[AK4438]
016001925-E-00 2016/03
- 1 -
1. General Description
The AK4438 is an 8-channel 32-bit DAC which corresponds to digital audio systems. An internal circuit
includes newly developed 32-bit Digital Filter achieving short group delay and high quality sound. It
corresponds to a 768kHz PCM input at maximum, suitable for play backing high resolution audio sources
that are becoming widespread in network audios, USB-DACs and Car Audio Systems. In addition,
“OSR-Doubler” technology is newly adopted, making the AK4438 capable of supporting wide range
signals and achieving low out-of-band noise while realizing low power consumption. Moreover, the
AK4438 has five types of 32-bit digital filters, realizing simple and flexible sound making in wide range of
applications.
Application: AV Receivers, CD/SACD Players, Network Audios, USB DACs, USB Headphones, Sound
Plate/Bars, Car Audios, Automotive External Amplifiers, Measuring Instruments and Control
Systems.
2. Features
1. 8ch 32bit DAC
- 256 x Over sampling
- 32-bit High Quality Sound Short Delay Digital Filter
- Single-ended Output, Smoothing Filter
- THD+N: 91dB
- DR, S/N: 108dB
- Channel Independent Digital Volume Control (0dB～-127dB, 0.5dB Step, Mute)
- Soft Mute
- De-emphasis Filter (supporting 32kHz, 44.1kHz and 48kHz)
- I/F Format: MSB justified, LSB justified, I2S, TDM
- Zero Detection
2. Sampling Frequency
- Normal Speed Mode: 8kHz to 48kHz
- Double Speed Mode: 48kHz to 96kHz
- Quad Speed Mode: 96kHz to 192kHz
- Oct Speed Mode: 384kHz
- Hex Speed Mode: 768kHz
3. Master Clock
256fs, 384fs or 512fs, 768fs (Normal Speed Mode: fs=8kHz 48kHz)
256fs, 384fs (Double Speed Mode: fs=48kHz 96kHz)
128fs, 192fs (Quad Speed Mode: fs=96kHz 192kHz)
64fs, 96fs (Oct Speed Mode: fs=384kHz)
32fs, 48fs (Hex Speed Mode: fs=768kHz)
4. P Interface: 3-wire Serial/ I2C bus (Ver 1.0, 400kHz mode)
5. Power Supply
- Analog Supply: AVDD = 3.0 3.6V
- In/Output Buffer: TVDD = 1.7 3.6V
- Integrated LDO for Digital Power Supply
8. Power Consumption: 31mA (fs=48kHz)
9. Operating Temperature: Ta = - 40 105℃
10. Package: 32-pin QFN(0.5mm pitch)
108dB 768kHz 32bit 8-Channel Audio DAC
AK4438
[AK4438]
016001925-E-00 2016/03
- 2 -
3. Table of Contents
1. General Description ............................................................................................................................. 1
2. Features............................................................................................................................................... 1
3. Table of Contents ................................................................................................................................ 2
4. Block Diagram and Functions ............................................................................................................. 3
5. Pin Configurations and Functions ....................................................................................................... 4
■ Pin Configurations .............................................................................................................................. 4
■ Pin Functions ...................................................................................................................................... 5
■ Handling of Unused Pin ..................................................................................................................... 6
6. Absolute Maximum Ratings................................................................................................................. 7
7. Recommended Operation Conditions ................................................................................................. 7
8. Electrical Characteristics ..................................................................................................................... 8
9. Filter Characteristics (fs=48kHz) ......................................................................................................... 9
■ Sharp Roll-Off Filter (SD bit = “0”, SLOW bit = “0”) ........................................................................... 9
■ Slow Roll-Off Filter (SD bit = “0”, SLOW bit = “1”) .......................................................................... 10
■ Short Delay Sharp Roll-Off Filter (SD bit = “1”, SLOW bit = “0”) ..................................................... 11
■ Short Delay Slow Roll-Off Filter (SD bit = “1”, SLOW bit = “1”) ....................................................... 12
10. DC Characteristics ......................................................................................................................... 13
11. Switching Characteristics ............................................................................................................... 14
■ Timing Diagram ................................................................................................................................ 17
12. Functional Descriptions .................................................................................................................. 21
■ System Clock ................................................................................................................................... 21
■ De-emphasis Filter ........................................................................................................................... 24
■ Audio Interface Format ..................................................................................................................... 25
■ Digital Filter ...................................................................................................................................... 34
■ Zero Detection .................................................................................................................................. 34
■ Digital Volume Function ................................................................................................................... 35
■ LR Channel Output Signal Select .................................................................................................... 36
■ Soft Mute Operation ......................................................................................................................... 38
■ Error Detection ................................................................................................................................. 39
■ System Reset ................................................................................................................................... 39
■ Power Down Function ...................................................................................................................... 40
■ Power Off and Reset Functions ....................................................................................................... 41
■ Clock Synchronization ..................................................................................................................... 45
■ Parallel Mode ................................................................................................................................... 47
■ Audio Interface ................................................................................................................................. 47
■ Soft Mute .......................................................................................................................................... 47
■ Serial Control Interface .................................................................................................................... 48
■ Register Map .................................................................................................................................... 52
■ Register Definitions .......................................................................................................................... 53
13. Recommended External Circuits ................................................................................................... 58
■ Typical Connection Diagram ............................................................................................................ 58
14. Package ......................................................................................................................................... 61
■ Outline Dimensions .......................................................................................................................... 61
■ Material & Lead Finish ..................................................................................................................... 61
■ Marking ............................................................................................................................................. 62
15. Ordering Guide............................................................................................................................... 62
■ Ordering Guide ................................................................................................................................. 62
16. Revision History ............................................................................................................................. 62
IMPORTANT NOTICE ............................................................................................................................ 63
[AK4438]
016001925-E-00 2016/03
- 3 -
4. Block Diagram and Functions
LRCK
BICK
SDTI1
SDTI2
MCLK
PDN
SDTI3
DATT
Soft Mute
SDTI4
uP I/F
(I2C/SPI)
SCL/CCLK/TDM1
SDA/CDTI/TDM0
CAD0_I2C/CSN/DIF
I2C
SMUTE/CAD1
VREFH
VREFL
SCF
AOUTL1
SCF
AOUTR1
SCF
AOUTL2
SCF
AOUTR2
SCF
AOUTL3
SCF
AOUTR3
SCF
AOUTL4
SCF
AOUTR4
SMF
SMF
SMF
SMF
SMF
SMF
SMF
SMF
VSS1
TVDD
LDOO
LDO
DZF
AVDD
VSS2
PS/CAD0_SPI
VCOM
TEST
Audio
I/F
MCLK
LRCK
BICK
SDIN1
SDIN2
SDIN3
SDIN4
DATT
Soft Mute
DATT
Soft Mute
DATT
Soft Mute
8X
Interpolator
Modulator
Modulator
Modulator
Modulator
8X
Interpolator
8X
Interpolator
8X
Interpolator
Figure 1. Block Diagram
[AK4438]
016001925-E-00 2016/03
- 4 -
5. Pin Configurations and Functions
■ Pin Configurations
VSS1
25
26
AOUTR4
27
TEST
28
29
I2C
30
TVDD
LDOO
24
23
22
21
20
19
1
LRCK
2
SDTI1
3
SDTI2
4
SDTI3
5
6
14
13
12
11
10
9
SMUTE / CAD1
SDA/ CDTI /TDM0
CAD0_I2C/CSN/DIF
SCL/ CCLK/TDM1
AOUTL1
PS/CAD0_SPI
PDN
Top View
AOUTR3
AOUTL4
AOUTR1
31
32
7
8
16
15
18
17
SDTI4
DZF
MCLK
BICK
AOUTL3
AVDD
VSS2
VCOM
VREFL
VREFH
AOUTR2
AOUTL2
Back TAB:Note
Figure 2. Pin Configurations
Note: The exposed pad on the bottom surface of the package must be open or connected to the analog
ground.
[AK4438]
016001925-E-00 2016/03
- 5 -
■ Pin Functions
No.
Pin Name
I/O
PD state
Function
1
MCLK
I
Hi-z
External Master Clock Input Pin
2
BICK
I
Hi-z
Audio Serial Data Clock Pin
3
LRCK
I
Hi-z
Input Channel Clock Pin
4
SDTI1
I
Hi-z
Audio Serial Data Input
5
SDTI2
I
Hi-z
Audio Serial Data Input
6
SDTI3
I
Hi-z
Audio Serial Data Input
7
SDTI4
I
Hi-z
Audio Serial Data Input
8
DZF
O
50kΩ
Pull-down
Zero Input Detect in I2C Bus or 3-wire serial control mode
9
PDN
I
Hi-z
Power-Down & Reset Pin.
When “L”, the AK4438 is powered-down and the control registers are reset to
default state.
10
SMUTE
I
Hi-z
Soft Mute Pin in Parallel control mode.
When this pin is changed to “H”, soft mute cycle is initiated. When returning
“L”, the output mute releases.
CAD1
I
Chip Address 1 Pin in I2C Bus or 3-wire serial control mode
11
SDA
I/O
Hi-z
Control Data Input Pin in I2C Bus serial control mode
CDTI
I
Control Data Input Pin in 3-wire serial control mode
TDM0
I
TDM Mode select pin in Parallel control mode.
12
SCL
I
Hi-z
Control Data Clock Pin in I2C Bus serial control mode
CCLK
I
Control Data Clock Pin in 3-wire serial control mode
TDM1
I
TDM Mode select pin in Parallel control mode.
13
CAD0_I2C
I
Hi-z
Chip Address 0 Pin in I2C Bus serial control mode
CSN
I
Chip Select Pin in 3-wire serial control mode
DIF
I
Audio Data Format Select in Parallel control mode.
“L”: 32bit MSB, “H”: 32bit I2S
14
PS
I
Hi-z
(I2C pin = “H”) Control Mode Select Pin
“L”: I2C Bus serial control mode, “H”: Parallel control mode.
CAD0_SPI
I
(I2C pin = “L”) Chip Address 0 Pin in 3-wire serial control mode
15
AOUTL1
O
Hi-z
Lch Analog Output Pin
16
AOUTR1
O
Hi-z
Rch Analog Output Pin
17
AOUTL2
O
Hi-z
Lch Analog Output Pin
18
AOUTR2
O
Hi-z
Rch Analog Output Pin
19
VREFH
-
Hi-z
Positive Voltage Reference Input Pin, AVDD
20
VREFL
-
Hi-z
Negative Voltage Reference Input Pin, VSS2
21
VCOM
O
500Ω
Pull-down
Common Voltage Output Pin, AVDDx1/2
Large external capacitor around 2.2µF is used to reduce power-supply noise.
22
VSS2
-
-
Analog Ground Pin
23
AVDD
-
-
Analog Power Supply Pin, 3.0V3.6V
24
AOUTL3
O
Hi-z
Lch Analog Output Pin
25
AOUTR3
O
Hi-z
Rch Analog Output Pin
26
AOUTL4
O
Hi-z
Lch Analog Output Pin
27
AOUTR4
O
Hi-z
Rch Analog Output Pin
28
TEST
-
25kΩ
Pull-down
This pin must be connected to VSS1.
29
I2C
I
Hi-z
Control Mode Select Pin
“L”: 3-wire serial control mode
“H”: I2C Bus serial control mode or Parallel control mode.
30
TVDD
-
-
Digital Power Supply Pin, 1.7V3.6V
31
VSS1
-
-
Digital Ground Pin
32
LDOO
O
580Ω
Pull-down
LDO Output Pin.
This pin must be connected to ground with 2.2uF ±50%.
Note 1. All digital input pins must not be allowed to float.
[AK4438]
016001925-E-00 2016/03
- 6 -
■ Handling of Unused Pin
Unused I/O pins must be connected appropriately.
Classification
Pin Name
Setting
Analog
AOUTL1-4, AOUTR1-4
Open
Digital
DZF
Open
SDTI1-4
Connect to VSS1
[AK4438]
016001925-E-00 2016/03
- 7 -
6. Absolute Maximum Ratings
(VSS1=VSS2=0V; Note 2)
Parameter
Symbol
Min.
Max.
Unit
Power Supplies
Analog
Digital
Difference (VSS1 ~ 2)
AVDD
TVDD
ΔGND
-0.3
-0.3
-0.3
4.3
4.3
0.3
V
V
V
Input Current (any pins except for supplies)
IIN
-
10
mA
Digital Input Voltage
VIND
-0.3
TVDD+0.3
V
Ambient Temperature (power applied)
Ta
-40
105
C
Storage Temperature
Tstg
-65
150
C
Note 2. All voltages with respect to ground. VSS1 and VSS2 must be connected to the same analog
ground plane.
Note 3. The maximum Digital input voltage is smaller value between (LVDD+0.3)V and 4.3V.
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
7. Recommended Operation Conditions
(VSS1=VSS2=0V; Note 2)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Power Supplies
Analog
Digital
AVDD
TVDD
3.0
1.7
3.3
3.3
3.6
3.6
V
V
Voltage Reference
(Note 5)
“H” voltage reference
“L” voltage reference
VREFH
VREFL
AVDD0.5
-
-
VSS2
AVDD
-
V
V
Note 4. The power up sequence between AVDD and TVDD is not critical.
Note 5. The VREFL pin must be connected to VSS2.
Note 6. Do not turn off the power supply of the AK4438 with the power supply of the peripheral device
turned on. When using the I2C interface, pull-up resistors of SDA and SCL pins should be
connected to TVDD or less voltage.
* AKM assumes no responsibility for the usage beyond the conditions in this data sheet.
[AK4438]
016001925-E-00 2016/03
- 8 -
8. Electrical Characteristics
(Ta=25C; AVDD =TVDD=3.3V; VSS1=VSS2 =0V; VREFH=AVDD; fs=48kHz; BICK=64fs; Signal
Frequency=1kHz; 32bit Data; Measurement Frequency=20Hz20kHz at 48kHz, 20Hz~40kHz at
fs=96kHz, 20Hz~40kHz at fs=192kHz, unless otherwise specified.)
Parameter
Min.
Typ.
Max.
Unit
DAC Analog Output Characteristics
Resolution
32
bit
Output Voltage (Note 7)
2.55
2.83
3.11
Vpp
S/(N+D)
(0dBFS)
fs=48kHz
80
91
dB
fs=96kHz
-
89
dB
fs=192kHz
-
89
dB
Dynamic Range
(-60dBFS)
fs=48kHz (A-weighted)
104
108
dB
fs=96kHz
-
101
dB
fs=192kHz
-
101
dB
S/N
fs=48kHz (A-weighted)
104
108
dB
fs=96kHz
-
101
dB
fs=192kHz
-
101
dB
Interchannel Isolation
90
110
dB
Interchannel Gain Mismatch
0
0.7
dB
Load Resistance (Note 8)
10
k
Load Capacitance
30
pF
Power Supply Rejection (Note 9)
-
50
-
dB
Note 7. Full-scale output voltage. The output voltage is always proportional to AVDD (AVDD x 0.86).
Note 8. AC Load
Note 9. This is a value when applying a 1kHz 50mVpp sine wave to AVDD.
Parameter
Min.
Typ.
Max.
Unit
Power Supplies
Power Supply Current
Normal Operation (PDN pin = “H”)
AVDD fs=48kHz, 96kHz, 192kHz
TVDD fs=48kHz
TVDD fs=96kHz
TVDD fs=192kHz
Power-down mode
(PDN pin = “L”) (Note 10)
AVDD+TVDD
27
3.4
4.9
8.0
10
36
4.5
6.4
10.4
200
mA
mA
mA
mA
µA
Note 10. Quiescent Current. All digital input pins including clock pins are fixed to VSS.
[AK4438]
016001925-E-00 2016/03
- 9 -
9. Filter Characteristics (fs=48kHz)
(Ta= -40 +105C; AVDD =3.0 3.6V, TVDD=1.7 3.6V; DEM=OFF)
■ Sharp Roll-Off Filter (SD bit = “0”, SLOW bit = “0”)
fs=44.1kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
20.0
kHz
3.0dB
PB
21.5
kHz
Passband Ripple (Note 12)
PR
-0.0032
0.0032
dB
Stopband (Note 11)
SB
24.1
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
26.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-0.26
0.1
dB
fs=96kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
43.5
kHz
3.0dB
PB
46.8
kHz
Passband Ripple (Note 12)
PR
-0.0032
0.0032
dB
Stopband (Note 11)
SB
52.5
0
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
26.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-0.53
0.1
dB
fs=192kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
87.0
kHz
3.0dB
PB
93.6
kHz
Passband Ripple (Note 12)
PR
-0.0032
0.0032
dB
Stopband (Note 11)
SB
105
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
26.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-1.9
0.1
dB
Note 11. The pass band and stop band frequencies scale with fs. For example, PB=0.4535×fs,
SB=0.546×fs.
Note 12. It is the pass band gain amplitude of the double over sampling filter at the first step of the
Interpolator.
Note 13. The calculating delay time which occurred by digital filtering. This time is from setting the
16/20/24/32bit data of both channels to input register to the output of analog signal.
Note 14. The output level is assumed as 0dB when inputting a 1kHz 0dB sine wave.
*Digital filter characteristics are based on simulation results.
[AK4438]
016001925-E-00 2016/03
- 10 -
■ Slow Roll-Off Filter (SD bit = “0”, SLOW bit = “1”)
fs=44.1kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 15)
0.05dB
PB
0
8.1
kHz
3.0dB
PB
18.2
kHz
Passband Ripple (Note 12)
PR
-0.043
0.0032
dB
Stopband (Note 15)
SB
39.2
kHz
Stopband Attenuation (Note 14)
SA
73
dB
Group Delay (Note 13)
GD
-
6.3
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.06
0.1
dB
fs=96kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 15)
0.05dB
PB
0
17.7
kHz
3.0dB
PB
39.5
kHz
Passband Ripple (Note 12)
PR
-0.043
0.043
dB
Stopband (Note 15)
SB
85.3
kHz
Stopband Attenuation (Note 14)
SA
73
dB
Group Delay (Note 13)
GD
-
6.3
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.23
0.1
dB
fs=192kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 15)
0.05dB
PB
0
35.5
kHz
3.0dB
PB
79.0
kHz
Passband Ripple (Note 12)
PR
-0.043
0.043
dB
Stopband (Note 15)
SB
171
kHz
Stopband Attenuation (Note 14)
SA
73
dB
Group Delay (Note 13)
GD
-
6.3
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.90
0.1
dB
Note 15. The pass band and stop band frequencies scale with fs. For example, PB=0.185×fs,
SB=0.888×fs.
[AK4438]
016001925-E-00 2016/03
- 11 -
■ Short Delay Sharp Roll-Off Filter (SD bit = “1”, SLOW bit = “0”)
fs=44.1kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
20.0
kHz
3.0dB
PB
21.5
kHz
Passband Ripple (Note 12)
PR
-0.0031
0.0031
dB
Stopband (Note 11)
SB
24.1
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
5.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-0.26
0.1
dB
fs=96kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
43.5
kHz
3.0dB
PB
46.8
kHz
Passband Ripple (Note 12)
PR
-0.0031
0.0031
dB
Stopband (Note 11)
SB
52.5
0
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
5.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-0.53
0.1
dB
fs=192kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 11)
0.05dB
PB
0
87.0
kHz
3.0dB
PB
93.6
kHz
Passband Ripple (Note 12)
PR
-0.0031
0.0031
dB
Stopband (Note 11)
SB
105
kHz
Stopband Attenuation (Note 14)
SA
80
dB
Group Delay (Note 13)
GD
-
5.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-1.9
0.1
dB
[AK4438]
016001925-E-00 2016/03
- 12 -
■ Short Delay Slow Roll-Off Filter (SD bit = “1”, SLOW bit = “1”)
fs=44.1kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 16)
0.05dB
PB
0
11.1
kHz
3.0dB
PB
19.4
kHz
Passband Ripple (Note 12)
PR
-0.05
0.05
dB
Stopband (Note 16)
SB
38.1
kHz
Stopband Attenuation (Note 14)
SA
82
dB
Group Delay (Note 13)
GD
-
4.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.06
0.1
dB
fs=96kHz
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 16)
0.05dB
PB
0
24.2
kHz
3.0dB
PB
42.1
kHz
Passband Ripple (Note 12)
PR
-0.05
0.05
dB
Stopband (Note 16)
SB
83.0
kHz
Stopband Attenuation (Note 14)
SA
82
dB
Group Delay (Note 13)
GD
-
4.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.23
0.1
dB
fs=192kH
Parameter
Symbol
Min.
Typ.
Max.
Unit
Digital Filter
Passband (Note 16)
0.05dB
PB
0
48.4
kHz
3.0dB
PB
84.3
kHz
Passband Ripple (Note 12)
PR
-0.05
0.05
dB
Stopband (Note 16)
SB
165.9
kHz
Stopband Attenuation (Note 14)
SA
82
dB
Group Delay (Note 13)
GD
-
4.8
-
1/fs
Digital Filter + SCF + SMF (Note 14)
Frequency Response : 0 20.0kHz
-5.90
0.1
dB
Note 16. The pass band and stop band frequencies scale with fs. For example, PB=0.252×fs,
SB=0.864×fs.
[AK4438]
016001925-E-00 2016/03
- 13 -
10. DC Characteristics
(Ta= -40 +105C; AVDD =3.0 3.6V, TVDD=1.7 3.6V)
Parameter
Symbol
Min.
Typ.
Max.
Unit
TVDD=1.7V 3.0V
High-Level Input Voltage
Low-Level Input Voltage
VIH1
VIL1
80%TVDD
-
-
-
-
20%TVDD
V
V
TVDD=3.0V 3.6V
High-Level Input Voltage
Low-Level Input Voltage
VIH2
VIL2
70%TVDD
-
-
-
-
30%TVDD
V
V
High-Level Output Voltage
(DZF pins: Iout= -100µA)
Low-Level Output Voltage
(DZF pin : Iout= 100µA)
(SDA pin, 2.0V TVDD 3.6V: Iout= 3mA)
(SDA pin, 1.7V TVDD 2.0V: Iout= 3mA)
VOH
VOL1
VOL2
VOL3
TVDD0.5
-
-
-
-
-
-
-
0.5
0.4
20%TVDD
V
V
V
V
Input Leakage Current
Iin
-
-
10
A
[AK4438]
016001925-E-00 2016/03
- 14 -
11. Switching Characteristics
(Ta=-40 105C; AVDD=3.0 3.6V, TVDD=1.7 3.6V; CL=20pF, unless otherwise specified.)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Master Clock Timing
External Clock
256fsn:
Pulse Width Low
Pulse Width High
384fsn:
Pulse Width Low
Pulse Width High
512fsn, 256fsd, 128fsq, 64fso, 32fsh:
Pulse Width Low
Pulse Width High
768fsn, 384fsd, 192fsq, 96fso, 48fsh:
Pulse Width Low
Pulse Width High
fCLK
tCLKL
tCLKH
fCLK
tCLKL
tCLKH
fCLK
tCLKL
tCLKH
fCLK
tCLKL
tCLKH
2.048
32
32
3.072
22
22
4.096
16
16
6.144
11
11
12.288
18.432
24.576
36.864
MHz
ns
ns
MHz
ns
ns
MHz
ns
ns
MHz
ns
ns
LRCK Timing (Slave mode)
Stereo mode
(TDM1-0 bits = “00”)
Normal Speed Mode
Double Speed Mode
Quad Speed Mode
Oct speed mode
Hex speed mode
Duty Cycle
fsn
fsd
fsq
fso
fsh
Duty
8
48
96
45
384
768
48
96
192
55
kHz
kHz
kHz
kHz
kHz
%
TDM128 mode
(TDM1-0 bits = “01”)
LRCK frequency
“H” time
“L” time
fsn
fsd
fsq
tLRH
tLRL
8
48
96
1/128fs
1/128fs
48
96
192
kHz
kHz
kHz
ns
ns
TDM256 mode
(TDM1-0 bits = “10”)
LRCK frequency
“H” time
“L” time
fsn
fsd
tLRH
tLRL
8
48
1/256fs
1/256fs
48
96
kHz
kHz
ns
ns
TDM512 mode
(TDM1-0 bits = “11”)
LRCK frequency
“H” time
“L” time
fsn
tLRH
tLRL
8
1/512fs
1/512fs
48
kHz
ns
ns
[AK4438]
016001925-E-00 2016/03
- 15 -
Parameter
Symbol
Min.
Typ.
Max.
Unit
Audio Interface Timing
Stereo mode (TDM1-0 bits = “00”)
BICK Period
Normal Speed Mode
Double Speed Mode
Quad Speed Mode
Oct Speed Mode
Hex Speed Mode
BICK Pulse Width Low
BICK Pulse Width High
LRCK Edge to BICK “” (Note 17)
BICK “” to LRCK Edge (Note 17)
SDTI Hold Time
SDTI Setup Time
tBCK
tBCK
tBCK
tBCK
tBCK
tBCKL
tBCKH
tLRB
tBLR
tSDH
tSDS
1/256fsn
1/128fsd
1/64fsq
1/64fso
1/64fsh
9
9
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
TDM128 mode (TDM1-0 bits = “01”)
BICK Period
Normal Speed Mode
Double Speed Mode
Quad Speed Mode
BICK Pulse Width Low
BICK Pulse Width High
LRCK Edge to BICK “” (Note 17)
BICK “” to LRCK Edge (Note 17)
SDTI Hold Time
SDTI Setup Time
tBCK
tBCK
tBCK
tBCKL
tBCKH
tBLR
tLRB
tSDH
tSDS
1/128fsn
1/128fsd
1/128fsq
16
16
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
TDM256 mode (TDM1-0 bits = “10”)
BICK Period
Normal Speed Mode
Double Speed Mode
BICK Pulse Width Low
BICK Pulse Width High
LRCK Edge to BICK “” (Note 17)
BICK “” to LRCK Edge (Note 17)
SDTI Hold Time
SDTI Setup Time
tBCK
tBCK
tBCKL
tBCKH
tBLR
tLRB
tSDH
tSDS
1/256fsn
1/256fsd
16
16
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
ns
TDM512 mode (TDM1-0 bits = “11”)
BICK Period
Normal Speed Mode
BICK Pulse Width Low
BICK Pulse Width High
LRCK Edge to BICK “” (Note 17)
BICK “” to LRCK Edge (Note 17)
SDTI Hold Time
SDTI Setup Time
tBCK
tBCKL
tBCKH
tBLR
tLRB
tSDH
tSDS
1/512fsn
16
16
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
Note 17. BICK rising edge must not occur at the same time as LRCK edge.
[AK4438]
016001925-E-00 2016/03
- 16 -
Parameter
Symbol
Min.
Typ.
Max.
Unit
Control Interface Timing (3-wire Serial mode):
CCLK Period
CCLK Pulse Width Low
Pulse Width High
CDTI Setup Time
CDTI Hold Time
CSN “H” Time
CSN “” to CCLK “”
CCLK “” to CSN “”
tCCK
tCCKL
tCCKH
tCDS
tCDH
tCSW
tCSS
tCSH
200
80
80
40
40
150
50
50
ns
ns
ns
ns
ns
ns
ns
ns
Control Interface Timing (I2C Bus mode):
SCL Clock Frequency
Bus Free Time Between Transmissions
Start Condition Hold Time (prior to first clock pulse)
Clock Low Time
Clock High Time
Setup Time for Repeated Start Condition
SDA Hold Time from SCL Falling (Note 18)
SDA Setup Time from SCL Rising
Rise Time of Both SDA and SCL Lines
Fall Time of Both SDA and SCL Lines
Setup Time for Stop Condition
Pulse Width of Spike Noise Suppressed by Input Filter
Capacitive load on bus
fSCL
tBUF
tHD:STA
tLOW
tHIGH
tSU:STA
tHD:DAT
tSU:DAT
tR
tF
tSU:STO
tSP
Cb
-
1.3
0.6
1.3
0.6
0.6
0
0.1
-
-
0.6
0
-
400
-
-
-
-
-
-
-
1.0
0.3
-
50
400
kHz
s
s
s
s
s
s
s
s
s
ns
pF
Power-down & Reset Timing
PDN Pulse Width (Note 19)
PDN Reject Pulse Width
tAPD
tRPD
800
50
ns
ns
Note 18. Data must be held for sufficient time to bridge the 300 ns transition time of SCL.
Note 19. The AK4438 can be reset by setting the PDN pin to “L” upon power-up. The PDN pin must held
“L” for more than 800ns for a certain reset. The AK4438 is not reset by the “L” pulse less than
50ns.
Note 20. I2C-bus is a trademark of NXP B.V.
[AK4438]
016001925-E-00 2016/03
- 17 -
■ Timing Diagram
1/fCLK
tCLKL
VIH
tCLKH
MCLK
VIL
1/fsn, 1/fsd, 1/fsq
LRCK
VIH
VIL
tBCK
tBCKL
VIH
tBCKH
BICK
VIL
tdLRKL
tdLRKH
Duty
= tdLRKH (or tdLRKL) x fs x 100
Figure 3. Clock Timing (TDM1-0 bits = “00”)
1/fCLK
tCLKL
VIH
tCLKH
MCLK
VIL
1/fs
LRCK
VIH
VIL
tLRL
tLRH
tBCK
tBCKL
VIH
tBCKH
BICK
VIL
Figure 4. Clock Timing (Except TDM1-0 bits = “00”)
[AK4438]
016001925-E-00 2016/03
- 18 -
tLRB
LRCK
VIH
BICK
VIL
VIH
VIL
tBLR
tSDS
SDTI
VIH
VIL
tSDH
Figure 5. Audio Interface Timing (TDM1-0 bits = “00”)
tLRB
LRCK
VIH
BICK
VIL
VIH
VIL
tBLR
tSDS
SDTI
VIH
VIL
tSDH
Figure 6. Audio Interface Timing (Except TDM1-0 bits = “00”)
[AK4438]
016001925-E-00 2016/03
- 19 -
CSN VIH
VIL
tCSS
CCLK
tCDS
VIH
VIL
CDTI VIH
tCCKHtCCKL
tCDH
VIL
C1 C0 R/W
tCSH
Figure 7. WRITE Command Input Timing (3-wire Serial mode)
CSN VIH
VIL
tCSH
CCLK VIH
VIL
CDTI VIH
tCSW
VIL
D1 D0D2
tCSS
Figure 8. WRITE Data Input Timing (3-wire Serial mode)
[AK4438]
016001925-E-00 2016/03
- 20 -
tHIGH
SCL
SDA
VIH
tLOW
tBUF
tHD:STA
tR
tF
tHD:DAT
tSU:DAT
tSU:STA
Stop
Start
Start
Stop
tSU:STO
VIL
VIH
VIL
tSP
Figure 9. I2C Bus mode Timing
tAPD
PDN VIL
tRPD
Figure 10. Power-down & Reset Timing
[AK4438]
016001925-E-00 2016/03
- 21 -
12. Functional Descriptions
■ System Clock
The external clocks which are required to operate the AK4438 are MCLK, LRCK and BICK. MCLK should
be synchronized with LRCK and BICK but the phase is not critical. There are two methods to set MCLK
frequency. In Manual Setting Mode (ACKS bit= “0”: Default), the sampling speed is set by DFS2-0 bit
(Table 1). The frequency of MCLK at each sampling speed is set automatically (Table 2, Table 3). In Auto
Setting Mode (ACKS bit= “1”), as MCLK frequency is detected automatically (Table 4) and the internal
master clock attains the appropriate frequency (Table 5), so it is not necessary to set DFS2-0 bits.
After exiting reset at power-up (PDN pin = “L” →“H”), the AK4438 is in power-down mode until MCLK and
LRCK are input. The AK4438 is set to Manual Setting Mode at power-up (PDN pin = “L” →“H”). When
changing the clock, the AK4438 must be reset by the PDN pin or RSTN bit.
If the clock is stopped, a click noise occurs when restarting the clock. Mute the digital output externally if
the click noise affects system applications.
[AK4438]
016001925-E-00 2016/03
- 22 -
1. Manual Setting Mode (ACKS bit = “0”)
MCLK frequency is detected automatically and the sampling rate is set by DFS2-0 bits (Table 1). The
MCLK frequency corresponding to each sampling speed should be provided externally (Table 2, Table 3).
The AK4438 is set to Manual Setting Mode at power-up (PDN pin = “L” →“H”). When DFS2-0 bits are
changed, the AK4438 should be reset by RSTN bit.
DFS2
DFS1
DFS0
Sampling Speed Mode (fs)
(default)
0
0
0
Normal Speed Mode
8kHz~48kHz
0
0
1
Double Speed Mode
48kHz~96kHz
0
1
0
Quad Speed Mode
96kHz~192kHz
0
1
1
N/A
N/A
1
0
0
Oct Speed Mode
384kHz
1
0
1
Hex Speed Mode
768kHz
1
1
0
N/A
N/A
1
1
1
N/A
N/A
(N/A: Not Available)
Table 1. Sampling Speed (Manual Setting Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
32fs
48fs
64fs
96fs
8.0kHz
N/A
N/A
N/A
N/A
Normal
44.1kHz
N/A
N/A
N/A
N/A
48.0kHz
N/A
N/A
N/A
N/A
88.2kHz
N/A
N/A
N/A
N/A
Double
96.0kHz
N/A
N/A
N/A
N/A
176.4kHz
N/A
N/A
N/A
N/A
Quad
192.0kHz
N/A
N/A
N/A
N/A
384.0kHz
N/A
N/A
24.576
36.864
Oct
768.0kHz
24.576
36.864
N/A
N/A
Hex
Table 2. System Clock Example (Manual Setting Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
128fs
192fs
256fs
384fs
512fs
768fs
8.0kHz
N/A
N/A
2.0480
3.0720
4.0960
6.1440
Normal
44.1kHz
N/A
N/A
11.2896
16.9344
22.5792
33.8688
48.0kHz
N/A
N/A
12.2880
18.4320
24.5760
36.8640
88.2kHz
N/A
N/A
22.5792
33.8688
N/A
N/A
Double
96.0kHz
N/A
N/A
24.5760
36.8640
N/A
N/A
176.4kHz
22.5792
33.8688
N/A
N/A
N/A
N/A
Quad
192.0kHz
24.5760
36.8640
N/A
N/A
N/A
N/A
384.0kHz
N/A
N/A
N/A
N/A
N/A
N/A
Oct
768.0kHz
N/A
N/A
N/A
N/A
N/A
N/A
Hex
Table 3. System Clock Example (Manual Setting Mode)
[AK4438]
016001925-E-00 2016/03
- 23 -
2. Auto Setting Mode (ACKS bit = “1”)
MCLK frequency and the sampling speed are detected automatically (Table 4) and DFS2-0 bits are
ignored. The MCLK frequency corresponding to each sampling speed should be provided externally
(Table 5, Table 6).
MCLK
Sampling Speed Mode
512fs/256fs
768fs/384fs
Normal Speed Mode
256fs
384fs
Double Speed Mode
128fs
192fs
Quad Speed Mode
64fs
96fs
Oct Speed Mode
32fs
48fs
Hex Speed Mode
Table 4. Sampling Speed (Auto Setting Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
32fs
48fs
64fs
96fs
8.0kHz
N/A
N/A
N/A
N/A
Normal
44.1kHz
N/A
N/A
N/A
N/A
48.0kHz
N/A
N/A
N/A
N/A
88.2kHz
N/A
N/A
N/A
N/A
Double
96.0kHz
N/A
N/A
N/A
N/A
176.4kHz
N/A
N/A
N/A
N/A
Quad
192.0kHz
N/A
N/A
N/A
N/A
384.0kHz
N/A
N/A
24.576
36.864
Oct
768.0kHz
24.576
36.864
N/A
N/A
Hex
Table 5. System Clock Example (Auto Setting Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
128fs
192fs
256fs
384fs
512fs
768fs
8.0kHz
N/A
N/A
2.0480
3.0720
4.0960
6.1440
Normal
44.1kHz
N/A
N/A
11.2896
16.9344
22.5792
33.8688
48.0kHz
N/A
N/A
12.2880
18.4320
24.5760
36.8640
88.2kHz
N/A
N/A
22.5792
33.8688
N/A
N/A
Double
96.0kHz
N/A
N/A
24.5760
36.8640
N/A
N/A
176.4kHz
22.5792
33.8688
N/A
N/A
N/A
N/A
Quad
192.0kHz
24.5760
36.8640
N/A
N/A
N/A
N/A
384.0kHz
N/A
N/A
N/A
N/A
N/A
N/A
Oct
768.0kHz
N/A
N/A
N/A
N/A
N/A
N/A
Hex
Table 6. System Clock Example (Auto Setting Mode)
MCLK= 256fs/384fs supports sampling rate of 8kHz~96kHz (Table 7). However, when the sampling rate
is 8kHz~48kHz, DR and S/N will degrade by approximately 3dB as compared to when MCLK=
512fs/768fs.
