2004-0911/1000-542 - WAGO - Datasheet.Live

<________ 66,5 mm /2.61 in ________> <_______________ 87,5 mm /3.45 in _______________>

<___33 mm /

__>

1.29 in

<__33 mm /

__>

1.29 in

<___ 38 mm/1.49 in ___>

< _ _ >

VOLUME 1

➊ can be connected: 0.25 mm2 — 4 mm2 "s+f-st";

can be pushed in directly: 0.75 mm2 — 4 mm2 "s" and

0,75 mm2 – 2,5 mm2 "insulated ferrule,

12 mm/0.472 in"

Accessories Series 2002 Appropriate marker systems: WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Vol. 1, Sec. 14)

Article-specific accessories

4-conductor fuse terminal blocks

gray 2002-1881

➋ - Individual arrangement: 10 A

- Block arrangement: 5 A

Please note touchproof protection from 42 V

End and intermediate plate, 1 mm/0.039 in thick

orange 2002-1892 100 (4 x 25)

gray 2002-1891 100 (4 x 25)

Protective warning marker, with high voltage symbol, black,

for 5 terminal blocks

yellow 2002-115 100 (4 x 25)

Staggered jumpers, light gray, insulated, IN 25 A

2-way 2002-472 100 (4 x 25)

3-way 2002-473 100 (4 x 25)

4-way 2002-474 100 (4 x 25)

5-way 2002-475 50 (2 x 25)

: :

12-way 2002-482 50 (2 x 25)

Test plug adapter, for test plug Ø 4 mm/0.157 in

2009-174 100 (4 x 25)

Testing tap, for max. 2.5 mm2/AWG 14

2009-182 100 (4 x 25)

Two-way marking adapter,

pivotable

2002-121 50 (2 x 25)

Test plug, with cable 500mm/1’7.7’’, Ø 2 mm/0.079 in

red 210-136 50 (5 x 10)

The rated currents of the fuse cartridges are

defined differently in international standards.

Due to the different current rating definitions,

the recommended current-carrying permanent

capacity of the fuses is max. 80% of their rated

current according to DIN 72581 part 3 (for an

ambient operating temperature of 23°C).

Selecting the correct fuse cartrigde is important

for product safety within applications as well as

the service life/operational reliability of the fuse

cartrigdes. Fuse cartrigdes can operate perfectly

as protection (break-off point) if they are properly

selected and are used in accordance with

the manufacturers specifications.

In general it is necessary to test fuse cartridges

under normal conditions and operational failures

within your application.

With regard to the product safety, it is in

general necessary to test the fuse in the

appliance under normal conditions and

operational failures.

End and intermediate plate, 1 mm/0.039 in thick

orange 2002-1692 100 (4 x 25)

gray 2002-1691 100 (4 x 25)

Insulation stop, 5 pcs/strip 200 strips

light gray 2002-171 0.25-0.5 mm2

dark gray 2002-172 0.75-1 mm2

Push-in type jumper bars, light gray, insulated, IN 25 A

2-way 2002-402 200 (8 x 25)

3-way 2002-403 200 (8 x 25)

4-way 2002-404 200 (8 x 25)

5-way 2002-405 100 (4 x 25)

: :

10-way 2002-410 100 (4 x 25)

Push-in type jumper bars, light gray, insulated, IN 25 A

1 - 3 2002-433 200 (8 x 25)

1 - 4 2002-434 200 (8 x 25)

1 - 5 2002-435 100 (4 x 25)

: :

1 - 10 2002-440 100 (4 x 25)

Modular TOPJOB®S connector,

for jumper contact slot

1 pole 2002-511 100 (4 x 25)

Spacer, modular 2002-549 100 (4 x 25)

2-conductor fuse terminal blocks

gray 2002-1681

➋ - Individual arrangement: 10 A

- Block arrangement: 5 A

Please note touchproof protection from 42 V

Blade-type fuses acc. to DIN 72581-3f /

ISO 8820-3 (not offered by WAGO)

