LM20242 36V, 2A PowerWise(R) Adjustable Frequency Synchronous Buck Regulator General Description Features The LM20242 is a full featured 1MHz capable synchronous buck regulator capable of delivering up to 2A of load current. The current mode control loop is externally compensated with only two external components, offering both high performance and ease of use. The device is optimized to work over the input voltage range of 4.5V to 36V making it well suited for high voltage systems. The device features internal Over Voltage Protection (OVP) and Over Current Protection (OCP) circuits for increased system reliability. A precision Enable pin and integrated UVLO allows the turn on of the device to be tightly controlled and sequenced. Startup inrush currents are limited by both an internally fixed and externally adjustable soft-start circuit. Fault detection and supply sequencing are possible with the integrated PGOOD circuit. The LM20242 is designed to work well in multi-rail power supply architectures. The output voltage of the device can be configured to track a higher voltage rail using the SS/TRK pin. If the output of the LM20242 is pre-biased at startup it will not sink current to pull the output low until the internal soft-start ramp exceeds the voltage at the feedback pin. The LM20242 is offered in an exposed pad 20 pin TSSOP package that can be soldered to the PCB, eliminating the need for bulky heatsinks. 2A Output Current, 3.7A peak current 130 m/110 m integrated power MOSFETs 1.5% output voltage accuracy Current Mode Control, selectable compensation Resistor programmed, 1MHz capable oscillator Synchronous rectifier with diode emulation Adjustable output voltage down to 0.8V Compatible with pre-biased loads Programmable soft-start with external capacitor Precision enable pin with hysteresis OVP, UVLO inputs and PGOOD output Internally protected with peak current limit, thermal shutdown and restart Accurate current limit with frequency foldback Non-linear current mode slope compensation eTSSOP-20 exposed pad package Applications Simple to design, high efficiency point of load regulation from a 4.5V to 36V bus High Performance DSPs, FPGAs, ASICs and Microprocessors Communications Infrastructure, Automotive Simplified Application Circuit 30031401 PowerWise(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300314 www.national.com LM20242 36V, 2A PowerWise(R) Adjustable Frequency Synchronous Buck Regulator May 29, 2008 LM20242 Connection Diagram 30031402 Top View eTSSOP-20 Package Ordering Information Order Number Package Type NSC Package Drawing Package Marking Supplied As LM20242MH eTSSOP-20 MXA20A 20242MH 73 Units per Rail LM20242MHE 250 Units per Tape and Reel LM20242MHX 2500 Units per Tape and Reel Pin Descriptions Pin(s) Name 1 SS/TRK Description Application Information Soft-Start or Tracking control input An internal 5 A current source charges an external capacitor to set the soft-start rate. The PWM can Track to an external voltage ramp with a low impedance source. If left open, an internal 1 ms SS ramp is activated. 2 FB Feedback input to the error amplifier from the regulated output This pin is connected to the inverting input of the internal transconductance error amplifier. An 800 mV reference is internally connected to the non-inverting input of the error amplifier. 3 PGOOD Power good output signal Open drain output indicating the output voltage is regulating within tolerance. A pull-up resistor of 10 k to 100 k is recommended if this function is used. 4 COMP 5,6,15,16 VIN Input supply voltage Nominal operating range: 4.5V to 36V. 7,8,13,14 SW Switch pin The drain terminal of the internal Synchronous Rectifier power NMOSFET and the source terminal of the internal Control power NMOSFET. Output of the internal error amplifier and The loop compensation network should be connected between the input to the Pulse Width Modulator COMP pin and the AGND pin. 9,10,11 GND Ground Internal reference for the power MOSFETs. 12 AGND Analog ground Internal reference for the regulator control functions. 17 BOOT Boost input for bootstrap capacitor An internal diode from VCC to BOOT charges an external capacitor required from SW to BOOT to power the Control MOSFET gate driver. 18 VCC 19 EN Enable or UVLO input 20 RT Internal oscillator frequency adjust input Normally biased at 550 mV. An external resistor connected between RT and AGND sets the internal oscillator frequency. EP Output of the high voltage linear VCC tracks VIN up to about 7.2V. Above VIN = 7.2V, VCC is regulated regulator. The VCC voltage is regulated to approximately 5.5 Volts. A 0.1 F to 1 F ceramic decoupling to approximately 5.5V. capacitor is required. The VCC pin is an output only. Exposed Exposed pad Pad www.national.com An external voltage divider can be used to set the line undervoltage lockout threshold. If the EN pin is left unconnected, a 2 A pull-up current source pulls the EN pin high to enable the regulator. Exposed metal pad on the underside of the package with a weak electrical connection to GND. Connect this pad to the PC board ground plane in order to improve heat dissipation. 