M PICmicroTM Mid-Range MCU Family Reference Manual 1997 Microchip Technology Inc. December 1997 /DS33023A M Internationally Recognized Quality System Certifications Microchip's Quality System embodies the requirements of ISO9001:1994. Our Microchip Chandler and Tempe Design and Manufacturing facilities have been certified to ISO 9001. The Microchip Kaohsiung Test facility, and primary Assembly houses have been certified to ISO 9002. ISO certification plans are in-process for an estimated certification grant by year-end 1997. In addition, Microchip has received numerous customer certifications, including a Delco issued certificate of compliance to AEC-A100/QS9000. "All rights reserved. Copyright (c) 1997, Microchip Technology Incorporated, USA. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights." December 1997 /DS33023A Microchip received ISO 9001 Quality System certification for its worldwide headquarters, design, and wafer fabrication facilities in January, 1997. Our field-programmable PICmicroTM 8-bit MCUs, Serial EEPROMs, related specialty memory products and development systems conform to the stringent quality standards of the International Standard Organization (ISO). Trademarks The Microchip name, logo, PIC, KEELOQ, PICMASTER, PICSTART, PRO MATE, and SEEVAL are registered trademarks of Microchip Technology Incorporated in the U.S.A. MPLAB, PICmicro, ICSP and In-Circuit Serial Programming are trademarks of Microchip Technology Incorporated. Serialized Quick-Turn Production is a Service Mark of Microchip Technology Incorporated. All other trademarks mentioned herein are property of their respective companies. 1997 Microchip Technology Inc. M Table of Contents PAGE SECTION 1. INTRODUCTION 1-1 Introduction .......................................................................................................................................................1-2 Manual Objective ..............................................................................................................................................1-3 Device Structure ...............................................................................................................................................1-4 Development Support .......................................................................................................................................1-6 Device Varieties ...............................................................................................................................................1-7 Style and Symbol Conventions ......................................................................................................................1-12 Related Documents ........................................................................................................................................1-14 Related Application Notes ..............................................................................................................................1-17 Revision History .............................................................................................................................................1-18 SECTION 2. OSCILLATOR 2-1 Introduction .......................................................................................................................................................2-2 Oscillator Configurations ..................................................................................................................................2-2 Crystal Oscillators / Ceramic Resonators .........................................................................................................2-4 External RC Oscillator ....................................................................................................................................2-12 Internal 4 MHz RC Oscillator ..........................................................................................................................2-13 Effects of Sleep Mode on the On-chip Oscillator ............................................................................................2-17 Effects of Device Reset on the On-chip Oscillator .........................................................................................2-17 Design Tips ....................................................................................................................................................2-18 Related Application Notes ..............................................................................................................................2-19 Revision History .............................................................................................................................................2-20 SECTION 3. RESET 3-1 Introduction .......................................................................................................................................................3-2 Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST), Brown-out Reset (BOR), and Parity Error Reset (PER) ..............................3-4 Registers and Status Bit Values .....................................................................................................................3-10 Design Tips ....................................................................................................................................................3-16 Related Application Notes ..............................................................................................................................3-17 Revision History .............................................................................................................................................3-18 SECTION 4. ARCHITECTURE 4-1 Introduction .......................................................................................................................................................4-2 Clocking Scheme/Instruction Cycle ..................................................................................................................4-5 Instruction Flow/Pipelining ................................................................................................................................4-6 I/O Descriptions ................................................................................................................................................4-7 Design Tips ....................................................................................................................................................4-12 Related Application Notes ..............................................................................................................................4-13 Revision History .............................................................................................................................................4-14 1997 Microchip Technology Inc. DS00097D-page iii M Table of Contents PAGE SECTION 5. CPU AND ALU 5-1 Introduction .......................................................................................................................................................5-2 General Instruction Format ...............................................................................................................................5-4 Central Processing Unit (CPU) .........................................................................................................................5-4 Instruction Clock ...............................................................................................................................................5-4 Arithmetic Logical Unit (ALU) ...........................................................................................................................5-5 STATUS Register .............................................................................................................................................5-6 OPTION_REG Register ...................................................................................................................................5-8 PCON Register .................................................................................................................................................5-9 Design Tips ....................................................................................................................................................5-10 Related Application Notes ..............................................................................................................................5-11 Revision History .............................................................................................................................................5-12 SECTION 6. MEMORY ORGANIZATION 6-1 Introduction .......................................................................................................................................................6-2 Program Memory Organization ........................................................................................................................6-2 Data Memory Organization ..............................................................................................................................6-8 Initialization .....................................................................................................................................................6-14 Design Tips ....................................................................................................................................................6-16 Related Application Notes ..............................................................................................................................6-17 Revision History .............................................................................................................................................6-18 SECTION 7. DATA EEPROM 7-1 Introduction .......................................................................................................................................................7-2 Control Register ...............................................................................................................................................7-3 EEADR .............................................................................................................................................................7-4 EECON1 and EECON2 Registers ....................................................................................................................7-4 Reading the EEPROM Data Memory ...............................................................................................................7-5 Writing to the EEPROM Data Memory .............................................................................................................7-5 Write Verify .......................................................................................................................................................7-6 Protection Against Spurious Writes ..................................................................................................................7-7 Data EEPROM Operation During Code Protected Configuration ....................................................................7-7 Initialization .......................................................................................................................................................7-7 Design Tips ......................................................................................................................................................7-8 Related Application Notes ................................................................................................................................7-9 Revision History .............................................................................................................................................7-10 SECTION 8. INTERRUPTS 8-1 Introduction .......................................................................................................................................................8-2 Control Registers ..............................................................................................................................................8-5 Interrupt Latency ............................................................................................................................................8-10 INT and External Interrupts ............................................................................................................................8-10 Context Saving During Interrupts ...................................................................................................................8-11 Initialization .....................................................................................................................................................8-14 Design Tips ....................................................................................................................................................8-16 Related Application Notes ..............................................................................................................................8-17 Revision History .............................................................................................................................................8-18 DS00097D-page iv 1997 Microchip Technology Inc. M Table of Contents PAGE SECTION 9. I/O PORTS 9-1 Introduction .......................................................................................................................................................9-2 PORTA and the TRISA Register ......................................................................................................................9-4 PORTB and the TRISB Register ......................................................................................................................9-6 PORTC and the TRISC Register ......................................................................................................................9-8 PORTD and the TRISD Register ......................................................................................................................9-9 PORTE and the TRISE Register ....................................................................................................................9-10 PORTF and the TRISF Register ....................................................................................................................9-11 PORTG and the TRISG Register ...................................................................................................................9-12 GPIO and the TRISGP Register .....................................................................................................................9-13 I/O Programming Considerations ...................................................................................................................9-14 Initialization .....................................................................................................................................................9-16 Design Tips ....................................................................................................................................................9-17 Related Application Notes ..............................................................................................................................9-19 Revision History .............................................................................................................................................9-20 SECTION 10. PARALLEL SLAVE PORT 10-1 Introduction .....................................................................................................................................................10-2 Control Register .............................................................................................................................................10-3 Operation ........................................................................................................................................................10-4 Operation in Sleep Mode ................................................................................................................................10-5 Effect of a Reset .............................................................................................................................................10-5 PSP Waveforms .............................................................................................................................................10-5 Design Tips ....................................................................................................................................................10-6 Related Application Notes ..............................................................................................................................10-7 Revision History .............................................................................................................................................10-8 1997 Microchip Technology Inc. DS00097D-page v M Table of Contents PAGE SECTION 11. TIMER0 11-1 Introduction .....................................................................................................................................................11-2 Control Register .............................................................................................................................................11-3 Operation ........................................................................................................................................................11-4 TMR0 Interrupt ...............................................................................................................................................11-5 Using Timer0 with an External Clock .............................................................................................................11-6 TMR0 Prescaler .............................................................................................................................................11-7 Design Tips ..................................................................................................................................................11-10 Related Application Notes ............................................................................................................................11-11 Revision History ...........................................................................................................................................11-12 SECTION 12. TIMER1 12-1 Introduction .....................................................................................................................................................12-2 Control Register .............................................................................................................................................12-3 Timer1 Operation in Timer Mode ...................................................................................................................12-4 Timer1 Operation in Synchronized Counter Mode .........................................................................................12-4 Timer1 Operation in Asynchronous Counter Mode ........................................................................................12-5 Timer1 Oscillator ............................................................................................................................................12-7 Sleep Operation .............................................................................................................................................12-9 Resetting Timer1 Using a CCP Trigger Output ..............................................................................................12-9 Resetting of Timer1 Register Pair (TMR1H:TMR1L) ......................................................................................12-9 Timer1 Prescaler ............................................................................................................................................12-9 Initialization ...................................................................................................................................................12-10 Design Tips ..................................................................................................................................................12-12 Related Application Notes ............................................................................................................................12-13 Revision History ...........................................................................................................................................12-14 SECTION 13. TIMER2 13-1 Introduction .....................................................................................................................................................13-2 Control Register .............................................................................................................................................13-3 Timer Clock Source ........................................................................................................................................13-4 Timer (TMR2) and Period (PR2) Registers ....................................................................................................13-4 TMR2 Match Output .......................................................................................................................................13-4 Clearing the Timer2 Prescaler and Postscaler ...............................................................................................13-4 Sleep Operation .............................................................................................................................................13-4 Initialization .....................................................................................................................................................13-5 Design Tips ....................................................................................................................................................13-6 Related Application Notes ..............................................................................................................................13-7 Revision History .............................................................................................................................................13-8 SECTION 14. COMPARE/CAPTURE/PWM (CCP) 14-1 Introduction .....................................................................................................................................................14-2 Control Register .............................................................................................................................................14-3 Capture Mode .................................................................................................................................................14-4 Compare Mode ...............................................................................................................................................14-6 PWM Mode .....................................................................................................................................................14-8 Initialization ...................................................................................................................................................14-12 Design Tips ..................................................................................................................................................14-15 Related Application Notes ............................................................................................................................14-17 Revision History ...........................................................................................................................................14-18 DS00097D-page vi 1997 Microchip Technology Inc. M Table of Contents PAGE SECTION 15. SYNCHRONOUS SERIAL PORT (SSP) 15-1 Introduction .....................................................................................................................................................15-2 Control Registers ............................................................................................................................................15-3 SPI Mode ........................................................................................................................................................15-6 SSP I2C Operation .......................................................................................................................................15-16 Initialization ...................................................................................................................................................15-26 Design Tips ..................................................................................................................................................15-28 Related Application Notes ............................................................................................................................15-29 Revision History ...........................................................................................................................................15-30 SECTION 16. BASIC SYCHRONOUS SERIAL PORT (BSSP) 16-1 Introduction .....................................................................................................................................................16-2 Control Registers ............................................................................................................................................16-3 SPI Mode ........................................................................................................................................................16-6 SSP I2C Operation .......................................................................................................................................16-15 Initialization ...................................................................................................................................................16-23 Design Tips ..................................................................................................................................................16-24 Related Application Notes ............................................................................................................................16-25 Revision History ...........................................................................................................................................16-26 SECTION 17. MASTER SYNCHRONOUS SERIAL PORT (MSSP) 17-1 Introduction .....................................................................................................................................................17-2 Control Register .............................................................................................................................................17-4 SPI Mode ........................................................................................................................................................17-9 SSP I2CTM Operation ....................................................................................................................................17-18 Connection Considerations for I2C Bus ........................................................................................................17-56 Initialization ...................................................................................................................................................17-57 Design Tips ..................................................................................................................................................17-58 Related Application Notes ............................................................................................................................17-59 Revision History ...........................................................................................................................................17-60 SECTION 18. USART 18-1 Introduction .....................................................................................................................................................18-2 Control Registers ............................................................................................................................................18-3 USART Baud Rate Generator (BRG) .............................................................................................................18-5 USART Asynchronous Mode .........................................................................................................................18-8 USART Synchronous Master Mode .............................................................................................................18-15 USART Synchronous Slave Mode ...............................................................................................................18-19 Initialization ...................................................................................................................................................18-21 Design Tips ..................................................................................................................................................18-22 Related Application Notes ............................................................................................................................18-23 Revision History ...........................................................................................................................................18-24 1997 Microchip Technology Inc. DS00097D-page vii M Table of Contents PAGE SECTION 19. VOLTAGE REFERENCE 19-1 Introduction .....................................................................................................................................................19-2 Control Register .............................................................................................................................................19-3 Configuring the Voltage Reference ................................................................................................................19-4 Voltage Reference Accuracy/Error .................................................................................................................19-5 Operation During Sleep ..................................................................................................................................19-5 Effects of a Reset ...........................................................................................................................................19-5 Connection Considerations ............................................................................................................................19-6 Initialization .....................................................................................................................................................19-7 Design Tips ....................................................................................................................................................19-8 Related Application Notes ..............................................................................................................................19-9 Revision History ...........................................................................................................................................19-10 SECTION 20. COMPARATOR 20-1 Introduction .....................................................................................................................................................20-2 Control Register .............................................................................................................................................20-3 Comparator Configuration ..............................................................................................................................20-4 Comparator Operation ....................................................................................................................................20-6 Comparator Reference ...................................................................................................................................20-6 Comparator Response Time ..........................................................................................................................20-8 Comparator Outputs .......................................................................................................................................20-8 Comparator Interrupts ....................................................................................................................................20-9 Comparator Operation During SLEEP ...........................................................................................................20-9 Effects of a RESET ........................................................................................................................................20-9 Analog Input Connection Considerations .....................................................................................................20-10 Initialization ...................................................................................................................................................20-11 Design Tips ..................................................................................................................................................20-12 Related Application Notes ............................................................................................................................20-13 Revision History ...........................................................................................................................................20-14 SECTION 21. 