ _ _ _ 3.5 8.5 3.5 8.5 4.5 9.5 5.5 11.5 7.2 13 7.2 13 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2G021001C00_ _ _ _ MKP2G021501C00_ _ _ _ MKP2G022201E00_ _ _ _ MKP2G023301H00_ _ _ _ MKP2G024701K00_ _ _ _ MKP2G026801K00_ _ _ _ * AC voltage: f 400 Hz; 1.4 x U rms + UDC U r ** PCM = Printed circuit module = lead spacing. Dims. in mm. W L H 6 d = 0.5 l -2 d Part number completion: Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Lead length: 6-2 = SD Taped version see page 127. 5 PCM at the lead exit points ( 0.5) Rights reserved to amend design data without prior notification. 11.10 Continuation page 38 37 D WIMA WIMA MKP FKP 42 Continuation General Data Capacitance W H L 630 VDC/250 VAC* PCM** Part number W H L 1000 VDC/250 VAC* PCM** Part number 1000 1500 2200 3300 4700 6800 pF 3 7.5 3 7.5 3 7.5 3 7.5 3 7.5 3.5 8.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2J011001B00_ _ _ _ MKP2J011501B00_ _ _ _ MKP2J012201B00_ _ _ _ MKP2J013301B00_ _ _ _ MKP2J014701B00_ _ _ _ MKP2J016801C00_ _ _ _ 3 7.5 3 7.5 3 7.5 3.5 8.5 4.5 9.5 5 10 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKP2O111001B00_ _ _ _ MKP2O111501B00_ _ _ _ MKP2O112201B00_ _ _ _ MKP2O113301C00_ _ _ _ MKP2O114701E00_ _ _ _ MKP2O116801F00_ _ _ _ 0.01 0.015 0.022 0.033 0.047 mF 4.5 9.5 5 10 5.5 11.5 7.2 13 8.5 14 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 MKP2J021001E00_ _ _ _ MKP2J021501F00_ _ _ _ MKP2J022201H00_ _ _ _ MKP2J023301K00_ _ _ _ MKP2J024701M00_ _ _ _ 7.2 7.2 5 MKP2O121001K00_ _ _ _ 13 * AC voltage: f 400 Hz; 1.4 x U rms + UDC U r ** PCM = Printed circuit module = lead spacing. Part number completion: Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Lead length: 6-2 = SD Dims. in mm. Taped version see page 127. Rights reserved to amend design data without prior notification. Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide). Urms V 5 250 2 22 00 01 0. 102 00 F Urms V 5 5 104 2 5 105 pF 5 f 106 Hz 2 00 7 04 F pF F 00 02 0. 5 F 105 5 pF 2 00 pF 10 00 47 1000 VDC 00 2 5 f 106 Hz 10 103 2 5 104 2 5 105 2 pF pF 5 f 106 Hz 11.10 2 pF F 104 8 22 102 2 06 5 00 47 0. 2 10 F 0. 400 VDC 2 250 2 22 1 01 103 2 0 0. 0. 102 10 103 pF Urms V 5 200 5 00 F 2 10 47 2 02 0. 630 VDC 10 F 7 04 0. 5 pF 38 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Wave soldering T A preheating of through-hole WIMA capacitors is allowed for temperatures T max P 100 C. In practice a preheating duration of t P 5 min. has been proven to be best. 260 240 220 200 180 160 140 120 100 80 60 40 20 Single wave soldering Soldering bath temperature: T P 260 C Immersion time: t P 5 sec Double wave soldering Soldering bath temperature: T P 260 C Immersion time: 2 x t P 3 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. 10 s [C] see detailenlargement 2s 3s t 30 60 90 120 150 180 210 240 [sec] Typical temperature/time graph for double wave soldering WIMA Quality and Environmental Philosophy ISO 9001:2008 Certification ISO 9001:2008 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2008 of our factories by the VDE inspectorate certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application of WPCS during production process: incoming material inspection metallization film inspection schoopage pre-healing lead attachment cast resin preparation/ encapsulation " 100% final inspection " AQL check