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND BOOT to GND BOOT to SW SW to GND SW to GND (Transient) FB, EN, SS/TRK, PGOOD to GND -0.3V to +38V -0.3V to +43V -0.3V to +7V -0.5V to +38V -1.5V (< 20 ns) -0.3V to +6V -0.3V to +8V -65C to 150C 2kV Operating Ratings VIN to GND Junction Temperature +4.5V to +36V -40C to + 125C Electrical Characteristics Unless otherwise stated, the following conditions apply: VVIN = 12V. Limits in standard type are for TJ = 25C only, limits in bold face type apply over the junction temperature (TJ) range of -40C to +125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Symbol Parameter Conditions Feedback pin voltage VVIN = 4.5V to 36V VCOMP = 500 mV to 700 mV RHSW-DS(ON) High-Side MOSFET On-Resistance RLSW-DS(ON) Low-Side MOSFET On-Resistance IQ Operating Quiescent Current VVIN = 4.5V to 36V ISD Shutdown Quiescent current VEN = 0V VUVLO VIN Under Voltage Lockout Rising VVIN VFB VUVLO(HYS) VVCC ISS IBOOT VF-BOOT Min Typ Max Units 0.788 0.8 0.812 V ISW = 200 mA 130 225 m ISW = 200 mA 110 190 m 2 3 mA 150 180 A 3.65 VIN Under Voltage Lockout Hysteresis 3.9 4.2 V 200 400 mV 7 A VCC Voltage IVCC = -5 mA, VEN = 5V Soft-Start Pin Source Current VSS = 0V 5.5 BOOT Diode Leakage VBOOT = 4V 10 BOOT Diode Forward Voltage IBOOT = -100 mA 0.9 1.1 V Over Voltage Protection Rising Threshold VFB(OVP) / VFB 107 110 112 % Over Voltage Protection Hysteresis VFB(OVP) / VFB 2 3 % PGOOD Rising Threshold VFB(PG) / VFB 93 95 97 % PGOOD Hysteresis VFB(PG) / VFB 2 3 % 3 5 V nA Powergood VFB(OVP) VFB(OVP-HYS) VFB(PG) VFB(PG-HYS) TPGOOD PGOOD delay IPGOOD(SNK) PGOOD Low Sink Current VPGOOD = 0.5V IPGOOD(SRC) PGOOD High Leakage Current VPGOOD = 5V FSW1 Switching Frequency 1 RRT = 49.9 k FSW2 Switching Frequency 2 RRT = 249 k DMAX Maximum Duty Cycle 0.6 20 s 1 mA 5 200 nA 675 750 825 kHz 225 250 325 kHz Oscillator ILOAD = 0A 90 % RT pin voltage RRT = 250 k 550 mV Feedback pin bias current VFB = 1V 50 nA ICOMP(SRC) COMP Output Source Current VFB = 0V VCOMP = 0V 200 400 A ICOMP(SNK) COMP Output Sink Current VFB = 1V VCOMP = 0.5V 200 350 A Error Amplifier DC Transconductance ICOMP = -50 A to +50 A 400 515 AVOL Error Amplifier Voltage Gain COMP pin open 2000 V/V GBW Error Amplifier Gain-Bandwidth Product COMP pin open 7 MHz VRT Error Amplifier IFB gm 3 600 mho www.national.com LM20242 VCC to GND Storage Temperature ESD Rating Human Body Model (Note 2) Absolute Maximum Ratings (Note 1) LM20242 Symbol Parameter Conditions Min Typ Max Units 3.1 3.7 4.65 A Current Limit ILIM Cycle By Cycle Current Limit TILIM Cycle By Cycle Current Limit Delay 150 ns Enable VEN(RISING) EN Pin Rising Threshold VEN(HYS) EN Pin Hysteresis IEN EN Source Current 1.2 1.25 1.3 V 50 mV 2 A Thermal Shutdown 170 C Thermal Shutdown Hysteresis 20 C 5.6 C/W 30 C/W VEN = 0V, VVIN = 12V Thermal Shutdown TSD TSD(HYS) Thermal Resistance JC Junction to Case JA Junction to Ambient 0 LFM airflow Note 1: Absolute Maximum Ratings indicate limits beyond witch damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor to each pin. Note 3: Min and Max limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National's Average Outgoing Quality Level (AOQL). Typical Performance Characteristics Unless otherwise specified: TJ = 25C, VVIN = 12V Efficiency vs. Load Current fSW = 350 kHz, VOUT = 3.3V Efficiency vs. Load Current fSW = 500 kHz, VOUT = 3.3V 30031403 www.national.com 30031404 4 LM20242 Error Amplifier Gain Error Amplifier Phase 30031405 30031406 Line Regulation VCC vs. VIN 30031407 30031408 Non-Switching IQ vs. VIN Shutdown IQ vs. VIN 30031409 30031410 5 www.national.com LM20242 PGOOD VOL vs. IPGOOD EN Threshold and Hysteresis vs. Temperature 30031421 30031419 EN Current vs. Temperature Oscillator Frequency vs. RRT 30031422 30031453 Oscillator Frequency vs. VIN High-Side FET Resistance vs. Temperature 30031455 30031454 www.national.com 6 Low-Side FET Resistance vs. Temperature 30031456 30031457 Peak Current Limit vs. Temperature Startup with CSS = 0 30031459 30031458 Startup with CSS = 200 nF 30031460 7 www.national.com LM20242 Load Transient Response LM20242 Block Diagram 30031423 www.national.com 8 GENERAL The LM20242 switching regulator features all of the functions necessary to implement an efficient low voltage buck regulator using a minimum number of external components. This easy to use regulator features two integrated switches and is capable of supplying up to 2A of continuous output current. The regulator utilizes peak current mode control with nonlinear slope compensation to optimize stability and transient response