2SC5692
2013-11-01
1
TOSHIBA Transistor Silicon NPN Epitaxial Type
2SC5692
High-Speed Switching Applications
DC-DC Converter Applications
Strobe Applications
High DC current gain: hFE = 400 to 1000 (IC = 0.3 A)
Low collector-emitter saturation voltage: VCE (sat) = 0.14 V (max)
High-speed switching: tf = 120 ns (typ.)
Absolute Maximum Ratings (Ta = 25°C)
Characteristics Symbol Rating Unit
Collector-base voltage VCBO 100 V
Collector-emitter voltage VCEX 80 V
Collector-emitter voltage VCEO 50 V
Emitter-base voltage VEBO 7 V
DC IC 2.5
Collector current
Pulse ICP 4.0
A
Base current IB 250 mA
DC 625
Collector power
dissipation t = 10 s
PC
(Note 1) 1000
mW
Junction temperature Tj 150 °C
Storage temperature range Tstg 55 to 150 °C
Note 1: Mounted on an FR4 board (glass epoxy, 1.6 mm thick, Cu area: 645 mm2)
Note 2: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Unit: mm
JEDEC
JEITA
TOSHIBA 2-3S1C
Weight: 0.01 g (typ.)
Start of commercial production
2000-05
2SC5692
2013-11-01
2
Electrical Characteristics (Ta = 25°C)
Characteristics Symbol Test Condition Min Typ. Max Unit
Collector cut-off current ICBO V
CB = 100 V, IE = 0 100 nA
Emitter cut-off current IEBO V
EB = 7 V, IC = 0 100 nA
Collector-emitter breakdown voltage V (BR) CEO IC = 10 mA, IB = 0 50 V
hFE (1) VCE = 2 V, IC = 0.3 A 400 1000
DC current gain
hFE (2) VCE = 2 V, IC = 1 A 200
Collector-emitter saturation voltage VCE (sat) I
C = 1 A, IB = 20 mA 0.14 V
Base-emitter saturation voltage VBE (sat) I
C = 1 A, IB = 20 mA 1.10 V
Collector output capacitance Cob V
CB = 10 V, IE = 0, f = 1 MHz 13 pF
Rise time tr 40
Storage time tstg 500
Switching time
Fall time tf
See Figure 1.
VCC
30 V, RL = 30 Ω
IB1 = IB2 = 33.3 mA 120
ns
Marking
W B
Part No. (or abbreviation code)
Lot code (month)
Lot code (year)
Dot: even year
No dot: odd year
Figure 1 Switching Time Test Circuit &
Timin
g
Chart
IB2
IB1
20 μs
Output
Input
IB2
IB1
RL
VCC
Duty cycle < 1%
2SC5692
2013-11-01
3
Base-emitter voltage VBE (V)
Collector current IC (A)
Base-emitter saturation voltage
VBE (sat) (V)
Collector-emitter voltage VCE (V)
IC – VCE
Collector current IC (A)
Collector current IC (A)
hFE – IC
DC current gain hFE
Collector current IC (A)
VCE (sat) – IC
Collector-emitter saturation voltage
VCE (sat) (V)
Collector current IC (A)
VBE (sat) – IC
IC – VBE
10000
0.001
1000
100
10
0.01 0.1 1 10
Common emitter
VCE = 2 V
Single nonrepetitive
pulse
Ta = 100°C
25 55
0.001 0.01 0.1 1 10
10
0.1
1
25
Common emitter
IC/IB = 50
Single nonrepetitive pulse
100
Ta = 55°C
0.001
1
0.1
0.01
0.001 0.01 0.1 1 10
Common emitter
IC/IB = 50
Single nonrepetitive
pulse
25
55
Ta = 100°C
0
0
Common emitter
Ta = 25°C
Single nonrepetitive pulse
3
2.5
2
1.5
1
0.5
0.2
70 50 40
30
20
10
5
IB = 1 mA
0.4 0.6 1 0.8
60
Common emitter
VCE = 2 V
Single nonrepetitive
pulse
0
0.4 0.8 1.2 1.6
0
3
2
1
Ta = 100°C 25
55
2SC5692
2013-11-01
4
Collector-emitter voltage VCE (V)
Collector current IC (A)
Transient Thermal Resistance rth – tw
Pulse width tw (s)
Transient thermal resistance
rth (°C/W)
Curves should be applied in thermal limited area.
Single nonrepetitive pulse Ta = 25°C
Mounted on an FR4 board (glass epoxy, 1.6 mm thick, Cu
area: 645 mm2)
1000
1
0.001
100
10
0.01 0.1 1 10 100 1000
Safe Operating Area
10
0.01
0.1 1 10 100
0.1
1
IC max (pulsed)
DC operation *
(Ta = 25°C)
VCEO max
10 μs
100 μs 1 ms
100 ms*
10 ms
10 s*
: Single nonrepetitive pulse
Ta = 25°C
Note that the curves for 100 ms*,
10 s* and DC operation* will be
different when the devices aren’t
mounted on an FR4 board (glass
epoxy, 1.6 mm thick, Cu area:
645 mm2). These characteristic
curves must be derated linearly
with increase in temperature.
IC max (continuous)
2SC5692
2013-11-01
5
RESTRICTIONS ON PRODUCT USE
Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively "Product") without notice.
This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR
APPLICATIONS.
PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE
EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH
MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT
("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without
limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for
automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions,
safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE
PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your
TOSHIBA sales representative.
Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the
U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited
except in compliance with all applicable export laws and regulations.
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES
OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS.