74AXP1T125 Dual supply buffer/line driver; 3-state Rev. 1 -- 21 December 2015 Product data sheet 1. General description The 74AXP1T125 is a dual supply non-inverting buffer/line driver with 3-state output. It features one input (A), an output (Y), an output enable input (OE) and dual supply pins (VCCI and VCCO). A HIGH level at pin OE causes the output to assume a high-impedance OFF-state. The inputs are referenced to VCCI and the output is referenced to VCCO. All inputs can be connected directly to VCCI or GND. VCCI can be supplied at any voltage between 0.7 V and 2.75 V and VCCO can be supplied at any voltage between 1.2 V and 5.5 V. This feature allows voltage level translation. Schmitt-trigger action at all inputs makes the circuit tolerant of slower input rise and fall times. This device ensures very low static and dynamic power consumption across the entire supply range and is fully specified for partial power down applications using IOFF. The IOFF circuitry disables the output, preventing the potentially damaging backflow current through the device when it is powered down. 2. Features and benefits Wide supply voltage range: VCCI: 0.7 V to 2.75 V VCCO: 1.2 V to 5.5 V Low input capacitance; CI = 0.6 pF (typical) Low output capacitance; CO = 1.8 pF (typical) Low dynamic power consumption; CPD = 0.4 pF at VCCI = 1.2 V (typical) Low dynamic power consumption; CPD = 7.1 pF at VCCO = 3.3 V (typical) Low static power consumption; ICCI = 0.5 A (85 C maximum) Low static power consumption; ICCO = 1.8 A (85 C maximum) High noise immunity Complies with JEDEC standard: JESD8-12A.01 (1.1 V to 1.3 V; A, OE inputs) JESD8-11A.01 (1.4 V to 1.6 V) JESD8-7A (1.65 V to 1.95 V) JESD8-5A.01 (2.3 V to 2.7 V) JESD8-C (2.7 V to 3.6 V; Y output) JESD12-6 (4.5 V to 5.5 V; Y output) ESD protection: HBM ANSI/ESDA/JEDEC JS-001 Class 2 exceeds 2 kV CDM JESD22-C101E exceeds 1000 V 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Latch-up performance exceeds 100 mA per JESD78D Class II Inputs accept voltages up to 2.75 V Low noise overshoot and undershoot < 10% of VCCO IOFF circuitry provides partial power-down mode operation Multiple package options Specified from 40 C to +85 C 3. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description Version SOT363 74AXP1T125GW 40 C to +85 C SC-88 plastic surface-mounted package; 6 leads 74AXP1T125GM 40 C to +85 C XSON6 plastic extremely thin small outline package; no leads; SOT886 6 terminals; body 1 1.45 0.5 mm 74AXP1T125GN 40 C to +85 C XSON6 extremely thin small outline package; no leads; 6 terminals; body 0.9 1.0 0.35 mm SOT1115 74AXP1T125GS 40 C to +85 C XSON6 extremely thin small outline package; no leads; 6 terminals; body 1.0 1.0 0.35 mm SOT1202 4. Marking Table 2. Marking Type number Marking code[1] 74AXP1T125GW rN 74AXP1T125GM rN 74AXP1T125GN rN 74AXP1T125GS rN [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 5. Functional diagram $ $ < < 2( 2( 9&&, 9&&2 DDD DDD Fig 1. Logic symbol 74AXP1T125 Product data sheet Fig 2. Logic diagram All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 2 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 6. Pinning information 6.1 Pinning $;37 $;37 9&&, *1' $ 9&&2 9&&, 9&&2 *1' 2( $ < 2( < DDD 7UDQVSDUHQWWRSYLHZ DDD Fig 3. Pin configuration SOT363 Fig 4. Pin configuration SOT886, SOT1115 and SOT1202 (XSON6) 6.2 Pin description Table 3. Pin description Symbol Pin Description VCCI 1 input supply voltage GND 2 ground (0 V) A 3 data input A Y 4 data output Y OE 5 output enable input VCCO 6 output supply voltage 7. Functional description Table 4. Function table[1] Supply voltage Input Output VCCI VCCO OE A Y 0.7 V to 2.75 V 1.2 V to 5.5 V L L L 0.7 V to 2.75 V 1.2 V to 5.5 V L H H 0.7 V to 2.75 V 1.2 V to 5.5 V H X Z GND 1.2 V to 5.5 V X X Z 0.7 V to 2.75 V GND X X Z GND GND X X Z [1] H = HIGH voltage level; L = LOW voltage level; X = Don't care; Z = high-impedance OFF-state. 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 3 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 8. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Max Unit VCCI input supply voltage 0.5 3.3 V VCCO output supply voltage 0.5 6.0 V IIK input clamping current 50 - [1] 0.5 3.3 50 - [1][2] 0.5 VCCO + 0.5 V [1] 0.5 6.0 V - 25 mA VI < 0 V VI input voltage IOK output clamping current VO < 0 V VO output voltage Active mode Power-down or 3-state mode IO output current VO = 0 V to VCCO mA V mA ICCI input supply current - 50 mA ICCO output supply current - 50 mA IGND ground current 50 - mA Tstg storage temperature 65 +150 C Ptot total power dissipation - 250 mW Tamb = 40 C to +85 C [1] The minimum input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] VCCO + 0.5 V should not exceed 6.0 V. [3] For SOT363 package: above 82.5 C the value of Ptot derates linearly with 3.7 mW/K. For SOT886 package: above 75 C the value of Ptot derates linearly with 3.3 mW/K. For SOT1115 package: above 70 C the value of Ptot derates linearly with 3.2 mW/K. For SOT1202 package: above 75 C the value of Ptot derates linearly with 3.3 mW/K. 9. Recommended operating conditions Table 6. Recommended operating conditions Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCCI Min Max Unit input supply voltage 0.7 2.75 V VCCO output supply voltage 1.2 5.5 V VI input voltage VO output voltage Tamb ambient temperature t/V input transition rise and fall rate 74AXP1T125 Product data sheet Conditions 0 2.75 V Active mode 0 VCCO V Power-down or 3-state mode 0 5.5 V 40 +85 C 0 200 ns/V VCCI = 0.7 V to 2.75 V All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 4 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 10. Static characteristics Table 7. Static characteristics At recommended operating conditions, unless otherwise specified; voltages are referenced to GND (ground = 0 V). Symbol Parameter Tamb = 40 C to +85 C Conditions Min HIGH-level input voltage VIH LOW-level input voltage VIL HIGH-level output voltage 0.75VCCI - - - V VCCI = 1.1 V to 1.95 V 0.65VCCI - - - V VCCI = 2.3 V to 2.7 V 1.6 - - - V VCCI = 0.75 V to 0.85 V - - 0.25VCCI 0.25VCCI V VCCI = 1.1 V to 1.95 V - - 0.35VCCI 0.35VCCI V - - 0.7 0.7 V - 1.05 - - V IO = 3 mA; VCCO = 1.4 V 1.05 - - - V IO = 4.5 mA; VCCO = 1.65 V 1.2 - - - V IO = 8 mA; VCCO = 2.3 V 1.7 - - - V IO = 10 mA; VCCO = 3.0 V 2.2 - - - V 3.7 - - - V - 0.18 - - V IO = 3 mA; VCCO = 1.4 V - - 0.35 0.35 V IO = 4.5 mA; VCCO = 1.65 V - - 0.45 0.45 V IO = 8 mA; VCCO = 2.3 V - - 0.7 0.7 V IO = 10 mA; VCCO = 3.0 V - - 0.8 0.8 V - - 0.8 0.8 V - 0.001 0.1 0.5 A - 0.001 0.1 0.5 A IO = 2 mA; VCCO = 1.2 V [1] IO = 12 mA; VCCO = 4.5 V LOW-level output voltage VOL Typ 25 C Max 25 C Max 85 C VCCI = 0.75 V to 0.85 V VCCI = 2.3 V to 2.7 V VOH Unit IO = 2 mA; VCCO = 1.2 V [1] IO = 12 mA; VCCO = 4.5 V [1] II input leakage current VI = 0 V to 2.75 V; VCCI = 0 V to 2.75 V IOZ OFF-state output current VO = 0 V to 5.5 V; VCCO = 1.2 V to 5.5 V IOFF power-off leakage current inputs; VI = 0 V to 2.75 V; VCCI = 0 V; VCCO = 0 V to 5.5 V [1] - 0.01 0.1 0.5 A output; VO = 0 V to 5.5 V; VCCO = 0 V; VCCI = 0 V to 2.75 V; VI = 0 V to 2.75 V [1] - 0.01 0.1 0.5 A inputs; VI = 0 V or 2.75 V; VCCI = 0 V to 0.1 V; VCCO = 0 V to 5.5 V [1] - 0.02 0.1 0.5 A output; VO = 0 V or 5.5 V; VCCO = 0 V to 0.1 V; VCCI = 0 V to 2.75 V; VI = 0 V or 2.75 V [1] - 0.02 0.1 0.5 A IOFF [1] additional power-off leakage current Typical values are measured at VCCI = VCCO = 1.2 V unless otherwise specified. 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 5 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Table 8. Static characteristics supply current At recommended operating conditions, unless otherwise specified; voltages are referenced to GND (ground = 0 V). Symbol Parameter ICCI input supply current ICCO output supply current Tamb = 40 C to +85 C Conditions Max 85 C [1] 1 100 10 300 nA VCCI = 1.3 V to 2.75 V [2] 1 100 20 500 nA VCCI = 2.75 V; VCCO = 0 V 1 100 20 500 nA VCCI = 0 V; VCCO = 5.5 V 1 100 1 100 nA 0.001 1.0 0.01 1.2 A 0.8 1.5 1.0 1.8 A VCCI = 2.75 V; VCCO = 0 V 0.001 0.1 0.003 0.2 A VCCI = 0 V; VCCO = 3.6 V 0.2 0.6 0.3 0.8 A VCCI = 0 V; VCCO = 5.5 V 0.4 0.8 0.5 1.0 A VI = VCCI 0.5 V; VCCI = 2.5 V 2 100 14 150 A VI = 0 V or VCCI; IO = 0 A; see Table 9 [1] [3] [1] Typical values are measured at VCCI = VCCO = 1.2 V. [2] Typical values are measured at VCCI = VCCO = 2.5 V. [3] Typical values are measured at VCCI = 1.2 V and VCCO = 5.0 V. Table 9. Typ 85 C VCCI = 0.7 V to 1.3 V VCCO = 3.6 V to 5.5 V additional input supply current Max 25 C VI = 0 V or VCCI; VCCO = 1.2 V to 3.6 V ICCI Unit Typ 25 C Typical output supply current (ICCO ) VCCI VCCO 0V 1.2 V 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V 0V 0 1 5 20 100 200 400 nA 0.8 V 1 10 150 200 300 500 800 nA 1.2 V 1 1 5 200 300 500 800 nA 1.5 V 1 1 5 100 300 500 800 nA 1.8 V 1 1 5 100 300 500 800 nA 2.5 V 1 1 5 100 100 500 800 nA 74AXP1T125 Product data sheet Unit All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 6 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 11. Dynamic characteristics Table 10. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13; for wave form see Figure 5 and Figure 6. Symbol Parameter Conditions VCCO 1.5 V 0.1 V 1.2 V Typ[1] Unit Min Typ[1] 1.8 V 0.15 V Max Min Typ[1] Max Tamb = 25 C tpd propagation A to Y delay VCCI = 0.75 V to 0.85 V [2] 22 3 16 61 3 15 57 ns VCCI = 1.1 V to 1.3 V 16.2 3.1 10.3 19.8 2.8 8.2 15.8 ns VCCI = 1.4 V to 1.6 V 15.4 2.8 9.5 18.2 2.5 7.4 13.2 ns VCCI = 1.65 V to 1.95 V 15.0 2.7 9.1 17.4 2.4 7.0 11.9 ns 14.7 2.5 8.7 16.9 2.2 6.6 11.1 ns 25 3 20 76 3 18 72 ns 17.9 3.1 11.3 18.9 2.8 9.0 15.5 ns VCCI = 2.3 V to 2.7 V ten [3] enable time OE to Y VCCI = 0.75 V to 0.85 V VCCI = 1.1 V to 1.3 V VCCI = 1.4 V to 1.6 V 16.9 2.8 10.3 17.5 2.5 8.1 13.9 ns VCCI = 1.65 V to 1.95 V 16.5 2.7 9.9 16.9 2.4 7.6 13.3 ns 16.0 2.5 9.4 16.4 2.2 7.1 12.7 ns VCCI = 2.3 V to 2.7 V tdis [4] disable time OE to Y VCCI = 0.75 V to 0.85 V 25 3 20 76 3 20 72 ns VCCI = 1.1 V to 1.3 V 17.1 3.1 12.0 18.3 2.8 11.3 17.4 ns VCCI = 1.4 V to 1.6 V 16.1 2.8 11.1 17.4 2.5 10.3 16.0 ns VCCI = 1.65 V to 1.95 V 15.6 2.7 10.6 16.5 2.4 9.9 15.5 ns VCCI = 2.3 V to 2.7 V 15.0 2.5 10.0 16.3 2.2 9.4 15.0 ns 22 3 16 136 3 15 133 ns VCCI = 1.1 V to 1.3 V 16.2 3.1 10.3 19.8 2.8 8.2 15.8 ns VCCI = 1.4 V to 1.6 V 15.4 2.8 9.5 18.2 2.5 7.4 13.2 ns VCCI = 1.65 V to 1.95 V 15.0 2.7 9.1 17.4 2.4 7.0 11.9 ns 14.7 2.5 8.7 16.9 2.2 6.6 11.1 ns 25 3 20 151 3 18 148 ns VCCI = 1.1 V to 1.3 V 17.9 3.1 11.3 18.9 2.8 9.0 15.5 ns VCCI = 1.4 V to 1.6 V 16.9 2.8 10.3 17.5 2.5 8.1 13.9 ns VCCI = 1.65 V to 1.95 V 16.5 2.7 9.9 16.9 2.4 7.6 13.3 ns VCCI = 2.3 V to 2.7 V 16.0 2.5 9.4 16.4 2.2 7.1 12.7 ns Tamb = 40 C to +85 C tpd propagation A to Y delay VCCI = 0.75 V to 0.85 V [2] VCCI = 2.3 V to 2.7 V ten [3] enable time OE to Y VCCI = 0.75 V to 0.85 V 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 7 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Table 10. Dynamic characteristics ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13; for wave form see Figure 5 and Figure 6. Symbol Parameter tdis Conditions VCCO VCCI = 0.75 V to 0.85 V VCCI = 1.1 V to 1.3 V 1.5 V 0.1 V Typ[1] Min Typ[1] 1.8 V 0.15 V Max Min Typ[1] Max 25 3 20 151 3 20 148 ns 17.1 3.1 12.0 18.3 2.8 11.3 17.4 ns VCCI = 1.4 V to 1.6 V 16.1 2.8 11.1 17.4 2.5 10.3 16.0 ns VCCI = 1.65 V to 1.95 V 15.6 2.7 10.6 16.5 2.4 9.9 15.5 ns 15.0 2.5 10.0 16.3 2.2 9.4 15.0 ns - 1.0 - - 1.0 - - ns VCCI = 2.3 V to 2.7 V transition time 1.2 V [4] disable time OE to Y tt Unit [5] VCCI = 0.75 V to 2.7 V [1] Typical values are measured at nominal supply voltages and Tamb = +25 C. [2] tpd is the same as tPLH and tPHL. [3] ten is the same as tPZH and tPZL. [4] tdis is the same as tPHZ and tPLZ. [5] tt is the same as tTHL and tTLH. Table 11. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13; for wave form see Figure 5 and Figure 6. Symbol Parameter Conditions VCCO Unit 2.5 V 0.2 V 3.3 V 0.3 V Min Typ[1] Max Min Typ[1] 5.0 V 0.5 V Max Min 2 13 57 2 13 65 2 14 77 ns 2.4 6.5 10.8 2.2 5.9 9.5 2.1 5.6 9.0 ns Typ[1] Max Tamb = 25 C tpd propagation A to Y delay VCCI = 0.75 V to 0.85 V [2] VCCI = 1.1 V to 1.3 V VCCI = 1.4 V to 1.6 V 2.1 5.7 9.1 2.0 5.1 8.2 1.9 4.8 7.7 ns VCCI = 1.65 V to 1.95 V 2.0 5.3 8.7 1.8 4.7 7.7 1.8 4.4 7.3 ns 1.9 4.9 8.1 1.7 4.3 7.1 1.6 4.0 6.6 ns 92 ns VCCI = 2.3 V to 2.7 V ten [3] enable time OE to Y 2 17 72 2 17 80 2 20 VCCI = 1.1 V to 1.3 V VCCI = 0.75 V to 0.85 V 2.4 7.2 12.5 2.2 6.7 11.4 2.1 6.5 11.2 ns VCCI = 1.4 V to 1.6 V 2.1 6.3 11.0 2.0 5.7 10.2 1.9 5.5 9.8 ns VCCI = 1.65 V to 1.95 V 2.0 5.8 10.5 1.8 5.2 9.8 1.8 5.0 9.2 ns 1.9 5.3 9.9 1.7 4.7 9.1 1.6 4.5 8.6 ns 2 17 72 2 18 80 2 16 92 ns VCCI = 1.1 V to 1.3 V 2.4 9.2 14.2 2.2 9.9 15.2 2.1 8.3 13.2 ns VCCI = 1.4 V to 1.6 V 2.1 8.2 13.1 2.0 9.1 14.1 1.9 7.4 12.1 ns VCCI = 1.65 V to 1.95 V 2.0 7.8 12.6 1.8 8.6 13.7 1.8 7.0 11.7 ns VCCI = 2.3 V to 2.7 V 1.9 7.2 12.1 1.7 8.1 13.2 1.6 6.5 11.2 ns VCCI = 2.3 V to 2.7 V tdis disable time 74AXP1T125 Product data sheet [4] OE to Y VCCI = 0.75 V to 0.85 V All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 8 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Table 11. Dynamic characteristics ...continued Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13; for wave form see Figure 5 and Figure 6. Symbol Parameter Conditions VCCO Unit 2.5 V 0.2 V 3.3 V 0.3 V Min Typ[1] Max Min Typ[1] 5.0 V 0.5 V Max Min 2 13 152 2 13 179 2 14 210 ns VCCI = 1.1 V to 1.3 V 2.4 6.5 10.8 2.2 5.9 9.5 2.1 5.6 9.0 ns VCCI = 1.4 V to 1.6 V 2.1 5.7 9.1 2.0 5.1 8.2 1.9 4.8 7.7 ns VCCI = 1.65 V to 1.95 V 2.0 5.3 8.7 1.8 4.7 7.7 1.8 4.4 7.3 ns 1.9 4.9 8.1 1.7 4.3 7.1 1.6 4.0 6.6 ns 2 17 167 2 17 194 2 20 225 ns VCCI = 1.1 V to 1.3 V 2.4 7.2 12.5 2.2 6.7 11.4 2.1 6.5 11.2 ns VCCI = 1.4 V to 1.6 V 2.1 6.3 11.0 2.0 5.7 10.2 1.9 5.5 9.8 ns VCCI = 1.65 V to 1.95 V 2.0 5.8 10.5 1.8 5.2 9.8 1.8 5.0 9.2 ns VCCI = 2.3 V to 2.7 V 1.9 5.3 9.9 1.7 4.7 9.1 1.6 4.5 8.6 ns 2 17 167 2 18 194 2 16 225 ns VCCI = 1.1 V to 1.3 V 2.4 9.2 14.2 2.2 9.9 15.2 2.1 8.3 13.2 ns VCCI = 1.4 V to 1.6 V 2.1 8.2 13.1 2.0 9.1 14.1 1.9 7.4 12.1 ns VCCI = 1.65 V to 1.95 V 2.0 7.8 12.6 1.8 8.6 13.7 1.8 7.0 11.7 ns 1.9 7.2 12.1 1.7 8.1 13.2 1.6 6.5 11.2 ns 1.0 - - 1.0 - - 1.0 - Typ[1] Max Tamb = 40 C to +85 C propagation A to Y delay VCCI = 0.75 V to 0.85 V tpd [2] VCCI = 2.3 V to 2.7 V [3] enable time OE to Y ten VCCI = 0.75 V to 0.85 V disable time tdis [4] OE to Y VCCI = 0.75 V to 0.85 V VCCI = 2.3 V to 2.7 V transition time tt [1] VCCO = 5.5 V [5] - ns Typical values are measured at nominal supply voltages and tamb = +25 C. [2] tpd is the same as tPLH and tPHL. [3] ten is the same as tPZH and tPZL. [4] tdis is the same as tPHZ and tPLZ. [5] tt is the same as tTHL and tTLH. 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 9 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Table 12. Typical dynamic characteristics at Tamb = 25 C Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 13; for wave form see Figure 5 and Figure 6. Symbol Parameter CPD power dissipation capacitance Conditions VCCO Unit 1.2 V 1.5 V 1.8 V 2.5 V 3.3 V 5.0 V VCCI = 0.8 V 0.4 0.4 0.4 0.4 0.4 0.4 pF VCCI = 1.2 V 0.4 0.4 0.4 0.4 0.4 0.4 pF VCCI = 1.5 V 0.5 0.5 0.5 0.5 0.5 0.5 pF VCCI = 1.8 V 0.5 0.5 0.5 0.5 0.5 0.5 pF 0.7 0.7 0.7 0.7 0.7 0.7 pF VCCI = 0.8 V 6.7 6.8 6.8 6.9 7.5 9.5 pF VCCI = 1.2 V 6.8 6.9 7.0 7.0 7.1 7.6 pF VCCI = 1.5 V 6.9 6.9 6.9 7.0 7.1 7.6 pF VCCI = 1.8 V 6.9 6.9 6.9 7.0 7.2 7.6 pF VCCI = 2.5 V 6.9 7.0 7.0 7.0 7.2 7.6 pF fi = 1 MHz; RL = ; VI = 0 V to VCCI [1] [2] input supply VCCI = 2.5 V [3] output supply CI input capacitance VI = 0 V or VCCI; VCCI = 0 V to 2.7 V 0.6 0.6 0.6 0.6 0.6 0.6 pF CO output capacitance VO = 0 V; VCCO = 0 V 1.8 1.8 1.8 1.8 1.8 1.8 pF [1] CPD is used to determine the dynamic power dissipation (PD in W). [2] Power dissipated from input supply (VCCI) PD = CPD VCCI2 fi N where: CPD = power dissipation capacitance of the input supply. VCCI = input supply voltage in V; fi = input frequency in MHz; N = number of inputs switching; [3] Power dissipated from output supply (VCCO) PD = (CL + CPD) VCCO2 fo where: CL = load capacitance in pF; CPD = power dissipation capacitance of the output supply. VCCO = output supply voltage in V; fo = output frequency in MHz; 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 10 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 11.1 Waveforms and graphs 9, $LQSXW 90 90 9 W3+/ 92+ W3/+ <RXWSXW 90 90 92/ W7+/ W7/+ DDD Measurement points are given in Table 13. VOL and VOH are typical output voltage levels that occur with the output load. Fig 5. Input A to output Y propagation delay times and output transition times 9, 2(LQSXW 90 *1' W3/= W3=/ 9&&2 RXWSXW /2:WR2)) 2))WR/2: 90 9; 92/ W3+= 92+ W3=+ 9< RXWSXW +,*+WR2)) 2))WR+,*+ 90 *1' RXWSXWV HQDEOHG RXWSXWV GLVDEOHG RXWSXWV HQDEOHG DDD Measurement points are given in Table 13. VOL and VOH are typical output voltage levels that occur with the output load. Fig 6. Table 13. Enable and disable times Measurement points Supply voltage VCCI Output VCCO Input VM VX VY VM VI 0.75 V to 2.7 V 1.2 V to 1.6 V 0.5VCCO VOL + 0.1 V VOH 0.1 V 0.5VCCI VCCI 0.75 V to 2.7 V 1.65 V to 2.7 V 0.5VCCO VOL + 0.15 V VOH 0.15 V 0.5VCCI VCCI 0.75 V to 2.7 V 3.0 V to 5.5 V 0.5VCCO VOL + 0.3 V VOH 0.3 V 0.5VCCI VCCI 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 11 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state DDD WSG QV DDD WSG QV &/ S) Tamb = 40 C to +85 C unless otherwise specified. Tamb = 40 C to +85 C unless otherwise specified. For tPLH, tPHL, tPZH and tPZL For tPLH, tPHL, tPZH and tPZL (1) Minimum: VCCO = 5.5 V (1) Minimum: VCCO = 3.6 V (2) Typical: Tamb = 25 C; VCCO = 5 V (2) Typical: Tamb = 25 C; VCCO = 3.3 V (3) Maximum: VCCO = 4.5 V (3) Maximum: VCCO = 3 V Fig 7. &/ S) Additional propagation delay versus load capacitance DDD Fig 8. Additional propagation delay versus load capacitance DDD WSG QV WSG QV &/ S) Tamb = 40 C to +85 C unless otherwise specified. For tPLH, tPHL, tPZH and tPZL Tamb = 40 C to +85 C unless otherwise specified. For tPLH, tPHL, tPZH and tPZL (1) Minimum: VCCO = 2.7 V (1) Minimum: VCCO = 1.95 V (2) Typical: Tamb = 25 C; VCCO = 2.5 V (2) Typical: Tamb = 25 C; VCCO = 1.8 V (3) Maximum: VCCO = 2.3 V (3) Maximum: VCCO = 1.65 V Fig 9. Additional propagation delay versus load capacitance 74AXP1T125 Product data sheet &/ S) Fig 10. Additional propagation delay versus load capacitance All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 12 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state DDD DDD WSG QV WSG QV &/ S) &/ S) Tamb = 40 C to +85 C unless otherwise specified. Tamb = 25 C; VCCO = 1.2 V. For tPLH, tPHL, tPZH and tPZL For tPLH, tPHL, tPZH and tPZL (1) Minimum: VCCO = 1.6 V (2) Typical: Tamb = 25 C; VCCO = 1.5 V (3) Maximum: VCCO = 1.4 V Fig 11. Additional propagation delay versus load capacitance 74AXP1T125 Product data sheet Fig 12. Additional propagation delay versus load capacitance All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 13 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 9, QHJDWLYH SXOVH W: 90 9 WI WU WU WI 9, SRVLWLYH SXOVH 9 90 90 90 W: 9(;7 9&&, 9&&2 9, * 5/ 92 '87 57 &/ 5/ DDD Test data is given in Table 14. Definitions test circuit: RT = termination resistance should be equal to output impedance Zo of the pulse generator. CL = load capacitance including jig and probe capacitance. RL = Load resistance. Fig 13. Test circuit for measuring switching times Table 14. Test data Supply voltage VCCI Load VCCO CL 0.75 V to 2.7 V 1.2 V to 5.5 V 5 pF 74AXP1T125 Product data sheet Input VEXT RL tr, tf VI tPLH, tPHL tPZH, tPHZ tPZL, tPLZ 10 k 3.0 ns VCCI GND GND 2VCCO All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 14 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 12. Package outline 3ODVWLFVXUIDFHPRXQWHGSDFNDJHOHDGV 627 ' % $ ( \ ; +( Y 0 $ 4 SLQ LQGH[ $ $ H ES F /S Z 0 % H GHWDLO; PP VFDOH ',0(16,216 PPDUHWKHRULJLQDOGLPHQVLRQV 81,7 $ $ PD[ ES F ' ( H H +( /S 4 Y Z \ PP 287/,1( 9(56,21 5()(5(1&(6 ,(& -('(& -(,7$ 6& 627 (8523($1 352-(&7,21 ,668('$7( Fig 14. Package outline SOT363 (SC-88) 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 15 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 627 ;621SODVWLFH[WUHPHO\WKLQVPDOORXWOLQHSDFNDJHQROHDGVWHUPLQDOVERG\[[PP E [ / / H H H [ $ $ ' ( WHUPLQDO LQGH[DUHD PP VFDOH 'LPHQVLRQV PPDUHWKHRULJLQDOGLPHQVLRQV 8QLW PP PD[ QRP PLQ $ $ E ' ( H H / / 1RWHV ,QFOXGLQJSODWLQJWKLFNQHVV &DQEHYLVLEOHLQVRPHPDQXIDFWXULQJSURFHVVHV 2XWOLQH YHUVLRQ 627 VRWBSR 5HIHUHQFHV ,(& -('(& -(,7$ (XURSHDQ SURMHFWLRQ ,VVXHGDWH 02 Fig 15. Package outline SOT886 (XSON6) 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 16 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state ;621H[WUHPHO\WKLQVPDOORXWOLQHSDFNDJHQROHDGV WHUPLQDOVERG\[[PP 627 E i / / H H H i $ $ ' ( WHUPLQDO LQGH[DUHD 'LPHQVLRQV 8QLW PP PP VFDOH $ $ E ' ( H / H PD[ QRP PLQ / 1RWH ,QFOXGLQJSODWLQJWKLFNQHVV 9LVLEOHGHSHQGLQJXSRQXVHGPDQXIDFWXULQJWHFKQRORJ\ VRWBSR 5HIHUHQFHV 2XWOLQH YHUVLRQ ,(& -('(& -(,7$ 627 (XURSHDQ SURMHFWLRQ ,VVXHGDWH Fig 16. Package outline SOT1115 (XSON6) 