8-BIT A/D CONVERTER 21-1 Introduction .....................................................................................................................................................21-2 Control Registers ............................................................................................................................................21-3 Operation ........................................................................................................................................................21-5 A/D Acquisition Requirements ........................................................................................................................21-6 Selecting the A/D Conversion Clock ..............................................................................................................21-8 Configuring Analog Port Pins .........................................................................................................................21-9 A/D Conversions ..........................................................................................................................................21-10 A/D Operation During Sleep .........................................................................................................................21-12 A/D Accuracy/Error .......................................................................................................................................21-13 Effects of a RESET ......................................................................................................................................21-13 Use of the CCP Trigger ................................................................................................................................21-14 Connection Considerations ..........................................................................................................................21-14 Transfer Function .........................................................................................................................................21-14 Initialization ...................................................................................................................................................21-15 Design Tips ..................................................................................................................................................21-16 Related Application Notes ............................................................................................................................21-17 Revision History ...........................................................................................................................................21-18 DS00097D-page viii 1997 Microchip Technology Inc. M Table of Contents PAGE SECTION 22. BASIC 8-BIT A/D CONVERTER 22-1 Introduction .....................................................................................................................................................22-2 Control Registers ............................................................................................................................................22-3 A/D Acquisition Requirements ........................................................................................................................22-6 Selecting the A/D Conversion Clock ..............................................................................................................22-8 Configuring Analog Port Pins .......................................................................................................................22-10 A/D Conversions ..........................................................................................................................................22-11 A/D Operation During Sleep .........................................................................................................................22-14 A/D Accuracy/Error .......................................................................................................................................22-15 Effects of a RESET ......................................................................................................................................22-16 Connection Considerations ..........................................................................................................................22-16 Transfer Function .........................................................................................................................................22-16 Initialization ...................................................................................................................................................22-17 Design Tips ..................................................................................................................................................22-18 Related Application Notes ............................................................................................................................22-19 Revision History ...........................................................................................................................................22-20 SECTION 23. 10-BIT A/D CONVERTER 23-1 Introduction .....................................................................................................................................................23-2 Control Register .............................................................................................................................................23-3 Operation ........................................................................................................................................................23-5 A/D Acquisition Requirements ........................................................................................................................23-6 Selecting the A/D Conversion Clock ..............................................................................................................23-8 Configuring Analog Port Pins .........................................................................................................................23-9 A/D Conversions ..........................................................................................................................................23-10 Operation During Sleep ................................................................................................................................23-14 Effects of a Reset .........................................................................................................................................23-14 A/D Accuracy/Error .......................................................................................................................................23-15 Connection Considerations ..........................................................................................................................23-16 Transfer Function .........................................................................................................................................23-16 Initialization ...................................................................................................................................................23-17 Design Tips ..................................................................................................................................................23-18 Related Application Notes ............................................................................................................................23-19 Revision History ...........................................................................................................................................23-20 SECTION 24. SLOPE A/D 24-1 Introduction .....................................................................................................................................................24-2 Control Registers ............................................................................................................................................24-3 Conversion Process .......................................................................................................................................24-6 Other Analog Modules ..................................................................................................................................24-12 Calibration Parameters .................................................................................................................................24-13 Design Tips ..................................................................................................................................................24-14 Related Application Notes ............................................................................................................................24-15 Revision History ...........................................................................................................................................24-16 1997 Microchip Technology Inc. DS00097D-page ix M Table of Contents PAGE SECTION 25. LCD 25-1 Introduction .....................................................................................................................................................25-2 Control Register .............................................................................................................................................25-3 LCD Timing ....................................................................................................................................................25-6 LCD Interrupts ..............................................................................................................................................25-12 Pixel Control .................................................................................................................................................25-13 Voltage Generation ......................................................................................................................................25-15 Operation During Sleep ................................................................................................................................25-16 Effects of a Reset .........................................................................................................................................25-17 Configuring the LCD Module ........................................................................................................................25-17 Discrimination Ratio .....................................................................................................................................25-18 LCD Voltage Generation ..............................................................................................................................25-20 Contrast ........................................................................................................................................................25-22 LCD Glass ....................................................................................................................................................25-22 Initialization ...................................................................................................................................................25-23 Design Tips ..................................................................................................................................................25-24 Related Application Notes ............................................................................................................................25-25 Revision History ...........................................................................................................................................25-26 SECTION 26. WATCHDOG TIMER AND SLEEP MODE 26-1 Introduction .....................................................................................................................................................26-2 Control Register .............................................................................................................................................26-3 Watchdog Timer (WDT) Operation .................................................................................................................26-4 SLEEP (Power-Down) Mode ..........................................................................................................................26-7 Initialization .....................................................................................................................................................26-9 Design Tips ..................................................................................................................................................26-10 Related Application Notes ............................................................................................................................26-11 Revision History ...........................................................................................................................................26-12 SECTION 27. DEVICE CONFIGURATION BITS 27-1 Introduction .....................................................................................................................................................27-2 Configuration Word Bits .................................................................................................................................27-4 Program Verification/Code Protection ............................................................................................................27-8 ID Locations ...................................................................................................................................................27-9 Design Tips ..................................................................................................................................................27-10 Related Application Notes ............................................................................................................................27-11 Revision History ...........................................................................................................................................27-12 SECTION 28. IN-CIRCUIT SERIAL PROGRAMMINGTM 28-1 Introduction .....................................................................................................................................................28-2 Entering In-Circuit Serial Programming Mode ................................................................................................28-3 Application Circuit ...........................................................................................................................................28-4 Programmer ...................................................................................................................................................28-6 Programming Environment .............................................................................................................................28-6 Other Benefits ................................................................................................................................................28-7 Field Programming of PICmicro OTP MCUs ..................................................................................................28-8 Field Programming of FLASH PICmicros .....................................................................................................28-10 Design Tips ..................................................................................................................................................28-12 Related Application Notes ............................................................................................................................28-13 Revision History ...........................................................................................................................................28-14 DS00097D-page x 1997 Microchip Technology Inc. M Table of Contents PAGE SECTION 29. INSTRUCTION SET 29-1 Introduction .....................................................................................................................................................29-2 Instruction Formats .........................................................................................................................................29-4 Special Function Registers as Source/Destination ........................................................................................29-6 Q Cycle Activity ..............................................................................................................................................29-7 Instruction Descriptions ..................................................................................................................................29-8 Design Tips ..................................................................................................................................................29-45 Related Application Notes ............................................................................................................................29-47 Revision History ...........................................................................................................................................29-48 SECTION 30. ELECTRICAL SPECIFICATIONS 30-1 Introduction .....................................................................................................................................................30-2 Absolute Maximums .......................................................................................................................................30-3 Device Selection Table ...................................................................................................................................30-4 Device Voltage Specifications ........................................................................................................................30-5 Device Current Specifications ........................................................................................................................30-6 Input Threshold Levels ...................................................................................................................................30-9 I/O Current Specifications ............................................................................................................................30-10 Output Drive Levels ......................................................................................................................................30-11 I/O Capacitive Loading .................................................................................................................................30-12 Data EEPROM / Flash .................................................................................................................................30-13 LCD ..............................................................................................................................................................30-14 Comparators and Voltage Reference ...........................................................................................................30-15 Timing Parameter Symbology ......................................................................................................................30-16 Example External Clock Timing Waveforms and Requirements ..................................................................30-17 Example Power-up and Reset Timing Waveforms and Requirements ........................................................30-19 Example Timer0 and Timer1 Timing Waveforms and Requirements ...........................................................30-20 Example CCP Timing Waveforms and Requirements .................................................................................30-21 Example Parallel Slave Port (PSP) Timing Waveforms and Requirements .................................................30-22 Example SSP and Master SSP SPI Mode Timing Waveforms and Requirements ......................................30-23 Example SSP I2C Mode Timing Waveforms and Requirements ..................................................................30-27 Example Master SSP I2C Mode Timing Waveforms and Requirements ......................................................30-30 Example USART/SCI Timing Waveforms and Requirements ......................................................................30-32 Example 8-bit A/D Timing Waveforms and Requirements ...........................................................................30-34 Example 10-bit A/D Timing Waveforms and Requirements .........................................................................30-36 Example Slope A/D Timing Waveforms and Requirements .........................................................................30-38 Example LCD Timing Waveforms and Requirements ..................................................................................30-40 Related Application Notes ............................................................................................................................30-41 Revision History ...........................................................................................................................................30-42 SECTION 31. DEVICE CHARACTERISTICS 31-1 Introduction .....................................................................................................................................................31-2 Characterization vs. Electrical Specification ...................................................................................................31-2 DC and AC Characteristics Graphs and Tables .............................................................................................31-2 Revision History ...........................................................................................................................................31-22 1997 Microchip Technology Inc. DS00097D-page xi M Table of Contents PAGE SECTION 32. DEVELOPMENT TOOLS 32-1 Introduction .....................................................................................................................................................32-2 The Integrated Development Environment (IDE) ...........................................................................................32-3 MPLAB Software Language Support .............................................................................................................32-6 MPLAB-SIM Simulator Software ....................................................................................................................32-8 MPLAB Emulator Hardware Support ..............................................................................................................32-9 MPLAB Programmer Support .......................................................................................................................32-10 Supplemental Tools ......................................................................................................................................32-11 Development Boards ....................................................................................................................................32-12 Development Tools for Other Microchip Products ........................................................................................32-14 Related Application Notes ............................................................................................................................32-15 Revision History ...........................................................................................................................................32-16 SECTION 33. CODE DEVELOPMENT 33-1 Revision History .............................................................................................................................................33-2 SECTION 34. APPENDIX 34-1 I2C Overview ...............................................................................................................................................34-2 List of LCD Glass Manufacturers ................................................................................................................. 34-11 Device Enhancement ...................................................................................................................................34-13 Revision History ........................................................................................................................................... 34-19 SECTION 35. GLOSSARY 35-1 Revision History ...........................................................................................................................................35-14 DS00097D-page xii 1997 Microchip Technology Inc. M 1 Introduction Section 1. Introduction HIGHLIGHTS This section of the manual contains the following major topics: 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Introduction ....................................................................................................................1-2 Manual Objective ...........................................................................................................1-3 Device Structure ............................................................................................................1-4 Development Support ....................................................................................................1-6 Device Varieties..............................................................................................................1-7 Style and Symbol Conventions ....................................................................................1-12 Related Documents .....................................................................................................1-14 Related Application Notes............................................................................................1-17 Revision History ...........................................................................................................1-18 1997 Microchip Technology Inc. DS31001A page 1-1 PICmicro MID-RANGE MCU FAMILY 1.1 Introduction Microchip is the Embedded Control Solutions Company. The company's focus is on products that meet the needs of the embedded control market. We are a leading supplier of: * * * * 8-bit General Purpose Microcontrollers (PICmicroTM MCUs) Speciality and standard non-volatile memory devices Security devices (KEELOQ(R)) Application specific standard products Please request a Microchip Product Line Card for a listing of all the interesting products that we have to offer. This literature can be obtained from your local sales office, or downloaded from the Microchip web site (www.microchip.com). In the past, 8-bit MCU users were fixed on the traditional MCU model for production, a ROM device was required. Microchip has been the leader in changing this perception by showing that OTP devices can give a better lifetime product cost compared to ROM versions. Microchip has a strength is in EPROM technology. That made it the memory technology of choice for the PICmicro MCU's program memory. Microchip has minimized the cost difference between EPROM and ROM memory technology, and therefore Microchip can pass these benefits onto our customers. This is not true for other MCU vendors, and is seen in the price difference between their EPROM and ROM versions. The growth of Microchip's 8-bit MCU market share is a testament to the PICmicro MCUs ability to meet the needs of many. This growth has made the PICmicro architecture one of the top three architectures available in the general market today. This growth was fueled by the Microchip vision of the benefits of a low cost OTP solution. Some of the benefits for the customer include: * * * * * * * Quick time to market Allows code changes to product, during production run No Non-Recurring Engineering (NRE) charges for Mask Revisions Ability to easily serialize the product Ability to store calibration data, without additional hardware Better able to maximize PICmicro MCU inventory Less risk, since the same device is used for development as well as for production. Microchip's PICmicro 8-bit MCUs offer a price/performance ratio that allows them to be considered for any traditional 8-bit MCU application as well as some traditional 4-bit applications (Base-Line family), dedicated logic replacement and low-end DSP applications (High-End family). These features and price-performance mix make PICmicro MCUs an attractive solution for most applications. DS31001A-page 1-2 1997 Microchip Technology Inc. Section 1. Introduction 1.2 1 Manual Objective 1. 2. 3. Base-Line: 12-bit Instruction Word length Mid-Range: 14-bit Instruction Word length High-End: 16-bit Instruction Word length This manual focuses on the Mid-Range devices, which are also referred to as the PIC16CXXX MCU family. The operation of the PIC16CXXX MCU family architecture and peripheral modules is explained, but does not cover the specifics of each device. Therefore, it is not intended to replace the device data sheets, but complement them. In other words, this guide supplies the general details and operation of the PICmicro architecture and peripheral modules, while the data sheet s give specific details such as device memory mapping. Initialization examples are given throughout this manual. These examples sometimes need to be written as device specific as opposed to family generic, though they are valid for most other devices. Some modifications may be required for devices with variations in register file mappings. Note: 1997 Microchip Technology Inc. The first few Mid-Range devices have minor device variations when compared to this general description. We have tried to describe these variations throughout this manual. Please refer to the specific device data sheet for complete information on the device. DS31001A-page 1-3 Introduction PICmicro devices are grouped by the size of their Instruction Word. The three current PICmicro families are: PICmicro MID-RANGE MCU FAMILY 1.3 Device Structure Each part of a device can be placed into one of three groups: 1. 2. 3. 1.3.1 Core Peripherals Special Features The Core The core pertains to the basic features that are required to make the device operate. These include: 1. 2. 3. 4. 5. 6. 7. 1.3.2 Device Oscillator Reset logic CPU (Central Processing Unit) operation ALU (Arithmetic Logical Unit) operation Device memory map organization Interrupt operation Instruction set Revision "DS31002A" Revision "DS31003A" Revision "DS31005A" Revision "DS31005A" Revision "DS31006A" Revision "DS31008A" Revision "DS31029A" Peripherals Peripherals are the features that add a differentiation from a microprocessor. These ease in interfacing to the external world (such as general purpose I/O, LCD drivers, A/D inputs, and PWM outputs), and internal tasks such as keeping different time bases (such as timers). The peripherals that are discussed are: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. DS31001A-page 1-4 General purpose I/O Timer0 Timer1 Timer2 Capture, Compare, and PWM (CCP) Synchronous Serial Port (SSP) Basic Synchronous Serial Port (SSP) Master Synchronous Serial Port (MSSP) USART (SCI) Voltage References Comparators 8-bit Analog to Digital (A/D) Basic 8-bit Analog to Digital (A/D) 10-bit Analog to Digital (A/D) Slope Analog to Digital (A/D) w/ Thermister Liquid Crystal Display (LCD) Drivers Parallel Slave Port (PSP) Revision "DS31009A" Revision "DS31011A" Revision "DS31012A" Revision "DS31013A" Revision "DS31014A" Revision "DS31015A" Revision "DS31016A" Revision "DS31017A" Revision "DS31018A" Revision "DS31019A" Revision "DS31020A" Revision "DS31021A" Revision "DS31022A" Revision "DS31023A" Revision "DS31024A" Revision "DS31025A" Revision "DS31010A" 1997 Microchip Technology Inc. Section 1. Introduction 1.3.3 1 Special Features * Decrease system cost * Increase system reliability * Increase design flexibility The Mid-Range PICmicro MCUs offer several features that help achieve these goals. The special features discussed are: 1. 2. 3. 4. 5. 6. 7. Device Configuration bits On-chip Power-on Reset (POR) Brown-out Reset (BOR) logic Watchdog Timer Low power mode (Sleep) Internal RC device oscillator In-Circuit Serial ProgrammingTM (ICSPTM) 1997 Microchip Technology Inc. Revision "DS31027A" Revision "DS31003A" Revision "DS31003A" Revision "DS31026A" Revision "DS31026A" Revision "DS31002A" Revision "DS31028A" DS31001A-page 1-5 Introduction Special features are the unique features that help to do one or more of the following things: PICmicro MID-RANGE MCU FAMILY 1.4 Development Support Microchip offers a wide range of development tools that allow users to efficiently develop and debug application code. Microchip's development tools can be broken down into four categories: 1. 2. 3. 4. Code generation Software debug Device programmer Product evaluation boards All tools developed by Microchip operate under the MPLABTM Integrated Development Environment (IDE), while some third party tools may not. The code generation tools include: * MPASM * MPLAB-C * MP-DriveWayTM These software development programs include device header files. Each header file defines the register names (as shown in the device data sheet) to the specified address or bit location. Using the header files eases code migration, and reduces the tediousness of memorizing a register's address or a bit's position in a register. Note: Microchip strongly recommends that the supplied header files be used in the source code of your program. This eases code migration as well as increases the quality and depth of the technical support that Microchip can offer. Tools which ease in debugging software are: * PICMASTER(R) In-Circuit Emulator * ICEPIC In-Circuit Emulator * MPLAB-SIM Software Simulator After generating and debugging the application software, the device will need to be programmed. Microchip offers two levels of programmers: 1. 2. PICSTART Plus programmer PROMATE II programmer Demonstration boards allow the developer of software code to evaluate the capability and suitability of the device to the application. The demo boards offered are: * * * * PICDEM-1 PICDEM-2 PICDEM-3 PICDEM-14A A full description of each of Microchip's development tools is discussed in the "Development Tools" section. As new tools are developed, product briefs and user guides may be obtained from the Microchip web site (www.microchip.com) or from your local Microchip Sales Office. Code development recommendations and techniques are provided in the "Code Development" section. Microchip offers other reference tools to speed the development cycle. These include: * * * * * * Application Notes Reference Designs Microchip web site Microchip BBS Local Sales Offices with Field Application Support Corporate Support Line Additional avenues of assistance can be found in many Web User Groups including the MIT reflector PIClist. The Microchip web site lists other sites that may be useful references. DS31001A-page 1-6 1997 Microchip Technology Inc. Section 1. Introduction 1.5 1 Device Varieties * * * * * Memory technology Operating voltage Operating temperature range Operating frequency Packaging Microchip has a large number of options and option combinations, one of which should fulfill your requirements. 