Item no. Pack. unit Item no. Pack. unit

Fuse Terminal Blocks for Blade-Type Fuses

acc. to DIN 72581-3f, ISO 8820-3, Series 2002

0.25 — 2.5 (4) mm2

➊ AWG 22 — 12

400 V/6 kV/3

IN 10 A ➋

Terminal block width 5.2 mm / 0.205 in

L 10 — 12 mm / 0.43 in

0.25 — 2.5 (4) mm2

➊ AWG 22 — 12

400 V/6 kV/3

IN 10 A ➋

Terminal block width 5.2 mm / 0.205 in

L 10 — 12 mm / 0.43 in

<_____ 57,2mm /2.26in _____>

<_______ 66,5mm /2.62 in _______>

<______ 57,2mm /2.26in ______>

<_______ 66,5mm /2.62in _______>

VOLUME 1

Article-specific accessories

Description

Fuse disconnect terminal block

with pivotable fuse holder,

for DIN 35 rail,

for miniature metric fuses 5 x 20 mm

5 x 20 mm

2-conductor fuse terminal block with end plate,

without blown fuse indication

gray 2002-1611 50

2-conductor fuse terminal blocks with end plate,

with blown fuse indication by LED

gray 12 — 30 V ≃ ➌ 2002-1611/1000-541

gray 30 — 65 V ≃ ➌ 2002-1611/1000-542

gray 110 — 250 V ≃ 2002-1611/1000-836

Fuse Disconnect Terminal Blocks with Pivotable Fuse Holder,

2.5 (4) mm2/AWG 12, for Miniature Metric Fuses 5 x 20 mm, Series 2002

➊

800 V = rated voltage

8 kV = rated surge voltage

3 = pollution degree

(see also Full Line Catalog W4, Volume 1, Section 15)

➋

Nominal voltage and current are given

by the LED or fuse

➌

Leakage current in case of blown fuse:

LED 6 mA

0.25 — 2.5 (4) mm2

AWG 22 — 12

250 V/6 kV/3 ➊

6.3 A ➋

Terminal block width 6.2 mm / 0.244 in

L 10 — 12 mm / 0.43 in

0.25 — 2.5 (4) mm2

AWG 22 — 12

250 V/6 kV/3 ➊

6.3 A ➋

Terminal block width 6.2 mm / 0.244 in

L 10 — 12 mm / 0.43 in

Item no. Pack. unit Item no. Pack. unit

Accessories

Appropriate marker systems: WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Volume 1, Section 14)

End plate for fuse terminal blocks, 2 mm/0.079 in thick

gray 2002-991 100 (4x25)

orange 2002-992 100 (4x25)

End plate for fuse terminal blocks, 2 mm/0.079 in thick

gray 2002-991 100 (4x25)

orange 2002-992 100 (4x25)

Insulation stop, 5 pcs/strip 200 strips

light gray 2002-171 0.25-0.5 mm2

dark gray 2002-172 0.75-1 mm2

must be singularized

Protective warning marker, with high voltage symbol, black,

for 5 terminal blocks

yellow 2002-115 100 (4 x 25)

must be singularized

Push-in type jumper bars, light gray, insulated, IN 25 A

2-way 2004-402 200 (8 x 25)

3-way 2004-403 200 (8 x 25)

4-way 2004-404 200 (8 x 25)

5-way 2004-405 100 (4 x 25)

: :

10-way 2004-410 100 (4 x 25)

Push-in type jumper bars, light gray, insulated, IN 25 A

1 - 3 2004-433 200 (8 x 25)

1 - 4 2004-434 200 (8 x 25)

1 - 5 2004-435 100 (4 x 25)

: :

1 - 10 2004-440 100 (4 x 25)

Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø

red 210-136 50 (5 x 10)

Insulation stop, 5 pcs/strip 200 strips

light gray 2002-171 0.25-0.5 mm2

dark gray 2002-172 0.75-1 mm2

must be singularized

Protective warning marker, with high voltage symbol, black,

for 5 terminal blocks

yellow 2002-115 100 (4 x 25)

must be singularized

Push-in type jumper bars, light gray, insulated, IN 25 A

2-way 2004-402 200 (8 x 25)

3-way 2004-403 200 (8 x 25)

4-way 2004-404 200 (8 x 25)

5-way 2004-405 100 (4 x 25)

: :

10-way 2004-410 100 (4 x 25)

Push-in type jumper bars, light gray, insulated, IN 25 A

1 - 3 2004-433 200 (8 x 25)

1 - 4 2004-434 200 (8 x 25)

1 - 5 2004-435 100 (4 x 25)

: :

1 - 10 2004-440 100 (4 x 25)

Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø

red 210-136 50 (5 x 10)

<______ 57,2mm /2.26in ______>

<_____________ 87,5mm /3.45in _____________>

<______ 57,2mm /2.26in ______>

<_____________ 87,5mm /3.45in _____________>

VOLUME 1

Fuse terminal blocks with a width of 6.2 mm/0.244 in

can be assembled adjacent to each other.

