JAC series(6-30A)
Three phase input type(1-stage filter)
JAC -30 -683 -O
Ordering information
1 Model Name
2 Rated Current
3 Line to ground capacitor code:See table 1.1.
table1.1 Line to ground capacitor code
Code Leakage Current
(Input 250/500V 60Hz)
Line to ground
capacitor
(nominal value)
103 0.5mA/1.0 mA max 10,000pF
223 1.0mA/2.0 mA max 22,000pF
683 2.5mA/5.0 mA max 68,000pF
*When the line to ground capacitor code is
different, the attenuation characteristic is
different.
*Please contact us about ultra high attenuation
type for EU (Wye type with neutral earth
system).
4 Option
D:DIN rail installation type
*
The dimensions change when the option is set.
Refer to External view.
H:Ultra high-attenuation type
1 2 3 4
Features of JAC series
Circuit Diagram Derating Curve
Compact and low profile , common mode EMI/EMC filters in 150kHz to 1MHz(1-
stage filter)
- Three Phase 500 VAC
- Push down type terminal block
R
Specifications
No. Items JAC-06-683 JAC-10-683 JAC-20-683 JAC-30-683
1Rated Voltage[V] AC Three Phase 500 (voltage range:528 max) 50/60Hz
2 Rated Current[A] 6 10 20 30
3 Test Voltage (Terminal-Mounting Plate) 2,500 VAC (Cutoff Current = 100mA), 1minute at room temperature and humidity
4 Isolation Resistance (Terminal-Mounting Plate) 500 VDC 100MW min at room temperature and humidity
5 Leakage current 250/500V 60Hz 2.5mA/5.0mA max
6 DC resistance 100mW max 45mW max 15mW max 8mW max
7 Safety agency approval temperatures -25 to +85C (Refer to Derating Curve)
8 Operating temperature -40 to +85C (Refer to Derating Curve)
9 Operating humidity 20 to 95%RH (Non condensing)
10 Storage temperature/humidity -40 to +85C/20 to 95%RH (Non condensing)
11 Vibration 10 to 55Hz, 19.6m/s2 (2G), 3min. Period, 1hour each X, Y and Z axis
12 Impact 196.1m/s2 (20G), 11ms Once each X, Y and Z axis
13 Safety agency approvals UL1283, CSA C22.2 No.8 (C-UL) , DIN EN60939 VDE0565 Teil3-1, ENEC
14 Case size (without projection) 63X44X132 mm (WXHXD) (Option: -D refer to external view)
[2.48X1.73X5.20 inches] (WXHXD)
15 Weight 440g max
Case
LI
NE
1
2
3
LOAD
4
5
6
CY
CXCXCXCXCXCX
CY
: Mounting Plate
CY : Line to ground
capacitor
CX : Line to line
capacitor
70 80 90-20 40 50 60
20
10
0
-40 -30
100
80
70
60
40
Ambient Temperature [ ]
Load Factor [%]
DIN rail installation type is optionThe terminal cover is retracted inside the unit
JAC-1
JAC series(6-30A)
External view
Standard Type
DIN rail installation Type
3-M4
Output
Terminal
[2.48]
[1.97]
[0.38]
Protection Earth
M4
[4.61]
Mounting Plate
[0.52]
Input
Terminal
3-M4
Mounting Hole
2-f5.5
[5.20]
[4.69]
[0.22]
(Terminal Block screw pitch)
(Mounting Hole pitch)
132
119
118
9.7
50
63
13.3
¶
Close the terminal cover
Terminal cover
[1.26]
Terminal Cover
[0.10]
[0.08]
[0.31]
[1.73]
¶ Tolerance : ±1[±0.04]
¶ Weight : 440g max
¶ Mounting Plate : Iron(surface finishing : nickel plating) t=1.0[0.04]
¶ Case : PBT
¶ Dimensions in mm, [ ]=inches
¶ Terminal block screw tighting torque M4 : 1.6N-m(16.9kgf-cm)max
32
2.5
44
8
2
Name Plate
Terminal cover
¶
Close the terminal cover
3-M4
Input
Terminal
[0.52]
13.3
Name Plate
Mounting Plate
DIN rail
(9)
M4
Protection Earth
[0.38]
[2.48]
Output
Terminal
3-M4
63
9.7
¶ Tolerance : ±1[±0.04]
¶ Weight : 440g max
¶ Mounting Plate : Iron(surface finishing : nickel plating) t=1.0[0.04]
¶ Case : PBT
¶ Dimensions in mm, [ ]=inches
¶ Terminal block screw tighting torque M4 : 1.6N-m(16.9kgf-cm)max
[0.31]
[1.73]
[0.28] [0.08]
8
72
44
Terminal Cover
[1.26][0.10]
2.5 32
DIN rail
[0.35]
[4.69]
[5.20]
Name Plate
(Terminal Block screw pitch)
119
132 9
±2
4.5 4.5
4.5 4.5
[0.18]
[0.18] [0.18]
[0.18]
As this product is adopted push-down type terminal block, this appearance is as follows.
1The terminal cover is retracted inside the unit.
2The screws for connecting the terminals are held in the up right position.
¡Note when installing the EMI/
EMC Filter on a DIN rail.
When the EMI/EMC Filter is grounded through
the DIN rail, the proper noise attenuation may not
be achieved.
Be sure to connect the protection earth (PE) of
the EMI/EMC Filter body to the earth.
JAC-2
