Previous Datasheet Index Next Data Sheet DISCRETE POWER DIODES and THYRISTORS DATA BOOK To Order Previous Datasheet Index Next Data Sheet Bulletin I25187/A ST333C..L SERIES INVERTER GRADE THYRISTORS Hockey Puk Version Features Metal case with ceramic insulator International standard case TO-200AC (B-PUK) 620A All diffused design Center amplifying gate Guaranteed high dV/dt Guaranteed high dI/dt High surge current capability Low thermal impedance High speed performance Typical Applications Inverters Choppers Induction heating case style TO-200AC (B-PUK) All types of force-commutated converters Major Ratings and Characteristics Parameters ST333C..L Units 620 A 55 C 1230 A 25 C @ 50Hz 11000 A @ 60Hz 11500 A @ 50Hz 605 KA2s @ 60Hz 553 KA2s 400 to 800 V 10 to 30 s - 40 to 125 C IT(AV) @ Ths IT(RMS) @ Ths ITSM I 2t V DRM /V RRM tq range TJ To Order Previous Datasheet ST333C..L Series Index Next Data Sheet ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , maximum VRSM , maximum I DRM /I RRM max. Code repetitive peak voltage non-repetitive peak voltage @ TJ = TJ max. V V mA 04 400 500 08 800 900 Type number ST333C..L 50 Current Carrying Capability ITM Frequency ITM ITM 180oel 180oel Units 100s 50Hz 400Hz 1430 1670 1250 1170 2340 2310 1940 2010 6310 3440 5620 5030 1000Hz 1080 880 2090 1800 2040 1750 2500Hz 530 400 1190 990 990 800 Recovery voltage Vr Voltage before turn-on Vd 50 50 50 50 50 Rise of on-state current di/dt 50 50 - - - - A/s Heatsink temperature 40 55 40 55 40 55 C Equivalent values for RC circuit 10 / 0.47F V DRM V DRM 50 V DRM 10 / 0.47F A V 10 / 0.47F On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature ST333C..L Units Conditions 620 (305) A 180 conduction, half sine wave 55 (75) C double side (single side) cooled I T(RMS) Max. RMS on-state current 1230 DC @ 25C heatsink temperature double side cooled I TSM Max. peak, one half cycle, 11000 t = 10ms No voltage non-repetitive surge current 11500 t = 8.3ms reapplied 9250 t = 10ms 100% VRRM 9700 t = 8.3ms reapplied Sinusoidal half wave, 605 t = 10ms No voltage Initial TJ = TJ max t = 8.3ms reapplied t = 10ms 100% VRRM t = 8.3ms reapplied I 2t Maximum I2t for fusing A 553 KA2s 428 391 I 2 t Maximum I2t for fusing 6050 KA2s To Order t = 0.1 to 10ms, no voltage reapplied Previous Datasheet ST333C..L Series Index Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics Fig. 6 - On-state Power Loss Characteristics Fig. 5 - On-state Power Loss Characteristics Fig. 7 - Maximum Non-repetitive Surge Current Next Data Sheet To Order Fig. 8 - Maximum Non-repetitive Surge Current Previous Datasheet Index Fig. 9 - On-state Voltage Drop Characteristics Fig. 11 - Reverse Recovered Charge Characteristics Next Data SheetSeries ST333C..L Fig. 10 - Thermal Impedance ZthJ-hs Characteristics Fig. 12 - Reverse Recovery Current Characteristics Fig 13 - Frequency Characteristics To Order Previous Datasheet ST333C..L Series Index Next Data Sheet Fig. 14 - Frequency Characteristics Fig. 15 - Frequency Characteristics Fig. 16 - Maximum On-state Energy Power Loss Characteristics To Order Previous Datasheet Index Next Data Sheet Series ST333C..L 10 Re c ta n g u la r g a t e p u lse a ) Re c o m m e n d e d lo a d lin e fo r ra t e d d i/ d t : 2 0 V , 1 0 o h m s; t r< = 1 s b ) Re c o m m e n d e d lo a d lin e fo r < = 3 0 % ra t e d d i/ d t : 1 0 V , 10 o h m s t r< = 1 s ( 1) ( 2) ( 3) ( 4) PG PG PG PG M M M M = = = = 10W , 20W , 4 0W , 60W , tp tp tp tp = = = = 20m s 10m s 5m s 3 .3 m s (a ) (b ) Tj= -40 C 1 Tj= 25 C Tj= 125 C In st a n t a n e o u s G a t e V o lt a g e ( V ) 10 0 ( 1) (2) (3 ) (4 ) VGD IG D D e v ic e : ST33 3 C ..L Se rie s Fre q u e n c y Lim ite d b y PG ( A V ) 0.1 0.0 01 0.01 0.1 1 In st a n ta n e o u s G a te C u rre n t ( A ) Fig. 17 - Gate Characteristics To Order 10 100 Previous Datasheet Index Next Data Sheet Series ST333C..L On-state Conduction Parameter V TM Max. peak on-state voltage V T(TO)1 Low level value of threshold voltage V T(TO)2 