2017.12y
High performance miniature circular connectors
HR10 Series
Features
1.
A simple, yet highly reliable design for
compact, high density applications
Although small in size, the HR10 series are full
featured connectors with a well integrated design.
2. Extremely easy mating/unmating
operations
Easy to operable, the single-action push-pull lock
structure allows for quick and efficient locking and
unlocking.
Product Specifi cations
Ratings
Shell size No. of contacts Rated current
7
4
5
6
2A
10 10
12 2A
13 20 2A
Ratings
Shell size No. of contacts Rated voltage
7
4
5
6
AC150V, DC200V
AC100V, DC140V
AC100V, DC140V
10 10
12 AC100V, DC140V
13 20 AC100V, DC140V
Ratings Operation temperature range -25 to +85ç
Storage temperature range -10 to +60ç
Items Specifications Conditions
1. Contact resistance 10mø min. Measured at DC 1A
2. Insulation resistance 1,000Mø min. Measured at DC 100V
3. Withstanding voltage No flashover or dielectric breakdown. AC 300V for one minute, 4 contacts : AC 500V for 1 minute
4. Vibration resistance No electrical discontinuity of 10µs or greater 10 to 55Hz/cycle, amplitude : 0.75mm, 3 axis directions,
for 2 hours each
5. Shock resistance No electrical discontinuity of 10µs or greater Acceleration : 490m/s2, duration : 11ms 3 directions,
3 times each
6. Mating Cycles Contact resistance : 15mø min. 1,000 times
7. Temperature cycle Insulation resistance : 1,000Mø min.
-55ç : 30minutes➝Normal temperature : 10 to 15 minutes➝
85ç : 30minutes➝Normal temperature :
10 to 15minutes, left for 5 cycles.
8. Humidity resistance 5Mø min. (at high humidity)
50Mø min. (at dry)
Temperature : 40ç, relative humidity : 90 to 95%,
left for 96 hours
In cases where the application will demand a high level of reliability, such as automotive,
please contact a company representative for further information.
1
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Materials / Finish
Items Material Finish Remarks
Exterior Zinc alloy, brass Matte finished nickel plating ----------------
Insulator Polyamide resin, PBT resin ---------------- Blue, Black
Contact Copper alloy HR10 : Gold plating
HR10A : Silver plating ----------------
qModel name : Indicates the HR10A Series. The part type is identified as follows.
HR10A : Lower cost type
HR10G : Shield type
HR10B : Coaxial contact type
wShell size : The shell size is the outer shell diameter or the mating interface end of the plug.
eShell type
P : Plug
R : Receptacle
J : Jack
rNumber of contacts
tContact form
P : Male contact
S : Female contact
yContact termination method:
None : Solder termination
C : Crimp termination
uOther specifications : A two-digit character is added to indicate other specifications as needed.
Product Number Structure
Refer to the chart below when determining the product specifications from the product number.
Please select from the product numbers listed in this catalog when placing orders.
HR10A -7P-3PC (**)
qwertyu
2
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Diagrams of Connectors in Combination
Notes
1 : When using a plug with male terminal, be sure to use a receptacle or jack fi tted with female terminal.
2 : Standard fi nish of the terminal is gold plating for the HR10, and silver plating for the HR10A and HR10G.
Be sure to use male and female connectors of the same plating.
Male Pin side Female Pin side
(HR10 Type Plug)
(HR10 Type Jack)
(HR10B Type Receptacle)
(HR10A-[ ]T Type Receptacle)
(HR10A-[ ]T Type Jack)
(HR10A Type Jack)
(HR10 • HR10A
HR10G Type Receptacle)
(HR10A Type Plug)
(HR10B Type Plug)
(HR10A-[ ]T Type Plug)
3
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
HR10 type
HR10 type connectors, use a gold plated contact as the standard plating specification. Silver plating is used on the contacts
for other series such as HR10A and HR10G. To avoid mixing gold and silver contacts, please be sure to confirm the plating
specification when using HR10 type connectors with HR10A or HR10G connectors.
