DSC8002 Series Programmable Low-Power CMOS Oscillator 1.8 to 3.3V General Description Features The DSC8002 is a programmable MEMS based PureSiliconTM Oscillator. Using the DragonFlyTM or TimeFlashTM handheld programmer, the end user can program the DSC8002 within seconds to any frequency from 1 to 150MHz in increments of 100Hz (up to four decimal point resolution). The nominal operational range spans from 1.8 to 3.3 Volts, without any need for additional external components, providing ease of use and flexibility in multi-voltage applications. The DSC8002 incorporates an all silicon resonator that is extremely robust and nearly immune to stress related fractures, common to crystal based oscillators. Without sacrificing the performance and stability required of today's systems, a crystal-less design allows for a higher level of reliability, making the DSC8002 ideal for rugged, industrial, and portable applications where stress, shock, and vibration can damage quartz crystal based systems. Available in industry standard packages, the DSC8002 can be "dropped-in" to the same PCB footprint as standard crystal oscillators. Benefits Block Diagram VDD Output Resonator Pin for pin "drop in" replacement for industry standard oscillators Semiconductor level reliability, significantly higher than quartz Frequency Resolution to 4 decimals Fully Programmable Operating Voltage and Frequency Longer Battery Life / Reduced Power Compact Plastic package Cost Effective VCO PFD Applications Frac-N PLL Standby# Frequency Range: 1 to 150MHz Exceptional Stability over Temperature o 25 PPM, 50 PPM Operating voltage o 1.8 to 3.3V (nominal) o 1.65 to 3.60V (absolute max) Operating Temperature Range o Industrial -40C to 85C o Ext. Commercial -20C to 70C o Commercial 0C to 70C Low Operating and Standby Current o 3mA Operating (40MHz) o 1uA Standby Ultra Miniature Footprint o 2.5 x 2.0 x 0.85 mm o 3.2 x 2.5 x 0.85 mm o 5.0 x 3.2 x 0.85 mm o 7.0 x 5.0 x 0.85 mm Excellent shock and Vibration Resistance Lead Free, RoHS & Reach SVHC Compliant Handheld programmer available for purchase GND Mobile Applications Consumer Electronics Portable Electronics CCD Clock for VTR Cameras Low Profile Applications Industrial (pin1) All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 1 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator Absolute Maximum Ratings1 Ordering Code Item Min. Max Unit Supply Voltage -0.3 +4.0 V Input Voltage -0.3 VDD+0.3 V Junction Temp - +150 C Storage Temp -55 +150 C - +260 C Soldering Temp ESD - Condition DSC8002 2000 200 CDM 500 - 032.0000 T Family Package, Temp & Stability 40 sec max. Tape/ Reel Output Freq 1.0 to 150MHz V HBM MM CE1 * See Ordering Information for details Recommended Operating Conditions Parameter Symbol Range Supply Voltage VDD 1.65 - 3.60V Output Load ZL R>10K, C15pF T -40 - +85 C -20 - +70 C 0 - +70 C Operating Temperature Option 1 Option 2 Option 3 Specifications Parameter Frequency Frequency Tolerance Option 1 Option 2 Option 3 Supply Current, no load Supply Current, standby Output Logic Levels Output logic high Output logic low Output Transition time Rise Time Fall Time Output Startup Time2 Output Disable Time Output Duty Cycle Input Logic Levels Input logic high Input logic low Jitter, Cycle to Cycle Symbol f0 Condition Single Frequency Min. 1 Typ. Max. 150 Unit MHz ppm f IDD IDD -40C to +85C -20C to +70C 0C to +70C CL=0p 1 to 40MHz RL= 40 to 80MHz T=25C 80 to 125MHz 125 to 150MHz T=25C VOH VOL CL=15pF tR tF tSU CL=15pF; T=25C 20%/80%*VDD T=25C 25,50 25,50 25,50 3 4 5 6 0.8*VDD - tDA mA 10 1.0 uA 0.2*VDD Volts 1.3 1.3 3 2 2 10 ns ms 20 100 ns SYM 45 55 % VIH VIL JCC 0.75*VDD - 0.25* VDD Volts F = 100MHz3 95 ps Notes: 1. Absolute maximum ratings are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated beyond these limits. 2. Output frequency to within 100ppm of final stable output frequency. 3. See typical cycle to cycle jitter graph for frequency dependence. All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 2 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator Nominal Performance Characteristics 1.8V Characteristics Supply Current Standby Current 1 Ta = 25C 1pF 8pF 15pF Standby Current (A) Supply Current (mA) 16 12 8 4 0 -40C 0.8 0.6 0.4 0.2 50 100 Frequency (MHz) 150 0 50 100 Frequency (MHz) 150 Fall Time Rise Time 2 2 -40C 25C 85C -40C 1.5 Fall Time (ns) Rise Time (ns) 85C 0 0 1 0.5 0 25C 85C 1.5 1 0.5 0 0 50 100 Frequency (MHz) 150 0 Period Jitter 50 100 Frequency (MHz) 150 Cycle to Cycle Jitter 40 200 25C 25C 30 150 Jitter (ps) RMS Jitter (ps) 25C 20 100 10 50 0 0 0 50 100 