TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 D D Fully Specified for 3.3-V and 5-V Operation Wide Power Supply Compatibility 2.5 V - 5.5 V Output Power for RL = 8 - 350 mW at VDD = 5 V, BTL - 250 mW at VDD = 5 V, SE - 250 mW at VDD = 3.3 V, BTL - 75 mW at VDD = 3.3 V, SE D D D D D D Shutdown Control - IDD = 7 A at 3.3 V - IDD = 60 A at 5 V BTL to SE Mode Control Integrated Depop Circuitry Thermal and Short-Circuit Protection Surface Mount Packaging - SOIC - PowerPAD MSOP D OR DGN PACKAGE (TOP VIEW) description The TPA311 is a bridge-tied load (BTL) or SHUTDOWN VO - 1 8 single-ended (SE) audio power amplifier develBYPASS GND 2 7 oped especially for low-voltage applications SE/BTL VDD 3 6 where internal speakers and external earphone 4 5 IN V O+ operation are required. Operating with a 3.3-V supply, the TPA311 can deliver 250-mW of continuous power into a BTL 8- load at less than 1% THD+N throughout voice band frequencies. Although this device is characterized out to 20 kHz, its operation was optimized for narrower band applications such as cellular communications. The BTL configuration eliminates the need for external coupling capacitors on the output in most applications, which is particularly important for small battery-powered equipment. A unique feature of the TPA311 is that it allows the amplifier to switch from BTL to SE on the fly when an earphone drive is required. This eliminates complicated mechanical switching or auxiliary devices just to drive the external load. This device features a shutdown mode for power-sensitive applications with special depop circuitry to virtually eliminate speaker noise when exiting shutdown mode and during power cycling. The TPA311 is available in an 8-pin SOIC surface-mount package and the surface-mount PowerPAD MSOP, which reduces board space by 50% and height by 40%. VDD 6 RF VDD/2 Audio Input RI 4 IN 2 BYPASS 1 SHUTDOWN CS - CI VO+ 5 CC + CBF From System Control From HP Jack 3 SE/BTL - Bias Control VO- 8 + 350 mW 7 GND Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. Copyright 2000, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 AVAILABLE OPTIONS PACKAGED DEVICES TA SMALL OUTLINE (D) MSOP Symbolization MSOP (DGN) - 40C to 85C TPA311D TPA311DGN AAB The D and DGN packages are available taped and reeled. To order a taped and reeled part, add the suffix R to the part number (e.g., TPA311DR). Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION I BYPASS is the tap to the voltage divider for internal mid-supply bias. This terminal should be connected to a 0.1-F to 1-F capacitor when used as an audio amplifier. BYPASS 2 GND 7 IN 4 I IN is the audio input terminal. SE/BTL 3 I When SE/BTL is held low, the TPA311 is in BTL mode. When SE/BTL is held high, the TPA311 is in SE mode. SHUTDOWN 1 I SHUTDOWN places the entire device in shutdown mode when held high (IDD = 60 A, VDD = 5 V). VDD VO+ 6 5 O VDD is the supply voltage terminal. VO+ is the positive output for BTL and SE modes. VO- 8 O VO- is the negative output in BTL mode and a high-impedance output in SE mode. GND is the ground connection. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VDD +0.3 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (see Dissipation Rating Table) Operating free-air temperature range, TA (see Table 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 85C Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 150C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATING TABLE D TA 25C 725 mW DGN 2.14 W PACKAGE DERATING FACTOR 5.8 mW/C TA = 70C 464 mW TA = 85C 377 mW 17.1 mW/C 1.37 W 1.11 W Please see the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report (literature number SLMA002), for more information on the PowerPAD package. The thermal data was measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD on page 33 of the before mentioned document. recommended operating conditions AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AAA AAA Supply voltage, VDD Operating free-air temperature, TA (see Table 3) 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN MAX 2.5 5.5 UNIT V - 40 85 C TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 electrical characteristics at specified free-air temperature, VDD = 3.3 V, TA = 25C (unless otherwise noted) AAA AAAAAAAAAAAAAAA AAAAAAAAA AAA AAA AAA AAA AAA AAAAAAAAAAAAAAA AAAAAA AAAA AAA AAA AAA AAA AAAAAAAAA AAA AAAAAAAAAAAAAAA AAAAAA AAAA AAA AAA AAA AAA AAA AAAAAAAAAAAAAAA AAAAAAAAA AAA AAA AAA A AA