CP2-HAB110-E1-TG30 - 3M - Datasheet.Live

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

25 mm basic system unit

38, 44 and 50 mm module

2 mm grid spacing allows for high signal density at low cost

“Eye of the Needle” compliant pin press-ﬁt design reduces manufacturing

time and cost

Three contact mating levels for Early Mate Late Break or “Hot Swap”

applications reduces manufacturing time and cost

Feed through termination available for midplane applications

Additional grounding rows available for improved ground bounce and

EMI immunity

Mates with 5-row 3M™ MetPak™ HSHM, HM and CP2 Sockets

End-to-end stackable with 5-row 3M™ MetPaK™ HSHM, HM and CP2

Headers

See Regulatory Information Appendix (RIA) for chemical compliance

information

Date Modiﬁed: February 8, 2008 TS-2263-A

Sheet 1 of 7

•

Physical

Insulation:

Material: Glass Filled Polyester (PBT)

Flammability: UL94V-0

Contact:

Material: Copper Alloy

Plating: See Ordering Information

Mechanical

Mating Force: ≤ 0.75N/PIN

Withdrawl Force: ≥ 0.15N/PIN

Mating and Un-mating Operations: 50

Electrical

Contact Resistance: ≤ 20 mΩ

Insulation Resistance: ≥ 10,000 MΩ

Test Voltage: 750 VACRMS

Environmental

Temperature Ratings: -40°C to +85°C

PCB Data

Recommended PCB Plated Through Hole: Φ 0.6±0.05 mm

Drill hole diameter: Φ 0.7±0.02 mm

Hole platings: Cu 25~50μm, Sn or SnPb<10 μm

PCB thickness: 2.4-5.6 mm

Press-In Force: ≤ 204N/pin on nominal hole diameter

Retention Force: ≥ 13.5N/pin on nominal hole diameter

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 2 of 7

Ordering Information

CP2-HABXXX-XXX-XXXX

RECOMMENDED PCB LAYOUT

Signal

Contact

Quantity

Dimension A Dimension B Dimension C

95 38.00 [1.496] 38.30 [1.508] 36.00 [1.417]

110 44.00 [1.732] 44.30 [1.744] 42.00 [1.653]

125 50.00 [1.968] 50.30 [1.980] 48.00 [1.890]

"A"

"C"

Tail

Mating

length

Mating

length

Tail

"B"

Number of Signal Contacts

095,110 and125

Loading Conﬁgurations

(See diagrams on following pages)

Grounding Options:

G= with ground pins

Blank= without ground pins

EMLB Patterns

Primary Tail Length

1= 3.7 mm

4= 16.0 mm

Plating Options

TG30= 30∼40 μ” Gold Contact Area

100∼200 μ“ Bright Tin-Lead

50∼80 μ” Nickel Underplate

(RIA E2 & C2 apply)

FJ= 10∼20 μ” Gold Contact Area

200∼300 μ“ Matte Tin

50∼80 μ” Nickel Underplate

(RIA E1 & C1 apply)

KR= 30∼40 μ” Gold Contact Area

200∼300 μ” Matte Tin

50∼80 μ” Nickel Underplate

(RIA E1 & C1 apply)

GG30 = 30~40 u” Two Gold Contact Areas

100~200 u” Bright Tin-Lead

50~80 u” Nickel Underplate

(RIA C2 & E2 apply)

• This diagram serves only for Part Number descriptive deﬁnitions.

• For standard product conﬁguration please see following pages.

PLEASE CONTACT YOUR LOCAL SALES REPRESENTATIVE FOR CUSTOMER SPECIFIC PRODUCT CONFIGURATIONS.

[Inch]

0.13

1 0.3

Tolerance Unless Noted

0. .0 .00

[ ] Dimensions for

Reference only

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 3 of 7

CP2-HAB095-E1-TG30 Connector Type B19

EAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

CP2-HAB095-GE1-TG30 Connector Type B19

FCCCCCCCC CCCCCCCC

EAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAA

ZCCCCCCCC CCCCCCCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

CP2-HAB095-A1-TG30 Connector Type B19

EBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

CP2-HAB095-GA1-TG30 Connector Type B19

FCCCCCCCC CCCCCCCC

EBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBB

ZCCCCCCCC CCCCCCCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 4 of 7

CP2-HAB095-GA4-GG30 Connector Type B19

FTTTTTTTT TTTTTTTT

ERRRRRRRRRRRRRRRRRRR

DRRRRRRRRRRRRRRRRRRR

CRRRRRRRRRRRRRRRRRRR

BRRRRRRRRRRRRRRRRRRR

ARRRRRRRRRRRRRRRRRRR

ZTTTTTTTT TTTTTTTT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Signal Contact Conﬁguration Worksheet Connector Type B19

