TFT COLOR LCD MODULE NL6448BC33-53 26cm (10.4 Type) VGA PRELIMINARY DATA SHEET (2nd edition) All information is subject to change without notice. Please confirm the delivery specification before starting to design your system. Document Number: DOD-M- 1309 (2nd edition) Published date: January 2003 CP(N) 1 a NEC Corporation 2003 All rights reserved. NL6448BC33-53 INTRODUCTION No part of this document shall be copied in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product described herein or any other liability arising from use of such application. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or of others. While NEC Corporation has been making continuous effort to enhance the reliability of its products, the possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to person arising from a failure in an NEC product, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. NEC products are classified into the following three quality grades: "Standard", "Special", "Specific" The "Specific" quality grade applies only to applications developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a product depend on its quality grade, as indicated below. Customers must check the quality grade of each application before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems (medical equipment, etc.) and any other equipment The quality grade of this product is "Standard" unless otherwise specified in this document. If customers intend to use this product for applications other than those specified for "Standard" quality grade, they should contact NEC Corporation sales representative in advance. Anti-radioactive design is not implemented in this product. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 2 NL6448BC33-53 CONTENTS INTRODUCTION ..........................................................................................................................................2 1. OUTLINE....................................................................................................................................................4 1.1 STRUCTURE AND PRINCIPLE...........................................................................................................4 1.2 APPLICATIONS.....................................................................................................................................4 1.3 FEATURES.............................................................................................................................................4 2. GENERAL SPECIFICATIONS ................................................................................................................5 3. BLOCK DIAGRAM ...................................................................................................................................6 4. DETAILED SPECIFICATIONS ...............................................................................................................7 4.1 MECHANICAL SPECIFICATIONS......................................................................................................7 4.2 ABSOLUTE MAXIMUM RATINGS ....................................................................................................7 4.3 ELECTRICAL CHARACTERISTICS...................................................................................................8 4.3.1 Driving for LCD panel signal processing board ............................................................................8 4.3.2 Working for backlight lamp ...........................................................................................................9 4.3.3 Power supply voltage ripple.........................................................................................................10 4.3.4 Fuse..............................................................................................................................................10 4.4 POWER SUPPLY VOLTAGE SEQUENCE ........................................................................................ 11 4.4.1 Sequence for LCD panel signal processing board ....................................................................... 11 4.4.2 Sequence for backlight inverter (Option)..................................................................................... 