ACKS bit
MCLK
DR,S/N
L
256fs/384fs/512fs/768fs
108dB
H
256fs/384fs
105dB
H
512fs/768fs
108dB
Table 7. Relationship of DR, S/N and MCLK frequency (fs = 44.1kHz)
[AK4438]
016001925-E-00 2016/03
- 24 -
■ De-emphasis Filter
The AK4438 has a digital de-emphasis filter (tc=50/15µs) by an IIR filter. The de-emphasis filter only
supports Normal Speed Mode. This filter corresponds to three sampling frequencies (32kHz, 44.1kHz,
48kHz). De-emphasis of each DAC can be set individually for DAC1(SDTI1), DAC2(SDTI2),
DAC3(SDTI3) and DAC4(SDTI4) by register settings.
Mode
Sampling Speed
Mode
DEM11
(DEM41-21)
DEM10
(DEM40-20)
DEM
0
Normal Speed Mode
0
0
44.1kHz
1
Normal Speed Mode
0
1
OFF
(default)
2
Normal Speed Mode
1
0
48kHz
3
Normal Speed Mode
1
1
32kHz
Table 8. De-emphasis Control
[AK4438]
016001925-E-00 2016/03
- 25 -
■ Audio Interface Format
TDM1-0 bits, DIF2-0 bits, SDS2-0 bits, TDM1-0 pins and DIF pin settings should not be changed during
operation.
[1] PCM Mode
Normal Mode (TDM1-0 bit=“00”)
Eight channels audio data is shifted in via the SDTI1-4 pins using BICK and LRCK inputs. Data is selected
by SDS2-0 bits. Eight data formats are supported and selected by the DIF2-0 bits as shown in Table 9. In
all formats the serial data is MSB first, 2's compliment format and is latched on the rising edge of BICK.
Mode 2 can be used in 16-bit and 20-bit MSB justified and Mode 6 can be used in 16-bit, 20-bit and 24-bit
MSB justified formats by zeroing the unused LSBs.
TDM128 Mode (TDM1-0 bit=“01”)
Eight channels audio data is shifted in via the SDTI1-2 pins using BICK and LRCK inputs. Data is selected
by SDS2-0 bits. The data input to the SDTI3-4 pins are ignored. BICK is fixed to 128fs. Six data formats
are supported and selected by the DIF2-0 bits as shown in Table 9. In all formats the serial data is MSB
first, 2's compliment format and is latched on the rising edge of BICK.
TDM256 Mode (TDM1-0 bit=“10”)
Sixteen channels audio data is shifted in via the SDTI1-2 pins using BICK and LRCK inputs. Data is
selected by SDS2-0 bits. The data input to the SDTI3-4 pins are ignored. BICK is fixed to 256fs. Six data
formats are supported and selected by the DIF2-0 bits as shown in Table 9. In all formats the serial data is
MSB first, 2's compliment format and is latched on the rising edge of BICK.
TDM512 Mode (TDM1-0 bit=“11”)
Sixteen channels audio data is shifted in via the SDTI1 pin using BICK and LRCK inputs. Data is selected
by SDS2-0 bits. The data input to the SDTI2-4 pins are ignored. BICK is fixed to 512fs. Six data formats
are supported and selected by the DIF2-0 bits as shown in Table 9. In all formats the serial data is MSB
first, 2's compliment format and is latched on the rising edge of BICK.
[AK4438]
016001925-E-00 2016/03
- 26 -
Mode
TDM1
TDM0
DIF2
DIF1
DIF0
SDTI Format
LRCK
BICK
Normal
(Note 21)
0
0
0
0
0
0
16-bit LSB justified
H/L
32fs
1
0
0
1
20-bit LSB justified
H/L
40fs
2
0
1
0
24-bit MSB justified
H/L
48fs
3
0
1
1
16-bit I2S compatible
L/H
32fs
24-bit I2S compatible
L/H
48fs
4
1
0
0
24-bit LSB justified
H/L
48fs
5
1
0
1
32-bit LSB justified
H/L
64fs
6
1
1
0
32-bit MSB justified
H/L
64fs
7
1
1
1
32-bit I2S compatible
L/H
64fs
TDM128
-
0
1
0
0
0
N/A
128fs
-
0
0
1
N/A
128fs
8
0
1
0
24-bit MSB justified
128fs
9
0
1
1
24-bit I2S compatible
128fs
10
1
0
0
24-bit LSB justified
128fs
11
1
0
1
32-bit LSB justified
128fs
12
1
1
0
32-bit MSB justified
128fs
13
1
1
1
32-bit I2S compatible
128fs
TDM256
-
1
0
0
0
0
N/A
256fs
-
0
0
1
N/A
256fs
14
0
1
0
24-bit MSB justified
256fs
15
0
1
1
24-bit I2S compatible
256fs
16
1
0
0
24-bit LSB justified
256fs
17
1
0
1
32-bit LSB justified
256fs
18
1
1
0
32-bit MSB justified
256fs
19
1
1
1
32-bit I2S compatible
256fs
TDM512
-
1
1
0
0
0
N/A
512fs
-
0
0
1
N/A
512fs
20
0
1
0
24-bit MSB justified
512fs
21
0
1
1
24-bit I2S compatible
512fs
22
1
0
0
24-bit LSB justified
512fs
23
1
0
1
32-bit LSB justified
512fs
24
1
1
0
32-bit MSB justified
512fs
25
1
1
1
32-bit I2S compatible
512fs
Note 21. BICK that is input to each channel must be longer than the bit length of setting format.
(N/A: Not available)
Table 9. Audio Data Format
[AK4438]
016001925-E-00 2016/03
- 27 -
SDTI1-4
BICK
LRCK
SDTI1-4
15
14
6
5
4
BICK
0
1
10
11
12
13
14
15
0
1
10
11
12
13
14
15
0
1
3
2
1
0
15
14
(32fs)
(64fs)
0
14
1
15
16
17
31
0
1
14
15
16
17
31
0
1
15
14
0
15
14
0
Mode 0
Don’t care
Don’t care
15:MSB, 0:LSB
Mode 0
15
14
6
5
4
3
2
1
0
Lch Data
Rch Data
Figure 11. Mode 0 Timing
SDTI1-4
LRCK
BICK
(64fs)
0
9
1
10
11
12
31
0
1
9
10
11
12
31
0
1
19
0
19
0
Mode 1
Don’t care
Don’t care
19:MSB, 0:LSB
SDTI1-4
Mode 4
23:MSB, 0:LSB
20
19
0
20
19
0
Don’t care
Don’t care
22
21
22
21
Lch Data
Rch Data
8
23
23
8
Figure 12. Mode 1/4 Timing
LRCK
BICK
(64fs)
SDTI1-4
0
22
1
2
24
31
0
1
31
0
1
23:MSB, 0:LSB
22
1
0
Don’t care
23
Lch Data
Rch Data
23
30
22
2
24
23
30
22
1
0
Don’t care
23
22
23
Figure 13. Mode 2 Timing
[AK4438]
016001925-E-00 2016/03
- 28 -
LRCK
BICK
(64fs)
SDTI1-4
0
3
1
2
24
31
0
1
31
0
1
23:MSB, 0:LSB
22
1
0
Don’t care
23
Lch Data
Rch Data
23
25
3
2
24
23
25
22
1
0
Don’t care
23
23
Figure 14. Mode 3 Timing
LRCK
BICK
(64fs)
SDTI1-4
0
22
1
2
24
31
0
1
31
0
1
32:MSB, 0:LSB
30
1
0
31
Lch Data
Rch Data
23
30
22
2
24
23
30
30
1
0
31
30
31
Mode 5,6
Figure 15. Mode 5/6 Timing
LRCK
BICK
(64fs)
SDTI1-4
0
3
1
2
24
31
0
1
31
0
1
32:MSB, 0:LSB
30
1
0
31
Lch Data
Rch Data
23
25
3
2
24
23
25
30
1
0
31
30
31
Figure 16. Mode 7 Timing
[AK4438]
016001925-E-00 2016/03
- 29 -
LRCK
BICK(128fs)
128 BICK
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
SDTI1-2
22
0
22
0
22
0
22
0
23
23
23
23
22
23
Mode8
SDTI1-2
30
0
30
0
30
2
0
30
0
31
31
31
31
30
31
Mode11,12
Figure 17. Mode 8/11/12 Timing
LRCK
BICK(128fs)
128 BICK
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
SDTI1-2
22
0
22
0
22
0
22
0
23
23
23
23
23
SDTI1-2
Mode9
Mode13
30
0
30
0
30
2
0
30
0
31
31
31
31
30
31
Figure 18. Mode 9/13 Timing
LRCK
BICK(128fs)
128 BICK
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
SDTI1-2
22
0
22
0
22
0
22
0
23
23
23
23
23
Figure 19. Mode 10 Timing
[AK4438]
016001925-E-00 2016/03
- 30 -
23
LRCK
BICK (256fs)
22
0
L1
32 BICK
256 BICK
22
0
R1
32 BICK
22
23
23
22
0
L2
32 BICK
22
0
R2
32 BICK
23
23
SDTI1-2
31
30
0
30
31
31
30
0
31
30
0
31
30
0
SDTI1-2
Mode14
Mode17,18
23
22
0
L3
32 BICK
22
0
R3
32 BICK
23
22
0
L4
32 BICK
22
0
R4
32 BICK
23
23
31
30
0
31
30
0
31
30
0
31
30
0
Figure 20. Mode 14/17/18 Timing
LRCK
BICK (256fs)
23
0
L1
32 BICK
256 BICK
23
0
R1
32 BICK
23
23
0
L2
32 BICK
23
0
R2
32 BICK
SDTI1-2
Mode15
31
0
31
30
31
0
30
31
0
30
31
0
30
SDTI1-2
Mode19
23
0
L3
32 BICK
23
0
R3
32 BICK
23
0
L4
32 BICK
23
0
R4
32 BICK
31
0
30
31
0
30
31
0
30
31
0
30
Figure 21. Mode 15/19 Timing
LRCK
BICK(256fs)
SDTI1-2
256 BICK
22
0
L1
32 BICK
22
0
R1
32 BICK
22
0
L2
32 BICK
22
0
R2
32 BICK
23
23
23
23
23
22
0
L3
32 BICK
22
0
R3
32 BICK
22
0
L4
32 BICK
22
0
R4
32 BICK
23
23
23
23
Figure 22. Mode 16 Timing
[AK4438]
016001925-E-00 2016/03
- 31 -
BICK(512fs)
SDTI1
Mode8
LRCK
512BICK
22
0
23
22
0
23
22
0
23
22
0
23
22
2
0
23
22
0
23
22
0
23
22
0
23
SDTI1
Mode11,12
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
22
0
31
23
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
31
Figure 23. Mode 20/23/24 Timing
BICK(512fs)
SDTI1
Mode21
LRCK
512BICK
22
0
23
22
0
23
22
0
23
22
0
23
22
2
0
23
22
0
23
22
0
23
22
0
23
SDTI1
Mode25
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
22
0
31
23
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
22
0
31
31
Figure 24. Mode 21/25 Timing
BICK(512fs)
SDTI1
Mode22
LRCK
512BICK
22
0
23
22
0
23
22
0
23
22
0
23
22
2
0
23
22
0
23
22
0
23
22
0
23
L1
32 BICK
R1
32 BICK
L2
32 BICK
R2
32 BICK
L3
32 BICK
R3
32 BICK
L4
32 BICK
R4
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
32 BICK
23
Figure 25. Mode 22 Timing
[AK4438]
016001925-E-00 2016/03
- 32 -
[2] Data Select
SDS2-0 bits control the playback channel of each DAC.