All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. - - - - - Lead PCB CFC Hydrocarbon chloride Chromium 6+ - - - - - PBB/PBDE Arsenic Cadmium Mercury etc. RoHS Compliance According to the RoHS Directive 2002/95/EC certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. We merely use pure, recyclable materials for packing our components, such as: " " " " carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: " foamed polystyrene (Styropor(R)) " adhesive tapes made of plastic " metal clips Tape for lead-free WIMA capacitors DIN EN ISO 14001:2009 WIMA's environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2009 to optimize the production processes with regard to energy and resources. 11.10 " " " " " " " WIMA Environmental Policy 14 D Typical Dimensions for Taping Configuration Vh P P2 Diagram 1: PCM 2.5/5/7.5mm W W1 W0 H H1 W2 P1 D0 d P t F P0 H1 P P1 H P1 d d P0 P2 F Diagram 2: PCM 10/15 mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Designation Carrier tape width Dimensions for Radial Taping Symbol PCM 2.5 taping W P0 P2 F 18.0 p0.5 PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing Hold-down tape width W0 6.0 6.0 12.0 12.0 12.0 12.0 12.0 adhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tape Hole position W1 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 Hold-down tape position W2 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter D0 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 12.7 p1.0 12.7 p1.0 12.7 p1.0 25.4 p1.0 25.4 p1.0 38.1 p1.5 4.0 p0.2 3*8.1 p1.5 or 50.8 p1.5 Pitch of component P Feed hole pitch P0 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch Feed hole centre to lead P1 5.1 p0.5 3.85 p0.7 2.6 p0.7 7.7 p0.7 5.2 p0.7 7.8 p0.7 5.3 p0.7 Hole centre to component centre P2 6.35 p1.3 6.35 p1.3 6.35 p1.3 12.7 p1.3 12.7 p1.3 19.05 p1.3 19.05 p1.3 Feed hole centre to bottom H edge of the component 16.5 p0.3 18.5 p0.5 16.5 p0.3 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 Feed hole centre to top H edge of the component1 H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 24.5 to 31.5 H+Hcomponent < H1 25.0 to 31.5 H+Hcomponent < H1 26.0 to 37.0 H+Hcomponent < H1 30.0 to 43.0 H+Hcomponent < H1 35.0 to 45.0 Lead spacing at +0.8 F 2.5 p0.5 5.0 upper edge of carrier tape -0.2 7.5 p0.8 10.0 p0.8 15 p0.8 22.5 p0.8 27.5 p0.8 Lead diameter d 0.4 p0.05 Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 Total tape thickness t Package (see also page 128) REEL 0.5 p0.05 0.5 +0.06 p0.05 or 0.6 -0.05 0.5 +0,06 p0.05 or 0.6 -0.05 ROLL/AMMO P 360 max. 52 p2 P 30 p1B 58 p2 depending on comp. dimensions Unit 0.8 +0,08 -0.05 0.8 +0,08 -0.05 +0.08 0.8 -0.05 AMMO 52 p2 54 p2 max. P 500 max. B 58 p2 or REEL B 60 p2 REEL PP 360 30 p1 P 25 p1 66 p2 68 p2 depending on PCM and component dimensions see details page 130. Dims in mm. 11.10 Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer. * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible 127 D Packing Quantities for Bulk Capacitors and TPS* Size PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm 11.10 37.5 mm W 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 9 11 13 13 15 15 17 17 20 20 9 11 13 15 17 19 20 24 H 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 19 21 24 25 26 26 29 34.5 32 39.5 19 22 24 26 29 32 39.5 45.5 L 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 31.5 31.5 31.5 33 31.5 33 31.5 31.5 33 31.