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 17 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state ;621H[WUHPHO\WKLQVPDOORXWOLQHSDFNDJHQROHDGV WHUPLQDOVERG\[[PP 627 E i / / H H H i $ $ ' ( WHUPLQDO LQGH[DUHD 'LPHQVLRQV 8QLW PP PP VFDOH $ $ E ' ( H / H / PD[ QRP PLQ 1RWH ,QFOXGLQJSODWLQJWKLFNQHVV 9LVLEOHGHSHQGLQJXSRQXVHGPDQXIDFWXULQJWHFKQRORJ\ VRWBSR 5HIHUHQFHV 2XWOLQH YHUVLRQ ,(& -('(& -(,7$ 627 (XURSHDQ SURMHFWLRQ ,VVXHGDWH Fig 17. Package outline SOT1202 (XSON6) 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 18 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 13. Abbreviations Table 15. Abbreviations Acronym Description CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model 14. Revision history Table 16. Revision history Document ID Release date Data sheet status Change notice Supersedes 74AXP1T125 v.1 20151221 Product data sheet - - 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 19 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state 15. Legal information 15.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nexperia.com. 15.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet. 15.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia's aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes -- Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. 74AXP1T125 Product data sheet Suitability for use -- Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of a Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the Nexperia product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). Nexperia does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 20 of 22 (c) Nexperia B.V. 2017. All rights reserved 74AXP1T125 Nexperia Dual supply buffer/line driver; 3-state Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia's warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia's specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia's standard warranty and Nexperia's product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 15.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com 74AXP1T125 Product data sheet All information provided in this document is subject to legal disclaimers. . Rev. 1 -- 21 December 2015 21 of 22 (c) Nexperia B.V. 2017. All rights reserved Nexperia 74AXP1T125 Dual supply buffer/line driver; 3-state 17. Contents 1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 11.1 12 13 14 15 15.1 15.2 15.3 15.4 16 17 (c) General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . . 7 Waveforms and graphs. . . . . . . . . . . . . . . . . . 11 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 19 Legal information. . . . . . . . . . . . . . . . . . . . . . . 20 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 20 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contact information. . . . . . . . . . . . . . . . . . . . . 21 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Nexperia B.V. 2017. All rights reserved For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 21 December 2015