1.5.1 Memory Varieties Memory technology has no effect on the logical operation of a device. Due to the different processing steps required, some electrical characteristics may vary between devices with the same feature set/pinout but with different memory technologies. An example is the electrical characteristic VIL (Input Low Voltage), which may have some difference between a typical EPROM device and a typical ROM device. Each device has a variety of frequency ranges and packaging options available. Depending on application and production requirements, the proper device options can be identified using the information in the Product Selection System section at the end of each data sheet. When placing orders, please use the "Product Identification System" at the back of the data sheet to specify the correct part number. When discussing the functionality of the device, the memory technology and the voltage range do not matter. Microchip offers three program memory types. The memory type is designated in the part number by the first letter(s) after the family affiliation designators. 1. 2. 3. 1.5.1.1 C, as in PIC16CXXX. These devices have EPROM type memory. CR, as in PIC16CRXXX. These devices have ROM type memory. F, as in PIC16FXXX. These devices have Flash type memory. EPROM Microchip focuses on Erasable Programmable Read Only Memory (EPROM) technology to give the customers flexibility throughout their entire design cycle. With this technology Microchip offers various packaging options as well as services. 1.5.1.2 Read Only Memory (ROM) Devices Microchip offers a masked Read Only Memory (ROM) version of several of the highest volume parts, thus giving customers a lower cost option for high volume, mature products. ROM devices do not allow serialization information in the program memory space. For information on submitting ROM code, please contact your local Microchip sales office. 1.5.1.3 Flash Memory Devices These devices are electrically erasable, and can therefore be offered in a low cost plastic package. Being electrically erasable, these devices can be both erased and reprogrammed without removal from the circuit. A device will have the same specifications whether it is used for prototype development, pilot programs, or production. 1997 Microchip Technology Inc. DS31001A-page 1-7 Introduction Once the functional requirements of the device are specified, some other decisions need to be made. These include: PICmicro MID-RANGE MCU FAMILY 1.5.2 Operating Voltage Range Options All Mid-Range PICmicroTM MCUs operate over the standard voltage range. Devices are also offered which operate over an extended voltage range (and reduced frequency range). Table 1-1 shows all possible memory types and voltage range designators for the PIC16CXXX MCU family. The designators are in bold typeface. Table 1-1: Device Memory Type and Voltage Range Designators Voltage Range Memory Type Standard EPROM ROM Flash Extended PIC16CXXX PIC16CRXXX PIC16FXXX PIC16LCXXX PIC16LCRXXX PIC16LFXXX Note:Not all memory types may be available for a particular device. As you can see in Table 1-2, Microchip specifications its extended range devices at a more conservative voltage range until device characterization has ensured they will be able to meet the goal of their final design specifications. Table 1-2: Typical Voltage Ranges for Each Device Type Typical Voltage Range (1) EPROM ROM Flash Standard Extended C 4.5 - 6.0V CR 4.5 - 6.0V F 4.5 - 6.0V Before device characterization LC 3.0 - 6.0V LCR 3.0 - 6.0V LF 3.0 - 6.0V Final specification (2) LC 2.5 - 6.0V LCR 2.5 - 6.0V LF 2.0 - 6.0V Note 1: Devices fabricated in Microchip's 120K Process Technology will have a maximum limit on VDD of 5.5V. New device data sheets will specify Microchip's technology designation 2: This voltage range depends on the results of device characterization. DS31001A-page 1-8 1997 Microchip Technology Inc. Section 1. Introduction 1.5.3 1 Packaging Varieties The first is a device with an erasure window. Typically these are found in packages with a ceramic body. These devices are used for the development phase, since the device's program memory can be erased and reprogrammed many times. The second package type is a low cost plastic package. This package type is used in production where device cost is to be kept to a minimum. Lastly, there is the DIE option. A DIE is an unpackaged device that has been tested. DIEs are used in low cost designs and designs where board space is at a minimum. Table 1-3 shows a quick summary of this. Table 1-3: Typical Package Uses Package Type Typical Usage Windowed Plastic DIE Development Mode Production Special Applications, such as those which require minimum board space 1997 Microchip Technology Inc. DS31001A-page 1-9 Introduction Depending on the development phase of your project, one of three package types would be used: PICmicro MID-RANGE MCU FAMILY 1.5.3.4 UV Erasable Devices The UV erasable version of EPROM program memory devices is optimal for prototype development and pilot programs. These devices can be erased and reprogrammed to any of the configuration modes. Third party programmers are also available; refer to Microchip's Third Party Guide (DS00104) for a list of sources. The amount of time required to completely erase a UV erasable device depends on: the wavelength of the light, its intensity, distance from UV source, the process technology of the device (how small are the memory cells). Note: 1.5.3.5 Fluorescent lights and sunlight both emit ultraviolet light at the erasure wavelength. Leaving a UV erasable device's window uncovered could cause, over time, the devices memory cells to become erased. The erasure time for a fluorescent light is about three years, while sunlight requires only about one week. To prevent the memory cells from losing data, an opaque label should be placed over the erasure window. One-Time-Programmable (OTP) Devices The availability of OTP devices is especially useful for customers expecting code changes and updates. OTP devices, packaged in plastic packages, permit the user to program them once. In addition to the program and data EPROM memories, the configuration bits must be programmed. 1.5.3.6 Flash Devices A Flash device allows its memory to be changed by an electric charge. This means that the system can be designed so that programming may be performed in-circuit. Since no window is required, the lower cost plastic packages can used for these devices. 1.5.3.7 EEPROM Devices An EEPROM device allows its memory to be erased by an electric charge. This means that the system can be designed so that erasure and reprogramming may be performed in-circuit. Since no window is required, the lower cost plastic packages can used for these devices. DS31001A-page 1-10 1997 Microchip Technology Inc. Section 1. Introduction 1.5.3.8 1 ROM Devices 1.5.3.9 DIE The DIE option allows the board size to become as small as physically possible. The DIE Support document (DS30258) explains general information about using and designing with DIE. There are also individual specification sheets that detail DIE specific information. Manufacturing with DIE requires special knowledge and equipment. This means that the number of manufacturing houses that support DIE will be limited. If you decide to use the DIE option, please research your manufacturing sites to ensure that they will be able to meet the specialized requirements of DIE use. 1.5.3.10 Specialized Services For OTP customers with established code, Microchip offers two specialized services. These two services, Quick Turn Production Programming and Serialized Quick Turn Production Programming, that allow customers to shorten their manufacturing cycle time. 1.5.3.11 Quick Turn Production (QTP) Programming Microchip offers this programming service for factory production orders. This service is made available for users who choose not to program a medium to high quantity of units and whose code patterns have stabilized. The devices are identical to the OTP devices but with all EPROM locations and configuration options already programmed by the factory. Certain code and prototype verification procedures apply before production shipments are available. Please contact your local Microchip sales office for more details. 1.5.3.12 Serialized Quick Turn Production (SQTPSM) Programming Microchip offers a this unique programming service where a few user-defined locations in each device are programmed with different serial numbers. The serial numbers may be random, pseudo-random or sequential. Serial programming allows each device to have a unique number which can serve as an entry-code, password or ID number. 1997 Microchip Technology Inc. DS31001A-page 1-11 Introduction ROM devices have their program memory fixed at the time of the silicon manufacture. Since the program memory cannot be changed, the device can be housed in the lower cost plastic package. PICmicro MID-RANGE MCU FAMILY 1.6 Style and Symbol Conventions Throughout this document, certain style and font format changes are used. Most format changes imply a distinction should be made for the emphasized text. The MCU industry has many symbols and non-conventional word definitions/abbreviations. Table 1-4 provides a description for many of the conventions contained in this document. A glossary is provided in the "Glossary" section, which contains more word and abbreviation definitions that are used throughout this manual. 1.6.1 Document Conventions Table 1-4 defines some of the symbols and terms used throughout this manual. Table 1-4: Document Conventions Symbol or Term Description set clear reset To force a bit/register to a value of logic `1'. To force a bit/register to a value of logic `0'. 1) To force a register/bit to its default state. 2) A condition in which the device places itself after a device reset occurs. Some bits will be forced to `0' (such as interrupt enable bits), while others will be forced to `1' (such as the I/O data direction bits). 0xnn or nnh Designates the number `nn' in the hexadecimal number system. These conventions are used in the code examples. B'bbbbbbbb' Designates the number `bbbbbbbb' in the binary number system. This convention is used in the text and in figures and tables. R-M-W Read - Modify - Write. This is when a register or port is read, then the value is modified, and that value is then written back to the register or port. This action can occur from a single instruction (such as bit set file, BSF) or a sequence of instructions. : (colon) Used to specify a range, or the concatenation of registers / bits / pins. An example is TMR1H:TMR1L is the concatenation of two 8-bit registers to form a 16-bit timer value, while SSPM3:SSPM0 are 4-bits used to specify the mode of the SSP module. Concatenation order (left-right) usually specifies a positional relationship (MSb to LSb, higher to lower). <> Specifies bit(s) locations in a particular register. An example is SSPCON (or SSPCON<3:0>) specifies the register and associated bits or bit positions. Courier Font Used for code examples, binary numbers, and for Instruction Mnemonics in the text. Times Font Used for equations and variables. Times, Bold Font, Used in explanatory text for items called out from a graphic/equaItalics tion/example. Note Notes present information that we wish to reemphasize, either to help you avoid a common pitfall, or make you aware of operating differences between some device family members. A Note is always in a shaded box (as below), unless used in a table, where it is at the bottom of the table (as in this table). Note: This is a note in a note box. Caution(1) A caution statement describes a situation that could potentially damage software or equipment. Warning(1) A warning statement describes a situation that could potentially cause personnel harm. Note 1: The information in a caution or a warning is provided for your protection. Please read each caution and warning carefully. DS31001A-page 1-12 1997 Microchip Technology Inc. Section 1. Introduction 1.6.2 1 Electrical Specifications The "Electrical Specifications" section shows all the specifications that are documented for all devices. No one device has all these specifications. This section is intended to let you know the types of parameters that Microchip specifies. The value of each specification is device dependent, though we strongly attempt to keep them consistent across all devices. Table 1-5: Electrical Specification Parameter Numbering Convention Parameter Number Format Comment Dxxx DC Specification Axxx DC Specification for Analog peripherals xxx Timing (AC) Specification PDxxx Device Programming DC Specification Pxxx Device Programming Timing (AC) Specification Legend: xxx: represents a number. 1997 Microchip Technology Inc. DS31001A-page 1-13 Introduction Throughout this manual there will be references to electrical specification parameter numbers. A parameter number represents a unique set of characteristics and conditions that is consistent between every data sheet, though the actual parameter value may vary from device to device. PICmicro MID-RANGE MCU FAMILY 1.7 Related Documents Microchip, as well as other sources, offers additional documentation which can aid in your development with PICmicro MCUs. These lists contain the most common documentation but other documents may also be available. Please check the Microchip web site (www.microchip.com) for the latest published technical documentation. 1.7.1 Microchip Documentation The following documents are available from Microchip. Many of these documents provide application specific information that give actual examples of using, programming and designing with PICmicro MCUs. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. DS31001A-page 1-14 MPASM User's Guide (DS33014) This document explains how to use Microchip's MPASM assembler. MPLABTM-C Compiler User's Guide (DS51014) This document explains how to use Microchip's MPLAB-C C compiler. MPLAB User's Guide (DS51025) This document explains how to use Microchip's MPLAB Integrated Development Environment. MPLAB Editor User's Guide (DS30420) This document explains how to use Microchip's MPLAB built-in editor. PICMASTER(R) User's Guide (DS30421) This document explains how to use Microchip's PICMASTER In-Circuit Emulator. MPSIM User's Guide (DS30027) This document explains how to use Microchip's MPLAB Simulator. PRO MATE(R) User's Guide (DS30082) This document explains how to use Microchip's PRO MATE universal programmer. PICSTART(R)-Plus User's Guide (DS51028) This document explains how to use Microchip's PICSTART-Plus low-cost universal programmer. fuzzyTECH(R)-MP User's Guide (DS30389) This document explains how to use the fuzzyTECH-MP fuzzy logic code generator. MP-DriveWayTM User's Guide (DS51027) This document explains how to use the MP-DriveWay code generator. fuzzyTECH-MP Fuzzy Logic Handbook (DS30238) This document explains the basics of fuzzyTECH-MP fuzzy. Embedded Control Handbook Volume I (DS00092) This document contains a plethora of application notes. This is useful for insight on how to use the device (or parts of it) as well as getting started on your particular application due to the availability of extensive code files. Embedded Control Handbook Volume II (DS00167) This document contains the Math Libraries for PICmicro MCUs. In-Circuit Serial Programming GuideTM (DS30277) This document discusses implementing In-Circuit Serial Programming. PICDEM-1 User's Guide (DS351079) This document explains how to use Microchip's PICDEM-1 demo board. PICDEM-2 User's Guide (DS30374) This document explains how to use Microchip's PICDEM-2 demo board. PICDEM-3 User's Guide (DS33015) This document explains how to use Microchip's PICDEM-3 demo board. Third Party Guide (DS00104) This document lists Microchip's third parties, as well as various consultants. DIE Support (DS30258) This document gives information on using Microchip products in DIE form. 1997 Microchip Technology Inc. Section 1. Introduction 1.7.2 1 Third Party Documentation DOCUMENT LANGUAGE The PIC16C5X Microcontroller: A Practical Approach to Embedded Control Bill Rigby/ Terry Dalby, Tecksystems Inc. 0-9654740-0-3............................................................................................................ English Easy PIC'n David Benson, Square 1 Electronics 0-9654162-0-8............................................................................................................ English A Beginners Guide to the Microchip PIC(R) Nigel Gardner, Bluebird Electronics 1-899013-01-6............................................................................................................ English PIC Microcontroller Operation and Applications DN de Beer, Cape Technikon ..................................................................................... English Digital Systems and Programmable Interface Controllers WP Verburg, Pretoria Technikon ................................................................................ English Mikroprozessor PIC16C5X Michael Rose, Huthig 3-7785-2169-1...........................................................................................................German Mikroprozessor PIC17C42 Michael Rose, Huthig 3-7785-2170-5...........................................................................................................German Les Microcontrolleurs PIC et mise en oeuvre Christian Tavernier, Dunod 2-10-002647-X ............................................................................................................French Micontrolleurs PIC a structure RISC C.F. Urbain, Publitronic 2-86661-058-X ............................................................................................................French New Possibilities with the Microchip PIC RIGA ......................................................................................................................... Russian 1997 Microchip Technology Inc. DS31001A-page 1-15 Introduction There are several documents available from third party sources around the world. Microchip does not review these documents for technical accuracy, however they may be a helpful source for understanding the operation of Microchip MCU devices. This is not necessarily a complete list, but are the documents that we were aware of at the time of printing. For more information on how to contact some of these sources, as well as any new sources that we become aware of, please visit the Microchip web site. PICmicro MID-RANGE MCU FAMILY DOCUMENT LANGUAGE PIC16C5X/71/84 Development and Design, Part 1 United Tech Electronic Co. Ltd 957-21-0807-7.......................................................................................................... Chinese PIC16C5X/71/84 Development and Design, Part 2 United Tech Electronic Co. Ltd 957-21-1152-3.......................................................................................................... Chinese PIC16C5X/71/84 Development and Design, Part 3 United Tech Electronic Co. Ltd 957-21-1187-6.......................................................................................................... Chinese PIC16C5X/71/84 Development and Design, Part 4 United Tech Electronic Co. Ltd 957-21-1251-1.......................................................................................................... Chinese PIC16C5X/71/84 Development and Design, Part 5 United Tech Electronic Co. Ltd 957-21-1257-0.......................................................................................................... Chinese PIC16C84 MCU Architecture and Software Development ICC Company 957-8716-79-6.......................................................................................................... Chinese DS31001A-page 1-16 1997 Microchip Technology Inc. Section 1. Introduction 1.8 1 Related Application Notes Title Application Note # A Comparison of Low End 8-bit Microcontrollers AN520 PIC16C54A EMI Results AN577 Continuous Improvement AN503 Improving the Susceptibility of an Application to ESD AN595 Plastic Packaging and the Effects of Surface Mount Soldering Techniques AN598 1997 Microchip Technology Inc. DS31001A-page 1-17 Introduction This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the PIC16CXXX Mid-Range MCU family (that is they may be written for the Base-Line, or the High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to an introduction to Microchip's PICmicro MCUs are: PICmicro MID-RANGE MCU FAMILY 1.9 Revision History Revision A This is the initial released revision of Microchip's PICmicro MCUs Introduction. DS31001A-page 1-18 1997 Microchip Technology Inc. M Section 2. Oscillator HIGHLIGHTS This section of the manual contains the following major topics: Introduction ....................................................................................................................2-2 Oscillator Configurations ................................................................................................2-2 Crystal Oscillators / Ceramic Resonators ......................................................................2-4 External RC Oscillator..................................................................................................2-12 Internal 4 MHz RC Oscillator .......................................................................................2-13 Effects of Sleep Mode on the On-chip Oscillator .........................................................2-17 Effects of Device Reset on the On-chip Oscillator .......................................................2-17 Design Tips ..................................................................................................................2-18 Related Application Notes............................................................................................2-19 Revision History ...........................................................................................................2-20 1997 Microchip Technology Inc. DS31002A page 2-1 Oscillator 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2 PICmicro MID-RANGE MCU FAMILY 2.1 Introduction The internal oscillator circuit is used to generate the device clock. The device clock is required for the device to execute instructions and for the peripherals to function. Four device clock periods generate one internal instruction clock (TCY) cycle. There are up to eight different modes which the oscillator may have. There are two modes which allow the selection of the internal RC oscillator clock out (CLKOUT) to be driven on an I/O pin, or allow that I/O pin to be used for a general purpose function. The oscillator mode is selected by the device configuration bits. The device configuration bits are nonvolatile memory locations and the operating mode is determined by the value written during device programming. The oscillator modes are: * * * * * * * * LP XT HS RC EXTRC EXTRC INTRC INTRC Low Frequency (Power) Crystal Crystal/Resonator High Speed Crystal/Resonator External Resistor/Capacitor (same as EXTRC with CLKOUT) External Resistor/Capacitor External Resistor/Capacitor with CLKOUT Internal 4 MHz Resistor/Capacitor Internal 4 MHz Resistor/Capacitor with CLKOUT These oscillator options are made available to allow a single device type the flexibility to fit applications with different oscillator requirements. The RC oscillator option saves system cost while the LP crystal option saves power. Configuration bits are used to select the various options. For more details on the device configuration bits, see the "Device Characteristics" section. 2.2 Oscillator Configurations 2.2.1 Oscillator Types Mid-Range devices can have up to eight different oscillator modes. The user can program up to three device configuration bits (FOSC2, FOSC1 and FOSC0) to select one of these eight modes: * * * * * * * * LP XT HS RC EXTRC EXTRC INTRC INTRC Low Frequency (Power) Crystal Crystal/Resonator High Speed Crystal/Resonator External Resistor/Capacitor (same as EXTRC with CLKOUT) External Resistor/Capacitor External Resistor/Capacitor with CLKOUT Internal 4 MHz Resistor/Capacitor Internal 4 MHz Resistor/Capacitor with CLKOUT The main difference between the LP, XT, and HS modes is the gain of the internal inverter of the oscillator circuit which allows the different frequency ranges. Table 2-1 and Table 2-2 give information to aid in selecting an oscillator mode. In general, use the oscillator option with the lowest possible gain which still meet specifications. This will result in lower dynamic currents (IDD). The frequency range of each oscillator mode is the recommended (tested) frequency cutoffs, but the selection of a different gain mode is acceptable as long as a thorough validation is performed (voltage, temperature, component variations (Resistor, Capacitor, and internal microcontroller oscillator circuitry)). The RC mode and the EXTRC with CLKOUT mode have the same functionality. They are named like this to help describe their operation vs. the other oscillator modes. DS31002A-page 2-2 1997 Microchip Technology Inc. Section 2. Oscillator Table 2-1: Selecting the Oscillator Mode for Devices with FOSC1:FOSC0 Configuration bits OSC FOSC1:FOSC0 Mode RC 1 0 HS 0 1 XT 0 0 LP Table 2-2: 1 1 0 1 0 1 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 1997 Microchip Technology Inc. -- Least expensive solution for device oscillation (only an external resistor and capacitor is required). Most variation in time-base. Device's default mode. High Gain High frequency application. Oscillator circuit's mode consumes the most current of the three crystal modes. Medium Gain Standard crystal/resonator frequency. Oscillator circuit's mode consumes the middle current of the three crystal modes. Low Gain Low power/frequency applications. Oscillator circuit's mode consumes the least current of the three crystal modes. Selecting the Oscillator Mode for Devices with FOSC2:FOSC0 Configuration bits FOSC2:FOSC0 1 1 1 Comment OSC Mode EXTRC with CLKOUT EXTRC OSC Feedback Inverter Gain Comment -- Inexpensive solution for device oscillation. Most variation in timebase. CLKOUT is enabled on pin. Device's default mode. -- Inexpensive solution for device oscillation. Most variation in timebase. CLKOUT is disabled (use as I/O) on pin. INTRC -- Least expensive solution for device oscillation. with 4 MHz oscillator, which can be tuned. CLKOUT CLKOUT is enabled on pin. INTRC -- Least expensive solution for device oscillation. 4 MHz oscillator, which can be tuned. CLKOUT is disabled (use as I/O) on pin. -- -- Reserved HS High Gain High frequency application. Oscillator circuit's mode consumes the most current of the three crystal modes. XT Medium Gain Standard crystal/resonator frequency. Oscillator circuit's mode consumes the middle current of the three crystal modes. LP Low Gain Low power/frequency applications. Oscillator circuit's mode consumes the least current of the three crystal modes. DS31002A-page 2-3 2 Oscillator 1 1 OSC Feedback Inverter Gain PICmicro MID-RANGE MCU FAMILY 2.3 Crystal Oscillators / Ceramic Resonators In XT, LP or HS modes a crystal or ceramic resonator is connected to the OSC1 and OSC2 pins to establish oscillation (Figure 2-1). The PICmicro oscillator design requires the use of a parallel cut crystal. Using a series cut crystal may give a frequency out of the crystal manufacturer's specifications. When in XT, LP or HS modes, the device can have an external clock source drive the OSC1 pin (Figure 2-3). Figure 2-1: Crystal or Ceramic Resonator Operation (HS, XT or LP Oscillator Mode) OSC1 C1 To internal logic XTAL RF (2) (3) SLEEP OSC2 Rs (1) C2 To internal logic (3) PIC16CXXX Note 1: A series resistor, RS, may be required for AT strip cut crystals. 2: The feedback resistor, RF, is typically in the range of 2 to 10 M. 3: Depending on the device, the buffer to the internal logic may be either before or after the oscillator inverter. DS31002A-page 2-4 1997 Microchip Technology Inc. Section 2. Oscillator 2.3.1 Oscillator / Resonator Start-up As the device voltage increases from VSS, the oscillator will start its oscillations. The time required for the oscillator to start oscillating depends on many factors. These include: * * * * * * * * * Crystal / resonator frequency Capacitor values used (C1 and C2 in Figure 2-1) Device VDD rise time System temperature Series resistor value (and type) if used (Rs in Figure 2-1) Oscillator mode selection of device (which selects the gain of the internal oscillator inverter) Crystal quality Oscillator circuit layout System noise Figure 2-2: Example Oscillator / Resonator Start-up Characteristics Maximum VDD of System Device VDD Voltage 0V Crystal Start-up Time 1997 Microchip Technology Inc. Time DS31002A-page 2-5 2 Oscillator Figure 2-2 graphs an example oscillator / resonator start-up. The peak-to-peak voltage of the oscillator waveform can be quite low (less than 50% of device VDD) where the waveform is centered at VDD/2 (refer to parameters D033 and D043 in the "Electrical Specifications" section). PICmicro MID-RANGE MCU FAMILY 2.3.2 Component Selection Figure 2-1 is a diagram of the devices crystal or ceramic resonator circuitry. The resistance for the feedback resistor, RF, is typically within the 2 to 10 M range. This varies with device voltage, temperature, and process variations. A series resistor, Rs, may be required if an AT strip cut crystal is used. Be sure to include the device's operating voltage and the device's manufacturing process when determining resistor requirements. As you can see in Figure 2-1, the connection to the device's internal logic is device dependent. See the applicable data sheet for device specifics. The typical values of capacitors (C1, C2) are given in Table 2-3 and Table 2-4. Each device's data sheet will give the specific values that Microchip tested. Table 2-3: Typical Capacitor Selection for Ceramic Resonators Ranges tested: Mode Frequency C1 / C2(1) XT 455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz 20.0 MHz 22 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF TBD HS Resonators used: 455 kHz Panasonic EFO-A455K04B 0.3% 2.0 MHz Murata Erie CSA2.00MG 0.5% 4.0 MHz Murata Erie CSA4.00MG 0.5% 8.0 MHz Murata Erie CSA8.00MT 0.5% 16.0 MHz Murata Erie CSA16.00MX 0.5% 20.0 MHz TBD TBD Note 1: Recommended values of C1 and C2 are identical to the ranges tested above. Higher capacitance increases the stability of the oscillator but also increases the start-up time. These values are for design guidance only. Since each resonator has its own characteristics, the user should consult the resonator manufacturer for appropriate values of external component or verify oscillator performance. 2: All resonators tested required external capacitors. DS31002A-page 2-6 1997 Microchip Technology Inc. Section 2. Oscillator Table 2-4: Typical Capacitor Selection for Crystal Oscillator Mode Freq C1(1) C2(1) LP 32 kHz 200 kHz 100 kHz 2 MHz 4 MHz 8 MHz 10 MHz 20 MHz 68 - 100 pF 15 - 30 pF 68 - 150 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF 68 - 100 pF 15 - 30 pF 150 - 200 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF 15 - 30 pF XT HS 2 Crystals used: 1997 Microchip Technology Inc. DS31002A-page 2-7 Oscillator 32.768 kHz Epson C-001R32.768K-A 20 PPM 100 kHz Epson C-2 100.00 KC-P 20 PPM 200 kHz STD XTL 200.000 kHz 20 PPM 2.0 MHz ECS ECS-20-S-2 50 PPM 4.0 MHz ECS ECS-40-S-4 50 PPM 10.0 MHz ECS ECS-100-S-4 50 PPM 20.0 MHz ECS ECS-200-S-4 50 PPM Note 1: Higher capacitance increases the stability of the oscillator but also increases the start-up time. These values are for design guidance only. A series resistor, Rs, may be required in HS mode as well as XT mode to avoid overdriving crystals with low drive level specification. Since each crystal has its own characteristics, the user should consult the crystal manufacturer for appropriate values of external components or verify oscillator performance. PICmicro MID-RANGE MCU FAMILY 2.3.3 Tuning the Oscillator Circuit Since Microchip devices have wide operating ranges (frequency, voltage, and temperature; depending on the part and version ordered) and external components (crystals, capacitors,...), of varying quality and manufacture; validation of operation needs to be performed to ensure that the component selection will comply with the requirements of the application. There are many factors that go into the selection and arrangement of these external components. These factors include: * * * * * * * * * * * * DS31002A-page 2-8 amplifier gain desired frequency resonant frequency(s) of the crystal temperature of operation supply voltage range start-up time stability crystal life power consumption simplification of the circuit use of standard components combination which results in fewest components 1997 Microchip Technology Inc. Section 2. Oscillator 2.3.3.1 Determining Best Values for Crystals, Clock Mode, C1, C2, and Rs The best method for selecting components is to apply a little knowledge and a lot of trial, measurement, and testing. Crystals are usually selected by their parallel resonant frequency only, however other parameters may be important to your design, such as temperature or frequency tolerance. Application Note AN588 is an excellent reference if you would like to know more about crystal operation and their ordering information. The PICmicrosTM internal oscillator circuit is a parallel oscillator circuit, which requires that a parallel resonant crystal be selected. The load capacitance is usually specified in the 20 pF to 32 pF range. The crystal will oscillate closest to the desired frequency with capacitance in this range. It may be necessary to sometimes juggle these values a bit, as described later, in order to achieve other benefits. C1 and C2 should also be initially selected based on the load capacitance as suggested by the crystal manufacturer and the tables supplied in the device data sheet. The values given in the Microchip data sheet can only be used as a starting point, since the crystal manufacturer, supply voltage, and other factors already mentioned may cause your circuit to differ from the one used in the factory characterization process. Ideally, the capacitance is chosen (within the range of the recommended crystal load preferably) so that it will oscillate at the highest temperature and lowest VDD that the circuit will be expected to perform under. High temperature and low VDD both have a limiting affect on the loop gain, such that if the circuit functions at these extremes, the designer can be more assured of proper operation at other temperatures and supply voltage combinations. The output sine wave should not be clipped in the highest gain environment (highest VDD and lowest temperature) and the sine output amplitude should be great enough in the lowest gain environment (lowest VDD and highest temperature) to cover the logic input requirements of the clock as listed in the device data sheet. A method for improving start-up is to use a value of C2 greater than C1. This causes a greater phase shift across the crystal at power-up, which speeds oscillator start-up. Besides loading the crystal for proper frequency response, these capacitors can have the effect of lowering loop gain if their value is increased. C2 can be selected to affect the overall gain of the circuit. A higher C2 can lower the gain if the crystal is being over driven (see also discussion on Rs). Capacitance values that are too high can store and dump too much current through the crystal, so C1 and C2 should not become excessively large. Unfortunately, measuring the wattage through a crystal is tricky business, but if you do not stray too far from the suggested values you should not have to be concerned with this. A series resistor, Rs, is added to the circuit if, after all other external components are selected to satisfaction, the crystal is still being over driven. This can be determined by looking at the OSC2 pin, which is the driven pin, with an oscilloscope. Connecting the probe to the OSC1 pin will load the pin too much and negatively affect performance. Remember that a scope probe adds its own capacitance to the circuit, so this may have to be accounted for in your design, i.e. if the circuit worked best with a C2 of 20 pF and scope probe was 10 pF, a 30 pF capacitor may actually be called for. The output signal should not be clipping or squashed. Overdriving the crystal can also lead to the circuit jumping to a higher harmonic level or even crystal damage. 