High level value of threshold voltage rt1 Low level value of forward slope resistance rt2 ST333C..L Units 1.96 0.91 ITM= 1810A, TJ = TJ max, tp = 10ms sine wave pulse V 0.58 m IH 600 IL Typical latching current 1000 (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max. 0.93 High level value of forward slope resistance Maximum holding current Conditions (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)), TJ = TJ max. 0.58 mA T J = 25C, I T > 30A T J = 25C, V A= 12V, Ra = 6, I G= 1A Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current td tq ST333C..L Units Conditions 1000 A/s TJ = TJ max, VDRM = rated VDRM Typical delay time Max. turn-off time TJ= 25C, VDM = rated VDRM, ITM = 50A DC, tp= 1s 1.1 Min 10 Max 30 ITM = 2 x di/dt s Resistive load, Gate pulse: 10V, 5 source TJ = TJ max, ITM = 550A, commutating di/dt = 40A/s VR = 50V, tp = 500s, dv/dt: see table in device code Blocking Parameter ST333C..L Units Conditions TJ = TJ max. linear to 80% VDRM, higher value available on request dv/dt Maximum critical rate of rise of off-state voltage 500 V/s IRRM IDRM Max. peak reverse and off-state leakage current 50 mA ST333C..L Units TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM Maximum peak gate power 60 PG(AV) Maximum average gate power 10 IGM Max. peak positive gate current 10 +VGM Maximum peak positive gate voltage 20 -VGM Maximum peak negative gate voltage IGT Max. DC gate current required to trigger VGT Max. DC gate voltage required to trigger Conditions W TJ = TJ max., f = 50Hz, d% = 50 A TJ = TJ max, tp 5ms V TJ = TJ max, tp 5ms 5 200 mA TJ = 25C, VA = 12V, Ra = 6 3 V IGD Max. DC gate current not to trigger 20 mA VGD Max. DC gate voltage not to trigger 0.25 V TJ = TJ max, rated VDRM applied To Order Previous Datasheet ST333C..L Series Index Next Data Sheet Thermal and Mechanical Specification Parameter ST333C..L TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJ-hs Max. thermal resistance, DC operation single side cooled K/W 0.05 RthC-hs Max. thermal resistance, wt C 0.11 junction to heatsink F Units Conditions 0.011 0.005 Mounting force, 10% 9800 N (1000) (Kg) 250 g Case style DC operation single side cooled K/W case to heatsink Approximate weight DC operation double side cooled DC operation double side cooled TO - 200AC (B-PUK) See Outline Table RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Single Side Double Side Units Conditions K/W TJ = TJ max. Single Side Double Side 180 0.012 0.010 0.008 0.008 120 0.014 0.015 0.014 0.014 90 0.018 0.018 0.019 0.019 60 0.026 0.027 0.027 0.028 30 0.045 0.046 0.046 0.046 Ordering Information Table Device Code ST 33 3 C 08 L H K 1 1 2 3 4 5 6 7 8 9 10 1 - Thyristor 2 - Essential part number 3 - 3 = Fast turn off 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - L = Puk Case TO-200AC (B-PUK) 7 - Reapplied dv/dt code (for tq test condition) 8 - tq code 9 - 0 = Eyelet term. (Gate and Aux. Cathode Unsoldered Leads) dv/dt - tq combinations available dv/dt (V/s) 20 50 100 200 400 10 12 15 18 20 25 30 CN CM CL CP CK --- DN DM DL DP DK --- EN EM EL EP EK --- -FM * FL * FP FK FJ -- --HL HP HK HJ HH 1 = Fast-on term. (Gate and Aux. Cathode Unsoldered Leads) tq (s) 2 = Eyelet term. (Gate and Aux. Cathode Soldered Leads) 3 = Fast-on term. (Gate and Aux. Cathode Soldered Leads) 10 - Critical dv/dt: None = 500V/sec (Standard value) L = 1000V/sec (Special selection) *Standard part number. All other types available only on request. To Order Previous Datasheet Index Next Data Sheet Series ST333C..L Outline Table 0.7 (0.03) MIN. 34 (1.34) DIA. MAX. 2 7 (1 .0 6 ) M AX . TWO PLACES PIN RECEPTACLE AMP. 60598-1 Case Style TO-200AC (B-PUK) 53 (2.09) DIA. MAX. 0.7 (0.03) MIN. All dimensions in millimeters (inches) 6.2 (0.24) MIN. 20 5 5 8 .5 (2 .3 ) D IA. M AX . 4.7 (0.18) 36.5 (1.44) 2 HOLES DIA. 3.5 (0.14) x 2.5 (0.1) DEEP CREPAGE DISTANCE 36.33 (1.430) MIN. STRIKE DISTANCE 17.43 (0.686) MIN. Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics To Order