DATA SHEE
T
SURFACE-MOUNT CERAMIC
MULTILAYER CAPACITORS
Class 2, X7R
10
V
Product Specification – Jan 14, 2005 V.9
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 2 www.yageo.com
FEATURES
Four standard sizes
For high frequency applications
Supplied in tape on reel or in bulk
case
NiSn terminations.
APPLICATIONS
Consumer electronics for example
Tuners
Television receivers
Video recorders
All types of cameras.
DESCRIPTION
The capacitor consists of a
rectangular block of ceramic
dielectric in which a number of
interleaved metal electrodes are
contained. This structure gives rise
to a high capacitance per unit
volume.
The inner electrodes are connected
to the two terminations and finally
covered with a layer of plated tin
(NiSn). A cross section of the
structure is shown in Fig.1.
QUICK REFERENCE DATA
DESCRIPTION VALUE
Rated voltage UR (DC) 10 V
Capacitance range (E6 series): 33 nF to 4.7 µF
Tolerance on capacitance after 1000 hours ±10%
Test voltage (DC) for 1 minute: 2.5 × UR
Sectional specifications IEC 60384-10, second
edition 1989-04;also based
on CECC 32 100
Detailed specification based on CECC 32 101-
801
Climatic category (IEC 60 068) 55/125/21
Note
1. Measured at 20
°C, 1 V and 1 kHz, using a four-gauge method.
MLB457
terminations
electrodes
ceramic material
Fig.1 Construction of a ceramic multilayer capacitor.
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 3 www.yageo.com
MBB211
T
L4
L1
L2L3
W
MECHANICAL DATA
Fig.2. Component outline.
For dimensions see Table 1.
Physical dimensions
Table 1 Capacitor dimensions; see Fig.2
T L2 and L3 .
CASE SIZE L1 W
MIN. MAX. MIN. MAX.
L4
MIN.
Dimensions in millimetres
0402 1.0
±0.05 0.5
±0.05 0.45 0.55 0.15 0.30 0.40
0603 1.6 ±0.10 0.8 ±0.07 0.73 0.87 0.25 0.65 0.40
0805 2.0
±0.10 1.25
±0.10 0.50 1.35 0.25 0.75 0.55
1206 3.2
±0.20 1.6
±0.15 0.50 1.75 0.25 0.75 1.40
Dimensions in inches
0402 0.040 ±0.002 0.020 ±0.002 0.018 0.022 0.008 0.012 0.016
0603 0.063
±0.004 0.032
±0.003 0.029 0.035 0.010 0.026 0.016
0805 0.079
±0.004 0.049
±0.004 0.020 0.053 0.010 0.030 0.022
1206 0.126 ±0.008 0.063 ±0.006 0.020 0.069 0.010 0.030 0.056
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 4 www.yageo.com
SELECTION CHART FOR 10V
10V
C
(nF)
LAST
TWO DIGITS
OF 12NC 0402 0603 0805 1206
33 43 0.5 ±0.05
39 44
47 45
56 46
68 47
82 48
100 49
120 0.8 ±0.07
150 52
180 53
220 54 0.6 ±0.10
270 55
330 56 0.85 ±0.10
390 57
470 58
560 59 1.25 ±0.10
680 61
820 62
1 000 63 0.85 ±0.10
1 200 64 1.25 ±0.10
1 500 65 1.15 ±0.1
1 800 66
2 200 67
3 300 69 1.6 ±0.15
4 700 72
Note
1. Values in shaded cells indicate thickness class.
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 5 www.yageo.com
Thickness classification and packing quantities for 10 V
8 mm TAPE WIDTH QUANTITY PER REEL
180 mm; 7" 330 mm; 13" QUANTITY PER BULK CASE
THICKNESS
CLASSIFICATION
(mm) PAPER BLISTER PAPER BLISTER 0402 0603 0805
0.5 ±0.05 10 000 50 000 50 000
0.6 ±0.10 4 000 20 000 10 000
0.80 ±0.07 4 000 15 000 15 000
0.85 ±0.10 4 000 15 000
1.15 ±0.10 3000 10 000
1.25 ±0.10 3000 10 000 5000
1.6 ±0.15 2 500 8 000
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 6 www.yageo.com
ORDERING INFORMATION FOR 10V
Components may be ordered by using either a Phycomp’s unique 12NC or simple 15-digit clear text code.
