FP-301 Tubing Flexible Polyolefin Data Sheet Product Description Standard Colors Typical Applications 3MTM FP-301 Tubing offers an outstanding balance of electrical, physical and chemical properties for a wide variety of industrial and military applications. Rated for 135C continuous operation, all FP-301 Tubing is split resistant, mechanically tough, easily marked and resists cold flow. FP-301 Tubing is typically used as a shrink-fit electrical insulation over cable splices and terminations. It is also used for lightweight wire harness covering, wire marking, wire bundling, component packaging and fire-resistant covering. Shrink Ratio FP-301 Tubing meets MIL-DTL-23053/5 Class 1 & 2 and AMS-3636, AMS-3637 requirements. It is ULRecognized and CSACertified at 600 volts @ 125C (UL File Nos. E-39100 and E-69751; CSANo. 38227). FP-301 polyolefin tubing has a 2:1 shrink ratio. When freely recovered, the tubing will shrink to 50% of its as-supplied internal diameter. The recovered wall thickness of the tubing is proportional to the degree of recovery. FP-301 Tubing is rated for continuous operation from -55C (-67F) to 135C (275F) and withstands elevated temperatures to 300C (572F) for short periods. Minimum shrink temperature for all FP-301 Tubing is 100C (212F). High expansion-ratio FP-301 Tubing meeting MIL-DTL-23053/5 Class 1 requirements for overexpansion is available subject to factory quotation. FP-301, Class 1 (flame retardant)-black, white, red, blue, green (1/16 "-1" green only) and yellow. FP-301, Class 2 (nonflame retardant)-clear. Other colors available subject to factory quotation. Standard Packaging Four-foot lengths, large spools (21" diameter) and small spools (8-1/2" diameter). Ordering Information Order FP-301 by product name, size equivalent to expanded inside diameter, package type and color. Always order the largest size that will shrink snugly over the item to be covered. Example: FP-301, 1/4", 4 ft., white. Typical Properties Applicable Specification MIL-DTL-23053/5, Class 1, 2; AMS-3636, AMS-3637; UL File E-39100, E-69751; CSALR38227; ABS Standard Sizes and Dimensions Ordering Size 3/64 1/16 3/32 1/8 3/16 1/4 3/8 1/2 3/4 1 1-1/2 2 3 4 Expanded ID Minimum Recoverd ID Maximum in. (mm) in. .046 .063 .093 .125 .187 .250 .375 .500 .750 1.000 1.500 2.000 3.000 4.000 (1,17) (1,60) (2,36) (3,18) (4,75) (6,35) (9,53) (12,70) (19,05) (25,40) (38,10) (50,80) (76,20) (101,60) .023 .031 .046 .062 .093 .125 .187 .250 .375 .500 .750 1.000 1.500 2.000 (mm) Recoverd Wall Thickness (Nominal) in. (mm) (0,58) (0,79) (1,17) (1,57) (2,36) (3,18) (4,75) (6,35) (9,53) (12,70) (19,05) (25,40) (38,10) (50,80) .016 .017 .020 .020 .020 .025 .025 .025 .030 .035 .040 .045 .050 .055 (0,41) (0,43) (0,51) (0,51) (0,51) (0,64) (0,64) (0,64) (0,76) (0,89) (1,02) (1,14) (1,27) (1,40) Physical Electrical Tensile Strength 2400 PSI Ultimate Elongation 400% Longitudinal Change 5% Secant Modulus (2%) 13,000 PSI Specific Gravity 1.3(Black) .93 (Clear) Heat Aging Elongation (336 hrs. @ 175C) 175% Heat Shock No dripping, (4 hrs. @ 250C) cracking, passes mandrel wrap test Low Temperature Flexibility (4 hrs. @ -55C) No cracking Flammability Self-extinguish meets UL 224 All-Tubing Flame Test (Class 1 only) Dielectric Strength 900 V/mil Volume Resistivity 1015 ohm-cm Chemical Corrosive Effect Non-corrosive Solvent Resistance Tensile Strength 1000 PSI Dielectric Strength 400 V/mil Water Absorption 0.2% Fungus Resistance Non-nutrient Technical information provided consists of typical product data and should not be used for specification purposes. Unless otherwise noted, all tests are performed at room temperature.