over the entire output voltage range. Peak current mode control also provides inherent line feed-forward, cycleby-cycle current limiting and easy loop compensation. The switching frequency can be varied from 100 kHz to 1 MHz with an external resistor to ground. The device can operate at high switching frequency allowing use of a small inductor while still achieving efficiencies as high as 93%. The precision internal voltage reference allows the output to be set as low as 0.8V. Fault protection features include: current limiting, thermal shutdown, over voltage protection, and shutdown capability. The device is available in the eTSSOP-20 package featuring an exposed pad to aid thermal dissipation. The typical application circuit for the LM20242 is shown in Figure 2 in the design guide. SOFT-START AND VOLTAGE TRACKING The SS/TRK pin is a dual function pin that can be used to set the startup time or track an external voltage source. The startup or soft-start time can be adjusted by connecting a capacitor from the SS/TRK pin to ground. The soft-start feature allows the regulator output to gradually reach the steady state operating point, thus reducing stresses on the input supply and controlling startup current. If no soft-start capacitor is used the device defaults to the internal soft-start circuitry resulting in a startup time of approximately 1 ms. For applications that require a monotonic startup or utilize the PGOOD pin, an external soft-start capacitor is recommended. The SS/TRK pin can also be set to track an external voltage source. The tracking behavior can be adjusted by two external resistors connected to the SS/TRK pin as shown in Figure 7. in the design guide. PRE-BIAS STARTUP CAPABILITY The LM20242 is in a pre-biased state when it starts up with an output voltage greater than zero. This often occurs in many multi-rail applications such as when powering an FPGA, ASIC, or DSP. In these applications the output can be prebiased through parasitic conduction paths from one supply rail to another. Even though the LM20242 is a synchronous converter, it will not pull the output low when a pre-bias condition exists. During start up the LM20242 will not sink current until the soft-start voltage exceeds the voltage on the FB pin. Since the device cannot sink current, it protects the load from damage that might otherwise occur if current is conducted through the parasitic paths of the load. PRECISION ENABLE The enable (EN) pin allows the output of the device to be enabled or disabled with an external control signal. This pin is a precision analog input that enables the device when the voltage exceeds 1.25V (typical). The EN pin has 50 mV of hysteresis and will disable the output when the enable voltage falls below 1.2V (typical). If the EN pin is not used, it should be disconnected so the internal 2 A pull-up will default this function to the enabled condition. Since the enable pin has a precise turn-on threshold it can be used along with an external resistor divider network from VIN to configure the device to turn-on at a precise input voltage. The precision enable circuitry will remain active even when the device is disabled. POWER GOOD AND OVER VOLTAGE FAULT HANDLING The LM20242 has built in under and over voltage comparators that control the power switches. Whenever there is an excursion in output voltage above the set OVP threshold, the part will terminate the present on-pulse, turn-on the low-side FET, and pull the PGOOD pin low. The low-side FET will remain on until either the FB voltage falls back into regulation or the zero cross detection is triggered which in turn tri-states the FETs. If the output reaches the UVP threshold the part will continue switching and the PGOOD pin will be deasserted and go low. Typical values for the PGOOD resistor are on the order of 100 k or less. To avoid false tripping during transient glitches the PGOOD pin has 20 s of built in deglitch time to both rising and falling edges. PEAK CURRENT MODE CONTROL In most cases, the peak current mode control architecture used in the LM20242 only requires two external components to achieve a stable design. The compensation can be selected to accommodate any capacitor type or value. The external compensation also allows the user to set the crossover frequency and optimize the transient performance of the device. For duty cycles above 50% all current mode control buck converters require the addition of an artificial ramp to avoid sub-harmonic oscillation. This artificial linear ramp is commonly referred to as slope compensation. What makes the LM20242 unique is the amount of slope compensation will change depending on the output voltage. When operating at high output voltages the device will have more slope compensation than when operating at lower output voltages. This is accomplished in the LM20242 by