U.FL-R-SMT(01) - Hirose Electric

Ultra Small SMT Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height

U.FL Series

2003.9

1.9(2.0Max)

2.4(2.5Max)

3(3.2Max)

U.FL-LP(V)-040

U.FL-LP-040

U.FL-LP-066

E.FL-LP-040

E.FL-LP-066

U.FL Series E.FL Series

2.5Max

2.0Max2.4Max2.4Max

U.FL-LP-040

U.FL-LP-066

U.FL-LP(V)-040

U.FL-LP-062

U.FL-LP-088

U.FL-R-SMT

Dia.0.81Dia.1.32

Dia.1.13

Dia.0.81Dia.1.0Dia.1.37

■Features

1. Low Pr ofile: 1.9mm or 2.4mm Nom. Mated Height

Height from the circuit board is 2.0mm or 2.5mm maximum

when a plug (right angle) is mated to a receptacle, which ranks

with world’s smallest class.

2.Extremely Small Occupied Mounting Area

In comparison with our SMT coaxial connectors E.FL series, the

receptacle provides a reduction of approximately 18% of

occupied mounting surface, which is only 7.7mm2.

3.Light Weight

One of the world’s lightest coaxial connectors.

Receptacle: 15.7mg

4.Applicable Up to 6 GHz Frequency

To meet the frequency requirements of a wide variety of

miniature equipment, these connectors offer high frequency

performance from DC to 6 GHz.

5.Board placement with automatic equipment

Supplied on tape-and-reel packaging.

6.Use of Ultra-fine Teflon Cable

From among the types of applicable cable, dia. 0.81mm(single

shielded) ultra-fine Teflon coaxial cable has been made a

standard specification in construction area.

Refer to the following pages for different cable types.

7.Simple Removal of Connector

The extraction jig permits simple removal of connectors.

8.User Friendly Mating Operation

Tactile lock feeling ensures engagement even with this small

size.

■Applications

Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS,

electronic measuring instruments, etc.

Mated Height Comparison

(With Hirose Product)

●Space Factor of Mated Connector

Meets up to 6 GHz Requirement

NEW

■Product Specifications

*V.S.W.R. Measurement System

The above V.S.W.R. standard values were measured using the measurement system of the diagram below.

Note 1: Cable type connectors were measured with SMA conversion adapters

attached to both ends of the harness product of a suitable 100cm cable.

Note 2: Board type connectors were mounted to a 50Ωglass epoxy board and

measurements were conducted with SMA conversion adapters attached.

Ratings

Nominal characteristic impedance

Voltage rating

Frequency range

50 ohms

60 V AC (rms)

DC to 6 GHz

Operating temperature range

Operating humidity

-40˚C to +90˚C

90% max.

Part Material Finish Remarks

Shell Phosphor bronze Silver plating —————

Male center contact Brass Gold plating —————

Female center contact Phosphor bronze Gold plating —————

Insulator Plug Color: Black UL94V-0

Receptacle Color: Beige UL94V-0LCP

PBT

■Materials

1. Contact resistance

2. Insulation resistance

3. Withstanding voltage

4. V.S.W.R.*

5. Female contact holding force

6. Durability

(mating/un-mating,

with corresponding plug)

7. Vibration

8. Shock

9. Humidity

(Steady state)

10. Temperature cycle

11. Salt spray test

Item Specification Conditions

Center: 20 m ohms max.

Outside: 10 m ohms max.

500 M ohms min.

No flashover or insulation breakdown.

0.15 N min.

Contact resistance

Center: 25 m ohms max.

Outside: 15 m ohms max.

No electrical discontinuity of 1µs min.

No damage, cracks or parts dislocation.

Insulation resistance 100 M ohms min.(when humidity high)

Insulation resistance 500 M ohms min.(when dry)

No damage, cracks or parts dislocation.