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 Codes 0B 0C 0D 0E 0F 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 1M 1N 2A 2B 2C 2D 2E 2F 2G 3A FA 3C 3D FB 3F 3G 3H 3I 4B FC 4C FD 4D FE 4F FF 4H 4J FG 4M 5A 5B 5D FH 5F FI 5G 5H 5I FJ 6A 6B 6D FK 6F FL 6G 6I FM 6J 7A 7B 7C 7D 7E 7F 7G 7H Rights reserved to amend design data without prior notification. Samples and pre-production needs on request. pcs. per packaging unit bulk Mini Standard Maxi M S G 1000 5000 10 000 1000 5000 10 000 1000 5000 10 000 1000 5000 10 000 1000 5000 10 000 2000 5000 10 000 1000 5000 - 1000 5000 - 1000 6000 - 1000 4000 - 1000 3500 - 1000 4000 - 500 2500 - 1000 2500 - 500 2500 - 500 2000 - 500 2000 - 500 1500 - 250 1000 - 1000 5000 - 1000 5000 - 1000 4000 - 1000 3500 - 1000 3000 - 2000 - 500 500 1500 - 1000 3000 - 3000 - 500 1000 3000 - 1000 3000 - 500 2000 - 1000 3000 - 2400 - 800 800 2400 - 500 2000 - 800 2400 - 200 1000 2000 - 500 250 1000 400 1600 - 250 1000 1200 - 400 100 500 1200 - 400 300 900 - 100 500 - 300 1000 - 300 1200 - 250 1000 - - 190 760 125 500 - - 125 500 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Moulded versions. pcs. per packaging unit/TPS* Mini Standard X Y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 90 540 170 680 170 680 170 680 75 450 160 640 136 544 112 448 56 336 96 384 48 288 88 176 88 176 36 216 36 144 60 480 51 408 84 252 72 144 66 132 54 108 27 108 21 84 * Tray-Packing-System 129 D Packing Units for Taped Capacitors with Radial Leads ROLL Size PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm 27.5 mm W 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 9 11 13 15 H 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 19 21 24 26 L 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 31.5 31.5 31.5 31.5 Codes 0B 0C 0D 0E 0F 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 1M 1N 2A 2B 2C 2D 2E 2F 2G 3A FA 3C 3D FB 3F 3G 3H 3I 4B FC 4C FD 4D FE 4F FF 4H 4J FG 4M 5A 5B 5D FH 5F FI 5G 5H 5I FJ 6A 6B 6D 6F Moulded versions. AMMO 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 A C B D 2800 - 2300 - 1800 - 1500 - 1200 - 2800 - 2300 - 2000 - 1500 - 1500 - 1400 - 1200 - 1200 - 1000 - 1000 - 1000 - 800 - 800 - 700 - 2500 - 2300 4150 1700 3100 1400 2800 1300 - 1100 - 1000 - - 1900 - 1450 - 1450 - 1400 - 1200 - 1200 - 1000 - 1000 - 740 - 1150 - 1200 - 1000 - 1000 - 850 - 850 - 740 - 740 - 650 - 650 - 590 - 540 - 770 - 640 - 550 - 480 - 450 - 380 - 360 - 360 - 350 - 310 - 420 - 350 - 290 - 250 Rights reserved to amend design data without prior notification. 11.10 * for 2-inch transport pitches. Samples and pre-production needs 1 packing unit minimum. H16.5 H18.5 N O 2200 2000 1500 1200 900 2200 2000 1600 1300 1300 1100 1000 1000 800 700 700 600 600 500 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - REEL P 360 P 500 H16.5 H18.5 H16.5 H18.5 F I H J 2500 - 2300 - 1800 - 1500 - 1200 - 2500 - 2300 - 2000 - 1500 - 1500 - 1400 - 1200 - 1200 - 1000 - 1000 - 950 - 800 - 800 - 700 - 2500 4400 2200 4300 1700 3200 1500 2900 1300 2500 1000 2200 900 1800 1100 2200 900 1600 900 1600 900 1600 700 1300 700 1300 550 1100 550 1100 400 800 600 1200 600 1200 500 1000 500 1000 450 900 450 900 400 800 400 800 350 700 350 700 300 650 300 600 - 800 - 700 - 600 - 500 - 480 - 420 - 400 - 400 - 380 - 350 - 460/340* - 