LRCK
SDTI1
R1
L1
SDTI2
R2
L2
SDTI3
R3
L3
SDTI4
R4
L4
Figure 26. Data Slot in Normal Mode
SDTI1
R1
L1
SDTI2
LRCK
128 BICK
R2
L2
R3
L3
R4
L4
Figure 27. Data Slot in TDM128 Mode
SDTI1
R1
L1
LRCK
256 BICK
R2
L2
R3
L3
R4
L4
SDTI2
R5
L5
R6
L6
R7
L7
R8
L8
Figure 28. Data Slot in TDM256 Mode
SDTI1
R1
L1
LRCK
512 BICK
R2
L2
R3
L3
R4
L4
R5
R6
L6
R7
L7
R8
L8
L5
Figure 29. Data Slot in TDM512 Mode
[AK4438]
016001925-E-00 2016/03
- 33 -
SDS2
SDS1
SDS0
DAC1
DAC2
DAC3
DAC4
Lch
Rch
Lch
Rch
Lch
Rch
Lch
Rch
Normal
*
0
0
L1
R1
L2
R2
L3
R3
L4
R4
*
0
1
L2
R2
L3
R3
L4
R4
L1
R1
*
1
0
L3
R3
L4
R4
L1
R1
L2
R2
*
1
1
L4
R4
L1
R1
L2
R2
L3
R3
TDM128
*
0
0
L1
R1
L2
R2
L3
R3
L4
R4
*
0
1
L2
R2
L3
R3
L4
R4
L1
R1
*
1
0
L3
R3
L4
R4
L1
R1
L2
R2
*
1
1
L4
R4
L1
R1
L2
R2
L3
R3
TDM256
0
0
0
L1
R1
L2
R2
L3
R3
L4
R4
0
0
1
L2
R2
L3
R3
L4
R4
L5
R5
0
1
0
L3
R3
L4
R4
L5
R5
L6
R6
0
1
1
L4
R4
L5
R5
L6
R6
L7
R7
1
0
0
L5
R5
L6
R6
L7
R7
L8
R8
1
0
1
L6
R6
L7
R7
L8
R8
L1
R1
1
1
0
L7
R7
L8
R8
L1
R1
L2
R2
1
1
1
L8
R8
L1
R1
L2
R2
L3
R3
TDM512
0
0
0
L1
R1
L2
R2
L3
R3
L4
R4
0
0
1
L2
R2
L3
R3
L4
R4
L5
R5
0
1
0
L3
R3
L4
R4
L5
R5
L6
R6
0
1
1
L4
R4
L5
R5
L6
R6
L7
R7
1
0
0
L5
R5
L6
R6
L7
R7
L8
R8
1
0
1
L6
R6
L7
R7
L8
R8
L1
R1
1
1
0
L7
R7
L8
R8
L1
R1
L2
R2
1
1
1
L8
R8
L1
R1
L2
R2
L3
R3
(*: Do not care) Table 10. Data Select
[AK4438]
016001925-E-00 2016/03
- 34 -
■ Digital Filter
Five digital filters are available for playback, providing a choice of different sound colors. These digital
filters are selected by SD bit, SLOW bit and SSLOW bit.
SSLOW
SD bit
SLOW bit
Mode
0
0
0
Sharp roll-off filter
0
0
1
Slow roll-off filter
0
1
0
Short delay Sharp roll-off filter
(default)
0
1
1
Short delay Slow roll-off filter
1
*
*
Super Slow Roll-off Mode
Table 11. Digital Filter Setting (*: don’t care)
■ Zero Detection
The AK4438 has channel-independent zero detection function. Zero detection channels (AOUTL1-4 and
AOUTR1-4 pins) can be selected by 07H/08H registers (L1-4 bits, R1-4 bits). When the input data at each
channel is continuously zeros for 8192 LRCK cycles, the DZF pin goes to “H”. The DZF pin immediately
returns to “L” if the input data of each channel is not zero. If the RSTN bit is “0”, the DZF pins of both
channels go to “H”. The DZF pin of both channels go to “L” after 4 ~ 5/fs when RSTN bit returns to “1”. The
DZFB bit can invert the polarity of the DZF pin. If all channels are disabled, the DZF pin outputs “Not
zero”.
DZFB bit
Data
DZF pin
0
Not zero
L
Zero detect
H
1
Not zero
H
Zero detect
L
Not zero: One of the zero detection channels set by L1-4 bits and R1-4 bits does not detect zero.
Zero detect: All zero detection channels set by L1-4 bits and R1-4 bits detect zero.
Table 12. DZF Pin Function
[AK4438]
016001925-E-00 2016/03
- 35 -
■ Digital Volume Function
The AK4438 has a channel-independent digital attenuator (256 levels, 0.5dB steps). Attenuation level of
each DAC1-4 can be set by ATT7-0 bits (register 0A-11H), respectively (Table 13).
ATT7-0bits
(register 0A-11H)
Attenuation Level
FFH
+0dB
(default)
FEH
-0.5dB
FDH
-1.0dB
:
:
:
:
02H
-126.5dB
01H
-127.0dB
00H
MUTE (-∞)
Table 13. Attenuation level of Digital Attenuator
Transition time between set values of ATT7-0 bits can be selected by the ATS1-0 bits (Table 14). The
transition between set values is a soft transition in Mode0/1/2 eliminating switching noise in the transition.
Mode
ATS1
ATS0
ATT speed
0
0
0
4080/fs
(default)
1
0
1
2040/fs
2
1
0
510/fs
3
1
1
255/fs
Table 14. Transition Time of Digital Volume
The transition between set values is a soft transition of 4080 levels in Mode 0. It takes 4080/fs (85ms
@fs=48kHz) from FFH to 00H. If the PDN pin goes to “L”, ATT7-0 bits are initialized to FFH.
If the digital volume is changed during reset, the volume will be changed to the setting value after
releasing the reset. If the volume is changed in 5/fs after releasing a reset, the volume is changed
immediately without soft transition.
[AK4438]
016001925-E-00 2016/03
- 36 -
■ LR Channel Output Signal Select
Input and output signal combination of the AK4438 can be set by MONO1-4 bits and SELLR1-4 bits. The
output signal phase of DAC is controlled by INVL1-4 and INVR1-4 bits. These settings are available for
any audio format.
MONO1 bit
SELLR1 bit
INVL1 bit
INVR1 bit
L1ch Out
R1ch Out
0
0
0
0
L1ch In
R1ch In
1
0
L1ch In Invert
R1ch In
0
1
L1ch In
R1ch In Invert
1
1
L1ch In Invert
R1ch In Invert
0
1
0
0
R1ch In
L1ch In
1
0
R1ch In Invert
L1ch In
0
1
R1ch In
L1ch In Invert
1
1
R1ch In Invert
L1ch In Invert
1
0
0
0
L1ch In
L1ch In
1
0
L1ch In Invert
L1ch In
0
1
L1ch In
L1ch In Invert
1
1
L1ch In Invert
L1ch In Invert
1
1
0
0
R1ch In
R1ch In
1
0
R1ch In Invert
R1ch In
0
1
R1ch In
R1ch In Invert
1
1
R1ch In Invert
R1ch In Invert
Table 15. Output Select for DAC1
MONO2 bit
SELLR2 bit
INVL2 bit
INVR2 bit
L2ch Out
R2ch Out
0
0
0
0
L2ch In
R2ch In
1
0
L2ch In Invert
R2ch In
0
1
L2ch In
R2ch In Invert
1
1
L2ch In Invert
R2ch In Invert
0
1
0
0
R2ch In
L2ch In
1
0
R2ch In Invert
L2ch In
0
1
R2ch In
L2ch In Invert
1
1
R2ch In Invert
L2ch In Invert
1
0
0
0
L2ch In
L2ch In
1
0
L2ch In Invert
L2ch In
0
1
L2ch In
L2ch In Invert
1
1
L2ch In Invert
L2ch In Invert
1
1
0
0
R2ch In
R2ch In
1
0
R2ch In Invert
R2ch In
0
1
R2ch In
R2ch In Invert
1
1
R2ch In Invert
R2ch In Invert
Table 16. Output Select for DAC2
[AK4438]
016001925-E-00 2016/03
- 37 -
MONO3 bit
SELLR3 bit
INVL3 bit
INVR3 bit
L3
R3
0
0
0
0
L3ch In
R3ch In
1
0
L3ch In Invert
R3ch In
0
1
L3ch In
R3ch In Invert
1
1
L3ch In Invert
R3ch In Invert
0
1
0
0
R3ch In
L3ch In
1
0
R3ch In Invert
L3ch In
0
1
R3ch In
L3ch In Invert
1
1
R3ch In Invert
L3ch In Invert
1
0
0
0
L3ch In
L3ch In
1
0
L3ch In Invert
L3ch In
0
1
L3ch In
L3ch In Invert
1
1
L3ch In Invert
L3ch In Invert
1
1
0
0
R3ch In
R3ch In
1
0
R3ch In Invert
R3ch In
0
1
R3ch In
R3ch In Invert
1
1
R3ch In Invert
R3ch In Invert
Table 17. Output Select for DAC3
MONO4 bit
SELLR4 bit
INVL4 bit
INVR4 bit
L4
R4
0
0
0
0
L4ch In
R4ch In
1
0
L4ch In Invert
R4ch In
0
1
L4ch In
R4ch In Invert
1
1
L4ch In Invert
R4ch In Invert
0
1
0
0
R4ch In
L4ch In
1
0
R4ch In Invert
L4ch In
0
1
R4ch In
L4ch In Invert
1
1
R4ch In Invert
L4ch In Invert
1
0
0
0
L4ch In
L4ch In
1
0
L4ch In Invert
L4ch In
0
1
L4ch In
L4ch In Invert
1
1
L4ch In Invert
L4ch In Invert
1
1
0
0
R4ch In
R4ch In
1
0
R4ch In Invert
R4ch In
0
1
R4ch In
R4ch In Invert
1
1
R4ch In Invert
R4ch In Invert
Table 18. Output Select for DAC4
[AK4438]
016001925-E-00 2016/03
- 38 -
■ Soft Mute Operation
The soft mute operation is performed at digital domain. When the SMUTE pin goes to “H” or set SMUTE
bit to “1”, the output signal is attenuated by during ATT_DATA ATT transition time from the current
ATT level. When the SMUTE pin is returned to “L” or the SMUTE bit is returned to “0”, the mute is
cancelled and the output attenuation gradually changes to the ATT level during ATT_DATA ATT
transition time. If the soft mute is cancelled before attenuating , the attenuation is discontinued and
returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without
stopping the signal transmission.
SMUTE pin or
SMUTE bit
Attenuation
DZF pin
ATT_Level
-
AOUT
8192/fs
GD
GD
(1)
(2)
(3)
(4)
(1)
(2)
Notes:
(1) ATT_DATA ATT transition time. For example, this time is 4080LRCK cycles at ATT_DATA=255 in
Normal Speed Mode.
(2) The analog output corresponding to the digital input has group delay (GD).
(3) If the soft mute is cancelled before attenuating after starting the operation, the attenuation is
discontinued and returned to ATT level by the same cycle.
(4) When the input data for a zero detection channel is continuously zeros for 8192 LRCK cycles, the
DZF pin goes to “H”. The DZF pin immediately returns to “L” if input data are not zero.
Figure 30. Soft Mute Function and Zero Detection
[AK4438]
016001925-E-00 2016/03
- 39 -
■ Error Detection
Three types of error can be detected in I2C mode when the LDOE pin = “H”. (Table 19).When the error is
detected, LDO is powered down and writing into the control registers is prohibited. Once the error is
detected the AK4438 does not return to normal operation automatically even if the error condition is
removed so restart the AK4438 by the PDN pin. In I2C mode, the AK4438 does not generate
acknowledge (ACK) in error status.
No
Error
Error Condition
1
Internal Reference Voltage Error
Internal reference voltage is not powered up.
2
LDO Over Voltage Detection
LDO voltage > 1.5V (typ.)
3
LDO Over Current Detection
LDO current < 51mA (typ.)
Table 19. Error Detection
■ System Reset
The AK4438 should be reset once by bringing the PDN pin = “L” upon power-up. Power-down state of the
reference voltage such as LDO and VCOM will be released by PDN pin = “H” and writing into resisters is
valid in 1ms. The AK4438 is in power-down state until MCLK and LRCK input.