using a non-linear parabolic ramp for the slope compensation. The parabolic slope compensation of the LM20242 is much better than the traditional linear slope compensation because it optimizes the stability of the device over the entire output voltage range. UVLO The LM20242 has an internal under-voltage lockout protection circuit that keeps the device from switching until the input voltage reaches 3.9V (typical). The UVLO threshold has 200 mV of hysteresis that keeps the device from responding to power-on glitches during start up. If desired the turn-on point of the supply can be changed by using the precision enable pin and a resistor divider network connected to VIN as shown in Figure 6 in the design guide. CURRENT LIMIT The precise current limit enables the device to operate with smaller inductors that have lower saturation currents. When the peak inductor current reaches the current limit threshold, an over current event is triggered and the internal high-side FET turns off and the low-side FET turns on, allowing the inductor current to ramp down until the next switching cycle. For THERMAL PROTECTION Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated, typically at 170C, the 9 www.national.com LM20242 each sequential over-current event, the reference voltage is decremented and PWM pulses are skipped resulting in a current limit that does not aggressively fold back for brief overcurrent events, while at the same time providing frequency and voltage foldback protection during hard short circuit conditions. Operation Description LM20242 LM20242 tri-states the power FETs and resets soft-start. After the junction cools to approximately 150C, the part starts up using the normal start up routine. This feature is provided to prevent catastrophic failures from accidental device overheating. Several diagrams are shown in Figure 1 illustrating continuous conduction mode (CCM), discontinuous conduction mode, and the boundary condition. It can be seen that in diode emulation mode, whenever the inductor current reaches zero the SW node will become high impedance. Ringing will occur on this pin as a result of the LC tank circuit formed by the inductor and the parasitic capacitance. If this ringing is of concern, an additional RC snubber circuit can be added from the switch node to ground. At very light loads, usually below 100 mA, several pulses may be skipped in between switching cycles, effectively reducing the switching frequency and further improving light-load efficiency. LIGHT LOAD OPERATION The LM20242 offers increased efficiency when operating at light loads. Whenever the load current is reduced to a point where the peak to peak inductor ripple current is greater than two times the load current, the part will enter the diode emulation mode preventing significant negative inductor current. The point at which this occurs is the critical conduction boundary and can be calculated by the following equation: 30031464 FIGURE 1. Modes of Operation for LM20242 www.national.com 10 This section walks the designer through the steps necessary to select the external components to build a fully functional power supply. As with any DC-DC converter numerous tradeoffs are possible to optimize the design for efficiency, size, or 30031429 FIGURE 2. Typical Application Circuit The first equation to calculate for any buck converter is dutycycle. Ignoring conduction losses associated with the FETs and parasitic resistances it can be approximated by: INDUCTOR SELECTION (L) The inductor value is determined based on the operating frequency, load current, ripple current and duty cycle. The inductor selected should have a saturation current rating greater than the peak current limit of the device. Keep in mind the specified current limit does not account for delay of the current limit comparator, therefore the current limit in the application may be higher than the specified value. To optimize the performance and prevent the device from entering current limit at maximum load, the inductance is typically selected such that the ripple current, iL, is not greater than 30% of the rated output current. Figure 3 illustrates the switch and inductor ripple current waveforms. Once the input voltage, output voltage, operating frequency and desired ripple current are known, the minimum value for the inductor can be calculated by the formula shown below: 30031467 FIGURE 3. Switch and Inductor Current Waveforms If needed, slightly smaller value inductors can be used, however, the peak inductor current, IOUT + iL/2, should be kept below the peak current limit of the device. In general, the inductor ripple current, iL, should be more than 10% of the rated output current to provide adequate current sense information for the current mode control loop. If the ripple current in the inductor is too low, the control loop