Plug
ØD
A Max
ØC
ØB
Unit : mm
Part No. HRS No. No. of Contacts A ØB ØC ØD Weight
HR10-7P-4P(73) 110-0021-6 73
4
28.5 11 7 5.2 8g
HR10-7P-4S(73) 110-0022-9 73
HR10-7P-6P(73) 110-0023-1 73
6
HR10-7P-6S(73) 110-0024-4 73
HR10-10P-12P(73) 110-0025-7 73
12
32.5 14 9.5 7.2 15g
HR10-10P-12S(73) 110-0026-0 73
(Representative example)
HR10-7P-6S(73)
Receptacle
E(HEX)
D
A
5.76.3
ØC
ØB
Unit : mm
Part No. HRS No. No. of Contacts A ØB ØC D E Weight
HR10-7R-4S(73) 110-0031-0 73 4
14 11 8.85 M8×0.5 10 3.5g
HR10-7R-4P(73) 110-0032-2 73
HR10-7R-6S(73) 110-0033-5 73 6
HR10-7R-6P(73) 110-0034-8 73
HR10-10R-12S(73) 110-0035-0 73 12 16 14 11.9 M11×0.75 13 6g
HR10-10R-12P(73) 110-0036-3 73
Remarks : For mounting holes, see page 20.
(Representative example)
HR10-7R-6S(73)
4
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Receptacle (PCB dip type)
D(HEX)
C
Dip post dia.
Ø0.55
G
F5.7
E
ØA
ØB
Unit : mm
Part No. HRS No.
No. of Contacts
ØA ØB C D E F G
Weight
HR10-7R-4SA(73) 110-0059-9 73 4
11 8.85 M8×0.5 10
6.3 0.5 15.5
3gHR10-7R-6SA(73) 110-0050-4 73 6
HR10-7R-6PA(73) 110-0061-0 73
HR10-10R-12SA(73) 110-0049-5 73 12 14 11.9 M11×0.75 13 5g
HR10-10R-12PA(73) 110-0055-8 73
Remarks : 1. For mounting holes, see page 20.
2. For dip post arrangement, see page 16.
(Representative example)
HR10-7R-6SA(73)
Jack
ØD
5.5
A Max
ØB
ØC
Unit : mm
Part No. HRS No. No. of Contacts A ØB ØC ØD Weight
HR10-7J-4S(73) 110-0027-2 73 4
28.5 11 8.85 5.2 7g
HR10-7J-4P(73) 110-0028-5 73
HR10-7J-6S(73) 110-0029-8 73 6
HR10-7J-6P(73) 110-0030-7 73
HR10-10J-12S(73) 110-0037-6 73 12 32.5 14 11.9 7.2 14g
HR10-10J-12P(73) 110-0038-9 73
(Representative example)
HR10-7J-6S(73)
5
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Plug (Solder type)
ØB
ØC
ØD
A
Unit : mm
Part No. HRS No. No. of Contacts A ØB ØC ØD Weight
HR10A-7P-4P(73) 110-0301-2 73 4
35 11.5 7 5 9g
HR10A-7P-4S(73) 110-0302-5 73
HR10A-7P-5P(73) 110-0318-5 73 5
HR10A-7P-5S(73) 110-0319-8 73
HR10A-7P-6P(73) 110-0303-8 73 6
HR10A-7P-6S(73) 110-0304-0 73
HR10A-10P-10P(73) 110-0407-3 73 10
43 14.7 9.5
7
16g
HR10A-10P-10S(73) 110-0408-6 73
HR10A-10P-12P(73) 110-0401-7 73 12
HR10A-10P-12S(73) 110-0402-0 73
HR10A-13P-20P(73) 110-0713-0 73 20 59 19 13 37g
HR10A-13P-20S(73) 110-0716-8 73
(Representative example)
HR10A-7P-6P(73)
Plug(Crimp type)
ØC
ØB
ØD
A
Unit : mm
Part No. HRS No. No. of Contacts A ØB ØC ØD Weight
HR10A-7P-4PC(73) 110-0501-1 73 4
35 11.5 7 5 9g
HR10A-7P-4SC(73) 110-0502-4 73
HR10A-7P-6PC(73) 110-0503-7 73 6
HR10A-7P-6SC(73) 110-0504-0 73
HR10A-10P-10PC(73) 110-0601-6 73 10
43 14.7 9.5
7
16g
HR10A-10P-10SC(73) 110-0602-9 73
HR10A-10P-12PC(73) 110-0603-1 73 12
HR10A-10P-12SC(73) 110-0604-4 73
HR10A-13P-20PC(73) 110-0701-0 73 20 59 19 13 37g
HR10A-13P-20SC(73) 110-0702-3 73
(Representative example)
HR10A-7P-6PC(73)
HR10A•10G Types
HR10A connectors are a lower-cost version, yet still provide a high "Value Add" while preserving the superior characteristics
of the HR10 connectors. Cable clamps are crimped using a special crimping tool, and the shells have a rubber boot which
provides a flexible design that helps to prevent cable twisting.
The HR10G connector is a shielded type connector which has an internal contacting structure between the plug shell and
receptacle shell.
