NTE65101 Integrated Circuit 256 x 4-Bit Static Random Access Memory (SRAM) Description: The NTE65101 is a CMOS 1024-bit device organized in 256 words by 4 bits in a 22-Lead DIP type package. This device offers ultra low power and fully static operation with a single 5V supply. Separate data inputs and data outputs permit maximum flexibility in bus-oriented systems. Data retention at a power supply as low as 2V over temperature readily allows design into applications using battery backup for nonvolatility. The NTE65101 is fully static and does not require clocking in standby mode. Features: D Organized as 256 Bytes of 4-Bits D Static Operation D Low Standby Power D Three-State Output D Single 5V Power Supply D Data Retention to 2V D TTL Compatible D Maximum Access Time: 450ns Absolute Maximum Ratings: (Voltages referenced to VSS Pin8) Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to +7V Input Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to VCC +0.3V Operating Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 to +85C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +150C Note 1. This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. DC Electrical Characteristics: (VCC = 5V 5%, TA = 0 to +70C unless otherwise specified) Parameter Symbol Test Conditions Typ Max Unit - 5.0 - nA Input Current Iin Input High Voltage VIH 2.2 - VCC V Input Low Voltage VIL -0.3 - 0.65 V Output High Voltage VOH IOH = -1mA 2.4 - - V Output Low Voltage VOL IOL = 2mA - - 0.4 V Output Leakage Current ILO CE1 = 2.2V, VOL = 0V to VCC, Note 3 - - 1.0 A Operating Current ICC1 Vin = VCC, except CE1 0.65V, Outputs open - 9.0 22 mA ICC2 Vin = 2.2V, except CE1 0.65V, Outputs open - 13 27 mA ICCL CE2 0.2V, Note 3, Note 4 - - 10 A Min Typ Max Unit Standby Current Note 3 Min Note 2. Typical values are TA = +25C and nominal voltage. Note 3. Current through all inputs and outputs included in ICCL measurement. Note 4. Low current state is for CE2 = 0 only. Capacitance: Parameter Symbol Test Conditions Input Capacitance Cin Vin = 0V - 4.0 8.0 pF Output Capacitance Cout Vout = 0V - 8.0 12.0 pF Min Typ Max Unit 2.0 - - V - 0.14 10 A 0 - - ns tRC - - ns Note 2. Typical values are TA = +25C and nominal voltage. Low VCC Retention Characteristics: (TA = 0 to +70C unless otherwise specified) Parameter Symbol VCC for Data Retention VDR Data Retention Current ICCDR1 Chip Deselect to Data Retention Time Operation Recovery Time Test Conditions CE2 0.2V, VDR = 2V tCDR tR Note 5 Note 2. Typical values are TA = +25C and nominal voltage. Note 5. tRC = Read Cycle Time. AC Operating Conditions and Characteristics: (Full operating voltage and temperature unless otherwise specified) AC Test Conditions: Condition Input Pulse Levels Input Rise and Fall Times Output Load - Timing Measurement Reference Level Value +0.65V to 2.2V 20ns 1 TTL Gate and CL = 100pF 1.5V AC Operating Conditions and Characteristics (Cont'd): (Full operating voltage and temperature unless otherwise specified) Read Cycle: Parameter Symbol Min Read Cycle Time Access Time Max Unit tRC 450 - ns tA - 450 ns Max Unit Read Cycle (Cont'd): Parameter Symbol Min Address Setup Time tAS 20 - ns Address Hold Time tAH 0 - ns Chip Enable (CE1) to Output tCO1 - 400 ns Chip Enable (CE2) to Output tCO2 - 500 ns Output Disable to Output tOD - 250 ns Data Output to High Z State tDF 0 130 ns Previous Read Data Valid with Respect to Address Change tOH1 0 - ns Previous Read Data Valid with Respect to Chip Enable tOH2 0 - ns Max Unit Write Cycle: Parameter Symbol Min Write Cycle tWC 450 - ns Write Delay tAW 130 - ns Chip Enable (CE1) to Write tCW1 350 - ns Chip Enable (CE2) to Write tCW2 350 - ns Data Setup tDW 250 - ns Data Hold tDH 50 - ns Write Pulse tWP 250 - ns Write Recovery tWR 50 - ns Output Disable Setup tDS 130 - ns Truth Table: CE1 CE2 OD R/W Din Output Mode H X X X X High Z Not Selected X L X X X High Z Not Selected X X H H X High Z Output Disable L H H L X High Z Write L H L L X Din Write L H L H X Dout Read Pin Connection Diagram A3 A2 A1 A0 A5 A6 A7 1 2 3 4 5 6 7 22 21 20 19 18 17 16 VCC A4 R/W CE 1 OD CD 2 DO 4 GND DI 1 DO 1 DI 2 8 9 10 11 15 14 13 12 DI 4 DO 3 DI 3 DO 2 22 12 .410 (11.41) 1 11 1.300 (33.0) .400 (10.16) .216 (5.5) .100 (2.54) 1.000 (25.4) .110 (2.79)