1997 Microchip Technology Inc. DS31002A-page 2-9 Oscillator Clock mode is primarily chosen by using the FOSC parameter specification (parameter 1A) in the device's data sheet, based on frequency. Clock modes (except RC) are simply gain selections, lower gain for lower frequencies, higher gain for higher frequencies. It is possible to select a higher or lower gain, if desired, based on the specific needs of the oscillator circuit. 2 PICmicro MID-RANGE MCU FAMILY The OSC2 signal should be a nice clean sine wave that easily spans the input minimum and maximum of the clock input pin (4V to 5V peak to peak for a 5V VDD is usually good). An easy way to set this is to again test the circuit at the minimum temperature and maximum VDD that the design will be expected to perform in, then look at the output. This should be the maximum amplitude of the clock output. If there is clipping or the sine wave is squashing near VDD and VSS at the top and bottom, and increasing load capacitors will risk too much current through the crystal or push the value too far from the manufacturer's load specification, then add a trimpot between the output pin and C2, and adjust it until the sine wave is clean. Keeping it fairly close to maximum amplitude at the low temperature and high VDD combination will assure this is the maximum amplitude the crystal will see and prevent overdriving. A series resistor, Rs, of the closest standard value, can now be inserted in place of the trimpot. If Rs is too high, perhaps more than 20k ohms, the input will be too isolated from the output, making the clock more susceptible to noise. If you find a value this high is needed to prevent overdriving the crystal, try increasing C2 to compensate. Try to get a combination where Rs is around 10k or less, and load capacitance is not too far from the 20 pF or 32 pF manufacturer specification. 2.3.3.1.1 Start-up The most difficult time for the oscillator to start-up is when waking up from sleep. This is because the load capacitors have both partially charged to some quiescent value, and phase differential at wake-up is minimal. Thus, more time is required to achieve stable oscillation. Remember also that low voltage, high temperatures, and the lower frequency clock modes also impose limitations on loop gain, which in turn affects start-up. Each of the following factors makes thing worse: * * * * * * a low frequency design (with its low gain clock mode) a quiet environment (such as a battery operated device) operating outside the noisy RF area (such as in a shielded box) low voltage high temperature waking up from sleep. Noise actually helps a design for oscillator start-up, since it helps kick start the oscillator. 2.3.4 External Clock Input If the PICmicro's internal oscillator is not being used, and the device will be driven from an external clock, be sure to set the oscillator mode to one of the crystal modes (LP, XT, or HS). That is, something other than one of the RC modes, since RC mode will fight with the injected input. Ideally you would select the mode that corresponds to the frequency injected, but this is of less importance here since the clock is only driving its internal logic, and not a crystal loop circuit. It may be possible to select a clock mode lower than would be needed by an oscillator circuit, and thereby save some of the power that would be used exercising the inverting amplifier. Make sure the OSC2 signal amplitude covers the needed logic thresholds of the device. Figure 2-3: External Device Clock Input Operation (HS, XT or LP Oscillator Modes) clock from external system OSC1 PIC16CXXX (1) Open OSC2 Note 1: A resistor to ground may be used to reduce system noise. This may increase system current. DS31002A-page 2-10 1997 Microchip Technology Inc. Section 2. Oscillator 2.3.5 External Crystal Oscillator Circuit for Device Clock Sometimes more than one device needs to be clocked from a single crystal. Since Microchip does not recommend connecting other logic to the PICmicro's internal oscillator circuit, an external crystal oscillator circuit is recommended. Each device will then have an external clock source, and the number of devices that can be driven will depend on the buffer drive capability. This circuit is also useful when more than one device (PICmicro) needs to operate synchronously to each other. Either a prepackaged oscillator can be used or a simple oscillator circuit with TTL gates can be built. Prepackaged oscillators provide a wide operating range and better stability. A well-designed crystal oscillator will provide good performance with TTL gates. Two types of crystal oscillator circuits can be used; one with series resonance, or one with parallel resonance. Figure 2-4: External Parallel Resonant Crystal Oscillator Circuit +5V To Other Devices 10k 4.7 k 74AS04 PIC16CXXX CLKIN 74AS04 10 k XTAL 10 k 20 pF 20 pF Figure 2-5 shows an external series resonant oscillator circuit. This circuit is also designed to use the fundamental frequency of the crystal. The inverter performs a 180-degree phase shift in a series resonant oscillator circuit. The 330 k resistors provide the negative feedback to bias the inverters in their linear region. Figure 2-5: External Series Resonant Crystal Oscillator Circuit 330 k 330 k 74AS04 74AS04 To Other Devices 74AS04 PIC16CXXX CLKIN 0.1 F XTAL When the device is clocked from an external clock source (as in Figure 2-4 or Figure 2-5) then the microcontroller's oscillator must be configured for LP, XT or HS mode (Figure 2-3). 1997 Microchip Technology Inc. DS31002A-page 2-11 2 Oscillator Figure 2-4 shows implementation of an external parallel resonant oscillator circuit. The circuit is designed to use the fundamental frequency of the crystal. The 74AS04 inverter performs the 180-degree phase shift that a parallel oscillator requires. The 4.7 k resistor provides the negative feedback for stability. The 10 k potentiometer biases the 74AS04 in the linear region. PICmicro MID-RANGE MCU FAMILY 2.4 External RC Oscillator For timing insensitive applications the "EXTRC" device option offers additional cost savings. The RC oscillator frequency is a function of; the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external REXT and CEXT components used. Figure 2-6 shows how the RC combination is connected to a PIC16CXXX. For REXT values below 2.2 k, oscillator operation may become unstable, or stop completely. For very high REXT values (e.g. 1 M), the oscillator becomes sensitive to noise, humidity and leakage. Thus, we recommend keeping REXT between 3 k and 100 k. Figure 2-6: EXTRC Oscillator Mode V DD REXT OSC1 Fosc CEXT Internal clock PIC16CXXX VSS Fosc/4 (1) OSC2/CLKOUT Note 1: This output may also be able to be configured as a general purpose I/O pin. Although the oscillator will operate with no external capacitor (CEXT = 0 pF), we recommend using values above 20 pF for noise and stability reasons. With no or small external capacitance, the oscillation frequency can vary dramatically due to changes in external capacitances, such as PCB trace capacitance and package lead frame capacitance. See characterization data for RC frequency variation from part to part due to normal process variation. The variation is larger for larger resistance (since leakage current variation will affect RC frequency more for large R) and for smaller capacitance (since variation of input capacitance will affect RC frequency more). See characterization data for variation of oscillator frequency due to VDD for given REXT/CEXT values as well as frequency variation due to operating temperature for given REXT, CEXT, and VDD values. The oscillator frequency, divided by 4, is available on the OSC2/CLKOUT pin, and can be used for test purposes or to synchronize other logic (see Figure 4-3: "Clock/Instruction Cycle" in the "Architecture" section, for waveform). 2.4.1 RC Start-up As the device voltage increases, the RC will start its oscillations immediately after the pin voltage levels meet the input threshold specifications (parameters D032 and D042 in the "Electrical Specifications" section). The time required for the RC to start oscillating depends on many factors. These include: * * * * DS31002A-page 2-12 Resistor value used Capacitor value used Device VDD rise time System temperature 1997 Microchip Technology Inc. Section 2. Oscillator 2.5 Internal 4 MHz RC Oscillator The internal RC oscillator (not on all devices) provides a fixed 4 MHz (nominal) system clock at VDD = 5V and 25C, see the device data sheet's "Electrical Specifications" section for information on variation over voltage and temperature. The value in the OSCCAL register is used to tune the frequency of the internal RC oscillator. The calibration value that Microchip programs into the device will "trim" the internal oscillator to remove process variation from the oscillator frequency. The CAL3:CAL0 bits are used for fine calibration within a frequency window. Higher values of CAL3:CAL0 (from 0000 to 1111) yields higher clock speeds. When a 4 MHz internal RC oscillator frequency cannot be achieved by a CAL3:CAL0 value, the RC oscillator frequency can be increased or decreased by an offset frequency. The CALFST and CALSLW bits are used to enable a positive or negative frequency offset to place the internal RC frequency within the CAL3:CAL0 trim window. Upon a device reset, the OSCCAL register is forced to the midpoint value (CAL3:CAL0 = 7h, CALFST and CALSLW providing no offset). Register 2-1: OSCCAL Register R/W-0 CAL3 bit 7 bit 7:4 R/W-1 CAL2 R/W-1 CAL1 R/W-1 CAL0 R/W-0 CALFST R/W-0 CALSLW U-0 -- U-0 -- bit 0 CAL3:CAL0: Internal RC Oscillator Calibration bits 0000 = Lowest clock frequency within the trim range * * * 1111 = Highest clock frequency within the trim range bit 3 CALFST: Oscillator Range Offset bit 1 = Increases the frequency of the internal RC oscillator into the CAL3:CAL0 trim window 0 = No offset provided bit 2 CALSLW: Oscillator Range Offset bit 1 = Decreases the frequency of the internal RC oscillator into the CAL3:CAL0 trim window 0 = No offset provided Note: bit 1:0 When both bits are set, the CALFST bit overrides the CALSLW bit. Unimplemented: Read as '0' Note: These bits should be written as `0' when modifying the OSCCAL register, for compatibility with future devices. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Note: 1997 Microchip Technology Inc. - n = Value at POR reset OSCCAL is used to remove process variation from the internal RC oscillator of the device. The OSCCAL value should not be modified from the Microchip supplied value, and all timing critical functions should be adjusted by the application software. DS31002A-page 2-13 Oscillator Setting the CALFST bit offsets the internal RC for a higher frequency, while setting the CALSLW bit offsets the internal RC for a lower frequency. 2 PICmicro MID-RANGE MCU FAMILY Figure 2-7 shows the possible device frequencies from the uncalibrated point (at VDD = 5V, 25C, and OSCCAL = 70h), and the changes achievable by the OSCCAL register. Figure 2-7: Ideal Internal RC Oscillator Frequency vs. OSCCAL Register Value CAL3:CAL0 Trim Window Frequency 4 MHz See X-axis CAL3:CAL0 = 07h CALFST = 0 CALSLW = 0 CAL3:CAL0 = 0h CALFST = 0 CALSLW = 1 CAL3:CAL0 = 0h CALFST = 0 CALSLW = 0 CAL3:CAL0 = Fh CALFST = 0 CALSLW = 0 (slowest frequency) CAL3:CAL0 = Fh CALFST = 1 CALSLW = x (fastest frequency) Figure 2-8 shows an example of a device where by selecting one of the CAL3:CAL0 values, the frequency can corrected to 4 MHz. These bits can be considered the fine trimming of the frequency. Sometimes the device frequency at the uncalibrated point cannot be corrected to 4 MHz by the fine trimming of the CAL3:CAL0 bits value. Therefore two additional bits are available which give a large frequency offset (positive and negative) to move the frequency within the range where the fine trimming can work. These bits are the CALSLW and CALFST bits, which offset the internal RC frequency. The action of these bits are shown in Figure 2-9, and Figure 2-10. Figure 2-8: CAL3:CAL0 Trimming of Internal RC Oscillator Frequency Offset CAL3:CAL0 Trim Window Frequency > 4 MHz Internal RC Frequency at device reset CALFST = 0 CALFLW = 0 CAL3:CAL0 = 7h 4 MHz 1.5% (@ 5V, 25C) < 4 MHz CAL3:CAL0 = 0000 CAL3:CAL0 = 1111 One of the 16 possible calibration points DS31002A-page 2-14 1997 Microchip Technology Inc. Section 2. Oscillator Figure 2-9: CALFST Positive Internal RC Oscillator Frequency Offset CAL3:CAL0 Trim Window Internal RC Frequency with CALFST = 1 CALSLW = x Frequency 4 MHz 1.5% (@ 5V, 25C) Internal RC Frequency at device reset CALFST = 0 CALFLW = 0 et offs T LFS CA 2 < 4 MHz CAL3:CAL0 = 1111 One of the 16 possible CAL3:CAL0 calibration points Figure 2-10: CALSLW Negative Internal RC Oscillator Frequency Offset CAL3:CAL0 Trim Window Frequency > 4 MHz SLW L CA o t ffse Internal RC Frequency at device reset CALSLW = 0 CALFST = 0 Internal RC Frequency with CALSLW = 1 CALFST = 0 4 MHz 1.5% (@ 5V, 25C) CAL3:CAL0 = 0000 CAL3:CAL0 = 1111 One of the 16 possible CAL3:CAL0 calibration points 1997 Microchip Technology Inc. DS31002A-page 2-15 Oscillator CAL3:CAL0 = 0000 PICmicro MID-RANGE MCU FAMILY A calibration instruction is programmed into the last address of the implemented program memory. This instruction contains the calibration value for the internal RC oscillator. This value is programmed as a RETLW XX instruction where XX is the calibration value. In order to retrieve the calibration value, issue a CALL YY instruction where YY is the last location in the device's user accessible program memory. The calibration value is now loaded in the W register. The program should then perform a MOVWF OSCCAL instruction to load the value into the internal RC oscillator calibration register. Table 2-5 shows the location of the calibration value depending on the size of the program memory. Table 2-5: Calibration Value Location Program Memory Size (Words) 512 1K 2K 4K 8K Calibration Value Location 1FFh 3FFh 7FFh FFFh 1FFFh Note 1: Erasing the device (windowed devices) will also erase the factory programmed calibration value for the internal oscillator. Prior to erasing a windowed device, the internal oscillator calibration value must be saved. It is a good idea to write this value on the package of the device to ensure that the calibration value is not accidently lost. This saved valued must be restored into program memory calibration location before programming the device. Note 2: OSCCAL<1:0> are unimplemented and should be written as `0'. This will help ensure compatibility with future devices. 2.5.1 Clock Out The internal RC oscillator can be configured to provide a clock out signal on the CLKOUT pin when the configuration word address (2007h) is programmed with FOSC2, FOSC1, FOSC0 equal to `101' for Internal RC or `111' for External RC. CLKOUT, which is divided by 4, can be used for test purposes or to synchronize other logic. When the calibration value of the internal RC oscillator is accidently erased, the clock out feature allows the user to determine what the calibration value should be. This is achieved by writing a program which modifies (increments/decrements) the value of the OSCCAL register. When the CLKOUT pin is at 4 MHz ( 1.5%) at 5V and 25C, the OSCCAL register has the correct calibration value. This value then needs to be written to a port or shifted out serially, so that the value can be written down and programmed into the calibration location. DS31002A-page 2-16 1997 Microchip Technology Inc. Section 2. Oscillator 2.6 Effects of Sleep Mode on the On-chip Oscillator When the device executes a SLEEP instruction, the on-chip clocks and oscillator are turned off and the device is held at the beginning of an instruction cycle (Q1 state). With the oscillator off, the OSC1 and OSC2 signals will stop oscillating. Since all the transistor switching currents have been removed, sleep mode achieves the lowest current consumption of the device (only leakage currents). Enabling any on-chip feature that will operate during sleep will increase the current consumed during sleep. The user can wake from SLEEP through external reset, Watchdog Timer Reset or through an interrupt. Table 2-6: OSC1 and OSC2 Pin States in Sleep Mode OSC Mode OSC1 Pin OSC2 Pin EXTRC 2.7 Effects of Device Reset on the On-chip Oscillator Device resets have no effect on the on-chip crystal oscillator circuitry. The oscillator will continue to operate as it does under normal execution. While in reset, the device logic is held at the Q1 state so that when the device exits reset, it is at the beginning of an instruction cycle. The OSC2 pin, when used as the external clockout (EXTRC mode), will be held low during reset, and as soon as the MCLR pin is at VIH (input high voltage), the RC will start to oscillate. See Table 3-1, in the "Reset" section, for time-outs due to Sleep and MCLR reset. 2.7.1 Power-up Delays There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer, OST, intended to keep the chip in RESET until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only (POR and BOR). The PWRT is designed to keep the part in RESET while the power supply stabilizes. With these two timers on-chip, most applications need no external reset circuitry. For additional information on reset operation, see the "Reset" section. 1997 Microchip Technology Inc. DS31002A-page 2-17 2 Oscillator Floating, external resistor should At logic low pull high INTRC N.A. N.A. LP, XT, and HS Feedback inverter disabled, at Feedback inverter disabled, at quiescent voltage level quiescent voltage level See Table 3-1, in the "Reset" section, for time-outs due to Sleep and MCLR reset. PICmicro MID-RANGE MCU FAMILY 2.8 Design Tips Question 1: When looking at the OSC2 pin after power-up with an oscilloscope, there is no clock. What can cause this? Answer 1: 1. 2. 3. 4. Executing a SLEEP instruction with no source for wake-up (such as, WDT, MCLR, or an Interrupt). Verify that the code does not put device to sleep without providing for wake-up. If it is possible, try waking it up with a low pulse on MCLR. Powering up with MCLR held low will also give the crystal oscillator more time to start-up, but the Program Counter will not advance until the MCLR pin is high. The wrong clock mode is selected for the desired frequency. For a blank device, the default oscillator is EXTRC. Most parts come with the clock selected in the default RC mode, which will not start oscillation with a crystal or resonator. Verify that the clock mode has been programmed correctly. The proper power-up sequence has not been followed. If a CMOS part is powered through an I/O pin prior to power-up, bad things can happen (latch up, improper start-up etc.) It is also possible for brown-out conditions, noisy power lines at start-up, and slow VDD rise times to cause problems. Try powering up the device with nothing connected to the I/O, and power-up with a known, good, fast-rise, power supply. It is not as much of a problem as it may sound, but the possibility exists. Refer to the power-up information in the device data sheet for considerations on brown-out and power-up sequences. The C1 and C2 capacitors attached to the crystal have not been connected properly or are not the correct values. Make sure all connections are correct. The device data sheet values for these components will almost always get the oscillator running, they just might not be the optimal values for your design. Question 2: The PICmicro starts, but runs at a frequency much higher than the resonant frequency of the crystal. Answer 2: The gain is too high for this oscillator circuit. Refer to subsection 2.3 "Crystal Oscillators / Ceramic Resonators" to aid in the selection of C2 (may need to be higher) Rs (may be needed) and clock mode (wrong mode may be selected). This is especially possible for low frequency crystals, like the common 32.768 kHz. Question 3: The design runs fine, but the frequency is slightly off, what can be done to adjust this? Answer 3: Changing the value of C1 has some affect on the oscillator frequency. If a SERIES resonant crystal is used, it will resonate at a different frequency than a PARALLEL resonant crystal of the same frequency call-out. Question 4: The board works fine, then suddenly quits, or loses time. Answer 4: Other than the obvious software checks that should be done to investigate losing time, it is possible that the amplitude of the oscillator output is not high enough to reliably trigger the oscillator input. Question 5: I'm using a device with the internal RC oscillator and I have accidently erased the calibration value. What can I do? Answer 5: If the frequency of the device does not matter, you can continue to use the device. If the frequency of the device does matter, you can purchase a new windowed device, or follow the suggestion in subsection 2.5.1 "Clock Out." DS31002A-page 2-18 1997 Microchip Technology Inc. Section 2. Oscillator 2.9 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the oscillator are: Title Application Note # PIC16/17 Oscillator Design Guide AN588 Low Power Design using PIC16/17 AN606 2 Oscillator 1997 Microchip Technology Inc. DS31002A-page 2-19 PICmicro MID-RANGE MCU FAMILY 2.10 Revision History Revision A This is the initial released revision of the PICmicro oscillators description. DS31002A-page 2-20 1997 Microchip Technology Inc. M Section 3. Reset HIGHLIGHTS This section of the manual contains the following major topics: 3.1 3.2 3.3 3.4 3.5 3.6 Introduction ....................................................................................................................3-2 Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST), Brown-out Reset (BOR), and Parity Error Reset (PER).................................................3-4 Registers and Status Bit Values ...................................................................................3-10 Design Tips ..................................................................................................................3-16 Related Application Notes............................................................................................3-17 Revision History ...........................................................................................................3-18 3 Reset 1997 Microchip Technology Inc. DS31003A page 3-1 PICmicro MID-RANGE MCU FAMILY 3.1 Introduction The reset logic is used to place the device into a known state. The source of the reset can be determined by using the device status bits. The reset logic is designed with features that reduce system cost and increase system reliability. Devices differentiate between various kinds of reset: a) b) c) d) e) f) Power-on Reset (POR) MCLR reset during normal operation MCLR reset during SLEEP WDT reset during normal operation Brown-out Reset (BOR) Parity Error Reset (PER) Most registers are unaffected by a reset; their status is unknown on POR and unchanged by all other resets. The other registers are forced to a "reset state" on Power-on Reset, MCLR, WDT reset, Brown-out Reset, Parity Error Reset, and on MCLR reset during SLEEP. The on-chip parity bits that can be used to verify the contents of program memory. Most registers are not affected by a WDT wake-up, since this is viewed as the resumption of normal operation. Status bits TO, PD, POR, BOR, and PER are set or cleared differently in different reset situations as indicated in Table 3-2. These bits are used in software to determine the nature of the reset. See Table 3-4 for a full description of the reset states of all registers. A simplified block diagram of the on-chip reset circuit is shown in Figure 3-1. This block diagram is a superset of reset features. To determine the features that are available on a specific device, please refer to the device's Data Sheet. Note: While the PICmicroTM is in a reset state, the internal phase clock is held at Q1 (beginning of an instruction cycle). All new devices will have a noise filter in the MCLR reset path to detect and ignore small pulses. See parameter 30 in the "Electrical Specifications" section for pulse width specification. DS31003A-page 3-2 1997 Microchip Technology Inc. Section 3. Reset Figure 3-1: Simplified Block Diagram of a Super-set On-chip Reset Circuit VDD I/O Pull-up Enable Weak Pull-up (2) MCLRE (2) MCLR / VPP Pin (3) MCLRE Program Memory Parity MPEEN WDT Module SLEEP (2) WDT Time-out VDD rise detect Power-on Reset VDD Brown-out Reset BODEN (2) S 3 OST/PWRT OST Chip_Reset 10-bit Ripple-counter On-chip(1) RC OSC Q Reset OSC1/ CLKIN Pin R PWRT 10-bit Ripple-counter Enable PWRT (4) See Table 3-1 for time-out situations. Enable OST Note 1: 2: 3: 4: This is a separate oscillator from the RC oscillator of the CLKIN pin or the INTRC oscillator. Features in dashed boxes not available on all devices, see device's Data Sheet. In some devices, this pin may be configured as a general purpose Input. The early PICmicro devices have the configuration bit defined as PWRTE = 1 is enabled, while all other devices the configuration bit is defined as PWRTE = 0 is enabled. 1997 Microchip Technology Inc. DS31003A-page 3-3 PICmicro MID-RANGE MCU FAMILY 3.2 Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST), Brown-out Reset (BOR), and Parity Error Reset (PER) 3.2.1 Power-on Reset (POR) A Power-on Reset pulse is generated on-chip when VDD rise is detected. To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD as shown in Figure 3-2. This will eliminate external RC components usually needed to create a Power-on Reset. A minimum rise time for VDD is required. See parameter D003 and parameter D004 in the "Electrical Specifications" section for details. Figure 3-2: Using On-Chip POR VDD VDD R (1) MCLR PIC16CXXX Note: The resistor is optional. When the device exits the reset condition (begins normal operation), the device operating parameters (voltage, frequency, temperature, etc.) must be within their operating ranges, otherwise the device will not function correctly. Ensure the delay is long enough to get all operating parameters within specification. Figure 3-3 shows a possible POR circuit for a slow power supply ramp up. The external Power-on Reset circuit is only required if VDD power-up time is too slow. The diode, D, helps discharge the capacitor quickly when VDD powers down. Figure 3-3: External Power-on Reset Circuit (For Slow VDD Power-up) VDD VDD VDD D R MCLR C Note: DS31003A-page 3-4 PIC16CXXX R < 40 k is recommended to ensure that the voltage drop across R does not exceed 0.2V. A larger voltage drop will degrade VIH level on the MCLR/VPP pin. 1997 Microchip Technology Inc. Section 3. Reset 3.2.2 Power-up Timer (PWRT) The Power-up Timer provides a nominal 72 ms delay on Power-on Reset (POR) or Brown-out Reset (BOR), see parameter 33 in the "Electrical Specifications" section. The Power-up Timer operates on a dedicated internal RC oscillator. The device is kept in reset as long as the PWRT is active. The PWRT delay allows VDD to rise to an acceptable level. The power-up timer enable configuration bit can enable/disable the Power-up Timer. The Power-up Timer should always be enabled when Brown-out Reset is enabled. The polarity of the Power-up Timer configuration bit is now PWRTE = 0 for enabled, while the initial definition of the bit was PWRTE = 1 for enabled. Since all new devices will use the PWRTE = 0 for enabled, the text will describe the operation for such devices. Please refer to the individual Data Sheet to ensure the correct polarity for this bit. The power-up time delay will vary from device to device due to VDD, temperature, and process variations. See DC parameters for details. 3.2.3 Oscillator Start-up Timer (OST) The Oscillator Start-Up Timer (OST) provides a 1024 oscillator cycle delay (from OSC1 input) after the PWRT delay is over. This ensures that the crystal oscillator or resonator has started and is stable. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset, Brown-out Reset, or wake-up from SLEEP. The OST counts the oscillator pulses on the OSC1/CLKIN pin. The counter only starts incrementing after the amplitude of the signal reaches the oscillator input thresholds. This delay allows the crystal oscillator or resonator to stabilize before the device exits the OST delay. The length of the time-out is a function of the crystal/resonator frequency. Figure 3-4: Oscillator Start-up Time POR or BOR Trip Point VDD MCLR Oscillator TOSC1 TOST OST TIME_OUT TDEADTIME PWRT TIME_OUT TPWRT INTERNAL RESET Tosc1 = time for the crystal oscillator to react to an oscillation level detectable by the Oscillator Start-up Timer (OST). TOST = 1024TOSC. 1997 Microchip Technology Inc. DS31003A-page 3-5 3 Reset Figure 3-4 shows the operation of the OST circuit in conjunction with the power-up timer. For low frequency crystals this start-up time can become quite long. That is because the time it takes the low frequency oscillator to start oscillating is longer than the power-up timer's delay. So the time from when the power-up timer times-out, to when the oscillator starts to oscillate is a dead time. There is no minimum or maximum time for this dead time (TDEADTIME). PICmicro MID-RANGE MCU FAMILY 3.2.4 Power-up Sequence On power-up, the time-out sequence is as follows: First the internal POR is detected, then, if enabled, the PWRT time-out is invoked. After the PWRT time-out is over, the OST is activated. The total time-out will vary based on oscillator configuration and PWRTE bit status. For example, in RC mode with the PWRTE bit set (PWRT disabled), there will be no time-out at all. Figure 3-5, Figure 3-6 and Figure 3-7 depict time-out sequences. Since the time-outs occur from the internal POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high will begin execution immediately (Figure 3-7). This is useful for testing purposes or to synchronize more than one device operating in parallel. If the device voltage is not within the electrical specifications by the end of a time-out, the MCLR/VPP pin must be held low until the voltage is within the device specification. The use of an external RC delay is sufficient for many of these applications. Table 3-1 shows the time-outs that occur in various situations, while Figure 3-5 through Figure 3-8 show four different cases that can happen on powering up the device. Table 3-1: Time-out in Various Situations Oscillator Configuration Power-up Timer Brown-out Reset Wake-up from SLEEP Enabled Disabled XT, HS, LP 72 ms + 1024TOSC 1024TOSC 72 ms + 1024TOSC 1024TOSC RC 72 ms -- (1) 72 ms -- (1) Note 1: Devices with the Internal/External RC option have a nominal 250 s delay. Figure 3-5: Time-out Sequence on Power-up (MCLR Tied to VDD) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET DS31003A-page 3-6 1997 Microchip Technology Inc. Section 3. Reset Figure 3-6: Time-out Sequence on Power-up (MCLR not Tied to VDD): Case 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET Figure 3-7: Time-out Sequence on Power-up (MCLR not Tied to VDD): Case 2 VDD MCLR 3 INTERNAL POR TPWRT Reset PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET Figure 3-8: Slow Rise Time (MCLR Tied to VDD) 5V VDD 0V MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET 1997 Microchip Technology Inc. DS31003A-page 3-7 PICmicro MID-RANGE MCU FAMILY 3.2.5 Brown-out Reset (BOR) On-chip Brown-out Reset circuitry places the device into reset when the device voltage falls below a trip point (BVDD). This ensures that the device does not continue program execution outside the valid operation range of the device. Brown-out resets are typically used in AC line applications or large battery applications where large loads may be switched in (such as automotive), and cause the device voltage to temporarily fall below the specified operating minimum. Note: Before using the on-chip brown-out for a voltage supervisory function (monitor battery decay), please review the electrical specifications to ensure that they meet your requirements. The BODEN configuration bit can disable (if clear/programmed) or enable (if set) the Brown-out Reset circuitry. If VDD falls below BVDD (Typically 4.0V, parameter D005 in the "Electrical Specifications" section), for greater than parameter 35, the brown-out situation will reset the chip. A reset is not guaranteed to occur if VDD falls below BVDD for less than parameter 35. The chip will remain in Brown-out Reset until VDD rises above BVDD. The Power-up Timer will now be invoked and will keep the chip in reset an additional 72 ms. If VDD drops below BVDD while the Power-up Timer is running, the chip will go back into Reset and the Power-up Timer will be re-initialized. Once VDD rises above BVDD, the Power-up Timer will again start a 72 ms time delay. Figure 3-9 shows typical Brown-out situations. With the BODEN bit set, all voltages below BVDD will hold the device in the reset state. This includes during the power-up sequence. Figure 3-9: Brown-out Situations VDD BVDD Internal Reset 72 ms VDD BVDD Internal Reset <72 ms 72 ms VDD BVDD Internal Reset DS31003A-page 3-8 72 ms 1997 Microchip Technology Inc. Section 3. Reset Some devices do not have the on-chip brown-out circuit, and in other cases there are some applications where the Brown-out Reset trip point of the device may not be at the desired level. Figure 3-10 and Figure 3-11 are two examples of external circuitry that may be implemented. Each needs to be evaluated to determine if they match the requirements of the application. Figure 3-10: External Brown-out Protection Circuit 1 VDD VDD 33 k Q1 10 k MCLR 40 k PIC16CXXX This circuit will activate reset when VDD goes below (Vz + 0.7V) where Vz = Zener voltage. Note 1: Internal Brown-out Reset circuitry should be disabled when using this circuit. 