Contacts in both HR10A and 10G connectors are silver plated as standard.
6
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Unit : mm
Part No. HRS No.
No. of Contacts
ØA ØB C D E F
Weight
Remarks
HR10A-7R-4SC(73) 110-0506-5 73 4
11 8.85 M8×0.5 10
6.3
12
3g
HR10A-7R-4PC(73) 110-0505-2 73 12.2
HR10A-7R-6SC(73) 110-0508-0 73 612
HR10A-7R-6PC(73) 110-0507-8 73 12.2
HR10A-10R-10SC(71) 110-0606-0 71 10
14 11.9 M11×0.75 13
12
5g
HR10A-10R-10PC(71) 110-0605-7 71 12.2
HR10A-10R-12SC(71) 110-0608-5 71 12 12
HR10A-10R-12PC(71) 110-0607-2 71 12.2
HR10A-13R-20SC(73) 110-0703-6 73 20 18 15.4 M14×0.75 17 9.3 15 8g
HR10A-13R-20PC(73) 110-0704-9 73
HR10G-7R-4SC(73) 110-1701-6 73 4
11 8.85 M8×0.5 10
6.3
12
3g
Shield type
HR10G-7R-4PC(73) 110-1702-9 73 12.2
HR10G-7R-6SC(73) 110-1705-7 73 612
HR10G-7R-6PC(73) 110-1706-0 73 12.2
HR10G-10R-10SC(71) 110-1707-2 71 10
14 11.9 M11×0.75 13
12
5g
HR10G-10R-10PC(71) 110-1708-5 71 12.2
HR10G-10R-12SC(71) 110-1709-8 71 12 12
HR10G-10R-12PC(71) 110-1710-7 71 12.2
HR10G-13R-20SC(73) 110-1711-0 73 20 18 15.4 M14×0.75 17 9.3 15 8g
HR10G-13R-20PC(73) 110-1712-2 73
Remarks : For mounting holes, see page 20.
Receptacle (Solder type)
E(HEX)
D
ØB
ØC
A
5.7F
(Representative example)
Unit : mm
Part No. HRS No.
No. of Contacts
AØBØC D EE
Weight
Remarks
HR10A-7R-4S(73) 110-0305-3 73 4
14 11 8.85 M8×0.5 10
6.3
3g
HR10A-7R-4P(73) 110-0306-6 73
HR10A-7R-5S(73) 110-0320-7 73 5
HR10A-7R-5P(73) 110-0321-0 73
HR10A-7R-6S(73) 110-0307-9 73 6
HR10A-7R-6P(73) 110-0308-1 73
HR10A-10R-10S(71) 110-0409-9 71 10
16 14 11.9 M11×0.75 13 5g
HR10A-10R-10P(73) 110-0410-8 73
HR10A-10R-12S(71) 110-0403-2 71 12
HR10A-10R-12P(73) 110-0404-5 73
HR10A-13R-20S(73) 110-0714-2 73 20 19.2 18 15.4 M14×0.75 17 9.3 8g
HR10A-13R-20P(73) 110-0715-5 73 20.2
HR10G-7R-4S(73) 110-1601-1 73 4
14 11 8.85 M8×0.5 10
6.3
3g
Shield type
HR10G-7R-4P(73) 110-1602-4 73
HR10G-7R-6S(73) 110-1605-2 73 6
HR10G-7R-6P(73) 110-1606-5 73
HR10G-10R-10S(71) 110-1607-8 71 10
16 14 11.9 M11×0.75 13 5g
HR10G-10R-10P(73) 110-1608-0 73
HR10G-10R-12S(71) 110-1609-3 71 12
HR10G-10R-12P(73) 110-1610-2 73
Remarks : For mounting holes, see page 20.
HR10A-7R-6S(73)
Receptacle (Crimp type)
C
D(HEX)
E
F
ØB
ØA
(Representative example)
HR10A-10R-12SC(71)
7
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Dust cap
B
ØA
1
0.2
ØD
ØC
ØE
2
HR10-7R-C
Receptacle (Dip type)
D(HEX)
C
Dip post dia.
0.2∞0.5
ØA
ØB
G
F5.7E
Unit : mm
Part No. HRS No.