[AK4438]
016001925-E-00 2016/03
- 40 -
■ Power Down Function
The AK4438 is placed in power-down mode by bringing the PDN pin “L” and the analog outputs become
floating (Hi-Z) state. Power-up and power-down timings are shown in Figure 31.
PDN pin
Power
Reset
Normal Operation (Register Write and DAC input are available)
Clock In
MCLK,LRCK,BICK
DAC In
(Digital)
DAC Out
(Analog)
External
Mute
Mute ON
(7)
DZF
Don’t care
“0”data
GD
(3)
(5)
(6)
(8)
GD
(5)
Mute ON
“0”data
Don’t care
Internal
State
(4)
(4)
(1)
Internal PDN
(2)
LDOO pin
Notes:
(1) After AVDD and TVDD are powered-up, the PDN pin should be “L” for 800ns.
(2) After PDN pin = “H”, the internal LDO and VCOM power-up. The internal registers are initialized.
Register writing is available in 1msec after PDN pin = “H”.
(3) The analog output corresponding to digital input has group delay (GD).
(4) Analog outputs are floating (Hi-Z) in power down mode.
(5) Click noise occurs at an edge of PDN signal. This noise is output even if “0” data is input.
(6) MCLK, BICK and LRCK clocks can be stopped in power-down mode (PDN pin= “L”).
(7) Mute the analog output externally if click noise (5) adversely affect system performance
The timing example is shown in this figure.
(8) The DZF pin outputs “L” in internal power-down mode.
Figure 31. Pin Power Down/Up Sequence Example
[AK4438]
016001925-E-00 2016/03
- 41 -
■ Power Off and Reset Functions
Analog Output
RSTN
PW4-1
DAC4
DAC3
DAC2
DAC1
0
0000
Hi-Z
Hi-Z
Hi-Z
Hi-Z
0
0001
Hi-Z
Hi-Z
Hi-Z
VCOM
0
0010
Hi-Z
Hi-Z
VCOM
Hi-Z
0
0011
Hi-Z
Hi-Z
VCOM
VCOM
0
0100
Hi-Z
VCOM
Hi-Z
Hi-Z
0
0101
Hi-Z
VCOM
Hi-Z
VCOM
0
0110
Hi-Z
VCOM
VCOM
Hi-Z
0
0111
Hi-Z
VCOM
VCOM
VCOM
0
1000
VCOM
Hi-Z
Hi-Z
Hi-Z
0
1001
VCOM
Hi-Z
Hi-Z
VCOM
0
1010
VCOM
Hi-Z
VCOM
Hi-Z
0
1011
VCOM
Hi-Z
VCOM
VCOM
0
1100
VCOM
VCOM
Hi-Z
Hi-Z
0
1101
VCOM
VCOM
Hi-Z
VCOM
0
1110
VCOM
VCOM
VCOM
Hi-Z
0
1111
VCOM
VCOM
VCOM
VCOM
1
0000
Hi-Z
Hi-Z
Hi-Z
Hi-Z
1
0001
Hi-Z
Hi-Z
Hi-Z
Normal
1
0010
Hi-Z
Hi-Z
Normal
Hi-Z
1
0011
Hi-Z
Hi-Z
Normal
Normal
1
0100
Hi-Z
Normal
Hi-Z
Hi-Z
1
0101
Hi-Z
Normal
Hi-Z
Normal
1
0110
Hi-Z
Normal
Normal
Hi-Z
1
0111
Hi-Z
Normal
Normal
Normal
1
1000
Normal
Hi-Z
Hi-Z
Hi-Z
1
1001
Normal
Hi-Z
Hi-Z
Normal
1
1010
Normal
Hi-Z
Normal
Hi-Z
1
1011
Normal
Hi-Z
Normal
Normal
1
1100
Normal
Normal
Hi-Z
Hi-Z
1
1101
Normal
Normal
Hi-Z
Normal
1
1110
Normal
Normal
Normal
Hi-Z
1
1111
Normal
Normal
Normal
Normal
Table 20. Power OFF and Reset Function
[AK4438]
016001925-E-00 2016/03
- 42 -
(1) Power OFF Function (PW4-1 bits)
All DAC4-1 can be powered down immediately by setting PW4-1 bits to “0000”. In this time, the analog
output goes to floating state (Hi-z). DACs will be reset and the digital block is powered down by setting
RSTN bit to “0”. In the reset state, the analog output becomes VCOM voltage if DAC is powered-up and
MCLK, LRCK and BICK are supplied (Table 20). Internal register values are not initialized by power-off or
reset by bit settings. Figure 32 shows a timing example of power-on and power-down.
Normal Operation
Internal
State
PMDA4-1bit
Power-off
Normal Operation
GD
GD
“0” data
D/A Out
(Analog)
D/A In
(Digital)
Clock In
MCLK, BICK, LRCK
(1)
(3)
(6)
DZF
External
MUTE
(5)
(3)
(1)
Mute ON
(2)
(4)
Don’t care
Notes:
(1) The analog output corresponding to digital input has group delay (GD).
(2) Analog outputs are floating (Hi-Z) in power down mode.
(3) Click noise occurs at the edges (“ ”) of the internal timing of PW4-1 bits. This noise is output
even if “0” data is input.
(4) Each clock input (MCLK, BICK, LRCK) can be stopped in power down mode (PW4-1 bits =
“0000”).
(5) Mute the analog output externally if the click noise (3) adversely affect system performance.
(6) The DZF pin outputs “L”, in power down mode (PW4-1 bits = “0000”).
Figure 32. Power-off/on Sequence Example
[AK4438]
016001925-E-00 2016/03
- 43 -
(2) Reset Function (RSTN bit)
The DAC can be reset by setting RSTN bit to “0” but the internal registers are not initialized. In this time,
the corresponding analog outputs go to VCOM and the DZF pin outputs “H” if clocks (MCLK, BICK and
LRCK) are input. Figure 33 shows an example of reset sequence by RSTN bit.
Internal
State
RSTN bit
Digital Block
Power-down
Normal Operation
GD
GD
“0” data
D/A Out
(Analog)
D/A In
(Digital)
Clock In
BICK
(1)
(3)
DZF
(3)
(1)
(2)
Normal Operation
2/fs
Internal
RSTN bit
2~3/fs
3~4/fs
Don’t care
(4)
(5)
Notes:
(1) he analog output corresponding to digital input has group delay (GD).
(2) Analog outputs are VCOM in power down mode.
(3) Click noise occurs at the edges (“ ”) of the internal timing of RSTN bit. This noise is output even
if “0” data is input.
(4) The DZF pin goes to “H” on the falling edge of RSTN bit and goes to “L” in 2/fs after a rising edge
of the internal RSTN.
(5) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit
“1” to the internal RSTN bit “1”.
Figure 33. Reset Sequence Example
[AK4438]
016001925-E-00 2016/03
- 44 -
(3) Reset Function (MCLK)
The AK4438 is automatically placed in reset state when MCLK is stopped during normal operation (PDN
pin = “H”), and the analog outputs go to VCOM voltage. When MCLK are input again, the AK4438 exits
reset state and starts the operation. Zero detect function is disable when MCLK is stopped.
Normal Operation
Internal
State
Digital Circuit Power-down
Normal Operation
GD
GD
D/A Out
(Analog)
D/A In
(Digital)
Clock In
MCLK
(2)
(4)
External
MUTE
(6)
(2)
MCLK Stop
RSTN bit
Power-down
Power-down
(5)
(5)
(5)
Hi-Z
(6)
(1)
AVDD pin
TVDD pin
(6)
(3)
Notes:
(1) After AVDD and TVDD are powered-up, the PDN pin should be “L” for 800ns.
(2) The analog output corresponding to digital input has group delay (GD).
(3) When MCLK is stopped, analog outputs go to VCOM voltage.
(4) The digital data can be stopped. Click noise after MCLK is input again can be reduced by inputting
“0” data during this period.
(5) Click noise occurs within 3 ~ 4LRCK cycles from the riding edge (“↑”) of the PDN pin or MCLK
inputs. This noise occurs even when “0” data is input.
(6) Mute the analog output externally if click noise (5) influences system applications. The timing
example is shown in this figure.
Figure 34. Reset Sequence Example2
[AK4438]
016001925-E-00 2016/03
- 45 -
■ Clock Synchronization
The AK4438 has a function that resets the internal counter to keep a falling edge of the internal FSI clock
is in 3/256fs from an edge of the external FSI clock. Clock synchronization function becomes valid when
data at all channels are continuously “0” for 8192 times if SYNCE bit is set to “1” during operation in PCM
mode or when RSTN bit is set to “0”. The operation clock is synchronized to a falling edge of LRCK in
PCM mode and a rising edge of LRCK in I2C mode.
The analog output becomes VCOM voltage when RSTN bit = “0” or zero data is detected. Figure 35
shows a synchronization sequence when the input data is “0” for 8192 times continuously. Figure 36
shows a synchronization sequence by RSTN bit.
(1) Clock Synchronization Sequence when Input Data is “0” for 8192 Cycles Continuously
The DZF pin goes to “H” and the synchronization function becomes enabled when input data is “0” for
8192 time continuously including when the data is attenuated. Figure 35 shows a synchronization
sequence.
SMUTE
Attenuation
DZF pin
ATT_Level
-
AOUT
8192/fs
GD
(1)
(2)
(1)
D/A In
(Digital)
GD
GD
8192/fs
(2)
Operation (2)
Operation (2)
Internal Counter
Reset
Internal
Data Reset
4~5/fs (3)
(4)
(5)
Notes:
(1) Refer to Table 14 internal transition time of ATT.
(2) The synchronization function becomes enabled when all channels input data are “0” for 8192 times
continuously.
(3) Internal data is fixed to “0” for 4~5/fs forcibly when the internal counter is reset.
(4) Click noise occurs when the internal counter is reset. This noise is output even if “0” data is input.
Mute the analog output externally if this click noise adversely affects system performance.
(5) The internal counter will not be reset when the internal and the external clocks are synchronized
even if the synchronization function is enabled.
Figure 35. Clock Synchronization Sequence with Continuous Zero Data
[AK4438]
016001925-E-00 2016/03
- 46 -
(2) Clock Synchronization Sequence with RSTN-bit
The DZF pin outputs “H” by setting RSTN bit to “0”. The DAC is reset after 3~4/fs from the DZF pin = “H”,
and the analog output goes to VCOM voltage. The synchronization function is enabled when the DZF pin
= “H”. Figure 36 shows synchronization sequence with RSTN bit.
Internal
State
RSTN bit
Digital Block Power-down
Normal Operation
GD
GD
D/A Out
(Analog)
D/A In
(Digital)
(3)
(5)
DZF
(5)
(3)
Normal Operation
2/fs(4)
Internal
RSTN bit
2~3/fs (4)
3~4/fs (4)
Internal Counter
Reset
Internal
Data Reset
4~5/fs (2)
force”0”
Operation (1)
(2)
Notes:
(1) The DZF pin outputs “H” by a falling edge of RSTN bit, and returns to “L” after 2/fs from the internal
rising edge of RSTN bit. During this period the synchronization function is enabled.
(2) Internal data is fixed to “0” for 4~5/fs forcibly when the internal counter is reset.
(3) The analog output corresponding to digital input has group delay (GD). It is recommended that
when writing “0” data to RSTN bit, “0” period should be longer than the GD period.
(4) It takes 3~4/fs to fall down and 2~3/fs to rise up for the internal RSTN signal from RSTN bit writing.
There is a case that the internal counter is reset before internal RSTN bit is changed to “1” since the
synchronization function becomes enabled immediately by setting RSTN bit = “0”.
(5) A click noise occurs by an internal RSTN signal edge or an internal counter reset. This noise is
output even if “0” data is input. Mute the analog output externally if the click noise adversely affects
the system performance.
Figure 36. Clock Synchronization Sequence by RSTN bit
[AK4438]
016001925-E-00 2016/03
- 47 -
■ Parallel Mode
Parallel mode is available by setting the I2C pin = “H” and the PS pin = “H”. In parallel mode, the register
setting is ignored. Audio interface format and soft mute function are controlled by Pins. Other functions
operate in default setting of registers. The system clock is always in auto setting mode.
■ Audio Interface
Audio interface format of the parallel mode is controlled by TDM1-0 and DIF pins (Table 21).