will not have sufficient current sense information and can be prone to instability. OUTPUT CAPACITOR SELECTION (COUT) The output capacitor, COUT, filters the inductor ripple current and provides a source of charge for transient load conditions. A wide range of output capacitors may be used with the LM20242 that provide excellent performance. The best performance is typically obtained using ceramic, SP or OSCON type chemistries. Typical trade-offs are that the ceramic capacitor provides extremely low ESR to reduce the output ripple voltage and noise spikes, while the SP and OSCON capacitors provide a large bulk capacitance in a small volume for transient loading conditions. When selecting the value for the output capacitor, the two performance characteristics to consider are the output volt11 www.national.com LM20242 performance. These will be taken into account and highlighted throughout this discussion. To facilitate component selection discussions the circuit shown in Figure 2 below may be used as a reference. Unless otherwise indicated all formulas assume units of amps (A) for current, farads (F) for capacitance, henries (H) for inductance and volts (V) for voltages. Design Guide LM20242 age ripple and transient response. The output voltage ripple can be approximated by using the following formula. SETTING THE OUTPUT VOLTAGE (RFB1, RFB2) The resistors RFB1 and RFB2 are selected to set the output voltage for the device. Table 1 provides suggestions for RFB1 and RFB2 for common output voltages. TABLE 1. Suggested Values for RFB1 and RFB2 Where, VOUT (V) is the amount of peak to peak voltage ripple at the power supply output, RESR () is the series resistance of the output capacitor, fSW(Hz) is the switching frequency, and COUT (F) is the output capacitance used in the design. The amount of output ripple that can be tolerated is application specific; however a general recommendation is to keep the output ripple less than 1% of the rated output voltage. Keep in mind ceramic capacitors are sometimes preferred because they have very low ESR; however, depending on package and voltage rating of the capacitor the value of the capacitance can drop significantly with applied voltage. The output capacitor selection will also affect the output voltage droop during a load transient. The peak droop on the output voltage during a load transient is dependent on many factors; however, an approximation of the transient droop ignoring loop bandwidth can be obtained using the following equation. RFB2(k) VOUT short open 0.8 4.99 10 1.2 8.87 10.2 1.5 12.7 10.2 1.8 21.5 10.2 2.5 31.6 10.2 3.3 If different output voltages are required, RFB2 should be selected to be between 4.99 k to 49.9 k and RFB1 can be calculated using the equation below. ADJUSTING THE OPERATING FREQUENCY (RRT) The operating frequency of the LM20242 can be adjusted by connecting a resistor from the RT pin to ground. The equation shown below can be used to calculate the value of RRT for a given operating frequency. Where, COUT (F) is the minimum required output capacitance, L (H) is the value of the inductor, VDROOP (V) is the output voltage drop ignoring loop bandwidth considerations, IOUTSTEP (A) is the load step change, RESR () is the output capacitor ESR, VIN (V) is the input voltage, and VOUT (V) is the set regulator output voltage. Both the tolerance and voltage coefficient of the capacitor should be examined when designing for a specific output ripple or transient droop target. Where, fSW is the switching frequency in kHz, and RRT is the frequency adjust resistor in k. Please refer to the curve Oscillator Frequency versus RRT in the typical performance characteristics section. If the RRT resistor is omitted the device will not operate. INPUT CAPACITOR SELECTION Good quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during the on-time. In general it is recommended to use a ceramic capacitor for the input as they provide both a low impedance and small footprint. One important note is to use a good dielectric for the ceramic capacitor such as X5R or X7R. These provide better over temperature performance and also minimize the DC voltage derating that occurs on Y5V capacitors. The input capacitors should be placed as close as possible to the VIN and GND pins on both sides of the device. Non-ceramic input capacitors should be selected for RMS current rating and minimum ripple voltage. A good approximation for the required ripple current rating is given by the relationship: LOOP COMPENSATION (RC1, CC1) The purpose of loop compensation is to meet static and dynamic performance requirements while maintaining adequate stability. Optimal loop compensation depends on the output capacitor, inductor, load and the device itself. The overall loop transfer function is the product of the power stage and the feedback network transfer