Contact resistance:25 m ohms max. (Center)

15 m ohms max. (Outside)

No excessive corrosion

10 mA max.

100 V DC

200 V AC / 1 minute

Measured with a Ø 0.475 pin gauge

30 cycles

Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration

of 59m/s

, for 5 cycles in the direction of each of the 3 axis.

Acceleration of 735 m/s2, 11ms duration, sine half-wave

waveform, 2 cycles in each of 3 axes.

96 hours at temperature of 40ç and humidity of 95%.

Temperature:-40˚C

+5 to +35˚C

+90˚C

+5 to +35˚C

Time: 30

5 max.

(Minutes)

5 cycles

5% salt water solution, 48 hours

Part No. Up to 3GHz 3 to 6GHz

U.FL-LP-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.35 Max

U.FL-LP(V)-040 dia.0.81mm Coaxial Cable Assembly 1.3 Max 1.3 Max

U.FL-LP-066 dia.1.13mm Coaxial Cable Assembly 1.3 Max 1.4 Max

U.FL-LP-066 dia.1.32mm Coaxial Cable Assembly 1.3 Max 1.5 Max

U.FL-LP-062 dia.1mm Coaxial Cable Assembly 1.3 Max 1.3 Max

U.FL-LP-088 dia.1.37mm Coaxial Cable Assembly 1.3 Max 1.4 Max

Part No.

Mated Height

Applicable

cable

Weight (mg)

2.5mm Max. 2.5mm Max. 2.0mm Max. 2.4mm Max. 2.4mm Max.

(2.4mm Nom.) (2.4mm Nom.) (1.9mm Nom.) (2.3mm Nom.) (2.3mm Nom.)

Dia. 0.81mm Dia. 0.81mm Dia. 1mm Dia. 1.37mm

Coaxial cable Coaxial cable Coaxial cable Coaxial cable

Dia. 0.81mm Dia. 0.81mm Dia. 1mm Dia. 1.37mm

Coaxial cable Coaxial cable Coaxial cable Coaxial cable

53.7 59.1 34.8 45.5 71.7

Dia. 1.13mm and

Dia. 1.32mm

Coaxial cable

■Cable Assembly (Plug)

●Cable Guide

■How to Specify Cable Assembled Plug

Dimension of U.FL Series assembly products should be made as indicated below.

Double-Ended Cable Assembly Single-Ended Cable Assembly

U.FL - [] LP - [] - A - (L)

●Ordering Information

Series name U.FL

Total Length(mm)

00350<

=L<

=00200

02000<L<

=00500

05000<L<

=01000

10000<0L<

=1000

Standard Tolerance (mm)

±04

±08

±12

±1.5%

●

Total Standard Tolerance for Total Length of Cable Assembly

Note: Shortest length L is 35 mm.

31 2 4

Assembly type LP: Single ended

2LP: Double ended

Cable type 04 : Dia.0.81mm Coaxial Cable

068 : Dia.1.13mm Coaxial Cable

066 : Dia.1.32mm Coaxial Cable

062 : Dia.1 mm Coaxial Cable

088 : Dia.1.37mm Coaxial Cable

Total Length(mm) Length is expressed in mm units.

Please contact Hirose Sales Representative for cable length and cable end treatment.

U.FL-LP-040 U.FL-LP-062 U.FL-LP-088

Dia.0.81mm

Coaxial Cable 04 7/0.05 SA

(AWG36)

Dia.0.40

PFA

Single

Shield SA

Dia.0.81

PFA 50 ohms 6.45dB/m 9.42dB/m

Dia.1.13mm

Coaxial Cable 068 7/0.08 SA

(AWG32)

Dia.0.68

FEP

Single

Shield SA[TA]

Dia.1.13

FEP 50 ohms 3.43dB/m

[3.73dB/m]

5.13dB/m

[5.44dB/m]

Dia.1.32mm

Coaxial Cable 066 7/0.08 SA

(AWG32)