At the end of an assembly, if there is no adjacent fuse

or disconnect terminal block, an end plate for fuse

terminal blocks must be used.

When selecting miniature metric fuses, the maximum

power loss listed below should not be exceeded. The

power loss is determined according to IEC or EN

60947-7-3/VDE 0611-6 at 23°C. The temperature

rise of the terminal blocks must be checked according

to their application and mounting. Higher ambient tem-

peratures represent an additional impact on miniature

metric fuses. Therefore, in such applications the rated

current must be reduced if necessary.

More details from the manufacturer.

Appropriate marker systems:

WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Volume 1, Section 14)

0.25 — 2.5 (4) mm2

AWG 22 — 12

250 V/6 kV/3 ➊

6.3 A ➋

Terminal block width 6.2 mm / 0.244 in

L 10 — 12 mm / 0.43 in

0.25 — 2.5 (4) mm2

AWG 22 — 12

250 V/6 kV/3 ➊

6.3 A ➋

Terminal block width 6.2 mm / 0.244 in

L 10 — 12 mm / 0.43 in

4-conductor fuse terminal block with end plate,

without blown fuse indication

gray 2002-1811 50

4-conductor fuse terminal blocks with end plate,

with blown fuse indication by LED

gray 12 — 30 V ≃

➌

2002-1811/1000-541

gray 30 — 65 V ≃

➌

2002-1811/1000-542

gray 110 — 250 V ≃

2002-1811/1000-836

Item no. Pack. unit Item no. Pack. unit

End plate for fuse terminal blocks, 2 mm/0.079 in thick

gray 2002-991 100 (4x25)

orange 2002-992 100 (4x25)

End plate for fuse terminal blocks, 2 mm/0.079 in thick

gray 2002-991 100 (4x25)

orange 2002-992 100 (4x25)

Protective warning marker and insulation stop

must be singularized.

Due to the 6.2 mm/0.244 in width of the

fuse terminal blocks with pivotable fuse holder,

2004 Series jumpers must be used.

Insulation stop, 5 pcs/strip 200 strips

light gray 2002-171 0.25-0.5 mm2

dark gray 2002-172 0.75-1 mm2

must be singularized

Protective warning marker, with high voltage symbol, black,

for 5 terminal blocks

yellow 2002-115 100 (4 x 25)

must be singularized

Push-in type jumper bars, light gray, insulated, IN 25 A

2-way 2004-402 200 (8 x 25)

3-way 2004-403 200 (8 x 25)

4-way 2004-404 200 (8 x 25)

5-way 2004-405 100 (4 x 25)

: :

10-way 2004-410 100 (4 x 25)

Push-in type jumper bars, light gray, insulated, IN 25 A

1 - 3 2004-433 200 (8 x 25)

1 - 4 2004-434 200 (8 x 25)

1 - 5 2004-435 100 (4 x 25)

: :

1 - 10 2004-440 100 (4 x 25)

Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø

red 210-136 50 (5 x 10)

Insulation stop, 5 pcs/strip 200 strips

light gray 2002-171 0.25-0.5 mm2

dark gray 2002-172 0.75-1 mm2

must be singularized

Protective warning marker, with high voltage symbol, black,

for 5 terminal blocks

yellow 2002-115 100 (4 x 25)

must be singularized

Push-in type jumper bars, light gray, insulated, IN 25 A

2-way 2004-402 200 (8 x 25)

3-way 2004-403 200 (8 x 25)

4-way 2004-404 200 (8 x 25)

5-way 2004-405 100 (4 x 25)

: :

10-way 2004-410 100 (4 x 25)

Push-in type jumper bars, light gray, insulated, IN 25 A

1 - 3 2004-433 200 (8 x 25)

1 - 4 2004-434 200 (8 x 25)

1 - 5 2004-435 100 (4 x 25)

: :

1 - 10 2004-440 100 (4 x 25)

Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø

red 210-136 50 (5 x 10)

Miniature metric fuses 5 x 20

Series

Item No.