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

CP2-HAB110-E1-TG30 Connector Type B22

EAAAAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

CP2-HAB110-GE1-TG30 Connector Type B22

FCCCCCCCCC CCCCCCCCC

EAAAAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAA

ZCCCCCCCCC CCCCCCCCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 5 of 7

CP2-HAB110-A1-TG30 Connector Type B22

EBBBBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBBBBB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

CP2-HAB110-GA1-TG30 Connector Type B22

FCCCCCCCCC CCCCCCCCC

EBBBBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBBBBB

ZCCCCCCCCC CCCCCCCCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

CP2-HAB110-GA4-GG30 Connector Type B22

FT T T T T T T T T T T T T T T T T T

ERRRRRRRRRRRRRRRRRRRRRR

DRRRRRRRRRRRRRRRRRRRRRR

CRRRRRRRRRRRRRRRRRRRRRR

BRRRRRRRRRRRRRRRRRRRRRR

ARRRRRRRRRRRRRRRRRRRRRR

ZT T T T T T T T T T T T T T T T T T

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Signal Contact Conﬁguration Worksheet Connector Type B22

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 6 of 7

CP2-HAB125-E1-TG30 Connector Type B25

EAAAAAAAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAAAAA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

CP2-HAB125-GE1-TG30 Connector Type B25

FBBBBBBBBBBB BBBBBBBBBBB

EAAAAAAAAAAAAAAAAAAAAAAAAA

DAAAAAAAAAAAAAAAAAAAAAAAAA

CAAAAAAAAAAAAAAAAAAAAAAAAA

BAAAAAAAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAAAAA

ZBBBBBBBBBBB BBBBBBBBBBB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

CP2-HAB125-A1-TG30 Connector Type B25

EBBBBBBBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBBBBBBBB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

CP2-HAB125-GA1-TG30 Connector Type B25

FCCCCCCCCCCC CCCCCCCCCCC

EBBBBBBBBBBBBBBBBBBBBBBBBB

DBBBBBBBBBBBBBBBBBBBBBBBBB

CBBBBBBBBBBBBBBBBBBBBBBBBB

BBBBBBBBBBBBBBBBBBBBBBBBBB

ABBBBBBBBBBBBBBBBBBBBBBBBB

ZCCCCCCCCCCC CCCCCCCCCCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Electronic Solutions Division

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ CP2 Press-Fit Header

2 mm Type AB, 95, 110 and 125 Signal Contacts CP2 Series

TS-2263-A

Sheet 7 of 7

CP2-HAB125-GA4-GG30 Connector Type B25

FTTTTTTTTTTT TTTTTTTTTTT

ERRRRRRRRRRRRRRRRRRRRRRRRR

DRRRRRRRRRRRRRRRRRRRRRRRRR

CRRRRRRRRRRRRRRRRRRRRRRRRR

BRRRRRRRRRRRRRRRRRRRRRRRRR

ARRRRRRRRRRRRRRRRRRRRRRRRR

ZTTTTTTTTTTT TTTTTTTTTTT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Signal Contact Conﬁguration Worksheet Connector Type B25

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Regulatory Information Appendix

3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product is RoHS Compliant 2005/95/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/747/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as

amended by Commission Decision 2005/618/EC.

This product contains lead in the solder tail area in excess of the maximum concentration value allowed.

Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information

provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/717/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217B-D

Appendix E5: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under

Item 6 of the Annex to the Directive.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of

the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless

the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information

represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

CHINA

Appendix C1: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for

Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means

that the product or part does not contain any of the following substances in excess of the following maximum concentration

values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls

or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and

Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for

Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that

the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration

values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls

or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an

extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with

3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the

product Warranty stated below.

RIA-2217B-D

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness

is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated

with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order

shall have no force or effect unless expressly agreed upon, in writing, by an authorized ofﬁcer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES

INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the

warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except

where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of

the legal theory asserted.

Please recycle. Printed in USA.

RIA-2217B-D

3M Electronics Solutions Division

6801 River Place Blvd.

Austin, TX 78726-9000

U.S.A.

1-800-225-5373

www.3m.com/interconnects 3M is a trademark of 3M Company.

Appendix C3: China RoHS