Frequency (MHz) 150 0 50 100 Frequency (MHz) 150 All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 3 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator 3.3V Characteristics Supply Current Standby Current 1 Ta = 25C 1pF 8pF 15pF Standby Current (A) Supply Current (mA) 16 12 8 4 0 -40C 0.8 0.6 0.4 0.2 50 100 Frequency (MHz) 150 0 Rise Time 50 100 Frequency (MHz) 150 Fall Time 2 2 -40C 25C 85C -40C 1.5 Fall Time (ns) Rise Time (ns) 85C 0 0 1 0.5 0 25C 85C 1.5 1 0.5 0 0 50 100 Frequency (MHz) 150 0 Period Jitter 50 100 Frequency (MHz) 150 Cycle to Cycle Jitter 40 200 25C 25C 30 150 Jitter (ps) RMS Jitter (ps) 25C 20 100 10 50 0 0 0 50 100 Frequency (MHz) 150 0 50 100 Frequency (MHz) 150 All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 4 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator Output Waveform tR tF 80% Output 50% 20% tEN 1/fo tDA VOH Standby# VOL Standby Function Standby# Output (pin 1) (pin 3) Hi Level Output ON Open (no connect) Output ON Low Level High Impedance Test Circuit IDD VDD 0.01uF 4 3 1 2 15pF *VSD *VSD = Standby# Logic Level Input All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 5 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator Board Layout (recommended) Solder Reflow Profile 20-40 Sec MSL 1 @ 260C refer to JSTD-020C Ramp-Up Rate (200C to Peak Temp) 3C/Sec Max. Preheat Time 150C to 200C 60-180 Sec Time maintained above 217C 60-150 Sec 255-260C Peak Temperature Time within 5C of actual Peak 20-40 Sec 6C/Sec Max. Ramp-Down Rate Time 25C to Peak Temperature 8 min Max. Se 3C / 217C 200C 60-150 Sec S 6C/ ec 3C / Se cM ax . Reflow 25C 60-180 Sec x. 150C Ma Temperature (C) cM ax . 260C Cool Pre heat Time 8 min max Package Dimensions 7.0 x 5.0 mm Plastic Package External Dimensions 7.00.10 [0.2760.004] #4 Recommended Land Pattern* 5.08 [0.200] 5.08 [0.2] #3 #4 #3 2.6 [0.102] 2.6 [0.102] 3.5 [0.138] 0.2 [0.008] 2.2 [0.087] #1 #2 5.00.10 [0.1970.004] #2 1.4 [0.055] 0.2 [0.008] #1 0.850.05 [0.0330.002] o o o o o 1.4 [0.055] 0.2 [0.008] 1.4 [0.055] 1.2 [0.047] No. 1 2 3 4 o Pin Terminal Standby# GND Output VDD *Note: The center pad is not connected internally and should be left unconnected or tied to GND. units: mm [inch] All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 6 | MK-Q-B-P-D-031809-06-6 DSC8002 Series 1.8 to 3.3V Programmable Low-Power CMOS Oscillator 5.0 x 3.2 mm Plastic Package External Dimensions 2.54 [0.100] 2.54 [0.100] 50.10 [0.1970.004] #4 Recommended Land Pattern #3 #4 #3 1.2 [0.047] 2.1 [0.083] 0.2 [0.008] 1.1 [0.043] 0.1 [0.004] #2 1.2 [0.047] #1 #2 3.20.10 [0.1260.004] #1 0.1 [0.004] 1.2 [0.047] 0.9 [0.035] No. 1 2 3 4 0.850.05 [0.0330.002] Pin Terminal Standby# GND Output VDD units: mm [inch] 3.2 x 2.5 mm Plastic Package External Dimensions 3.20.05 [0.1260.002] #4 Recommended Land Pattern 2.1 [0.083] 2.1 [0.083] #3 #3 #4 0.9 [0.035] 0.9 [.035] 1.0 [0.039] CO.25 #1 #2 #2 0.90.05 [0.0350.002] #1 2.50.05 [0.0980.002] 0.80.1 [0.0310.004] 0.850.05 [0.0330.002] No .1 2 3 4 Pin Terminal Standby# GND Output VDD 0.2 [0.008] 0.9 [0.035] units: mm [inch] All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 7 | MK-Q-B-P-D-031809-06-6 1.8 to 3.3V DSC8002 Series Programmable Low-Power CMOS Oscillator 2.5 x 2.0 mm Plastic Package External Dimensions 2.50.05 [0.0980.002] #4 Recommended Land Pattern 1.65 [0.065] 1.65 [0.065] #3 #3 #4 0.7 [0.028] 0.7 [0.028] 0.85 [0.033] CO.25 #1 #2 0.650.05 [0.0260.002] #2 2.00.05 [0.0790.002] #1 0.2 [0.008] 0.65 [0.026] 0.650.10 [0.0260.004] No .1 2 3 4 0.850.05 [0.0330.002] Pin Terminal Standby# GND Output VDD units: mm [inch] Ordering Information DSC8002 PTS - T Package (Plastic QFN) P=A: P=B: P=C: P=D: 7.0x5.0mm 5.0x3.2mm 3.2x2.5mm 2.5x2.0mm Temperature Stability T=C: 0o ~ +70o C T=E: -20o ~ +70o C T=I: -40o ~ +85o C S=1: 50ppm S=2: 25ppm - Packing Option Blank: Tubes T: Tape & Reel Disclaimer: Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel's terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. MICREL, Inc. Phone: +1 (408) 944-0800 2180 Fortune Drive, Fax: +1 (408) 474-1000 San Jose, California 95131 Email: hbwhelp@micrel.com USA www.micrel.com All Rights Reserved. No part of this document may be copied or reproduced in any form without the prior written permission of Micrel, Inc. Micrel Inc. may update or make changes to the contents, products, programs or services described at any time without notice. This document neither states nor implies any kind of warranty, including, but not limited to implied warranties of merchantability or fitness for a particular use. Page 8 | MK-Q-B-P-D-031809-06-6