Ordering code 12NC (preferred)
handbook, full pagewidth
2 2 X X X X X X 5 X X X
Carrier type
22
38
54
blister
paper tape
bulk
Rated voltage - Termination
24 10 V; NiSn
Size
7
6
0
1
0402
0603
0805
1206
Capacitance value(1)
Tolerance
6±10%
Packaging(2)
1
5
4
reel: 180 mm; 7"
reel: 330 mm; 13"
bulk case
CCB409
(1) Refer to chapter “Selection chart”.
(2) Quantity on reel depends on thickness classification, see section “Thickness classification and packing quantities”.
Clear text code
EXAMPLE: 06032R154K6BB0D
Size
Code
Temp.
Char. Capacitance Tol. Vol. Termination Packing Marking Series
0402
0603
0805
1206
2R = X7R 154 = 150 000
pF; the third digit
signifies the
multiplying factor:
4 = × 10 000
5 = × 100 000
K = ±10% 6 = 10 V B = NiSn 2 = 180 mm; 7" paper
3 = 330 mm; 13" paper
B = 180 mm; 7" blister
F = 330 mm; 13" blister
P = bulk case
0 = no marking D = BME
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 7 www.yageo.com
ELECTRICAL CHARACTERISTICS
Class 2 capacitors; X7R dielectric; NiSn terminations
Unless otherwise stated all electrical values apply at an ambient temperature of 20 ±1 °C, an atmospheric pressure of
86 to 106 kPa, and a relative humidity of 63 to 67%.
DESCRIPTION VALUE
Capacitance range (E6 series); note 1 33 nF to 4.7 µF
Tolerance on capacitance after 1000 hours ±10%
Tan δ; note 1 5%
Insulation resistance after 1 minute at UR (DC) Rins × C 500 seconds
Maximum capacitance change as a function of temperature ±15%
Ageing typical 3% per time decade
Resistance to soldering heat 260 °C; 10 seconds
Note
1. Measured at 20
°C, 1 V and 1 kHz, using a four-gauge method.
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 8 www.yageo.com
TESTS AND REQUIREMENTS
Table 3 Test procedures and requirements
IEC
60384-10/
CECC 32 100
CLAUSE
IEC
60068-2
TEST
METHOD
TEST PROCEDURE REQUIREMENTS
4.4 mounting the capacitors may be mounted
on printed-circuit boards or
ceramic substrates by applying
wave soldering, reflow soldering
(including vapour phase
soldering) or conductive adhesive
no visible damage
4.5 visual inspection and
dimension check
any applicable method using
×10 magnification
in accordance with
specification
4.6.1 capacitance f = 1 kHz; measuring voltage
1 Vrms at 20 °C
within specified tolerance
4.6.2 tan
δ f = 1 kHz; measuring voltage
1 Vrms at 20 °C
in accordance with
specification
4.6.3 insulation resistance at UR (DC) for 1 minute in accordance with
specification
4.6.4 voltage proof
2.5 × UR for 1 minute; no breakdown or
flashover
4.7.1 temperature
characteristic
between minimum and
maximum temperature
in accordance with
specification
4.8 adhesion a force of 5 N applied for 10 s to
the line joining the terminations
and in a plane parallel to the
substrate
no visible damage
mounted in accordance with
CECC 32 100, paragraph 4.4
no visible damage 4.9 bond strength of
plating on end face
conditions: bending
1 mm at a rate of 1 mm/s,
radius jig. 340 mm
C/C: 10%
resistance to
soldering heat
precondition:
120 to 150 °C for 1 minute;
260 ±5 °C for 10 ±0.5 s
the terminations shall be
well tinned after recovery
C/C: 10%
4.10 Tb
resistance to
leaching; jig clamps
to the second
component in the
longitudinal line
260 ±5 °C for 30 ±1 s
in a static solder bath
using visual enlargement
of ×10, dissolution of the
terminations shall not
exceed 10%
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 9 www.yageo.com
IEC
60384-10/
CECC 32 100
CLAUSE
IEC
60068-2
TEST
METHOD
TEST PROCEDURE REQUIREMENTS