functions. For stability purposes, the objective is to have a loop gain slope that is -20db/decade from a very low frequency to beyond the crossover frequency. Figure 4 shows the transfer functions for power stage, feedback/compensation network, and the resulting closed loop system for the LM20242. As indicated by the RMS ripple current equation, highest requirement for RMS current rating occurs at 50% duty cycle. For this case, the RMS ripple current rating of the input capacitor should be greater than half the output current. For best performance, low ESR ceramic capacitors should be placed in parallel with higher capacitance capacitors to provide the best input filtering for the device. www.national.com RFB1(k) 12 If needed, the value for CC2 should be calculated using the equation shown below. 30031472 FIGURE 4. LM20242 Loop Compensation Where RESR is the output capacitor series resistance and RC1 is the calculated compensation resistance. The power stage transfer function is dictated by the modulator, output LC filter, and load; while the feedback transfer function is set by the feedback resistor ratio, error amp gain and external compensation network. To achieve a -20dB/decade slope, the error amplifier zero, located at fZ(EA), should be positioned to cancel the output filter pole (fP(FIL)). An additional error amp pole, located at fP2 (EA), can be added to cancel the output filter zero at fZ(FIL). Cancellation of the output filter zero is recommended if larger value, non-ceramic output capacitors are used. Compensation of the LM20242 is achieved by adding an RC network as shown in Figure 5 below. BOOT CAPACITOR (CBOOT) The LM20242 integrates an N-Channel buck switch and associated floating high voltage level shift / gate driver. This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.1 F ceramic capacitor, connected with short traces between the BOOT pin and SW pin, is recommended. During the off-time of the buck switch, the SW pin voltage is approximately 0V and the bootstrap capacitor is charged from VCC through the internal bootstrap diode. SUB-REGULATOR BYPASS CAPACITOR (CVCC) The capacitor at the VCC pin provides noise filtering for the internal sub-regulator. The recommended value of CVCC should be no smaller than 0.1 F and no greater than 1 F. The capacitor should be a good quality ceramic X5R or X7R capacitor. In general, a 1 F ceramic capacitor is recommended for most applications. The VCC regulator should not be used for other functions since it isn't protected against short circuit. SETTING THE START UP TIME (CSS) The addition of a capacitor connected from the SS pin to ground sets the time at which the output voltage will reach the final regulated value. Larger values for CSS will result in longer start up times. Table 3, shown below provides a list of soft start capacitors and the corresponding typical start up times. 30031445 FIGURE 5. Compensation Network for LM20242 A good starting value for CC1 for most applications is 4.7 nF. Once the value of CC1 is chosen the value of RC should be calculated using the equation below to cancel the output filter pole (fP(FIL)) as shown in Figure 4. TABLE 2. Start Up Times for Different Soft-Start Capacitors 13 Start Up Time (ms) CSS (nF) 1 none 5 33 10 68 15 100 20 120 www.national.com LM20242 A higher crossover frequency can be obtained, usually at the expense of phase margin, by lowering the value of CC1 and recalculating the value of RC1. Likewise, increasing CC1 and recalculating RC1 will provide additional phase margin at a lower crossover frequency. As with any attempt to compensate the LM20242 the stability of the system should be verified for desired transient droop and settling time. If the output filter zero, fZ(FIL) approaches the crossover frequency (FC), an additional capacitor (CC2) should be placed at the COMP pin to ground. This capacitor adds a pole to cancel the output filter zero assuring the crossover frequency will occur before the double pole at fSW/2 degrades the phase margin. The output filter zero is set by the output capacitor value and ESR as shown in the equation below. LM20242 If different start up times are needed the equation shown below can be used to calculate the start up time. TRACKING AN EXTERNAL SUPPLY By using a properly chosen resistor divider network connected to the SS/TRK pin, as shown in Figure 7, the output of the LM20242 can be configured to track an external voltage source to obtain a simultaneous or ratiometric start up. As shown above, the start up time is influenced by the value of the soft-start capacitor CSS(F) and the 5 A soft-start pin current ISS(A). that may be found in the electrical characteristics table. While the soft-start capacitor can be sized to meet many start up requirements, there are limitations to its size. The soft-start time can never be faster than 1 ms