380/280* - 300 - 270 130 D WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: Field 1 - 4: Type description Field 5 - 6: Rated voltage Field 7 - 10: Capacitance Field 11 - 12: Size and PCM Field 13 - 14: Special features (e.g. Snubber versions) Field 15: Capacitance tolerance Field 16: Packing Field 17 - 18: Lead length (untaped) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D 20 % bulk MKS 2 11.10 Type description: SMD-PET = SMD-PPS = FKP 02 = MKS 02 = FKS 2 = FKP 2 = MKS 2 = MKP 2 = FKS 3 = FKP 3 = MKS 4 = MKP 4 = MKP 10 = FKP 4 = FKP 1 = MKP-X2 = MKP-X2 R = MKP-Y2 = MP 3-X2 = MP 3-X1 = MP 3-Y2 = MP 3R-Y2 = Snubber MKP = Snubber FKP = GTO MKP = DC-LINK MKP 4 = DC-LINK MKP C = DC-LINK HC = SuperCap C = SuperCap MC = SuperCap R = SuperCap MR = 63 VDC SMDT SMDI FKP0 MKS0 FKS2 FKP2 MKS2 MKP2 FKS3 FKP3 MKS4 MKP4 MKP1 FKP4 FKP1 MKX2 MKXR MKY2 MPX2 MPX1 MPY2 MPRY SNMP SNFP GTOM DCP4 DCPC DCH_ SCSC SCMC SCSR SCMR Rated voltage: 2.5 VDC = A1 4 VDC = A2 14 VDC = A3 28 VDC = A4 40 VDC = A5 5 VDC = A6 50 VDC = B0 63 VDC = C0 100 VDC = D0 160 VDC = E0 250 VDC = F0 400 VDC = G0 450 VDC = H0 600 VDC = I0 630 VDC = J0 700 VDC = K0 800 VDC = L0 850 VDC = M0 900 VDC = N0 1000 VDC = O1 1100 VDC = P0 1200 VDC = Q0 1250 VDC = R0 1500 VDC = S0 1600 VDC = T0 2000 VDC = U0 2500 VDC = V0 3000 VDC = W0 4000 VDC = X0 6000 VDC = Y0 250 VAC = 0W 275 VAC = 1W 300 VAC = 2W 400 VAC = 3W 440 VAC = 4W 500 VAC = 5W ... 0.01 mF Capacitance: 22 pF = 0022 47 pF = 0047 100 pF = 0100 150 pF = 0150 220 pF = 0220 330 pF = 0330 470 pF = 0470 680 pF = 0680 1000 pF = 1100 1500 pF = 1150 2200 pF = 1220 3300 pF = 1330 4700 pF = 1470 6800 pF = 1680 0.01 mF = 2100 0.022 mF = 2220 0.047 mF = 2470 0.1 mF = 3100 0.22 mF = 3220 0.47 mF = 3470 = 4100 1 mF 2.2 mF = 4220 4.7 mF = 4470 = 5100 10 mF = 5220 22 mF = 5470 47 mF 100 mF = 6100 220 mF = 6220 1F = A010 2.5 F = A025 50 F = A500 100 F = B100 110 F = B110 600 F = B600 1200 F = C120 ... - 2.5 x 6.5 x 7.2 Size: 4.8 x 3.3 x 3 Size 1812 4.8 x 3.3 x 4 Size 1812 5.7 x 5.1 x 3.5 Size 2220 5.7 x 5.1 x 4.5 Size 2220 7.2 x 6.1 x 3 Size 2824 7.2 x 6.1 x 5 Size 2824 10.2 x 7.6 x 5 Size 4030 12.7 x 10.2 x 6 Size 5040 15.3 x 13.7 x 7 Size 6054 2.5 x 7 x 4.6 PCM 2.5 3 x 7.5 x 4.6 PCM 2.5 2.5 x 6.5 x 7.2 PCM 5 3 x 7.5 x 7.2 PCM 5 2.5 x 7 x 10 PCM 7.5 3 x 8.5 x 10 PCM 7.5 3 x 9 x 13 PCM 10 4 x 9 x 13 PCM 10 5 x 11 x 18 PCM 15 6 x 12.5 x 18 PCM 15 5 x 14 x 26.5 PCM 22.5 6 x 15 x 26.5 PCM 22.5 9 x 19 x 31.5 PCM 27.5 11 x21 x 31.5 PCM 27.5 9 x 19 x 41.5 PCM 37.5 11 x 22 x 41.5 PCM 37.5 94 x 49 x 182 DCH_ 94 x 77 x 182 DCH_ ... Special features: Standard = 00 Version A1 = 1A Version A1.1.1 = 1B Version A1.2 = 1C ... = = = = = = = = = = = = = = = = = = = = = = = = = = = X1 X2 Y1 Y2 T1 T2 K1 V1 Q1 0B 0C 1A 1B 2A 2B 3A 3C 4B 4C 5A 5B 6A 6B 7A 7B H0 H1 Tolerance: 20 % = 10 % = 5% = 2.5 % = 1% = ... 6 -2 M K J H E Packing: AMMO H16.5 340 x 340 AMMO H16.5 490 x 370 AMMO H18.5 340 x 340 AMMO H18.5 490 x 370 REEL H16.5 360 REEL H16.5 500 REEL H18.5 360 REEL H18.5 500 ROLL H16.5 ROLL H18.5 BLISTER W12 180 BLISTER W12 330 BLISTER W16 330 BLISTER W24 330 Bulk Mini Bulk Standard Bulk Maxi TPS Mini TPS Standard ... = = = = = = = = = = = = = = = = = = = A B C D F H I J N O P Q R T M S G X Y Lead length (untaped) 3.5 0.5 = C9 6 -2 = SD 16 1 = P1 ... The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 125