4.11 Ta solderability zero hour test, and test after
storage (20 to 24 months) in
original packing in normal
atmosphere; unmounted chips
completely immersed for 2 ±0.5 s
in a solder bath at 235 ±5 °C
the terminations shall be well
tinned
4.12 Na rapid change
of temperature
preconditioning; 5 cycles in the
following sequence:
30 minutes at 55°C, change
within 30 minutes to +125 °C
no visible damage after
48 hours recovery:
C/C: 15%
4.14 Ca damp heat,
steady state
initialization:
48 hours after UR at 40 °C for 1
hour (for initial value
measurement); 500 ±12 hours at
40 °C; 90 to 95% RH; UR applied
preconditioning:
UR at 40 °C for 1 hour after 48
hours recovery:
C/C: ±15%
tan δ: 7%
Rins: 500 M or RiCR 25 s,
whichever is less
4.15 endurance preconditioning:
2 × UR at 125 °C for 1 hour hour
(initial value is measured after 48
hours, recovery at room
temperature); 1000 hours at 125
°C and 2 ×UR applied
after 48 hours recovery:
C/C: ±20%
tan δ: 7%
Rins: 2000 M or RiCR 50 s,
whichever is less
Phycomp Product specification
Surface-mount ceramic
multilayer capacitors
Class 2, X7R
10 V
2005 Jan 14 Rev.9 10 www.yageo.com
REVISION HISTORY
Revision Date Change
Notification
Description
Rev.9 2005 Jan 14 - - Capacitance range extended
Rev.8 2003 Sep 26 - - Size 1206 L1 dimensions revised.
- Size 0402 and 0603 capacitance range expanded, refer to
selection chart.
Rev.7 2003 Jun 26 - -
Rev.6 2003 Mar 25 - - Updated company logo.
Rev.5 2002 Jul 15 - - Capacitance range changed from E6 into E12.
- Capacitance range expanded to 4.7 µF.
- Figures 3 through 7 corrected.
print-friendly version
Product Detail Information
Product Group Multilayer Capacitor Chips and Arrays
Ordering Code CC0402KRX7R6BB473
Ordering Code 223824715645
Unified CTC C0402KRX7R6BB473
Additional Product Code 04022R473K6B20D
Description General purpose, 0402, X7R, 47nF, ?±10%, 10V, 7" paper
Status Standard
Size Code 0402
Capacitance Tolerance +-10%
Packing Style Paper Tape & 180mm (7") Reel
Dielectric Material (TC) X7R
Rated Voltage 10V
Capacitance 47 nF
Related Data Sheets, Catalogs and Application Notes:
Datasheet - X7R 10 V, Rev.9 [211 kb]
Product Selection Guide 2008 (revision 1) [3.65 MB]
Yageo Passive Components 2008 [3.26 mb]
Material declaration MLCCs type X7R, [85 kb]
Environmental declaration
Appl. note - DC, AC and Pulse load of Multilayer Ceramic Capacitors [308 kb]
MLCC sample kits [177 kb]
Appl. manual - MLCC application manual [577 kb]
Datasheet - MLCC introduction, Rev.9 [98 kb]
Datasheet - MLCC general data of packing, labelling, mounting, tests & requirements;
Rev.7 [159 kb]
Flowchart - Quality Flowchart, Rev.4 [80kb]
Calculation tool - MLCC Spice Data
General info - Standard Values in a Decade [8.39 kb]
Requirements, Rev.7 [158 kb]
For optimal printing of Data sheets print from page 2 of the PDF.
Note Clear Text Codes in the data sheets can differ from the Clear Text Codes displayed above.
The CTC displayed above is a new code which has been introduced to align product codes in the
complete Yageo organisation. You can search products with the CTC displayed in the data sheet
by using the competitor part number search function.
Documents are in PDF format so to view and print them you will need Adobe Acrobat Reader
installed on your computer. This is available free of charge.
Copyright © 2002-2005 Yageo Corporation
Privacy Policy | Access to and use of this web site is subject to the following Terms of use
Springsite Technology