MC10EL52, MC100EL52 5VECL Differential Data and Clock D Flip-Flop Description http://onsemi.com MARKING DIAGRAMS* 8 1 SOIC-8 D SUFFIX CASE 751 1 1 1 > 100 V Machine Model * PECL Mode Operating Range: VCC = 4.2 V to 5.7 V * * * * * * * with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = -4.2 V to -5.7 V Internal Input Pulldown Resistors on D and CLK Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test Moisture Sensitivity Level 1 For Additional Information, see Application Note AND8003/D Flammability Rating: UL 94 V-0 @ 0.125 in, Oxygen: Index 28 to 34 Transistor Count = 48 devices Pb-Free Packages are Available KEL52 ALYW G 1 8 HL52 ALYWG G 4Y M G G * 365 ps Propagation Delay * 2.0 GHz Toggle Frequency * ESD Protection: > 1 kV Human Body Model, 8 HEL52 ALYW G 8 8 TSSOP-8 DT SUFFIX CASE 948R Features 8 1 4 1 KL52 ALYWG G 2N M G G The MC10EL/100EL52 is a differential data, differential clock D flip-flop with reset. The device is functionally equivalent to the E452 device with higher performance capabilities. With propagation delays and output transition times significantly faster than the E452, the EL52 is ideally suited for those applications which require the ultimate in AC performance. Data enters the master portion of the flip-flop when the clock is LOW and is transferred to the slave, and thus the outputs, upon a positive transition of the clock. The differential clock inputs of the EL52 allow the device to also be used as a negative edge triggered device. The EL52 employs input clamping circuitry so that under open input conditions (pulled down to VEE) the outputs of the device will remain stable. The 100 Series contains temperature compensation. 1 4 DFN8 MN SUFFIX CASE 506AA H = MC10 K = MC100 4Y = MC10 2N = MC100 A = Assembly Location L Y W M G = Wafer Lot = Year = Work Week = Date Code = Pb-Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. (c) Semiconductor Components Industries, LLC, 2006 December, 2006 - Rev. 5 1 Publication Order Number: MC10EL52/D MC10EL52, MC100EL52 Table 1. TRUTH TABLE D 1 D 8 D 2 7 VCC Q D* CLK* Q L H Z Z L H Z = LOW to HIGH Transition * Pin will default low when left open. CLK CLK 3 6 4 5 Table 2. PIN DESCRIPTION Q PIN VEE Figure 1. Logic Diagram and Pinout Assignment FUNCTION D, D CLK, CLK Q, Q VCC VEE ECL Data Input ECL Clock Input ECL Data Output Positive Supply Negative Supply EP Exposed pad must be connected to a sufficient thermal conduit. Electrically connect to the most negative supply or leave floating open. Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 Condition 2 Rating Unit VCC PECL Mode Power Supply VEE = 0 V 8 V VEE NECL Mode Power Supply VCC = 0 V -8 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 -6 V V Iout Output Current Continuous Surge 50 100 mA mA TA Operating Temperature Range -40 to +85 C Tstg Storage Temperature Range -65 to +150 C qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm 8 SOIC 8 SOIC 190 130 C/W C/W qJC Thermal Resistance (Junction-to-Case) Standard Board 8 SOIC 41 to 44 C/W qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm 8 TSSOP 8 TSSOP 185 140 C/W C/W qJC Thermal Resistance (Junction-to-Case) Standard Board 8 TSSOP 41 to 44 5% C/W Tsol Wave Solder <2 to 3 sec @ 248C <2 to 3 sec @ 260C 265 265 C Pb Pb-Free VI VCC VI VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 2 MC10EL52, MC100EL52 Table 4. 