GFE1300-547 1300 nm Edge Emitting LED FEATURES * Typically 15 W into 9/125 m fibre with 1ms pulse at 100 mA * Pulse at 100 mA * Spectral width 60 nm * Bandwidth of 200 MHz * Operating temperature-10C to +65C OPHO_229.doc DESCRIPTION The GFE1300-547 is a high performance 1300 nm Edge emitting LED specifically designed for coupling high power into Monomode optical fibers. OUTLINE DIMENSIONS in inches (mm) When pulsed at 100mA typical coupled power into 9/125 m fiber is 15 w. Bandwidth is typically 200 MHz. Where applicable, standard pin orientation aligns pin 2 with the receptacle keyway. This orientation will be supplied unless requested otherwise. The heatsink tab is removed to allow alignment in some receptacles. This device is very susceptible to damage by electrostatic discharge. All dimensions are in millimetres. Tolerances are 0.10 mm unless otherwise stated. Receptacle illustrated with typical active device installed. High precision ceramic bore. Device alignment to fibre tested with AT&T ST2 connector. ODIM_234.tif Pinout 1. Cathode 2. Anode 3. Case ST is a registered trademark of AT & T. 240 h Honeywell reserves the right to make changes in order to improve design and supply the best products possible. GFE1300-547 1300 nm Edge Emitting LED ELECTRO-OPTICAL CHARACTERISTICS PARAMETER SYMBOL MIN TYP Power (9/125 m NA0.11) Power (50/125 m NA 0.20) Power (62.5/125 m NA 0.27) Peak emission wavelength Spectral width between half power point -3dB Bandwidth Forward Voltage Connectorised power repeatability PUa 8 40 cI ec fU V 1270 15 50 70 1300 60 200 1.6 MAX 1330 100 2.0 1.5 UNITS TEST CONDITIONS W I = 100 mA 1ms pulse nm nm MHz V dB I = 100 mA I = 100 mA = 100 mA +20 mApI = 100 mA [A] Notes 1. Applies to 9/125 m fibre terminated with a recommended ceramic ferrule in group B receptacles. LIMITING VALUES PARAMETER SYMBOL Continuous forward current Repetitive peak forward current Reverse Voltage Operating temperature Storage temperature Soldering temperature I IS V Ta(R) TOa TOU MIN TYP MAX 110 150 1.0 -10 -40 +65 +65 UNITS TEST CONDITIONS mA mA V C C C 260 50% duty cycle 2 mm form the case for 10 s THERMAL CHARACTERISTICS PARAMETER SYMBOL Radiant power temperature coefficient Wavelength temperature coefficient MIN dP/dT dae/dT TYP -3.5 0.8 MAX UNITS TEST CONDITIONS %/C nm/C ABSOLUTE MAXIMUM RATINGS (25C Free-Air Temperature unless otherwise noted) Storage temperature -55 to +100C Case operating temperature -40 to +100C Lead solder temperature 260C, 10s Continuous forward current (heat sinked) 100 mA Reverse voltage 1 V @ 10 A Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Honeywell reserves the right to make changes in order to improve design and supply the best products possible. h 241 GFE1300-547 1300 nm Edge Emitting LED ORDER GUIDE Description Catalog Listing 1300 nm Surface emitting LED GFE1300-547 CAUTION The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. Fig. 1 Fig. 2 OGRA_159.TIF OGRA_160.tif Fig. 3 OGRA_161.tif 242 h Honeywell reserves the right to make changes in order to improve design and supply the best products possible.