11 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS.........................................................12 4.5.1 LCD panel signal processing board .............................................................................................12 4.5.2 Backlight lamp.............................................................................................................................13 4.5.3 Positions of plug and a socket......................................................................................................13 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS ..........................................................................14 4.7 DISPLAY POSITIONS.........................................................................................................................15 4.8 SCANNING DIRECTIONS .................................................................................................................15 4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD ...........................16 4.9.1 Outline of input signal timings ....................................................................................................16 4.9.2 Timing characteristics ..................................................................................................................17 4.9.3 Input signal timing chart ..............................................................................................................19 4.10 OPTICS...............................................................................................................................................22 4.10.1 Optical characteristics................................................................................................................22 4.10.2 Definition of contrast ratio.........................................................................................................23 4.10.3 Definition of luminance uniformity ...........................................................................................23 4.10.4 Definition of response times ......................................................................................................23 4.10.5 Definition of viewing angles......................................................................................................23 5. RELIABILITY TESTS.............................................................................................................................24 6. PRECAUTIONS .......................................................................................................................................25 6.1 MEANING OF CAUTION SIGNS ......................................................................................................25 6.2 CAUTIONS ..........................................................................................................................................25 6.3 ATTENTIONS ......................................................................................................................................25 6.3.1 Handling of the product ...............................................................................................................25 6.3.2 Environment.................................................................................................................................26 6.3.3 Characteristics..............................................................................................................................26 6.3.4 Other ............................................................................................................................................26 7. OUTLINE DRAWINGS ...........................................................................................................................27 7.1 FRONT VIEW ......................................................................................................................................27 7.2 REAR VIEW ........................................................................................................................................28 REVISION HISTORY .................................................................................................................................29 PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 3 NL6448BC33-53 1. OUTLINE 1.1 STRUCTURE AND PRINCIPLE NL6448BC33-53 module is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass substrate and a color-filter glass substrate. Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual TFT arrays. The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through the TFT array of red, green and blue dots. 1.2 APPLICATIONS * Display terminal for control system * Industrial PC 1.3 FEATURES * Ultra-wide viewing angle * High luminance * High contrast * 6-bit digital RGB signals * Reversible-scan direction * Edge light type * Replaceable lamp for backlight (Inverter less) PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 4 NL6448BC33-53 2. GENERAL SPECIFICATIONS Display area 211.2 (W) x 158.4 (H) mm (typ.) Diagonal size of display 26 cm (10.4 inches) Drive system a-Si TFT active matrix Display color 262,144 colors Pixel 640 (H) x 480 (V) pixels Pixel arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe Dot pitch 0.11 (W) x 0.33 (H) mm Pixel pitch 0.33 (W) x 0.33 (H) mm Module size 243.0 (W) x 185.1 (H) x 10.5 (D) mm (typ.) Weight 475 g (typ.) Contrast ratio 300:1 (typ.) Viewing angle At the contrast ratio 10:1 * Horizontal: Right side 85 (typ.), Left side 85 (typ.) * Vertical: Up side 85 (typ.), Down side 85 (typ.) Designed viewing direction At DPS= Low or open: normal scan * Viewing angle with optimum grayscale (=2.2): normal axis Polarizer surface Clear Polarizer pencil-hardness 3H (min.) [by JIS K5400] Color gamut At LCD panel center 40 % (typ.) [against NTSC color space] Response time Ton (black 10% white 90%) 24 ms (typ.) Luminance At 5.0mArms / lamp 350 cd/m2 (typ.) Signal system 6-bit digital signals for data of RGB colors, Dot clock (CLK), Data enable (DE), Horizontal synchronous signal (Hsync), Vertical synchronous signal (Vsync) Power supply voltage LCD panel signal processing board: 3.3V or 5.0V Backlight Edge light type: 2 cold cathode fluorescent lamps Power consumption 2 2 Replaceable parts * Lamp holder set: Type No. 104LHS39 2 Recommended inverter (Option) * Inverter: Type No. 104PW191, 104PW161 2 At 5.0mArms / lamp and checkered flag pattern 6.2 W (typ.) PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 2 5 NL6448BC33-53 3. BLOCK DIAGRAM Host LCD module (Product) 100 H-driver R0 to R5 100 G0 to G5 100 B0 to B5 100 Hsync 1,920 lines 100 V-driver 100 DE 47k 480 lines Vsync Controller 100 CLK LCD panel H: 640 x 3 (R,G,B) V: 480 DPS 8.2k Power supply for gradation GND Note1 Note2 VCC Fuse FG Note1 Note2 DC/DC converter LCD panel signal processing board Backlight (Edge light type) VBLH VDDB GNDB Note1 Note2 Backlight inverter (Option) Lamp Lamp VBLH VBLC Note1 Metallic frame of lamp holder Note1: Connections between GND (Signal ground), FG (Frame ground) and VBLC (Lamp low voltage terminal) in the LCD module GND - FG Not connected GND - VBLC Not connected FG - VBLC Not connected Note2: These grounds should be connected together in customer equipment. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 6 NL6448BC33-53 4. DETAILED SPECIFICATIONS 4.1 MECHANICAL SPECIFICATIONS Parameter Specification Unit Module size 243.0 0.5 (W) x 185.1 0.5 (H) x 10.5 0.5 (D) Note1 mm Display area 211.2 (W) x 158.4 (H) Note1 mm Weight 475 (typ.), 500 (max.) g 2 Note1: See "7. OUTLINE DRAWINGS". 4.2 ABSOLUTE MAXIMUM RATINGS Parameter Power supply voltage Symbol Rating Unit LCD panel signal board VCC -0.3 to +6.5 V Lamp voltage Note1 VBLH 1,500 Vrms Display signals Note2 VD -0.3 to VCC+0.3 V Function signals Note3 VF -0.3 to VCC+0.3 V Tst -20 to +80 C - Front surface TopF -10 to +70 C Note4 Rear surface TopR TBD C Note5 95 % Ta 40C 85 % 40 < Ta 50C 70 Note7 g/m3 Input voltage for signals Storage temperature Remarks Ta = 25C Operating temperature Relative humidity Note6 RH Absolute humidity Note6 AH Ta > 50C Note1: "VBLH" is the voltage value between low voltage terminal (Cold) and high voltage terminal (Hot). Note2: Display signals are CLK, Hsync, Vsync, DE and DATA (R0 to R5, G0 to G5, B0 to B5). Note3: Function signal is DPS. Note4: Measured at center of LCD panel surface (including self-heat) Note5: Measured at center of LCD module's rear shield surface (including self-heat) Note6: No condensation Note7: Ta = 50C, RH = 85% PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 7 NL6448BC33-53 4.3 ELECTRICAL CHARACTERISTICS 4.3.1 Driving for LCD panel signal processing board (Ta = 25C) Parameter Symbol Power supply voltage VCC Min. Typ. Max. Unit Remarks 3.0 3.3 3.6 V for 3.3V system 4.75 5.0 5.25 V for 5V system 280 Note1 200 Note1 400 Note2 280 Note2 mA VCC = 3.3V 2 mA VCC = 5.0V 2 Power supply current ICC - Logic input voltage for display signals Low VDL 0 - 0.3Vcc V High VDH 0.7Vcc - Vcc V Low VFL 0 - 0.3Vcc V High VFH 0.7Vcc - Vcc V CMOS level Input voltage for DPS signal Note1: Checkered flag pattern [by EIAJ ED-2522] Note2: Pattern for maximum current PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 8 NL6448BC33-53 4.3.2 Working for backlight lamp (Ta=25C Note1) Parameter Symbol Min. Typ. Max. Unit Lamp current IBL 2.0 5.0 5.5 mArms Lamp voltage VBLH - 520 - Vrms 850 - - Vrms TBD - - Vrms 50 - 70 kHz Lamp starting voltage Oscillation frequency VS FO Remarks at IBL=5.0mArms: 350cd/m2 Note3 Note2, Note3 Ta = 25C Note2, Note3 Ta = -10C Note2, Note3 Note4 2 Note1: This product's backlight consists of 2 lamps, and these specifications are for each lamp. Note2: The lamp voltage cycle between lamps should be kept on a same phase. "VS" and "VBLH" are the voltage value between low voltage side (Cold) and high voltage side (Hot). Note3: The asymmetric ratio of working waveform for lamps (Power supply voltage peak ratio, power supply current peak ratio and waveform space ratio) should be less than 5 % (See the following figure.). If the waveform is asymmetric, DC (Direct current) element apply into the lamp. In this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (Cold terminal) and high voltage terminal (Hot terminal). Pa - Pb x 100 5 % Pb Pa Sa 0 Pb Sb Sa - Sb x 100 5 % Sb Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative Sa: Waveform space for positive part, Sb: Waveform space for negative part Note4: In case "FO" is not the recommended value, beat noise may display on the screen, because of interference between "FO" and "1/th". Recommended value of "FO" is as following. 1 1 x (2n-1) x FO = th 4 th: Horizontal cycle (See "4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD".) n: Natural number (1, 2, 3 ) Note5: Method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. When design the backlight inverter, evaluate the fluctuation of lamp current and voltage or asymmetric of lamp working waveform sufficiently. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 9 NL6448BC33-53 4.3.3 Power supply voltage ripple This product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. Parameter Power supply voltage Ripple voltage Note1 (Measure at input terminal of power supply) Unit 3.3 V 100 mVp-p 5.0 V 100 mVp-p VCC Note1: The permissible ripple voltage includes spike noise. 4.3.4 Fuse Parameter Fuse Type Supplier TBD TBD Rating Fusing current Remarks TBD Note1 TBD VCC TBD Note1: The power supply capacity should be more than the fusing current. If the power supply capacity is less than the fusing current, the fuse may not blow for a short time, and then nasty smell, smoking and so on may occur. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 10 NL6448BC33-53 4.4 POWER SUPPLY VOLTAGE SEQUENCE 4.4.1 Sequence for LCD panel signal processing board OFF ON 3.0V or 4.75V VCC Note1 0V Toff > 50ms Tr < 30ms Display and function signals Note2 VALID period 0ms < t < 35ms 0ms < t < 35ms Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V in "VCC = 3.3V" or 4.75V in "VCC = 5.0V", a protection circuit may work, and then this product may not work. Note2: Display (CLK, Hsync, Vsync, DE, R0 to R5, G0 to G5, B0 to B5) and function (DPS) signals must be Low or High-impedance, exclude the VALID period (See above sequence diagram), in order to avoid that internal circuits is damaged. If some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. If customer stops the display and function signals, they should be cut VCC. 4.4.2 Sequence for backlight inverter (Option) Note2 Display and function signals Note1 VALID period VDDB Note1: These are the display and function signals for LCD panel signal processing board. Note2: The backlight inverter voltage (VDDB) should be inputted within the valid period of display and function signals, in order to avoid unstable data display. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 11 NL6448BC33-53 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS 4.5.1 LCD panel signal processing board CN1 socket (LCD module side): DF9C-31P-1V (Hirose Electric Co., Ltd.) Adaptable plug: DF9-31S-1V (Hirose Electric Co., Ltd.) Pin No. Symbol Signal 1 GND Ground 2 CLK Dot clock 3 Hsync Horizontal synchronous 4 Vsync Vertical synchronous 5 GND Ground 6 R0 Red data (LSB) 7 R1 Red data 8 R2 Red data 9 R3 Red data 10 R4 Red data 11 R5 Red data (MSB) 12 GND Ground - 13 G0 Green data (LSB) Least significant bit 14 G1 Green data 15 G2 Green data 16 G3 Green data 17 G4 Green data 18 G5 Green data (MSB) Most significant bit 19 GND Ground - 20 B0 Blue data (LSB) Least significant bit 21 B1 Blue data 22 B2 Blue data 23 B3 Blue data 24 B4 Blue data 25 B5 Blue data (MSB) 26 GND Ground 27 DE Selection of DE / Fixed mode 28 VCC Power supply 29 VCC Power supply 30 NC Non connection 31 DPS Selection of scan direction Remarks - Least significant bit - Most significant bit - - Most significant bit Data enable signal: DE mode High or Open: Fixed mode Note1 High: Reverse scan Low or Open: Normal scan Note1 Note1: See "4.7 DISPLAY POSITIONS AND SCANNING DIRECTIONS". PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 12 NL6448BC33-53 4.5.2 Backlight lamp Attention: VBLH and VBLC must be connected correctly. If customer connects wrongly, customer will be hurt and the module will be broken. CN2 plug: Adaptable socket: BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) SM03 (4.0) B-BHS-TB (J.S.T Mfg. Co., Ltd.) Pin No. Symbol Signal Remarks 1 VBLC Low voltage (Cold) Cable color: Gray 2 VBLH High voltage (Hot) Cable color: White 3 VBLH High voltage (Hot) Cable color: White 4.5.3 Positions of plug and a socket Low voltage (Cold) CN2 1 3 Rear side Caution label High voltage (Hot) 1 3 2 30 31 CN1 Barcode label PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) Name plate 13 NL6448BC33-53 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS This product can display in equivalent to 262,144 colors in 64 scale. Also the relation between display colors and input data signals is as the following table. Data signal (0: Low level, 1: High level) Display colors Basic colors Red scale Black Blue Red Magenta Green Cyan Yellow White Black dark bright Red Black Green scale dark bright Green Black Blue scale dark bright Blue R 5 R 4 R 3 R 2 R 1 R 0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 1 1 1 0 1 : : 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : 0 0 0 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 1 1 1 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 14 NL6448BC33-53 4.7 DISPLAY POSITIONS The following table is the coordinates per pixel (See "4.8 SCANNING DIRECTIONS".). C (0, 0 ) R G B C( 0, 0) C( 1, 0) *** C( X, 0) *** C(638, 0) C(639, 0) C( 0, 1) C( 1, 1) *** C( X, 1) *** C(638, 1) C(639, 1) * * * * * * * *** * * * * * *** * * * * * *** * C( 0, Y) C( 1, Y) *** C( X, Y) *** C(638, Y) C(639, Y) * * * * * * * *** * * * * * *** * * * * * * * C( 0, 478) C( 1, 478) *** C( X, 478) *** C(638, 478) C(639, 478) C( 0, 479) C( 1, 479) *** C( X, 479) *** C(638, 479) C(639, 479) 4.8 SCANNING DIRECTIONS The following figures are seen from a front view. Also the arrow shows the direction of scan. C (0,0) C (639,0) D (0,0) D (639,0) Note1 C (0,479) C (639,479) D (0,479) D (639,479) Figure 1. Normal scan (DPS: Low or Open) C (0,0) C (639,0) D (639,479) D (0,479) Note1 C (0,479) C (639,479) D (639,0) D (0,0) Figure 2. Reverse scan (DPS: High) Note1: Meaning of C (X, Y) and D (X, Y) C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".) D (X, Y): The data number of input signal for LCD panel signal processing board PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 15 NL6448BC33-53 4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD 4.9.1 Outline of input signal timings This diagram indicates virtual signal for set up to timing. * Horizontal signal Horizontal synchronizing cycle (th) Horizontal synchronizing pulse width (thp) Hsync Note1 Horizontal back-porch (thb) Horizontal front-porch (thf) Display period Horizontal display period (thd) DE (Data enable) Note1: Fixed mode cannot be used while working of DE mode. Note2: This diagram indicates virtual signal for set up to timing. * Vertical signal Vertical synchronizing cycle (tv) Vertical synchronizing pulse width (tvp) Vsync Note1 Vertical back-porch (tvb) Vertical front-porch (tvf) Display period Note2 Vertical display period (tvd) DE (Data enable) 1 2 3 4 480 Note3 Note1: Fixed mode cannot be used while working of DE mode. Note2: This diagram indicates virtual signal for set up to timing. Note3: See "4.9.3 Input signal timing chart" for numeration of pulse. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 16 NL6448BC33-53 4.9.2 Timing characteristics (a) Fixed mode (Note1) Parameter Symbol Min. Typ. Max. Unit Remarks Frequency 1/tc 21.0 25.2 29.0 MHz 39.7 ns (typ.) Duty tcd 0.4 0.5 0.6 - Rise time, Fall time tcrf - - 10 ns Setup time tds 8 - - ns Hold time tdh 12 - - ns Rise time, Fall time tdrf - - 10 ns Cycle th 30.0 31.8 33.6 Display period CLK DATA (R0-R5) (G0-G5) (B0-B5) Hsync CLK-DATA CLK thd 640 CLK Front-porch thf 16 CLK Pulse width thp 10 96 - CLK Back-porch thb - 48 134 CLK Total of pulse width and back-porch thp + thb 144 31.4 kHz (typ.) Note2 CLK Setup time ths 8 - - ns Hold time thh 12 - - ns Rise time, Fall time thrf - - 10 ns Cycle tv 16.1 16.7 17.2 ms Display period tvd 480 H Front-porch tvf 12 H Pulse width tvp 1 - 2 H Back-porch tvb 31 - 32 H Total of pulse width and back-porch tvp + tvb Hsync- Vsync thv 1 - Vsync-Hsync tvh 30 Rise time, Fall time tvrf - CLK- Hsync Vsync s 800 - 525 - 59.9 Hz (typ.) H 33 Note2 H - CLK - - ns - 10 ns - Note1: Definition of parameters is as follows. tc = 1CLK, tcd = tch/tc, th = 1H Note2: Keep tvp + tvb and thp + thb within the table. If it is out of specification, display position will be shifted to right/left side or up/down. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 17 NL6448BC33-53 (b) DE mode (Note1, Note2) Parameter Symbol Min. Typ. Max. Unit Remarks Frequency 1/tc 21.0 25.2 29.0 MHz 39.7 ns (typ.) Duty tcd 0.4 0.5 0.6 - Rise time, Fall time tcrf - - 10 ns Setup time tds 8 - - ns Hold time tdh 12 - - ns tdrf - - 10 ns CLK DATA (R0-R5) (G0-G5) (B0-B5) CLK-DATA Rise time, Fall time Pulse width Vsync Vsync-DE timing tvp 1 2 - H Setup time tvds 1 - - CLK Hold time tvdh 1 - - CLK tvrf - - 10 s 30.0 31.8 33.6 s - 800 - CLK Rise time, Fall time Horizontal DE Vertical (One frame) CLK-DE Cycle th Display period thd Cycle tv Display period tvd Setup time tdes 8 - - ns Hold time tdeh 12 - - ns tderf - - 10 ns Rise time, Fall time 640 CLK 16.1 16.7 17.2 ms - 525 - H 480 H - - - 31.4 kHz (typ.) 59.9 Hz (typ.) - - Note1: Definition of parameters is as follows. tc = 1CLK, tcd = tch/tc, th = 1H Note2: Hsync signal (Pin No.3 of CN1) is not used inside the product at DE mode. Do not keep pin open to avoid noise problem. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 18 NL6448BC33-53 4.9.3 Input signal timing chart (a) Fixed mode Vsync 1H tvp tvb tvd 33H (fixed) tvf 480H (fixed) 12H (fixed) Hsync 1 2 1 3 Hsync DATA (R0-R5) (G0-G5) (B0-B5) D(X,0) INVALID D(X,478)D(X,479) D(X,Y) INVALID (Note: X=0 to 639) Hsync DATA (R0-R5) (G0-G5) (B0-B5) D(0,Y)D(1,Y) INVALID Hsync D(X,Y) D(638,Y)D(639,Y) INVALID 1CLK thp thb thf thd 640H (fixed) 144H (fixed) 16H (fixed) CLK 1 2 1 DATA (R0-R5) (G0-G5) (B0-B5) INVALID D(0,Y)D(1,Y) D(639,Y) INVALID (Note: Y=0 to 479) PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 19 NL6448BC33-53 (b) DE mode Horizontal timing CLK DATA (R0-R5) (G0-G5) (B0-B5) INVALID 1 2 639 640 INVALID DE thd th Vertical timing tvp Vsync DATA (R0-R5) (G0-G5) (B0-B5) INVALID INVALID 1 2 tvds 479 480 tvdh DE tvd tv PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 20 NL6448BC33-53 (c) Common 2 tc tch CLK 0.7VCC 0.5VCC 0.3VCC tcrf tcrf tds DATA 0.7VCC (R0-R5) (G0-G5) 0.5VCC (B0-B5) 0.3VCC tdrf tdrf tdeh DE tdh INVALID tdes tdeh 0.7VCC 0.5VCC 0.3VCC tderf CLK tdes tderf 0.5VCC thh ths 0.7VCC Hsync 0.5VCC 0.3VCC thrf Hsync 0.5VCC thv Vsync 0.7VCC 0.5VCC 0.3VCC tvh tvrf PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 21 NL6448BC33-53 4.10 OPTICS 4.10.1 Optical characteristics Parameter Note1 Condition Symbol Min. Typ. Max. Unit Remarks L 280 350 - cd/m2 - CR 150 300 - - Note2 - LU - 1.25 1.40 - Note3 x coordinate Wx - 0.313 - - y coordinate Wy - 0.329 - - x coordinate Rx - TBD - - y coordinate Ry - TBD - - x coordinate Gx - TBD - - y coordinate Gy - TBD - - x coordinate Bx - TBD - - y coordinate By - TBD - - R = 0, L = 0, U = 0, D = 0 at center, against NTSC color space C 35 40 - % Black to White Ton - 24 TBD ms White to Black Toff - 21 TBD ms Right U = 0, D = 0, CR = 10 R 70 85 - Left U = 0, D = 0, CR = 10 L 70 85 - Up R = 0, L = 0, CR = 10 U 70 85 - Down R = 0, L = 0, CR = 10 D 70 85 - White at center R = 0, L = 0, U = 0, D = 0 White/Black at center R = 0, L = 0, U = 0, D = 0 Luminance Contrast ratio Luminance uniformity White Red Chromaticity Green Blue Color gamut Response time Viewing angle Note4 2 Note5 Note6 2 Note7 Note1: Measurement conditions are as follows. Ta=25C, VCC=3.3V, IBL= 5.0mArms/lamp, Display mode: VGA, Horizontal cycle = 31.4kHz, Vertical cycle = 59.9Hz, DPS= Low or open: Normal scan Optical characteristics are measured at luminance saturation after 20minutes from working the product, in the dark room. Also measurement method for luminance is as follows. 