50W Constant Power Mode LED Driver XLG-50 series IS 15885(Part 2/Sec13) THOMAS SAMUEL THOMAS SAMUEL R-41027766 (for XLG-50I type only) IP67 (except for XLG-50I type) Note.15 05 XLG- with the latest version of IEC61347/GB7000.1 -2015 and UL8750 international safety regulations. The output and dimming are also completely in accordance with the new regulations with isolation to ensure the userand luminaire system during installation. : File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series SPECIFICATION XLG-50 MODEL RATED CURRENT CONSTANT CURRENT REGION Note.2 OUTPUT RATED POWER VOLTAGE RANGE 90 ~ 305VAC 127 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) Note.4 FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< 10%(@load50%/115VC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section) EFFICIENCY (Typ.) 90% Note.10 0.57A / 115VAC 0.29A / 230VAC 0.24A/277VAC COLD START 50A(twidth=350s measured at 50% Ipeak) at 230VAC; Per NEMA 410 5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD / STANDBY POWER CONSUMPTION No load power consumption <0.5W for A, <0.75W for I series Standby power consumption <0.5W for AB-Type(Dimming OFF) OVER POWER 110-150% Over Power Protection, recovers automatically after fault condition is removed Constant current limiting, recovers automatically after fault condition is removed SHORT CIRCUIT OVER TEMPERATURE INPUT OVER VOLTAGE Note.8 Hiccup mode, recovers automatically after fault condition is removed 320 ~ 370VAC (Shut down output voltage when the input voltage exceeds protection voltage,recovers automatically after fault condition is removed) Can survive input voltage stress of 440Vac for 48 hours @ tc 75 max WORKING TEMP. Tcase=-40 ~ +90 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=+90 WORKING HUMIDITY 20 ~ 95% STORAGE TEMP. TEMP. COEFFICIENT -40 ~ +80 VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.8 UL8750(type"HL"), CSA C22.2 No. 250.13-12; ENEC AS/NZS IEC EN61347-1, AS/NZS EN61347-2-13 independent, EN62384;IP67; GB19510.1, GB19510.14, EAC TP TC 004,J61347-1(H29), J61347-2-13(H29),KC61347-1,KC61347-2-13,IS15885(Part2/Sec13)( for XLG-50I type only);NOM-058-SCFI-2017 approved SAFETY & WITHSTAND VOLTAGE EMC 0.53 ~ 2.1A 500ms, 100ms/115VAC, 230VAC MAX. No. of PSUs on 16A ENVIRONMENT 50W 5.0% max. @rated current 57V SETUP, RISE TIME Note.3 AC CURRENT INRUSH CURRENT(Typ.) PROTECTION 22 ~54V 100VAC ~ 305VAC CURRENT RIPPLE OPEN CIRCUIT VOLTAGE (max.) CURRENT ADJ. RANGE INPUT - 1A ISOLATION RESISTANCE 0.03%/ (0 ~ 60) I/P-O/P:3.75KVAC I/P-FG:2.0KVAC Parameter EMC EMISSION O/P-FG:1.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Conducted Radiated Standard EN55015(CISPR15) ,GB/T17743 Test Level/Note Harmonic Current EN61000-3-2 ,GB/T17625.1 --------Class C @load50% Voltage Flicker EN61000-3-3 ----- EN55015(CISPR15) ,GB/T17743 EN61547 EMC IMMUNITY OTHERS NOTE Parameter Standard Test Level/Note ESD EN61000-4-2 Level 3, 8KV air ; Level 2, 4KV contact Radiated EN61000-4-3 Level 3 EFT/Burst EN61000-4-4 Surge EN61000-4-5 Level 3 4KV/Line-Line 6KV/Line-Earth Conducted EN61000-4-6 Level 3 Magnetic Field EN61000-4-8 Level 4 Voltage Dips and Interruptions EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods 1252.69 K hrs min. Telcordia SR-332 (Bellcore) 394.57Khrs min. MIL-HDBK-217F (25) MTBF 105*63*30mm (L*W*H) DIMENSION 0.41Kg;24pcs/ 10.5Kg/0.68CUFT for A-type 0.42Kg;24pcs/ 