2: Resistors should be adjusted for the characteristics of the transistor. Figure 3-11: External Brown-out Protection Circuit 2 VDD 3 VDD R1 Q1 MCLR 40 k Reset R2 PIC16CXXX Note 1: This brown-out circuit is less expensive, albeit less accurate. Transistor Q1 turns off when VDD is below a certain level such that: VDD * R1 R1 + R2 = 0.7V 2: Internal Brown-out Reset circuitry should be disabled when using this circuit. 3: Resistors should be adjusted for the characteristics of the transistor. 1997 Microchip Technology Inc. DS31003A-page 3-9 PICmicro MID-RANGE MCU FAMILY 3.3 Registers and Status Bit Values Table 3-2: Status Bits and Their Significance POR BOR(1) TO PD 0 x 1 1 Power-on Reset 0 x 0 x Illegal, TO is set on POR 0 x x 0 Illegal, PD is set on POR 1(2) 0 1 1 Brown-out Reset 1(2) 1(2) 0 1 WDT Reset 1(2) 1(2) 0 0 WDT Wake-up 1(2) 1(2) u u MCLR reset during normal operation 1(2) 1(2) 1 0 MCLR reset during SLEEP Condition Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0'. Note 1: Not all devices have BOR circuitry. 2: These bits are unchanged for the given conditions, and when initialized (set) after a POR or a BOR will read as a '1'. DS31003A-page 3-10 1997 Microchip Technology Inc. Section 3. Reset Table 3-3: Initialization Condition for Special Registers Program Counter STATUS Register PCON Register Power-on Reset 000h 0001 1xxx u--- -10x MCLR reset during normal operation 000h 000u uuuu u--- -uuu MCLR reset during SLEEP 000h 0001 0uuu u--- -uuu WDT reset 000h 0000 1uuu u--- -uuu PC + 1 uuu0 0uuu u--- -uuu 000h 0001 1uuu u--- -uu0 PC + 1(1) uuu1 0uuu u--- -uuu Condition WDT Wake-up Brown-out Reset Interrupt Wake-up from SLEEP Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0'. Note 1: When the wake-up is due to an interrupt and global enable bit, GIE, is set the PC is loaded with the interrupt vector (0004h) after execution of PC+1. 2: If a status bit is not implemented, that bit will be read as `0'. 3 Reset 1997 Microchip Technology Inc. DS31003A-page 3-11 PICmicro MID-RANGE MCU FAMILY Table 3-4: Initialization Conditions for Special Function Registers Wake-up from SLEEP through: - interrupt - WDT time-out Register Power-on Reset Brown-out Reset MCLR Reset during: - normal operation - SLEEP or WDT Reset ADCAPL 0000 0000 0000 0000 uuuu uuuu ADCAPH 0000 0000 0000 0000 uuuu uuuu ADCON0 0000 00-0 0000 00-0 uuuu uu-u ADCON1 ---- -000 ---- -000 ---- -uuu ADRES xxxx xxxx uuuu uuuu uuuu uuuu ADTMRL 0000 0000 0000 0000 uuuu uuuu ADMRH 0000 0000 0000 0000 uuuu uuuu CCP1CON --00 0000 --00 0000 --uu uuuu CCP2CON 0000 0000 0000 0000 uuuu uuuu CCPR1L xxxx xxxx uuuu uuuu uuuu uuuu CCPR1H xxxx xxxx uuuu uuuu uuuu uuuu CCPR2L xxxx xxxx uuuu uuuu uuuu uuuu CCPR2H xxxx xxxx uuuu uuuu uuuu uuuu CMCON 00-- 0000 00-- 0000 uu-- uuuu EEADR xxxx xxxx uuuu uuuu uuuu uuuu EECON1 ---0 x000 ---0 q000 ---0 uuuu EECON2 - - - EEDATA xxxx xxxx uuuu uuuu uuuu uuuu FSR xxxx xxxx uuuu uuuu uuuu uuuu GPIO --xx xxxx --uu uuuu --uu uuuu I2CADD 0000 0000 0000 0000 uuuu uuuu I2CBUF xxxx xxxx uuuu uuuu uuuu uuuu I2CCON 0000 0000 0000 0000 uuuu uuuu I2CSTAT --00 0000 --00 0000 --uu uuuu - - - INTCON 0000 000x 0000 000u uuuu uuuu(1) LCDCON 00-0 0000 00-0 0000 uu-u uuuu LCDD00 to LCDD15 xxxx xxxx uuuu uuuu uuuu uuuu LCDPS ---- 0000 ---- 0000 ---- uuuu LCDSE 1111 1111 1111 1111 uuuu uuuu OPTION_REG 1111 1111 1111 1111 uuuu uuuu OSCCAL 0111 00-- uuuu uu-- uuuu uu-- PCL 0000 0000 0000 0000 PC + 1(2) PCLATH ---0 0000 ---0 0000 ---u uuuu PCON ---- --0u ---- --uu ---- --uu PIE1 0000 0000 0000 0000 uuuu uuuu PIE2 ---- ---0 ---- ---0 ---- ---u PIR1 0000 0000 0000 0000 uuuu uuuu INDF Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0',q = value depends on condition. Note 1: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 3-3 for reset value for specific condition. DS31003A-page 3-12 1997 Microchip Technology Inc. Section 3. Reset Table 3-4: Initialization Conditions for Special Function Registers (Cont.'d) Wake-up from SLEEP through: - interrupt - WDT time-out MCLR Reset during: - normal operation - SLEEP or WDT Reset PIR2 ---- ---0 ---- ---0 ---- ---u PORTA --xx xxxx --uu uuuu --uu uuuu PORTB xxxx xxxx uuuu uuuu uuuu uuuu PORTC xxxx xxxx uuuu uuuu uuuu uuuu PORTD xxxx xxxx uuuu uuuu uuuu uuuu PORTE ---- -xxx ---- -uuu ---- -uuu PORTF 0000 0000 0000 0000 uuuu uuuu PORTG 0000 0000 0000 0000 uuuu uuuu PR2 1111 1111 1111 1111 1111 1111 PREFA 0000 0000 0000 0000 uuuu uuuu PREFB 0000 0000 0000 0000 uuuu uuuu RCSTA 0000 -00x 0000 -00x uuuu -uuu RCREG 0000 0000 0000 0000 uuuu uuuu SLPCON 0011 1111 0011 1111 uuuu uuuu SPBRG 0000 0000 0000 0000 uuuu uuuu SSPBUF xxxx xxxx uuuu uuuu uuuu uuuu SSPCON 0000 0000 0000 0000 uuuu uuuu SSPADD 0000 0000 0000 0000 uuuu uuuu SSPSTAT 0000 0000 0000 0000 uuuu uuuu STATUS 0001 1xxx 000q quuu(3) uuuq quuu(3) T1CON --00 0000 --uu uuuu --uu uuuu T2CON -000 0000 -000 0000 -uuu uuuu TMR0 xxxx xxxx uuuu uuuu uuuu uuuu TMR1L xxxx xxxx uuuu uuuu uuuu uuuu TMR1H xxxx xxxx uuuu uuuu uuuu uuuu TMR2 0000 0000 0000 0000 uuuu uuuu TRIS --11 1111 --11 1111 --uu uuuu TRISA --11 1111 --11 1111 --uu uuuu TRISB 1111 1111 1111 1111 uuuu uuuu TRISC 1111 1111 1111 1111 uuuu uuuu TRISD 1111 1111 1111 1111 uuuu uuuu TRISE 0000 -111 0000 -111 uuuu -uuu TRISF 1111 1111 1111 1111 uuuu uuuu TRISG 1111 1111 1111 1111 uuuu uuuu TXREG 0000 0000 0000 0000 uuuu uuuu TXSTA 0000 -010 0000 -010 uuuu -uuu VRCON 000- 0000 000- 0000 uuu- uuuu W xxxx xxxx uuuu uuuu uuuu uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as `0',q = value depends on condition. Note 1: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 3-3 for reset value for specific condition. 1997 Microchip Technology Inc. DS31003A-page 3-13 3 Reset Power-on Reset Brown-out Reset Register PICmicro MID-RANGE MCU FAMILY 3.3.1 Power Control (PCON) and STATUS Registers The Power Control (PCON) register contains a status bit to allow differentiation between a Power-on Reset (POR) to an external MCLR Reset or WDT Reset. It also contains a status bit to determine if a Brown-out Reset (BOR) occurred. The power control/status register, PCON has up to four bits. The BOR (Brown-out Reset) bit, is unknown on a Power-on-reset. It must initially be set by the user and checked on subsequent resets to see if BOR = '0' indicating that a Brown-out Reset has occurred. The BOR status bit is a "don't care" bit and is not necessarily predictable if the brown-out circuit is disabled (by clearing the BODEN bit in the Configuration word). The POR (Power-on Reset) bit, is cleared on a Power-on Reset and is unaffected otherwise. The user sets this bit following a Power-on Reset. On subsequent resets if POR is `0', it will indicate that a Power-on Reset must have occurred. The PER (Parity Error Reset) bit, is cleared on a Parity Error Reset and must be set by user software. It will also be set on a Power-on Reset. The MPEEN (Memory Parity Error Enable) bit, reflects the status of the MPEEN bit in configuration word. It is unaffected by any reset or interrupt. Note: BOR is unknown on Power-on Reset. It must then be set by the user and checked on subsequent resets to see if BOR is clear, indicating a brown-out has occurred. The BOR status bit is a don't care and is not necessarily predictable if the brown-out circuit is disabled (by clearing the BODEN bit in the Configuration word). Register 3-1: PCON Register R-u MPEEN bit 7 U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 PER R/W-0 POR R/W-0 BOR bit 0 bit 7 MPEEN: Memory Parity Error Circuitry Status bit This bit reflects the value of the MPEEN configuration bit. bit 6:3 Unimplemented: Read as '0' bit 2 PER: Memory Parity Error Reset Status bit 1 = No parity error reset occurred 0 = A program memory fetch parity error occurred (must be set in software after a Power-on Reset or Parity Error Reset occurs) bit 1 POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset or Power-on Reset occurs) Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Note: DS31003A-page 3-14 u = unchanged bit - n = Value at POR reset Not all bits may be implemented. 1997 Microchip Technology Inc. Section 3. Reset The STATUS register contains two bits (TO and PD), which when used in conjunction with the PCON register bits provide the user with enough information to determine the cause of the reset. Register 3-2: STATUS Register R/W-0 IRP bit 7 bit 7 R/W-0 RP1 R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC R/W-x C bit 0 IRP: Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h - 1FFh) 0 = Bank 0, 1 (00h - FFh) For devices with only Bank0 and Bank1 the IRP bit is reserved, always maintain this bit clear. bit 6:5 RP1:RP0: Register Bank Select bits (used for direct addressing) 11 = Bank 3 (180h - 1FFh) 10 = Bank 2 (100h - 17Fh) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes. For devices with only Bank0 and Bank1 the IRP bit is reserved, always maintain this bit clear. bit 4 TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit carry/borrow bit (ADDWF, ADDLW, SUBLW, SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0 C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred For borrow the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31003A-page 3-15 Reset Note: 3 PICmicro MID-RANGE MCU FAMILY 3.4 Design Tips Question 1: When my system is subjected to an environment with ESD and EMI, it operates erratically. Answer 1: If the device you are using does not have filtering to the on-chip master clear circuit (Appendix C), ensure that proper external filtering is placed on the MCLR pin to remove narrow pulses. Electrical Specification parameter 35 specifies the pulse width required to cause a reset. Question 2: With JW (windowed) devices my system resets and operates properly. With an OTP device, my system does not operate properly. Answer 2: The most common reason for this is that the windowed device (JW) has not had its window covered. The background light causes the device to power-up in a different state than would typically be seen in a device where no light is present. In most cases all the General Purpose RAM and Special Function Registers were not initialized properly. DS31003A-page 3-16 1997 Microchip Technology Inc. Section 3. Reset 3.5 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Resets are: Title Application Note # Power-up Trouble Shooting AN607 Power-up Considerations AN522 3 Reset 1997 Microchip Technology Inc. DS31003A-page 3-17 PICmicro MID-RANGE MCU FAMILY 3.6 Revision History Revision A This is the initial released revision of the Reset description. DS31003A-page 3-18 1997 Microchip Technology Inc. M Section 4. Architecture HIGHLIGHTS This section of the manual contains the following major topics: 4.1 4.2 4.3 4.4 4.5 4.6 4.7 Introduction ....................................................................................................................4-2 Clocking Scheme/Instruction Cycle ...............................................................................4-5 Instruction Flow/Pipelining .............................................................................................4-6 I/O Descriptions .............................................................................................................4-7 Design Tips ..................................................................................................................4-12 Related Application Notes............................................................................................4-13 Revision History ...........................................................................................................4-14 4 Architecture 1997 Microchip Technology Inc. DS31004A page 4-1 PICmicro MID-RANGE MCU FAMILY 4.1 Introduction The high performance of the PICmicroTM devices can be attributed to a number of architectural features commonly found in RISC microprocessors. These include: * * * * * * * * Harvard architecture Long Word Instructions Single Word Instructions Single Cycle Instructions Instruction Pipelining Reduced Instruction Set Register File Architecture Orthogonal (Symmetric) Instructions Figure 4-2 shows a simple core memory bus arrangement for Mid-Range MCU devices. Harvard Architecture: Harvard architecture has the program memory and data memory as separate memories and are accessed from separate buses. This improves bandwidth over traditional von Neumann architecture in which program and data are fetched from the same memory using the same bus. To execute an instruction, a von Neumann machine must make one or more (generally more) accesses across the 8-bit bus to fetch the instruction. Then data may need to be fetched, operated on, and possibly written. As can be seen from this description, that bus can be extremely conjested. While with a Harvard architecture, the instruction is fetched in a single instruction cycle (all 14-bits). While the program memory is being accessed, the data memory is on an independent bus and can be read and written. These separated buses allow one instruction to execute while the next instruction is fetched. A comparison of Harvard vs. von-Neumann architectures is shown in Figure 4-1. Figure 4-1: Harvard vs. von Neumann Block Architectures von-Neumann Harvard Data Memory 8 CPU 14 Program Memory CPU 8 Program and Data Memory Long Word Instructions: Long word instructions have a wider (more bits) instruction bus than the 8-bit Data Memory Bus. This is possible because the two buses are separate. This further allows instructions to be sized differently than the 8-bit wide data word which allows a more efficient use of the program memory, since the program memory width is optimized to the architectural requirements. Single Word Instructions: Single Word instruction opcodes are 14-bits wide making it possible to have all single word instructions. A 14-bit wide program memory access bus fetches a 14-bit instruction in a single cycle. With single word instructions, the number of words of program memory locations equals the number of instructions for the device. This means that all locations are valid instructions. Typically in the von Neumann architecture, most instructions are multi-byte. In general, a device with 4-KBytes of program memory would allow approximately 2K of instructions. This 2:1 ratio is generalized and dependent on the application code. Since each instruction may take multiple bytes, there is no assurance that each location is a valid instruction. DS31004A-page 4-2 1997 Microchip Technology Inc. Section 4. Architecture Instruction Pipeline: The instruction pipeline is a two-stage pipeline which overlaps the fetch and execution of instructions. The fetch of the instruction takes one TCY, while the execution takes another TCY. However, due to the overlap of the fetch of current instruction and execution of previous instruction, an instruction is fetched and another instruction is executed every single TCY. Single Cycle Instructions: With the Program Memory bus being 14-bits wide, the entire instruction is fetched in a single machine cycle (TCY). The instruction contains all the information required and is executed in a single cycle. There may be a one cycle delay in execution if the result of the instruction modified the contents of the Program Counter. This requires the pipeline to be flushed and a new instruction to be fetched. Reduced Instruction Set: When an instruction set is well designed and highly orthogonal (symmetric), fewer instructions are required to perform all needed tasks. With fewer instructions, the whole set can be more rapidly learned. Register File Architecture: The register files/data memory can be directly or indirectly addressed. All special function registers, including the program counter, are mapped in the data memory. Orthogonal (Symmetric) Instructions: Orthogonal instructions make it possible to carry out any operation on any register using any addressing mode. This symmetrical nature and lack of "special instructions" make programming simple yet efficient. In addition, the learning curve is reduced significantly. The mid-range instruction set uses only two non-register oriented instructions, which are used for two of the cores features. One is the SLEEP instruction which places the device into the lowest power use mode. The other is the CLRWDT instruction which verifies the chip is operating properly by preventing the on-chip Watchdog Timer (WDT) from overflowing and resetting the device. 4 Architecture 1997 Microchip Technology Inc. DS31004A-page 4-3 PICmicro MID-RANGE MCU FAMILY Figure 4-2: General Mid-range PICmicro Block Diagram 13 Program Bus EPROM Program Counter Program Memory up to 8K x 14 8 Level Stack (13-bit) 14 8 Data Bus PORTA RA0 RA1 RA2 RA3 RA4 RA5 RAM File Registers up to 368 x 8 RAM Addr (1) PORTB 9 Addr MUX Instruction reg Direct Addr 7 8 Indirect Addr FSR reg STATUS reg 8 3 Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Internal RC clock (2) Oscillator Start-up Timer Power-on Reset Watchdog Timer Brown-out Reset (2) MCLR Timer0 Timer1 RC0 RC1 RC2 RC3 RC4 RC5 RC6 RC7 MUX ALU 8 PORTD W reg PORTE VDD, VSS Timer2 PORTC RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7 RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 RE0 RE1 RE2 RE3 RE4 RE5 RE6 RE7 A/D PORTF CCPs Comparators Other Modules Voltage Reference Peripheral Modules (Note 3) Synchronous Serial Port USARTs Parallel Slave Port LCD Drivers Data EEPROM up to 256 x 8 RF0 RF1 RF2 RF3 RF4 RF5 RF6 RF7 PORTG RG0 RG1 RG2 RG3 RG4 RG5 RG6 RG7 General Purpose I/O (Note 3) Note 1: The high order bits of the Direct Address for the RAM are from the STATUS register. 2: Not all devices have this feature, please refer to device data sheet. 3: Many of the general purpose I/O pins are multiplexed with one or more peripheral module functions. The multiplexing combinations are device dependent. DS31004A-page 4-4 1997 Microchip Technology Inc. Section 4. Architecture 4.2 Clocking Scheme/Instruction Cycle The clock input (from OSC1) is internally divided by four to generate four non-overlapping quadrature clocks, namely Q1, Q2, Q3, and Q4. Internally, the program counter (PC) is incremented every Q1, and the instruction is fetched from the program memory and latched into the instruction register in Q4. The instruction is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow are illustrated in Figure 4-3, and Example 4-1. Figure 4-3: Clock/Instruction Cycle TCY1 Q1 Q2 Q3 TCY2 Q4 Q1 Q2 Q3 TCY3 Q4 Q1 Q2 Q3 Q4 OSC1 Q1 Q2 Internal phase clock Q3 Q4 PC PC PC+1 PC+2 OSC2/CLKOUT (RC mode) Fetch INST (PC) Execute INST (PC-1) Fetch INST (PC+1) Execute INST (PC) Fetch INST (PC+2) Execute INST (PC+1) 4 Architecture 1997 Microchip Technology Inc. DS31004A-page 4-5 PICmicro MID-RANGE MCU FAMILY 4.3 Instruction Flow/Pipelining An "Instruction Cycle" consists of four Q cycles (Q1, Q2, Q3, and Q4). Fetch takes one instruction cycle while decode and execute takes another instruction cycle. However, due to Pipelining, each instruction effectively executes in one cycle. If an instruction causes the program counter to change (e.g. GOTO) then an extra cycle is required to complete the instruction (Example 4-1). The instruction fetch begins with the program counter incrementing in Q1. In the execution cycle, the fetched instruction is latched into the "Instruction Register (IR)" in cycle Q1. This instruction is then decoded and executed during the Q2, Q3, and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). Example 4-1 shows the operation of the two stage pipeline for the instruction sequence shown. At time TCY0, the first instruction is fetched from program memory. During TCY1, the first instruction executes while the second instruction is fetched. During TCY2, the second instruction executes while the third instruction is fetched. During TCY3, the fourth instruction is fetched while the third instruction (CALL SUB_1) is executed. When the third instruction completes execution, the CPU forces the address of instruction four onto the Stack and then changes the Program Counter (PC) to the address of SUB_1. This means that the instruction that was fetched during TCY3 needs to be "flushed" from the pipeline. During TCY4, instruction four is flushed (executed as a NOP) and the instruction at address SUB_1 is fetched. Finally during TCY5, instruction five is executed and the instruction at address SUB_1 + 1 is fetched. Example 4-1: Instruction Pipeline Flow 1. MOVLW 55h TCY0 TCY1 Fetch 1 Execute 1 2. MOVWF PORTB 3. CALL SUB_1 4. BSF PORTA, BIT3 (Forced NOP) 5. Instruction @ address SUB_1 Fetch 2 TCY2 TCY3 TCY4 TCY5 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush Fetch SUB_1 Execute SUB_1 Fetch SUB_1 + 1 All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction is "flushed" from the pipeline while the new instruction is being fetched and then executed. DS31004A-page 4-6 1997 Microchip Technology Inc. Section 4. Architecture 4.4 I/O Descriptions Table 4-1 gives a brief description of the functions that may be multiplexed to a port pin. Multiple functions may exist on one port pin. When multiplexing occurs, the peripheral module's functional requirements may force an override of the data direction (TRIS bit) of the port pin (such as in the A/D and LCD modules). Table 4-1: Pin Name I/O Descriptions Pin Type Buffer Type I I I I I I I I I I I I I I I I P P I I I/O I/O O Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog Analog P P Analog Analog ST ST Analog Description Analog Input Channels AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AVDD AVSS C1 C2 CCP1 CCP2 CDAC 1997 Microchip Technology Inc. DS31004A-page 4-7 4 Architecture Analog Power Analog Ground LCD Voltage Generation LCD Voltage Generation Capture1 input/Compare1 output/PWM1 output Capture2 input/Compare2 output/PWM2 output. A/D ramp current source output. Normally connected to external capacitor to generate a linear voltage ramp. CK I/O ST USART Synchronous Clock, always associated with TX pin function (See related TX, RX, DT) CLKIN I ST/CMOS External clock source input. Always associated with pin function OSC1. (See related OSC1/CLKIN, OSC2/CLKOUT pins) CLKOUT O -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. Always associated with OSC2 pin function. (See related OSC2, OSC1) CMPA O -- Comparator A output CMPB O -- Comparator B output Legend: TTL = TTL-compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels SM = SMBus compatible input. An external resistor is required if this pin is used as an output NPU = N-channel pull-up PU = Weak internal pull-up No-P diode = No P-diode to VDD AN = Analog input or output I = input O = output P = Power L = LCD Driver PICmicro MID-RANGE MCU FAMILY Table 4-1: I/O Descriptions (Cont.'d) Pin Type Buffer Type L L L L -- -- -- -- CS DT I I/O TTL ST GP0 I/O TTL/ST GP1 I/O TTL/ST GP2 GP3 GP4 GP5 INT MCLR/VPP I/O I I/O I/O I I/P ST TTL TTL TTL ST ST NC OSC1 -- I -- ST/CMOS OSC2 O -- PBTN PSP0 PSP1 PSP2 PSP3 PSP4 PSP5 PSP6 PSP7 I I/O I/O I/O I/O I/O I/O I/O I/O ST TTL TTL TTL TTL TTL TTL TTL TTL Pin Name COM0 COM1 COM2 COM3 Description LCD Common Driver0 LCD Common Driver1 LCD Common Driver2 LCD Common Driver3 chip select control for parallel slave port (See related RD and WR) USART Synchronous Data. Always associated RX pin function. (See related RX, TX, CK) GP is a bi-directional I/O port. Some pins of port GP can be software programmed for internal weak pull-ups on the inputs. TTL input buffer as general purpose I/O, Schmitt Trigger input buffer when used as the serial programming mode. TTL input buffer as general purpose I/O, Schmitt Trigger input buffer when used as the serial programming mode. External Interrupt Master clear (reset) input or programming voltage input. This pin is an active low reset to the device. These pins should be left unconnected. Oscillator crystal input or external clock source input. ST buffer when configured in RC mode. CMOS otherwise. Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. Input with weak pull-up resistor, can be used to generate an interrupt. Parallel Slave Port for interfacing to a microprocessor port. These pins have TTL input buffers when PSP module is enabled. PORTA is a bi-directional I/O port. RA0 I/O TTL RA1 I/O TTL RA2 I/O TTL RA3 I/O TTL RA4 I/O ST RA4 is an open drain when configured as output. RA5 I/O TTL Legend: TTL = TTL-compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels SM = SMBus compatible input. An external resistor is required if this pin is used as an output NPU = N-channel pull-up PU = Weak internal pull-up No-P diode = No P-diode to VDD AN = Analog input or output I = input O = output P = Power L = LCD Driver DS31004A-page 4-8 1997 Microchip Technology Inc. Section 4. Architecture Table 4-1: Pin Name I/O Descriptions (Cont.'d) Pin Type Buffer Type Description PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-ups on all inputs. I/O I/O I/O I/O I/O I/O I/O TTL TTL TTL TTL TTL TTL TTL/ST RB7 I/O TTL/ST RC0 RC1 RC2 RC3 RC4 RC5 RC6 RC7 RD I/O I/O I/O I/O I/O I/O I/O I/O I ST ST ST ST ST ST ST ST TTL RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 I/O I/O I/O I/O I/O I/O I/O I/O ST ST ST ST ST ST ST ST Interrupt on change pin. Interrupt on change pin. Interrupt on change pin. Serial programming clock. TTL input buffer as general purpose I/O, Schmitt Trigger input buffer when used as the serial programming clock. Interrupt on change pin. Serial programming data. TTL input buffer as general purpose I/O, Schmitt Trigger input buffer when used as the serial programming data. PORTC is a bi-directional I/O port. Read control for parallel slave port (See also WR and CS pins) PORTD is a bi-directional I/O port. 4 PORTE is a bi-directional I/O port. RE0 I/O ST RE1 I/O ST RE2 I/O ST RE3 I/O ST RE4 I/O ST RE5 I/O ST RE6 I/O ST RE7 I/O ST Legend: TTL = TTL-compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels SM = SMBus compatible input. An external resistor is required if this pin is used as an output NPU = N-channel pull-up PU = Weak internal pull-up No-P diode = No P-diode to VDD AN = Analog input or output I = input O = output P = Power L = LCD Driver 1997 Microchip Technology Inc. DS31004A-page 4-9 Architecture RB0 RB1 RB2 RB3 RB4 RB5 RB6 PICmicro MID-RANGE MCU FAMILY Table 4-1: I/O Descriptions (Cont.'d) Pin Type Buffer Type REFA REFB O O CMOS CMOS RF0 RF1 RF2 RF3 RF4 RF5 RF6 RF7 I/O I/O I/O I/O I/O I/O I/O I/O ST ST ST ST ST ST ST ST RG0 RG1 RG2 RG3 RG4 RG5 RG6 RG7 RX SCL SCLA SCLB SDA SDAA SDAB SCK SDI SDO SS SEG00 to SEG31 SUM I/O I/O I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I/O I O I I/L ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST ST -- ST ST O AN Pin Name Description Programmable reference A output. Programmable reference B output. PORTF is a digital input or LCD Segment Driver Port PORTG is a digital input or LCD Segment Driver Port USART Asynchronous Receive Synchronous serial clock input/output for I2C mode. Synchronous serial clock for I2C interface. Synchronous serial clock for I2C interface. I2CTM Data I/O Synchronous serial data I/O for I2C interface Synchronous serial data I/O for I2C interface Synchronous serial clock input/output for SPI mode. SPI Data In SPI Data Out (SPI mode) SPI Slave Select input LCD Segment Driver00 through Driver31. AN1 summing junction output. This pin can be connected to an external capacitor for averaging small duration pulses. T0CKI I ST Timer0 external clock input T1CKI I ST Timer1 external clock input T1OSO O CMOS Timer1 oscillator output T1OSI I CMOS Timer1 oscillator input TX O -- USART Asynchronous Transmit (See related RX) Legend: TTL = TTL-compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels SM = SMBus compatible input. An external resistor is required if this pin is used as an output NPU = N-channel pull-up PU = Weak internal pull-up No-P diode = No P-diode to VDD AN = Analog input or output I = input O = output P = Power L = LCD Driver I2C is a trademark of Philips Corporation. DS31004A-page 4-10 1997 Microchip Technology Inc. Section 4. Architecture Table 4-1: Pin Name VLCD1 VLCD2 VLCD3 VLCDADJ VREF I/O Descriptions (Cont.'d) Pin Type Buffer Type P P P I I -- -- -- Analog Analog Description LCD Voltage LCD Voltage LCD Voltage LCD Voltage Generation Analog High Voltage Reference input. DR reference voltage output on devices with comparators. I Analog Analog High Voltage Reference input. VREF+ Usually multiplexed onto an analog pin. VREFI Analog Analog Low Voltage Reference input. Usually multiplexed onto an analog pin. VREG O -- This pin is an output to control the gate of an external N-FET for voltage regulation. VSS P -- Ground reference for logic and I/O pins. VDD P -- Positive supply for logic and I/O pins. WR I TTL Write control for parallel slave port (See CS and RD pins also). Legend: TTL = TTL-compatible input CMOS = CMOS compatible input or output ST = Schmitt Trigger input with CMOS levels SM = SMBus compatible input. An external resistor is required if this pin is used as an output NPU = N-channel pull-up PU = Weak internal pull-up No-P diode = No P-diode to VDD AN = Analog input or output I = input O = output P = Power L = LCD Driver 4 Architecture 1997 Microchip Technology Inc. DS31004A-page 4-11 PICmicro MID-RANGE MCU FAMILY 4.5 Design Tips No related design tips at this time. DS31004A-page 4-12 1997 Microchip Technology Inc. Section 4. Architecture 4.6 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Architecture are: Title Application Note # No related application notes at this time. 4 Architecture 1997 Microchip Technology Inc. DS31004A-page 4-13 PICmicro MID-RANGE MCU FAMILY 4.7 Revision History Revision A This is the initial released revision of the PICmicro's Architecture description. DS31004A-page 4-14 1997 Microchip Technology Inc. M Section 5. CPU and ALU HIGHLIGHTS This section of the manual contains the following major topics: 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 Introduction ....................................................................................................................5-2 General Instruction Format ............................................................................................5-4 Central Processing Unit (CPU) ......................................................................................5-4 Instruction Clock ............................................................................................................5-4 Arithmetic Logical Unit (ALU).........................................................................................5-5 STATUS Register ...........................................................................................................5-6 OPTION_REG Register .................................................................................................5-8 PCON Register ..............................................................................................................5-9 Design Tips ..................................................................................................................5-10 Related Application Notes............................................................................................5-11 Revision History ...........................................................................................................5-12 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A page 5-1 PICmicro MID-RANGE MCU FAMILY 5.1 Introduction The Central Processing Unit (CPU) is responsible for using the information in the program memory (instructions) to control the operation of the device. Many of these instructions operate on data memory. To operate on data memory, the Arithmetic Logical Unit (ALU) is required. In addition to performing arithmetical and logical operations, the ALU controls status bits (which are found in the STATUS register). The result of some instructions force status bits to a value depending on the state of the result. The machine codes that the CPU recognizes are show in Table 5-1 (as well as the instruction mnemonics that the MPASM uses to generate these codes). DS31005A-page 5-2 1997 Microchip Technology Inc. Section 5. CPU and ALU Table 5-1: Mid-Range MCU Instruction Set Mnemonic, Operands 14-Bit Instruction Word Description Cycles MSb LSb Status Bits Notes Affected BYTE-ORIENTED FILE REGISTER OPERATIONS 1,2 C,DC,Z ffff 0111 dfff 00 1 Add W and f f, d ADDWF 1,2 Z ffff 0101 dfff 00 1 AND W with f f, d ANDWF 2 Z ffff 0001 lfff 00 1 Clear f f CLRF Z xxxx 0001 0xxx 00 1 Clear W CLRW 1,2 Z ffff 1001 dfff 00 1 Complement f f, d COMF 1,2 Z ffff 0011 dfff 00 1 Decrement f f, d DECF 1,2,3 ffff 1011 dfff 00 1(2) Decrement f, Skip if 0 f, d DECFSZ 1,2 Z ffff 1010 dfff 00 1 Increment f f, d INCF 1,2,3 ffff 1111 dfff 00 1(2) Increment f, Skip if 0 f, d INCFSZ 1,2 Z ffff 0100 dfff 00 1 Inclusive OR W with f f, d IORWF 1,2 Z ffff 1000 dfff 00 1 Move f f, d MOVF ffff 0000 lfff 00 1 Move W to f f MOVWF 0000 0000 0xx0 00 1 No Operation NOP 1,2 C ffff 1101 dfff 00 1 Rotate Left f through Carry f, d RLF 1,2 C ffff 1100 dfff 00 1 Rotate Right f through Carry f, d RRF 1,2 C,DC,Z ffff 0010 dfff 00 1 Subtract W from f f, d SUBWF 1,2 ffff 1110 dfff 00 1 Swap nibbles in f f, d SWAPF 1,2 Z ffff 0110 dfff 00 1 Exclusive OR W with f f, d XORWF BIT-ORIENTED FILE REGISTER OPERATIONS 1,2 ffff 00bb bfff 01 1 Bit Clear f f, b BCF 1,2 ffff 01bb bfff 01 1 Bit Set f f, b BSF 3 10bb bfff- ffff 01 1 (2) Bit Test f, Skip if Clear f, b BTFSC 3 ffff 11bb bfff 01 1 (2) Bit Test f, Skip if Set f, b BTFSS LITERAL AND CONTROL OPERATIONS C,DC,Z kkkk 111x kkkk 11 1 Add literal and W k ADDLW Z kkkk 1001 kkkk 11 1 AND literal with W k ANDLW kkkk 0kkk kkkk 10 2 Call subroutine k CALL TO,PD 0100 0000 0110 00 1 Clear Watchdog Timer CLRWDT kkkk 1kkk kkkk 10 2 Go to address k GOTO kkkk 1000 kkkk 11 1 Inclusive OR literal with W k IORLW Z kkkk 00xx kkkk 11 1 Move literal to W k MOVLW 1001 0000 0000 00 2 Return from interrupt RETFIE kkkk 01xx kkkk 11 2 Return with literal in W k RETLW 1000 0000 0000 00 2 Return from Subroutine RETURN 0011 0000 0110 00 1 Go into standby mode SLEEP TO,PD kkkk 110x kkkk 11 1 Subtract W from literal k SUBLW C,DC,Z kkkk 1010 kkkk 11 1 Exclusive OR literal with W k XORLW Z Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A-page 5-3 PICmicro MID-RANGE MCU FAMILY 5.2 General Instruction Format The Mid-Range MCU instructions can be broken down into four general formats as shown in Figure 5-1. As can be seen the opcode for the instruction varies from 3-bits to 6-bits. This variable opcode size is what allows 35 instructions to be implemented. Figure 5-1: General Format for Instructions Byte-oriented file register operations 13 8 7 6 OPCODE d f (FILE #) 0 Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) f (FILE #) 0 d = 0 for destination W d = 1 for destination f f = 7-bit file register address b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 8 7 OPCODE 0 k = 8-bit immediate value k (literal) CALL and GOTO instructions only 13 11 10 0 OPCODE 5.3 k = 11-bit immediate value k (literal) Central Processing Unit (CPU) The CPU can be thought of as the "brains" of the device. It is responsible for fetching the correct instruction for execution, decoding that instruction, and then executing that instruction. The CPU sometimes works in conjunction with the ALU to complete the execution of the instruction (in arithmetic and logical operations). The CPU controls the program memory address bus, the data memory address bus, and accesses to the stack. 