AAAAAA AAAA AAA AAA AAAAAAAAAAAAAAA AAAAAAAAA AAA AAA AAA AAA AAA AAAAAAAAAAAAAAA AAAAAAAAA A AA A AA AAA AAA AAA AAA PARAMETER TEST CONDITIONS VOO Output offset voltage (measured differentially) See Note 1 PSRR Power supply rejection ratio VDD = 3 3.2 2 V to 3 3.4 4V IDD Supply current (see Figure 6) IDD(SD) Supply current, shutdown mode (see Figure 7) MIN TYP MAX 5 20 BTL mode 85 SE mode 83 UNIT mV dB BTL mode 0.7 1.5 SE mode 0.35 0.75 7 50 mA A NOTE 1: At 3 V < VDD < 5 V the dc output voltage is approximately VDD/2. operating characteristics, VDD = 3.3 V, TA = 25C, RL = 8 AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAAAAAAA AAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAAAAAAA AAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA PARAMETER TEST CONDITIONS THD = 0.5%, BTL mode, THD = 0.5%, SE mode MIN See Figure 14 PO Output power, power see Note 2 THD + N Total harmonic distortion plus noise PO = 250 mW, See Figure 12 f = 20 Hz to 4 kHz, Gain = 2, Maximum output power bandwidth Gain = 2, THD = 3%, See Figure 12 Unity-gain bandwidth Open Loop, See Figure 36 f = 1 kHz, See Figure 5 CB = 1 F, BTL mode, f = 1 kHz, See Figure 3 CB = 1 F, SE mode, Gain = 1, BTL, CB = 0.1 F, See Figure 42 RL = 32 , BOM B1 Supply ripple rejection ratio Vn Noise output voltage TYP 250 110 MAX UNIT mW 1.3% 10 kHz 1.4 MHz 71 dB 86 15 V(rms) NOTE 2: Output power is measured at the output terminals of the device at f = 1 kHz. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25C (unless otherwise noted) AAAA AAAAAAAAAAAAAA AAAAAAAAAA AAA AAA AAA AAA AAAA AAAAAAAAAAAAAA AAAAAAA AAAA AAA AAA AAA AAA AAAAAAAAAA AAAA AAAAAAAAAAAAAA AAAAAAA AAAA AAA AAA AAA AAA AAAA AAAAAAAAAAAAAA AAAAAAAAAA AAA AAA AAA AAA AAAAAAA AAAA AAAA AAAAAAAAAAAAAA AAAAAAAAAA AAA AAA AAA AAA AAAA AAAAAAAAAAAAAA AAAAAAAAAA A AA A AA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA A AAA AA A AAA AA AAA A AAA AA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA AAAA AAAAAAAAAA AAAAA AAAAAA AAAAA AAA AAA AAA AAA PARAMETER TEST CONDITIONS VOO Output offset voltage (measured differentially) PSRR Power supply rejection ratio IDD Supply current (see Figure 6) IDD(SD) Supply current, shutdown mode (see Figure 7) VDD = 4 4.9 9 V to 5.1 51V MIN TYP MAX 5 20 BTL mode 78 SE mode 76 UNIT mV dB BTL mode 0.7 1.5 SE mode 0.35 0.75 60 100 mA A operating characteristics, VDD = 5 V, TA = 25C, RL = 8 PARAMETER BTL mode, THD = 0.5%, SE mode Total harmonic distortion plus noise PO = 350 mW, See Figure 16 f = 20 Hz to 4 kHz, Gain = 2, Maximum output power bandwidth Gain = 2, THD = 2%, See Figure 16 Unity-gain bandwidth Open Loop, See Figure 37 f = 1 kHz, See Figure 5 CB = 1 F, BTL mode, f = 1 kHz, See Figure 4 CB = 1 F, SE mode, Gain = 1, BTL, CB = 0.1 F, See Figure 43 RL = 32 , Output power, power see Note 2 THD + N Supply ripple rejection ratio Vn MIN THD = 0.5%, PO BOM B1 TEST CONDITIONS Noise output voltage See Figure 18 POST OFFICE BOX 655303 700 300 NOTE 2: Output power is measured at the output terminals of the device at f = 1 kHz. 4 TYP * DALLAS, TEXAS 75265 MAX UNIT mW 1% 10 kHz 1.4 MHz 65 dB 75 15 V(rms) TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 PARAMETER MEASUREMENT INFORMATION VDD 6 RF VDD/2 Audio Input RI VDD CS 1 F 4 IN 2 BYPASS - CI VO+ 5 + CB 0.1 F RL = 8 - VO- 8 + 7 1 SHUTDOWN 3 SE/BTL GND Bias Control Figure 1. BTL Mode Test Circuit VDD 6 RF Audio Input RI VDD CS 1 F VDD/2 4 IN 2 BYPASS - CI VO+ 5 + CC 330 F CB 0.1 F RL = 32 - VO- 8 + 7 VDD 1 SHUTDOWN 3 SE/BTL GND Bias Control Figure 2. SE Mode Test Circuit POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS Table of Graphs FIGURE IDD PO Supply voltage rejection ratio vs Frequency Supply current vs Supply voltage Output power THD + N Vn PD 3, 4, 5 6, 7 vs Supply voltage 8, 9 vs Load resistance 10, 11 vs Frequency 12, 13, 16, 17, 20, 21, 24, 25, 28, 29, 32, 33 vs Output power 14, 15, 18, 19, 22, 23, 26, 27, 30, 31, 34, 35 Total harmonic distortion plus noise Open loop gain and phase vs Frequency 36, 37 Closed loop gain and phase vs Frequency 38, 39, 40, 41 Output noise voltage vs Frequency 42, 43 Power dissipation vs Output power 44, 45, 46, 47 TYPICAL CHARACTERISTICS SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY VDD = 3.3 V RL = 8 SE -10 -20 CB = 0.1 F -30 -40 -50 CB = 1 F -60 -70 -80 BYPASS = 1/2 VDD -90 100 VDD = 5 V RL = 8 SE -10 -20 CB = 0.1 F -30 -40 -50 CB = 1 F -60 -70 BYPASS = 1/2 VDD -80 -90 -100 20 0 Supply Voltage Rejection Ratio - dB Supply