50cm Photodetector (TOPCON BM-5A) LCD module 1 (Product) Note2: See "4.10.2 Definition of contrast ratio". Note3: See "4.10.3 Definition of luminance uniformity". Note4: These coordinates are found on CIE 1931 chromaticity diagram. Note5: Product surface temperature: TopF = TBDC Note6: See "4.10.4 Definition of response times". Note7: See "4.10.5 Definition of viewing angles". PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 22 NL6448BC33-53 4.10.2 Definition of contrast ratio The contrast ratio is calculated by using the following formula. Luminance of white screen Contrast ratio (CR) = Luminance of black screen 4.10.3 Definition of luminance uniformity The luminance uniformity is calculated by using following formula. Maximum luminance from to Luminance uniformity (LU) = Minimum luminance from to The luminance is measured at near the 5 points shown below. 106 320 533 80 240 400 4.10.4 Definition of response times Response time is measured, the luminance changes from "black" to "white", or "white" to "black" on the same screen point, by photo-detector. Ton is the time it takes the luminance change from 10% up to 90%. Also Toff is the time it takes the luminance change from 90% down to 10% (See the following diagram.). White 100% 90% Luminance Black 10% 0% Toff Ton 4.10.5 Definition of viewing angles Normal axis (Perpendicular) 12 o'clock 9 o'clock L Left D Lower U Upper R 3 o'clock Right PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 23 NL6448BC33-53 5. RELIABILITY TESTS 2 Test item Condition High temperature and humidity (Operation) 60 3C, RH = 90%, 240hours Display data is white. High temperature (Operation) 70 3C, 240hours Display data is white. Heat cycle (Operation) -10 3C...1hour 70 3C...1hour 50cycles, 4hours/cycle Display data is white. -20 3C...30minutes 80 3C...30minutes 100cycles, 1hour/cycle Temperature transition time is within 5 minutes. Thermal shock (Non operation) ESD (Operation) 150pF, 150, 10kV 9 places on a panel surface Note2 10 times each places at 1 sec interval Dust (Operation) Sample dust: No. 15 (by JIS-Z8901) 15 seconds stir 8 times repeat at 1 hour interval 5 to 100Hz, 19.6m/s2 1 minute/cycle X, Y, Z direction 120 times each directions Vibration (Non operation) Mechanical shock (Non operation) Judgement 539m/ s2, 11ms X, Y, Z direction 5 times each directions No display malfunctions Note1 No display malfunctions Note1 No physical damages Note1: Display functions are checked under the same conditions as product inspection. Note2: See the following figure for discharge points. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 24 NL6448BC33-53 6. PRECAUTIONS 6.1 MEANING OF CAUTION SIGNS The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS" and "6.3 ATTENTIONS", after understanding this contents! This sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. ! This sign has the meaning that customer will get an electrical shock, if customer has wrong operations. This sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 CAUTIONS Do not touch the working backlight. Customer will be in danger of an electric shock. Do not touch the working backlight. Customer will be in danger of burn injury. Do not shock and press the LCD panel and the backlight! There is a danger of breaking, because they are made of glass. (Shock: To be not greater 539m/s2 and to be not greater 11ms, Pressure: To be not greater TBD N) 6.3 ATTENTIONS ! 6.3.1 Handling of the product Take hold of both ends without touch the circuit board cover when customer pulls out products (LCD modules) from inner packing box. If customer touches it, products may be broken down or out of adjustment, because of stress to mounting parts. Do not hook cables nor pull connection cables such as lamp cable and so on, for fear of damage. If customer puts down the product temporarily, the product puts on flat subsoil as a display side turns down. Take the measures of electrostatic discharge such as earth band, ionic shower and so on, when customer deals with the product, because products may be damaged by electrostatic. The torque for mounting screws must never exceed 0.294Nm. Higher torque values might result in distortion of the bezel. The product must be installed using mounting holes without undue stress such as bends or twist (See outline drawings). And do not add undue stress to any portion (such as bezel flat area) except mounting hole portion. Bends or twist described above and undue stress to any portion except mounting hole portion may cause display un-uniformity. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 25 2 NL6448BC33-53 Do not press or rub on the sensitive display surface. If customer clean on the panel surface, NEC Corporation recommends using the cloth with ethanolic liquid such as screen cleaner for LCD. Do not push-pull the interface connectors while the product is working, because wrong power sequence may break down the product. Do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high voltage side of the lamp. This damage may cause a lamp breaking and abnormal operation of high voltage circuit. 6.3.2 Environment Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. Keep the product in antistatic pouch in room temperature, because of avoidance for dusts and sunlight, if customer stores the product. In order to prevent dew condensation occurring by temperature difference, the product packing box must be opened after leave under the environment of an unpacking room temperature enough. Because a situation of dew condensation occurring is changed by the environmental temperature and humidity, evaluate the leaving time sufficiently. (Recommendation leaving time: 6 hour or more with packing state) Do not operate in high magnetic field. Circuit boards may be broken down by it. Use an original protection sheet on the product surface (polarizer). Adhesive type protection sheet should be avoided, because it may change color or properties of the polarizer. 6.3.3 Characteristics The following items are neither defects nor failures. Response time, luminance and color may be changed by ambient temperature. The LCD may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display patterns. Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because the LCD has cold cathode fluorescent lamps. Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen saver, if the fixed pattern is displayed on the screen. The display color may be changed by viewing angle because of the use of condenser sheet in the backlight. Optical characteristics may be changed by input signal timings. The interference noise of input signal frequency for this product's signal processing board and luminance control frequency of customer's backlight inverter may appear on a display. Set up luminance control frequency of backlight inverter so that the interference noise does not appear. 6.3.4 Other All GND, backlight inverter ground (GNDB), VCC and backlight inverter power supply voltage (VDDB) terminals should be used without a non-connected line. Do not disassemble a product or adjust volume without permission of NEC Corporation. See "REPLACEMENT MANUAL FOR LAMP HOLD ERSET", if customer would like to replace backlight lamps. Pay attention not to insert waste materials inside of products, if customer uses screwnails. Pack the product with original shipping package, because of avoidance of some damages during transportation, when customer returns it to NEC Corporation for repair and so on. PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) 26 2 NL6448BC33-53 7. OUTLINE DRAWINGS 7.1 FRONT VIEW Note1: The values in parentheses are for reference. Note2: The torque for mounting screws must never exceed 0.294Nm. Note3: Mounting hole portions (4 pieces) PRELIMINARY DATA SHEET DOD-M-1309 (2nd edition) Unit : mm 2 27 NL6448BC33-53 7.2 REAR VIEW Note1: The values in parentheses are for reference. Note2: The torque for mounting screws must never exceed 0.294Nm. PRELIMINARY DATA SHEET DOD-M-1309 (2nd edition) Unit : mm 28 NL6448BC33-53 REVISION HISTORY Edition 1st edition Document number DOD-M1218 Prepared date Nov. 5, 2002 Revision contents and signature Revision contents New issue Writer Approved by Checked by T. ITO 2nd edition DOD-M1309 Jan. 30, 2003 Prepared by R. KAWASHIMA Revision contents P.5 * Weight : TBD g (typ.) 475g (typ.) P.5,22 * Response time : Ton TBD ms (typ.) 24ms (typ.) Toff TBD ms (typ.) 21 ms (typ.) P.5 * Backlight : Lamp holder set;Type No. 104LHS35 104LHS39 Inverter; Type No. TBD 104PW191, 104PW161 * Power consumption : TBD W (typ.) 6.2 W (typ.) P.7 * Weight : TBD g (typ.) 475g (typ.) TBD g (max.) 500g (max.) P.8 * ICC : TBD mA (Typ.) 280 mA (Typ.) (VCC=3.3V) TBD mA (Max..) 400 mA (Max.) (VCC=3.3V) TBD mA (Typ.) 200 mA (Typ.) (VCC=5.0V) TBD mA (Max..) 280 mA (Max.) (VCC=5.0V) P.9 * FO : TBD kHz (Min.) 50kHz (Min.) TBD kHz (typ.) - kHz (typ.) TBD kHz (Max.) 70kHz (Max.) P.21 * Input signal timing chart- (C) Common The timing between each display signal : 0.7VCC, 0.3VCC 0.5VCC P.24 * Reliability tests : decided P.25 * Handling of the product : (added) P.26 * Environment : (added) P.27 * Outline drawings-Front view : Note3 (added) Signature of writer Approved by T. ITO Checked by R. KAWASHIMA PRELIMINARY DATA SHEET DOD-M- 1309 (2nd edition) Prepared by A. KUMANO 29