No. of
Contacts
ØA ØB C D E F G
Weight Remarks
HR10A-7R-4SB(73)
110-0314-4 73 4
11 8.85 M8×0.5 10
6.3 0.5 15.6
3g
HR10A-7R-4PB(73)
110-0315-7 73
HR10A-7R-5SB(73)
110-0322-2 73 5
HR10A-7R-6SB(73)
110-0316-0 73 6
HR10A-7R-6PB(73)
110-0317-2 73
5g
HR10A-10R-10SB(71)
110-0413-6 71 10
14 11.9 M11×0.75 13
HR10A-10R-10PB(71)
110-0414-9 71
HR10A-10R-12SB(71)
110-0415-1 71 12
HR10A-10R-12PB(71)
110-0416-4 71
HR10A-13R-20SB(73)
110-0707-7 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8g
HR10A-13R-20PB(73)
110-0708-0 73
HR10G-7R-4SB(73)
110-1801-0 73 4
11 8.85 M8×0.5 10
6.3 0.5 15.6
3g
Shield
type
HR10G-7R-4PB(73)
110-1802-3 73
HR10G-7R-6SB(73)
110-1805-1 73 6
HR10G-7R-6PB(73)
110-1806-4 73
HR10G-10R-10SB(71)
110-1807-7 71 10
14 11.9 M11×0.75 13 5g
HR10G-10R-10PB(71)
110-1808-0 71
HR10G-10R-12SB(71)
110-1809-2 71 12
HR10G-10R-12PB(71)
110-1810-1 71
HR10G-13R-20SB(73)
110-1811-4 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8g
HR10G-13R-20PB(73)
110-1812-7 73
Remarks : 1. For mounting holes, see page 20.
2. For dip post arrangement, see page 16.
Unit : mm
Part No. HRS No. ØA B ØC ØD ØE
HR10-7R-C 110-0058-6 00 11 7 8 11.2 13
HR10-10R-C 110-0052-0 00 14 8.5 10.8 14.1 15
HR10A-13R-C 110-0452-8 00 17.5 11.5 14 18.1 19
(Representative example)
(Representative example)
HR10A-7R-6SB(73)
8
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Jack (Solder type)
ØC
ØB
5.5
A
ØD
(Representative example)
Unit : mm
Part No. HRS No.
No. of Contacts
A ØB ØC ØD Weight
HR10A-7J-4S(73) 110-0309-4 73 4
35.3 11 8.85 5 9g
HR10A-7J-4P(73) 110-0310-3 73
HR10A-7J-6S(73) 110-0311-6 73 6
HR10A-7J-6P(73) 110-0312-9 73
HR10A-10J-10S(73) 110-0411-0 73 10
43.5 14 11.9 7 16g
HR10A-10J-10P(73) 110-0412-3 73
HR10A-10J-12S(73) 110-0405-8 73 12
HR10A-10J-12P(73) 110-0406-0 73
HR10A-7J-6S(73)
Jack (Crimp type)
ØC
ØB
D
A
ØE
Unit : mm
Part No. HRS No.
No. of Contacts
A ØB ØC D ØE Weight
HR10A-7J-4SC(73) 110-0510-2 73 4 35.3 11 8.85
5.5
59g
HR10A-7J-6SC(73) 110-0512-8 73 6
HR10A-10J-10SC(73) 110-0610-7 73 10 43.5 14 11.9
7
16g
HR10A-10J-12SC(73) 110-0612-2 73 12
HR10A-13J-20SC(73) 110-0705-1 73 20 58.5 18 15.4 8.5 37g
HR10A-13J-20PC(73) 110-0706-4 73
(Representative example)
HR10A-7J-6SC(73)
9
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Plug
HR10B Type Connector
The HR10B connector combines 10 signal lines and one coaxial contact in the standard number 10 shell. Performance
specifications for the coaxial contacts are on the 11 page.
Ø14.7
A
ØB
Unit : mm
Part No. HRS No. A ØB Applicable coaxial contact
HR10B-10P-10PC(73) 110-0901-0 73 50 5 HR10B-2.5CJ(73)
HR10B-10PA-10PC(73) 110-0906-3 73 43 7
(Representative example)
HR10B-10P-10PC(73)
Receptacle
13(HEX)
M11∞0.75
Ø11.9
Ø14
6.3
12
Unit : mm
Part No. HRS No. Applicable coaxial contact
HR10B-10R-10SC(71) 110-0902-2 71 HR10B-2.5CP(73)
Remarks : For mounting holes, see page 20.
