GFE1300-547
1300 nm Edge Emitting LED
OUTLINE DIMENSIONS in inches (mm)DESCRIPTION
ST is a registered trademark of AT & T.
The GFE1300-547 is a high performance 1300 nm Edge
emitting LED specifically designed for coupling high
power into Monomode optical fibers.
When pulsed at 100mA typical coupled power into 9/125
µm fiber is 15 µw. Bandwidth is typically 200 MHz.
Where applicable, standard pin orientation aligns pin 2
with the receptacle keyway. This orientation will be
supplied unless requested otherwise.
The heatsink tab is removed to allow alignment in some
receptacles.
This device is very susceptible to damage by electrostatic
discharge.
All dimensions are in millimetres. Tolerances are ± 0.10
mm unless otherwise stated.
Receptacle illustrated with typical active device installed.
High precision ceramic bore.
Device alignment to fibre tested with AT&T ST2
connector.
FEATURES
Typically 15 µW into 9/125 µm fibre with 1ms pulse
at 100 mA
Pulse at 100 mA
Spectral width 60 nm
Bandwidth of 200 MHz
Operating temperature-10¡C to +65¡C
ODIM_234.tif
OPHO_229.doc
Pinout
1. Cathode
2. Anode
3. Case
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible.
240 h
GFE1300-547
1300 nm Edge Emitting LED
TYP
MIN UNITS
T
EST CONDITION
S
PARAMETER SYMBOL MAX
ELECTRO-OPTICAL CHARACTERISTICS
I¸ = 100 mAPower
(
9/125
µ
m NA0.11
)
P¸Û£ßå
µ
W815
1ms
p
ulsePower
(
50/125
µ
m NA 0.20
)
40 50
Power
(
62.5/125
µ
m NA 0.27
)
70
I¸ = 100 mAPeak emission wavelen
g
th çÎ nm1270 1300 1330
I¸ = 100 mAS
p
ectral width between half
p
ower
p
oint êç nm60 100
= 100 mA +20 mA
p-
-3dB Bandwidth MHz200
I¸ = 100 mAForward Volta
g
e V1.6 2.0
[À] Connectorised
p
ower re
p
eatabilit
y
dB±1.5
Notes
1. Applies to 9/125 µm fibre terminated with a recommended ceramic ferrule in group B receptacles.
TYP
MIN UNITS
T
EST CONDITION
S
PARAMETER SYMBOL MAX
LIMITING VALUES
Continuous forward current mA110
50% dut
y
c
y
cleRe
p
etitive
p
eak forward current I¸ßŠ mA150
Reverse Volta
g
e V1.0
O
p
eratin
g
tem
p
erature Tண ¡C-10 +65
Stora
g
e tem
p
erature TØä‚ ¡C-40 +65
2 mm formSolderin
g
tem
p
erature TØÚ° ¡C
the case for 10 s260
TYP
MIN UNITS
T
EST CONDITION
S
PARAMETER SYMBOL MAX
THERMAL CHARACTERISTICS
Radiant
p
ower tem
p
erature coefficient dP/dT¤ %/¡C-3.5
Wavelen
g
th tem
p
erature coefficient dæ/dT¤ nm/¡C0.8
ABSOLUTE MAXIMUM RATINGS
(25¡C Free-Air Temperature unless otherwise noted)
-55 to +100¡CStorage temperature
-40 to +100¡CCase operating temperature
260¡C, 10sLead solder temperature
100 mAContinuous forward current
(heat sinked)
1 V @ 10 µAReverse voltage
Stresses greater than those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect
reliability.
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible. h241
GFE1300-547
1300 nm Edge Emitting LED
Description Catalog Listing
ORDER GUIDE
GFE1300-5471300 nm Surface emitting LED
The inherent design of this component causes
it to be sensitive to electrostatic discharge
(ESD). To prevent ESD-induced damage
and/or degradation to equipment, take normal
ESD precautions when handling this product.
C
A
U
TI
O
N
Fig. 1 OGRA_159.TIF Fig. 2 OGRA_160.tif
Fig. 3 OGRA_161.tif
Honeywell reserves the right to make
changes in order to improve design and
supply the best products possible.
242 h