5.4 Instruction Clock Each instruction cycle (TCY) is comprised of four Q cycles (Q1-Q4). The Q cycle time is the same as the device oscillator cycle time (TOSC). The Q cycles provide the timing/designation for the Decode, Read, Process Data, Write, etc., of each instruction cycle. The following diagram shows the relationship of the Q cycles to the instruction cycle. The four Q cycles that make up an instruction cycle (TCY) can be generalized as: Q1: Instruction Decode Cycle or forced No operation Q2: Instruction Read Data Cycle or No operation Q3: Process the Data Q4: Instruction Write Data Cycle or No operation Each instruction will show a detailed Q cycle operation for the instruction. Figure 5-2: Q Cycle Activity Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Tosc TCY1 DS31005A-page 5-4 TCY2 TCY3 1997 Microchip Technology Inc. Section 5. CPU and ALU 5.5 Arithmetic Logical Unit (ALU) PICmicro MCUs contain an 8-bit ALU and an 8-bit working register. The ALU is a general purpose arithmetic and logical unit. It performs arithmetic and Boolean functions between the data in the working register and any register file. Figure 5-3: Operation of the ALU and W Register 8-bit literal (from instruction word) 8 W Register 8 8-bit register value 8 (from direct or indirect address of instruction) 8 ALU Register File Special Function Registers (SFR's) and General Purpose RAM (GPR) 8 d bit, or from instruction d = '0' or Literal Instructions d = '1' The ALU is 8-bits wide and is capable of addition, subtraction, shift and logical operations. Unless otherwise mentioned, arithmetic operations are two's complement in nature. In two-operand instructions, typically one operand is the working register (W register). The other operand is a file register or an immediate constant. In single operand instructions, the operand is either the W register or a file register. The W register is an 8-bit working register used for ALU operations. It is not an addressable register. Depending on the instruction executed, the ALU may affect the values of the Carry (C), Digit Carry (DC), and Zero (Z) bits in the STATUS register. The C and DC bits operate as a borrow bit and a digit borrow out bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples. 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A-page 5-5 PICmicro MID-RANGE MCU FAMILY 5.6 STATUS Register The STATUS register, shown in Figure 5-1, contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory. Since the selection of the Data Memory banks is controlled by this register, it is required to be present in every bank. Also, this register is in the same relative position (offset) in each bank (see Figure 6-5: "Register File Map" in the "Memory Organization" section). The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register because these instructions do not affect the Z, C or DC bits from the STATUS register. For other instructions, not affecting any status bits, see Table 5-1. Note 1: Some devices do not require the IRP and RP1 (STATUS<7:6>) bits. These bits are not used by the Section 5. CPU and ALU and should be maintained clear. Use of these bits as general purpose R/W bits is NOT recommended, since this may affect upward code compatibility with future products. Note 2: The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction. DS31005A-page 5-6 1997 Microchip Technology Inc. Section 5. CPU and ALU Register 5-1: STATUS Register R/W-0 IRP bit 7 bit 7 R/W-0 RP1 R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC R/W-x C bit 0 IRP: Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h - 1FFh) 0 = Bank 0, 1 (00h - FFh) For devices with only Bank0 and Bank1 the IRP bit is reserved, always maintain this bit clear. bit 6:5 RP1:RP0: Register Bank Select bits (used for direct addressing) 11 = Bank 3 (180h - 1FFh) 10 = Bank 2 (100h - 17Fh) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes. For devices with only Bank0 and Bank1 the IRP bit is reserved, always maintain this bit clear. bit 4 TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit carry/borrow bit (ADDWF, ADDLW, SUBLW, SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0 C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note: For borrow the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A-page 5-7 PICmicro MID-RANGE MCU FAMILY 5.7 OPTION_REG Register The OPTION_REG register is a readable and writable register which contains various control bits to configure the TMR0/WDT prescaler, the external INT Interrupt, TMR0, and the weak pull-ups on PORTB. Register 5-2: OPTION_REG Register R/W-1 RBPU bit 7 R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA bit 7 RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6 INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of INT pin 0 = Interrupt on falling edge of INT pin bit 5 T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4 T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module bit 2-0 PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Note: DS31005A-page 5-8 - n = Value at POR reset To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. 1997 Microchip Technology Inc. Section 5. CPU and ALU 5.8 PCON Register The Power Control (PCON) register contains flag bit(s), that together with the TO and PD bits, allows the user to differentiate between the device resets. Note 1: BOR is unknown on Power-on Reset. It must then be set by the user and checked on subsequent resets to see if BOR is clear, indicating a brown-out has occurred. The BOR status bit is a don't care and is not necessarily predictable if the brown-out circuit is disabled (by clearing the BODEN bit in the Configuration word). Note 2: It is recommended that the POR bit be cleared after a power-on reset has been detected, so that subsequent power-on resets may be detected. Register 5-3: PCON Register R-u MPEEN bit 7 U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 PER R/W-0 POR R/W-0 BOR bit 0 bit 7 MPEEN: Memory Parity Error Circuitry Status bit This bit reflects the value of the MPEEN configuration bit. bit 6:3 Unimplemented: Read as '0' bit 2 PER: Memory Parity Error Reset Status bit 1 = No error occurred 0 = A program memory fetch parity error occurred (must be set in software after a Power-on Reset occurs) bit 1 POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A-page 5-9 PICmicro MID-RANGE MCU FAMILY 5.9 Design Tips Question 1: My program algorithm does not seem to function correctly. Answer 1: 1. 2. The destination of the instruction may be specifying the W register (d = 0) instead of the file register (d = 1). The register bank select bits (RP1:RP0 or IRP) may not be properly selected. Also if interrupts are used, the register bank select bits may not be properly restored when exiting the interrupt handler. Question 2: I cannot seem to modify the STATUS register flags. Answer 2: if the STATUS register is the destination for an instruction that affects the Z, DC, or C bits, the write to these bits is disabled. These bits are set or cleared based on device logic. Therefore, to modify bits in the STATUS register it is recommended to use the BCF and BSF instructions. DS31005A-page 5-10 1997 Microchip Technology Inc. Section 5. CPU and ALU 5.10 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the CPU or the ALU are: Title Application Note # Fixed Point Routines AN617 IEEE 754 Compliant Floating Point Routines AN575 Digital Signal Processing with the PIC16C74 AN616 Math Utility Routines AN544 Implementing IIR Digital Filters AN540 Implementation of Fast Fourier Transforms AN542 Tone Generation AN543 Servo Control of a DC Brushless Motor AN532 Implementation of the Data Encryption Standard using the PIC17C42 AN583 PIC16C5X / PIC16CXX Utility Math Routines AN526 Real Time Operating System for PIC16/17 AN585 5 CPU and ALU 1997 Microchip Technology Inc. DS31005A-page 5-11 PICmicro MID-RANGE MCU FAMILY 5.11 Revision History Revision A This is the initial released revision of the CPU and ALU description. DS31005A-page 5-12 1997 Microchip Technology Inc. Memory Organization M 6 Section 6. Memory Organization HIGHLIGHTS This section of the manual contains the following major topics: 6.1 6.2 6.3 6.4 6.5 6.6 6.7 Introduction ....................................................................................................................6-2 Program Memory Organization......................................................................................6-2 Data Memory Organization ............................................................................................6-8 Initialization ..................................................................................................................6-14 Design Tips ..................................................................................................................6-16 Related Application Notes............................................................................................6-17 Revision History ...........................................................................................................6-18 1997 Microchip Technology Inc. DS31006A page 6-1 PICmicro MID-RANGE MCU FAMILY 6.1 Introduction There are two memory blocks in the Section 6. Memory Organization; program memory and data memory. Each block has its own bus, so that access to each block can occur during the same oscillator cycle. The data memory can further be broken down into General Purpose RAM and the Special Function Registers (SFRs). The operation of the SFRs that control the "core" are described here. The SFRs used to control the peripheral modules are described in the section discussing each individual peripheral module. 6.2 Program Memory Organization Mid-Range MCU devices have a 13-bit program counter capable of addressing an 8K x 14 program memory space. The width of the program memory bus (instruction word) is 14-bits. Since all instructions are a single word, a device with an 8K x 14 program memory has space for 8K of instructions. This makes it much easier to determine if a device has sufficient program memory for a desired application. This program memory space is divided into four pages of 2K words each (0h - 7FFh, 800h FFFh, 1000h - 17FFh, and 1800h - 1FFFh). Figure 6-1 shows the program memory map as well as the 8 level deep hardware stack. Depending on the device, only a portion of this memory may be implemented. Please refer to the device data sheet for the available memory. To jump between the program memory pages, the high bits of the Program Counter (PC) must be modified. This is done by writing the desired value into a SFR called PCLATH (Program Counter Latch High). If sequential instructions are executed, the program counter will cross the page boundaries without any user intervention. For devices that have less than 8K words, accessing a location above the physically implemented address will cause a wraparound. That is, in a 4K-word device accessing 17FFh actually addresses 7FFh. 2K-word devices (or less) do not require paging. DS31006A-page 6-2 1997 Microchip Technology Inc. Section 6. Memory Organization Figure 6-1: 6 Architectural Program Memory Map and Stack Memory Organization PCLATH PC<12:0> PC<12:8> CALL, RETURN RETFIE, RETLW PCL 13 Stack Level 1 Stack Level 8 2K 4K 6K 8K Reset Vector 0000h Interrupt Vector 0004h 0005h On-chip Program Memory (Page 0) On-chip Program Memory (Page 1) On-chip Program Memory (Page 2) On-chip Program Memory (Page 3) 07FFh 0800h 0FFFh 1000h 17FFh 1800h 1FFFh Note 1: Not all devices implement the entire program memory space 2: Calibration Data may be programmed into program memory locations. 1997 Microchip Technology Inc. DS31006A-page 6-3 PICmicro MID-RANGE MCU FAMILY 6.2.1 Reset Vector On any device, a reset forces the Program Counter (PC) to address 0h. We call this address the "Reset Vector Address" since this is the address that program execution will branch to when a device reset occurs. Any reset will also clear the contents of the PCLATH register. This means that any branch at the Reset Vector Address (0h) will jump to that location in PAGE0 of the program memory. 6.2.2 Interrupt Vector When an interrupt is acknowledged the PC is forced to address 0004h. We call this the "Interrupt Vector Address". When the PC is forced to the interrupt vector, the PCLATH register is not modified. Once in the service interrupt routine (ISR), this means that before any write to the PC, the PCLATH register should be written with the value that will specify the desired location in program memory. Before the PCLATH register is modified by the Interrupt Service Routine (ISR) the contents of the PCLATH may need to be saved, so it can be restored before returning from the ISR. 6.2.3 Calibration Information Some devices have calibration information stored in their program memory. This information is programmed by Microchip when the device is under final test. The use of these values allows the application to achieve better results. The calibration information is typically at the end of program memory, and is implemented as a RETLW instruction with the literal value being the specified calibration information. Note: DS31006A-page 6-4 For windowed devices, write down all calibration values BEFORE erasing. This allows the device's calibration values to be restored when the device is re-programmed. When possible writing the values on the package is recommended. 1997 Microchip Technology Inc. Section 6. Memory Organization 6.2.4 6 Program Counter (PC) Figure 6-2 shows the four situations for the loading of the PC. Situation 1 shows how the PC is loaded on a write to PCL (PCLATH<4:0> PCH). Situation 2 shows how the PC is loaded during a GOTO instruction (PCLATH<4:3> PCH). Situation 3 shows how the PC is loaded during a CALL instruction (PCLATH<4:3> PCH), with the PC loaded (PUSHed) onto the Top of Stack. Situation 4 shows how the PC is loaded during one of the return instructions where the PC loaded (POPed) from the Top of Stack. Figure 6-2: Loading of PC In Different Situations Situation 1 - Instruction with PCL as destination PCH Top of STACK PCL 12 8 STACK (13-bits x 8) 7 0 PC 5 8 PCLATH<4:0> ALU result PCLATH STACK (13-bits x 8) Situation 2 - GOTO Instruction PCH 12 11 10 Top of STACK PCL 8 0 7 PC 2 11 PCLATH<4:3> Opcode <10:0> PCLATH Situation 3 - CALL Instruction STACK (13-bits x 8) 13 Top of STACK PCH 12 11 10 PCL 8 7 0 PC 2 11 PCLATH<4:3> Opcode <10:0> PCLATH Situation 4 - RETURN, RETFIE, or RETLW Instruction 13 STACK (13-bits x 8) Top of STACK PCH 12 11 10 PCL 8 0 7 PC 11 Opcode <10:0> PCLATH Note: PCLATH is never updated with the contents of PCH. 1997 Microchip Technology Inc. DS31006A-page 6-5 Memory Organization The program counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13-bits wide. The low byte is called the PCL register. This register is readable and writable. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly readable or writable. All updates to the PCH register go through the PCLATH register. PICmicro MID-RANGE MCU FAMILY 6.2.4.1 Computed GOTO A computed GOTO is accomplished by adding an offset to the program counter (ADDWF PCL). When doing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary (each 256 byte block). Note: 6.2.5 Any write to the Program Counter (PCL), will cause the lower five bits of the PCLATH to be loaded into PCH. Stack The stack allows a combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Mid-Range MCU devices have an 8-level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed. After the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on). An example of the overwriting of the stack is shown in Figure 6-3. Figure 6-3: Stack Modification STACK Push1 Push9 Push2 Push10 Push3 Push4 Push5 Push6 Push7 Push8 Top of STACK Note 1: There are no status bits to indicate stack overflow or stack underflow conditions. Note 2: There are no instructions/mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL, RETURN, RETLW, and RETFIE instructions, or the vectoring to an interrupt address. DS31006A-page 6-6 1997 Microchip Technology Inc. Section 6. Memory Organization 6.2.6 6 Program Memory Paging Note: Devices with program memory sizes 2K words and less, ignore both paging bits (PCLATH<4:3>), which are used to access program memory when more than one page is available. The use of PCLATH<4:3> as general purpose read/write bits (for these devices) is not recommended since this may affect upward compatibility with future products. Devices with program memory sizes between 2K words and 4K words, ignore the paging bit (PCLATH<4>), which is used to access program memory pages 2 and 3 (1000h - 1FFFh). The use of PCLATH<4> as a general purpose read/write bit (for these devices) is not recommended since this may affect upward compatibility with future products. Example 6-1 shows the calling of a subroutine in page 1 of the program memory. This example assumes that PCLATH is saved and restored by the interrupt service routine (if interrupts are used). Example 6-1: Call of a Subroutine in Page1 from Page0 ORG 0x500 BSF PCLATH,3 CALL SUB1_P1 : : ORG 0x900 SUB1_P1: : RETURN 1997 Microchip Technology Inc. ; ; ; ; ; ; ; ; ; Select Page1 (800h-FFFh) Call subroutine in Page1 (800h-FFFh) called subroutine Page1 (800h-FFFh) return to Call subroutine in Page0 (000h-7FFh) DS31006A-page 6-7 Memory Organization Some devices have program memory sizes greater then 2K words, but the CALL and GOTO instructions only have a 11-bit address range. This 11-bit address range allows a branch within a 2K program memory page size. To allow CALL and GOTO instructions to address the entire 1K program memory address range, there must be another two bits to specify the program memory page. These paging bits come from the PCLATH<4:3> bits (Figure 6-2). When doing a CALL or GOTO instruction, the user must ensure that page bits (PCLATH<4:3>) are programmed so that the desired program memory page is addressed (Figure 6-2). When one of the return instructions is executed, the entire 13-bit PC is POPed from the stack. Therefore, manipulation of the PCLATH<4:3> is not required for the return instructions. PICmicro MID-RANGE MCU FAMILY 6.3 Data Memory Organization Data memory is made up of the Special Function Registers (SFR) area, and the General Purpose Registers (GPR) area. The SFRs control the operation of the device, while GPRs are the general area for data storage and scratch pad operations. The data memory is banked for both the GPR and SFR areas. The GPR area is banked to allow greater than 96 bytes of general purpose RAM to be addressed. SFRs are for the registers that control the peripheral and core functions. Banking requires the use of control bits for bank selection. These control bits are located in the STATUS Register (STATUS<7:5>). Figure 6-5 shows one of the data memory map organizations, this organization is device dependent. To move values from one register to another register, the value must pass through the W register. This means that for all register-to-register moves, two instruction cycles are required. The entire data memory can be accessed either directly or indirectly. Direct addressing may require the use of the RP1:RP0 bits. Indirect addressing requires the use of the File Select Register (FSR). Indirect addressing uses the Indirect Register Pointer (IRP) bit of the STATUS register for accesses into the Bank0 / Bank1 or the Bank2 / Bank3 areas of data memory. 6.3.1 General Purpose Registers (GPR) Some Mid-Range MCU devices have banked memory in the GPR area. GPRs are not initialized by a Power-on Reset and are unchanged on all other resets. The register file can be accessed either directly, or using the File Select Register FSR, indirectly. Some devices have areas that are shared across the data memory banks, so a read / write to that area will appear as the same location (value) regardless of the current bank. We refer to this area as the Common RAM. 6.3.2 Special Function Registers (SFR) The SFRs are used by the CPU and Peripheral Modules for controlling the desired operation of the device. These registers are implemented as static RAM. The SFRs can be classified into two sets, those associated with the "core" function and those related to the peripheral functions. Those registers related to the "core" are described in this section, while those related to the operation of the peripheral features are described in the section of that peripheral feature. All Mid-Range MCU devices have banked memory in the SFR area. Switching between these banks requires the RP0 and RP1 bits in the STATUS register to be configured for the desired bank. Some SFRs are initialized by a Power-on Reset and other resets, while other SFRs are unaffected. Note: The Special Function Register (SFR) Area may have General Purpose Registers (GPRs) mapped in these locations. The register file can be accessed either directly, or using the File Select Register FSR, indirectly. DS31006A-page 6-8 1997 Microchip Technology Inc. Section 6. Memory Organization 6.3.3 6 Banking Table 6-1: Direct and Indirect Addressing of Banks Accessed Bank 0 1 2 3 Direct (RP1:RP0) 0 0 1 1 Indirect (IRP) 0 1 0 1 0 1 Each Bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers. All data memory is implemented as static RAM. All Banks may contain special function registers. Some "high use" special function registers from Bank0 are mirrored in the other banks for code reduction and quicker access. Through the evolution of the products, there are a few variations in the layout of the Data Memory. The data memory organization that will be the standard for all new devices is shown in Figure 6-5. This Memory map has the last 16-bytes mapped across all memory banks. This is to reduce the software overhead for context switching. The registers in bold will be in every device. The other registers are peripheral dependent. Not every peripheral's registers are shown, because some file addresses have a different registers from those shown. As with all the figures, tables, and specifications presented in this reference guide, verify the details with the device specific data sheet. Figure 6-4: Direct Addressing Direct Addressing from opcode RP1 RP0 6 bank select location select 0 00 01 10 11 00h Data Memory 7Fh 7Fh Bank0 1997 Microchip Technology Inc. Bank1 Bank2 Bank3 DS31006A-page 6-9 Memory Organization The data memory is partitioned into four banks. Each bank contains General Purpose Registers and Special Function Registers. Switching between these banks requires the RP0 and RP1 bits in the STATUS register to be configured for the desired bank when using direct addressing. The IRP bit in the STATUS register is used for indirect addressing. PICmicro MID-RANGE MCU FAMILY Figure 6-5: Register File Map INDF TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTD PORTE PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES ADCON0 File Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h INDF OPTION_REG PCL STATUS FSR TRISA TRISB TRISC TRISD TRISE PCLATH INTCON PIE1 PIE2 PCON OSCCAL PR2 SSPADD SSPATAT TXSTA SPBRG ADCON1 File Address 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h INDF TMR0 PCL STATUS FSR PORTB PORTF PORTG PCLATH INTCON File Address 100h 101h 102h 103h 104h 105h 106h 107h 108h 109h 10Ah 10Bh 10Ch 10Dh 10Eh 10Fh 110h 111h 112h 113h 114h 115h 116h 117h 118h 119h 11Ah 11Bh 11Ch 11Dh 11Eh 11Fh 120h INDF OPTION_REG PCL STATUS FSR TRISB TRISF TRISG PCLATH INTCON File Address 180h 181h 182h 183h 184h 185h 186h 187h 188h 189h 18Ah 18Bh 18Ch 18Dh 18Eh 18Fh 190h 191h 192h 193h 194h 195h 196h 197h 198h 199h 19Ah 19Bh 19Ch 19Dh 19Eh 19Fh 1A0h General General General Purpose Purpose Purpose Registers (3) EFh Registers (3) 16Fh Registers (3) 1EFh F0h Mapped in 170h Mapped in 1F0h Mapped in Bank0 Bank0 Bank0 FFh 70h - 7Fh (4) 17Fh 70h - 7Fh (4) 1FFh 7Fh 70h - 7Fh (4) (5) Bank0 Bank1 Bank2 Bank3 (5) Registers in BOLD will be present in every device. Not all locations may be implemented. Unimplemented locations will read as '0'. These locations may not be implemented. Depending on the device, accesses to the unimplemented locations operate differently. Please refer to the specific device data sheet for details. Some device do not map these registers into Bank0. In devices where these registers are mapped into Bank0, these registers are referred to as common RAM Some devices may not implement these banks. Locations in unimplemented banks will read as '0'. General Purpose Registers (GPRs) may be located in the Special Function Register (SFR) area. General Purpose Registers (2) Note 1: 2: 3: 4: 5: 6: DS31006A-page 6-10 1997 Microchip Technology Inc. Section 6. Memory Organization The map in Figure 6-6 shows the register file memory map of some 18-pin devices. Unimplemented registers will read as '0'. Memory Organization Figure 6-6: Register File Map INDF TMR0 PCL STATUS FSR PORTA PORTB ADCON0 / EEDATA (2) ADRES / EEADR (2) PCLATH INTCON General Purpose Registers (3) Bank0 File File Address Address 00h INDF 80h 01h OPTION_REG 81h 02h PCL 82h 03h STATUS 83h 04h FSR 84h 05h TRISA 85h 06h TRISB 86h 07h PCON 87h 08h ADCON1 / 88h EECON1 (2) 09h ADRES / 89h EECON2 (2) 0Ah PCLATH 8Ah 0Bh INTCON 8Bh 0Ch 8Ch General Purpose Registers (4) 7Fh FFh Bank1 Note 1: Registers in BOLD will be present in every device. 2: These registers may not be implemented, or are implemented as other registers in some devices. 3: Not all locations may be implemented. Unimplemented locations will read as '0'. 4: These locations are unimplemented in Bank1. Access to these unimplemented locations will access the corresponding Bank0 register. 1997 Microchip Technology Inc. 6 DS31006A-page 6-11 PICmicro MID-RANGE MCU FAMILY 6.3.4 Indirect Addressing, INDF, and FSR Registers Indirect addressing is a mode of addressing data memory where the data memory address in the instruction is not fixed. An SFR register is used as a pointer to the data memory location that is to be read or written. Since this pointer is in RAM, the contents can be modified by the program. This can be useful for data tables in the data memory. Figure 6-7 shows the operation of indirect addressing. This shows the moving of the value to the data memory address specified by the value of the FSR register. Indirect addressing is possible by using the INDF register. Any instruction using the INDF register actually accesses the register pointed to by the File Select Register, FSR. Reading the INDF register itself indirectly (FSR = '0') will read 00h. Writing to the INDF register indirectly results in a no-operation (although status bits may be affected). An effective 9-bit address is generated by the concatenation of the IRP bit (STATUS<7>) with the 8-bit FSR register, as shown in Figure 6-8. Figure 6-7: Indirect Addressing RAM Instruction Executed Opcode Address 9 File Address = INDF Address = 0h Address != 0 RP1:RP0 Instruction Fetched Opcode DS31006A-page 6-12 2 9 9 7 File IRP FSR 1997 Microchip Technology Inc. Section 6. Memory Organization 6 Figure 6-8: Indirect Addressing IRP 7 FSR register bank select 00 01 10 0 location select 11 00h 00h Data Memory 7Fh 7Fh Bank0 Bank1 Bank2 Bank3 Example 6-2 shows a simple use of indirect addressing to clear RAM (locations 20h-2Fh) in a minimum number of instructions. A similar concept could be used to move a defined number of bytes (block) of data to the USART transmit register (TXREG). The starting address of the block of data to be transmitted could easily be modified by the program. Example 6-2: Indirect Addressing NEXT BCF MOVLW MOVWF CLRF INCF BTFSS GOTO CONTINUE : 1997 Microchip Technology Inc. STATUS, IRP 0x20 FSR INDF FSR,F FSR,4 NEXT ; ; ; ; ; ; ; ; ; Indirect addressing Bank0/1 Initialize pointer to RAM Clear INDF register Inc pointer All done? NO, clear next YES, continue DS31006A-page 6-13 Memory Organization Indirect Addressing PICmicro MID-RANGE MCU FAMILY 6.4 Initialization Example 6-3 shows how the bank switching occurs for Direct addressing, while Example 6-4 shows some code to do initialization (clearing) of General Purpose RAM. Example 6-3: Bank Switching CLRF : BSF : BCF : MOVLW XORWF : BCF : BCF DS31006A-page 6-14 STATUS STATUS, RP0 STATUS, RP0 0x60 STATUS, F STATUS, RP0 STATUS, RP1 ; ; ; ; ; ; ; ; ; ; ; ; Clear STATUS register (Bank0) Bank1 Bank0 Set RP0 and RP1 in STATUS register, other bits unchanged (Bank3) Bank2 Bank0 1997 Microchip Technology Inc. Section 6. Memory Organization 6 Example 6-4: RAM Initialization 1997 Microchip Technology Inc. DS31006A-page 6-15 Memory Organization CLRF STATUS ; Clear STATUS register (Bank0) MOVLW 0x20 ; 1st address (in bank) of GPR area MOVWF FSR ; Move it to Indirect address register Bank0_LP CLRF INDF0 ; Clear GPR at address pointed to by FSR INCF FSR ; Next GPR (RAM) address BTFSS FSR, 7 ; End of current bank ? (FSR = 80h, C = 0) GOTO Bank0_LP ; NO, clear next location ; ; Next Bank (Bank1) ; (** ONLY REQUIRED IF DEVICE HAS A BANK1 **) ; MOVLW 0xA0 ; 1st address (in bank) of GPR area MOVWF FSR ; Move it to Indirect address register Bank1_LP CLRF INDF0 ; Clear GPR at address pointed to by FSR INCF FSR ; Next GPR (RAM) address BTFSS STATUS, C ; End of current bank? (FSR = 00h, C = 1) GOTO Bank1_LP ; NO, clear next location ; ; Next Bank (Bank2) ; (** ONLY REQUIRED IF DEVICE HAS A BANK2 **) ; BSF STATUS, IRP ; Select Bank2 and Bank3 ; for Indirect addressing MOVLW 0x20 ; 1st address (in bank) of GPR area MOVWF FSR ; Move it to Indirect address register Bank2_LP CLRF INDF0 ; Clear GPR at address pointed to by FSR INCF FSR ; Next GPR (RAM) address BTFSS FSR, 7 ; End of current bank? (FSR = 80h, C = 0) GOTO Bank2_LP ; NO, clear next location ; ; Next Bank (Bank3) ; (** ONLY REQUIRED IF DEVICE HAS A BANK3 **) ; MOVLW 0xA0 ; 1st address (in bank) of GPR area MOVWF FSR ; Move it to Indirect address register Bank3_LP CLRF INDF0 ; Clear GPR at address pointed to by FSR INCF FSR ; Next GPR (RAM) address BTFSS STATUS, C ; End of current bank? (FSR = 00h, C = 1) GOTO Bank3_LP ; NO, clear next location : ; YES, All GPRs (RAM) is cleared PICmicro MID-RANGE MCU FAMILY 6.5 Design Tips Question 1: Program execution seems to get lost. Answer 1: When a device with more then 2K words of program memory is used, the calling of subroutines may require that the PCLATH register be loaded prior to the CALL (or GOTO) instruction to specify the correct program memory page that the routine is located on. The following instructions will correctly load PCLATH register, regardless of the program memory location of the label SUB_1. SUB_1 Question 2: MOVLW MOVWF CALL : : : : RETURN HIGH (SUB_1) PCLATH SUB_1 ; Select Program Memory Page of ; Routine. ; Call the desired routine ; Start of routine ; Return from routine I need to initialize RAM to '0's. What is an easy way to do that? Answer 2: Example 6-4 shows this. If the device you are using does not use all 4 data memory banks, some of the code may be removed. DS31006A-page 6-16 1997 Microchip Technology Inc. Section 6. Memory Organization 6.6 6 Related Application Notes Title Implementing a Table Read 1997 Microchip Technology Inc. Application Note # AN556 DS31006A-page 6-17 Memory Organization This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to memory are: PICmicro MID-RANGE MCU FAMILY 6.7 Revision History Revision A This is the initial released revision of the Memory Organization description. DS31006A-page 6-18 1997 Microchip Technology Inc. M Section 7. Data EEPROM HIGHLIGHTS This section of the manual contains the following major topics: Introduction ....................................................................................................................7-2 Control Register .............................................................................................................7-3 EEADR...........................................................................................................................7-4 EECON1 and EECON2 Registers .................................................................................7-4 Reading the EEPROM Data Memory ............................................................................7-5 Writing to the EEPROM Data Memory...........................................................................7-5 Write Verify.....................................................................................................................7-6 Protection Against Spurious Writes ...............................................................................7-7 Data EEPROM Operation During Code Protected Configuration ..................................7-7 Initialization ....................................................................................................................7-7 Design Tips ....................................................................................................................7-8 Related Application Notes..............................................................................................7-9 Revision History ...........................................................................................................7-10 1997 Microchip Technology Inc. DS31007A page 7-1 Data EEPROM 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7 PICmicro MID-RANGE MCU FAMILY 7.1 Introduction The EEPROM data memory is readable and writable during normal operation (full VDD range). This memory is not directly mapped in the register file space. Instead it is indirectly addressed through the Special Function Registers. There are four SFRs used to read and write this memory. These registers are: * * * * EECON1 EECON2 (not a physically implemented register) EEDATA EEADR EEDATA holds the 8-bit data for read/write, and EEADR holds the address of the EEPROM location being accessed. The 8-bit EEADR register can access up to 256 locations of Data EEPROM. The EEADR register can be thought of as the indirect addressing register of the Data EEPROM. EECON1 contains the control bits, while EECON2 is the register used to initiate the read/write. Some devices will implement less then the entire memory map. The address range always starts at 0h, and goes throughout the memory available. Table 7-1 shows some of the possible common device memory sizes and the address range for those sizes. Table 7-1: Possible Data EEPROM Memory Sizes Data EEPROM Size (1) Address Range 64 0h - 3Fh 128 0h - 7Fh 256 0h - FFh Note 1: Presently, devices are only offered with 64 bytes of Data EEPROM. The EEPROM data memory allows byte read and write. A byte write automatically erases the location and writes the new data (erase before write). The EEPROM data memory is rated for high erase/write cycles. The write time is controlled by an on-chip timer. The write-time will vary with voltage and temperature as well as from chip to chip. Please refer to the AC specifications for exact limits. When the device is code protected, the CPU may continue to read and write the data EEPROM memory. The device programmer can no longer access this memory. DS31007A-page 7-2 1997 Microchip Technology Inc. Section 7. Data EEPROM 7.2 Control Register Register 7-1: EECON1 Register U-0 -- bit 7 U-0 -- U-0 -- R/W-1 EEIF (1) R/W-1 WRERR R/W-x WREN R/S-0 WR bit 7:5 Unimplemented: Read as '0' bit 4 EEIF: EEPROM Write Operation Interrupt Flag bit 1 = The write operation completed (must be cleared in software) 0 = The write operation is not complete or has not been started bit 3 WRERR: EEPROM Error Flag bit 1 = A write operation is prematurely terminated (any MCLR reset or any WDT reset during normal operation) 0 = The write operation completed bit 2 WREN: EEPROM Write Enable bit 1 = Allows write cycles 0 = Inhibits write to the data EEPROM bit 1 WR: Write Control bit 1 = initiates a write cycle. The bit is cleared by hardware once write is complete. The WR bit can only be set (not cleared) in software. 