LTC3859 Low IQ, Triple Output, Buck/Buck/Boost Synchronous Controller DESCRIPTION FEATURES n n n n n n n n n n n n n n n Dual Buck Plus Single Boost Synchronous Controllers Outputs Remain in Regulation Through Cold Crank Down to 2.5V Low Operating IQ: 55A (One Channel On) Wide Bias Input Voltage Range: 4.5V to 38V Buck Output Voltage Range: 0.8V VOUT 24V Boost Output Voltage Up to 60V RSENSE or DCR Current Sensing 100% Duty Cycle for Boost Synchronous MOSFET Phase-Lockable Frequency (75kHz to 850kHz) Programmable Fixed Frequency (50kHz to 900kHz) Selectable Continuous, Pulse-Skipping or Low Ripple Burst Mode(R) Operation at Light Loads Very Low Buck Dropout Operation: 99% Duty Cycle Adjustable Output Voltage Soft-Start or Tracking Low Shutdown IQ: 14A Small 38-Pin 5mm 7mm QFN and TSSOP Packages APPLICATIONS n n n Automotive Always-On and Start-Stop Systems Battery Operated Digital Devices Distributed DC Power Systems The LTC(R)3859 is a high performance triple output (buck/ buck/boost) synchronous DC/DC switching regulator controller that drives all N-channel power MOSFET stages. Constant frequency current mode architecture allows a phase-lockable switching frequency of up to 850kHz. The LTC3859 operates from a wide 4.5V to 38V input supply range. When biased from the output of the boost converter or another auxiliary supply, the LTC3859 can operate from an input supply as low as 2.5V after start-up. The 55A no-load quiescent current extends operating runtime in battery powered systems. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3859 features a precision 0.8V reference for the bucks, 1.2V reference for the boost and a power good output indicator. Independent TRACK/SS pins for each controller ramp the output voltages during start-up. Current foldback limits MOSFET heat dissipation during short-circuit conditions. The PLLIN/MODE pin selects among Burst Mode operation, pulse-skipping mode, or continuous inductor current mode at light loads. L, LT, LTC, LTM, Burst Mode, OPTI-LOOP and Module are registered trademarks and No RSENSE is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5705919, 5929620, 6144194, 6177787, 6580258. TYPICAL APPLICATION 220F 1F 499k VFB3 Efficiency vs Input Voltage VBIAS TG1 68.1k 100 4.9H 2m VIN 2.5V TO 38V (START-UP ABOVE 5V) 1.2H 220F TG3 SW1 SW3 BG1 LTC3859 6m VOUT1 5V 5A BG3 + SENSE3- SENSE3+ INTVCC 4.7F BOOST1, 2, 3 SW1, 2, 3 SENSE1 SENSE1- VFB1 68.1k 357k 220F RUN1, 2, 3 EXTVCC ITH1, 2, 3 90 VOUT1 = 5V 85 80 75 70 65 60 0.1F TG2 SW2 BG2 VOUT2 = 8.5V 95 EFFICIENCY (%) VOUT3 REGULATED AT 10V WHEN VIN < 10V FOLLOWS VIN WHEN VIN > 10V 6.5H 8m VOUT2 8.5V 3A 55 FIGURE 12 CIRCUIT ILOAD = 2A 50 5 0 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 3859 TA01b 0.1F SENSE2+ SENSE2- TRACK/SS1, 2 VFB2 SS3 PGND SGND 68.1k 649k 68F 3859 TA01 3859fa 1 LTC3859 ABSOLUTE MAXIMUM RATINGS (Notes 1, 3) Bias Input Supply Voltage (VBIAS) .............. -0.3V to 40V Buck Top Side Driver Voltages (BOOST1, BOOST2) ............................. -0.3V to 46V Boost Top Side Driver Voltages (BOOST3) ............................................ -0.3V to 76V Buck Switch Voltage (SW1, SW2) ................ -5V to 40V Boost Switch Voltage (SW3) ........................ -5V to 70V INTVCC, (BOOST1-SW1), (BOOST2-SW2), (BOOST3-SW3),.......... -0.3V to 6V RUN1, RUN2, RUN3 .................................... -0.3V to 8V Maximum Current Sourced Into Pin from Source >8V...............................................100A SENSE1+, SENSE2 +, SENSE1- SENSE2 - Voltages ..................................... -0.3V to 28V SENSE3 +, SENSE3- Voltages ..................... -0.3V to 40V FREQ Voltages ...................................... -0.3V to INTVCC EXTVCC ....................................................... -0.3V to 14V ITH1, ITH2, ITH3, VFB1, VFB2, VFB3 Voltages .... -0.3V to 6V PLLIN/MODE, PGOOD1, OV3 Voltages ....... -0.3V to 6V TRACK/SS1, TRACK/SS2, SS3 Voltages ..... -0.3V to 6V Operating Junction Temperature Range (Note 2) .............................................-40C to 125C Storage Temperature Range...................-65C to 150C PIN CONFIGURATION TOP VIEW 4 35 SW1 FREQ 5 34 BOOST1 32 SW3 SS3 3 29 BG1 SENSE3+ 4 28 SW3 SENSE3- 5 27 TG3 9 30 BOOST3 ITH3 11 29 BG3 28 VBIAS SGND 12 27 EXTVCC RUN1 13 26 INTVCC RUN2 14 25 BG2 RUN3 15 24 BOOST2 SENSE2- 16 23 SW2 SENSE2+ 17 22 TG2 VFB2 18 21 OV3 ITH2 19 20 TRACK/SS2 FE PACKAGE 38-LEAD PLASTIC TSSOP TJMAX = 125C, qJA = 25C/W EXPOSED PAD (PIN 39) IS PGND, MUST BE SOLDERED TO PCB VFB3 6 26 BOOST3 39 PGND ITH3 7 25 BG3 SGND 8 24 VBIAS RUN1 9 23 EXTVCC RUN2 10 22 INTVCC RUN3 11 21 BG2 SENSE2- 12 20 BOOST2 13 14 15 16 17 18 19 SW2 SENSE3- TG2 31 TG3 OV3 8 ITH2 SENSE3+ TRACK/SS2 7 39 PGND 30 BOOST1 33 BG1 SS3 VFB3 10 31 SW1 PLLIN/MODE 2 VFB2 6 38 37 36 35 34 33 32 FREQ 1 SENSE2+ PLLIN/MODE TG1 36 TG1 SENSE1- PGOOD1 37 PGOOD1 3 TRACK/SS1 2 ITH1 VFB1 SENSE1+ VFB1 38 TRACK/SS1 SENSE1+ 1 SENSE1- TOP VIEW ITH1 UHF PACKAGE 38-LEAD (5mm s 7mm) PLASTIC QFN TJMAX = 125C, qJA = 34C/W EXPOSED PAD (PIN 39) IS PGND, MUST BE SOLDERED TO PCB 3859fa 2 LTC3859 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3859EFE#PBF LTC3859EFE#TRPBF LTC3859FE 38-Lead Plastic TSSOP -40C to 125C LTC3859IFE#PBF LTC3859IFE#TRPBF LTC3859FE 38-Lead Plastic TSSOP -40C to 125C LTC3859EUHF#PBF LTC3859EUHF#TRPBF 3859 38-Lead (5mm 7mm) Plastic QFN -40C to 125C LTC3859IUHF#PBF LTC3859IUHF#TRPBF 3859 38-Lead (5mm 7mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless otherwise noted. (Note 2) SYMBOL PARAMETER VBIAS Bias Input Supply Operating Voltage Range Buck Regulated Feedback Voltage VFB1,2 CONDITIONS IFB1,2,3 Feedback Current VREFLNREG Reference Voltage Line Regulation (Note 4); VIN = 4V to 38V VLOADREG Output Voltage Load Regulation (Note 4) Measured in Servo Loop; DITH Voltage = 1.2V to 0.7V Measured in Servo Loop; DITH Voltage = 1.2V to 2V (Note 4); ITH1,2,3 = 1.2V; Sink/Source 5A (Note 5) RUN1 = 5V and RUN2,3 = 0V or RUN2 = 5V and RUN1,3 = 0V or RUN3 = 5V and RUN1,2 = 0V VFB1, 2 ON = 0.83V (No Load) VFB3 = 1.25V RUN1,2,3 = 5V, VFB1,2 = 0.83V (No Load) VFB3 = 1.25V RUN1 = 5V and RUN2,3 = 0V or RUN2 = 5V and RUN1,3 = 0V VFB,ON = 0.83V (No Load) RUN3 = 5V and RUN1,2 = 0V VFB3 = 1.25V RUN1 = 5V and RUN2 = 0V or RUN2 = 5V and RUN1 = 0V RUN3 = 5V VFB1,2 = 0.83V (No Load) VFB3 = 1.25V RUN1,2,3 = 5V, VFB1,2 = 0.83V (No Load) VFB3 = 1.25V RUN1,2,3 = 0V Boost Regulated Feedback Voltage gm1,2,3 Transconductance Amplifier gm IQ Input DC Supply Current Pulse-Skipping or Forced Continuous Mode (One Channel On) Pulse-Skipping or Forced Continuous Mode (All Channels On) Sleep Mode (One Channel On, Buck) Sleep Mode (One Channel On, Boost) Sleep Mode (Buck and Boost Channel On) Sleep Mode (All Three Channels On) Shutdown TYP 4.5 (Note 4); ITH1,2 Voltage = 1.2V -40C to 125C -40C to 85C (Note 4); ITH3 Voltage = 1.2V -40C to 125C -40C to 85C (Note 4) VFB3 MIN MAX UNITS 38 V l 0.788 0.792 0.800 0.800 0.812 0.808 V V l 1.182 1.188 1.200 1.200 5 1.218 1.212 50 V V nA 0.002 0.02 %/V l 0.01 0.1 % l -0.01 -0.1 % 2 mmho 2 mA 3 mA 55 80 A 55 80 A 65 100 A 80 120 A 14 30 A 3859fa 3 LTC3859 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS UVLO Undervoltage Lockout VOVL1,2 Buck Feedback Overvoltage Protection ISENSE1,2+ SENSE+ Pin Current INTVCC Ramping Up INTVCC Ramping Down Measured at VFB1,2 Relative to Regulated VFB1,2 Bucks (Channels 1 and 2) ISENSE3+ SENSE+ Pin Current Boost (Channel 3) ISENSE1,2- SENSE- Pin Current ISENSE3 - SENSE- Pin Current DFMAX,TG Maximum Duty Factor for TG DFMAX,BG Maximum Duty Factor for BG ITRACK/SS1,2 Soft-Start Charge Current Bucks (Channels 1 and 2) VOUT1,2 < VINTVCC - 0.5V VOUT1,2 > VINTVCC + 0.5V Boost (Channel 3) VSENSE3+, VSENSE3 - = 12V Bucks (Channels 1,2) in Dropout, FREQ = 0V Boost (Channel 3) in Overvoltage Bucks (Channels 1,2) in Overvoltage Boost (Channel 3) VTRACK/SS1,2 = 0V ISS3 Soft-Start Charge Current VSS3 = 0V VRUN1 ON VRUN2,3 ON VRUN1,2,3 Hyst RUN1 Pin Threshold RUN2,3 Pin Threshold RUN Pin Hysteresis VRUN1 Rising VRUN2,3 Rising VFB1,2 = 0.7V, VSENSE1,2- = 3.3V VFB1,2,3 = 1.1V, VSENSE3 + = 12V VSENSE1,2,3(MAX) Maximum Current Sense Threshold VSENSE3(CM) SENSE3 Pins Common Mode Range (BOOST Converter Input Supply Voltage) MIN TYP MAX 3.5 7 4.15 3.8 10 4.5 4.0 13 V V % 1 A l l 170 UNITS A 2 1 A A A 0.7 99 100 100 96 1.0 1.4 % % % % A 0.7 1.0 1.4 A l l 1.19 1.23 1.25 1.28 80 1.31 1.33 V V mV l 43 50 57 mV 38 V 700 98 2.5 Gate Driver TG1,2 tON(MIN)1,2 Pull-Up On-Resistance Pull-Down On-Resistance Pull-Up On-Resistance Pull-Down On-Resistance Pull-Up On-Resistance Pull-Down On-Resistance Pull-Up On-Resistance Pull-Down On-Resistance TG Transition Time: Rise Time Fall Time BG Transition Time: Rise Time Fall Time Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time Buck Minimum On-Time (Note 6) CLOAD = 3300pF CLOAD = 3300pF (Note 6) CLOAD = 3300pF CLOAD = 3300pF CLOAD = 3300pF Each Driver Bucks (Channels 1, 2) Boost (Channel 3) CLOAD = 3300pF Each Driver Bucks (Channels 1, 2) Boost (Channel 3) (Note 7) tON(MIN)3 Boost Minimum On-Time (Note 7) BG1,2 TG3 BG3 TG1,2,3 tr TG1,2,3 tf BG1,2,3 tr BG1,2,3 tf TG/BG t1D BG/TG t1D 2.5 1.5 2.4 1.1 1.2 1.0 1.2 1.0 25 16 ns ns 28 13 30 70 30 70 95 ns ns ns ns ns ns ns 120 ns 3859fa 4 LTC3859 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VBIAS = 12V, VRUN1,2,3 = 5V, EXTVCC = 0V unless otherwise noted. (Note 2) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 5.0 5.4 5.6 V 0.7 2 % 5.4 5.6 V 0.7 2 % INTVCC Linear Regulator VINTVCCVBIAS Internal VCC Voltage 6V < VBIAS < 38V, VEXTVCC = 0V, IINTVCC = 0mA VLDOVBIAS INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 0V VINTVCCEXT Internal VCC Voltage 6V < VEXTVCC < 13V, IINTVCC = 0mA VLDOEXT INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 8.5V VEXTVCC EXTVCC Switchover Voltage EXTVCC Ramping Positive VLDOHYS EXTVCC Hysteresis 5.0 4.5 4.7 V 200 mV 115 kHz Oscillator and Phase-Locked Loop f25k Programmable Frequency RFREQ = 25k; PLLIN/MODE = DC Voltage f65k Programmable Frequency RFREQ = 65k; PLLIN/MODE = DC Voltage f105k Programmable Frequency RFREQ = 105k; PLLIN/MODE = DC Voltage fLOW Low Fixed Frequency fHIGH fSYNC 375 440 505 kHz VFREQ = 0V PLLIN/MODE = DC Voltage 320 350 380 kHz High Fixed Frequency VFREQ = INTVCC; PLLIN/MODE = DC Voltage 485 535 585 kHz Synchronizable Frequency PLLIN/MODE = External Clock 850 kHz 835 l 75 kHz PGOOD1 Output VPGL1 PGOOD1 Voltage Low IPGOOD1 = 2mA IPGOOD1 PGOOD1 Leakage Current VPGOOD1 = 5V VPG1 PGOOD1 Trip Level VFB1 with Respect to Set Regulated Voltage VFB1 Ramping Negative Hysteresis VFB1 Ramping Positive Hysteresis TPG1 0.2 -13 7 Delay For Reporting a Fault 0.4 V 1 A -10 2.5 10 2.5 20 -7 13 % % % % s 0.2 0.4 V 1 A 13 % % OV3 Boost Overvoltage Indicator Output VOV3L OV3 Voltage Low IOV3 = 2mA IOV3 OV3 Leakage Current VOV3 = 5V VOV OV3 Trip Level VFB With Respect to Set Regulated Voltage Hysteresis 6 10 1.5 BOOST3 Charge Pump IBST3 BOOST3 Charge Pump Available Output Current VBOOST3 = 16V; VSW3 = 12V; Forced Continuous Mode 65 A 3859fa 5 LTC3859 ELECTRICAL CHARACTERISTICS Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3859 is tested under pulsed load conditions such that TJ TA. The LTC3859E is guaranteed to meet specifications from 0C to 85C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3859I is guaranteed over the full -40C to 125C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature (TJ in C) is calculated from the ambient temperature (TA in C) and power dissipation (PD, in Watts) according to the formula TJ = TA + (PD * qJA), where qJA = 34C/W for the QFN package and qJA = 25C/W for the TSSOP package. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 4: The LTC3859 is tested in a feedback loop that servos VITH1,2,3 to a specified voltage and measures the resultant VFB1,2,3. The specification at 85C is not tested in production. This specification is assured by design, characterization and correlation to production testing at 125C. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications information. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: See Minimum On-Time Considerations in the Applications Information section. 3859fa 6 LTC3859 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency and Power Loss vs Output Current (Buck) 100 Efficiency vs Output Current (Buck) 100 50 CCM EFFICIENCY 10 PULSE-SKIPPING 30 EFFICIENCY BURST LOSS 20 BURST EFFICIENCY 1 CCM LOSS 10 PULSE-SKIPPING LOSS 0.1 0 0.0001 0.001 0.1 0.01 1 10 OUTPUT CURRENT (A) 3859 G01 FIGURE 12 CIRCUIT VIN = 10V, VOUT = 5V 40 98 70 60 50 40 97 96 95 30 94 20 93 10 FIGURE 12 CIRCUIT 0 0.0001 0.001 0.1 0.01 1 OUTPUT CURRENT (A) 92 10 0 10 15 20 25 30 INPUT VOLTAGE (V) VOUT 100mV/DIV AC-COUPLED IL 2A//DIV IL 2A//DIV 3859 G04 Inductor Current at Light Load (Buck) 40 Load Step (Buck) Forced Continuous Mode VOUT 100mV/DIV AC-COUPLED IL 2A//DIV 35 3859 G03 Load Step (Buck) Pulse-Skipping Mode VOUT 100mV/DIV AC-COUPLED 5 3859 G02 Load Step (Buck) Burst Mode Operation 50s/DIV VIN = 12V VOUT = 5V FIGURE 12 CIRCUIT VIN = 20V EFFICIENCY (%) 60 EFFICIENCY (%) 70 FIGURE 12 CIRCUIT 99 VOUT = 5V ILOAD = 4A VIN = 10V 80 1000 POWER LOSS (mW) EFFICIENCY (%) 100 90 90 80 Efficiency vs Input Voltage (Buck) 100 10000 3859 G05 50s/DIV VIN = 12V VOUT = 5V FIGURE 12 CIRCUIT 3859 G06 50s/DIV VIN = 12V VOUT = 5V FIGURE 12 CIRCUIT Buck Regulated Feedback Voltage vs Temperature Soft Start-Up VOUT2 2V/DIV Burst Mode OPERATION 1A/DIV VOUT1 2V/DIV PULSESKIPPING MODE 2s/DIV VIN = 10V VOUT = 5V ILOAD = 1mA FIGURE 12 CIRCUIT 3859 G07 2ms/DIV FIGURE 12 CIRCUIT 3859 G08 REGULATED FEEDBACK VOLTAGE (mV) 808 FORCED CONTINUOUS MODE 806 804 802 800 798 796 794 792 -45 -20 30 55 80 5 TEMPERATURE (C) 105 130 3859 G09 3859fa 7 LTC3859 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency and Power Loss vs Output Current (Boost) Efficiency vs Output Current (Boost) 10000 100 90 90 1000 60 100 50 CCM EFFICIENCY 40 PULSE-SKIPPING 10 EFFICIENCY 30 BURST LOSS BURST 20 1 EFFICIENCY CCM LOSS 10 PULSE-SKIPPING LOSS 0.1 0 0.01 1 10 0.0001 0.001 0.1 OUTPUT CURRENT (A) 3859 G10 FIGURE 12 CIRCUIT VIN = 5V, VOUT = 10V, VBIAS = VIN VIN = 8V VIN = 5V 80 EFFICIENCY (%) 70 POWER LOSS (mW) EFFICIENCY (%) 80 Efficiency vs Input Voltage (Boost) 100 70 EFFICIENCY (%) 100 60 50 40 FIGURE 12 CIRCUIT 99 VBIAS = VIN V = 10V 98 OUT ILOAD = 2A 97 96 95 94 30 93 20 92 FIGURE 12 CIRCUIT 10 VBIAS = VIN VOUT = 10V 0 0.0001 0.001 0.1 0.01 1 OUTPUT CURRENT (A) 91 90 10 3 4 5 6 7 8 INPUT VOLTAGE (V) 3859 G11 Load Step (Boost) Burst Mode Operation Load Step (Boost) Pulse-Skipping Mode VOUT 100mV/DIV AC-COUPLED IL 5A/DIV IL 5A/DIV IL 5A/DIV 200s/DIV VOUT = 10V VIN = 5V FIGURE 12 CIRCUIT Inductor Current at Light Load (Boost) 10 Load Step (Boost) Forced Continuous Mode VOUT 100mV/DIV AC-COUPLED 3859 G13 9 3859 G12 VOUT 100mV/ DIV ACCOUPLED 200s/DIV VOUT = 10V VIN = 5V FIGURE 12 CIRCUIT 2 3859 G14 200s/DIV VOUT = 10V VIN = 5V FIGURE 12 CIRCUIT 3859 G15 Boost Regulated Feedback Voltage vs Temperature Soft Start-Up (Boost) Burst Mode OPERATION 5A/DIV VOUT3 2V/DIV PULSESKIPPING MODE GND 2s/DIV VOUT = 10V VIN = 7V ILOAD = 1mA FIGURE 12 CIRCUIT 3859 G16 2ms/DIV VIN = 5V FIGURE 12 CIRCUIT 3859 G17 REGULATED FEEDBACK VOLTAGE (V) 1.212 FORCED CONTINUOUS MODE 1.209 1.206 1.203 1.200 1.197 1.194 1.191 1.188 -45 -20 30 55 80 5 TEMPERATURE (C) 105 130 3859 G18 3859fa 8 LTC3859 TYPICAL PERFORMANCE CHARACTERISTICS INTVCC and EXTVCC vs Load Current INTVCC Line Regulation 5.5 5.50 EXTVCC Switchover and INTVCC Voltages vs Temperature 6.0 VBIAS = 12V 5.8 EXTVCC AND INTVCC VOLTAGE (V) 5.45 INTVCC VOLTAGE (V) INTVCC VOLTAGE (V) 5.4 5.3 5.2 5.40 EXTVCC = 0V EXTVCC = 8.5V 5.35 5.30 5.25 5.1 5.20 5.0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 5.15 40 0 SENSE3 PIN VOUT = 28V 100 600 500 400 300 60 5 30 35 55 80 TEMPERATURE (C) 0 -45 -20 105 130 60 BOOST BUCK 40 30 20 10 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) 3859 G25 SENSE3- PIN 5 30 35 55 80 TEMPERATURE (C) Soft-Start Pull-Up Current vs Temperature 60 1.20 50 1.15 40 1.10 30 20 10 0 1.05 1.00 0.95 0.90 -10 PULSE-SKIPPING FORCED CONTINUOUS Burst Mode OPERATION -20 -30 105 130 3859 G24 SS CURRENT (A) MAXIMUM CURRENT SENSE VOLTAGE (mV) MAXIMUM CURRENT SENSE VOLTAGE (mV) 80 Maximum Current Sense Threshold vs ITH Voltage 70 0 100 3859 G23 Maximum Current Sense Threshold vs Duty Cycle 0 120 20 VOUT = 3.3V 3859 G22 50 140 40 0 -45 -20 40 130 160 100 80 105 SENSE3+ PIN 180 200 5 10 15 20 25 30 35 VSENSE COMMON MODE VOLTAGE (V) 5 30 55 80 TEMPERATURE (C) -20 Boost SENSE Pin Total Input Current vs Temperature SENSE CURRENT (A) SENSE CURRENT (A) SENSE CURRENT (A) 300 EXTVCC FALLING 4.4 3859 G21 700 0 4.6 200 800 SENSE1, 2 PINS 400 EXTVCC RISING 4.8 4.0 -45 20 40 60 80 100 120 140 160 180 200 LOAD CURRENT (mA) 900 500 0 5.0 Buck SENSE Pins Total Input Current vs Temperature 800 200 5.2 3859 G20 SENSE Pins Total Input Current vs VSENSE Voltage 600 INTVCC 5.4 4.2 3859 G19 700 5.6 0 0.2 0.4 0.6 0.8 ITH (V) 1 1.2 1.4 3859 G26 0.85 0.80 -45 -20 5 30 55 80 TEMPERATURE (C) 105 130 3859 G27 3859fa 9 LTC3859 TYPICAL PERFORMANCE CHARACTERISTICS Shutdown Current vs Input Voltage Shutdown Current vs Temperature Quiescent Current vs Temperature 25 22 100 18 16 14 12 90 20 QUIESCENT CURRENT (A) SHUTDOWN CURRENT (A) SHUTDOWN CURRENT (A) 20 15 10 5 0 -20 5 30 55 80 TEMPERATURE (C) 105 130 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 -20 5 30 55 80 TEMPERATURE (C) 105 130 3859 G30 Undervoltage Lockout Threshold vs Temperature 600 4.4 4.3 FREQ = INTVCC 550 RISING 4.2 INTVCC VOLTAGE (V) FREQUENCY (kHz) 500 450 400 FREQ = GND 4.1 4.0 3.9 FALLING 3.8 3.7 3.6 350 3.5 0 300 -45 100 200 300 400 500 600 700 800 FEEDBACK VOLTAGE (mV) -20 5 30 55 80 TEMPERATURE (C) 105 3859 G31 100 CHARGE PUMP CHARGING CURRENT (A) 1.40 RUN2,3 RISING RUN1 RISING 1.25 1.20 1.15 RUN2,3 FALLING RUN1 FALLING 1.10 1.05 1.00 -45 -20 5 30 55 80 TEMPERATURE (C) 105 130 3859 G34 5 30 55 80 TEMPERATURE (C) 105 90 Charge Pump Charging Current vs Switch Voltage 100 VBOOST3 = 16V VSW3 = 12V 80 70 -45C 25C 60 50 40 130C 30 20 10 0 100 200 300 400 500 600 700 OPERATING FREQUENCY (kHz) 130 3859 G33 Charge Pump Charging Current vs Operating Frequency 1.35 -20 3859 G32 Shutdown (RUN) Threshold vs Temperature 1.30 3.4 -45 130 CHARGE PUMP CHARGING CURRENT (A) MAXIMUM CURRENT SENSE VOLTAGE (mV) ONE CHANNEL ON 40 -45 40 Oscillator Frequency vs Temperature Buck Foldback Current Limit RUN PIN VOLTAGE (V) 60 3859 G29 3859 G28 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 70 50 10 8 -45 ALL CHANNELS ON 80 800 3859 G35 VBOOST3 - VSW3 = 4V 90 FREQ = 0V 80 70 FREQ = INTVCC 60 50 40 30 20 10 0 5 10 15 20 25 30 SWITCH VOLTAGE (V) 35 40 3859 G36 3859fa 10 LTC3859 PIN FUNCTIONS (QFN/TSSOP) FREQ (Pin 1/Pin 5): The Frequency Control Pin for the Internal VCO. Connecting the pin to GND forces the VCO to a fixed low frequency of 350kHz. Connecting the pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. Other frequencies between 50kHz and 900kHz can be programmed using a resistor between FREQ and GND. The resistor and an internal 20A source current create a voltage used by the internal oscillator to set the frequency. PLLIN/MODE (Pin 2/Pin 6): External Synchronization Input to Phase Detector and Forced Continuous Mode Input. When an external clock is applied to this pin, the phase-locked loop will force the rising TG1 signal to be synchronized with the rising edge of the external clock, and the regulators operate in forced continuous mode. When not synchronizing to an external clock, this input, which acts on all three controllers, determines how the LTC3859 operates at light loads. Pulling this pin to ground selects Burst Mode operation. An internal 100k resistor to ground also invokes Burst Mode operation when the pin is floated. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.2V and less than INTVCC - 1.3V selects pulse-skipping operation. This can be done by connecting a 100k resistor from this pin to INTVCC. SGND (Pin 8/Pin 12): Small Signal Ground common to both controllers, must be routed separately from high current grounds to the common (-) terminals of the CIN capacitors. RUN1, RUN2, RUN3 (Pins 9, 10, 11/Pins 13, 14, 15): Digital Run Control Inputs for Each Controller. Forcing RUN1 below 1.7V and RUN2/RUN3 below 1.20V shuts down that controller. Forcing all of these pins below 0.7V shuts down the entire LTC3859, reducing quiescent current to approximately 14A. OV3 (Pin 17/Pin 21): Overvoltage Open-Drain Logic Output for the Boost Regulator. OV3 is pulled to ground when the voltage on the VFB3 pin is under 110% of its set point, and becomes high impedance when VFB3 goes over 110% of its set point. INTVCC (Pin 22/Pin 26): Output of the Internal Linear Low Dropout Regulator. The driver and control circuits are powered from this voltage source. Must be decoupled to PGND with a minimum of 4.7F ceramic or tantalum capacitor. The INTVCC pin should also be connected to the DRVCC pin, and should not be used for any other purpose. EXTVCC (Pin 23/Pin 27): External Power Input to an Internal LDO Connected to INTVCC. This LDO supplies INTVCC power, bypassing the internal LDO powered from VIN whenever EXTVCC is higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 14V on this pin. VBIAS (Pin 24/Pin 28): Main Bias Input Supply Pin. A bypass capacitor should be tied between this pin and the SGND pin. BG1, BG2, BG3 (Pins 29, 21, 25/Pins 33, 25, 29): High Current Gate Drives for Bottom (Synchronous) N-Channel MOSFETs. Voltage swing at these pins is from ground to INTVCC. BOOST1, BOOST2, BOOST3 (Pins 30, 20, 26/Pins 34, 24, 30): Bootstrapped Supplies to the Top Side Floating Drivers. Capacitors are connected between the BOOST and SW pins and Schottky diodes are tied between the BOOST and INTVCC pins. Voltage swing at the BOOST pins is from INTVCC to (VIN + INTVCC). SW1, SW2, SW3 (Pins 31, 19, 28/Pins 35, 23, 32): Switch Node Connections to Inductors. TG1, TG2, TG3 (Pins 32, 18, 27/Pins 36, 22, 31): High Current Gate Drives for Top N-Channel MOSFETs. These are the outputs of floating drivers with a voltage swing equal to INTVCC superimposed on the switch node voltage SW. PGOOD1 (Pin 33/Pin 37): Open-Drain Logic Output. PGOOD1 is pulled to ground when the voltage on the VFB1 pin is not within 10% of its set point. 3859fa 11 LTC3859 PIN FUNCTIONS (QFN/TSSOP) TRACK/SS1, TRACK/SS2, SS3 (Pins 34, 16, 3/Pins 38, 20, 7): External Tracking and Soft-Start Input. For the buck channels, the LTC3859 regulates the VFB1,2 voltage to the smaller of 0.8V, or the voltage on the TRACK/SS1,2 pin. For the boost channel, the LTC3859 regulates the VFB3 voltage to the smaller of 1.2V, or the voltage on the SS3 pin. An internal 1A pull-up current source is connected to this pin. A capacitor to ground at this pin sets the ramp time to final regulated output voltage. Alternatively, a resistor divider on another voltage supply connected to the TRACK/SS pins of the buck channels allow the LTC3859 buck outputs to track the other supply during start-up. ITH1, ITH2, ITH3 (Pins 35, 15, 7/Pins 1, 19, 11): Error Amplifier Outputs and Switching Regulator Compensation Points. Each associated channel's current comparator trip point increases. VFB1, VFB2, VFB3 (Pins 36, 14, 6/Pins 2, 18, 10): Receives the remotely sensed feedback voltage for each controller from an external resistive divider across the output. SENSE1+, SENSE2+, SENSE3+ (Pins 37, 13, 4/Pins 3, 17, 8): The (+) Input to the Differential Current Comparators. The ITH pin voltage and controlled offsets between the SENSE- and SENSE+ pins in conjunction with RSENSE set the current trip threshold. For the boost channel, the SENSE3+ pin supplies current to the current comparator. SENSE1-, SENSE2-, SENSE3- (Pins 38, 12, 5/Pins 4, 16, 9): The (-) Input to the Differential Current Comparators. When SENSE1,2- for the buck channels is greater than INTVCC, then SENSE1,2- pin supplies current to the current comparator. PGND (Exposed Pad Pin 39): Driver Power Ground. Connects to the sources of bottom (synchronous) N-channel MOSFETs and the (-) terminal(s) of CIN. The exposed pad must be soldered to the PCB for rated electrical and thermal performance. 3859fa 12 4.7V EXTVCC VBIAS FREQ + - LDO LDO EN 5.4V SGND SYNC DET CLP VCO 5.4V EN 100k 20A + - + - CLK1 CLK2 INTVCC PFD 0.72V VFB1 0.88V RUN 11V SHDN RST 2(VFB) 6A CH1 0.5A CH2 + - BOT FOLDBACK SLEEP SHDN TOPON + - -+ SLOPE COMP 2.8V 0.65V Q R ICMP Q DROPOUT DET S BUCK CHANNELS 1 AND 2 3mV -+ PGOOD1 OV + - SHDN + - + EA - - IR SWITCHING LOGIC 1A 0.88V PGND BG SW TG TRACK/SS ITH VFB SENSE- SENSE+ INTVCC 0.80V TRACK/SS BOT TOP BOOST 3859 BD CSS CB DB INTVCC L RB D CC2 CC RA VIN1,2 RC RSENSE COUT CIN VOUT1,2 LTC3859 FUNCTIONAL DIAGRAM 3859fa 13 14 OV3 + - VFB3 1.32V PLLIN/MODE CLK1 RUN3 Q R 11V 0.5A SHDN + - SNSLO 1A OV + - 2mV 1.32V + - SS3 ITH3 VFB3 SENSE3+ SENSE3- PGND BG3 SW3 TG3 BOOST3 INTVCC 1.2V SS3 BOT TOP + EA - - 2V IR SWITCHING LOGIC + +- - SLEEP SHDN BOTON SNSLO + - -+ ICMP 0.425V Q S SLOPE COMP 2.8V 0.7V BOOST CHANNEL 3 3859 BD CSS CB DB INTVCC L RB CC2 CC RA VOUT3 RC RSENSE CIN COUT VIN3 LTC3859 FUNCTIONAL DIAGRAM 3859fa LTC3859 OPERATION (Refer to Functional Diagram) Main Control Loop The LTC3859 uses a constant frequency, current mode step-down architecture. The two buck controllers, channels 1 and 2, operate 180 degrees out of phase with each other. The boost controller, channel 3, operates in phase with channel 1. During normal operation, the external top MOSFET for the buck channels (the external bottom MOSFET for the boost channel) is turned on when the clock for that channel sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier EA. The error amplifier compares the output voltage feedback signal at the VFB pin, (which is generated with an external resistor divider connected across the output voltage, VOUT, to ground) to the internal 0.800V reference voltage for the bucks (1.2V reference voltage for the boost). When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. After the top MOSFET for the bucks (the bottom MOSFET for the boost) is turned off each cycle, the bottom MOSFET is turned on (the top MOSFET for the boost) until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. When the EXTVCC pin is left open or tied to a voltage less than 4.7V, the VBIAS LDO (low dropout linear regulator) supplies 5.4V from VBIAS to INTVCC. If EXTVCC is taken above 4.7V, the VBIAS LDO is turned off and an EXTVCC LDO is turned on. Once enabled, the EXTVCC LDO supplies 5.4V from EXTVCC to INTVCC. Using the EXTVCC pin allows the INTVCC power to be derived from a high efficiency external source such as one of the LTC3859 switching regulator outputs. Each top MOSFET driver is biased from the floating bootstrap capacitor CB, which normally recharges during each cycle through an external diode when the switch voltage goes low. For buck channels 1 and 2, if the buck's input voltage decreases to a voltage close to its output, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about one twelfth of the clock period every tenth cycle to allow CB to recharge. Shutdown and Start-Up (RUN1, RUN2, RUN3 and TRACK/SS1, TRACK/SS2, SS3 Pins) The three channels of the LTC3859 can be independently shut down using the RUN1, RUN2 and RUN3 pins. Pulling any of these pins below 1.19V shuts down the main control loop for that channel. Pulling all three pins below 0.7V disables all controllers and most internal circuits, including the INTVCC LDOs. In this state, the LTC3859 draws only 14A of quiescent current. Releasing a RUN pin allows a small internal current to pull up the pin to enable that controller. The RUN1 pin has a 6A pull-up current while the RUN2 and RUN3 pins have a smaller 0.5A. The 6A current on RUN1 is designed to be large enough so that the RUN1 pin can be safely floated (to always enable the controller) without worry of condensation or other small board leakage pulling the pin down. This is ideal for always-on applications where one or more controllers are enabled continuously and never shut down. Each RUN pin may also be externally pulled up or driven directly by logic. When driving a RUN pin with a low impedance source, do not exceed the absolute maximum rating of 8V. Each RUN pin has an internal 11V voltage clamp that allows the RUN pin to be connected through a resistor to a higher voltage (for example, VBIAS), so long as the maximum current in the RUN pin does not exceed 100A. The start-up of each channel's output voltage VOUT is controlled by the voltage on the TRACK/SS pin (TRACK/SS1 for channel 1, TRACK/SS2 for channel 2, SS3 for channel 3). When the voltage on the TRACK/SS pin is less than 3859fa 15 LTC3859 OPERATION the 0.8V internal reference for the bucks and the 1.2V internal reference for the boost, the LTC3859 regulates the VFB voltage to the TRACK/SS pin voltage instead of the corresponding reference voltage. This allows the TRACK/SS pin to be used to program a soft-start by connecting an external capacitor from the TRACK/SS pin to SGND. An internal 1A pull-up current charges this capacitor creating a voltage ramp on the TRACK/SS pin. As the TRACK/SS voltage rises linearly from 0V to 0.8V/1.2V (and beyond up to INTVCC), the output voltage VOUT rises smoothly from zero to its final value. Alternatively the TRACK/SS pins for buck channels 1 and 2 can be used to cause the start-up of VOUT to track that of another supply. Typically, this requires connecting to the TRACK/SS pin an external resistor divider from the other supply to ground (see the Applications Information section). Light Load Current Operation (Burst Mode Operation, Pulse-Skipping, or Continuous Conduction) (PLLIN/MODE Pin) The LTC3859 can be enabled to enter high efficiency Burst Mode operation, constant frequency pulse-skipping mode or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/ MODE pin to ground. To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulse-skipping mode, tie the PLLIN/MODE pin to a DC voltage greater than 1.2V and less than INTVCC - 1.3V. When a controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 25% of the maximum sense voltage (30% for the boost) even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier EA will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. The ITH pin is then disconnected from the output of the EA and parked at 0.450V. In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current that the LTC3859 draws. If one channel is in sleep mode and the other two are shut down, the LTC3859 draws only 55A of quiescent current. If two channels are in sleep mode and the other shut down, it draws only 65A of quiescent current. If all three controllers are enabled in sleep mode, the LTC3859 draws only 80A of quiescent. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA's output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator (IR) turns off the bottom external MOSFET (the top external MOSFET for the boost) just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous operation. In forced continuous operation or clocked by an external clock source to use the phase-locked loop (see the Frequency Selection and Phase-Locked Loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantage of lower output voltage ripple and less interference to audio circuitry. In forced continuous mode, the output ripple is independent of load current. When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC3859 operates in PWM pulse-skipping mode at light loads. In this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator ICMP may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. 