Instruction Sheet 408-8676 Production Torque Wrenches PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. Open-End Wrench Head Torque Wrench TE CONNECTIVITY PART NUMBER PREVIOUS PART NUMBER 1055276-1 2098-0351-54 1055419-1 WRENCH DESCRIPTION Protective Cover WRENCH SIZE PRESET TORQUE mm [inches] Production Torque Wrench 6.4 1/4 14 in-lbs 2 lb 2098-5065-54 For SMA (OSM) Type Connectors 7.9 5/16 8 in.-lbs +1.5/-.5 lb 1055480-1 2098-5304-54 For OSSM Type Connectors 6.4 1/4 5 in.-lbs .5 lb 1055512-1 2098-5619-54 For SMA (OSM) Hermetic Type Connectors 7.1 9/32 30 in.-lbs 2 lb 1055546-1 2098-5830-54 Production Torque Wrench Kit 6.4 and 8.0 1/4 and 5/16 8 in.-lbs +1.5/-.5 lb 1055790-1 2598-5026-54 For SC/N Type Connectors (Hex Nut Design) 20.6 13/16 14 in.-lbs 2 lb 1055791-1 2598-5027-54 For TNC Type Connectors (Hex Nut Design) 15.9 5/8 14 in.-lbs 2 lb 1055826-1 2598-5160-54 Production Torque Wrench 4.0 5/32 8 in.-lbs +1.5/-.5 lb 1055868-1 2598-5298-54 For TNC Type Connectors (Hex Nut Design) 14.3 9/16 14 in.-lbs2 lb 1061789-1 7098-5031-54 For 7mm Type Connectors 19.1 3/4 14 in.-lbs 2 lb 1490262-1 2598-5383-50 Production Torque Wrench 7.9 5/16 15 in.-lbs 2 lb Figure 1 1. INTRODUCTION These production torque wrenches are used to properly install or disassemble the connectors listed in Figure 1. Figure 1 also contains the TE part numbers for the wrenches, the previous part numbers for the wrenches, wrench size, and the preset torque for each wrench. NOTE Dimensions on this sheet are in metric units [with U.S. customary units in brackets], unless otherwise noted. Reason for revision is provided in Section 5, REVISION SUMMARY. 2. DESCRIPTION Each production torque wrench contains a protective cover, a torque wrench, and an interchangeable head. Refer to Figure 2 for the appropriate replacement wrench head part numbers. The wrenches are designed to be used in the clockwise or counterclockwise direction. (c) 2014 TE Connectivity family of companies All Rights Reserved *Trademark TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 2 ORIGINAL INSTRUCTIONS 27 OCT 14 Rev G 408-8676 3. OPERATION OF THE WRENCHES NOTE If a wrench has not been used recently, move the wrench head back and forth several times, listening for audible "clicks." Clicking the wrench head back and forth spreads lubricant throughout the internal mechanism to improve wrench performance. WRENCH SIZE TE CONNECTIVITY PART NUMBER mm [inches] 1406504-1 6.4 [1/4] 1406504-2 8.0 [5/16] 1406504-3 9.6 [3/8] 1406504-4 12.8 [1/2] 1406504-5 19.6 [3/4] 1406504-6 11.2 [7/16] 1406504-7 7.1 [9/32] 1406504-8 10.4 [13/32] 1406504-9 17.6 [11/16] 1-1406504-0 14.6 [9/16] 1-1406504-1 8.8 [11/32] 1-1406504-2 16.0 [5/8] 1-1406504-3 20.8 [13/16] 1-1406504-4 4.0 [5/32] 1-1406504-5 6.1 [15/64] Figure 2 Using the appropriate sized head (Figure 1), turn the wrench clockwise (or counterclockwise) until there is an audible "click." This "click" indicates that the proper torque has been achieved. CAUTION Do NOT over-tighten the connector with the torque wrench. Over-tightening the wrench could result in inaccurate torque settings. CAUTION Do not use or re-terminate damaged connectors. 4. REPLACEMENT Remove the wrench head by pulling it off the production torque wrench. Then replace the head with the appropriate head listed in Figure 2. Order replacement parts through your TE Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 5. REVISION SUMMARY Updated document to corporate requirements Added tolerances to table in Figure 1 Rev G 2 of 2