Dia.0.66

FEP

Double

Shield TA

Dia.1.32

FEP 50 ohms 3.8dB/m 5.6dB/m

Dia.1mm

Coaxial Cable 062 7/0.071 SA

(AWG33)

Dia.0.62

FEP

Tape, single

Shield TAT

Dia.1

FEP 50 ohms 3.1dB/m 4.4dB/m

Dia.1.37mm

Coaxial Cable

(data as provided by material suppliers, for reference only)

* SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin

088 7/0.102 SA

(AWG30)

Dia.0.88

FEP

Single

Shield TA

Dia.1.37

FEP 50 ohms 2.8dB/m 4.3dB/m

Description Cable

Type

Cable Specification

Inner

Conductor*

Dielectric

Diameter

Outer

Conductor*

Jacket

Diameter

Nominal

Impedance

Nominal attenuation

At 3GHz At 6GHz

1.93

1.85

U.FL-LP-066

1.93

U.FL-LP(V)-040

3.4

2.8

1.5

2.8

1.8

Part No.

U.FL-R-SMT(01)

U.FL-R-SMT(10)

CL No.

331-0471-0-01

331-0471-0-10

Packaging

Bag packaging (100 pieces/bag)

Reel packaging (2500 pieces/reel)

Weight (mg)

15.7/unit

■Receptacles

Note 1: Receptacles of (01) specification are sold by the

pack with 100 pieces per pack.

Please order in pack units.

Note 2: Receptacles of (10) specification are sold by the

reel (which contains 2,500 pieces).

Please order in reel units.

Note 3: Permissible value for mold resin which gets onto

the center contact.

●Packaging Specifications

Embossed Carrier Tape Dimensions

Reel Dimensions

GND GND

GND

Cut Out Prohibition Area

Recommended PCB Footprints

SIG

Ø2

2.6

0.6

1.25

0.35

1.05±0.05 1±0.05

1±0.05

2.2±0.05

4±0.05

1.9±0.05

1.2Max(NOTE 3)

(3.1)

2.6

1.8

1.75±0.1

12±0.3

8±0.1

2±0.1 4±0.1 0.3

1.6

Center contact

Unreeling direction

5.5±0.1

Ø1.5

+0.1

1.8 14

Ø13

Ø21

Ø330±2

Part No.

HRMP-U.FLJ

CL No.

311-0300-2

■Conversion Adapter

●SMA Conversion Adapter

(Mating portion: U.FL side jack - SMA side plug)

Note:

The U.FL side mating portions has a lower lock retention

force than the regular product, therefore, cannot be used

for purposes other than performance measurements.

(10.7) 8HEX

1.1

Ø1.9

Part No.

U.FL-R-1

CL No.

331-0466-0

■Receptacle for Check

This receptacle is used for inspecting the continuity, withstand

voltage, and other aspects of the harness product.

This receptacle is used for check the continuity, withstanding

voltage, and other performance of the cable assembly products.

Note: Part No. U.FL-LP-N-2 for U.FL-LP-040/066/088.

Part No. U.FL-LP(V)-N-2 for U.FL-LP(V)-040/U.FL-LP-062.

12.9

57HEX

M5×0.5

(7.9)

(4.4)

Part No.

U.FL-LP-N-2

U.FL-LP(V)-N-2

CL No.

331-0494-5

331-0493-2

■Extraction Jig

This jig is used for extraction from a mating condition.

U.FL

Ø15

(90)

2.1

Part No.

HRMJ-U.FLP

CL No.

311-0301-5

●SMA Conversion Adapter

(Mating portion: U.FL side plug - SMA side jack)

Note:

The U.FL side mating portions has a lower lock retention

force than the regular product, therefore, cannot be used

for purposes other than performance measurements.

14.05

Ø6.35

1/4-36UNS-2A

6 5.6(4.05)

Part No.

HRMJ-U.FLP-ST1

CL No.