3859fa 16 LTC3859 OPERATION Frequency Selection and Phase-Locked Loop (FREQ and PLLIN/MODE Pins) The selection of switching frequency is a tradeoff between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3859's controllers can be selected using the FREQ pin. If the PLLIN/MODE pin is not being driven by an external clock source, the FREQ pin can be tied to SGND, tied to INTVCC, or programmed through an external resistor. Tying FREQ to SGND selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and SGND allows the frequency to be programmed between 50kHz and 900kHz. A phase-locked loop (PLL) is available on the LTC3859 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN/MODE pin. The LTC3859's phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of controller 1's external top MOSFET to the rising edge of the synchronizing signal. Thus, the turn-on of controller 2's external top MOSFET is 180 degrees out of phase to the rising edge of the external clock source. The VCO input voltage is pre-biased to the operating frequency set by the FREQ pin before the external clock is applied. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock's to the rising edge of TG1. The ability to pre-bias the loop filter allows the PLL to lock in rapidly without deviating far from the desired frequency. The typical capture range of the LTC3859's phase-locked loop is from approximately 55kHz to 1MHz, with a guarantee over all manufacturing variations to be between 75kHz and 850kHz. In other words, the LTC3859's PLL is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. The typical input clock thresholds on the PLLIN/MODE pin are 1.6V (rising) and 1.2V (falling). Boost Controller Operation When VIN > VOUT When the input voltage to the boost channel rises above its regulated VOUT voltage, the controller can behave differently depending on the mode, inductor current and VIN voltage. In forced continuous mode, the loop works to keep the top MOSFET on continuously once VIN rises above VOUT. An internal charge pump delivers current to the boost capacitor from the BOOST3 pin to maintain a sufficiently high TG voltage. (The amount of current the charge pump can deliver is characterized by two curves in the Typical Performance Characteristics section.) In pulse-skipping mode, if VIN is between 100% and 110% of the regulated VOUT voltage, TG turns on if the inductor current rises above a certain threshold and turns off if the inductor current falls below this threshold. This threshold current is set approximately to 3% of the programmed maximum ILIM current. If the controller is programmed to Burst Mode operation under this same VIN window, then TG remains off regardless of the inductor current. If VIN rises above 110% of the regulated VOUT voltage in any mode, the controller turns on TG regardless of the inductor current. In Burst Mode operation, however, the internal charge pump turns off if the boost channel is asleep. With the charge pump off, there would be nothing to prevent the boost capacitor from discharging, resulting in an insufficient TG voltage needed to keep the top MOSFET completely on. To prevent excessive power dissipation across the body diode of the top MOSFET in this situation, the chip can be switched over to forced continuous mode to enable the charge pump, or a Schottky diode can also be placed in parallel with the top MOSFET. Boost Controller at Low SENSE Pin Common Voltage The current comparator of the boost controller is powered directly from the SENSE3+ pin and can operate to voltages as low as 2.5V. Since this is lower than the VBIAS UVLO of the chip, VBIAS can be connected to the output of the boost controller, as illustrated in the typical application circuit in Figure 12. This allows the boost controller to handle input voltage transients down to 2.5V while maintaining output voltage regulation. If the SENSE3+ rises back above 2.5V, the SS3 pin will be released initiating a new soft-start sequence. 3859fa 17 LTC3859 OPERATION Buck Controller Output Overvoltage Protection Buck Foldback Current The two buck channels have an overvoltage comparator that guards against transient overshoots as well as other more serious conditions that may overvoltage their outputs. When the VFB1,2 pin rises by more than 10% above its regulation point of 0.800V, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. When the buck output voltage falls to less than 70% of its nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to the severity of the overcurrent or short-circuit condition. Foldback current limiting is disabled during the soft-start interval (as long as the VFB voltage is keeping up with the TRACK/SS1,2 voltage). There is no foldback current limiting for the boost channel. Channel 1 Power Good (PGOOD1) Channel 1 has a PGOOD1 pin that is connected to an open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD1 pin low when the VFB1 pin voltage is not within 10% of the 0.8V reference voltage for the buck channel. The PGOOD1 pin is also pulled low when the RUN1 pin is low (shut down). When the VFB1 pin voltage is within the 10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V. Boost Overvoltage Indicator (OV3) The OV3 pin is an overvoltage indicator that signals whether the output voltage of the channel 3 boost controller goes over its programmed regulated voltage. The pin is connected to an open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the OV3 pin low when the VFB3 pin voltage is less than 110% of the 1.2V reference voltage for the boost channel. The OV3 pin is also pulled low when the RUN3 pin is low (shut down). When the VFB3 pin voltage goes higher than 110% of the 1.2V reference, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V. THEORY AND BENEFITS OF 2-PHASE OPERATION Why the need for 2-phase operation? Up until the 2-phase family, constant-frequency dual switching regulators operated both channels in phase (i.e., single-phase operation). This means that both switches turned on at the same time, causing current pulses of up to twice the amplitude of those for one regulator to be drawn from the input capacitor and battery. These large amplitude current pulses increased the total RMS current flowing from the input capacitor, requiring the use of more expensive input capacitors and increasing both EMI and losses in the input capacitor and battery. With 2-phase operation, the two buck controllers of the LTC3859 are operated 180 degrees out of phase. This effectively interleaves the current pulses drawn by the switches, greatly reducing the overlap time where they add together. The result is a significant reduction in total RMS input current, which in turn allows less expensive input capacitors to be used, reduces shielding requirements for EMI and improves real world operating efficiency. 3859fa 18 LTC3859 OPERATION 5V SWITCH 20V/DIV 3.3V SWITCH 20V/DIV INPUT CURRENT 5A/DIV INPUT VOLTAGE 500mV/DIV IIN(MEAS) = 2.53ARMS IIN(MEAS) = 1.55ARMS 3859 F01a (a) 3859 F01b (b) Figure 1. Input Waveforms Comparing Single-Phase (a) and 2-Phase (b) Operation for Dual Switching Regulators Converting 12V to 5V and 3.3V at 3A Each. The Reduced Input Ripple with the 2-Phase Regulator Allows Less Expensive Input Capacitors, Reduces Shielding Requirements for EMI and Improves Efficiency Of course, the improvement afforded by 2-phase operation is a function of the dual switching regulator's relative duty cycles which, in turn, are dependent upon the input voltage VIN (Duty Cycle = VOUT/VIN). Figure 2 shows how the RMS input current varies for single-phase and 2-phase operation for 3.3V and 5V regulators over a wide input voltage range. It can readily be seen that the advantages of 2-phase operation are not just limited to a narrow operating range, for most applications is that 2-phase operation will reduce the input capacitor requirement to that for just one channel operating at maximum current and 50% duty cycle. The schematic on the first page is a basic LTC3859 application circuit. External component selection is driven by the load requirement, and begins with the selection of RSENSE and the inductor value. Next, the power MOSFETs are selected. Finally, CIN and COUT are selected. 3.0 SINGLE PHASE DUAL CONTROLLER 2.5 INPUT RMS CURRENT (A) Figure 1 compares the input waveforms for a representative single-phase dual switching regulator to the 2-phase dual buck controllers of the LTC3859. An actual measurement of the RMS input current under these conditions shows that 2-phase operation dropped the input current from 2.53ARMS to 1.55ARMS. While this is an impressive reduction in itself, remember that the power losses are proportional to IRMS2, meaning that the actual power wasted is reduced by a factor of 2.66. The reduced input ripple voltage also means less power is lost in the input power path, which could include batteries, switches, trace/connector resistances and protection circuitry. Improvements in both conducted and radiated EMI also directly accrue as a result of the reduced RMS input current and voltage. 2.0 1.5 2-PHASE DUAL CONTROLLER 1.0 0.5 0 VO1 = 5V/3A VO2 = 3.3V/3A 0 10 20 30 INPUT VOLTAGE (V) 40 3859 F02 Figure 2. RMS Input Current Comparison 3859fa 19 LTC3859 APPLICATIONS INFORMATION The Typical Application on the first page is a basic LTC3859 application circuit. LTC3859 can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption, and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs and Schottky diodes are selected. Finally, input and output capacitors are selected. on the SENSE3- pin allows the current comparator to be used in inductor DCR sensing. Filter components mutual to the sense lines should be placed close to the LTC3859, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 3). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If DCR sensing is used (Figure 4b), sense resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. TO SENSE FILTER NEXT TO THE CONTROLLER SENSE+ and SENSE- Pins The SENSE+ and SENSE- pins are the inputs to the current comparators. Buck Controllers (SENSE1+/SENSE1-,SENSE2+/SENSE2-): The common mode voltage range on these pins is 0V to 28V (absolute maximum), enabling the LTC3859 to regulate buck output voltages up to a nominal 24V (allowing margin for tolerances and transients). The SENSE+ pin is high impedance over the full common mode range, drawing at most 1A. This high impedance allows the current comparators to be used in inductor DCR sensing. The impedance of the SENSE- pin changes depending on the common mode voltage. When SENSE- is less than INTVCC -0.5V, a small current of less than 1A flows out of the pin. When SENSE- is above INTVCC +0.5V, a higher current (700A) flows into the pin. Between INTVCC -0.5V and INTVCC +0.5V, the current transitions from the smaller current to the higher current. Boost Controller (SENSE3+/SENSE3-): The common mode input range for these pins is 2.5V to 38V, allowing the boost converter to operate from inputs over this full range. The SENSE3+ pin also provides power to the current comparator and draws about 170A during normal operation (when not shut down or asleep in Burst Mode operation). There is a small bias current of less than 1A that flows out of the SENSE3- pin. This high impedance CURRENT FLOW 3859 F03 INDUCTOR OR RSENSE Figure 3. Sense Lines Placement with Inductor or Sense Resistor Low Value Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 4a. RSENSE is chosen based on the required output current. The current comparators have a maximum threshold VSENSE(MAX) of 50mV. The current comparator threshold sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, DIL. To calculate the sense resistor value, use the equation: VSENSE(MAX) RSENSE = I IMAX + L 2 When using the buck controllers in very low dropout conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for buck regulators operating at greater than 50% duty factor. A curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak output current level depending upon the operating duty factor. 3859fa 20 LTC3859 APPLICATIONS INFORMATION VIN1,2 (VOUT3) INTVCC BOOST TG LTC3859 RSENSE SW VOUT1,2 (VIN3) BG SENSE1,2+ (SENSE3-) SENSE1, 2- (SENSE3+) CAP PLACED NEAR SENSE PINS SGND 3859 F04a 4a. Using a Resistor to Sense Current VIN1,2 (VOUT3) INTVCC BOOST INDUCTOR TG LTC3859 L DCR SW VOUT1,2 (VIN3) If the external R1||R2 * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers' data sheets for detailed information. Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: VSENSE(MAX) RSENSE(EQUIV) = I IMAX + L 2 To ensure that the application will deliver full load current over the full operating temperature range, determine RSENSE(EQUIV), keeping in mind that the maximum current sense threshold (VSENSE(MAX)) for the LTC3859 is fixed at 50mV. BG R1 SENSE1, 2+ (SENSE3-) SENSE1, 2- (SENSE3+) C1* R2 SGND 3859 F04b *PLACE C1 NEAR SENSE PINS (R1||R2) * C1 = L/DCR RSENSE(EQ) = DCR(R2/(R1+R2)) 4b. Using the Inductor DCR to Sense Current Figure 4. Current Sensing Methods Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3859 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 4b. The DCR of the inductor represents the small amount of DC winding resistance of the copper, which can be less than 1m for today's low value, high current inductors. In a high current application requiring such an inductor, conduction loss through a sense resistor would cost several points of efficiency compared to DCR sensing. Next, determine the DCR of the inductor. Where provided, use the manufacturer's maximum value, usually given at 20C. Increase this value to account for the temperature coefficient of resistance, which is approximately 0.4%/C. A conservative value for TL(MAX) is 100C. To scale the maximum inductor DCR to the desired sense resistor value, use the divider ratio: RSENSE(EQUIV) RD = DCRMAX at TL(MAX) C1 is usually selected to be in the range of 0.1F to 0.47F. This forces R1||R2 to around 2k, reducing error that might have been caused by the SENSE+ pin's 1A current. The equivalent resistance R1||R2 is scaled to the room temperature inductance and maximum DCR: L R1(R2 = (DCR at 20C) * C1 The sense resistor values are: R1= R1* RD R1(R2 ; R2 = RD 1- RD 3859fa 21 LTC3859 APPLICATIONS INFORMATION The maximum power loss in R1 is related to duty cycle. For the buck controllers, the maximum power loss will occur in continuous mode at the maximum input voltage: PLOSS R1= (VIN(MAX) - VOUT ) * VOUT R1 For the boost controller, the maximum power loss in R1 will occur in continuous mode at VIN = 1/2*VOUT : PLOSS R1= (VOUT(MAX) - VIN ) * VIN R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current DIL decreases with higher inductance or frequency. For the buck controllers, DIL increases with higher VIN: V 1 IL = VOUT 1- OUT (f)(L) VIN For the boost controller, the inductor ripple current DIL increases with higher VOUT: IL = V 1 VIN 1- IN (f)(L) VOUT Accepting larger values of DIL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is DIL = 0.3(IMAX). The maximum DIL occurs at the maximum input voltage for the bucks and VIN = 1/2*VOUT for the boost. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 25% of the current limit (30% for the boost) determined by RSENSE. Lower inductor values (higher DIL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates "hard," which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET and Schottky Diode (Optional) Selection Two external power MOSFETs must be selected for each controller in the LTC3859: one N-channel MOSFET for the top switch (main switch for the buck, synchronous for the boost), and one N-channel MOSFET for the bottom switch (main switch for the boost, synchronous for the buck). 3859fa 22 LTC3859 APPLICATIONS INFORMATION The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5.4V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the on-resistance RDS(ON), Miller capacitance CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: V Buck Main Switch Duty Cycle = OUT VIN V -V Buck Sync Switch Duty Cycle = IN OUT VIN V -V Boost Main Switch Duty Cycle = OUT IN VOUT Boost Sync Switch Duty Cycle = VIN VOUT The MOSFET power dissipations at maximum output current are given by: PMAIN _ BUCK = ( VOUT I VIN OUT(MAX) ) (1+ )R 2 DS(ON) + IOUT(MAX) (VIN )2 (RDR )(CMILLER ) * 2 1 1 + (f) VINTVCC - VTHMIN VTHMIN V -V PSYNC _ BUCK = IN OUT IOUT(MAX) VIN ( ) (1+ )R 2 DS(ON) PMAIN _ BOOST = ( VOUT - VIN ) VOUT VIN V2 (1+ )RDS(ON) + OUT VIN 2 (IOUT(MAX) ) 2 * IOUT(MAX) * 2 1 1 + (f) - V V THMIN THMIN INTVCC 2 VIN I PSYNC _ BOOST = (1+ )RDS(ON) VOUT OUT(MAX) (RDR )(CMILLER ) * V ( ) where z is the temperature dependency of RDS(ON) and RDR (approximately 2) is the effective driver resistance at the MOSFET's Miller threshold voltage. VTHMIN is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the main N-channel equations for the buck and boost controllers include an additional term for transition losses, which are highest at high input voltages for the bucks and low input voltages for the boost. For VIN < 20V (high VIN for the boost) the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V (low VIN for the boost) the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses for the buck controllers are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. The synchronous MOSFET losses for the boost controller are greatest when the input voltage approaches the output voltage or during an overvoltage event when the synchronous switch is on 100% of the period. The term (1+ z) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but z = 0.005/C can be used as an approximation for low voltage MOSFETs. The optional Schottky diodes D4, D5, and D6 shown in Figure 13 conduct during the dead-time between the conduction of the two power MOSFETs. This prevents the body diode of the synchronous MOSFET from turning on, storing charge during the dead-time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally 3859fa 23 LTC3859 APPLICATIONS INFORMATION a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. Boost CIN, COUT Selection The input ripple current in a boost converter is relatively low (compared with the output ripple current), because this current is continuous. The boost input capacitor CIN voltage rating should comfortably exceed the maximum input voltage. Although ceramic capacitors can be relatively tolerant of overvoltage conditions, aluminum electrolytic capacitors are not. Be sure to characterize the input voltage for any possible overvoltage transients that could apply excess stress to the input capacitors. The value of CIN is a function of the source impedance, and in general, the higher the source impedance, the higher the required input capacitance. The required amount of input capacitance is also greatly affected by the duty cycle. High output current applications that also experience high duty cycles can place great demands on the input supply, both in terms of DC current and ripple current. In a boost converter, the output has a discontinuous current, so COUT must be capable of reducing the output voltage ripple. The effects of ESR (equivalent series resistance) and the bulk capacitance must be considered when choosing the right capacitor for a given output ripple voltage. The steady ripple due to charging and discharging the bulk capacitance is given by: Ripple = ( ) IOUT(MAX) * VOUT - VIN(MIN) V C OUT * VOUT * f where COUT is the output filter capacitor. The steady ripple due to the voltage drop across the ESR is given by: DVESR = IL(MAX) * ESR Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient. Capacitors are now available with low ESR and high ripple current ratings such as OS-CON and POSCAP. Buck CIN, COUT Selection The selection of CIN for the two buck controllers is simplified by the 2-phase architecture and its impact on the worstcase RMS current drawn through the input network (battery/fuse/capacitor). It can be shown that the worst-case capacitor RMS current occurs when only one controller is operating. The controller with the highest (VOUT)(IOUT) product needs to be used in the formula shown in Equation (1) to determine the maximum RMS capacitor current requirement. Increasing the output current drawn from the other controller will actually decrease the input RMS ripple current from its maximum value. The out-of-phase technique typically reduces the input capacitor's RMS ripple current by a factor of 30% to 70% when compared to a single phase power supply solution. In continuous mode, the source current of the top MOSFET is a square wave of duty cycle (VOUT)/(VIN). To prevent large voltage transients, a low ESR capacitor sized for the maximum RMS current of one channel must be used. The maximum RMS capacitor current is given by: CIN Required IRMS 1/ 2 IMAX ( VOUT ) ( VIN - VOUT ) (1) VIN This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may be paralleled to meet size or height requirements in the design. Due to the high operating frequency of the LTC3859, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. The benefit of the LTC3859 2-phase operation can be calculated by using Equation (1) for the higher power controller and then calculating the loss that would have resulted if both controller channels switched on at the same time. 3859fa 24 LTC3859 APPLICATIONS INFORMATION The total RMS power lost is lower when both controllers are operating due to the reduced overlap of current pulses required through the input capacitor's ESR. This is why the input capacitor's requirement calculated above for the worst-case controller is adequate for the dual controller design. Also, the input protection fuse resistance, battery resistance, and PC board trace resistance losses are also reduced due to the reduced peak currents in a 2-phase system. The overall benefit of a multiphase design will only be fully realized when the source impedance of the power supply/battery is included in the efficiency testing. The drains of the top MOSFETs should be placed within 1cm of each other and share a common CIN (s). Separating the drains and CIN may produce undesirable voltage and current resonances at VIN. A small (0.1F to 1F) bypass capacitor between the chip VIN pin and ground, placed close to the LTC3859, is also suggested. A small (1 to 10) resistor placed between CIN (C1) and the VIN pin provides further isolation between the two channels. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering. The output ripple (DVOUT) is approximated by: 1 VOUT IL ESR + 8fCOUT VOUT RB 1/3 LTC3859 CFF VFB RA 3859 F05 Figure 5. Setting Output Voltage To improve the frequency response, a feedforward capacitor, CFF, may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. Tracking and Soft-Start (TRACK/SS1, TRACK/SS2, SS3 Pins) The start-up of each VOUT is controlled by the voltage on the respective TRACK/SS pin (TRACK/SS1 for channel 1, TRACK/SS2 for channel 2, SS3 for channel 3). When the voltage on the TRACK/SS pin is less than the internal 0.8V reference (1.2V reference for the boost channel), the LTC3859 regulates the VFB pin voltage to the voltage on the TRACK/SS pin instead of the internal reference. Likewise, the TRACK/SS pin for the buck channels can be used to program an external soft-start function or to allow VOUT to track another supply during start-up. 1/3 LTC3859 TRACK/SS where f is the operating frequency, COUT is the output capacitance and DIL is the ripple current in the inductor. The output ripple is highest at maximum input voltage since DIL increases with input voltage. Setting Output Voltage The LTC3859 output voltages are each set by an external feedback resistor divider carefully placed across the output, as shown in Figure 5. The regulated output voltages are determined by: R VOUT, BUCK = 0.8V 1+ B RA R VOUT, BOOST = 1.2V 1+ B RA CSS SGND 3859 F06 Figure 6. Using the TRACK/SS Pin to Program Soft-Start Soft-start is enabled by simply connecting a capacitor from the TRACK/SS pin to ground, as shown in Figure 6. An internal 1A current source charges the capacitor, providing a linear ramping voltage at the TRACK/SS pin. The LTC3859 will regulate the VFB pin (and hence VOUT) according to the voltage on the TRACK/SS pin, allowing VOUT to rise smoothly from 0V to its final regulated value. The total soft-start time will be approximately: 0.8V t SS _ BUCK = CSS * 1A 1.2V t SS _ BOOST = CSS * 1A 3859fa 25 LTC3859 APPLICATIONS INFORMATION VX(MASTER) VOUT(SLAVE) TIME OUTPUT (VOUT) OUTPUT (VOUT) VX(MASTER) VOUT(SLAVE) TIME 3859 F07a 7a. Coincident Tracking 3859 F07b 7b. Radiometric Tracking Figure 7. Two Different Modes of Output Voltage Tracking VOUT RB LTC3859 VFB1,2 RA VX RTRACKB TRACK/SS1,2 RTRACKA 3859 F08 Figure 8. Using the TRACK/SS Pin for Tracking Alternatively, the TRACK/SS1 and TRACK/SS2 pins for the two buck controllers can be used to track two (or more) supplies during start-up, as shown qualitatively in Figures 7a and 7b. To do this, a resistor divider should be connected from the master supply (VX) to the TRACK/SS pin of the slave supply (VOUT), as shown in Figure 8. During start-up VOUT will track VX according to the ratio set by the resistor divider: + R TRACKB R RA VX = * TRACKA VOUT R TRACKA R A + RB For coincident tracking (VOUT = VX during start-up), RA = RTRACKA RB = RTRACKB INTVCC Regulators The LTC3859 features two separate internal P-channel low dropout linear regulators (LDO) that supply power at the INTVCC pin from either the VBIAS supply pin or the EXTVCC pin depending on the connection of the EXTVCC pin. INTVCC powers the gate drivers and much of the LTC3859's internal circuitry. The VBIAS LDO and the EXTVCC LDO regulate INTVCC to 5.4V. Each of these can supply a peak current of 50mA and must be bypassed to ground with a minimum of 4.7F ceramic capacitor. No matter what type of bulk capacitor is used, an additional 1F ceramic capacitor placed directly adjacent to the INTVCC and PGND IC pins is highly recommended. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3859 to be exceeded. The INTVCC current, which is dominated by the gate charge current, may be supplied by either the VBIAS LDO or the EXTVCC LDO. When the voltage on the EXTVCC pin is less than 4.7V, the VBIAS LDO is enabled. Power dissipation for the IC in this case is highest and is equal to VBIAS * IINTVCC. The gate charge current is dependent on operating frequency as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 2 of the Electrical Characteristics. For example, the LTC3859 INTVCC current is limited to less than 40mA from a 40V supply when not using the EXTVCC supply at a 70C ambient temperature in the QFN package: TJ = 70C + (40mA)(40V)(34C/W) = 125C 3859fa 26 LTC3859 APPLICATIONS INFORMATION To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode (PLLIN/MODE = INTVCC) at maximum VIN. 2. EXTVCC connected directly to the output voltage of one of the buck regulators. This is the normal connection for a 5V to 14V regulator and provides the highest efficiency. When the voltage applied to EXTVCC rises above 4.7V, the VBIAS LDO is turned off and the EXTVCC LDO is enabled. The EXTVCC LDO remains on as long as the voltage applied to EXTVCC remains above 4.5V. The EXTVCC LDO attempts to regulate the INTVCC voltage to 5.4V, so while EXTVCC is less than 5.4V, the LDO is in dropout and the INTVCC voltage is approximately equal to EXTVCC. When EXTVCC is greater than 5.4V, up to an absolute maximum of 14V, INTVCC is regulated to 5.4V. 3. EXTVCC connected to an external supply. If an external supply is available in the 5V to 14V range, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. Ensure that EXTVCC < VIN. Using the EXTVCC LDO allows the MOSFET driver and control power to be derived from one of the LTC3859's switching regulator outputs (4.7V VOUT 14V) during normal operation and from the VBIAS LDO when the output is out of regulation (e.g., startup, short-circuit). If more current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the EXTVCC and INTVCC pins. In this case, do not apply more than 6V to the EXTVCC pin and make sure than EXTVCC VBIAS. Significant efficiency and thermal gains can be realized by powering INTVCC from the buck output, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/(Switcher Efficiency). For 5V to 14V regulator outputs, this means connecting the EXTVCC pin directly to VOUT. Tying the EXTVCC pin to a 8.5V supply reduces the junction temperature in the previous example from 125C to: TJ = 70C + (40mA)(8.5V)(34C/W) = 82C However, for 3.3V and other low voltage outputs, additional circuitry is required to derive INTVCC power from the output. The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 5.4V regulator resulting in an efficiency penalty of up to 10% at high input voltages. 4. EXTVCC connected to an output-derived boost network off one of the buck regulators. For 3.3V and other low voltage buck regulators, efficiency gains can still be realized by connecting EXTVCC to an output-derived voltage that has been boosted to greater than 4.7V. This can be done with the capacitive charge pump shown in Figure 9. Ensure that EXTVCC < VIN. VIN1,2 C1 LTC3859 BAT85 BAT85 MTOP BAT85 TG EXTVCC L RSENSE VOUT1,2 SW MBOT BG PGND 3859 F09 Figure 9. Capacitive Charge Pump for EXTVCC Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors CB connected to the BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though external diode DB from INTVCC when the SW pin is low. When one of the topside MOSFETs is to be turned on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN for the buck channels (VOUT for the boost channel) and the BOOST pin follows. With the topside MOSFET 3859fa 27 LTC3859 APPLICATIONS INFORMATION on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC (VBOOST = VOUT + VINTVCC for the boost controller). The value of the boost capacitor CB needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX) for the buck channels and VOUT(MAX) for the boost channel. When adjusting the gate drive level, the final arbiter is the total input current for the regulator. If a change is made and the input current decreases, then the efficiency has improved. If there is no change in input current, then there is no change in efficiency. The topside MOSFET driver for the boost channel includes an internal charge pump that delivers current to the bootstrap capacitor from the BOOST3 pin. This charge current maintains the bias voltage required to keep the top MOSFET on continuously during dropout/overvoltage conditions. The Schottky diode selected for the boost topside driver should have a reverse leakage less than the available output current the charge pump can supply under all operating conditions. Curves displaying the available charge pump current under different operating conditions can be found in the Typical Performance Characteristics section. Fault Conditions: Buck Current Limit and Current Foldback The LTC3859 includes current foldback for the buck channels to help limit load current when the output is shorted to ground. If the buck output falls below 70% of its nominal output level, then the maximum sense voltage is progressively lowered from 100% to 40% of its maximum selected value. Under short-circuit conditions with very low duty cycles, the buck channel will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The short-circuit ripple current is determined by the minimum on-time tON(MIN) of the LTC3859 (95ns), the input voltage and inductor value: DIL(SC) = tON(MIN) (VIN/L) The resulting average short-circuit current is: 1 ISC = 40% *ILIM(MAX) - IL(SC) 2 Fault Conditions: Buck Overvoltage Protection (Crowbar) The overvoltage crowbar is designed to blow a system input fuse when the output voltage of the one of the buck regulators rises much higher than nominal levels. The crowbar causes huge currents to flow, that blow the fuse to protect against a shorted top MOSFET if the short occurs while the controller is operating. A comparator monitors the buck output for overvoltage conditions. The comparator detects faults greater than 10% above the nominal output voltage. When this condition is sensed, the top MOSFET of the buck controller is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. The bottom MOSFET remains on continuously for as long as the overvoltage condition persists; if VOUT returns to a safe level, normal operation automatically resumes. A shorted top MOSFET for the buck channel will result in a high current condition which will open the system fuse. The switching regulator will regulate properly with a leaky top MOSFET by altering the duty cycle to accommodate the leakage. Fault Conditions: Over Temperature Protection At higher temperatures, or in cases where the internal power dissipation causes excessive self heating on chip (such as INTVCC short to ground), the over temperature shutdown circuitry will shut down the LTC3859. When the junction temperature exceeds approximately 170C, the over temperature circuitry disables the INTVCC LDO, causing the INTVCC supply to collapse and effectively shutting down the entire LTC3859 chip. Once the junction temperature drops back to approximately 155C, the INTVCC LDO turns back on. Long term overstress (TJ > 125C) should be avoided as it can degrade the performance or shorten the life of the part. Phase-Locked Loop and Frequency Synchronization The LTC3859 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a lowpass filter, and a voltage-controlled oscillator (VCO). This allows the turn-on of the top MOSFET of controller 1 to be locked to the rising edge of an external clock signal applied to the 3859fa 28 LTC3859 APPLICATIONS INFORMATION at a frequency correspond to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase-lock and synchronization. Although it is not required that the free-running frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. 1000 900 FREQUENCY (kHz) 800 700 600 500 400 300 Table 1 summarizes the different states in which the FREQ pin can be used. 200 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (k) 3859 F10 Figure 10. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin PLLIN/MODE pin. The turn-on of controller 2's top MOSFET is thus 180 degrees out of phase with the external clock. The phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. If the external clock frequency is greater than the internal oscillator's frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP, holds the voltage at the VCO input. Note that the LTC3859 can only be synchronized to an external clock whose frequency is within range of the LTC3859's internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. Typically, the external clock (on PLLIN/MODE pin) input high threshold is 1.6V, while the input low threshold is 1.2V. Rapid phase-locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO's input voltage is prebiased Table 1 FREQ PIN PLLIN/MODE PIN FREQUENCY 0V DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor to SGND DC Voltage 50kHz to 900kHz Any of the Above External Clock Phase-Locked to External Clock Minimum On-Time Considerations Minimum on-time tON(MIN) is the smallest time duration that the LTC3859 is capable of turning on the top MOSFET (bottom MOSFET for the boost controller). It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that V tON(MIN)_ BUCK < OUT VIN (f) V -V tON(MIN)_ BOOST < OUT IN VOUT (f) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. The minimum on-time for the LTC3859 is approximately 95ns for the bucks and 120ns for the boost. However, as the peak sense voltage decreases the minimum on-time gradually increases up to about 130ns. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. 3859fa 29 LTC3859 APPLICATIONS INFORMATION Efficiency Considerations Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3859 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) Topside MOSFET transition losses. RSENSE, but is "chopped" between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON) = 30m, RL = 50m, RSENSE = 10m and RESR = 40m (sum of both input and output capacitance losses), then the total resistance is 130m. This results in losses ranging from 3% to 13% as the output current increases from 1A to 5A for a 5V output, or a 4% to 20% loss for a 3.3V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 4. Transition losses apply only to the top MOSFET(s) (bottom MOSFET for the boost), and become significant only when operating at high input voltages (typically 15V or greater). Transition losses can be estimated from: 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. Transition Loss = (1.7)VIN2 * IO(MAX) * CRSS * f The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% - (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Supplying INTVCC from an output-derived source power through EXTVCC will scale the VIN current required for the driver and control circuits by a factor of (Duty Cycle)/(Efficiency). For example, in a 20V to 5V application, 10mA of INTVCC current results in approximately 2.5mA of VIN current. This reduces the mid-current loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 3. I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor, and input and output capacitor ESR. In continuous mode the average output current flows through L and Other hidden losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these "system" level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20F to 40F of capacitance having a maximum of 20m to 50m of ESR. The LTC3859 2-phase architecture typically halves this input capacitance requirement over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an 3859fa 30 LTC3859 APPLICATIONS INFORMATION amount equal to DILOAD(ESR), where ESR is the effective series resistance of COUT. DILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed loop response test point. The DC step, rise time and settling at this test point truly reflects the closed loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in Figure 16 will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. A second, more severe transient is caused by switching in loads with large (>1F) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 * CLOAD. Thus a 10F capacitor would require a 250s rise time, limiting the charging current to about 200mA. Buck Design Example As a design example for one of the buck channels channel, assume VIN = 12V(NOMINAL), VIN = 22V(MAX), VOUT = 3.3V, IMAX = 6A, VSENSE(MAX) = 50mV, and f = 350kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the FREQ pin to GND, generating 350kHz operation. The minimum inductance for 30% ripple current is: IL = VOUT VOUT 1- (f)(L) VIN(NOMINAL) A 3.9H inductor will produce 29% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 6.88A. Increasing the ripple current will also help ensure that the minimum on-time of 95ns is not violated. The minimum on-time occurs at maximum VIN: VOUT 3.3V tON(MIN) = = = 429ns VIN(MAX)(f) 22V(350kHz) 3859fa 31 LTC3859 APPLICATIONS INFORMATION The RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (43mV): RSENSE 43mV = 0.006 6.88A Choosing 1% resistors: RA = 25k and RB = 80.6k yields an output voltage of 3.33V. The power dissipation on the top side MOSFET can be easily estimated. Choosing a Fairchild FDS6982S dual MOSFET results in: RDS(ON) = 0.035/0.022, CMILLER = 215pF. At maximum input voltage with T(estimated) = 50C: 3.3V PMAIN = (6A)2 {1+ (0.005)(50 C - 25 C)} 22V 5A (0.035) + (22V)2 6 (2.5)(215pF) * 2 1 1 + (350kHz) = 433mW 5V - 2.3V 2.3V A short-circuit to ground will result in a folded back current of: 20 mV 1 95ns(22V) ISC = - = 3.07A 0.006 2 3.9H with a typical value of RDS(ON) and z = (0.005/C)(25C) = 0.125. The resulting power dissipated in the bottom MOSFET is: PSYNC = (2.23A)2 (1.125)(0.022) = 233mW which is less than under full-load conditions. The input capacitor to the buck regulator CIN is chosen for an RMS current rating of at least 3A at temperature assuming only this channel is on. COUT is chosen with an ESR of 0.02 for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: VORIPPLE = RESR (DIL) = 0.02(1.75A) = 35mVP-P PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 11. Figure 12 illustrates the current waveforms present in the various branches of the 2-phase synchronous buck regulators operating in the continuous mode. Check the following in your layout: 1. Are the top N-channel MOSFETs MTOP1 and MTOP2 located within 1cm of each other with a common drain connection at CIN? Do not attempt to split the input decoupling for the two channels as it can cause a large resonant loop. 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (-) terminals. The path formed by the top N-channel MOSFET, Schottky diode and the CIN capacitor should have short leads and PC trace lengths. The output capacitor (-) terminals should be connected as close as possible to the (-) terminals of the input capacitor by placing the capacitors next to each other and away from the Schottky loop described above. 3. Do the LTC3859 VFB pins' resistive dividers connect to the (+) terminals of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. Are the SENSE- and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE- should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the sense resistor. 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pins? This capacitor carries the MOSFET drivers' current peaks. An additional 1F ceramic capacitor placed immediately next to the INTVCC and PGND pins can help improve noise performance substantially. 3859fa 32 LTC3859 APPLICATIONS INFORMATION 6. Keep the switching nodes (SW1, SW2, SW3), top gate nodes (TG1, TG2, TG3), and boost nodes (BOOST1, BOOST2, BOOST3) away from sensitive small-signal nodes, especially from the opposites channel's voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and therefore should be kept on the output side of the LTC3859 and occupy minimum PC trace area. 7. Use a modified star ground technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC. PC Board Layout Debugging Start with one controller on at a time. It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold--typically 25% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Only after each controller is checked for its individual performance should both controllers be turned on at the same time. A particularly difficult region of operation is when one controller channel is nearing its current comparator trip point when the other channel is turning on its top MOSFET. This occurs around 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. An embarrassing problem, which can be missed in an otherwise properly working switching regulator, results when the current sensing leads are hooked up backwards. The output voltage under this improper hookup will still be maintained but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor--don't worry, the regulator will still maintain control of the output voltage. 3859fa 33 LTC3859 APPLICATIONS INFORMATION SW1 L1 D1 RSENSE1 VOUT1 COUT1 RL1 VIN RIN CIN SW2 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. D2 L2 RSENSE2 VOUT2 COUT2 RL2 3859 F11 Figure 11. Branch Current Waveforms for Bucks 3859fa 34 LTC3859 TYPICAL APPLICATIONS VOUT1 RB1 357k OPT RA1 68.1k VFB1 LTC3859 SENSE1- C1 1nF CITH1A 100pF SENSE1+ RITH1 15k CITH1 1500pF 100k ITH1 CSS1 0.1F MTOP1 TG1 TRACK/SS1 FREQ PLLIN/MODE SW1 RUN1 RB2 649k 10pF RUN3 VFB2 CITH2 2.2nF CBIAS 10F PGND EXTVCC C2 10F INTVCC D2 TG2 CSS2 0.1F TRACK/SS2 MTOP2 CB2 0.1F BOOST2 L2 6.5H RSENSE2 8m SW2 VOUT3 RA3 68.1k COUT1 220F D1 CINT1 4.7F CITH2A 68pF VOUT1 5V 5A VBIAS RITH2 15k ITH2 RSENSE1 6m MBOT1 BG1 RUN2 RA2 68.1k L1 4.9H CB1 0.1F BOOST1 SGND VOUT2 C1 10F PGOOD1 RB3 499k OPT COUT2 68F MBOT2 BG2 VOUT2 8.5V 3A VFB3 CITH3 0.01F RITH3 3.6k CITH3A 820pF CSS3 0.1F SENSE2+ C2 1nF ITH3 SENSE2- SS3 MTOP3 TG3 SW3 OV3 MTOP1, MTOP2: BSZ097NO4LS MBOT1, MBOT2: BSZ097NO4LS MTOP3: BSC027NO4LS MBOT3: BSCO1BN04LS L1: WURTH 744314490 L2: WURTH 744314650 L3: WURTH 744325120 COUT1: SANYO 6TPB220ML COUT2: SANYO 10TPC68M CIN, COUT3: SANYO 50CE220LX D1, D2: CMDH-4E D3: BAS140W VOUT3 10V* D3 BOOST3 L3 1.2H COUT3 220F RSENSE2 2m VIN 2.5V TO 38V (START-UP ABOVE 5V) CB3 0.1F BG3 MBOT3 CIN 220F SENSE3- C3 1nF SENSE3+ 3859 F12 * VOUT3 IS 10V WHEN VIN < 10V, FOLLOWS VIN WHEN VIN > 10V Figure 12. High Efficiency Wide Input Range Dual 5V/8.5V Converter 3859fa 35 LTC3859 TYPICAL APPLICATIONS VOUT1 RB1 475k 33pF RA1 34k VFB1 LTC3859 SENSE1- C1 1nF CITH1A 100pF SENSE1+ RITH1 10k CITH1 680pF 100k ITH1 CSS1 0.1F FREQ PLLIN/MODE SW1 RUN1 RB2 215k 15pF RUN3 VFB2 CITH2 820pF COUT1 47F D1 CBIAS 10F PGND EXTVCC CINT1 4.7F CITH2A 150pF VOUT1 12V 3A VBIAS RITH2 15k ITH2 RSENSE1 9m MBOT1 BG1 RUN2 VOUT2 L1 8.8H CB1 0.1F BOOST1 SGND C2 10F INTVCC D2 TG2 CSS2 0.1F TRACK/SS2 MTOP2 CB2 0.1F BOOST2 L2 3.2H RSENSE2 6m SW2 VOUT3 RA3 68.1k MTOP1 TG1 TRACK/SS1 RA2 68.1k C1 10F PGOOD1 RB3 787k OPT COUT2 150F MBOT2 BG2 VOUT2 3.3V 5A VFB3 CITH3 0.01F RITH3 3.6k SENSE2+ C2 1nF ITH3 CITH3A 820pF SENSE2- CSS3 0.1F VOUT3 15V* D3 100k INTVCC MTOP1, MTOP2: VISHAY Si7848DP MBOT1, MBOT2: VISHAY Si7848DP MTOP3: BSC027NO4LS MBOT3: BSCO1BN04LS L1: SUMIDA CDEP105-8R8M L2: SUMIDA CDEP105-3R2M L3: WURTH 744325120 COUT1: KEMET T525D476MO16E035 COUT2: SANYO 4TPE150M CIN, COUT3: SANYO 50CE220LX D1, D2: CMDH-4E D3: BAS140W SS3 TG3 OV3 SW3 BOOST3 MTOP3 L3 1.2H COUT3 220F RSENSE2 2m VIN 2.5V TO 38V (START-UP ABOVE 5V) CB3 0.1F BG3 MBOT3 CIN 220F SENSE3- C3 1nF SENSE3+ 3859 F13 * VOUT3 IS 15V WHEN VIN < 15V, FOLLOWS VIN WHEN VIN > 15V Figure 13. High Efficiency Wide Input Range Dual 12V/3.3V Converter 3859fa 36 LTC3859 TYPICAL APPLICATIONS VOUT1 RA1 115k RB1 28.7k 56pF VFB1 CITH1A 200pF LTC3859 SENSE1- C1 1nF SENSE1+ RITH1 3.93k CITH1 1000pF 100k ITH1 CSS1 0.01F FREQ PLLIN/MODE SW1 RUN1 RB2 57.6k 56pF RUN3 VFB2 CITH2 1000pF VBIAS CBIAS 10F PGND EXTVCC CINT1 4.7F CITH2A 200pF C2 10F INTVCC D2 TG2 CSS2 0.01F TRACK/SS2 MTOP2 CB2 0.1F BOOST2 L2 0.47H RSENSE2 3.5m VOUT2 1.2V 8A SW2 VOUT3 RA3 12.1k D1 RITH2 3.93k ITH2 VOUT1 1V 8A COUT1 220F s2 MBOT1 BG1 RUN2 VOUT2 RSENSE1 3.5m CB1 0.1F BOOST1 SGND L1 0.47H MTOP1 TG1 TRACK/SS1 RA2 115k C1 10F PGOOD1 RB3 232k OPT COUT2 220F s2 MBOT2 BG2 VFB3 CITH3 15nF RITH3 8.66k SENSE2+ C2 1nF ITH3 CITH3A 220pF SENSE2- CSS3 0.01F D3 MTOP1, MTOP2: RENESAS RJK0305 MBOT1, MBOT2: RENESAS RJK0328 MTOP3, MBOT3: RENESAS HAT2169H L1, L2: SUMIDA CDEP105-0R4 L3: PULSE PA1494.362NL COUT1, COUT2: SANYO 2R5TPE220M CIN, COUT3: SANYO 50CE220AX D1, D2: CMDH-4E D3: BAS140W SS3 TG3 OV3 SW3 BOOST3 MTOP3 RSENSE2 4m CB3 0.1F BG3 SENSE3 L3 3.3H MBOT3 COUT3 220F VOUT3 24V 5A VIN 12V CIN 220F - C3 1nF SENSE3+ 3859 F14 Figure 14. High Efficiency Triple 24V/1V/1.2V Converter from 12V VIN 3859fa 37 LTC3859 TYPICAL APPLICATIONS VOUT1 RB1 57.6k RA1 115k VFB1 CITH1A 100pF LTC3859 SENSE1- C1 1nF SENSE1+ RITH1 5.6k CITH1 2.2nF 100k ITH1 CSS1 0.1F C1 10F PGOOD1 MTOP1 TG1 TRACK/SS1 FREQ PLLIN/MODE SW1 RUN1 RB2 357k RA2 115k RUN3 VFB2 CITH2 3.3nF D1 VBIAS CBIAS 10F PGND EXTVCC CINT1 4.7F RITH2 9.1k ITH2 CITH2A 100pF VOUT1 1.2V 3A COUT1 220F MBOT1 BG1 RUN2 VOUT2 RSENSE1 9m CB1 0.1F BOOST1 SGND L1 2.2H C2 10F INTVCC D2 TG2 CSS2 0.1F TRACK/SS2 MTOP2 CB2 0.1F BOOST2 L2 6.5H RSENSE2 9m VOUT2 3.3V 3A SW2 VOUT3 RB3 887k RA3 115k COUT2 220F MBOT2 BG2 VFB3 CITH3 100nF RITH3 13k SENSE2+ C2 1nF ITH3 CITH3A 10pF SENSE2- CSS3 0.1F TG3 OV3 SW3 COUT3 270F * SS3 D3 RSENSE2 9m * MTOP1, MTOP2: BSZ097NO4LS MBOT1, MBOT2: BSZ097NO4LS MBOT3: BSZ097NO4L L1: WURTH 744311220 L2: WURTH 744314650 L3: COOPER BUSSMANN DRQ125-100 COUT1: SANYO 2R5TPE220MAFB COUT2: SANYO 4TPE220MAZB COUT3: SANYO SVPC270M CIN: SANYO 50CE220LX D1, D2: CMDH-4E D3: DIODES INC B360A-13-F C3 10F 50V BOOST3 BG3 MBOT3 L3 10H VOUT3 10.5V 1.2A VIN 5.8V TO 34V CIN 220F SENSE3- C3 1nF SENSE3+ 3859 F15 Figure 15. High Efficiency 1.2V/3.3V Step-Down Converter with 10.5V SEPIC Converter 3859fa 38 LTC3859 PACKAGE DESCRIPTION FE Package 38-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1772 Rev A) Exposed Pad Variation AA 4.75 REF 38 9.60 - 9.80* (.378 - .386) 4.75 REF (.187) 20 6.60 0.10 2.74 REF 4.50 REF SEE NOTE 4 6.40 2.74 REF (.252) (.108) BSC 0.315 0.05 1.05 0.10 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 0.25 REF 19 1.20 (.047) MAX 0o - 8o 0.50 (.0196) BSC 0.17 - 0.27 (.0067 - .0106) TYP 0.05 - 0.15 (.002 - .006) FE38 (AA) TSSOP 0608 REV A 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3859fa 39 LTC3859 PACKAGE DESCRIPTION UHF Package 38-Lead Plastic QFN (5mm 7mm) (Reference LTC DWG # 05-08-1701 Rev C) 0.70 p 0.05 5.50 p 0.05 5.15 0.05 4.10 p 0.05 3.00 REF 3.15 0.05 PACKAGE OUTLINE 0.25 p 0.05 0.50 BSC 5.5 REF 6.10 p 0.05 7.50 p 0.05 RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 p 0.10 0.75 p 0.05 PIN 1 NOTCH R = 0.30 TYP OR 0.35 s 45o CHAMFER 3.00 REF 37 0.00 - 0.05 38 0.40 p0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 5.15 0.10 7.00 p 0.10 5.50 REF 3.15 0.10 (UH) QFN REF C 1107 0.200 REF 0.25 p 0.05 0.50 BSC R = 0.125 TYP R = 0.10 TYP BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE M0-220 VARIATION WHKD 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3859fa 40 LTC3859 REVISION HISTORY REV DATE DESCRIPTION A 10/10 Updated Note Numbers PAGE NUMBER Updated Notes 2 and 3 text Changed 1.2V to 1.19V in RUN pin text Updated Typical Applications 2, 3, 4, 5 6 11, 15 35, 36, 37, 38, 42 3859fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 41 LTC3859 TYPICAL APPLICATION High Efficiency Wide Input Range Dual 3.3V/8.5V Converter VOUT1 RA1 68.1k RB1 215k 15pF LTC3859 SENSE1- VFB1 C1 1nF CITH1A 150pF SENSE1+ RITH1 15k CITH1 820pF 100k CSS1 0.1F ITH1 FREQ PLLIN/MODE SW1 RUN1 RB2 649k CITH2 2.2nF RUN3 COUT1 150F D1 CBIAS 10F PGND VFB2 EXTVCC ITH2 INTVCC CINT1 4.7F C2 10F D2 TG2 CSS2 0.1F TRACK/SS2 CB2 0.1F BOOST2 MTOP2 L2 6.5H RSENSE2 8m SW2 VOUT3 RA3 68.1k VOUT1 3.3V 5A VBIAS RITH2 15k CITH2A 68pF RSENSE1 6m MBOT1 BG1 RUN2 10pF L1 3.2H CB1 0.1F BOOST1 SGND RA2 68.1k MTOP1 TG1 TRACK/SS1 VOUT2 C1 10F PGOOD1 RB3 499k OPT COUT2 68F MBOT2 BG2 VOUT2 8.5V 3A VFB3 CITH3 0.01F RITH3 3.6k CITH3A 820pF CSS3 0.1F MTOP1, MTOP2: VISHAY Si7848DP MBOT1, MBOT2: BSZ097NO4LS MTOP3: BSC027NO4LS MBOT3: BSCO1BN04LS L1: SUMIDA CDEP105-3R2M L2: WURTH 744314650 L3: WURTH 744325120 COUT1: SANYO 6TPB220ML COUT2: SANYO 4TPE150M CIN, COUT3: SANYO 50CE220LX D1, D2: CMDH-4E D3: BAS140W SENSE2+ C2 1nF ITH3 SENSE2- VOUT3 10V* D3 SS3 TG3 OV3 BOOST3 SW3 MTOP3 L3 1.2H CB3 0.1F BG3 MBOT3 RSENSE2 2m COUT3 220F VIN 2.5V TO 38V (START-UP ABOVE 5V) CIN 220F SENSE3- C3 1nF SENSE3+ * VOUT3 IS 10V WHEN VIN < 10V, FOLLOWS VIN WHEN VIN > 10V 3859 TA02 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3857/LTC3857-1 LTC3858/LTC3858-1 Low IQ, Dual Output 2-Phase Synchronous Step-Down DC/DC Controllers with 99% Duty Cycle Phase-Lockable Fixed Frequency 50kHz to 900kHz, 4V VIN 38V, 0.8V VOUT 24V, IQ = 50A/170A, LTC3890/LTC3890-1 60V, Low IQ, Dual 2-Phase Synchronous Step-Down DC/DC Controller Phase-Lockable Fixed Frequency 50kHz to 900kHz, 4V VIN 60V, 0.8V VOUT 24V, IQ = 50A LTC3780 4-Switch High Efficiency Buck-Boost Controller 4V VIN 36V, 0.8V VOUT 30V, SSOP-24, 5mm 5mm QFN-32 LTC3834/LTC3834-1 LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down DC/DC Controller with 99% Duty Cycle Phase-Lockable Fixed Frequency 140kHz to 650kHz, 4V VIN 36V, 0.8V VOUT 10V, IQ = 30A/80A LT3845 Low IQ, High Voltage Synchronous Step-Down DC/DC Controller Adjustable Fixed Frequency 100kHz to 500kHz, 4V VIN 60V, 1.23V VOUT 36V, IQ = 120A, TSSOP-16 LTC3824 Low IQ, High Voltage DC/DC Controller, 100% Duty Cycle Selectable Fixed 200kHz to 600kHz Operating Frequency, 4V VIN 60V, 0.8V VOUT VIN , IQ = 40A, MSOP-10E 3859fa 42 Linear Technology Corporation LT 1010 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com " LINEAR TECHNOLOGY CORPORATION 2010