NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 1 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED 1.0 OBJECTIVE This specification defines the performance, test, quality and reliability requirements of the PwrBlade Connector System. 2.0 SCOPE This specification is applicable to the termination characteristics of separable right angle and vertical headers when mated to the right angle and vertical receptacles. 3.0 GENERAL If there is conflict between the product drawings and specifications, the drawing takes precedence. This document is composed of the following sections: Paragraph 1.0 2.0 3.0 4.0 5.0 5.1 5.2 5.3 5.4 5.5 6.0 7.0 8.0 9.0 9.1 9.2 9.3 9.4 9.5 9.6 10.0 Table 2 Title OBJECTIVE SCOPE GENERAL APPLICABLE DOCUMENTS REQUIREMENTS Qualification Material Finish Design and construction Workmanship ELECTRICAL CHARACTERISTICS MECHANICAL CHARACTERISTICS ENVIRONMENTAL CONDITIONS QUALITY ASSURANCE PROVISIONS Equipment Calibration Inspection Conditions Sample Quality and Description Acceptance Qualification Testing Re-qualification Testing Reference Documents Qualification Testing Matrix Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 2 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED 4.0 APPLICABLE DOCUMENTS 4.1 Specifications 4.1.1 4.2 Federal Specifications 4.2.1 4.3 4.4 MIL-STD-1344A: Test Methods for Electrical Connectors Other Standards and Specifications 4.3.1 UL 94 V-0: Flammability 4.3.2 EIA 364: Test Procedures for Electrical Connectors, Sockets and Coaxial Contacts FCI Specifications: 4.4.1 4.4.2 4.4.3 4.4.4 5.0 Applicable FCI power blade product drawings BUS-03-601:Current Rating/30BUS-03-601: Current Rating/30oC Temperature Rise BUS-03-404: Normal Force Measurement BUS-12-090: HPC Product Specification BUS-12-111: HPC Solderless (Press fit) Right Angle Receptacle REQUIREMENTS 5.1 Qualification Connectors furnished under this specification shall be capable of meeting the qualification test requirements specified herein. 5.2 Material The material for each component shall be as specified herein or equivalent. Power Contacts - High Performance Copper Alloy Signal Header Contacts - Copper Alloy Signal Receptacle Contacts - Copper Alloy Receptacle and Plug Housings - Glass Filled HTN (High Temperature Nylon) Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 3 of 13 AUTHORIZED BY AA DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED 5.3 Finish Refer to plating specification 10064183. 5.4 Design and Construction Connectors shall be of the design, construction and physical dimensions specified on the applicable product drawings. 5.4.1 See drawing numbers 51700, 51720, 51740, 51760 and 51866 for test connector configurations. 5.5 Workmanship includes freedom from blistering, cracks, discoloration, etc. ELECTRICAL CHARACTERISTICS 6.1 Signal tested at Low Level (LLCR) - The low level contact resistance shall not exceed 20 milliohm after environmental exposure when measured in accordance with EIA 364 TP 06. The following details shall apply: a. b. Test Voltage - 20 millivolts DC max open circuit. Test Current - Not to exceed 100 milliamps. 6.2 Power tested at Specified Current - The contact resistance at a specified current shall not exceed 0.7 milliohm end of life when measured in accordance with EIA 364 TP32. Test Current 30 amperes DC 6.3 Insulation Resistance - the insulation resistance of mated connectors shall not be less than 10,000 megohms for power contacts, and 500 megohms for signal initially and after environmental exposure when measured in accordance with EIA 364 TP21 a. b. c. 6.4 Test Voltage 500 volts DC Electrification time - 2 minutes Points of Measurement - Between adjacent Contacts Dielectric Withstanding Voltage - There shall be no evidence of arc-over, insulation breakdown, or excessive leakage current (>1 Milliampere ) when mated connectors are tested in accordance with EIA 364 TP 20. The following details apply: a. b. c. Test Voltage - 2500 volts DC (power), 1000 volts DC (signal) Test Duration - 60 seconds. Test Condition - (760 Torr - sea level). Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 4 of 13 AA AUTHORIZED BY DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED 6.5 Current Rating - Refer to table 1, the temperature rise above ambient shall not exceed 30 at any point in the system at specified amperes (Table 1) when mated connectors are tested in accordance with EIA-364-70, method 1. The following detail shall apply: a) Ambient Conditions - Still air at 25 b) Stabilize at a single current level until 3 readings at 5 minutes intervals are within 1. c) Test with single energized contact and with all adjacent power contacts energized. Table 1: Rated current table (amperes) Types Power Contact Pitch Single 2 adjacent 4 adjacent 8 adjacent 12 adjacent (mm) Contact Contacts* Contacts Contacts Contacts 6.35 48 50* 36 31 30 * 2 adjacent contacts test by wire, the wire size is 6AWG. Types Signal Contact 7.0 Pitch Single (mm) Contact 2.54 3 Multiple contact 1 MECHANICAL CHARACTERISTICS 7.1 Mating/Unmating Force - The force to mate a receptacle connector and compatible header shall not exceed 6.94N [25 ounce] per power contact and 0.97N [3.5 ounce] per signal contact. The unmating force shall not be less than 2.23N [8 ounce] per power contact and 0.18N [0.64 ounce] per signal contact. The following details shall apply: Table 2: Mating/Unmating Force Force spec. Power contact Signal contact Mating force Maximum 6.94N [25 ounce] 0.97N [3.5 ounce] Unmating force Minimum 2.23N [8 ounce] 0.18N [0.64 ounce] a. b. c. d. 7.2 Cross Head Speed - 25.4mm [1 inch] per minute Lubrication - None Utilize free floating fixtures Reference EIA 364-13 Normal Force - The contact normal force shall not be less than 350 grams per beam for the power contacts and 50 grams (nor greater than 120 grams) per beam for the signal contacts when tested in accordance with FCI Test Specification BUS-03-404. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 5 of 13 AA AUTHORIZED BY DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED 7.3 Contact Retention - Individual power and signal contacts shall withstand an axial retention load of 13.4N [3 pound]. Individual signal receptacle contacts will withstand an axial load of 26.7N [6 pound] minimum to seat further into housing. a. Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity. b. Test 30 contacts c. As per MIL-STD-1344A, Method 2007.1. 7.4 Individual Pin Insertion/Retention Force - The force required to insert an individual compliant pin into a plated through hole in a printed circuit board at a rate of 5.08mm [0.2 inch] per minute shall not exceed 26.6N [6 pound] for signal receptacle contacts, 93.4N [21 pound] for signal header pins and 111.2N [25 pound] per tail for power contacts . The retention force in the axial direction opposite that of insertion shall not be less than 6.7N [1.5 pound] for signal receptacle contacts, 13.4N [3 pound] for signal header pins and 22.3N [5 pound] per tail for power contacts. Table 3: Individual Pin Insertion/Retention Force table Force spec. Pwr contact (per tail) Signal contact Rec Signal contact Hdr Signal contact Insertion force Maximum 111.2N [25lbs] 26.6N [6lbs] 93.4N [21lbs] Retention force Minimum 22.3N [5lbs] 6.7N [1.5lbs] 13.4N [3lbs] 7.5 PCB Hole Deformation Radius Power Contacts - cross-section parallel to board surface. Photograph and measure the hole deformation (deformation on board material) radius at a point 0.254mm [0.010"] from the surface, and the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole deformation radius shall be no greater than0.0381mm [0.0015"] when measured from the drilled hole. The absolute maximum deformation radius shall not exceed 0.0508mm [0.002"]. Signal Contacts Signal Receptacle Contacts - Reference FCI BUS-12-111 - HPC Solderless (Press Fit) Right Angle Receptacles Signal Header Contacts - Same as the requirement for Power Contacts above 7.6 PCB Hole Wall Damage - Cross-section perpendicular to the board surface, and through the compliant section wear track. Photograph and measure the copper thickness remaining between the compliant section and the printed wiring board laminate. Include 10 holes. The minimum average (of 10 holes) copper thickness remaining between the compliant pin and the printed wiring board laminate shall not be less than 0.00762mm [0.0003"]. In addition there shall be no copper cracks, separations between conductive interfaces, or laminate-to-copper separations. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 6 of 13 AUTHORIZED BY AA DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED 7.7 Board Lock Retention to Housing- Individual board locks shall withstand an axial load of 13.4N [3 pound] minimum. * Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity. * Test 30 board locks ENVIRONMENTAL CONDITIONS After exposure to the following environmental conditions in accordance with the specified test procedure and / or details, the product shall show no physical damage and shall meet the applicable electrical and mechanical requirements of paragraphs 6.0 and 7.0 as detailed in Table 1 test sequences. Unless otherwise specified, assemblies shall be mated during exposure. 8.1 8.2 Thermal Shock - EIA 364 TP 32 a. Test condition - 36 cycles b. c. d. Temperature Range - -55 to +125 o C Time at Each Temperature - To refer to EIA 364 TP 32 based on product mass Transfer Time - 5 minutes, maximum Humidity, Steady State - EIA 364 TP 31, Method II a. b. c. 8.3 Test Duration - 96 hours High Temperature Life, EIA 364 TP 17 a. b. c. 8.4 Relative Humidity - 95% Temperature - +40 o C Test Duration - 21 Days Temperature - +125 o C Pre-condition - Perform number of durability cycles specified for product Environmental Sequence: Phase I - Thermal Shock, EIA 364-32 a. Test Duration - 36 cycles b. Temperature Range - Between -55 and +125 o C c. Time at Each Temperature - To refer to EIA 364-32 based on product mass d. Transfer Time - 5 minutes, maximum Phase II - Humidity, EIA 364-31, Method II a. Test Duration - 10 days b. Relative Humidity - 95% Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 7 of 13 AA AUTHORIZED BY DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED c. Temperature - +40 o C Phase III - High Temperature Life, EIA 364-17 a. Test Duration - 21days b. Temperature - +125 o C c. 8.5 Industrial Mixed Flowing Gas (IMFG) - EIA 364-65 a. b. c. d. 8.6 e. f. Number of Cycles - 200 Cycling rate - 127mm [5 inch] per minute Solderability - ANSI-J-002, Test Condition A a. b. 8.10 Condition A (50G, 11 millisecond half sine wave) Shocks - 3 shocks in both directions along each of three orthogonal axes (18 total) Mounting - rigidly mount assemblies No discontinuities of greater than 10 nano-seconds Durability - Standard laboratory procedure as applicable to the specific product a. b. 8.9 Condition - III Vibration Amplitude - 1.524mm [0.06"] DA or 15G Frequency Range - 10 to 2000 to 10 Hz Sweep Time and Duration - 20 minutes per cycle, 4 hours along each of three orthogonal axes (12 hours total) Mounting - rigidly mount assemblies No Discontinuities of greater than 10 nano-seconds Mechanical Shock - EIA 364-27 a. b. c. d. 8.8 Class - IIA Duration - 20 days Mated Test contact resistance after 10 and 20 days Vibration Sinusoidal - EIA 364 TP 28 a. b. c. d. 8.7 Pre-condition - Perform number of durability cycles specified for product Steam aging - 4 hours Pcb termination area was evaluated and meets the requirements of ANSI-J-002. Resistance to Solder Heat - EIA 364-56 a. Test Condition - E b. There shall be no evidence of physical or mechanical damage. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 8 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED 8.11 9.0 Operating temperature - -55 o C to 125 o C QUALITY ASSURANCE PROVISIONS 9.1 Equipment Calibration All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with ISO 9000 9.2 Inspection conditions Unless otherwise specified, all inspections shall be performed under the following conditions: a. b. c. Temperature: 25 +/- 5o C Relative humidity: 30 to 60% Barometric Pressure: Local ambient Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE REVISION PwrBlade (R) Product Specification 9 of 13 AA AUTHORIZED BY DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED 9.3 Sample Quality and Description R/A Header P/N 51720, Vertical Receptacle P/N 51740 and R/A Receptacle P/N 51760 P/N For lead free test, use 517*0 - ********LF Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 51720-11008410AA_ _ Ass'y 6 3 O 6 6 3 3 O 6 2 3 3 0 0 51740-11008410AA_ _ Ass'y 0 3 M 0 0 0 0 M 0 0 0 0 0 0 51740-11008410CC_ _ Ass'y 3 0 I 3 3 0 3 I 3 0 0 0 9 0 51760-11008410AA_ _ Ass'y 3 0 T 3 3 3 0 T 3 2 3 3 0 12 SK-44146-002 PCB 0 0 T 0 0 0 0 T 0 0 0 0 0 0 SK-44147-002 