TD62707AP TOSHIBA BIPOLAR DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC TD62707AP 4CH HIGH-VOLTAGE SOURCE DRIVER WITH ENABLE The TD62707AP is comprised of four source current output stages and enable inputs which can gate the outputs. All outputs feature integral clamp diodes for switching inductive loads. Applications include relay, hammer and lamp drivers. FEATURES High output voltage VCC-VOUT = 50 V MIN. Output current (single output) IOUT = -750 mA MIN. Input compatible with TTL, 5 V CMOS Output clamp diodes Enable inputs E1, E2 GND terminal = HEAT SINK Weight: 1.11 g (Typ.) Package type : DIP-16 pin PIN CONNECTION (TOP VIEW) SCHEMATICS (EACH DRIVER) Note: The output parasitic diodes cannot be used as clamp diodes. 1 2001-07-05 TD62707AP TRUTH TABLE E1 E2 IN1~4 OUT1~4 H H H OFF H L H ON L H H OFF H H L OFF L L H OFF L L L OFF H L L OFF MAXIMUM RATINGS (Ta = 25C) CHARACTERISTIC SYMBOL RATING UNIT Supply Voltage VCC 50 V Output Voltage VOUT -50 V Output Current IOUT -0.75 A / ch VIN1 -0.5~15 VIN2 (Note 1) -0.5~VCC Clamp Diode Reverse Voltage VR 50 V Clamp Diode Forward Current IF -0.75 A Power Dissipation PD 1.47 / 2.7 (Note 2) W Operating Temperature Topr -40~85 C Storage Temperature Tstg -55~150 C Input Voltage V Note 1: VCC 15 V Note 2: On PCB (50 x 50 x 1.6 mm Cu 50%) RECOMMENDED OPERATING CONDITIONS (Ta = -40~85C) CHARACTERISTIC SYMBOL CONDITION MIN Supply Voltage VCC 50 V Output Voltage VOUT 0 -50 V DC 1 Circuits, Ta = 25C 0 -600 Output Current IOUT (Note) Tpw = 25 ms, 4 Circuits Duty = 10 % Ta = 85C, Tj = 120C Duty = 50 % 0 -600 0 -160 0 15 VIN Input Voltage "H" level "L" level TYP. MAX VIH1 VCC > 15 V 2.0 15 VIH2 VCC 15 V 2.0 VCC UNIT mA / ch V VIL 0 0.8 Clamp Diode Reverse Voltage VR 50 V Clamp Diode Forward Current IF 600 mA Power Dissipation PD 1.2 W Note: Ta = 85C (Note) On PCB (50 x 50 x 1.6 mm Cu 50%) 2 2001-07-05 TD62707AP ELECTRICAL CHARACTERISTICS (Ta = 25C unless otherwise noted VCC = 50 V, "H" = VIH, "L" = VIL) CHARACTERISTIC Input Voltage SYMBOL TEST CIR- CUIT TEST CONDITION 1 MIN TYP. MAX 2.0 0.8 VIN = H 70 100 VE1 = H 0 10 E2 VE2 = H 66 100 IN VIN = L -40 -100 VE1 = L -20 -50 VE2 = H -40 -100 "H" level VIH "L" level VIL IN Input Current Input Current "H" level "L" level E1 E1 IIH IIL 4 5 E2 Output Leakage Current UNIT V A A IOL 2 VCC = 50 V, OUTPUT OFF 100 ICCH 4 VIN = H, VE1 = H VE2 = L, OUTPUT OPEN 5.5 7.0 ICCL 5 VIN = L, VE1 = H VE2 = L, OUTPUT OFF 5.5 7.0 VOH 3 VIN = H, VE1 = "H" VE2 = L, IOUT = -500 mA VCC -2.5 VCC -2.0 V Clamp Diode Reverse Current IR 6 VR = 50 V 100 A Clamp Diode Forward Voltage VF 7 IF = 500 mA 1.5 2.0 V Turn-On Delay tON 0.5 tOFF VCE = 50 V, RL = 83 Turn-Off Delay 8 6.0 Supply Current Output Voltage "H" level A mA s TEST CIRCUIT 1. VIH, VIL 2. IOL 3. VOH 4. IIH, ICCH 5. IIL, ICCL 6. IR 3 2001-07-05 TD62707AP 7. VF 8. tON, tOFF Note 1: Pulse Width 50 s, Duty Cycle 10% Output Impedance 50 , tr 5 ns, tf 10 ns Note 2: VIH = 3 V, E1 = VIH, E2 = GND, VCC = 50 V Note 3: CL includes probe and jig capacitance PRECAUTIONS for USING This IC does not integrate protection circuits such as overcurrent and overvoltage protectors. Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that excess current or voltage will not be applied to the IC. Utmost care is necessary in the design of the output line, VCC and GND line since IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. 4 2001-07-05 TD62707AP 5 2001-07-05 TD62707AP 6 2001-07-05 TD62707AP PACKAGE DIMENSIONS DIP16-P-300-2.54A Unit: mm Weight: 1.11 g (Typ.) 7 2001-07-05 TD62707AP RESTRICTIONS ON PRODUCT USE 000707EBA * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice. 8 2001-07-05