(Representative example)
HR10B-10R-10SC(71)
10
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Plug
(clamp)
4.1
5.2 3.6
Ø3.8
7.1
18.05
Ø4.2
Ø1.1
(Representative example)
Unit : mm
Part No. HRS No. Applicable cable Applicable connector
HR10B-2.5CP(73) 110-0904-8 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10R-10SC(71)
HR10B-2.5CP(73)
Jack
(clamp)
Ø2.65
7.25
18.2
Ø4.2
Ø1.1
4.1
5.2 3.6
(Representative example)
Unit : mm
Part No. HRS No. Applicable cable Applicable connector
HR10B-2.5CJ(73) 110-0903-5 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10P-10PC(73)
HR10B-2.5CJ(73)
Coaxial contacts
The coaxial contacts shown here are for use with the HR10B connector.These contacts have locking barbs and are inserted
from the rear of connector.Please use the following information to select the correct terminals.
Materials / Finish Performance
Part Material Finish
Plug shell Brass Gold plating
Jack shell
Insulator Tetrafl uoride resin
Male pin Phosphor bronze Gold plating
Female pin Beryllium copper
Description Test data
Impedance
50ø
Insulation resistance 1000Mø or more at DC250V
Contact resistance
Center 6.5mø or less and outer 4mø or less at DC1A
Withstanding voltage AC250V r.m.s for 1minute
V.S.W.R
1.3 or less for 0 to 1000MHz
Pull force
4.9N (500gf) or more
11
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Cable connecting methods
11±0.5
1.4±0.2
3.7±0.2
(2.5)
Slit cable outer jaket
2 pieces (180° reverse side)
1. Dimensions for cable end treatment are shown in Fig 1.
2. Termination is described below.
(1) Strip cable outer jacket as indicated.
(2) Slit outer jacket on both sides per Fig.1.
(3) Fold back outer cover.
(4) Remove insulator from cable.
1. Cable end treatment
Fig.1
Male pin
Soldering
Should fix flush
Contact fixing jig such as vise
1. Solder male pin to cable center conductor as indicated in Fig.2.
(1) Pre-solder the solder pot of pin with Ø0.5mm string solder.
(2) Male pin should fit flush against the cable insulator as
shown.
(3) Remove any excess solder from the pin with a knife.This
surface must be smooth.
(4) A properly soldered terminal will yield 500gf when stretched.
2. Soldering male pin to cable center conductor
Fig.2
Clamp
15±0.2
Connector
Remove excess insulator material
(remaining after clamping is complated)
with a knife or aimilarobject.
1. Insert the cable into the connector and make sure to push it
all the way in. To confirm that the cable is fully inserted,
make sure that the depth is 1.5 ± 0.2mm by measuring from
the end of the connector to the tip of the male contact by
using a vernier calipers or other suitable measuring device.
2. Use the HR10-TC-01 tool to crimp the metal fitting to the
cable.
3. Crimping cable outer conductor
Fig.3
HR10B-2.5CP(73)
HR10B-2.5CJ(73)
12
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
HR10A-( )T Type (Threaded Coupling Type)
HR10A-( )T connector is a new product having a threaded coupling locking mechanism. Electric parformance is same as
HR10 and HR10A push-pull locking type connectors.
Plug (Crimp type)
43
Ø7
Ø17
Ø9.5
M13∞0.75
Unit : mm
Part No. HRS No.
No. of Contacts
HR10A-10TP-12PC(73) 110-0455-6 73 12
HR10A-10TP-12PC(73) (Representative example)
(Representative example)
Plug (Solder type)
ØC
B
ØA
D
ØE
HR10A-10TP-12P(73)
Unit : mm
Part No. HRS No.
No. of Contacts
ØA B ØC D ØE Remarks
HR10A-7TP-6P(73) 110-0331-3 73 6 12 M10×0.75 7 35 5
HR10A-7TP-6P(74) 110-0331-3 74 Gold plating
HR10A-10TP-12P(73) 110-0432-0 73
12
17 M13×0.75
9.5
43 7
HR10A-10TPA-12S(73) 110-0446-5 73
HR10A-10WTP-12P(73) 110-1101-9 73 15 M12×0.75 45.8 6.5 *
HR10A-10WTP-12S(73) 110-1106-2 73
HR10A-13TPD-20P(73) 110-1015-9 73 20 20 M17×1 13 56.5 7
*Waterproof plug need resin fi lling inside when connector assembly.
When mated, the connector against water penetration.
13
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Unit : mm
Part No. HRS No.
No. of Contacts
ØA B C DEFG H
HR10A-7TR-6SA(73) 110-0330-0 73 6 11 M10×0.75
M8×0.5
10
6.3 0.5
15.5 Ø0.55
HR10A-10TR-12SB(73) 110-0433-3 73
12 14 M13×0.75
M11×0.75
13
15.6
0.2×0.5
HR10A-10TR-12PB(73) 110-0457-1 73 15.5
HR10A-10TR-12PE(73) 110-0445-2 73 14
HR10A-10WTR-12SB(73) 110-1102-1 73 M12×0.75
M10.5×0.75
6.8 015.6
HR10A-13TR-20SB(73) 110-1014-6 73 20 18 M17×1
M14×0.75
17 9.3 17.8
Remarks : 1.For mounting holes, see page 15. However, 7TR size shell be referred to page 20 on the shell size 7.