due to the internal default 1 ms start up time. When the device is enabled there is an approximate time interval of 50 s when the soft-start capacitor will be discharged just prior to the soft-start ramp. If the enable pin is rapidly pulsed or the soft-start capacitor is large there may not be enough time for CSS to completely discharge resulting in start up times less than predicted. To aid in discharging of soft-start capacitor during long disable periods an external 1M resistor from SS/TRK to ground can be used without greatly affecting the start up time. 30031461 FIGURE 7. Tracking an External Supply Since the soft-start charging current ISS is always present on the SS/TRK pin, the size of R2 should be less than 10 k to minimize the errors in the tracking output. Once a value for R2 is selected the value for R1 can be calculated using appropriate equation in Figure 8, to give the desired start up. Figure 8 shows two common start up sequences; the top waveform shows a simultaneous start up while the waveform at the bottom illustrates a ratiometric start up. USING PRECISION ENABLE AND POWER GOOD The precision enable (EN) and power good (PGOOD) pins of the LM20242 can be used to address many sequencing requirements. The turn-on of the LM20242 can be controlled with the precision enable pin by using two external resistors as shown in Figure 6 . 30031462 FIGURE 6. Sequencing LM20242 with Precision Enable The value for resistor RB can be selected by the user to control the current through the divider. Typically this resistor will be selected to be between 10 k and 1 M. Once the value for RB is chosen the resistor RA can be solved using the equation below to set the desired turn-on voltage. 30031478 When designing for a specific turn-on threshold (VTO) the tolerance on the input supply, enable threshold (VIH_EN), and external resistors need to be considered to insure proper turnon of the device. The LM20242 features an open drain power good (PGOOD) pin to sequence external supplies or loads and to provide fault detection. This pin requires an external resistor (RPG) to pull PGOOD high when the output is within the PGOOD tolerance window. Typical values for this resistor range from 10 k to 100 k. www.national.com FIGURE 8. Common Start Up Sequences A simultaneous start up is preferred when powering most FPGAs, DSPs, or other microprocessors. In these systems the higher voltage, VOUT1, usually powers the I/O, and the lower voltage, VOUT2, powers the core. A simultaneous start up provides a more robust power up for these applications since it avoids turning on any parasitic conduction paths that may exist between the core and the I/O pins of the processor. 14 of thermal shutdown. If thermal shutdown occurs it is a sign of inadequate heatsinking or excessive power dissipation in the device. PCB LAYOUT CONSIDERATIONS PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DCDC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability. Good layout can be implemented by following a few simple design rules. 1. Minimize area of switched current loops. In a buck regulator there are two loops where currents are switched very fast. The first loop starts from the input capacitor, to the regulator VIN pin, to the regulator SW pin, to the inductor then out to the output capacitor and load. The second loop starts from the output capacitor ground, to the regulator GND pins, to the inductor and then out to the load (see Figure 9). To minimize both loop areas the input capacitor should be placed as close as possible to the VIN pin. Grounding for both the input and output capacitor should consist of a small localized top side plane that connects to GND and the exposed pad (EP). The inductor should be placed as close as possible to the SW pin and output capacitor. 2. Minimize the copper area of the switch node. Since the LM20242 has the SW pins on opposite sides of the package it is recommended that the SW pins should be connected with a trace that runs around the package. The inductor should be placed at an equal distance from the SW pins using 100 mil wide traces to minimize capacitive and conductive losses. 3. Have a single point ground for all device grounds located under the EP. The ground connections for the compensation, feedback, and soft-start components should be connected together then routed to the EP pin of the device. The AGND pin should connect to GND under the EP. If not properly handled poor grounding can result in degraded load regulation or erratic switching behavior. 4. Minimize trace length to the FB pin. Since the feedback node can be high impedance the trace from the output resistor divider to FB pin should be as short as possible. This is most important when high value resistors are used to set the output voltage. The feedback trace should be routed away from the SW pin and inductor to avoid contaminating the feedback signal with switch noise. 