Voltage Rejection Ratio - dB 0 SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY 1k 10 k 20 k -100 20 f - Frequency - Hz 1k f - Frequency - Hz Figure 3 6 100 Figure 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 k 20 k TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs SUPPLY VOLTAGE SUPPLY VOLTAGE REJECTION RATIO vs FREQUENCY 1.1 0 RL = 8 CB = 1 F BTL 0.9 I DD- Supply Current - mA -20 -30 -40 -50 VDD = 5 V -60 -70 VDD = 3.3 V -80 BTL 0.7 0.5 SE 0.3 0.1 -90 -0.1 -100 20 100 1k 2 10 k 20 k 3 4 5 6 VDD - Supply Voltage - V f - Frequency - Hz Figure 5 Figure 6 SUPPLY CURRENT (SHUTDOWN) vs SUPPLY VOLTAGE 90 SHUTDOWN = High 80 I DD(SD) - Supply Current - A Supply Voltage Rejection Ratio - dB -10 70 60 50 40 30 20 10 0 2 2.5 3 3.5 4 4.5 5 5.5 VDD - Supply Voltage - V Figure 7 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS OUTPUT POWER vs SUPPLY VOLTAGE OUTPUT POWER vs SUPPLY VOLTAGE 1000 350 THD+N 1% BTL THD+N 1% SE 300 PO - Output Power - mW PO - Output Power - mW 800 600 RL = 8 400 RL = 32 250 200 RL = 8 150 100 RL = 32 200 50 0 2 2.5 3 3.5 4 4.5 5 0 5.5 2.5 2 3 VDD - Supply Voltage - V Figure 8 5 4.5 5.5 OUTPUT POWER vs LOAD RESISTANCE 800 350 THD+N = 1% BTL 700 THD+N = 1% SE 300 600 PO - Output Power - mW PO - Output Power - mW 4 Figure 9 OUTPUT POWER vs LOAD RESISTANCE VDD = 5 V 500 400 300 VDD = 3.3 V 200 250 200 VDD = 5 V 150 100 50 100 VDD = 3.3 V 0 8 16 24 32 40 48 56 64 0 8 14 RL - Load Resistance - 20 26 32 Figure 11 POST OFFICE BOX 655303 38 44 50 RL - Load Resistance - Figure 10 8 3.5 VDD - Supply Voltage - V * DALLAS, TEXAS 75265 56 62 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 10 VDD = 3.3 V PO = 250 mW RL = 8 BTL THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10 AV = -20 V/V 1 AV = -10 V/V AV = -2 V/V 0.1 0.01 20 100 1k 10k 20k PO = 125 mW 0.1 PO = 250 mW 100 1k f - Frequency - Hz f - Frequency - Hz Figure 12 Figure 13 10k 20k TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % PO = 50 mW 1 0.01 20 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER VDD = 3.3 V f = 1 kHz AV = -2 V/V BTL 1 RL = 8 0.1 0.01 0.04 VDD = 3.3 V RL = 8 AV = -2 V/V BTL 0.1 0.16 0.22 0.28 0.34 0.4 f = 20 kHz f = 10 kHz 1 f = 1 kHz 0.1 f = 20 Hz 0.01 0.01 PO - Output Power - W VDD = 3.3 V RL = 8 AV = -2 V/V BTL 0.1 1 PO - Output Power - W Figure 14 Figure 15 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 10 VDD = 5 V PO = 350 mW RL = 8 BTL THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10 AV = -20 V/V 1 AV = -10 V/V AV = -2 V/V 0.1 0.01 20 100 1k 10k VDD = 5 V RL = 8 AV = -2 V/V BTL 1 PO = 175 mW 0.1 PO = 350 mW 0.01 20 20k 100 f - Frequency - Hz 20k TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10k Figure 17 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER VDD = 5 V f = 1 kHz AV = -2 V/V BTL 1 RL = 8 0.1 0.25 0.40 0.55 0.70 0.85 1 f = 20 kHz f = 10 kHz 1 f = 1 kHz 0.1 f = 20 Hz VDD = 5 V RL = 8 AV = -2 V/V BTL 0.01 0.01 PO - Output Power - W 0.1 PO - Output Power - W Figure 18 10 1k f - Frequency - Hz Figure 16 0.01 0.1 PO = 50 mW Figure 19 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10 VDD = 3.3 V PO = 30 mW RL = 32 SE 1 0.1 AV = -1 V/V AV = -10 V/V 0.01 AV = -5 V/V 0.001 20 100 1k 10k VDD = 3.3 V RL = 32 AV = -1 V/V SE 1 PO = 10 mW 0.1 0.01 PO = 15 mW PO = 30 mW 0.001 20 20k 100 f - Frequency - Hz Figure 20 20k TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10k Figure 21 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER VDD = 3.3 V f = 1 kHz RL = 32 AV = -1 V/V SE 1 0.1 0.01 0.02 1k f - Frequency - Hz 0.025 0.03 0.035 0.04 0.045 0.05 VDD = 3.3 V RL = 32 AV = -1 V/V SE f = 20 kHz 1 f = 10 kHz 0.1 f = 1 kHz f = 20 Hz 0.01 0.002 PO - Output Power - W 0.01 0.02 0.03 0.05 PO - Output Power - W Figure 22 Figure 23 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10 VDD = 5 V PO = 60 mW RL = 32 SE 1 AV = -10 V/V 0.1 AV = -5 V/V 0.01 AV = -1 V/V 0.001 20 100 1k 1 PO = 15 mW 0.1 PO = 30 mW 0.01 PO = 60 mW 0.001 20 20k 10k VDD = 5 V RL = 32 AV = -1 V/V SE 100 f - Frequency - Hz Figure 24 10 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 20k TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 VDD = 5 V f = 1 kHz RL = 32 AV = -1 V/V SE 1 0.1 0.04 0.06 0.08 0.1 0.12 0.14 f = 20 kHz 1 f = 10 kHz f = 1 kHz 0.1 f = 20 Hz 0.01 0.002 PO - Output Power - W VDD = 5 V RL = 32 AV = -1 V/V SE 0.01 PO - Output Power - W Figure 26 12 10k Figure 25 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 0.01 0.02 1k f - Frequency - Hz Figure 27 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 0.1 0.2 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 1 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 1 VDD = 3.3 V PO = 0.1 mW RL = 10 k SE 0.1 AV = -1 V/V AV = -2 V/V AV = -5 V/V 0.01 20 100 1k 10k VDD = 3.3 V RL = 10 k AV = -1 V/V SE PO = 0.05 mW 0.1 PO = 0.1 mW 0.01 20 20k PO = 0.13 mW 100 1k f - Frequency - Hz Figure 28 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER VDD = 3.3 V f = 1 kHz RL = 10 k AV = -1 V/V SE THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 10 0.1 0.01 0.001 50 75 100 125 20 k Figure 29 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 1 10 k f - Frequency - Hz 150 175 200 10 VDD = 3.3 V RL = 10 k AV = -1 V/V SE 1 f = 20 Hz 0.1 f = 20 kHz 0.01 f = 1 kHz f = 10 kHz 0.001 5 PO - Output Power - W 10 100 500 PO - Output Power - W Figure 30 Figure 31 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 1 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % 1 VDD = 5 V PO = 0.3 mW RL = 10 k SE 0.1 AV = -1 V/V AV = -2 V/V AV = -5 V/V 0.01 20 100 1k 10k VDD = 5 V RL = 10 k AV = -1 V/V SE PO = 0.3 mW 0.1 PO = 0.2 mW PO = 0.1 mW 0.01 20 20k 100 f - Frequency - Hz Figure 32 THD+N -Total Harmonic Distortion + Noise - % THD+N -Total Harmonic Distortion + Noise - % VDD = 5 V f = 1 kHz RL = 10 k AV = -1 V/V SE 0.1 0.01 125 200 275 350 425 500 10 VDD = 5 V RL = 10 k AV = -1 V/V SE 1 f = 20 kHz f = 20 Hz 0.1 0.01 f = 1 kHz f = 10 kHz 0.001 5 PO - Output Power - W 10 100 PO - Output Power - W Figure 34 14 20k TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 0.001 50 10k Figure 33 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 1 1k f - Frequency - Hz Figure 35 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 500 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS OPEN-LOOP GAIN AND PHASE vs FREQUENCY 40 180 VDD = 3.3 V RL = Open BTL Phase 30 120 20 60 10 0 0 Phase - Open-Loop Gain - dB Gain -60 -10 -120 -20 -30 1 101 102 103 104 -180 f - Frequency - kHz Figure 36 OPEN-LOOP GAIN AND PHASE vs FREQUENCY 40 180 VDD = 5 V RL = Open BTL Phase 30 120 20 60 10 0 0 Phase - Open-Loop Gain - dB Gain -60 -10 -120 -20 -30 1 101 102 103 104 -180 f - Frequency - kHz Figure 37 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS CLOSED-LOOP GAIN AND PHASE vs FREQUENCY 1 180 Phase 0.75 170 0.25 0 160 Gain -0.25 150 -0.5 -0.75 140 -1 -1.25 -1.5 -1.75 -2 101 Phase - Closed-Loop Gain - dB 0.5 VDD = 3.3 V RL = 8 PO = 0.25 W CI =1 F BTL 102 130 103 104 105 106 120 f - Frequency - Hz Figure 38 CLOSED-LOOP GAIN AND PHASE vs FREQUENCY 1 180 Phase 0.75 170 0.25 0 160 Gain -0.25 150 -0.5 -0.75 140 -1 -1.25 -1.5 -1.75 -2 101 VDD = 5 V RL = 8 PO = 0.35 W CI =1 F BTL 102 130 103 104 105 f - Frequency - Hz Figure 39 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 120 106 Phase - Closed-Loop Gain - dB 0.5 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS CLOSED-LOOP GAIN AND PHASE vs FREQUENCY 7 180 Phase 6 170 Gain 160 4 150 3 140 2 1 0 -1 -2 -3 101 VDD = 3.3 V RL = 32 AV = -2 V/V PO = 30 mW CI =1 F CC =470 F SE 102 Phase - Closed-Loop Gain - dB 5 130 120 110 103 104 105 106 100 f - Frequency - Hz Figure 40 CLOSED-LOOP GAIN AND PHASE vs FREQUENCY 7 180 Phase 6 170 Gain 160 4 150 3 140 2 1 0 -1 -2 101 VDD = 5 V RL = 32 AV = -2 V/V PO = 60 mW CI =1 F CC =470 F SE 102 Phase - Closed-Loop Gain - dB 5 130 120 110 103 104 105 106 100 f - Frequency - Hz Figure 41 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS OUTPUT NOISE VOLTAGE vs FREQUENCY 100 VDD = 3.3 V BW = 22 Hz to 22 kHz RL = 32 CB =0.1 F AV = -1 V/V Vn - Output Noise Voltage - V(rms) Vn - Output Noise Voltage - V(rms) 100 OUTPUT NOISE VOLTAGE vs FREQUENCY VO BTL 10 VO+ 1 20 100 1k 10 k VDD = 5 V BW = 22 Hz to 22 kHz RL = 32 CB =0.1 F AV = -1 V/V VO BTL 10 VO+ 1 20 20 k 100 1k f - Frequency - Hz Figure 42 POWER DISSIPATION vs OUTPUT POWER 300 80 72 PD - Power Dissipation - mW 270 PD - Power Dissipation - mW 20 k Figure 43 POWER DISSIPATION vs OUTPUT POWER 240 210 180 150 VDD = 3.3 V RL = 8 BTL 120 0 100 200 300 RL = 8 64 56 48 40 32 24 RL = 32 16 VDD = 3.3 V SE 8 90 400 0 0 PO - Output Power - mW 30 60 Figure 45 POST OFFICE BOX 655303 90 PO - Output Power - mW Figure 44 18 10 k f - Frequency - Hz * DALLAS, TEXAS 75265 120 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 TYPICAL CHARACTERISTICS POWER DISSIPATION vs OUTPUT POWER 720 180 640 160 PD - Power Dissipation - mW PD - Power Dissipation - mW POWER DISSIPATION