311-0385-5

●SMA Conversion Adapter

(Mating portion: U.FL side plug-SMA side jack)

Note: This connector is used by compressing the mated

portion of U.FL side onto the U.FL-R-SMT portion.

(18.6)

1/4-36UNS-2A

65.5

(4)

■Usage Precautions

1. Plugs

(1) Connection/

disconnection of

connectors

(2) Permissible load on

the cable after

connector mating.

(3) Precautions

1) To disconnect connectors, hook the end portion of U.FL-LP-N-2 and U.FL-LP(V)-N-2 onto the connector cover and

pull off vertically in the direction of the connector mating axis.

1) To remove the connector directly, hold the connector cover and pull off

vertically in the direction of the connector mating axis.

(Please exercise caution so as not to injure fingertips or nails.)

2) To mate the connectors, the mating axes of both connectors are aligned

and the connectors are inserted as perpendicularly as possible.

Do not attempt to insert on an extreme angle.

After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram

below.

Do NOT forcefully twist or deform wires.

(1) Recommended

temperature profile

(Reference)

1) The temperature profile indicates the board surface temperature at the point of contacts with the connector

terminals (for surface mounted receptacle).

2) The temperature profile will change depending on conditions which include such factors as the size of the board,

the solder used, and the solder thickness.

(3) Recommended screen

thickness 0.1 to 0.15 mm

(2) Recommended

manual soldering

(Reference) Manual soldering: 350˚C for 5 seconds

2. Receptacles

U.FL-LP-040 2N max.

2N max.

4N max.

U.FL-R-SMT

Temperature on

Top Portion of Part

Time

Preheating

(130 to 165℃)

Within 2 minutes

40 to 50

seconds

Heating peak

240℃ 3 seconds

183℃

260

240

220

200

180

160

140

120

100

(℃)

Extraction Jig

U.FL-R-SMT

U.FL Cable

Assembly

NOTES :

8The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.

USA:

HIROSE ELECTRIC U.S.A., INC.

2688 Westhills Court, Simi Valley, CA 93065-6235

Phone : 1 805 522 7958

Fax : 1 805 522 3217

http://www.hirose.com

UNITED KINGDOM:

HIROSE ELECTRIC UK LTD.

Crownhill Business Centre 22 Vincent Avenue

Crownhill, Milton Keynes MK8 OAB

Phone : 44 1908 305400

Fax : 44 1908 305401

http://www.hirose.co.uk

HONG KONG:

HIROSE ELECTRIC CO., LTD.

Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha

Tsui East, Kowloon

Phone : 852 2803 5338

Fax : 852 2591 6560

EUROPE BRANCH:

HIROSE ELECTRIC CO., LTD.

Beechavenue 46.1119PV

Schiphol-Rijk,The Netherlands

Phone : 31 20 6557460

Fax : 31 20 6557469

http://hiroseeurope.com

KOREA:

HIROSE KOREA CO., LTD.

(#2NA311,Shihwa Industrial Complex),

1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do

Phone : 82 31 496 7000,7124

Fax : 82 31 496 7100

http://www.hirose.co.kr

TAIWAN:

HIROSE ELECTRIC CO., LTD.

No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei

Phone : 886 2 2557 7351,7352

Fax : 886 2 2552 9851

GERMANY:

HIROSE ELECTRIC GmbH

Zeppelinstrasse 42 D-73760 Ostfildern Kemnat

Phone : 49 711 4560021

Fax : 49 711 4560729

http://www.hirose.de

CHINA:

HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD.

3705,Bund Center,222 Yan An Road(E),Shanghai 20002

Phone : 86 21 6335 2538

Fax : 86 21 6335 0767

SINGAPORE:

HIROSE ELECTRIC CO., LTD.

10 Anson Road #34-13 International Plaza 079903

Phone : 65 6324 6113

Fax : 65 6324 6123

5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN

PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933