5. Make input and output bus connections as wide as possible. This reduces any voltage drops on the input or output of the converter and can improve efficiency. Voltage accuracy at the load is important so make sure feedback voltage sense is made at the load. Doing so will correct for voltage drops at the load and provide the best output accuracy. 6. Provide adequate device heatsinking. Use as many vias as is possible to connect the EP to the power plane heatsink. For best results use a 5x3 via array with a minimum via diameter of 12 mils. "Via tenting" with the solder mask may be necessary to prevent wicking of the solder paste applied to the EP. See the Thermal Considerations section to insure enough copper heatsinking area is used to keep the junction temperature below 125C. BENEFIT OF AN EXTERNAL SCHOTTKY During dead time, the body diode of the synchronous MOSFET acts as a free-wheeling diode and conducts the inductor current. The MOSFET is optimized for high breakdown voltage, but this makes an inefficient body diode reverse recovery charge. The power loss is proportional to load current and switching frequency. The loss increases at higher input voltages and switching frequencies. One simple solution is to use a small 1A external Schottky diode between SW and GND as shown in Figure 10, diodes D1 and D2. The external Schottky diode effectively conducts all inductor current during the dead time, minimizing the current passing through the synchronous MOSFET body diode and eliminating reverse recovery losses. The external Schottky conducts currents for a very small portion of the switching cycle, therefore the average current is low. An external Schottky rated for 1A will improve efficiency by several percent in some applications. A Schottky rated at a higher current will not significantly improve efficiency and may be worse due to the increased reverse capacitance. The forward voltage of the synchronous MOSFET body diode is approximately 700 mV, therefore an external Schottky with a forward voltage less than or equal to 700 mV should be selected to ensure the majority of the dead time current is carried by the Schottky. THERMAL CONSIDERATIONS The thermal characteristics of the LM20242 are specified using the parameter JA, which relates the junction temperature to the ambient temperature. Although the value of JA is dependant on many variables, it still can be used to approximate the operating junction temperature of the device. To obtain an estimate of the device junction temperature, one may use the following relationship: TJ = PD x JA + TA and PD = PIN x (1 - Efficiency) - 1.1 x (IOUT)2 x DCR Where: TJ is the junction temperature in C. PIN is the input power in Watts (PIN = VIN x IIN). JA is the junction to ambient thermal resistance for the LM20242. TA is the ambient temperature in C. IOUT is the output load current. DCR is the inductor series resistance. It is important to always keep the operating junction temperature (TJ) below 125C for reliable operation. If the junction temperature exceeds 160C the device will cycle in and out 15 www.national.com LM20242 The second most common power on behavior is known as a ratiometric start up. This start up is preferred in applications where both supplies need to be at the final value at the same time. Similar to the soft-start function, the fastest start up possible is 1ms regardless of the rise time of the tracking voltage. When using the track feature the final voltage seen by the SS/ TRACK pin should exceed 1V to provide sufficient overdrive and transient immunity. LM20242 30031446 FIGURE 9. Schematic of LM20242 Highlighting Layout Sensitive Nodes 30031444 FIGURE 10. Typical Application Schematic www.national.com 16 ID Qty Part Number Size Description Vendor U1 1 LM20242MH eTSSOP-20 IC, Switching Regulator NSC L1 1 MSS1260-153MX MSS1260 15 H, 4.6A ISAT Coilcraft C1-3 3 GRM32ER71H475KA88L 1210 4.7 F, 50V, X7R Murata C4, 6, 9 3 VJ0805JY104KXX 0805 0.1 F Vishay C5, 11 2 VJ0805Y105JXACW1BC 0805 1 F Vishay C7 1 C1608COG1H121J 0603 120 pF TDK C8 1 VJ0805Y222J 0805 2.2 nF Vishay C10 1 C1210C107M9PAC 1210 100 F Kemet D1, D2 2 MBR0540 SOD123 0.5A, 40V, Schottky Fairchild R1,9 2 CRCW06031002F 0603 10 k Vishay R2 1 CRCW08052053F 0805 205 k Vishay R3 1 CRCW08051212F 0805 12.1 k Vishay R4, 7 2 CRCW060330000ZOEA 0603 0 k Vishay R5 1 CRCW08053212F 0805 32.1 k Vishay R6 1 CRCW08051022F 0805 10.2 k Vishay R8 1 CRCW08054992F 0603 49.9 k Vishay 17 www.national.com LM20242 Bill of Materials LM20242 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead eTSSOP Package NS Package Number MXA20A www.national.com 18 LM20242 Notes 19 www.national.com LM20242 36V, 2A PowerWise(R) Adjustable Frequency Synchronous Buck Regulator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com