vs OUTPUT POWER 560 480 400 320 VDD = 5 V RL = 8 BTL 240 200 400 600 800 1000 140 120 100 80 RL = 32 VDD = 5 V SE 60 160 0 RL = 8 1200 40 0 50 PO - Output Power - mW 100 150 200 250 300 PO - Output Power - mW Figure 46 Figure 47 APPLICATION INFORMATION bridge-tied load versus single-ended mode Figure 48 shows a linear audio power amplifier (APA) in a BTL configuration. The TPA311 BTL amplifier consists of two linear amplifiers driving both ends of the load. There are several potential benefits to this differential drive configuration but initially consider power to the load. The differential drive to the speaker means that as one side is slewing up, the other side is slewing down, and vice versa. This in effect doubles the voltage swing on the load as compared to a ground referenced load. Plugging 2 x VO(PP) into the power equation, where voltage is squared, yields 4x the output power from the same supply rail and load impedance (see equation 1). V (rms) + O(PP) 2 2 Power + V V (rms) 2 (1) RL POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION bridge-tied load versus single-ended mode (continued) VDD VO(PP) RL 2x VO(PP) VDD -VO(PP) Figure 48. Bridge-Tied Load Configuration In typical portable handheld equipment, a sound channel operating at 3.3 V and using bridging raises the power into an 8- speaker from a single-ended (SE, ground reference) limit of 62.5 mW to 250 mW. In terms of sound power that is a 6-dB improvement, which is loudness that can be heard. In addition to increased power there are frequency response concerns. Consider the single-supply SE configuration shown in Figure 49. A coupling capacitor is required to block the dc offset voltage from reaching the load. These capacitors can be quite large (approximately 33 F to 1000 F), tend to be expensive, heavy, and occupy valuable PCB area. These capacitors also have the additional drawback of limiting low-frequency performance of the system. This frequency limiting effect is due to the high-pass filter network created with the speaker impedance and the coupling capacitance and is calculated with equation 2. fc + 2 p R1 C (2) L C For example, a 68-F capacitor with an 8- speaker would attenuate low frequencies below 293 Hz. The BTL configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency performance is then limited only by the input network and speaker response. Cost and PCB space are also minimized by eliminating the bulky coupling capacitor. 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION bridge-tied load versus single-ended mode (continued) VDD -3 dB VO(PP) CC RL VO(PP) fc Figure 49. Single-Ended Configuration and Frequency Response Increasing power to the load does carry a penalty of increased internal power dissipation. The increased dissipation is understandable, considering that the BTL configuration produces 4x the output power of the SE configuration. Internal dissipation versus output power is discussed further in the thermal considerations section. BTL amplifier efficiency Linear amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD. The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal power dissipation of the amplifier. An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power supply to the power delivered to the load. To accurately calculate the RMS values of power in the load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 50). IDD VO IDD(RMS) V(LRMS) Figure 50. Voltage and Current Waveforms for BTL Amplifiers POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION BTL amplifier efficiency (continued) Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified shape whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different. Keep in mind that for most of the waveform, both the push and pull transistors are not on at the same time, which supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform. The following equations are the basis for calculating amplifier efficiency. Efficiency + PP L (3) SUP Where: PL V Lrms + V Lrms 2 RL 2 + 2R Vp L + V2P + VDD IDDrms + VDDp R2VP L 2V P I DDrms + pR P SUP L Efficiency of a BTL Configuration p VP + 2V DD + p P LR L 2 1 2 (4) 2V DD Table 1 employs equation 4 to calculate efficiencies for three different output power levels. The efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. The internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. Table 1. Efficiency Vs Output Power in 3.3-V 8- BTL Systems OUTPUT POWER (W) EFFICIENCY (%) PEAK-TO-PEAK VOLTAGE (V) INTERNAL DISSIPATION (W) 0.125 33.6 1.41 0.26 0.25 47.6 58.3 2.00 2.45 0.29 0.375 0.28 High-peak voltage values cause the THD to increase. A final point to remember about linear amplifiers (either SE or BTL) is how to manipulate the terms in the efficiency equation to utmost advantage when possible. In equation 4, VDD is in the denominator. This indicates that as VDD goes down, efficiency goes up. 22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION application schematic Figure 51 is a schematic diagram of a typical handheld audio application circuit, configured for a gain of -10 V/V. CF 5 pF Audio Input RF 50 k VDD 6 VDD VDD/2 RI 10 k CI 0.47 F 4 IN 2 BYPASS - VO+ 5 CC 330 F CS 1 F + 1 k CB 2.2 F - VO- 8 + From System Control 0.1 F 1 SHUTDOWN 3 SE/BTL 7 GND Bias Control 100 k VDD 100 k Figure 51. TPA311 Application Circuit The following sections discuss the selection of the components used in Figure 51. component selection gain setting resistors, RF and RI The gain for each audio input of the TPA311 is set by resistors RF and RI according to equation 5 for BTL mode. BTL Gain + AV + * 2 RF (5) RI BTL mode operation brings about the factor 2 in the gain equation due to the inverting amplifier mirroring the voltage swing across the load. Given that the TPA311 is a MOS amplifier, the input impedance is very high, consequently input leakage currents are not generally a concern, although noise in the circuit increases as the value of RF increases. In addition, a certain range of RF values is required for proper start-up operation of the amplifier. Taken together it is recommended that the effective impedance seen by the inverting node of the amplifier be set between 5 k and 20 k. The effective impedance is calculated in equation 6. Effective Impedance + RRF)RRI F (6) I POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION component selection (continued) As an example consider an input resistance of 10 k and a feedback resistor of 50 k. The BTL gain of the amplifier would be -10 V/V and the effective impedance at the inverting terminal would be 8.3 k, which is well within the recommended range. For high performance applications, metal film resistors are recommended because they tend to have lower noise levels than carbon resistors. For values of RF above 50 k the amplifier tends to become unstable due to a pole formed from RF and the inherent input capacitance of the MOS input structure. For this reason, a small compensation capacitor, CF, of approximately 5 pF should be placed in parallel with RF when RF is greater than 50 k. This, in effect, creates a low pass filter network with the cutoff frequency defined in equation 7. -3 dB f c(lowpass) + 2 p R1 C (7) F F fc For example, if RF is 100 k and CF is 5 pF then fc is 318 kHz, which is well outside of the audio range. input capacitor, CI In the typical application an input capacitor, CI, is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. In this case, CI and RI form a high-pass filter with the corner frequency determined in equation 8. -3 dB + 2 p R1 C f c(highpass) (8) I I fc The value of CI is important to consider as it directly affects the bass (low frequency) performance of the circuit. Consider the example where RI is 10 k and the specification calls for a flat bass response down to 40 Hz. Equation 8 is reconfigured as equation 9. CI 24 + 2 p 1R fc (9) I POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION component selection (continued) In this example, CI is 0.40 F, so one would likely choose a value in the range of 0.47 F to 1 F. A further consideration for this capacitor is the leakage path from the input source through the input network (RI, CI) and the feedback resistor (RF) to the load. This leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely higher than the source dc level. It is important to confirm the capacitor polarity in the application. power supply decoupling, CS The TPA311 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1 F placed as close as possible to the device VDD lead, works best. For filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 F or greater placed near the audio power amplifier is recommended. midrail bypass capacitor, CB The midrail bypass capacitor, CB, is the most critical capacitor and serves several important functions. During start-up or recovery from shutdown mode, CB determines the rate at which the amplifier starts up. The second