0 = Write cycle to the data EEPROM is complete bit 0 RD: Read Control bit 1 = Initiates an EEPROM read. Read takes one cycle. RD is cleared in hardware. The RD bit can only be set (not cleared) in software. 0 = Does not initiate an EEPROM read R/S-x RD bit 0 7 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' S = Settable bit - n = Value at POR reset Note 1: Future devices will have this bit in the PIR register. 1997 Microchip Technology Inc. DS31007A-page 7-3 Data EEPROM Legend PICmicro MID-RANGE MCU FAMILY 7.3 EEADR The EEADR register can address up to a maximum of 256 bytes of data EEPROM. The unused address bits are decoded. This means that these bits must always be '0' to ensure that the address is in the Data EEPROM memory space. 7.4 EECON1 and EECON2 Registers EECON1 is the control register with five low order bits physically implemented. The upper-three bits are unimplemented and read as '0's. Control bits RD and WR initiate read and write, respectively. These bits cannot be cleared, only set, in software. They are cleared in hardware at completion of the read or write operation. The inability to clear the WR bit in software prevents the accidental, premature termination of a write operation. The WREN bit, when set, will allow a write operation. On power-up, the WREN bit is clear. The WRERR bit is set when a write operation is interrupted by a MCLR reset or a WDT time-out reset during normal operation. In these situations, following reset, the user can check the WRERR bit and rewrite the location. The data and address will be unchanged in the EEDATA and EEADR registers. Interrupt flag bit EEIF is set when write is complete. It must be cleared in software. EECON2 is not a physical register. Reading EECON2 will read all '0's. The EECON2 register is used exclusively in the Data EEPROM write sequence. DS31007A-page 7-4 1997 Microchip Technology Inc. Section 7. Data EEPROM 7.5 Reading the EEPROM Data Memory To read a data memory location, the user must write the address to the EEADR register and then set control bit RD (EECON1<0>). The data is available, in the very next instruction cycle, in the EEDATA register; therefore it can be read by the next instruction. EEDATA will hold this value until another read or until it is written to by the user (during a write operation). Example 7-1: Data EEPROM Read BCF MOVLW MOVWF BSF BSF BCF MOVF ; ; ; ; ; ; ; Bank0 Any location in Data EEPROM memory space Address to read Bank1 EE Read Bank0 W = EEDATA Writing to the EEPROM Data Memory To write an EEPROM data location, the user must first write the address to the EEADR register and the data to the EEDATA register. Then the user must follow a specific sequence to initiate the write for each byte. Example 7-2: Data EEPROM Write Required Sequence BSF BCF BSF MOVLW MOVWF MOVLW MOVWF BSF BSF STATUS, RP0 INTCON, GIE EECON1, WREN 55h EECON2 AAh EECON2 EECON1,WR INTCON, GIE ; ; ; ; ; ; ; ; ; Bank1 Disable INTs. Enable Write 55h must be written to EECON2 to start write sequence Write AAh Set WR bit begin write Enable INTs. The write will not initiate if the above sequence is not exactly followed (write 55h to EECON2, write AAh to EECON2, then set WR bit) for each byte. We strongly recommend that interrupts be disabled during this code segment. Additionally, the WREN bit in EECON1 must be set to enable write. This mechanism prevents accidental writes to data EEPROM due to errant (unexpected) code execution (i.e., lost programs). The user should keep the WREN bit clear at all times, except when updating EEPROM. The WREN bit is not cleared by hardware After a write sequence has been initiated, clearing the WREN bit will not affect this write cycle. The WR bit will be inhibited from being set unless the WREN bit is set. At the completion of the write cycle, the WR bit is cleared in hardware and the EE Write Complete Interrupt Flag bit (EEIF) is set. The user can either enable this interrupt or poll this bit. EEIF must be cleared by software. 1997 Microchip Technology Inc. DS31007A-page 7-5 7 Data EEPROM 7.6 STATUS, RP0 CONFIG_ADDR EEADR STATUS, RP0 EECON1, RD STATUS, RP0 EEDATA, W PICmicro MID-RANGE MCU FAMILY 7.7 Write Verify Depending on the application, good programming practice may dictate that the value written to the Data EEPROM be verified (Example 7-3) as the value that was intended to be written. This should be used in applications where an EEPROM bit will be stressed near the specification limit. The Total Endurance disk will help determine your comfort level. Example 7-3: Write Verify BCF : : MOVF BSF STATUS, RP0 ; ; ; EEDATA, W ; STATUS, RP0 ; Bank0 Any code can go here BSF BCF EECON1, RD ; YES, Read the value written STATUS, RP0 ; Bank0 Must be in Bank0 Bank1 READ ; ; Is the value written (in W reg) and read (in EEDATA) the same? ; SUBWF EEDATA, W ; BTFSS STATUS, Z ; Is difference 0? GOTO WRITE_ERR ; NO, Write error : ; YES, Good write : ; Continue program DS31007A-page 7-6 1997 Microchip Technology Inc. Section 7. Data EEPROM 7.8 Protection Against Spurious Writes There are conditions when the device may not want to write to the data EEPROM memory. To protect against spurious EEPROM writes, various mechanisms have been built-in. On power-up, WREN is cleared. Also, the Power-up Timer (72 ms duration) prevents EEPROM write. The write initiate sequence and the WREN bit together help prevent an accidental write during brown-outs, power glitches, and software malfunction. 7.9 Data EEPROM Operation During Code Protected Configuration When the device is code protected, the CPU is able to read and write data to the Data EEPROM. For ROM devices, there are two code protection bits. One for the ROM program memory and one for the Data EEPROM memory. See the Device Programming Specification for more information about these bits. 7.10 7 Initialization As for the General Purpose RAM, it is a good idea to initialize all Data EEPROM locations to a known state. This initialization may take place at the time of device programming or an application diagnostic mode, since on reset you may not want the Data EEPROM to be cleared. An Application Diagnostic mode may be a condition on the I/O pins that the device tests for after the device power-ups. Then depending on this mode, the device would do some diagnostic function. The state for the I/O pins would need to be something that would not be possible without the injected levels to force this diagnostic mode. 1997 Microchip Technology Inc. DS31007A-page 7-7 Data EEPROM The Data EEPROM module does not have an initialization sequence such as other modules. To do a read of the Data EEPROM refer to Example 7-1. To do a write to the Data EEPROM refer to Example 7-2, and to verify that the write completed successfully refer to Example 7-3. PICmicro MID-RANGE MCU FAMILY 7.11 Design Tips Question 1: Why do the data EEPROM locations not contain the data that I wrote? Answer 1: There are a few possibilities, but the most likely is that you did not exactly follow the write sequence as shown in Example 7-2. If you are using this code segment ensure that all interrupts are disabled during this sequence. Question 2: Why is the data in the data EEPROM is getting corrupted? Answer 2: The data will only change when a Data EEPROM write occurs. Inadvertent writes may occur when the device is in a brown-out condition (out of operating specification) and the device is not being forced to the reset state. During a brown-out, either the internal brown-out circuitry should be enabled (when available) or external circuitry should be used to reset the PICmicro MCU to ensure that no data EEPROM writes occur when the device is out of the valid operating range. DS31007A-page 7-8 1997 Microchip Technology Inc. Section 7. Data EEPROM 7.12 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to data EEPROM are: Title Application Note # AN601 How to get 10 Million Cycles out of your Microchip Serial EEPROM AN602 Basic Serial EEPROM Operation AN536 Everything a System Engineer needs to know about Serial EEPROM Endurance AN537 Using the Microchip Endurance Predictive Software AN562 1997 Microchip Technology Inc. DS31007A-page 7-9 7 Data EEPROM EEPROM Endurance Tutorial PICmicro MID-RANGE MCU FAMILY 7.13 Revision History Revision A This is the initial released revision of the Data EEPROM description. DS31007A-page 7-10 1997 Microchip Technology Inc. M Section 8. Interrupts HIGHLIGHTS This section of the manual contains the following major topics: 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8 8.9 Introduction ....................................................................................................................8-2 Control Registers ...........................................................................................................8-5 Interrupt Latency ..........................................................................................................8-10 INT and External Interrupts..........................................................................................8-10 Context Saving During Interrupts .................................................................................8-11 Initialization ..................................................................................................................8-14 Design Tips ..................................................................................................................8-16 Related Application Notes............................................................................................8-17 Revision History ...........................................................................................................8-18 8 Interrupts 1997 Microchip Technology Inc. DS31008A page 8-1 PICmicro MID-RANGE MCU FAMILY 8.1 Introduction PICmicro MCUs can have many sources of interrupt. These sources generally include one interrupt source for each peripheral module, though some modules may generate multiple interrupts (such as the USART module). The current interrupts are: * * * * * * * * * * * * * * * INT Pin Interrupt (external interrupt) TMR0 Overflow Interrupt PORTB Change Interrupt (pins RB7:RB4) Comparator Change Interrupt Parallel Slave Port Interrupt USART Interrupts Receive Interrupt Transmit Interrupt A/D Conversion Complete Interrupt LCD Interrupt. Data EEPROM Write Complete Interrupt Timer1 Overflow Interrupt Timer2 Overflow Interrupt CCP Interrupt SSP Interrupt There is a minimum of one register used in the control and status of the interrupts. This register is: * INTCON Additionally, if the device has peripheral interrupts, then it will have registers to enable the peripheral interrupts and registers to hold the interrupt flag bits. Depending on the device, the registers are: * * * * PIE1 PIR1 PIE2 PIR2 We will generically refer to these registers as PIR and PIE. If future devices provide more interrupt sources, they will be supported by additional register pairs, such as PIR3 and PIE3. The Interrupt Control Register, INTCON, records individual flag bits for core interrupt requests. It also has various individual enable bits and the global interrupt enable bit. DS31008A-page 8-2 1997 Microchip Technology Inc. Section 8. Interrupts The Global Interrupt Enable bit, GIE (INTCON<7>), enables (if set) all un-masked interrupts or disables (if cleared) all interrupts. Individual interrupts can be disabled through their corresponding enable bits in the INTCON register. The GIE bit is cleared on reset. The "return from interrupt" instruction, RETFIE, exits the interrupt routine as well as sets the GIE bit, which allows any pending interrupt to execute. The INTCON register contains these interrupts: INT Pin Interrupt, the RB Port Change Interrupt, and the TMR0 Overflow Interrupt. The INTCON register also contains the Peripheral Interrupt Enable bit, PEIE. The PEIE bit will enable/disable the peripheral interrupts from vectoring when the PEIE bit is set/cleared. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed into the stack and the PC is loaded with 0004h. Once in the interrupt service routine the source(s) of the interrupt can be determined by polling the interrupt flag bits. Generally the interrupt flag bit(s) must be cleared in software before re-enabling the global interrupt to avoid recursive interrupts. Once in the interrupt service routine the source(s) of the interrupt can be determined by polling the interrupt flag bits. Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. Note 1: Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. Note 2: When an instruction that clears the GIE bit is executed, any interrupts that were pending for execution in the next cycle are ignored. The CPU will execute a NOP in the cycle immediately following the instruction which clears the GIE bit. The interrupts which were ignored are still pending to be serviced when the GIE bit is set again. 8 Interrupts 1997 Microchip Technology Inc. DS31008A-page 8-3 PICmicro MID-RANGE MCU FAMILY Figure 8-1: Interrupt Logic PIR/PIE Registers INTCON Register ADCIF ADCIE ADIF ADIE CCP1IF CCP1IE CCP2IF CCP2IE CMIF CMIE EEIF EEIE GPIF GPIE INTF INTE RBIF RBIE T0IF T0IE LCDIF LCDIE OVFIF OVFIE Wake-up (If in SLEEP mode) Interrupt to CPU Clear GIE bit PEIE (EEIE 2) (ADIE 2) PBIF PBIE GIE PSPIF PSPIE RCIF RCIE SSPIF SSPIE TMR1IF TMR1IE TMR2IF TMR2IE TXIF TXIE DS31008A-page 8-4 Note 1: This shows all current Interrupt bits (at time of manual printing) for all PICmicro Mid-Range MCUs. Which bits pertain to a specific device is dependent upon the device type and peripherals implemented. See specific device data sheet. 2: Some of the original Mid-Range devices had only one peripheral module. These devices do not have the PEIE bit, and have the module enable bit in the INTCON register. 1997 Microchip Technology Inc. Section 8. Interrupts 8.2 Control Registers Generally devices have a minimum of three registers associated with interrupts. The INTCON register which contains Global Interrupt Enable bit, GIE, as well as the Peripheral Interrupt Enable bit, PEIE, and the PIE / PIR register pair which enable the peripheral interrupts and display the interrupt flag status. 8.2.1 INTCON Register The INTCON Register is a readable and writable register which contains various enable and flag bits. Note: Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>).This feature allows for software polling. Register 8-1: INTCON Register R/W-0 GIE R/W-0 PEIE (3) R/W-0 T0IE R/W-0 INTE (2) R/W-0 RBIE (1, R/W-0 T0IF R/W-0 INTF (2) R/W-0 RBIF (1, 2) 2) bit 7 bit 0 bit 7 GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts bit 6 PEIE: Peripheral Interrupt Enable bit 1 = Enables all un-masked peripheral interrupts 0 = Disables all peripheral interrupts bit 5 T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 overflow interrupt 0 = Disables the TMR0 overflow interrupt bit 4 INTE: INT External Interrupt Enable bit 1 = Enables the INT external interrupt 0 = Disables the INT external interrupt bit 3 RBIE (1): RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2 T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1 INTF: INT External Interrupt Flag bit 1 = The INT external interrupt occurred (must be cleared in software) 0 = The INT external interrupt did not occur bit 0 RBIF (1): RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state 8 Interrupts Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: In some devices, the RBIE bit may also be known as GPIE and the RBIF bit may be know as GPIF. Note 2: Some devices may not have this feature. For those devices this bit is reserved. Note 3: In devices with only one peripheral interrupt, this bit may be EEIE or ADIE. 1997 Microchip Technology Inc. DS31008A-page 8-5 PICmicro MID-RANGE MCU FAMILY 8.2.2 PIE Register(s) Depending on the number of peripheral interrupt sources, there may be multiple Peripheral Interrupt Enable registers (PIE1, PIE2). These registers contain the individual enable bits for the Peripheral interrupts. These registers will be generically referred to as PIE. If the device has a PIE register, The PEIE bit must be set to enable any of these peripheral interrupts. Note: Bit PEIE (INTCON<6>) must be set to enable any of the peripheral interrupts. Although, the PIE register bits have a general bit location with each register, future devices may not have consistent placement. Bit location inconsistencies will not be a problem if you use the supplied Microchip Include files for the symbolic use of these bits. This will allow the Assembler/Compiler to automatically take care of the placement of these bits by specifying the correct register and bit name. DS31008A-page 8-6 1997 Microchip Technology Inc. Section 8. Interrupts Register 8-2: PIE Register R/W-0 (Note 1) bit 7 bit 0 bit TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt bit TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit CCP2IE: CCP2 Interrupt Enable bit 1 = Enables the CCP2 interrupt 0 = Disables the CCP2 interrupt bit SSPIE: Synchronous Serial Port Interrupt Enable bit 1 = Enables the SSP interrupt 0 = Disables the SSP interrupt bit RCIE: USART Receive Interrupt Enable bit 1 = Enables the USART receive interrupt 0 = Disables the USART receive interrupt bit TXIE: USART Transmit Interrupt Enable bit 1 = Enables the USART transmit interrupt 0 = Disables the USART transmit interrupt bit ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt bit ADCIE: Slope A/D Converter comparator Trip Interrupt Enable bit 1 = Enables the Slope A/D interrupt 0 = Disables the Slope A/D interrupt bit OVFIE: Slope A/D TMR Overflow Interrupt Enable bit 1 = Enables the Slope A/D TMR overflow interrupt 0 = Disables the Slope A/D TMR overflow interrupt bit PSPIE: Parallel Slave Port Read/Write Interrupt Enable bit 1 = Enables the PSP read/write interrupt 0 = Disables the PSP read/write interrupt bit EEIE: EE Write Complete Interrupt Enable bit 1 = Enables the EE write complete interrupt 0 = Disables the EE write complete interrupt bit LCDIE: LCD Interrupt Enable bit 1 = Enables the LCD interrupt 0 = Disables the LCD interrupt bit CMIE: Comparator Interrupt Enable bit 1 = Enables the Comparator interrupt 0 = Disables the Comparator interrupt 8 Interrupts Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: The bit position of the enable bits is device dependent. Please refer to the device data sheet for bit placement. 1997 Microchip Technology Inc. DS31008A-page 8-7 PICmicro MID-RANGE MCU FAMILY 8.2.3 PIR Register(s) Depending on the number of peripheral interrupt sources, there may be multiple Peripheral Interrupt Flag registers (PIR1, PIR2). These registers contain the individual flag bits for the peripheral interrupts. These registers will be generically referred to as PIR. Note 1: Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). Note 2: User software should ensure the appropriate interrupt flag bits are cleared (by software) prior to enabling an interrupt, and after servicing that interrupt. Although, the PIR bits have a general bit location within each register, future devices may not be able to be consistent with that. It is recommended that you use the supplied Microchip Include files for the symbolic use of these bits. This will allow the Assembler/Compiler to automatically take care of the placement of these bits within the specified register. Register 8-3: PIR Register R/W-0 (Note 1) bit 7 bit bit bit bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred CCP1IF: CCP1 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred bit PWM Mode Unused in this mode CCP2IF: CCP2 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred bit bit bit bit DS31008A-page 8-8 PWM Mode Unused in this mode SSPIF: Synchronous Serial Port Interrupt Flag bit 1 = The transmission/reception is complete 0 = Waiting to transmit/receive RCIF: USART Receive Interrupt Flag bit 1 = The USART receive buffer, RCREG, is full (cleared when RCREG is read) 0 = The USART receive buffer is empty TXIF: USART Transmit Interrupt Flag bit 1 = The USART transmit buffer, TXREG, is empty (cleared when TXREG is written) 0 = The USART transmit buffer is full ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete 1997 Microchip Technology Inc. Section 8. Interrupts Register 8-3: bit bit bit bit bit bit PIR Register (Cont'd) ADCIF: Slope A/D Converter Comparator Trip Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete OVFIF: Slope A/D TMR Overflow Interrupt Flag bit 1 = Slope A/D TMR overflowed (must be cleared in software) 0 = Slope A/D TMR did not overflow PSPIF: Parallel Slave Port Read/Write Interrupt Flag bit 1 = A read or a write operation has taken place (must be cleared in software) 0 = No read or write has occurred EEIF: EE Write Complete Interrupt Flag bit 1 = The data EEPROM write operation is complete (must be cleared in software) 0 = The data EEPROM write operation is not complete LCDIF: LCD Interrupt Flag bit 1 = LCD interrupt has occurred (must be cleared in software) 0 = LCD interrupt has not occurred CMIF: Comparator Interrupt Flag bit 1 = Comparator input has changed (must be cleared in software) 0 = Comparator input has not changed Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 8 - n = Value at POR reset 1997 Microchip Technology Inc. DS31008A-page 8-9 Interrupts Note 1: The bit position of the flag bits is device dependent. Please refer to the device data sheet for bit placement. PICmicro MID-RANGE MCU FAMILY 8.3 Interrupt Latency Interrupt latency is defined as the time from the interrupt event (the interrupt flag bit gets set) to the time that the instruction at address 0004h starts execution (when that interrupt is enabled). For synchronous interrupts (typically internal), the latency is 3TCY. For asynchronous interrupts (typically external), such as the INT or Port RB Change Interrupt, the interrupt latency will be 3 - 3.75TCY (instruction cycles). The exact latency depends upon when the interrupt event occurs (Figure 8-2) in relation to the instruction cycle. The latency is the same for both one and two cycle instructions. 8.4 INT and External Interrupts The external interrupt on the INT pin is edge triggered: either rising if the INTEDG bit (OPTION<6>) is set, or falling, if the INTEDG bit is clear. When a valid edge appears on the INT pin, the INTF flag bit (INTCON<1>) is set. This interrupt can be enabled/disabled by setting/clearing the INTE enable bit (INTCON<4>). The INTF bit must be cleared in software in the interrupt service routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if the INTE bit was set prior to going into SLEEP. The status of the GIE bit decides whether or not the processor branches to the interrupt vector following wake-up. See the "Watchdog Timer and Sleep Mode" section for details on SLEEP and for timing of wake-up from SLEEP through INT interrupt. Figure 8-2: INT Pin and Other External Interrupt Timing Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT 3 4 INT pin 1 1 INTF flag (INTCON<1>) Interrupt Latency 2 5 GIE bit (INTCON<7>) INSTRUCTION FLOW PC PC Instruction fetched Inst (PC) Instruction executed Inst (PC-1) PC+1 Inst (PC+1) Inst (PC) PC+1 -- Dummy Cycle 0004h 0005h Inst (0004h) Inst (0005h) Dummy Cycle Inst (0004h) Note 1: INTF flag is sampled here (every Q1). 2: Interrupt latency = 3-4 TCY where TCY = instruction cycle time. Latency is the same whether Instruction (PC) is a single cycle or a 2-cycle instruction. 3: CLKOUT is available only in RC oscillator mode. 4: For minimum width of INT pulse, refer to AC specs. 5: INTF is enabled to be set anytime during the Q4-Q1 cycles. Note: DS31008A-page 8-10 Any interrupts caused by external signals (such as timers, capture, change on port) will have similar timing. 1997 Microchip Technology Inc. Section 8. Interrupts 8.5 Context Saving During Interrupts During an interrupt, only the return PC value is saved on the stack. Typically, users may wish to save key registers during an interrupt e.g. W register and STATUS register. This has to be implemented in software. The action of saving information is commonly referred to as "PUSHing," while the action of restoring the information before the return is commonly referred to as "POPing." These (PUSH, POP) are not instruction mnemonics, but are conceptual actions. This action can be implemented by a sequence of instructions. For ease of code transportability, these code segments can be made into MACROs (see MPASM Assembler User's Guide for details on creating macros). Example 8-1 stores and restores the STATUS and W registers for devices with common RAM (such as the PIC16C77). The user register, W_TEMP, must be defined across all banks and must be defined at the same offset from the bank base address (i.e., W_TEMP is defined at 0x70 0x7F in Bank0). The user register, STATUS_TEMP, must be defined in Bank0, in this example STATUS_TEMP is also in Bank0. The steps of Example 8-1: 1. 2. 3. 4. 5. Stores the W register regardless of current bank. Stores the STATUS register in Bank0. Executes the Interrupt Service Routine (ISR) code. Restores the STATUS (and bank select bit register). Restores the W register. If additional locations need to be saved before executing the Interrupt Service Routine (ISR) code, they should be saved after the STATUS register is saved (step 2), and restored before the STATUS register is restored (step 4). MOVWF W_TEMP SWAPF STATUS,W MOVWF STATUS_TEMP ; Copy W to a Temporary Register ; regardless of current bank ; Swap STATUS nibbles and place ; into W register ; Save STATUS to a Temporary register ; in Bank0 : : (Interrupt Service Routine (ISR) ) : SWAPF STATUS_TEMP,W ; Swap original STATUS register value ; into W (restores original bank) MOVWF STATUS ; Restore STATUS register from ; W register SWAPF W_TEMP,F ; Swap W_Temp nibbles and return ; value to W_Temp SWAPF W_TEMP,W ; Swap W_Temp to W to restore original ; W value without affecting STATUS 1997 Microchip Technology Inc. DS31008A-page 8-11 Interrupts Example 8-1: Saving the STATUS and W Registers in RAM (for Devices with Common RAM) 8 PICmicro MID-RANGE MCU FAMILY Example 8-2 stores and restores the STATUS and W registers for devices without common RAM (such as the PIC16C74A). The user register, W_TEMP, must be defined across all banks and must be defined at the same offset from the bank base address (i.e., W_TEMP is defined at 0x70 - 0x7F in Bank0). The user register, STATUS_TEMP, must be defined in Bank0. Within the 70h - 7Fh range (Bank0), wherever W_TEMP is expected the corresponding locations in the other banks should be dedicated for the possible saving of the W register. The steps of Example 8-2: 1. 2. 3. 4. 5. Stores the W register regardless of current bank. Stores the STATUS register in Bank0. Executes the Interrupt Service Routine (ISR) code. Restores the STATUS (and bank select bit register). Restores the W register. If additional locations need to be saved before executing the Interrupt Service Routine (ISR) code, they should be saved after the STATUS register is saved (step 2), and restored before the STATUS register is restored (step 4). Example 8-2: Saving the STATUS and W Registers in RAM (for Devices without Common RAM) MOVWF W_TEMP SWAPF STATUS,W BCF STATUS,RP0 MOVWF STATUS_TEMP ; ; ; ; ; ; ; ; Copy W to a Temporary Register regardless of current bank Swap STATUS nibbles and place into W register Change to Bank0 regardless of current bank Save STATUS to a Temporary register in Bank0 : : (Interrupt Service Routine (ISR) ) : SWAPF STATUS_TEMP,W ; Swap original STATUS register value ; into W (restores original bank) MOVWF STATUS ; Restore STATUS register from ; W register SWAPF W_TEMP,F ; Swap W_Temp nibbles and return ; value to W_Temp SWAPF W_TEMP,W ; Swap W_Temp to W to restore original ; W value without affecting STATUS DS31008A-page 8-12 1997 Microchip Technology Inc. Section 8. Interrupts Example 8-3 stores and restores the STATUS and W registers for devices with general purpose RAM only in Bank0 (such as the PIC16C620). The Bank must be tested before saving any of the user registers. , W_TEMP, must be defined across all banks and must be defined at the same offset from the bank base address. The user register, STATUS_TEMP, must be defined in Bank0. The steps of Example 8-3: 1. 2. 3. 4. 5. 6. Test current bank. Stores the W register regardless of current bank. Stores the STATUS register in Bank0. Executes the Interrupt Service Routine (ISR) code. Restores the STATUS (and bank select bit register). Restores the W register. If additional locations need to be saved before executing the Interrupt Service Routine (ISR) code, they should be saved after the STATUS register is saved (step 2), and restored before the STATUS register is restored (step 4). Example 8-3: Saving the STATUS and W Registers in RAM (for Devices with General Purpose RAM Only in Bank0) Push 1997 Microchip Technology Inc. DS31008A-page 8-13 8 Interrupts BTFSS STATUS, RP0 ; In Bank 0? GOTO RP0CLEAR ; YES, BCF STATUS, RP0 ; NO, Force to Bank 0 MOVWF W_TEMP ; Store W register SWAPF STATUS, W ; Swap STATUS register and MOVWF STATUS_TEMP ; store in STATUS_TEMP BSF STATUS_TEMP, 1 ; Set the bit that corresponds to RP0 GOTO ISR_Code ; Push completed RP0CLEAR MOVWF W_TEMP ; Store W register SWAPF STATUS, W ; Swap STATUS register and MOVWF STATUS_TEMP ; store in STATUS_TEMP ; ISR_Code : : (Interrupt Service Routine (ISR) ) : ; Pop SWAPF STATUS_TEMP, W ; Restore Status register MOVWF STATUS ; BTFSS STATUS, RP0 ; In Bank 1? GOTO Restore_WREG ; NO, BCF STATUS, RP0 ; YES, Force Bank 0 SWAPF W_TEMP, F ; Restore W register SWAPF W_TEMP, W ; BSF STATUS, RP0 ; Back to Bank 1 RETFIE ; POP completed Restore_WREG SWAPF W_TEMP, F ; Restore W register SWAPF W_TEMP, W ; RETFIE ; POP completed PICmicro MID-RANGE MCU FAMILY 8.6 Initialization Example 8-4 shows the initialization and enabling of device interrupts, where PIE1_MASK1 value is the value to write into the interrupt enable register. Example 8-5 shows how to create macro definitions for functions. Macros must be defined before they are used. For debugging ease, it may help if macros are placed in other files that are included at assembly time. This allows the source to be viewed without all the clutter of the required macros. These files must be included before the macro is used, but it simplifies debugging, if all include files are done at the top of the source file. Example 8-6 shows this structure. Example 8-7 shows a typical Interrupt Service Routine structure. This ISR uses macros for the saving and restoring of registers before the execution of the interrupt code. Example 8-4: Initialization and Enabling of Interrupts PIE1_MASK1 : : CLRF CLRF CLRF BSF MOVLW MOVWF BCF BSF EQU B`01101010' STATUS INTCON PIR1 STATUS, RP0 PIE1_MASK1 PIE1 STATUS, RP0 INTCON, GIE ; ; ; ; ; ; ; ; ; This is the Interrupt Enable ; Register mask value Bank0 Disable interrupts and clear some flags Clear all flag bits Bank1 This is the initial masking for PIE1 Bank0 Enable Interrupts Example 8-5: Register Saving / Restoring as Macros PUSH_MACRO MOVWF SWAPF STATUS,W MOVWF STATUS_TEMP ENDM ; POP_MACRO SWAPF MACRO STATUS_TEMP,W MOVWF STATUS SWAPF W_TEMP,F SWAPF W_TEMP,W ENDM DS31008A-page 8-14 MACRO W_TEMP ; ; ; ; ; ; ; ; This Macro Saves register contents Copy W to a Temporary Register regardless of current bank Swap STATUS nibbles and place into W register Save STATUS to a Temporary register in Bank0 End this Macro ; ; ; ; ; ; ; ; ; ; This Macro Restores register contents Swap original STATUS register value into W (restores original bank) Restore STATUS register from W register Swap W_Temp nibbles and return value to W_Temp Swap W_Temp to W to restore original W value without affecting STATUS End this Macro 1997 Microchip Technology Inc. Section 8. Interrupts Example 8-6: Source File Template ; ; LIST p = p16C77 Revision History ; List Directive, #INCLUDE #INCLUDE #INCLUDE ; Microchip Device Header File ; ; Include my standard macros ; File which includes macros specific ; to this application ; Specify Device Configuration Bits __CONFIG _XT_OSC & _PWRTE_ON & _BODEN_OFF & _CP_OFF & _WDT_ON ; org 0x00 ; Start of Program Memory RESET_ADDR : ; First instruction to execute after a reset end Example 8-7: Typical Interrupt Service Routine (ISR) org ISR_ADDR PUSH_MACRO T1_INT : BCF GOTO PIR1, TMR1IF END_ISR AD_INT : BCF PIR1, ADIF GOTO END_ISR LCD_INT : BCF PIR1, LCDIF GOTO END_ISR PORTB_INT : END_ISR POP_MACRO RETFIE 1997 Microchip Technology Inc. MACRO that saves required context registers, or in-line code Bank0 Timer1 overflow interrupt? YES NO, A/D interrupt? YES, do A/D thing NO, do this for all sources NO, LCD interrupt YES, do LCD thing NO, Change on PORTB interrupt? YES, Do PortB Change thing NO, do error recovery This is the trap if you enter the ISR but there were no expected interrupts Routine when the Timer1 overflows Clear the Timer1 overflow interrupt flag Ready to leave ISR (for this request) Routine when the A/D completes Clear the A/D interrupt flag Ready to leave ISR (for this request) Routine when the LCD Frame begins Clear the LCD interrupt flag Ready to leave ISR (for this request) Routine when PortB has a change MACRO that restores required registers, or in-line code Return and enable interrupts DS31008A-page 8-15 8 Interrupts CLRF STATUS BTFSC PIR1, TMR1IF GOTO T1_INT BTFSC PIR1, ADIF GOTO AD_INT : : BTFSC PIR1, LCDIF GOTO LCD_INT BTFSC INTCON, RBIF GOTO PORTB_INT INT_ERROR_LP1 GOTO INT_ERROR_LP1 ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; PICmicro MID-RANGE MCU FAMILY 8.7 Design Tips Question 1: An algorithm does not give the correct results. Answer 1: Assuming that the algorithm is correct and that interrupts are enabled during the algorithm, ensure that are registers that are used by the