Overload and

short circuit protection Short circuit

protection only

2002-1611

2002-1811

Individual

arrangement Group

arrangement

Individual

arrangement Group

arrangement

Fuse terminal blocks

1.6 W 1.6 W 2.5 W 2.5 W

2002-1811/....-....

2002-1611/....-.... 1.6 W 1.6 W 2.5 W 2.5 W

Application notes

<______ 71 mm /2.79 in ➌ ______>

<____________________ ➊ ➋ ____________________>

VOLUME 1

Leakage current in

case of blown fuse

LED 5 — 20 mA,

Neon lamp <0.4 mA

The use of pluggable fuse holders with rail mounted

terminal blocks for protection of control circuits

offers many advantages to the user since

the function and the wiring are accomplished by

two separate parts:

● no additional cost for assembly and wiring

●

no risk of accidental contact with live parts

during disconnection of fuse plug

●

in case of exchanging a defective fuse the fuse

plug is completely separated from the carrier

terminal block

●

therefore safe exchange of the fuse away from

current carrying parts

●

the fuse plug can be taken away by the

serviceman avoiding unintentional reclosing of

the circuit by another person

●

quick exchange of a fuse by using a prepared

“stand-by plug.”

Further advantages:

●

optional LED indicates blown fuse

●

marking facility on the fuse plug for clear coordination

to the correct carrier terminal block

(WSB-Quick Marking System 4 mm/0.157 in)

●

two touchproof test slots

●

high density with only 6,1 mm/0.24 in width of

terminal block/fuse plug

●

instead of a fuse, a shorting link may be used

as a disconnect plug.

When corresponding Neutral-circuit is adjacent to

a fuse plug, a 5.2 mm/0.205 in wide space saving

terminal block may be used, as a 6.1 mm/0.24 in

fuse plug may overlap the terminal block.

See diagram below.

Description

Open side of terminal block

Terminal block width 5.2 mm/0.205 in

gray 2002-1661 50

1 mm/0.039 thick

orange 2002-1692 100 (4 x 25)

gray 2002-1691 100 (4 x 25)

Terminal block width 6 mm/0.236 in

gray 2002-1861 50

1 mm/0.039 thick

orange 2002-1892 100 (4 x 25)

gray 2002-1891 100 (4 x 25)

281-503 250

(10 x 25)

2 mm/0.079 thick

orange 2002-0991 100 (4 x 25)

gray 2002-0992 100 (4 x 25)

2-conductor carrier terminal block ➊,

0.25 — 2.5 (4) mm2/AWG 22 —12

Stripped length 9 —10 mm/0.37 in

End and intermediate plate,

for 2-cond. carrier term. block

Item No. 2002-1661

4-conductor carrier terminal block ➋,

0.25 — 2.5 (4) mm2/AWG 22 —12

Stripped length 10

—12 mm/0.43 in

End and intermediate plate,

for 4-cond. carrier term. block

Item No. 2002-1861

Shorting link, 5 x 20 mm,

6.3 A, if the fuse plug is used as

disconnect plug

End plate for fuse plug

Fuse plug,

for miniature metric fuses

5 x 20 mm

Fuse plug, same as above,

with additional indicator lamp,

LED, AC/DC 12 — 30 V,

LED, AC/DC 30 — 65 V,

can be used in both switching

directions

AC/DC 120 V — 230 V

6.1 mm/0.24 in width with pull-tab

2004-0911 50

6.1 mm/0.24 in width with pull-tab

2004-0911/1000-0541 5 0

2004-0911/1000-0542 5 0

6.1 mm/0.24 in width with pull-tab

2004-0911/1000-0836 5 0

Terminal blocks and accessories Appropriate marker systems: Terminal block WMB/Marker Strips

Fuse Plugs, Series 2004

and Carrier Terminal Blocks, Series 2002

250 V max.*

6.3 max. * Electrical ratings are given by the fuse or nomi-

nal voltage of the indicator lamp respectively.

Item no. Pack. unit

Miniature metric fuses 5 x 20

Series

Item No.

Overload and

short circuit protection Short circuit

protection only

2004-0911

2004-0911/....-....

Individual

arrangement Group

arrangement

Individual

arrangement Group

arrangement

Fuse terminal blocks

1.6 W 1.6 W 2.5 W 2.5 W

➊ 66.5 mm/2.62 in (2-conductor)

➋ 87.5 mm/3.45 in (4-conductor)

➌ with inserted fuse plug Open side of terminal block left