■Specifications
■Dimensions
※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105°C .
※2 Refer to Page 56 for reflow soldering conditions.
C5
C55
φD±0.5
6.3
6.3
W±0.2
4.9
5.4
6.6
6.6
H±0.2
6.6
6.6
C±0.2
7.3
7.3
R
0.6 to 0.8
0.6 to 0.8
P±0.2
2.1
2.1
Size Code
(unit : mm)
■Size List
24
RV : Rated voltage (SV) : Surge (room temperature)
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
φD
L
P
R
C
W
0.2max.
H
（＋）
This is a low profile series based on the SVPA series. Suitable for
miniaturizing devices and circuits.
This product can support lead free-reflow (※2).
Marking : Polarity( ), Rated voltage,
(Purple) PB Rated capacitance, Lot.No.
※For the minimum packing quantity, please refer to page 55.
Conductive polymer type
SVPBSeries Low profile
RV
（SV）
µ
F
15
22
33
56
82
100
120 C5
2.5
（3.3）
C5
4.0
（5.2）
C5
6.3
（8.2）
C5
10.0
（11.5）
C5
16.0
（18.4）
C5
C55
20.0
（23.0）
L+0.1
-0.4
Items Characteristics
-55°C to +105°C
M :±20%
Less than or equal to the value of Table4
Less than or equal to the value of Table4
Less than or equal to the value of Table4
Within ±20% (±30% for C5 size)
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard (after voltage processing)
Within ±10% (±20% for C5 size)
1.3 times or less than an initial standard
1.3 times or less than an initial standard
Below an initial standard (after voltage processing)
Category temperature range
Tolerance on rated capacitance
Tangent of loss angle
Leakage current
ESR
Endurance
Damp heat (Steady state)
Characteristics of impedance
ratio at high temp. and low temp.
-55°C
+105°C
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Resistance to
soldering heat
Z / Z 20°C
Z / Z 20°C
0.75 to 1.25
0.75 to 1.25
120Hz
120Hz
105°C, 1,000h, Rated
voltage applied
60°C, 90 to 95% RH,
1,000h,
No-applied voltage
(VPS) (230°C X 75s)
※1
※2
Conditions
Based the value at
100KHz，+20°C
After 2 minutes
25
■Table4 SVPB Series Characteristics List
Rated
Voltage
(V)
Rated
Capacitance
(µF)
※1 Capacitance tolerance : M ±20%
※2 After 2 minutes
●The C5 size is also available upon request as a radial lead type. Please contact us if this type is required. Maximum
height for radial lead types is 4.5 mm.
●The C55 size is also available upon request as 4V and 6.3V products.
C5
20SVPB15M
16SVPB33M
10SVPB56M
6SVPB82M
4SVPB100M
2R5SVPB120M
20SVPB22M
20
16
10
6.3
4
2.5
20
15
33
56
82
100
120
22
45
40
40
40
40
40
35
2000
1670
1670
1670
1670
1670
2000
0.12
0.12
0.12
0.12
0.12
0.12
0.12
120
211
224
207
160
120
88
Size
Code
C55
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
Part Number
※1
Tangent of
loss angle
(max.)
Leakage
current (µA)
(max.)※2
Rated
ripple current
100kHz (mArms)
at 105°C
ESR
100kHz to 300kHz
(mΩ) (max.)
■Recommended land pattern
dimension of PWB
(unit : mm)
c
a
b
Size Code
C5
C55
ab c
2.1
2.1
9.1
9.1
1.6
1.6
Frequency coefficient for ripple current
Frequency
Coefficient
120Hz≦ f ＜1kHz
0.05
1kHz≦ f ＜10kHz
0.3
10kHz≦ f ＜100kHz
0.7
100kHz≦ f ≦500kHz
1