ASP-109262-01 125 - SAMTEC

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 1Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Pulse Proof Thick Film Chip Resistors

FEATURES

• High pulse performance, up to 10 kW

• Stability R/R  1 % for 1000 h at 70 °C

• AEC-Q200 qualified

• Material categorization: for definitions of

compliance please see www.vishay.com/doc?99912

Notes

• These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and

permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally

known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time.

• Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020).

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.

Note

(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.

STANDARD ELECTRICAL SPECIFICATIONS

TYPE

CASE

SIZE

IMPERIAL

CASE

SIZE

METRIC

POWER

RATING

P70

LIMITING

ELEMENT

VOLTAGE

Umax.

ACRMS/DC

TEMPERATURE

COEFFICIENT

ppm/K

TOLERANCE

RESISTANCE

RANGE



SERIES

D10/CRCW0402-IF 0402 RR1005M 0.063 50 ± 200 ± 5 1.0 to 100K E24

± 10

D11/CRCW0603-IF 0603 RR1608M 0.10 75 ± 200 ± 5 1.0 to 100K E24

± 10

D12/CRCW0805-IF 0805 RR2012M 0.125 150 ± 200 ± 5 1.0 to 100K E24

± 10

D25/CRCW1206-IF 1206 RR3216M 0.25 200 ± 200 ± 5 1.0 to 100K E24

± 10

CRCW1210-IF 1210 RR3225M 0.50 200 ± 200 ± 5 1.0 to 100K E24

± 10

CRCW2010-IF 2010 RR5025M 0.75 400 ± 200 ± 5 1.0 to 100K E24

± 10

CRCW2512-IF 2512 RR6332M 1.0 500 ± 200 ± 5 1.0 to 100K E24

± 10

TECHNICAL SPECIFICATIONS

PARAMETER UNIT D10/

CRCW0402-IF

D11/

CRCW0603-IF

D12/

CRCW0805-IF

D25/

CRCW1206-IF CRCW1210-IF CRCW2010-IF CRCW2512-IF

Rated dissipation



(1)

W 0.063 0.1 0.125 0.25 0.5 0.75 1.0

Operating voltage



max.

RMS

/DC V 50 75 150 200 200 400 500

Insulation voltage



ins

(1 min) V 75 100 200 300 300 300 300

Insulation resistance



> 10

Operating temperature



range °C -55 to +155

Failure rate h

-1

< 0.1 x 10

-9

Mass mg 0.65 2 5.5 10 16 25.5 40.5

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 2Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PART NUMBER AND PRODUCT DESCRIPTION

Part Number: CRCW08051R00JNEAIF

TYPE

VALUE

TOLERANCE TCR PACKAGING SPECIAL

CRCW0402

CRCW0603

CRCW0805

CRCW1206

CRCW1210

CRCW2010

CRCW2512

R = Decimal

K = Thousand

J = ± 5 %

K = ± 10 %

N = ± 200 ppm/K EA, EB,

EC, ED,

EE, EF,

EG, EH,

EI, EL

Up to 2 digits

IF = Pulse proof

Product Description: D12/CRCW0805-IF 200 1R0 5 % ET1 e3

D12/CRCW0805-IF 200 1R0 5 % ET1 e3

TYPE TCR

RESISTANCE VALUE

TOLERANCE PACKAGING LEAD (Pb)-FREE

D10/CRCW0402-IF

D11/CRCW0603-IF

D12/CRCW0805-IF

D25/CRCW1206-IF

CRCW1210-IF

CRCW2010-IF

CRCW2512-IF

± 200 ppm/K 1R0 = 1 

10K = 10 k

± 5 %

± 10 %

ET1, ET2,

ET3, ET4,

ET5, ET6,

ET7, ET8,

ET9, EF4,

E02, E67,

E82

e3 = Pure tin

termination finish

PACKAGING

TYPE CODE QUANTITY CARRIER TAPE WIDTH PITCH REEL DIAMETER

D10/CRCW0402-IF ED = ET7 10 000

Paper tape acc. to

IEC 60286-3

Type 1a

8 mm 2 mm 180 mm/7"

EE = EF4 50 000 330 mm/13"

D11/CRCW0603-IF

EI = ET2 5000

8 mm 2 mm

180 mm/7"

ED = ET3 10 000 180 mm/7"

EL = ET4 20 000 285 mm/11.25"

EE = ET8 50 000 330 mm/13"

EA = ET1 5000

8 mm 4 mm

180 mm/7"

EB = ET5 10 000 285 mm/11.25"

EC = ET6 20 000 330 mm/13"

D12/CRCW0805-IF

EA = ET1 5000

8 mm 4 mm

180 mm/7"

EB = ET5 10 000 285 mm/11.25"

EC = ET6 20 000 330 mm/13"

D25/CRCW1206-IF

EA = ET1 5000

8 mm 4 mm

180 mm/7"

EB = ET5 10 000 285 mm/11.25"

EC = ET6 20 000 330 mm/13"

CRCW1210-IF

EA = ET1 5000

8 mm 4 mm

180 mm/7"

EB = ET5 10 000 285 mm/11.25"

EC = ET6 20 000 330 mm/13"

CRCW2010-IF EF = E02 4000 Pressed tape

acc. to

IEC 60286-3

Type 1b

12 mm 4 mm 180 mm/7"

CRCW2512-IF EG = E67 2000 12 mm 8 mm 180 mm/7"

EH = E82 4000 4 mm

CW08051R00 N A FCR JEI

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 3Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

FUNCTIONAL PERFORMANCE

DIMENSIONS in millimeters

SIZE DIMENSIONS

RECOMMENDED SOLDER PAD

DIMENSIONS

REFLOW

SOLDERING

WAVE

SOLDERING

IMPERIAL METRIC L W H T1 T2 a b l a b l

0402 RR1005M 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5

0603 RR1608M 1.55 + 0.10

- 0.05 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0

0805 RR2012M 2.0 + 0.20

- 0.10 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.20

- 0.10 0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3

1206 RR3216M 3.2 + 0.10

- 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3

1210 RR3225M 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2

2010 RR5025M 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9

2512 RR6332M 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2

0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100

Maximum pulse load, single pulse; applicable if P 0 and n ≤ 1000 and Û ≤ Ûmax.;

for permissible resistance change equivalent to 8000 h operation

Pulse Duration (s)

Pulse Power (W)

0.1

0.01

100

1000

100 000

2512

2010

1210

1206

0805

0603

0402

10 000

Maximum pulse dissipation as a function of the pulse duration,

single pulse

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 4Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100

Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑ

amb

) and Û ≤ Û

max.

;

for permissible resistance change equivalent to 8000 h operation

Pulse Duration (s)

Pulse Power (W)

0.1

0.01

100

1000

100 000

2512

2010

1210

1206

0805

0603

0402

10 000

Maximum pulse dissipation as a function of the pulse duration,

continuous pulse loading

2000

200

10- 6 10- 5 10- 4 10- 3 10- 2 10- 1 110

Maximum pulse voltage, single and continuous pulses; applicable if

P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation

Pulse Duration i (s)

400

600

800

1000

1200

1400

1600

1800

Pulse Voltage max. (V)

2512

1206/1210

0805 0603

0402

2010

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 5Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

1 10 100 1000 10 000 100 000

10 000

100

1000

2512

2010

1210

1206

0805

0603

0402

Resistance Value (Ω)

Peak Voltage (V)

Pulse load rating in accordance to EN 60115-1, 4.27; 1.2 μs/50 μs;

5 pulses at 12 s intervals; for permissible resistance change 1 %

Single-pulse high voltage overload test 1.2 µs/50 µs EN 140000 4.27

1 10 100 1000 10 000 100 000

Resistance Value (Ω)

Peak Voltage (V)

10 000

100

1000

Pulse load rating in accordance to EN 60115-1, 4.27; 10 μs/700 μs;

10 pulses at 1 min intervals; for permissible resistance change 1 %

Single-pulse high voltage overload test 10 µs/700 µs EN 140000 4.27

2512

2010

1210

1206

0805

0603

0402

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 6Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TEST PROCEDURES AND REQUIREMENTS

60115-1

CLAUSE

IEC

60082-2

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS PERMISSIBLE

CHANGE (R)

STABILITY CLASS 1 OR BETTER

Stability for product type: 1  to 100 k

D/CRCW-IF e3

4.5 - Resistance - ± 5 %; ± 10 %

4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown

4.13 - Short time overload U = 2.5 x  2 x Umax.;

duration acc. to style ± (0.25 % R + 0.05 )

4.17.2 58 (Td) Solderability

Solder bath method;

Sn60Pb40;

non-activated flux;

(235 ± 5) °C, (2 ± 0.2) s

Good tinning ( 95 % covered);

no visible damage

Solder bath method;

Sn96.5Ag3Cu0.5;

non-activated flux;

(245 ± 5) °C, (3 ± 0.3) s

Good tinning ( 95 % covered);

no visible damage

4.8.4.2 - Temperature coefficient (20/- 55/20) °C and

(20/125/20) °C ± 200 ppm/K

4.19 14 (Na) Rapid change of temperature

30 min. at - 55 °C;

30 min. at 125°C

5 cycles

1000 cycles

± (0.25 % R + 0.05 )

± (1 % R + 0.05 )

- 50 0 50 100 150

Ambient Temperature

amb (°C)

Fraction of Rated Dissipation P70 (%)

100

Derating

P70 x R

D/CRCW-IF e3

www.vishay.com Vishay

Revision: 17-Mar-15 7Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

All tests are carried out in accordance with the following specifications:

• EN 60115-1, generic specification

• EN 140400, sectional specification

• EN 140401-802, detail specification

• IEC 60068-2-x, environmental test procedures

Packaging of components is done in paper or blister tapes according to IEC 60286-3.

4.23 - Climatic sequence: -

± (1 % R + 0.05 )

4.23.2 2 (Ba) Dry heat 125 °C; 16 h

4.23.3 30 (Db) Damp heat, cyclic 55 °C;  90 % RH;

24 h; 1 cycle

4.23.4 1 (Aa) Cold - 55 °C; 2 h

4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h

4.23.6 30 (Db) Damp heat, cyclic 55 °C;  90 % RH;

24 h; 5 cycles

4.23.7 - DC load U =

4.25.1 - Endurance at 70 °C

U =  Umax.

1.5 h on; 0.5 h off;

70 °C; 1000 h

70 °C; 8000 h

± (1 % R + 0.05 )

± (2 % R + 0.1 )

4.18.2 58 (Td) Resistance to soldering heat Solder bath method

(260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 )

4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C;

(93 ± 3) % RH; 56 days ± (1 % R + 0.05 )

4.25.3 - Endurance at upper

category temperature 155 °C; 1000 h ± (1 % R + 0.05 )

4.27 - Single pulse high voltage

overload, 10 μs/700 μs

Û = 10 x  2 x Umax.;

10 pulses ± (1 % R + 0.05 )

TEST PROCEDURES AND REQUIREMENTS

60115-1

CLAUSE

IEC

60082-2

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS PERMISSIBLE

CHANGE (R)

STABILITY CLASS 1 OR BETTER

Stability for product type: 1  to 100 k

D/CRCW-IF e3

P70 x R

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 08-Feb-17 1Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.