SPPH1 1.5mm-travel Vertical Type Vertical push switch with two types of knob available Detector Typical Specifications Items Specifications Slide Ratingmax. / min. Resistive load 0.1A 30V DC / 50A 3V DC Contact resistance Initial/After operating life 20m max. / 40m max. Operating force Refer to the products line Push Without load 10,000 cycles Operating life With load 10,000 cycles0.1A 30V DC Rotary Product Line Changeover timing Travel Total travel Mounting mm mm method Poles knob style Operating force Operation Terminal type Minimum order unitpcs. Japan Export Power Latching SPPH110800 Momentary SPPH110300 Standard Dual-in-line Package Type Straight Latching SPPH120400 Momentary SPPH120100 Latching SPPH130400 Short 1 2 - 0.7 N Non shorting 1.5 PC board 2.5 Standard 800 Momentary 2 Snap-in Horizontal Type Momentary SPPH140100 Vertical Type Latching Short Snap-in Drawing No. 1 2 1 SPPH130100 SPPH140300 Straight 1 3 N - 0.7 4,000 Latching Short Standard Product No. SPPH110900 2 1 SPPH130500 SPPH140400 2 Packing Specifications Bulk Number of packagespcs. 1 case / Japan 1 case / export packing Export package measurements mm 800 4,000 400x270x290 Refer to P.130 for soldering conditions. 122 SPPH11.5mm-travel Vertical Type Unit:mm No. PC board mounting hole dimensions Viewed from the direction A Style A 10 4 10 7 Travel Total travel (5) 5 o0.9 hole 2.5 o0.9 hole 8.5 2.5 2.5 2.5 Thickness of PC board t=1.6mm 0.6 3.5 0.35 Terminal No.4 2.5 5 2.5 Power Straight terminal Snap-in terminal Total travel (5) 4.1 0.4 2.5 2 1.5 (0.2) 2.2 13.5 2.5 o0.9 hole 0.6 2.5 Thickness of PC board t=1.6mm 2.5 Terminal Configuration Straight terminal Unit:mm Vertical Type Snap-in terminal R1 1.9 (3.5) 0.8 1 2 3 3.9 0.35 5 5 2.8 Circuit DiagramViewed from Direction A 4 5 6 2.5 (3.5) 2.5 5 2.5 Horizontal Type 0.35 o0.9 hole Terminal No.4 3.5 8.5 5 2 Travel 10 7 4 5 10 Dual-in-line Package Type A (1.5) Rotary 17.5 9 1.5 .5 4.1 2.5 R0 5 11 2 1 2- (0.2) (1.8) .5 3.3 Push 2.5 2.5 3.3 R0 Snap-in terminal Slide Straight terminal 2- Detector Dimensions 0.35 123 SPEH SPEJ SPPH4 SPPH1 W 6 7 6.5 10 D 6 7 8.5 10 H 5 5.95 Travelmm -- -- 2.2 1.5 Total travelmm 1.6 1.7 3 2.5 Number of poles 1 Operating temperature range -40 to 90 -40 to 85 Automotive use Ratingmax. Resistive load 50mA 16V DC 0.2A 14V DC 0.1A 30V DC Ratingmin. Resistive load 10A 1V DC -- 50A 3V DC Operating life without load 100,000cycles 400m max. 10,000cycles 150m max. 10,000cycles 100m max. 10,000cycles 40m max. Operating life with load at max. rated load 100,000cycles 400m max. 10,000cycles 150m max. 10,000cycles 100m max. 10,000cycles 40m max. Initial contact resistance 200m max. 150m max. 100m max. 20m max. Insulation resistance 100M min. 100V DC 100M min. 500V DC Voltage proof 250V AC for 1minute 500V AC for 1minute Terminal strength -- -- 50N 49N 30N 50N -- -- 10N -- Cold -40 1000h -40 500h -20 96h Dry heat 90 1000h 85 500h 85 96h Damp heat 60, 90 to 95%RH 1000h 60, 90 to 95%RH 500h 40, 90 to 95%RH 96h 119 120 Detector Vertical Series Photo Push 8.5 -10 to 60 -- Vertical Type Page Horizontal Type Environmental performance Dual-in-line Package Type Mechanical Operating performance Actuator direction strength Pulling direction Power Electrical performance Rotary 2 Life cycle Durability Slide Dimensions mm 5N for 1minute 121 122 Push Switches Soldering Conditions 130 Push Switches Cautions 131 Note Indicates applicability to all products in the series. 109 Push Switches / Soldering Conditions Detector Example of Reflow Soldering Condition 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: T hermocouple 0.1 to 0.2 CA (K) or CC (T) at soldering portion (copper foil surface). A heat resisting tape should be used for fixed measurement. 3. Temperature profile Push Temperature (C ) Slide 300 A max. B 200 D E 100 Rotary Room temperature Time (s) Pre-heating F max. C Power Dual-in-line Package Type SeriesReflow type A 3s max. B Cs D E Fs 260 230 40 180 150 120 SPEJ SPEF SPEH Horizontal Type Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Vertical Type Reference for Hand Soldering Series Soldering temperature Soldering time SPPJ3, SPPJ2, SPUN, SPPH4, SPPH1 35010 3+1/0s SPED2, SPED4 35010 30.5s SPEJ 35010 4s max. SPEF 3505 3s max. SPEH 350 max. 3s max. SPUJ 30010 3+1/0s Reference for Dip Soldering (For PC board terminal types) Series 130 For PC board Items Dip soldering Preheating temperature Preheating time Soldering temperature Duration of immersion SPPJ3 100 max. 60s max. 2605 51s SPUN 100 max. 60s max. 2605 101s SPUJ, SPPH4 -- 2605 51s SPPJ2, SPPH1, SPED2, SPED4, SPEF -- 2605 101s