DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS Class 2, X7R Product Specification - Jan 14, 2005 V.9 10 V Phycomp Product specification Surface-mount ceramic multilayer capacitors FEATURES Class 2, X7R 10 V QUICK REFERENCE DATA DESCRIPTION * Four standard sizes VALUE * For high frequency applications Rated voltage UR (DC) 10 V * Supplied in tape on reel or in bulk case Capacitance range (E6 series): 33 nF to 4.7 F * NiSn terminations. Tolerance on capacitance after 1000 hours 10% Test voltage (DC) for 1 minute: 2.5 x UR Sectional specifications IEC 60384-10, second edition 1989-04;also based on CECC 32 100 Detailed specification based on CECC 32 101801 Climatic category (IEC 60 068) 55/125/21 APPLICATIONS * Consumer electronics for example - Tuners - Television receivers - Video recorders - All types of cameras. Note 1. Measured at 20 C, 1 V and 1 kHz, using a four-gauge method. DESCRIPTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. terminations electrodes The inner electrodes are connected to the two terminations and finally covered with a layer of plated tin (NiSn). A cross section of the structure is shown in Fig.1. MLB457 ceramic material Fig.1 2005 Jan 14 Rev.9 Construction of a ceramic multilayer capacitor. 2 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V MECHANICAL DATA W T L2 L4 L3 MBB211 L1 For dimensions see Table 1. Fig.2. Component outline. Physical dimensions Table 1 Capacitor dimensions; see Fig.2 L1 CASE SIZE W L2 and L3 . T MIN. MAX. MIN. MAX. L4 MIN. Dimensions in millimetres 0402 1.0 0.05 0.5 0.05 0.45 0.55 0.15 0.30 0.40 0603 1.6 0.10 0.8 0.07 0.73 0.87 0.25 0.65 0.40 0805 2.0 0.10 1.25 0.10 0.50 1.35 0.25 0.75 0.55 1206 3.2 0.20 1.6 0.15 0.50 1.75 0.25 0.75 1.40 Dimensions in inches 0402 0.040 0.002 0.020 0.002 0.018 0.022 0.008 0.012 0.016 0603 0.063 0.004 0.032 0.003 0.029 0.035 0.010 0.026 0.016 0805 0.079 0.004 0.049 0.004 0.020 0.053 0.010 0.030 0.022 1206 0.126 0.008 0.063 0.006 0.020 0.069 0.010 0.030 0.056 2005 Jan 14 Rev.9 3 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V SELECTION CHART FOR 10V C (nF) LAST TWO DIGITS OF 12NC 0402 33 43 0.5 0.05 39 44 47 45 56 46 68 47 82 48 100 49 120 - 150 52 180 53 220 54 270 55 330 56 390 57 470 58 560 59 680 61 820 62 1 000 63 1 200 64 1 500 65 1 800 66 2 200 67 3 300 69 4 700 72 10V 0603 0805 1206 0.8 0.07 0.6 0.10 0.85 0.10 1.25 0.10 0.85 0.10 1.25 0.10 1.15 0.1 1.6 0.15 Note 1. Values in shaded cells indicate thickness class. 2005 Jan 14 Rev.9 4 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V Thickness classification and packing quantities for 10 V THICKNESS CLASSIFICATION (mm) 0.5 0.05 0.6 0.10 0.80 0.07 0.85 0.10 1.15 0.10 1.25 0.10 1.6 0.15 2005 Jan 14 Rev.9 8 mm TAPE WIDTH QUANTITY PER REEL 180 mm; 7" 330 mm; 13" QUANTITY PER BULK CASE PAPER BLISTER PAPER BLISTER 0402 0603 0805 10 000 4 000 4 000 4 000 - - - - - - - 3 000 3 000 2 500 50 000 20 000 15 000 15 000 - - - - - - - 10 000 10 000 8 000 50 000 - - - - - - - - 15 000 - - - - - 10 000 - - - 5 000 - 5 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V ORDERING INFORMATION FOR 10V Components may be ordered by using either a Phycomp's unique 12NC or simple 15-digit clear text code. Ordering code 12NC (preferred) 2 2 X X handbook, full pagewidth X X X X 5 X X X Capacitance value(1) Carrier type 22 blister 38 paper tape 54 bulk Tolerance 6 10% Rated voltage - Termination 24 10 V; NiSn Size 7 0402 6 0603 0 0805 1 1206 CCB409 Packaging(2) 1 reel: 180 mm; 7" 5 reel: 330 mm; 13" 4 bulk case (1) Refer to chapter "Selection chart". (2) Quantity on reel depends on thickness classification, see section "Thickness classification and packing quantities". Clear text code EXAMPLE: 06032R154K6BB0D Size Code 0402 0603 0805 1206 Temp. Char. Capacitance Tol. 2R = X7R 154 = 150 000 K = 10% pF; the third digit signifies the multiplying factor: Vol. 6 = 10 V Termination B = NiSn 4 = x 10 000 5 = x 100 000 2005 Jan 14 Rev.9 6 Packing Marking Series 2 = 180 mm; 7" paper 0 = no marking D = BME 3 = 330 mm; 13" paper B = 180 mm; 7" blister F = 330 mm; 13" blister P = bulk case www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V ELECTRICAL CHARACTERISTICS Class 2 capacitors; X7R dielectric; NiSn terminations Unless otherwise stated all electrical values apply at an ambient temperature of 20 1 C, an atmospheric pressure of 86 to 106 kPa, and a relative humidity of 63 to 67%. DESCRIPTION VALUE Capacitance range (E6 series); note 1 33 nF to 4.7 F Tolerance on capacitance after 1000 hours 10% Tan ; note 1 5% Insulation resistance after 1 minute at UR (DC) Rins x C 500 seconds Maximum capacitance change as a function of temperature 15% Ageing typical 3% per time decade Resistance to soldering heat 260 C; 10 seconds Note 1. Measured at 20 C, 1 V and 1 kHz, using a four-gauge method. 2005 Jan 14 Rev.9 7 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V TESTS AND REQUIREMENTS Table 3 Test procedures and requirements IEC 60384-10/ CECC 32 100 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS 4.4 mounting the capacitors may be mounted on printed-circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive no visible damage 4.5 visual inspection and dimension check any applicable method using x10 magnification in accordance with specification 4.6.1 capacitance f = 1 kHz; measuring voltage 1 Vrms at 20 C within specified tolerance 4.6.2 tan f = 1 kHz; measuring voltage in accordance with specification 4.6.3 insulation resistance at UR (DC) for 1 minute in accordance with specification 4.6.4 voltage proof 2.5 x UR for 1 minute; no breakdown or flashover 4.7.1 temperature characteristic between minimum and maximum temperature in accordance with specification 4.8 adhesion a force of 5 N applied for 10 s to the line joining the terminations and in a plane parallel to the substrate no visible damage 4.9 bond strength of plating on end face mounted in accordance with CECC 32 100, paragraph 4.4 no visible damage conditions: bending 1 mm at a rate of 1 mm/s, radius jig. 340 mm C/C: 10% precondition: the terminations shall be well tinned after recovery 1 Vrms at 20 C 4.10 Tb resistance to soldering heat resistance to leaching; jig clamps to the second component in the longitudinal line 2005 Jan 14 Rev.9 120 to 150 C for 1 minute; 260 5 C for 10 0.5 s C/C: 10% 260 5 C for 30 1 s in a static solder bath using visual enlargement of x10, dissolution of the terminations shall not exceed 10% 8 www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V IEC 60384-10/ CECC 32 100 CLAUSE IEC 60068-2 TEST METHOD 4.11 Ta solderability zero hour test, and test after storage (20 to 24 months) in original packing in normal atmosphere; unmounted chips completely immersed for 2 0.5 s in a solder bath at 235 5 C the terminations shall be well tinned 4.12 Na rapid change of temperature preconditioning; 5 cycles in the following sequence: no visible damage after 48 hours recovery: 30 minutes at -55C, change within 30 minutes to +125 C C/C: 15% initialization: preconditioning: UR at 40 C for 1 hour after 48 hours recovery: 4.14 Ca TEST damp heat, steady state PROCEDURE 48 hours after UR at 40 C for 1 hour (for initial value measurement); 500 12 hours at 40 C; 90 to 95% RH; UR applied REQUIREMENTS C/C: 15% tan : 7% Rins: 500 M or RiCR 25 s, whichever is less 4.15 2005 Jan 14 Rev.9 endurance preconditioning: after 48 hours recovery: 2 x UR at 125 C for 1 hour hour (initial value is measured after 48 hours, recovery at room temperature); 1000 hours at 125 C and 2 xUR applied C/C: 20% 9 tan : 7% Rins: 2000 M or RiCR 50 s, whichever is less www.yageo.com Phycomp Product specification Surface-mount ceramic multilayer capacitors Class 2, X7R 10 V REVISION HISTORY Revision Date Change Notification Description Rev.9 2005 Jan 14 - - Capacitance range extended Rev.8 2003 Sep 26 - - Size 1206 L1 dimensions revised. - Size 0402 and 0603 capacitance range expanded, refer to selection chart. Rev.7 2003 Jun 26 - - Rev.6 2003 Mar 25 - - Updated company logo. Rev.5 2002 Jul 15 - - Capacitance range changed from E6 into E12. - Capacitance range expanded to 4.7 F. - Figures 3 through 7 corrected. 2005 Jan 14 Rev.9 10 www.yageo.com * print-friendly version Product Detail Information Product Group Multilayer Capacitor Chips and Arrays Ordering Code CC0402KRX7R6BB473 Ordering Code 223824715645 Unified CTC C0402KRX7R6BB473 Additional Product Code04022R473K6B20D Description General purpose, 0402, X7R, 47nF, ?10%, 10V, 7" paper Status Standard Size Code Capacitance Tolerance Packing Style Dielectric Material (TC) Rated Voltage Capacitance 0402 +-10% Paper Tape & 180mm (7") Reel X7R 10V 47 nF Related Data Sheets, Catalogs and Application Notes: Datasheet - X7R 10 V, Rev.9 [211 kb] Product Selection Guide 2008 (revision 1) [3.65 MB] Yageo Passive Components 2008 [3.26 mb] Material declaration MLCCs type X7R, [85 kb] Environmental declaration Appl. note - DC, AC and Pulse load of Multilayer Ceramic Capacitors [308 kb] MLCC sample kits [177 kb] Appl. manual - MLCC application manual [577 kb] Datasheet - MLCC introduction, Rev.9 [98 kb] Datasheet - MLCC general data of packing, labelling, mounting, tests & requirements; Rev.7 [159 kb] Flowchart - Quality Flowchart, Rev.4 [80kb] Calculation tool - MLCC Spice Data General info - Standard Values in a Decade [8.39 kb] Requirements, Rev.7 [158 kb] For optimal printing of Data sheets print from page 2 of the PDF. Note Clear Text Codes in the data sheets can differ from the Clear Text Codes displayed above. The CTC displayed above is a new code which has been introduced to align product codes in the complete Yageo organisation. You can search products with the CTC displayed in the data sheet by using the competitor part number search function. Documents are in PDF format so to view and print them you will need Adobe Acrobat Reader installed on your computer. This is available free of charge. Copyright (c) 2002-2005 Yageo Corporation Privacy Policy | Access to and use of this web site is subject to the following Terms of use Springsite Technology