11Kg/0.68CUFT for AB-type PACKING , https://www.meanwell.com/serviceDisclaimer.aspx File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS POWER SWITCHING PFC CIRCUIT RECTIFIERS & FILTER Vo+ VoO.L.P. O.T.P. DIM+ DIM- (AB Type) O.L.P. PWM & PFC CONTROL DETECTION CIRCUIT CASE :Protective Earth DRIVING METHODS OF LED MODULE 54V 1000mA,54V 530mA,54V 530mA, 50V 48V 42V 36V 30V 2100mA, 24V 24V 1050mA, 22V 18V 2100mA, 22V 12V 6V 0V 0mA 350mA 700mA 1050mA 1400mA 1750mA 2100mA 2450mA Recommend Performance Region File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series DIMMING OPERATION AC/N(Blue) AC/L(Brown) PE (Green/Yellow) V-(Black) V+(Red) XLG-50 DIM+( Blue ) DIM-(White) 3 in 1 dimming function (for AB-Type) Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.) Applying additive 0 ~ 10VDC 100% 90% Vo- + + - - DIM+ + Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive Voltage - 20% DIM- 10% 0% "DO NOT connect "DIM- to Vo-" 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): 100% 90% Vo- + + - - DIM+ Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive PWM signal 20% DIM- 10% 0% "DO NOT connect "DIM- to Vo-" 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Applying additive resistance: 100% 90% Vo- + 80% + - - DIM+ Additive Resistance Output current (%) Vo+ 70% 60% 50% 40% 30% DIM"DO NOT connect "DIM- to Vo-" 20% 10% 0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0k or 0Vdc, or 10V PWM signal with 0% duty cycle. File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series OUTPUT LOAD vs TEMPERATURE 100 80 80 230VAC input only 60 40 20 -40 -25 -10 0 15 30 230VAC input only 60 100VAC LOAD (%) LOAD (%) 100 230VAC 50 70 (HORIZONTAL) 60 40 20 -40 STATIC CHARACTERISTIC -25 0 20 45 55 65 75 90 (HORIZONTAL) POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 Constant Current Mode 100 1 90 0.95 0.9 80 0.85 0.8 PF LOAD (%) 70 60 277V50W 0.75 230V50W 0.7 115V50W 0.65 50 0.6 40 0.55 0.5 90 100 120 140 160 180 200 220 240 260 280 10% 305 20% 30% 40% INPUT VOLTAGE (V) 60Hz 60% 70% 80% 90% 100% LOAD De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD XLG-50 series possess superior working efficiency that up to 90% can be reached in field applications. 50V Model, Tcase at 75 50V Model, Tcase at 75 12 96 92 8 115VAC( 50W) 6 230VAC( 50W) 4 277VAC( 50W) EFFICIENCY(%) 10 THD(%) 50% 88 84 277V(50W) 80 230V(50W) 76 115V(50W) 72 68 2 64 0 50% 60% 70% 80% 90% 100% 60 50% LOAD 60% 70% 80% 90% LOAD File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series LIFE TIME LIFETIME(Kh) 120 100 80 60 40 20 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 Tcase ( ) File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series Mechanical Specification CASE NO.: 268A A-Type 105 99 90 tc 61.3 V-(Black) V+(Red) 31.6 SJOW 17AWGx3C &H05RN-F 3x1.0mm 2 SJOW 17AWGx2C 2 &05RN-F 1.0mm 4-4.5 : Max. Case Temperature 30 tc 25.8 9.9 AC/N(Blue) AC/L(Brown) PE (Green/Yellow) 63 30010 40 30010 Unit:mm File Name:XLG-50-SPEC 2020-12-17 XLG-50 50W Constant Power Mode LED Driver series AB-Type 105 99 90 AC/N(Blue) AC/L(Brown) PE (Green/Yellow) SJOW 17AWGx2C &05RN-F 1.0mm 2 V-(Black) V+(Red) 61.3 DIM+( Blue ) DIM-(White) 31.6 tc 63 30010 40 30010 SJOW 17AWGx3C &H05RN-F 3x1.0mm 2 UL2517 20AWGx2C 32510 4-4.5 : Max. Case Temperature 30 tc 9.9 25.8 Installation Manual Please refer to : http://www.meanwell.com/manual.html File Name:XLG-50-SPEC 2020-12-17