function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and THD + N. The capacitor is fed from a 250-k source inside the amplifier. To keep the start-up pop as low as possible, the relationship shown in equation 10 should be maintained, which insures the input capacitor is fully charged before the bypass capacitor is fuly charged and the amplifier starts up. CB 10 250 k v RF ) RI CI 1 (10) As an example, consider a circuit where CB is 2.2 F, CI is 0.47 F, RF is 50 k and RI is 10 k. Inserting these values into the equation 10 we get: 18.2 35.5 which satisfies the rule. Bypass capacitor, CB, values of 0.1 F to 2.2 F ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance. single-ended operation In SE mode (see Figure 51), the load is driven from the primary amplifier output (VO+, terminal 5). In SE mode the gain is set by the RF and RI resistors and is shown in equation 11. Since the inverting amplifier is not used to mirror the voltage swing on the load, the factor of 2, from equation 5, is not included. SE Gain + AV + * RF (11) RI POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION single-ended operation (continued) The output coupling capacitor required in single-supply SE mode also places additional constraints on the selection of other components in the amplifier circuit. The rules described earlier still hold with the addition of the following relationship: CB 10 250 k v ) RI CI RLCC 1 RF 1 (12) As an example, consider a circuit where CB is 0.2.2 F, CI is 0.47 F, CC is 330 F, RF is 50 kRL is 32 , and RI is 10 k. Inserting these values into the equation 12 we get: 18.2 t 35.5 94.7 which satisfies the rule. output coupling capacitor, CC In the typical single-supply SE configuration, an output coupling capacitor (CC) is required to block the dc bias at the output of the amplifier, thus preventing dc currents in the load. As with the input coupling capacitor, the output coupling capacitor and impedance of the load form a high-pass filter governed by equation 13. -3 dB f c(high pass) + 2 p R1 C (13) L C fc The main disadvantage, from a performance standpoint, is that the typically small load impedances drive the low-frequency corner higher degrading the bass response. Large values of CC are required to pass low frequencies into the load. Consider the example where a CC of 330 F is chosen and loads vary from 8 , 32 , to 47 k. Table 2 summarizes the frequency response characteristics of each configuration. Table 2. Common Load Impedances vs Low Frequency Output Characteristics in SE Mode RL 8 CC 330 F LOWEST FREQUENCY 32 330 F 15 Hz 47,000 330 F 0.01 Hz 60 Hz As Table 2 indicates an 8- load is adequate, earphone response is good, and drive into line level inputs (a home stereo for example) is exceptional. 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION SE/BTL operation The ability of the TPA311 to easily switch between BTL and SE modes is one of its most important cost saving features. This feature eliminates the requirement for an additional earphone amplifier in applications where internal speakers are driven in BTL mode but external earphone or speaker must be accommodated. Internal to the TPA311, two separate amplifiers drive VO+ and VO-. The SE/BTL input (terminal 3) controls the operation of the follower amplifier that drives VO- (terminal 8). When SE/BTL is held low, the amplifier is on and the TPA311 is in the BTL mode. When SE/BTL is held high, the VO- amplifier is in a high output impedance state, which configures the TPA311 as an SE driver from VO+ (terminal 5). IDD is reduced by approximately one-half in SE mode. Control of the SE/BTL input can be from a logic-level TTL source or, more typically, from a resistor divider network as shown in Figure 52. 4 IN 2 BYPASS - VO+ 5 + 1 k - VO- 8 + 0.1 F 1 SHUTDOWN 3 SE/BTL CC 330 F 7 GND Bias Control 100 k VDD 100 k Figure 52. TPA311 Resistor Divider Network Circuit Using a readily available 1/8-in. (3.5 mm) mono earphone jack, the control switch is closed when no plug is inserted. When closed the 100-k/1-k divider pulls the SE/BTL input low. When a plug is inserted, the 1-k resistor is disconnected and the SE/BTL input is pulled high. When the input goes high, the VO- amplifier is shutdown causing the BTL speaker to mute (virtually open-circuits the speaker). The VO+ amplifier then drives through the output capacitor (CC ) into the earphone jack. using low-ESR capacitors Low-ESR capacitors are recommended throughout this application. A real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the real capacitor behaves like an ideal capacitor. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION 5-V versus 3.3-V operation The TPA311 operates over a supply range of 2.5 V to 5.5 V. This data sheet provides full specifications for 5-V and 3.3-V operation, as these are considered to be the two most common standard voltages. There are no special considerations for 3.3-V versus 5-V operation with respect to supply bypassing, gain setting, or stability. The most important consideration is that of output power. Each amplifier in TPA311 can produce a maximum voltage swing of VDD - 1 V. This means, for 3.3-V operation, clipping starts to occur when VO(PP) = 2.3 V as opposed to VO(PP) = 4 V at 5 V. The reduced voltage swing subsequently reduces maximum output power into an 8- load before distortion becomes significant. Operation from 3.3-V supplies, as can be shown from the efficiency formula in equation 4, consumes approximately two-thirds the supply power for a given output-power level of operation from 5-V supplies. headroom and thermal considerations Linear power amplifiers dissipate a significant amount of heat in the package under normal operating conditions. A typical music CD requires 12 dB to 15 dB of dynamic headroom to pass the loudest portions without distortion as compared with the average power output. From the TPA311 data sheet, one can see that when the TPA311 is operating from a 5-V supply into a 8- speaker that 350 mW peaks are available. Converting watts to dB: P dB + 10 Log PW P ref + 10 Log 3501 WmW + - 4.6 dB Subtracting the headroom restriction to obtain the average listening level without distortion yields: * 15 dB + * 19.6 dB (15 dB headroom) - 4.6 dB * 12 dB + * 16.6 dB (12 dB headroom) - 4.6 dB * 9 dB + * 13.6 dB (9 dB headroom) - 4.6 dB * 6 dB + * 10.6 dB (6 dB headroom) - 4.6 dB * 3 dB + * 7.6 dB (3 dB headroom) - 4.6 dB Converting dB back into watts: PW 28 + 10PdB10 Pref + 11 mW (15 dB headroom) + 22 mW (12 dB headroom) + 44 mW (9 dB headroom) + 88 mW (6 dB headroom) + 175 mW (3 dB headroom) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 APPLICATION INFORMATION headroom and thermal considerations (continued) This is valuable information to consider when attempting to estimate the heat dissipation requirements for the amplifier system. Comparing the absolute worst case, which is 350 mW of continuous power output with 0 dB of headroom, against 12 dB and 15 dB applications drastically affects maximum ambient temperature ratings for the system. Using the power dissipation curves for a 5-V, 8- system, the internal dissipation in the TPA311 and maximum ambient temperatures is shown in Table 3. Table 3. TPA311 Power Rating, 5-V, 8-, BTL MAXIMUM AMBIENT TEMPERATURE AVERAGE OUTPUT POWER POWER DISSIPATION (mW) 0 CFM SOIC 350 350 mW 600 46C 114C 350 175 mW (3 dB) 500 64C 120C 350 88 mW (6 dB) 380 85C 125C 350 44 mW (9 dB) 300 98C 125C 350 22 mW (12 dB) 200 115C 125C 350 11 mW (15 dB) 180 119C 125C PEAK OUTPUT POWER (mW) 0 CFM DGN Table 3 shows that the TPA311 can be used to its full 350-mW rating without any heat sinking in still air up to 46C. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 29 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 MECHANICAL DATA D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0.050 (1,27) 0.020 (0,51) 0.014 (0,35) 14 0.010 (0,25) M 8 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 0.010 (0,25) 1 7 0- 8 A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) PINS ** 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047 / D 10/96 NOTES: A. B. C. D. 30 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TPA311 350-mW MONO AUDIO POWER AMPLIFIER SLOS207B - JANUARY 1998 - REVISED MARCH 2000 MECHANICAL DATA DGN (S-PDSO-G8) PowerPAD PLASTIC SMALL-OUTLINE PACKAGE 0,38 0,25 0,65 8 0,25 M 5 Thermal Pad (See Note D) 0,15 NOM 3,05 2,95 4,98 4,78 Gage Plane 0,25 1 0- 6 4 3,05 2,95 0,69 0,41 Seating Plane 1,07 MAX 0,15 0,05 0,10 4073271/A 04/98 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions include mold flash or protrusions. The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad. This pad is electrically and thermally connected to the backside of the die and possibly selected leads. E. Falls within JEDEC MO-187 PowerPAD is a trademark of Texas Instruments. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 31 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated