NB3N502 14 MHz to 190 MHz PLL Clock Multiplier Description The NB3N502 is a clock multiplier device that generates a low jitter, TTL/CMOS level output clock which is a precise multiple of the external input reference clock signal source. The device is a cost efficient replacement for the crystal oscillators commonly used in electronic systems. It accepts a standard fundamental mode crystal or an external reference clock signal. Phase-Locked-Loop (PLL) design techniques are used to produce an output clock up to 190 MHz with a 50% duty cycle. The NB3N502 can be programmed via two select inputs (S0, S1) to provide an output clock (CLKOUT) at one of six different multiples of the input frequency source, and at the same time output the input aligned reference clock signal (REF). http://onsemi.com MARKING DIAGRAM 8 8 1 SOIC-8 D SUFFIX CASE 751 3N502 A L Y W G Features * * * * * * * * * * * Clock Output Frequency up to 190 MHz Operating Range: VDD = 3 V to 5.5 V Low Jitter Output of 15 ps One Sigma (rms) Zero ppm Clock Multiplication Error 45% - 55% Duty Cycle 25 mA TTL-level Drive Outputs Crystal Reference Input Range of 5 - 27 MHz Input Clock Frequency Range of 2 - 50 MHz Available in 8-pin SOIC Package or in Die Form Full Industrial Temperature Range -40C to 85C These are Pb-Free Devices 1 3N502 ALYW G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package ORDERING INFORMATION Package Shipping NB3N502DG SOIC-8 (Pb-Free) 98 Units / Rail NB3N502DR2G SOIC-8 (Pb-Free) 2500 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. VDD Reference Clock X1/CLK X2 Crystal Oscillator /P Charge Pump Phase Detector Multiplier Select /M VCO TTL/ CMOS Output REF TTL/ CMOS Output CLKOUT Feedback S1 S0 GND (c) Semiconductor Components Industries, LLC, 2012 May, 2012 - Rev. 1 Figure 1. NB3N502 Logic Diagram 1 Publication Order Number: NB3N502/D NB3N502 X1/CLK 1 8 X2 VDD 2 7 S1 GND 3 6 S0 REF 4 5 CLKOUT Figure 2. Pin Configuration (Top View) Table 1. CLOCK MULTIPLIER SELECT TABLE S1* S0** Multiplier L L 2X L H 5X M L 3X M H 3.33X H L 4X H H 2.5X L = GND H = VDD M = OPEN (unconnected) * Pin S1 defaults to M when left open ** Pin S0 defaults to H when left open Table 2. OUTPUT FREQUENCY EXAMPLES Output Frequency (MHz) 20 25 33.3 48 50 54 64 66.66 75 100 108 120 135 Input Frequency (MHz) 10 10 10 16 20 13.5 16 20 15 20 27 24 27 S1, S0 0 ,0 1, 1 M, 1 M, 0 1, 1 1, 0 1, 0 M, 1 0, 1 0, 1 1, 0 0, 1 0, 1 Table 3. PIN DESCRIPTION Pin # Name I/O Description 1 X1/CLK Input 2 VDD Power Supply Positive Supply Voltage (3 V to 5.5 V) 3 GND Power Supply 0 V Ground. 4 REF CMOS/TTL Output Buffered Crystal Oscillator Clock Output 5 CLKOUT CMOS/TTL Output Clock Output 6 S0 CMOS/TTL Input Multiplier Select Pin - Connect to VDD or GND. Internal Pull-up Resistor. 7 S1 Three-level Input Multiplier Select Pin - Connect to VDD, GND or Float to M. 8 X2 Crystal Input Crystal or External Reference Clock Input Crystal Input - Do Not Connect when Providing an External Clock Reference Table 4. ATTRIBUTES Characteristic ESD Protection Value Human Body Model Machine Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 8 kV > 600 V Level 1 UL 94 V-0 @ 0.125 in 6700 Devices Meets or Exceeds JEDEC Standard EIA/JESD78 IC Latchup Test 1. For additional Moisture Sensitivity information, refer to Application Note AND8003/D. http://onsemi.com 2 NB3N502 Table 5. MAXIMUM RATINGS Symbol VDD Parameter Condition 1 Positive Power Supply Condition 2 Rating Units 7 V GND - 0.5 = VI = VDD + 0.5 V GND = 0 V VI Input Voltage TA Operating Temperature Range -40 to +85 C Tstg Storage Temperature Range -65 to +150 C qJA Thermal Resistance (Junction-to-Ambient) qJC Thermal Resistance (Junction-to-Case) 0 LFPM 500 LFPM SOIC-8 SOIC-8 190 130 C/W C/W (Note 1) SOIC-8 41 to 44 C/W Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. JEDEC standard multilayer board - 2S2P (2 signal, 2 power). Table 6. DC CHARACTERISTICS (VDD = 3 V to 5.5 V unless otherwise noted, GND = 0 V, TA = -40C to +85C) (Note 2) Symbol Characteristic Min IDD Power Supply Current (unloaded CLKOUT operating at 100 MHz with 20 MHz crystal) VOH Output HIGH Voltage IOH = -25 mA TTL High VOL Output LOW Voltage IOL = 25 mA VIH Input HIGH Voltage, CLK only (pin 1) VIL Input LOW Voltage, CLK only (pin 1) VIH Input HIGH Voltage, S0, S1 VIL Input LOW Voltage, S0, S1 VIM Input level of S1 when open (Input Mid Point) Cin Input Capacitance, S0, S1 ISC Output Short Circuit Current Typ Max 20 mA 2.4 V 0.4 (VDD / 2) + 1 Unit VDD / 2 VDD / 2 V V (VDD / 2) -1 VDD - 0.5 V V 0.5 V VDD / 2 V 4 pF 70 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Parameters are guaranteed by characterization and design, not tested in production. Table 7. AC CHARACTERISTICS (VDD = 3 V to 5.5 V unless otherwise noted, GND = 0 V, TA = -40C to +85C) (Note 3) Symbol Characteristic Min Typ Max Unit fXtal Crystal Input Frequency 5 27 MHz fCLK Clock Input Frequency 2 50 MHz fOUT Output Frequency Range VDD = 4.5 to 5.5 V (5.0 V 10%) VDD = 3.0 to 3.6 V (3.3 V 10%) 14 14 190 120 MHz MHz Clock Output Duty Cycle at 1.5 V up to 190 MHz 45 55 % DC tjitter (rms) tjitter (pk-to-pk) tr/tf 50 Period Jitter (RMS, 1 ) 15 ps Total Period Jitter, (peak-to-peak) 40 ps Output rise/fall time (0.8 V to 2.0 V / 2.0 V to 0.8 V) 1 2 ns NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. Parameters are guaranteed by characterization and design, not tested in production. http://onsemi.com 3 NB3N502 APPLICATIONS INFORMATION High Frequency CMOS/TTL Oscillators Series Termination Resistor Recommendation The NB3N502, along with a low frequency fundamental mode crystal, can build a high frequency CMOS/TTL output oscillator. For example, a 20 MHz crystal connected to the NB3N502 with the 5X output selected (S1 = L, S0 = H) produces a 100 MHz CMOS/TTL output clock. A 33 W series terminating resistor can be used on the CLKOUT pin. Crystal Load Capacitors Selection Guide The total on-chip capacitance is approximately 12 pF per pin (CIN1 and CIN2). A parallel resonant, fundamental mode crystal should be used. The device crystal connections should include pads for small capacitors from X1/CLK to ground and from X2 to ground. These capacitors, CL1 and CL2, are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance (CLOAD (crystal)). Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) between the crystal and device. Crystal load capacitors, if needed, must be connected from each of the pins X1 and X2 to ground. The load capacitance of the crystal (CLOAD (crystal)) must be matched by total load capacitance of the oscillator circuitry network, CINX, CSX and CLX, as seen by the crystal (see Figure 3 and equations below). External Components Decoupling Instructions In order to isolate the NB3N502 from system power supply, noise de-coupling is required. The 0.01 mF decoupling capacitor has to be connected between VDD and GND on pins 2 and 3. It is recommended to place de-coupling capacitors as close as possible to the NB3N502 device to minimize lead inductance. Control input pins can be connected to device pins VDD or GND, or to the VDD and GND planes on the board. Internal to Device CLOAD1 = CIN1 + CS1 + CL1 [Total capacitance on X1/CLK] CLOAD2 = CIN2 + CS2 + CL2 [Total capacitance on X2] CIN1 [ CIN2 [ 12 pF (Typ) [Internal capacitance] CS1 [ CS2 [ 5 pF (Typ) [External PCB stray capacitance] CLOAD1,2 = 2 S CLOAD (Crystal) CL2 = CLOAD2 - CIN2 - CS2 [External load capacitance on X2] CL1 = CLOAD1 - CIN1 - CS1 [External load capacitance on X1/CLK] R G CIN1 12 pF CIN2 12 pF X2 X1/CLK CS1 CS2 CL1 CL2 Example 1: Equal stray capacitance on PCB CLOAD (Crystal) = 18 pF (Specified by the crystal manufacturer) CLOAD1 = CLOAD2 = 36 pF CIN1 = CIN2 = 12 pF CS1 = CS2 = 6 pF CL1 = 36 - 12 - 6 = 18 pF CL2 = 36 - 12 - 6 = 18 pF Example 2: Different stray capacitance on PCB trace X1/CLK vs. X2 CLOAD (Crystal) = 18 pF CLOAD1 = CLOAD2 = 36 pF CIN1 = CIN2 = 12 pF CS1 = 4 pF & CS2 = 8 pF CL1 = 36 - 12 - 4 = 20 pF CL2 = 36 - 12 - 8 = 16 pF Crystal Figure 3. Using a Crystal as Reference Clock http://onsemi.com 4 NB3N502 PACKAGE DIMENSIONS SOIC-8 NB CASE 751-07 ISSUE AK -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 0.25 (0.010) M Y M 1 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X S M J SOLDERING FOOTPRINT* MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NB3N502/D