11-21/BHC-YR1S1/2T - Everlight International Corp.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Technical Data Sheet

1206 Package Chip LED with Inner Lens

11-21/BHC-YR1S1/2T

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain within RoHS complaint version.

Descriptions

․The 11-21 SMD LED is much smaller than lead

frame type components, thus enable smaller board

size, higher packing density, reduced storage space

and finally smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide Chip

Part No. Material Emitted Color Resin Color

11-21/BHC-YR1S1/2T InGaN Blue Water Clear

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 2 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Package Outline Dimensions

Notes: The tolerances unless mentioned are ±0.1, unit=mm.

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 3 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit

Reverse Voltage VR 5 V

Forward Current IF 25 mA

Peak Forward Current

(Duty 1/10 @1KHz) IFP 100 mA

Power Dissipation Pd 95 mW

Electrostatic Discharge(HBM) ESD 150 V

Operating Temperature Topr -40 ~ +85 ℃

Storage Temperature Tstg -40 ~ +90 ℃

Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec.

Hand Soldering : 350 ℃ for 3 sec.

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Min. Typ. Max. Unit Condition

Luminous Intensity Iv 112 ----- 225 mcd

Viewing Angle 2θ1/2 ----- 60 ----- deg

Peak Wavelength λp ----- 468 ----- nm

Dominant Wavelength λd 470 ----- 475

nm

Spectrum Radiation

Bandwidth △λ ----- 25 -----

nm

Forward Voltage VF 2.70 3.30 3.70

V

IF =20mA

Reverse Current IR ----- ----- 50 μA VR =5V

Notes:

1.Tolerance of Luminous Intensity: ±11%

2.Tolerance of Dominant Wavelength: ±1nm

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 4 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Bin Range Of Dom. Wavelength

Bin Min Max Unit Condition

Y 470 475 nm IF =20mA

Bin Range Of Luminous Intensity

Bin Min Max Unit Condition

R1 112 140

R2 140 180

S1 180 225

mcd IF =20mA

Notes:

1.Tolerance of Luminous Intensity: ±11%

2.Tolerance of Dominant Wavelength: ±1nm

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 5 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Typical Electro-Optical Characteristics Curves

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 6 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Label explanation

CAT: Luminous Intensity Rank

HUE: Dom. Wavelength Rank

REF: Forward Voltage Rank

Reel Dimensions

Note: The tolerances unless mentioned are ±0.1, Unit = mm.

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 7 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: The tolerances unless mentioned are ±0.1, Unit = mm.

Moisture Resistant Packaging

Label Aluminum moisture-proof bag Desiccant Label

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 8 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.

Confidence level : 90 %

LTPD : 10 %

No. Items Test Condition

Test

Hours/Cycles Sample

Size Ac/Re

1 Reflow Soldering

Temp. : 260℃±5℃

Min. 5sec. 6 Min. 22 PCS. 0/1

2 Temperature Cycle

H : +100℃ 15min

∫ 5 min

L : -40℃ 15min

300 Cycles 22 PCS. 0/1

3 Thermal Shock

H : +100℃ 5min

∫ 10 sec

L : -10℃ 5min

300 Cycles 22 PCS. 0/1

4 High Temperature

Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1

5 Low Temperature

Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1

6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1

7 High Temperature /

High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 9 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.

If unused LEDs remain, it should be stored in moisture proof packages.

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

11-21/BHC-YR1S1/2T

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 10 of 10

Device No:DSE-0001750 Prepared date: 16-Jun-2009 Prepared by: Cheng Dejiang

4. Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do

soldering of each terminal. Be careful because the damage of the product is often started at the time of

the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a

double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether

the characteristics of the LEDs will or will not be damaged by repairing.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306

Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com