2.For dip post arrangement, see page 16.
Receptacle (Solder type)
A
F(HEX)
C
ØD
B5.7
E
Unit : mm
Part No. HRS No.
No. of Contacts
A B C ØD E F Remarks
HR10-7TR-6S(73) 110-0089-0 73 6 M10×0.75 6.3 M8×0.5 11 14 10 Gold plating
HR10A-10TR-12S(73) 110-0453-0 73 12 M13×0.75 M11×0.75 14 16 13
HR10A-10WTR-12S(73) 110-1104-7 73 M12×0.75 6.8 M10.5×0.75
Remarks : For mounting hole, see page 15(10TR,10WTR) 20(7TR).
HR10A-10TR-12S(73) (Representative example)
Receptacle (Crimp type)
D
E
F(HEX)
ØA
B
C
Unit : mm
Part No. HRS No.
No. of Contacts
ØA B C D E F
HR10A-10TR-12SC(73) 110-0456-9 73 12 14 12 6.3 M13×0.75 M11×0.75 13
HR10A-13TR-20SC(73) 110-1002-7 73 20 18 15 9.3 M17×1 M14×0.75 17
Remarks : For mounting hole, see page 15
HR10A-10TR-12SC(73) (Representative example)
Receptacle (Dip type)
C
D(HEX)
B
Dip post
H
ØA
E5.7 F
G
HR10A-10TR-12PB(73) (Representative example)
14
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Jack (Solder type)
Unit : mm
Part No. HRS No.
No. of Contacts
ØA B ØC D Remarks
HR10A-10TJ-12S(73) 110-0436-1 73
12 14.7 41.3 7 M13×0.75
HR10A-10TJ-12P(73) 110-0459-7 73
HR10A-10WTJ-12S(73) 110-1103-4 73 14 46.5 6.5 M12×0.75 *
*Waterproof jack need resin fi lling inside when connector assembly.
When mated, the connector against water penetration.
D
ØA
B
ØC
(Representative example)
HR10A-10TJ-12S(73)
Panel mounting hole dimensions (Screw coupling)
The mounting hole dimensions shown below are for connectors to be tightened by a hexagonal nut from the back of the
panel. The dimensions below apply only to the HR10A-( )T and not the 7TR. For the dimensions of connectors of other
types, see page 20.
9.6 +0.1
0
Ø11.1
+0.1
0
Ø10.6+0.1
0
Ø14.1
+0.1
0
Type HR10A-10TR
(Panel thickness 1 to 2mm)
Type HR10A-10TR
(Panel thickness 1 to 2mm)
9.6 +0.1
0
Type HR10A-10WTR
(Panel thickness 1 to 2mm)
8.6 +0.1
0
1.6 +0.1
0
Type HR10A-13TR
(Panel thickness 1 to 1.5mm)
15
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Male contact
Female contact
A
A
1.15
1.2
1
10
A
A
10
1
1.15
1.2
Receptacle dip post arrangement dimensions
Contact
Unit : mm
Type Part No. HRS No. Type of plating Applicable
cable
Loose
contact
HR10-PC-111 110-0515 6
Partial gold plating
26 to 30
AWG
HR10-PC-112 110-0513 0
Silver plating
Reel
contact
HR10-PC-211 110-0516 9
Partial gold plating
HR10-PC-212 110-0514 3
Silver plating
Remarks : 1. Use cables with a coating outside diameter of 1mm or less.
2. Loose piece terminal are available in packs. Each pack
contains 100 terminals. Strip terminals are available in
reels. Each reel contains 10,000 terminals.
Unit : mm
Type Part No. HRS No. Type of plating Applicable
cable
Loose
contact
HR12-SC-111 112-0410 0
Partial gold plating
26 to 30
AWG
HR12-SC-112 112-0411 3
Silver plating
Reel
contact
HR12-SC-211 112-0407 6
Partial gold plating
HR12-SC-212 112-0408 9
Silver plating
Remarks : 1. Use cables with a coating outside diameter of 1mm or less.
2. Loose piece terminal are available in packs. Each pack
contains 100 terminals. Strip terminals are available in
reels. Each reel contains 10,000 terminals.
Remarks : 1. The above fi gures are views from the mating side and pin inserts from the wiring-connection side.