Zero detection function and functions set by registers are not available in parallel mode.
TDM1 pin
TDM0 pin
DIF pin
Mode
0
0
0
Mode6 (Table 9)
0
0
1
Mode7 (Table 9)
0
1
0
Mode12 (Table 9)
0
1
1
Mode13 (Table 9)
1
0
0
Mode18 (Table 9)
1
0
1
Mode19 (Table 9)
1
1
0
Mode24 (Table 9)
1
1
1
Mode25 (Table 9)
Table 21. Parallel Mode
■ Soft Mute
The soft mute operation is controlled by SMUTE pin (Figure 30).
[AK4438]
016001925-E-00 2016/03
- 48 -
■ Serial Control Interface
The AK4438’s functions are controlled through registers. The registers may be written by two types of
control modes. The internal registers are controlled in 3-wire serial control mode when the I2C pin = “L”
and the PS pin = “L”, and in I2C bus control mode when the I2C pin = “H” and the PS pin = “L”. Chip
address is determined by the CAD0 and CAD1 pins. The internal registers are initialized by setting the
PDN pin to “L”. The internal timing circuit is reset by setting RSTN bit = “0” but register values are not
initialized..
*Register writings are not available when the PDN pin = “L”.
(1) 3-wire Serial Control Mode (I2C pin = “L”)
The internal registers may be written through the 3-wire µP interface pins (CSN, CCLK and CDTI). The
data on this interface consists of a 2-bit Chip address, Read/Write (1bit, Fixed to “1”, Write only), Register
address (MSB first, 5bits) and Control data (MSB first, 8bits). Address and data are clocked in on the
rising edge of CCLK and data is clocked out on the falling edge. For write operations, data is latched after
a low-to-high transition of CSN. The clock speed of CCLK is 5MHz (max).
The internal registers are initialized by setting the PDN pin = “L”. In serial mode, the internal timing circuit
is reset by setting RSTN bit = “0” but register values are not initialized.
CDTI
CCLK
C1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
D4
D5
D6
D7
A1
A2
A3
A4
R/W
C0
A0
D0
D1
D2
D3
CSN
C1-C0: Chip Address (C1=CAD1, C0=CAD0)
R/W: READ/WRITE (Fixed to “1”, Write only)
A4-A0: Register Address
D7-D0: Control Data
Figure 37. Control I/F Timing
* The AK4438 does not support read commands in 3-wire serial control mode.
* When the AK4438 is in power down mode (PDN pin = “L”), a writing into the control registers is
prohibited.
* The control data cannot be written when the CCLK rising edge is 15 times or less, or 17 times or more
during CSN is “L”.
[AK4438]
016001925-E-00 2016/03
- 49 -
(2) I2C-bus Control Mode (I2C pin = “H”)
The AK4438 supports the fast-mode I2C-bus (max: 400kHz, Ver1.0).
(2)-1. WRITE Operations
Figure 38 shows the data transfer sequence of the I2C-bus mode. All commands are preceded by a
START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START
condition (Figure 44). After the START condition, a slave address is sent. This address is 7 bits long
followed by the eighth bit that is a data direction bit (R/W). The most significant five bits of the slave
address are fixed as “00100”. The next bits are CAD1-0 (device address bits). These bits identify the
specific device on the bus. The hard-wired input pins (CAD1-0 pins) set these device address bits (Figure
39). If the slave address matches that of the AK4438, the AK4438 generates an acknowledge and the
operation is executed. The master must generate the acknowledge-related clock pulse and release the
SDA line (HIGH) during the acknowledge clock pulse (Figure 45). R/W bit = “1” indicates that the read
operation is to be executed. “0” indicates that the write operation is to be executed.
The second byte consists of the control register address of the AK4438. The format is MSB first, and
those most significant 3-bits are fixed to zeros (Figure 40). The data after the second byte contains control
data. The format is MSB first, 8bits (Figure 41). The AK4438 generates an acknowledge after each byte is
received. Data transfer is always terminated by a STOP condition generated by the master. A LOW to
HIGH transition on the SDA line while SCL is HIGH defines STOP condition (Figure 44).
The AK4438 can perform more than one byte write operation per sequence. After receipt of the third byte
the AK4438 generates an acknowledge and awaits the next data. The master can transmit more than one
byte instead of terminating the write cycle after the first data byte is transferred. After receiving each data
packet the internal address counter is incremented by one, and the next data is automatically taken into
the next address. If the address exceeds “14H” prior to generating a stop condition, the address counter
will “roll over” to “00H” and the previous data will be overwritten.
The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state
of the data line can only be changed when the clock signal on the SCL line is LOW (Figure 46) except for
the START and STOP conditions.
SDA Slave
Address
S
S
T
A
R
T
R/W="0"
A
C
K
Sub
Address(n) A
C
K
Data(n)
A
C
K
Data(n+1)
A
C
K
A
C
K
Data(n+x)
A
C
K
P
S
T
O
P
Figure 38. Data Transfer Sequence at the I2C-Bus Mode
0
0
1
0
0
CAD1
CAD0
R/W
(CAD1 and CAD0 are determined by pin settings)
Figure 39. The First Byte
0
0
0
A4
A3
A2
A1
A0
Figure 40. The Second Byte
D7
D6
D5
D4
D3
D2
D1
D0
Figure 41. Byte Structure After The Second Byte
[AK4438]
016001925-E-00 2016/03
- 50 -
(2)-2. READ Operations
Set the R/W bit = “1” for the READ operation of the AK4438. After transmission of data, the master can
read the next address’s data by generating an acknowledge instead of terminating the write cycle after
the receipt of the first data word. After receiving each data packet the internal address counter is
incremented by one, and the next data is automatically taken into the next address. If the address
exceeds “14H” prior to generating stop condition, the address counter will “roll over” to “00H” and the data
of “00H” will be read out.
The AK4438 supports two basic read operations: Current Address Read and Random Address Read.
(2)-2-1. Current Address Read
The AK4438 contains an internal address counter that maintains the address of the last word accessed,
incremented by one. Therefore, if the last access (either a read or write) was to address “n”, the next
CURRENT READ operation would access data from the address “n+1”. After receipt of the slave address
with R/W bit “1”, the AK4438 generates an acknowledge, transmits 1-byte of data to the address set by
the internal address counter and increments the internal address counter by 1. If the master does not
generate an acknowledge but generates a stop condition instead, the AK4438 ceases transmission.
SDA Slave
Address
S
S
T
A
R
T
R/W="1"
A
C
K
A
C
K
Data(n+1)
A
C
K
Data(n+2)
A
C
K
A
C
K
Data(n+x)
N
A
C
K
P
S
T
O
P
Data(n)
M
A
S
T
E
R
M
A
S
T
E
R
M
A
S
T
E
R
M
A
S
T
E
R
M
A
S
T
E
R
Figure 42. Current Address Read
(2)-2-2. Random Address Read
The random read operation allows the master to access any memory location at random. Prior to issuing
a slave address with the R/W bit =“1”, the master must execute a “dummy” write operation first. The
master issues a start request, a slave address (R/W bit = “0”) and then the register address to read. After
the register address is acknowledged, the master immediately reissues the start request and the slave
address with the R/W bit =“1”. The AK4438 then generates an acknowledge, 1 byte of data and
increments the internal address counter by 1. If the master does not generate an acknowledge but
generates a stop condition instead, the AK4438 ceases transmission.
SDA Slave
Address
S
S
T
A
R
T
R/W="0"
A
C
K
A
C
K
A
C
K
Data(n)
A
C
K
Data(n+x)
A
C
K
P
S
T
O
P
Sub
Address(n) SSlave
Address
R/W="1"
S
T
A
R
T
Data(n+1)
A
C
K
N
A
C
K
M
A
S
T
E
R
M
A
S
T
E
R
M
A
S
T
E
R
M
A
S
T
E
R
Figure 43. Random Address Read
[AK4438]
016001925-E-00 2016/03
- 51 -
SCL
SDA
stop condition
start condition
S
P
Figure 44. START and STOP Conditions
SCL FROM
MASTER
acknowledge
DATA
OUTPUT BY
TRANSMITTER
DATA
OUTPUT BY
RECEIVER
1
9
8
START
CONDITION
not acknowledge
clock pulse for
acknowledgement
S
2
Figure 45. Acknowledge on the I2C-Bus
SCL
SDA
data line
stable;
data valid
change
of data
allowed
Figure 46. Bit Transfer on the I2C-Bus
[AK4438]
016001925-E-00 2016/03
- 52 -
■ Register Map
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
00H
Control 1
ACKS
0
0
0
DIF2
DIF1
DIF0
RSTN
01H
Control 2
0
0
SD
DFS1
DFS0
DEM11
DEM10
SMUTE
02H
Control 3
0
0
0
0
MONO1
DZFB
SELLR1
SLOW
03H
L1ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
04H
R1ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
05H
Control 4
INVL1
INVR1
INVL2
INVR2
SELLR2
0
DFS2
SSLOW
06H
-
0
0
0
0
0
0
0
0
07H
Control 6
L3
R3
L4
R4
0
0
0
SYNCE
08H
Control 7
L1
R1
L2
R2
0
0
0
0
09H
-
0
0
0
0
0
0
0
0
0AH
Control 8
TDM1
TDM0
SDS1
SDS2
PW2
PW1
DEM21
DEM20
0BH
Control 9
ATS1
ATS0
0
SDS0
PW4
PW3
0
0
0CH
Control 10
INVR4
INVL4
INVR3
INVL3
0
0
0
0
0DH
Control 11
MONO4
MONO3
MONO2
0
SELLR4
SELLR3
0
0
0EH
Control 12
DEM41
DEM40
DEM31
DEM30
0
0
0
0
0FH
L2ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
10H
R2ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
11H
L3ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
12H
R3ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
13H
L4ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
14H
R4ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
Notes: Data must not be written into addresses from 15H to 1FH.
The bit defined as 0 must contain a “0” value.
When the PDN pin goes to “L”, the registers are initialized to their default values.
When RSTN bit goes to “0”, the internal timing is reset, but registers are not initialized.
[AK4438]
016001925-E-00 2016/03
- 53 -
■ Register Definitions
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
00H
Control 1
ACKS
0
0
0
DIF2
DIF1
DIF0
RSTN
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
1
1
0
1
RSTN: Internal Timing Reset
0: Reset The DZF pin goes “H” but register values are not initialized.
1: Normal Operation (default)
DIF2-0: Audio Data Interface Modes (Table 9)
Default value is “110” (Mode 6: 32-bit MSB justified).
ACKS: Master Clock Frequency Auto Setting Mode Enable
0: Disable, Manual Setting Mode (default)
1: Enable, Auto Setting Mode
When ACKS bit = “1”, the MCLK frequency is detected automatically.
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
01H
Control 2
0
0
SD
DFS1
DFS0
DEM11
DEM10
SMUTE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
1
0
0
0
1
0
SMUTE: Soft Mute Enable.
0: Normal Operation (default)
1: DAC outputs soft-muted.
DEM11-0: DAC1 De-emphasis Response (Table 8)
Default value is “01” (OFF).
DFS2-0: Sampling Speed Control (Table 1)
Default value is “000” (Normal Speed).
A click noise occurs when switching DFS2-0 bits setting.
SD: Short delay Filter Enable. (Table 11)
0: Sharp roll off filter or Slow roll off filter
1: Short delay Sharp roll off filter or Short delay Slow roll off filter (default)
[AK4438]
016001925-E-00 2016/03
- 54 -
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
02H
Control 3
0
0
0
0
MONO1
DZFB
SELLR1
SLOW
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
SLOW: Slow Roll-off Filter Enable (Table 11)
0: Sharp Roll-off Filter (default)
1: Slow Roll-off Filter
SELLR1: The data selection of DAC1 (Table 15)
Default value is “0”
DZB: Inverting Enable of DZF (Table 12)
0: DZF pin goes “H” at Zero Detection (default)
1: DZF pin goes “L” at Zero Detection
MONO1: DAC1 enters monaural output mode when MONO bit = “1” (Table 15).