10EL SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; VEE = 0 V (Note 1) -40C Symbol Characteristic Min 25C Typ Max 21 25 Min 85C Typ Max 21 25 Min Typ Max Unit 21 25 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 5) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mV VOL Output LOW Voltage (Note 2) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mV VIH Input HIGH Voltage (Single-Ended) 3770 4110 3870 4190 3940 4280 mV VIL Input LOW Voltage (Single-Ended) 3050 3500 3050 3520 3050 3555 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) D CLK 3.4 2.5 4.6 4.4 3.4 2.5 4.6 4.4 3.4 2.5 4.6 4.4 IIH Input HIGH Current IIL Input LOW Current V 150 0.5 150 0.5 150 0.3 mA mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / -0.5 V for +25C and +85C. or VEE can vary +0.06 V / -0.5 V for -40C. 2. Outputs are terminated through a 50 ohm resistor to VCC - 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 5. 10EL SERIES NECL DC CHARACTERISTICS VCC = 0 V; VEE = -5.0 V (Note 4) -40C Symbol Characteristic Typ Max 21 25 -1080 -990 -890 Output LOW Voltage (Note 5) -1950 -1800 VIH Input HIGH Voltage (Single-Ended) VIL Input LOW Voltage (Single-Ended) VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) D CLK IIH Input HIGH Current IIL Input LOW Current IEE Power Supply Current VOH Output HIGH Voltage (Note 5) VOL Min 25C Min 85C Typ Max 21 25 -980 -895 -810 -1650 -1950 -1790 -1230 -890 -1950 -1.6 -2.5 Min Typ Max Unit 21 25 mA -910 -815 -720 mV -1630 -1950 -1773 -1595 mV -1130 -810 -1060 -720 mV -1500 -1950 -1480 -1950 -1445 mV -0.4 -0.6 -1.6 -2.5 -0.4 -0.6 -1.6 -2.5 -0.4 -0.6 V 150 0.5 150 0.5 150 0.3 mA mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / -0.5 V for +25C and +85C. or VEE can vary +0.06 V / -0.5 V for -40C. 5. Outputs are terminated through a 50 ohm resistor to VCC - 2.0 V. 6. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. http://onsemi.com 3 MC10EL52, MC100EL52 Table 6. 100EL SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; VEE = 0 V (Note 7) -40C Symbol Characteristic Min 25C Typ Max 21 25 Min 85C Typ Max 21 25 Min Typ Max Unit 24 29 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 8) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mV VOL Output LOW Voltage (Note 8) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mV VIH Input HIGH Voltage (Single-Ended) 3835 4120 3835 4120 3835 4120 mV VIL Input LOW Voltage (Single-Ended) 3190 3525 3190 3525 3190 3525 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) D CLK 2.6 2.5 4.6 4.2 2.6 2.5 4.6 4.2 2.6 2.5 4.6 4.2 IIH Input HIGH Current IIL Input LOW Current V 150 0.5 150 0.5 150 0.5 mA mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 7. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / -0.5 V. 8. Outputs are terminated through a 50 ohm resistor to VCC - 2.0 V. 9. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 7. 100EL SERIES NECL DC CHARACTERISTICS VCC = 0 V; VEE = -5.0 V (Note 10) -40C Symbol Characteristic Min 25C Typ Max 21 25 Min 85C Typ Max 21 25 Min Typ Max Unit 24 29 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 11) -1085 -1005 -880 -1025 -955 -880 -1025 -955 -880 mV VOL Output LOW Voltage (Note 11) -1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 mV VIH Input HIGH Voltage (Single-Ended) -1165 -880 -1165 -880 -1165 -880 mV VIL Input LOW Voltage (Single-Ended) -1810 -1475 -1810 -1475 -1810 -1475 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 3) D CLK -2.4 -2.5 -0.4 -0.8 -2.4 -2.5 -0.4 -0.8 -2.4 -2.5 -0.4 -0.8 IIH Input HIGH Current IIL Input LOW Current V 150 0.5 150 0.5 150 0.5 mA mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 10. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / -0.5 V. 11. Outputs are terminated through a 50 ohm resistor to VCC - 2.0 V. 12. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. http://onsemi.com 4 MC10EL52, MC100EL52 Table 8. AC CHARACTERISTICS VCC = 5.0 V; VEE = 0 V or VCC = 0 V; VEE = -5.0 V (Note 13) -40C Min Typ fmax Symbol Maximum Toggle Frequency Characteristic 1.8 2.5 tPLH tPHL Propagation Delay to Output CLK 225 335 tS Setup Time 125 tH Hold Time 150 tPW Minimum Pulse Width 400 VPP Input Swing (Note 14) 150 tJITTER Cycle-to-Cycle Jitter tr tf Output Rise/Fall Times Q (20% - 80%) 25C Max Min Typ 2.2 2.8 275 365 0 125 50 150 515 Max Min Typ 2.2 2.8 320 410 0 125 0 ps 50 150 50 ps 465 400 1000 225 1000 100 510 1000 TBD 225 350 100 Unit GHz ps ps 150 TBD 350 Max 400 150 TBD 100 85C 225 mV ps 350 ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 13. 10 Series: VEE can vary +0.25 V / -0.5 V for +25C and +85C. or VEE can vary +0.06 V / -0.5 V for -40C 100 Series: VEE can vary +0.8 V / -0.5 V. 14. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of 40. Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC - 3.0 V Figure 2. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D - Termination of ECL Logic Devices.) http://onsemi.com 5 MC10EL52, MC100EL52 ORDERING INFORMATION Package Shipping SOIC-8 98 Units / Rail MC10EL52DG SOIC-8 (Pb-Free) 98 Units / Rail MC10EL52DR2 SOIC-8 2500 / Tape & Reel MC10EL52DR2G SOIC-8 (Pb-Free) 2500 / Tape & Reel MC10EL52DT TSSOP-8 100 Units / Rail MC10EL52DTG TSSOP-8 (Pb-Free) 100 Units / Rail MC10EL52DTR2 TSSOP-8 2500 / Tape & Reel MC10EL52DTR2G TSSOP-8 (Pb-Free) 2500 / Tape & Reel MC10EL52MNR4 DFN8 1000 / Tape & Reel DFN8 (Pb-Free) 1000 / Tape & Reel SOIC-8 98 Units / Rail MC100EL52DG SOIC-8 (Pb-Free) 98 Units / Rail MC100EL52DR2 SOIC-8 2500 / Tape & Reel MC100EL52DR2G SOIC-8 (Pb-Free) 2500 / Tape & Reel MC100EL52DT TSSOP-8 100 Units / Rail MC100EL52DTG TSSOP-8 (Pb-Free) 100 Units / Rail MC100EL52DTR2 TSSOP-8 2500 / Tape & Reel MC100EL52DTR2G TSSOP-8 (Pb-Free) 2500 / Tape & Reel MC100EL52MNR4 DFN8 1000 / Tape & Reel DFN8 (Pb-Free) 1000 / Tape & Reel Device MC10EL52D MC10EL52MNR4G MC100EL52D MC100EL52MNR4G For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D - ECL Clock Distribution Techniques AN1406/D - Designing with PECL (ECL at +5.0 V) AN1503/D - ECLinPSt I/O SPiCE Modeling Kit AN1504/D - Metastability and the ECLinPS Family AN1568/D - Interfacing Between LVDS and ECL AN1672/D - The ECL Translator Guide AND8001/D - Odd Number Counters Design AND8002/D - Marking and Date Codes AND8020/D - Termination of ECL Logic Devices AND8066/D - Interfacing with ECLinPS AND8090/D - AC Characteristics of ECL Devices http://onsemi.com 6 MC10EL52, MC100EL52 PACKAGE DIMENSIONS SOIC-8 NB CASE 751-07 ISSUE AH -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 1 0.25 (0.010) M Y M 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- H 0.10 (0.004) D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC10EL52, MC100EL52 PACKAGE DIMENSIONS TSSOP-8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R-02 ISSUE A 8x 0.15 (0.006) T U 0.10 (0.004) S 2X L/2 L 8 5 1 PIN 1 IDENT 0.15 (0.006) T U K REF S M T U V S 0.25 (0.010) B -U- 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S M A -V- F DETAIL E C 0.10 (0.004) -T- SEATING PLANE D -W- G DETAIL E http://onsemi.com 8 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ MC10EL52, MC100EL52 PACKAGE DIMENSIONS DFN8 CASE 506AA-01 ISSUE D D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994 . 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B PIN ONE REFERENCE 2X 0.10 C 2X CCCC CCCC CCCC CCCC 0.10 C TOP VIEW 0.08 C SEATING PLANE MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 2.00 BSC 1.10 1.30 2.00 BSC 0.70 0.90 0.50 BSC 0.20 --- 0.25 0.35 A 0.10 C 8X DIM A A1 A3 b D D2 E E2 e K L E (A3) SIDE VIEW A1 C D2 e e/2 4 1 8X L E2 K 8 5 8X b 0.10 C A B 0.05 C NOTE 3 BOTTOM VIEW ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EL52/D