2. Dimensional tolerance of ±0.05 is recommended for the board arrangement.
1.131.13
1.561.56
1.13
7-size 4 cores 7-size 6 cores
10-size 10 cores 10-size 12 cores
13-size 20 cores
1.13 0.9 0.9
1.8 1.8
(4 Places)
(6 Places)
(10 Places)
(12 Places)
(20 Places)
23
41
1.8 1.8
1.8 1.8
7-size 5 cores
(5 Places)
2
3
5
4
1
16
2
3
4
5
2.5
2.58
2.38 2.38
0.950.95
2.75
2.11
0.55
0.48
2.85 2.85
0.95 0.95
1.1
1.38
2.5
2.55 2.55
1
1 1 1.77 1.77 0.8
2.4
4
0.8
2.4
4
2.71 2.71
1
11
2
910
8
7
6
54
3
2
21
5678910
161514131211
17 18 19 20
34
3
4
5
6
712 11
10
9
8
Ø0.8＋0.1
0
Ø0.8＋0.1
0
Ø0.8＋0.1
0
Ø0.8＋0.1
0
Ø0.8＋0.1
0
Ø0.8＋0.1
0
16
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Tools
Type Item Part No. HRS No. Applicable terminal Applicable cable
Manual Manual crimping tool HT802/HR12-SC-1 150-0400-3 HR10-PC-112 26 to 30AWG
HR12-SC-112
Automatic
Automatic crimping
machine body CM-105C 901-0001-0 _______ _______
Applicator AP105-HR12-1 901-2015-9
HR10-PC-211
212
26 to 30AWG
HR12-SC-211
212
Cable crimping tool HR10-TC-01 150-0036-2 _______
(HR10B-2.5CP(73),
HR10B-2.5CJ(73))
HR10A-TC-02 150-0041-2 Ø5, Ø7
Extractor
HR12-SC-TP 150-0050-3 HR12-SC-112
_______
HR12-SC-212
RP6-SC-TP 150-0039-0 HR10-PC-112
HR10-PC-212
HR10B-TP 150-0061-0 HR10B-2.5CP(73)
HR10B-2.5CJ(73)
(HT802/HR12-SC-1)
Hand Crimp Tool
(HR10A-TC-02)
Hand Cable Crimp Tool
(HR10B-TP)
Coaxial Contact Removal Tool
(HR12-SC-TP)
Auto Crimp Tool CM-105C
(RP6-SC-TP)
Extraction Tool
17
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
How to use a connector
HR10-10P-T02 HR10-10J-T04
Part No. HRS No. Applicable connector
HR10-7P-T01 150-0009-0 HR10-7P
HR10-10P-T02 150-0010-9 HR10-10P
HR10-7J-T03 150-0011-1 HR10-7J
HR10-10J-T04 150-0012-4 HR10-10J
HR10-13P-T05 150-0059-8 HR10-13P
HR10-13J-T06 150-0060-7 HR10-13J
Panel
Plug Cable
Receptacle
A
Panel
Plug Cable
Receptacle
A
Panel
B
Plug connection sleeve Cable
Panel
Plug connection sleeve
B
Cable
Connecting tools
When terminating the wires, use the jigs noted below for easy assembly / disassembly of the connector parts.
1.Inserting 2.Withdrawing
HR10 TYPEHR10A TYPE
Hold the plug at point A, align the plug guide with the
receptacle guide, and push the plug straight.
The plug will mate with the receptacle smoothly.
Hold the plug connection sleeve B and pull the sleeve
straight. The plug will come off easily.
18
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
HR10 TYPEHR10A TYPE
Cable assembly procedure on plug side
This applies also to the jack side assembly procedure.
No special procedure is given here for the receptacle side because no special procedure is necessary.
Table 2 spanner jaw distance
Size HR10 HR10A
7 8 7.5
10 11 9.5
1 3 ____ 1 3
Table 1
Size Tightening force
7 1.5N·m(15kg·cm)
10 2N·m(20kg·cm)
13
Table 3 cable end processing dimensions
Size
Dimension C
for HR10
Dimension D for HR10A
Solder type Crimp type
7 5.5 or less 10 15 to 20
10 7 or less 16
1 3 ____ 2 5
HR10 TYPE HR10A TYPE
1 Use cables with a nominal sectional area of 0.129mm2 (26 AWG) at the fi nish outside diameters applicable for each size.
2
After processing the cable ends according to the dimensions in the above drawings, fi t the parts to the cable as shown
in the drawings.
Fit the parts to the cable in the following order:
tightener, clamp washer, and plug body.