PCB 0 0 E 0 0 0 0 E 0 0 0 0 9 0 SK-44148-002 PCB 0 0 D 0 0 0 0 D 0 0 0 0 0 0 SK-44146-012 PCB 6 3 6 0 3 3 6 0 0 0 0 0 SK-44147-012 PCB 3 3 3 0 0 3 3 0 0 0 9 0 SK-44148-012 PCB 3 0 3 0 3 0 3 0 0 0 0 0 Vertical Header P/N 51700, R/A Receptacle Press Fit P/N 51866 and Vertical Receptacle P/N 51740 (mated to 51700 for qualification testing) P/N For lead free test, use 517*0 ********LF 51546-001021_ _ Type 1 2 contact 3 3 4 5 O O M M 51700-11008410AA_ _ Ass'y 51700-11008410CC_ _ Ass'y SK-44145-002 (2 oz) PCB SK-44145-012 (5 oz) PCB 3 3 E 3 E 51866-002_ _ Ass'y 3 3 D 3 D 51740-1108410AA_ _ Ass'y SK-44148-002 (2 oz) PCB SK-44148-012 (5 oz) PCB SK-44147-002 (2 oz) PCB SK-44147-012 (5 oz) PCB 3 I 3 T 6 7 8 9 11 O 3 I M 6 T 3 3 6 12 O 4 I M 4 I T 2 2 T E 2 2 E D 4 6 13 14 12 3 1 D 4 2 3 3 2 2 3 6 2 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 TITLE PRODUCT SPECIFICATION PAGE PwrBlade (R) Product Specification REVISION 10 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED 9.4 9.5 Acceptance 9.4.1 Electrical and Mechanical requirements shall be as indicated in Paragraphs 6.0 and 7.0 using test data and appropriate statistical techniques. 9.4.2 Failures attributed to equipment, test setup or operator error shall not disqualify the product. Qualification Testing Qualification testing shall be performed on sample units predicted with equipment and procedures normally used in production. Test sequence is as shown in Table 1. 9.6 Re-qualification Testing If any of the following conditions occur, the responsible product engineer shall initiate re-qualification testing consisting of the applicable parts of the test matrix, Table 1. a. A significant design change is made to the existing product that impacts the product form, fit or function. Examples of significant changes shall include, but not be limited to, changes in the plating material composition or thickness, contact force or contact surface geometry, insulator design, contact base material or contact lubrication requirements. b. A significant event occurs during production or end use requiring corrective action to be taken relative to the product design or manufacturing process. c. A significant change is made to the manufacturing process that impacts the product form, fit or function. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 11 of 13 AA AUTHORIZED BY DATE MT Ruan 29 Jul 16 CLASSIFICATION UNRESTRICTED Test Sequence Table 3 Test Examination of Product PAR 5.5 Contact Resistance Low Level 6.1 Contact Resistance At specified current 6.2 Insulation Resistance 6.3 Dielectric Withstanding Voltage Current Rating Mating/Unmating Force 6.4 Normal Force Contact Insertion/ Retention Individual Pin Insertion (new pin for each insertion) 7.2 7.3 7.4 Individual Pin Retention 7.4 PCB Hole Deformation Radius PCB Hole Wall Damage Board Lock Retention Thermal Shock Humidity, Steady State Hi Temperature Life Environmental Sequence Phase I Phase II Phase III Ind. Mixed Flowing Gas Vibration Mechanical Shock Durability Solderability Res. To Soldering Heat 7.5 7.6 7.7 8.1 8.2 8.3 8.4 6.5 7.1 1 2 3 4 5 6 1 20 3 6 9 14 17 1 12 3 6 10 O M I T T E D 1 8 2 6 1 8 1 3 4 7 10 15 18 4 7 11 3 7 Test Group 7 8 9 Test Sequence 1 O 1 8 M 3 2 I 6 T T E D 10 11 12 13 14 1 3 1 1 3 1 13 3 6 9 1 3 3 7 2 6 3 7 2 2 11 13 19 2 8 2 2 2 5 8 4 7 10 11 12 2 4 5 5 5 8 16 8.5 8.6 8.7 8.8 8.9 8.10 9 4 5 12 5 4 2 2 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 12 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED REVISION RECORD REV A PAGE ALL B 2,12,14,16, 17 C ALL DESCRIPTION New release EC# V10892 DATE 02/22/01 Update to include R/A Receptacle press fit V11528 05/02/01 V12261 09/24/01 Correct test procedure numbering V12530 11/14/01 Added reference to HPC product specification V20869 05/2/02 Revise test groups and sequences to reflect actual test procedures Update to include vertical header Remove test group 8 D 5&6 E 1, 2, 4, 6, 7, 9 Added/deleted referenced lab reports to make current Added vertical header signal contact press fit values Added vertical header and R/A receptacle press fit test sample table Corrected paragraph numbering in test sequence table; Added Areva log F 2 Add HPC press fit specifications references 3 Add P/N 51866 to paragraph 5.4.1 4 Include min. 6# to seat signal receptacle contacts further into housing. V21237 8/05/02 V21408 8/29/02 DG06-0223 6/02/06 DG06-0400 12/13/06 Revised Section 7.5 to include references to HPC specifications G 7 H 1 3 J 3 Increase durability rating to 200 cycles 4.1.1 Add more typical P/N series: 51939, 51940, 51897, 51921 etc. 5.3 Update the finish for Powerblade all series 9 9.3 Add the test samples P/N for Lead Free parts, in the table" For lead free test, use 517*0 - ********LF" All Change the "FCI" logo &7 Update dwell time for 8.1 and phase 1 in 8.4 5 Update insertion / retention force for signal header pins (7.4) 6 Update hole deformation radius for signal header pins (7.5) K 5 Update to clarify para. 6.5 by a clearer description DG07-0002 1/4/07 L 2 Remove referenced FCI spec. GS-12-005: Split-Lif Compliant and FCI Lab Reports. (4.4.5 & 4.5) DG07-0323 8/08/07 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 NUMBER TYPE GS-12-149 PRODUCT SPECIFICATION TITLE PAGE PwrBlade (R) Product Specification REVISION 13 of 13 AUTHORIZED BY MT Ruan AA DATE 29 Jul 16 CLASSIFICATION UNRESTRICTED M 5&8 Update to clarify the retention force of power pin by a clearer description. (7.4) DG07-0420 10/23/07 DG08-0022 01/21/08 Change operating temperature range. (8.11) N 3 & 8 & 11 Add GXT plating option on contact area. (5.3) Correct operating temperature range. (8.11) Correct the test sequence in test group 1. P 3 Remove Gold Flash plating option on tail area. (5.3) DG08-0187 07/22/08 R 3 Remove GXT plating option on contact area for Signal contact. (5.3) DG08-0226 08/19/08 S 2&3 Modify item 4.1 drawing number & 5.3 add plating spec. 10092675 DG08-0255 10/02/08 T 7 Change operating temperature range. (8.11) DG10-0162 05/04/10 U 2&3 Remove PwrBlade Qualification Summary GS-29149. (4.4.1) DG10-0205 06/02/10 DG-13984-1 03/27/13 Re-describe raw materials of Power and Signal contacts. (5.2) Remove plating specification 10092675. (5.3) Tighten Contact Resistance spec. of Power contacts from 2.0 milliohm max. to 0.7 milliohm max.. V 1, 4, 6,7,10 Add a new table for Individual Pin Insertion/Retention Force.(7.4) Change operation temperature range.(8.11) W ALL X 3,5,6,7 Y 4 ALL AA 4 Correct print error DG-14425-1 04/07/13 Update operating temperature DG-16432-1 03/04/14 DG-23359 02/25/16 DG-24556 07/29/16 Update current rating (6.5) Update logo Update current rating of signal contact (6.5) Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 51624-XX001LF 51721-10002406AALF 51700-11102003AALF 51721-10002406ABLF 51744-10202402A0LF 51742-10202400CCLF 51416-001LF 51704-10202402A0LF 51866-008LF 51415-001LF 51625-XX001LF 5174210302400CCLF 51720-10402002AALF 51740-11102003AALF 51720-10202402AALF 51720-10602804ABLF 5176010602804ABLF 51261-XX001LF 51617-XX002LF 51666-001LF 51667-XX001LF 51700-10104801AALF 5170010106001AALF 51700-10201602CCLF 51700-10202402AALF 51700-10402404AALF 51700-10403204CALF 5170010602406CALF 51701-10002408CCLF 51701-10003208CCLF 51703-10400000CCLF 51704-10206002A0LF 5172010002004AALF 51720-10101201AALF 51720-10101601AALF 51720-10102401AALF 51720-10103201ABLF 5172010106001AALF 51720-10106001ABLF 51720-10201202ABLF 51720-10202403AALF 51720-10202404AALF 5172010203202AALF 51720-10203206AALF 51720-10204802AALF 51720-10208002AALF 51720-10300803AALF 5172010301203AALF 51720-10301603ABLF 51720-10302003AALF 51720-10302403AALF 51720-10302406AALF 5172010312803ABLF 51720-10400804AALF 51720-10401204AALF 51720-10402402AALF 51720-10402404AALF 5172010402404ABLF 51720-10402406AALF 51720-10402406ABLF 51720-10410004AALF 51720-10500805AALF 5172010502405AALF 51720-10602406AALF 51720-10602807ABLF 51720-10701607ABLF 51720-10702407AALF 5172010702807ABLF 51720-10703206AALF 51720-10802408AALF 51720-10803208AALF 51720-11102003AALF 5172110000807AALF 51721-10001608AALF 51721-10002408ABLF 51721-10002410AALF 51721-10002414AALF 5172110004808ABLF 51722-10103600AALF 51722-10302400AALF 51722-10401600AALF 51722-10402400AALF 5172210502400AALF 51722-10600800AALF 51722-10602000AALF 51722-10603600AALF 51722-10702400AALF 5172210802400AALF 51722-10802400ABLF 51722-10901600AALF 51722-11103200AALF 51722-11202000AALF 5172211402400AALF 51722-12002000ABLF 51723-10300000AALF 51723-10400000AALF 51723-10700000AALF 5172310800000AALF 51723-10900000AALF 51723-11600000AALF