0: Stereo mode (default)
1: MONO mode
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
03H
L1ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
04H
R1ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
1
1
1
1
1
1
1
1
ATT7-0: Attenuation Level (Table 13)
Default value is “FF” (0dB)
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
05H
Control 4
INVL1
INVR1
INVL2
INVR2
SELLR2
0
DFS2
SSLOW
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
SSLOW: Digital Filter bypass mode Enable (Table 11)
0: Disable (default)
1: Enable
DFS2-0: Sampling Speed Control (Table 1)
Default value is “000” (Normal Speed).
A click noise occurs when switching DFS2-0 bits setting.
SELLR2: The data selection of DAC2 (Table 16)
Default value is “0”
INVL1: AOUTL1 Output Phase Inverting Bit (Table 15)
INVR1: AOUTR1 Output Phase Inverting Bit (Table 15)
INVL2: AOUTL2 Output Phase Inverting Bit (Table 16)
INVR2: AOUTR2 Output Phase Inverting Bit (Table 16)
0: Normal (default)
1: Inverted
[AK4438]
016001925-E-00 2016/03
- 55 -
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
07H
Control 6
L3
R3
L4
R4
0
0
0
SYNCE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
1
SYNCE: SYNC Mode Enable
0: SYNC Mode Disable
1: SYNC Mode Enable (default)
L3-4, R3-4: Zero Detect Flag Enable Bit for the DZF pin
0: Disable(default)
1: Enable
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
08H
Control 7
L1
R1
L2
R2
0
0
0
0
R/W
R/W
R/W
RD
RD
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
L1-2, R1-2: Zero Detect Flag Enable Bit for the DZF pin
0: Disable(default)
1: Enable
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0AH
Control 8
TDM1
TDM0
SDS1
SDS2
PW2
PW1
DEM21
DEM20
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
1
1
0
1
DEM21-20: DAC2 De-emphasis Response (Table 8)
Default value is “01”. (OFF)
PW2-1: Power Down control for DAC
PW2: Power management for DAC2
0: DAC2 power OFF
1: DAC2 power ON (default)
PW1: Power management for DAC1
0: DAC1 power OFF
1: DAC1 power ON (default)
SDS2-0: DAC1-4 Data Select
0: Normal Operation
1: Output Other Slot Data (Table 10)
Default value is “000”.
TDM1-0: TDM Mode Select (Table 9)
Default value is “00”.
[AK4438]
016001925-E-00 2016/03
- 56 -
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0BH
Control 9
ATS1
ATS0
0
SDS0
PW4
PW3
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
1
1
0
0
PW4-3: Power Down control for DAC
PW4: Power management for DAC4
0: DAC4 power OFF
1: DAC4 power ON (default)
PW3: Power management for DAC3
0: DAC3 power OFF
1: DAC3 power ON (default)
SDS2-0: DAC1-4 Data Select
0: Normal Operation
1: Output Other Slot Data (Table 10)
The default value is “000”.
ATS1-0: Transition Time between Set Values of ATT7-0 bits (Table 14)
The default value is “00”.
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0CH
Control 6
INVR4
INVL4
INVR3
INVL3
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
INVL3: AOUTL3 Output Phase Inverting Bit (Table 17)
INVR3: AOUTR3 Output Phase Inverting Bit (Table 17)
INVL4: AOUTL4 Output Phase Inverting Bit (Table 18)
INVR4: AOUTR4 Output Phase Inverting Bit (Table 18)
0: Normal (default)
1: Inverted
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0DH
Control 6
MONO4
MONO3
MONO2
0
SELLR4
SELLR3
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
SELLR3: The data selection of DAC3 (Table 17)
SELLR4: The data selection of DAC4 (Table 18)
The default value is “0”.
MONO2: DAC2 enters Mono output mode when MONO2 bit =“1”. (Table 16)
MONO3: DAC3 enters Mono output mode when MONO3 bit =“1”. (Table 17)
MONO4: DAC4 enters Mono output mode when MONO4 bit =“1”. (Table 18)
0: Stereo mode (default)
1: MONO mode
[AK4438]
016001925-E-00 2016/03
- 57 -
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0EH
Control 6
DEM41
DEM40
DEM31
DEM30
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
1
0
1
0
0
0
0
DEM31-30: DAC3 De-emphasis Response (Table 8)
DEM41-40: DAC4 De-emphasis Response (Table 8)
The default value is “01”, OFF
Addr
Register Name
D7
D6
D5
D4
D3
D2
D1
D0
0FH
L2ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
10H
R2ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
11H
L3ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
12H
R3ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
13H
L4ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
14H
R4ch ATT
ATT7
ATT6
ATT5
ATT4
ATT3
ATT2
ATT1
ATT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
1
1
1
1
1
1
1
1
ATT7-0: Attenuation Level (Table 13)
The default value is “FF”, (0dB)
[AK4438]
016001925-E-00 2016/03
- 58 -
13. Recommended External Circuits
■ Typical Connection Diagram
DSP
P
Power Supply
1.7 3.6V
AOUTR3
AOUTL4
AOUTR4
TEST
I2C
TVDD
VSS1
AOUTL3
AVDD
VSS2
VCOM
VREFL
AOUTL2
BICK
LRCK
SDTI1
SDTI2
SDTI3
SDTI4
DZF
AOUTR1
AOUTL1
PS/CAD0_SPI
CAD0_I2C/CSN/DIF
SCL/CCLK/TDM1
SDA/CDTI/TDM0
SMUTE/CAD1
PDN
AK4438
Top View
25
26
27
28
29
30
31
24
23
16
15
14
13
12
11
10
9
22
21
20
19
18
1
2
3
4
5
6
7
8
32
17
VREFH
AOUTR2
LDOO
Power Supply
3.0 3.6V
2.2u
MCLK
+
0.1u
10u
+
10u
0.1u
2.2u
H : I2C
L : SPI
L1ch out
R1ch out
L2ch out
R2ch out
L3ch out
R3ch out
L4ch out
R4ch out
+
0.1u
10u
Analog Ground
Digital Ground
Analog Ground
Digital Ground
Figure 47. Typical Connection Diagram
Note: The AK4438 integrates smoothing filters.
[AK4438]
016001925-E-00 2016/03
- 59 -
1. Grounding and Power Supply Decoupling
The AK4438 requires careful attention to power supply and grounding arrangements. AVDD and TVDD
are usually supplied from the analog supply of the system. If AVDD and TVDD are supplied separately,
the power-up sequences between AVDD and TVDD is not critical. VSS1 and VSS2 must be connected
to the same analog ground plane. System analog ground and digital ground should be wired separately
and connected together as close as possible to where the supplies are brought onto the printed circuit
board. Decoupling capacitors should be as near to the AK4438 as possible.
2. Voltage Reference
The differential voltage between VREFH pin and VREFL pin sets the analog output range. The VREFH
pin is normally connected to AVDD, and the VREFL pin is normally connected to VSS2. VREFHL and
VREFL should be connected with a 0.1µF ceramic capacitor and 10µF electrolytic capacitor as near as
possible to the pin to eliminate the effects of high frequency noise.
VCOM is a signal ground of this chip and output the voltage AVDDx1/2. A 2.2F ±50% ceramic capacitor
attached between the VCOM pin and VSS2 eliminates the effects of high frequency noise. This capacitor
should be as close to the pin as possible. No load current may be drawn from the VCOM pin. All signals,
especially clocks, should be kept away from the VREFH pin and the VCOM pin in order to avoid unwanted
coupling into the AK4438.
LDOO outputs 1.2V that is used for internal digital circuit. LDOO and VSS1 should be connected with a
2.2F ±50% ceramic capacitor as near as possible to the pin to stabilize internal LDO. No load current
may be drawn from the VCOM pin.
3. Analog Output
The output signal range is nominally 0.86 x VREFH Vpp centered around the VCOM voltage. The DAC
input data format is 2’s complement. The output voltage is a positive full scale for 7FFFFFFFH (@32bit)
and a negative full scale for 80000000H (@32bit). The ideal output is VCOM voltage for 00000000H
(@32bit). The internal analog filters remove most of the noise generated by the delta-sigma modulator of
DAC beyond the audio passband, in single-ended input mode.
Normally, DC component is cut by an external capacitor since the DAC outputs have DC offsets of a few
millivolts to the VCOM voltage.
[AK4438]
016001925-E-00 2016/03
- 60 -
4. External Analog Outputs Circuit
The output level of this circuit is 2.83Vpp (AK4438: typ. 2.83Vpp). Normally, DC component is cut by an
external capacitor since the DAC outputs have DC offsets of a few millivolts to the VCOM voltage. The
cutoff frequency of HPF is shown below.
fc= 1/(2 × π × R × C) [Hz]
Where the C is the external AC coupling capacitor and the R is load resistance.
When C = 1μF and R = 10kΩ, then fs = 16Hz.
AK4438
AOUT
Analog Out
R=10k
2.83Vppv (typ)
C=1F
Figure 48. Output Buffer Circuit Example
[AK4438]
016001925-E-00 2016/03
- 61 -
14. Package
■ Outline Dimensions
32-pin QFN (Unit: mm)
■ Material & Lead Finish
Package molding compound: Epoxy, Halogen (Br and Cl) free
Lead frame material: Cu
Terminal surface treatment: Solder (Pb free) plate
[AK4438]
016001925-E-00 2016/03
- 62 -
■ Marking
4438
XXXX
1
1) Pin #1 indication
2) Date Code: XXXX (4 digits)
3) Marking Code: 4438
15. Ordering Guide
■ Ordering Guide
AK4438VN -40 +105C 32-pin QFN (0.5mm pitch)
AKD4438 Evaluation Board for the AK4438
16. Revision History
Date (Y/M/D)
Revision
Reason
Page
Contents
16/03/04
00
First Edition
[AK4438]
016001925-E-00 2016/03
- 63 -
IMPORTANT NOTICE
0. Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to the
information contained in this document without notice. When you consider any use or application
of AKM product stipulated in this document (“Product”), please make inquiries the sales office of
AKM or authorized distributors as to current status of the Products.
1. All information included in this document are provided only to illustrate the operation and
application examples of AKM Products. AKM neither makes warranties or representations with
respect to the accuracy or completeness of the information contained in this document nor
grants any license to any intellectual property rights or any other rights of AKM or any third party
with respect to the information in this document. You are fully responsible for use of such
information contained in this document in your product design or applications. AKM ASSUMES
NO LIABILITY FOR ANY LOSSES INCURRED BY YOU OR THIRD PARTIES ARISING FROM
THE USE OF SUCH INFORMATION IN YOUR PRODUCT DESIGN OR APPLICATIONS.
2. The Product is neither intended nor warranted for use in equipment or systems that require
extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may
cause loss of human life, bodily injury, serious property damage or serious public impact,
including but not limited to, equipment used in nuclear facilities, equipment used in the
aerospace industry, medical equipment, equipment used for automobiles, trains, ships and
other transportation, traffic signaling equipment, equipment used to control combustions or
explosions, safety devices, elevators and escalators, devices related to electric power, and
equipment used in finance-related fields. Do not use Product for the above use unless
specifically agreed by AKM in writing.
3. Though AKM works continually to improve the Product’s quality and reliability, you are
responsible for complying with safety standards and for providing adequate designs and
safeguards for your hardware, software and systems which minimize risk and avoid situations in
which a malfunction or failure of the Product could cause loss of human life, bodily injury or
damage to property, including data loss or corruption.
4. Do not use or otherwise make available the Product or related technology or any information
contained in this document for any military purposes, including without limitation, for the design,
development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or
missile technology products (mass destruction weapons). When exporting the Products or
related technology or any information contained in this document, you should comply with the
applicable export control laws and regulations and follow the procedures required by such laws
and regulations. The Products and related technology may not be used for or incorporated into
any products or systems whose manufacture, use, or sale is prohibited under any applicable
domestic or foreign laws or regulations.
5. Please contact AKM sales representative for details as to environmental matters such as the
RoHS compatibility of the Product. Please use the Product in compliance with all applicable laws
and regulations that regulate the inclusion or use of controlled substances, including without
limitation, the EU RoHS Directive. AKM assumes no liability for damages or losses occurring as
a result of noncompliance with applicable laws and regulations.
6. Resale of the Product with provisions different from the statement and/or technical features set
forth in this document shall immediately void any warranty granted by AKM for the Product and
shall not create or extend in any manner whatsoever, any liability of AKM.
7. This document may not be reproduced or duplicated, in any form, in whole or in part, without
prior written consent of AKM.