Fit the parts to the cable in the following order:
cord bushing and plug body.
3
(solder type)
Insert the P shell unit into the assembly tool stand and solder it.
(crimp type)
After crimping the appropriate crimp terminal to the cable core, insert the crimp terminal into the terminal hole in the P
shell unit.
4
Assemble the connector in the following steps.
1. Screw the plug body into the thread in the P shell unit
with the tightening force shown in Table 1 using a
torque wrench with a fi xed torque.
Before tightening the plug body,slacken part C so that
no load is applied to the soldered wires.
2. Apply the clamp washer to the bifurcated part of the
plug body, and then tighten the tightener until surface
B touches the plug body surface A.
Note : In order to prevent looseing, please apply an
adhesive at the thread of plug body.
1. Fix by caulking the clamp accompanying the cable
with the cable crimping tool(HR10A-TC-02)
2. Screw the plug body into the thread in the P shell until
with a tightening force shown in Table 1 using a torque
wrench with a fi xed torque. Before tightening the plug
body, slacken the part D so that no load is applied to
the soldered wires.
3. Tighten the set screw so that the tip of the screw
presses one of the two bosses on the clamp.
Fix the set screw with a tightening torque of 0.3N
(3kg·cm).
4. Attach the cord bushing to the plug body.
Note : In order to prevent looseing, please apply an
adhesive at the thread of plug body.
5 This completes the work.
For any question on using the plugs, contact our sales or engineering department.
P shell unit
Set screw
Boss
Clamp Plug body
Spanner jaw distance
Cord bushing
Cable
Ｄ
Ａ
2 or more
About 2 for solder type
2 for crimp type
0
-0.5
P shell unit Plug body
Bifurcated part
Clamp washer Tightener Cable
Face BFace A
Spanner jaw distance
About 2 C
19
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
Recommended Mounting Hole
Mounting hole dimension shown here is tight by hexagon nut from back side.
Contact Arrangement
A
B
ØC
7 size 10 size 13 size
A 1.6 2.6
B 5.1 6.6 8.6
C 8.1 11.1 14.1
Panel thickness 0.7 to 2 0.8 to 1.5
Shell size
Map mark
+0.1
0+0.1
0
+0.1
0+0.1
0+0.1
0
+0.1
0+0.1
0+0.1
0
Shell size 7 size 10 size
Contact arrangement
No. of contacts 4 5 6 10 12
Withstanding voltage AC500V for a minute AC300V for a minute
Current rating 2A
Insulation resistance MIN 1,000Mø
Contact resistance MAX 10mø
Solder pot inside dia. Ø0.8
Shell size 10 size 13 size
Contact arrangement
No. of contacts 10+coaxial contact 20
Withstanding voltage AC300V for a minute
Current rating 2A
Insulation resistance MIN 1,000Mø
Contact resistance MAX 30mø MAX 10mø
Solder pot inside dia. ____ Ø0.8
Notes 1. The contact arrangement shown here is the mating surface of socket insert assembled.
2. The withstanding voltage shown here is test voltage value.
3. The isulation resistance value is measured at DC100V.
4. The contact resistance value is measured at DC1A.
20
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 12/2017. Contents are subject to change without notice for the purpose of improvements.
Precautions
1. Switch off the power of the circuit before disconnecting or plugging-in the connector.
2. Use a connector with socket contacts at the power side of the circuit.
3. Make sure that the coupling is in completely locked position.
4. Cable clamping, cable rotation, and other forces may vary with the cable construction. Please make sure that your cable is
suitable for use with these connectors before usage and production.
5. This product series uses silver plated contacts. Silver reacts easily to exposure to sulfur gas so the below conditions may
cause tarnishing.
・Dusty environments
・Area with a high concentration area of gases such as sulfur dioxide gas, hydrogen sulfide gas, nitrogen dioxide gas
and so on.
Example; In close proximity to factory exhaust, automotive emissions, etc.
・Close to heaters, or in other areas marked by extreme temperature differences or high humidity.
・Close to rubber products includes rubber adhesives.
The Electrical connection is not affected by tarnishing on a silver surface due to the wiping effect of the contact pins.
Storage
Packing state; Packed in original packing or equivalent container
Temperature -10 to +60
ç
Humidity 85% Max
(It is recommended that the product be stored in an area of normal level of temperature and humidity, and free of any
temperature fluctuation)
Please use this products within 6 months of delivery.
(After 6 month, please check the solderbility before use)
“Storage” means long-term storage of the unused products in sealed packaging, prior to assembly to PCB.
21
HR10 Series●High performance miniature circular connectors
May.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.