algorithm and by the interrupt service routine are saved and restored. If not some registers may be corrupted by the execution of the ISR. Question 2: My system seems to lock up. Answer 2: If interrupts are being used, ensure that the interrupt flag is cleared after servicing that interrupt (but before executing the RETFIE instruction). If the interrupt flag remains set when the RETFIE instruction is executed, program execution immediately returns to the interrupt vector, since there is an outstanding enabled interrupt. DS31008A-page 8-16 1997 Microchip Technology Inc. Section 8. Interrupts 8.8 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to this section are: Title Using the PortB Interrupt On Change as an External Interrupt Application Note # AN566 8 Interrupts 1997 Microchip Technology Inc. DS31008A-page 8-17 PICmicro MID-RANGE MCU FAMILY 8.9 Revision History Revision A This is the initial released revision of the interrupt description. DS31008A-page 8-18 1997 Microchip Technology Inc. M Section 9. I/O Ports HIGHLIGHTS This section of the manual contains the following major topics: 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.14 Introduction ....................................................................................................................9-2 PORTA and the TRISA Register ....................................................................................9-4 PORTB and the TRISB Register ....................................................................................9-6 PORTC and the TRISC Register....................................................................................9-8 PORTD and the TRISD Register....................................................................................9-9 PORTE and the TRISE Register ..................................................................................9-10 PORTF and the TRISF Register ..................................................................................9-11 PORTG and the TRISG Register .................................................................................9-12 GPIO and the TRISGP Register ..................................................................................9-13 I/O Programming Considerations.................................................................................9-14 Initialization ..................................................................................................................9-16 Design Tips ..................................................................................................................9-17 Related Application Notes............................................................................................9-19 Revision History ...........................................................................................................9-20 9 I/O Ports 1997 Microchip Technology Inc. DS31009A page 9-1 PICmicro MID-RANGE MCU FAMILY 9.1 Introduction General purpose I/O pins can be considered the simplest of peripherals. They allow the PICmicroTM to monitor and control other devices. To add flexibility and functionality to a device, some pins are multiplexed with an alternate function(s). These functions depend on which peripheral features are on the device. In general, when a peripheral is functioning, that pin may not be used as a general purpose I/O pin. For most ports, the I/O pin's direction (input or output) is controlled by the data direction register, called the TRIS register. TRIS controls the direction of PORT. A `1' in the TRIS bit corresponds to that pin being an input, while a `0' corresponds to that pin being an output. An easy way to remember is that a `1' looks like an I (input) and a `0' looks like an O (output). The PORT register is the latch for the data to be output. When the PORT is read, the device reads the levels present on the I/O pins (not the latch). This means that care should be taken with read-modify-write commands on the ports and changing the direction of a pin from an input to an output. Figure 9-1 shows a typical I/O port. This does not take into account peripheral functions that may be multiplexed onto the I/O pin. Reading the PORT register reads the status of the pins whereas writing to it will write to the port latch. All write operations (such as BSF and BCF instructions) are read-modify-write operations. Therefore a write to a port implies that the port pins are read, this value is modified, and then written to the port data latch. Figure 9-1: Typical I/O Port Data bus D Q VDD WR PORT Q CK P Data Latch I/O pin WR TRIS D Q CK Q N VSS TRIS Latch TTL or Schmitt Trigger RD TRIS Q D EN RD PORT Note: I/O pin has protection diodes to VDD and VSS. DS31009A-page 9-2 1997 Microchip Technology Inc. Section 9. I/O Ports When peripheral functions are multiplexed onto general I/O pins, the functionality of the I/O pins may change to accommodate the requirements of the peripheral module. Examples of this are the Analog-to-Digital (A/D) converter and LCD driver modules, which force the I/O pin to the peripheral function when the device is reset. In the case of the A/D, this prevents the device from consuming excess current if any analog levels were on the A/D pins after a reset occurred. With some peripherals, the TRIS bit is overridden while the peripheral is enabled. Therefore, read-modify-write instructions (BSF, BCF, XORWF) with TRIS as destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. PORT pins may be multiplexed with analog inputs and analog VREF input. The operation of each of these pins is selected, to be an analog input or digital I/O, by clearing/setting the control bits in the ADCON1 register (A/D Control Register1). When selected as an analog input, these pins will read as `0's. The TRIS registers control the direction of the port pins, even when they are being used as analog inputs. The user must ensure the TRIS bits are maintained set when using the pins as analog inputs. Note 1: If pins are multiplexed with Analog inputs, then on a Power-on Reset these pins are configured as analog inputs, as controlled by the ADCON1 register. Reading port pins configured as analog inputs read a `0'. Note 2: If pins are multiplexed with comparator inputs, then on a Power-on Reset these pins are configured as analog inputs, as controlled by the CMCON register. Reading port pins configured as analog inputs read a `0'. Note 3: If pins are multiplexed with LCD driver segments, then on a Power-on Reset these pins are configured as LCD driver segments, as controlled by the LCDSE register. To configure the pins as a digital port, the corresponding bits in the LCDSE register must be cleared. Any bit set in the LCDSE register overrides any bit settings in the corresponding TRIS register. Note 4: Pins may be multiplexed with the Parallel Slave Port (PSP). For the PSP to function, the I/O pins must be configured as digital inputs and the PSPMODE bit must be set. Note 5: At present the Parallel Slave Port (PSP) is only multiplexed onto PORTD and PORTE. The microprocessor port becomes enabled when the PSPMODE bit is set. In this mode, the user must make sure that the TRISE bits are set (pins are configured as digital inputs) and that PORTE is configured for digital I/O. PORTD will override the values in the TRISD register. In this mode the PORTD and PORTE input buffers are TTL. The control bits for the PSP operation are located in TRISE. 9 I/O Ports 1997 Microchip Technology Inc. DS31009A-page 9-3 PICmicro MID-RANGE MCU FAMILY 9.2 PORTA and the TRISA Register The RA4 pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. All pins have data direction bits (TRIS registers) which can configure these pins as output or input. Setting a TRISA register bit puts the corresponding output driver in a hi-impedance mode. Clearing a bit in the TRISA register puts the contents of the output latch on the selected pin(s). Example 9-1: Initializing PORTA CLRF CLRF STATUS PORTA BSF MOVLW MOVWF STATUS, RP0 0xCF TRISA ; ; ; ; ; ; ; Bank0 Initialize PORTA by clearing output data latches Select Bank1 Value used to initialize data direction PORTA<3:0> = inputs PORTA<5:4> = outputs TRISA<7:6> always read as '0' Figure 9-2: Block Diagram of RA3:RA0 and RA5 Pins Data bus D Q VDD WR PORT Q CK P Data Latch I/O pin WR TRIS D Q CK Q N VSS Analog input mode TRIS Latch TTL or ST input buffer RD TRIS Q D EN RD PORT To Peripheral Module(s) Note: I/O pin has protection diodes to VDD and VSS. DS31009A-page 9-4 1997 Microchip Technology Inc. Section 9. I/O Ports Figure 9-3: Block Diagram of RA4 Pin Data Bus WR PORT D Q CK Q RA4 pin N Data Latch VSS WR TRIS D Q CK Q Schmitt Trigger input buffer TRIS Latch RD TRIS Q D EN RD PORT To Peripheral Module Note: I/O pin has protection diodes to VSS only. 9 I/O Ports 1997 Microchip Technology Inc. DS31009A-page 9-5 PICmicro MID-RANGE MCU FAMILY 9.3 PORTB and the TRISB Register PORTB is an 8-bit wide bi-directional port. The corresponding data direction register is TRISB. Setting a bit in the TRISB register puts the corresponding output driver in a high-impedance input mode. Clearing a bit in the TRISB register puts the contents of the output latch on the selected pin(s). Example 9-2: Initializing PORTB CLRF CLRF STATUS PORTB BSF MOVLW MOVWF STATUS, RP0 0xCF TRISB ; ; ; ; ; ; ; Bank0 Initialize PORTB by clearing output data latches Select Bank1 Value used to initialize data direction PORTB<3:0> = inputs, PORTB<5:4> = outputs PORTB<7:6> = inputs Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. Figure 9-4: Block Diagram of RB3:RB0 Pins VDD RBPU(2) Data bus WR Port weak P pull-up Data Latch D Q I/O pin(1) CK TRIS Latch D Q WR TRIS TTL Input Buffer CK RD TRIS Q RD Port D EN To Peripheral Module Schmitt Trigger Buffer RD Port Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION<7>). DS31009A-page 9-6 1997 Microchip Technology Inc. Section 9. I/O Ports Four of PORTB's pins, RB7:RB4, have an interrupt on change feature. Only pins configured as inputs can cause this interrupt to occur (i.e. any RB7:RB4 pin configured as an output is excluded from the interrupt on change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are OR'ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). This interrupt can wake the device from SLEEP. The user, in the interrupt service routine, can clear the interrupt in the following manner: a) b) Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF. A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition, and allow flag bit RBIF to be cleared. This interrupt on mismatch feature, together with software configurable pull-ups on these four pins allow easy interface to a keypad and make it possible for wake-up on key-depression. The interrupt on change feature is recommended for wake-up on key depression and operations where PORTB is only used for the interrupt on change feature. Polling of PORTB is not recommended while using the interrupt on change feature. Figure 9-5: Block Diagram of RB7:RB4 Pins VDD RBPU(2) Data bus WR Port weak P pull-up Data Latch D Q I/O pin(1) CK TRIS Latch D Q WR TRIS TTL Input Buffer CK RD TRIS ST Buffer 9 Latch Q D EN RD Port Q1 From other RB7:RB4 pins Q D RD Port EN Q3 RB7:RB6 in serial programming mode Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION<7>). 3: In sleep mode the device is in Q1 state. 1997 Microchip Technology Inc. DS31009A-page 9-7 I/O Ports Set RBIF PICmicro MID-RANGE MCU FAMILY 9.4 PORTC and the TRISC Register PORTC is an 8-bit bi-directional port. Each pin is individually configurable as an input or output through the TRISC register. PORTC pins have Schmitt Trigger input buffers. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Example 9-3: Initializing PORTC CLRF CLRF STATUS PORTC BSF MOVLW MOVWF STATUS, RP0 0xCF TRISC ; ; ; ; ; ; ; Bank0 Initialize PORTC by clearing output data latches Select Bank1 Value used to initialize data direction PORTC<3:0> = inputs, PORTC<5:4> = outputs PORTC<7:6> = inputs Figure 9-6: PORTC Block Diagram (Peripheral Output Override) PORT/PERIPHERAL Select(1) Peripheral Data-out 0 VDD 1 Data Bus WR PORT D Q CK Q P Data Latch WR TRIS D Q CK Q I/O pin N TRIS Latch Peripheral OE(2) VSS RD TRIS Schmitt Trigger Q D RD PORT EN Peripheral input Note 1: Port/Peripheral select signal selects between port data and peripheral output. 2: Peripheral OE (output enable) is only activated if peripheral select is active. 3: I/O pins have diode protection to VDD and VSS. DS31009A-page 9-8 RD PORT 1997 Microchip Technology Inc. Section 9. I/O Ports 9.5 PORTD and the TRISD Register PORTD is an 8-bit port with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Example 9-4: Initializing PORTD CLRF CLRF STATUS PORTD BSF MOVLW MOVWF STATUS, RP0 0xCF TRISD ; ; ; ; ; ; ; Bank0 Initialize PORTD by clearing output data latches Select Bank1 Value used to initialize data direction PORTD<3:0> = inputs, PORTD<5:4> = outputs PORTD<7:6> = inputs Figure 9-7: Typical PORTD Block Diagram (in I/O Port Mode) Data Bus WR PORT D Q CK Q I/O pin Data Latch WR TRIS D Q CK Q Schmitt Trigger input buffer TRIS Latch RD TRIS Q D EN 9 RD PORT Note: I/O pins have protection diodes to VDD and VSS. I/O Ports 1997 Microchip Technology Inc. DS31009A-page 9-9 PICmicro MID-RANGE MCU FAMILY 9.6 PORTE and the TRISE Register PORTE can be up to an 8-bit port with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. Example 9-5: Initializing PORTE CLRF CLRF STATUS PORTE BSF MOVLW MOVWF STATUS, RP0 0x03 TRISE ; ; ; ; ; ; Bank0 Initialize PORTE by clearing output data latches Select Bank1 Value used to initialize data direction PORTE<1:0> = inputs, PORTE<7:2> = outputs Figure 9-8: Typical PORTE Block Diagram (in I/O Port Mode) Data Bus WR PORT D Q CK Q I/O pin Data Latch WR TRIS D Q CK Q Schmitt Trigger input buffer TRIS Latch RD TRIS Q D EN RD PORT Note: I/O pins have protection diodes to VDD and VSS. Note: DS31009A-page 9-10 On some devices with PORTE, the upper bits of the TRISE register are used for the Parallel Slave Port control and status bits. 1997 Microchip Technology Inc. Section 9. I/O Ports 9.7 PORTF and the TRISF Register PORTF is a digital input only port. Each pin is multiplexed with an LCD segment driver. These pins have Schmitt Trigger input buffers. Example 9-6: Initializing PORTF BCF BSF BCF BCF STATUS, RP0 STATUS, RP1 LCDSE, SE16 LCDSE, SE12 ; Select Bank2 ; ; Make all PORTF ; digital inputs Figure 9-9: PORTF LCD Block Diagram LCD Segment Data Digital Input/ LCD Output pin LCD Segment Output Enable LCDSE Schmitt Trigger input buffer Data Bus Q D EN RD PORT VDD RD TRIS Note: I/O pins have protection diodes to VDD and VSS. 9 I/O Ports 1997 Microchip Technology Inc. DS31009A-page 9-11 PICmicro MID-RANGE MCU FAMILY 9.8 PORTG and the TRISG Register PORTG is a digital input only port. Each pin is multiplexed with an LCD segment driver. These pins have Schmitt Trigger input buffers. Example 9-7: Initializing PORTG BCF BSF BCF BCF STATUS, RP0 STATUS, RP1 LCDSE, SE27 LCDSE, SE20 ; Select Bank2 ; ; Make all PORTG ; and PORTE<7> digital inputs Figure 9-10: PORTG LCD Block Diagram LCD Segment Data Digital Input/ LCD Output pin LCD Segment Output Enable LCDSE Schmitt Trigger input buffer Data Bus Q D EN RD PORT VDD RD TRIS DS31009A-page 9-12 1997 Microchip Technology Inc. Section 9. I/O Ports 9.9 GPIO and the TRISGP Register GPIO is an 8-bit I/O register. Only the low order six bits are implemented (GP5:GP0). Bits 7 and 6 are unimplemented and read as `0's. Any GPIO pin (except GP3) can be programmed individually as input or output. The GP3 pin is an input only pin. The TRISGP register controls the data direction for GPIO pins. A `1' in a TRISGP register bit puts the corresponding output driver in a hi-impedance mode. A `0' puts the contents of the output data latch on the selected pins, enabling the output buffer. The exceptions are GP3 which is input only and its TRIS bit will always read as '1'. Upon reset, the TRISGP register is all `1's, making all pins inputs. A read of the GPIO port, reads the pins not the output data latches. Any input must be present until read by an input instruction (e.g., MOVF GPIO,W). The outputs are latched and remain unchanged until the output latch is rewritten. Example 9-8: Initializing GPIO CLRF CLRF STATUS GPIO BSF MOVLW MOVWF STATUS, RP0 0xCF TRISGP ; ; ; ; ; ; ; Bank0 Initialize GPIO by clearing output data latches Select Bank1 Value used to initialize data direction GP<3:0> = inputs GP<5:4> = outputs TRISGP<7:6> always read as '0' Figure 9-11: Block Diagram of GP5:GP0 Pins Data Bus D WR Port W Reg Q Data Latch CK VDD Q P N D Q TRIS Latch TRIS `f' CK I/O pin(1) VSS 9 Q I/O Ports Reset RD Port Note 1: I/O pins have protection diodes to VDD and VSS. GP3 is input only with no data latch and no output drivers. The configuration word can set several I/O's to alternate functions. When acting as alternate functions the pins will read as `0' during port read. The GP0, GP1, and GP3 pins can be configured with weak pull-ups and also with interrupt on change. The interrupt on change and weak pull-up functions are not pin selectable. Interrupt on change is enabled by setting INTCON<3>. If the device configuration bits select one of the external oscillator modes, the GP4 and GP5 pin's GPIO functions are overridden and these pins are used for the oscillator. 1997 Microchip Technology Inc. DS31009A-page 9-13 PICmicro MID-RANGE MCU FAMILY 9.10 I/O Programming Considerations When using the ports (and GPIO) as I/O, design considerations need to be taken into account to ensure that the operation is as intended. 9.10.1 Bi-directional I/O Ports Any instruction which performs a write operation actually does a read followed by a write operation. The BCF and BSF instructions, for example, read the register into the CPU, execute the bit operation, and write the result back to the register. Caution must be used when these instructions are applied to a port with both inputs and outputs defined. For example, a BSF operation on bit5 of PORTB will cause all eight bits of PORTB to be read into the CPU. Then the BSF operation takes place on bit5 and PORTB is written to the output latches. If another bit of PORTB is used as a bi-directional I/O pin (e.g., bit0) and it is defined as an input at this time, the input signal present on the pin itself would be read into the CPU and rewritten to the data latch of this particular pin, overwriting the previous content. As long as the pin stays in the input mode, no problem occurs. However, if bit0 is switched to an output, the content of the data latch may now be unknown. Reading the port register, reads the values of the port pins. Writing to the port register writes the value to the port latch. When using read-modify-write instructions (ex. BCF, BSF, etc.) on a port, the value of the port pins is read, the desired operation is performed on this value, and the value is then written to the port latch. Example 9-9 shows the effect of two sequential read-modify-write instructions on an I/O port. Example 9-9: Read-Modify-Write Instructions on an I/O Port ; Initial PORT settings: PORTB<7:4> Inputs ; PORTB<3:0> Outputs ; PORTB<7:6> have external pull-ups and are not connected to other circuitry ; ; PORT latch PORT pins ; ---------- --------BCF PORTB, 7 ; 01pp pppp 11pp pppp BCF PORTB, 6 ; 10pp pppp 11pp pppp BSF STATUS, RP0 ; BCF TRISB, 7 ; 10pp pppp 11pp pppp BCF TRISB, 6 ; 10pp pppp 10pp pppp ; ; Note that the user may have expected the pin values to be 00pp ppp. ; The 2nd BCF caused RB7 to be latched as the pin value (high). A pin configured as an output, actively driving a Low or High should not be driven from external devices at the same time in order to change the level on this pin ("wired-or," "wired-and"). The resulting high output currents may damage the chip. DS31009A-page 9-14 1997 Microchip Technology Inc. Section 9. I/O Ports 9.10.2 Successive Operations on an I/O Port The actual write to an I/O port happens at the end of an instruction cycle, whereas for reading, the data must be valid at the beginning of the instruction cycle (Figure 9-12). Therefore, care must be exercised if a write followed by a read operation is carried out on the same I/O port. The sequence of instructions should be such to allow the pin voltage to stabilize (load dependent) before the next instruction which causes that file to be read into the CPU is executed. Otherwise, the previous state of that pin may be read into the CPU rather than the new state. When in doubt, it is better to separate these instructions with a NOP or another instruction not accessing this I/O port. Figure 9-12: Successive I/O Operation Q1 PC Instruction fetched Q2 Q3 Q4 Q1 PC Q2 Q4 Q3 Q1 PC + 1 MOVWF PORTB write to PORTB Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC + 3 PC + 2 MOVF PORTB,W NOP NOP RB7:RB0 Port pin sampled here TPD Instruction executed NOP MOVWF PORTB write to PORTB MOVF PORTB,W This example shows a write to PORTB followed by a read from PORTB. Note: Data setup time = (0.25TCY - TPD) whereTCY = instruction cycle TPD = propagation delay Therefore, at higher clock frequencies, a write followed by a read may be problematic due to external capacitance. Figure 9-13 shows the I/O model which causes this situation. As the effective capacitance (C) becomes larger, the rise/fall time of the I/O pin increases. As the device frequency increases or the effective capacitance increases, the possibility of this subsequent PORTx read-modify-write instruction issue increases. This effective capacitance includes the effects of the board traces. The use of NOP instructions between the subsequent PORTx read-modify-write instructions, is a lower cost solution, but has the issue that the number of NOP instructions is dependent on the effective capacitance C and the frequency of the device. Figure 9-13: I/O Connection Issues BSF PORTx, PINy PIC16CXXX Q2 I/O Q3 Q4 BSF PORTx, PINz Q1 Q2 Q3 Q4 Q1 VIL C(1) PORTx, PINy Read PORTx, PINy as low Note: This is not a capacitor to ground, but the effective capacitive loading on the trace. 1997 Microchip Technology Inc. BSF PORTx, PINz clears the value to be driven on the PORTx, PINy pin. DS31009A-page 9-15 I/O Ports The best way to address this is to add an series resistor at the I/O pin. This resistor allows the I/O pin to get to the desired level before the next instruction. 9 PICmicro MID-RANGE MCU FAMILY 9.11 Initialization See the section describing each port for examples of initialization of the ports. Note: DS31009A-page 9-16 It is recommended that when initializing the port, the data latch (PORT register) should be initialized first, and then the data direction (TRIS register). This will eliminate a possible pin glitch, since the PORT data latch values power up in a random state. 1997 Microchip Technology Inc. Section 9. I/O Ports 9.12 Design Tips Question 1: Code will not toggle any I/O ports, but the oscillator is running. What can I be doing wrong? Answer 1: 1. 2. 3. 4. 5. 6. Have the TRIS registers been initialized properly? These registers can be written to directly in the second bank (Bank1). In most cases the user is not switching to Bank1 (BSF STATUS,RP0) before writing zeros to the TRIS register. If you are setting up the TRIS registers properly in Bank1 (RP0 = 1), you may not be returning to Bank0 before writing to the ports (BCF STATUS,RP0). Is there a peripheral multiplexed onto those pins that are enabled? Is the Watchdog Timer enabled (done at programming)? If it is enabled, is it being cleared properly with a CLRWDT instruction at least every 9 ms (or more if prescaled)? Are you using the correct instructions to write to the port? More than one person has used the MOVF command when they should have used MOVWF. For parts with interrupts, are the interrupts disabled? If not, try disabling them to verify they are not interfering. Question 2: When my program reads a port, I get a different value than what I put in the port register. What can cause this? Answer 2: 1. 2. 3. When a port is read, it is always the pin that is read, regardless of its being set to input or output. So if a pin is set to an input, you will read the value on the pin regardless of the register value. If a pin is set to output, say it has a one in the data latch; if it is shorted to ground you will still read a zero on the pin. This is very useful for building fault tolerant systems, or handling I2CTM bus conflicts. (The I2C bus is only driven low, and the pin is tristated for a one. If the pin is low and you are not driving it, some other device is trying to take the bus). Mid-Range MCU devices all have at least one open drain (or open collector) pin. These pins can only drive a zero or tristate. For most Mid-Range devices this is pin RA4. Open drain pins must have a pull-up resistor to have a high state. This pin is useful for driving odd voltage loads. The pull-up can be connected to a voltage (typically less than VDD) which becomes the high state. Question 3: I have a PIC16CXXX with pin RB0 configured as an interrupt input, but am not getting interrupted. When I change my routine to poll the pin, it reads the high input and operates fine. What is the problem? 9 Answer 3: I2C is a trademark of Philips Corporation. 1997 Microchip Technology Inc. DS31009A-page 9-17 I/O Ports PORTB accepts TTL input levels (on most parts), so when you have an input of say 3V (with VDD = 5V), you will read a one. However the buffer to the interrupt structure from pin RB0 is Schmitt Trigger, which requires a higher voltage (than TTL input) before the high input is registered. So it is possible to read a one, but not get the interrupt. The interrupt was given a Schmitt Trigger input with hysteresis to minimize noise problems. It is one thing to have short noise spikes on a pin that is a data input that can potentially cause bad data, but quite another to permit noise to cause an interrupt, hence the difference. PICmicro MID-RANGE MCU FAMILY Question 4: When I perform a BCF instruction, other pins get cleared in the port. Why? Answer 4: 1. 2. DS31009A-page 9-18 Another case where a read-modify-write instruction may seem to change other pin values unexpectedly can be illustrated as follows: Suppose you make PORTC all outputs and drive the pins low. On each of the port pins is an LED connected to ground, such that a high output lights it. Across each LED is a 100 F capacitor. Let's also suppose that the processor is running very fast, say 20 MHz. Now if you go down the port setting each pin in order; BSF PORTC,0 then BSF PORTC,1 then BSF PORTC,2 and so on, you may see that only the last pin was set, and only the last LED actually turns on. This is because the capacitors take a while to charge. As each pin was set, the pin before it was not charged yet and so was read as a zero. This zero is written back out to the port latch (r-m-w, remember) which clears the bit you just tried to set the instruction before. This is usually only a concern at high speeds and for successive port operations, but it can happen, so take it into consideration. If this is on a PIC16C7XX device, you have not configured the I/O pins properly in the ADCON1 register. If a pin is configured for analog input, any read of that pin will read a zero, regardless of the voltage on the pin. This is an exception to the normal rule that the pin state is always read. You can still configure an analog pin as an output in the TRIS register, and drive the pin high or low by writing to it, but you will always read a zero. Therefore if you execute a Read-Modify-Write instruction (see previous question) all analog pins are read as zero, and those not directly modified by the instruction will be written back to the port latch as zero. A pin configured as analog is expected to have values that may be neither high nor low to a digital pin, or floating. Floating inputs on digital pins are a no-no, and can lead to high current draw in the input buffer, so the input buffer is disabled. 1997 Microchip Technology Inc. Section 9. I/O Ports 9.13 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to I/O ports are: Title Application Note # Improving the Susceptibility of an Application to ESD AN595 Clock Design using Low Power/Cost Techniques AN615 Implementing Wake-up on Keystroke AN528 Interfacing to AC Power Lines AN521 Multiplexing LED Drive and a 4 x 4 Keypad Sampling AN529 Using PIC16C5X as an LCD Drivers AN563 Serial Port Routines Without Using TMR0 AN593 Implementation of an Asynchronous Serial I/O AN510 Using the PORTB Interrupt on Change Feature as an External Interrupt AN566 Implementing Wake-up on Keystroke AN522 Apple Desktop Bus AN591 Software Implementation of Asynchronous Serial I/O AN555 2C AN515 Communicating with the I Bus using the PIC16C5X Interfacing 93CX6 Serial EEPROMs to the PIC16C5X Microcontrollers AN530 Logic Powered Serial EEPROMs AN535 Interfacing 24LCXXB Serial EEPROMs to the PIC16C54 AN567 Using the 24XX65 and 24XX32 with Stand-alone PIC16C54 Code AN558 9 I/O Ports 1997 Microchip Technology Inc. DS31009A-page 9-19 PICmicro MID-RANGE MCU FAMILY 9.14 Revision History Revision A This is the initial released revision of the I/O Ports description. DS31009A-page 9-20 1997 Microchip Technology Inc. M Section 10. Parallel Slave Port HIGHLIGHTS This section of the manual contains the following major topics: 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 Introduction ..................................................................................................................10-2 Control Register ...........................................................................................................10-3 Operation .....................................................................................................................10-4 Operation in Sleep Mode .............................................................................................10-5 Effect of a Reset...........................................................................................................10-5 PSP Waveforms ...........................................................................................................10-5 Design Tips ..................................................................................................................10-6 Related Application Notes............................................................................................10-7 Revision History ...........................................................................................................10-8 10 Parallel Slave Port 1997 Microchip Technology Inc. DS31010A page 10-1 PICmicro MID-RANGE MCU FAMILY 10.1 Introduction Some devices have an 8-bit wide Parallel Slave Port (PSP). This port is multiplexed onto one of the devices I/O ports. The PORT operates as an 8-bit wide Parallel Slave Port, or microprocessor port, when the PSPMODE control bit is set. In this mode, the input buffers are TTL. In slave mode the module is asynchronously readable and writable by the external world through RD control input pin and the WR control input pin. It can directly interface to an 8-bit microprocessor data bus. The external microprocessor can read or write the PORT latch as an 8-bit latch. Setting the PSPMODE bit enables port pins to be the RD input, the WR input, and the CS (chip select) input. Note 1: At present the Parallel Slave Port (PSP) is only multiplexed onto PORTD and PORTE. The microprocessor port becomes enabled when the PSPMODE bit is set. In this mode, the user must make sure that PORTD and PORTE are configured as digital I/O. That is, peripheral modules multiplexed onto the PSP functions are disabled (such as the A/D). When PORTE is configured for digital I/O. PORTD will override the values in the TRISD register. Note 2: In this mode the PORTD and PORTE input buffers are TTL. The control bits for the PSP operation are located in TRISE. There are actually two 8-bit latches, one for data-out (from the PICmicro) and one for data input. The user writes 8-bit data to PORT data latch and reads data from the port pin latch (note that they have the same address). In this mode, the TRIS register is ignored, since the microprocessor is controlling the direction of data flow. Figure 10-1 shows the block diagram for the PSP. Figure 10-1: PORTD and PORTE Block Diagram (Parallel Slave Port) Data bus D WR Port Q PSP7:PSP0 CK EN Q D TTL RD Port EN EN One bit of PORTD Set interrupt flag PSPIF Read Chip Select Write TTL RD TTL CS TTL WR Note: I/O pins have protection diodes to VDD and VSS. DS31010A-page 10-2 1997 Microchip Technology Inc. Section 10. Parallel Slave Port 10.2 Control Register Register 10-1: TRISE Register R-0 IBF bit 7 bit 7 R-0 OBF R/W-0 IBOV R/W-0 PSPMODE U-0 -- R/W-1 TRISE2 R/W-1 TRISE1 R/W-1 TRISE0 bit 0 IBF: Input Buffer Full Status bit 1 = A word has been received and waiting to be read by the CPU 0 = No word has been received bit 6 OBF: Output Buffer Full Status bit 1 = The output buffer still holds a previously written word 0 = The output buffer has been read bit 5 IBOV: Input Buffer Overflow Detect bit (in microprocessor mode) 1 = A write occurred when a previously input word has not been read (must be cleared in software) 0 = No overflow occurred bit 4 PSPMODE: Parallel Slave Port Mode Select bit 1 = Parallel slave port mode 0 = General purpose I/O mode bit 3 Unimplemented: Read as '0' bit 2 TRISE2: RE2 direction control bit 1 = Input 0 = Output bit 1 TRISE1: RE1 direction control bit 1 = Input 0 = Output bit 0 TRISE0: RE0 direction control bit 1 = Input 0 = Output Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 10 Parallel Slave Port 1997 Microchip Technology Inc. DS31010A-page 10-3 PICmicro MID-RANGE MCU FAMILY 10.3 Operation A write to the PSP from the external system, occurs when both the CS and WR lines are first detected low. When either the CS or WR lines become high (edge triggered), the Input Buffer Full status flag bit IBF (TRISE<7>) is set on the Q4 clock cycle, following the next Q2 cycle, to signal the write is complete. The interrupt flag bit, PSPIF, is also set on the same Q4 clock cycle. The IBF flag bit is inhibited from being cleared for additional TCY cycles (see parameter 66). If the IBF flag bit is cleared by reading the PORTD input latch, and this has to be a read-only instruction (i.e., MOVF) and not a read-modify-write instruction. The input Buffer Overflow status flag bit IBOV (TRISE<5>) is set if a second write to the Parallel Slave Port is attempted when the previous byte has not been read out of the buffer. A read from the PSP from the external system, occurs when both the CS and RD lines are first detected low. The Output Buffer Full status flag bit OBF (TRISE<6>) is cleared immediately indicating that the PORTD latch was read by the external bus. When either the CS or RD pin becomes high (edge triggered), the interrupt flag bit PSPIF is set on the Q4 clock cycle, following the next Q2 cycle, indicating that the read is complete. OBF remains low until data is written to PORTD by the user firmware. Input Buffer Full Status Flag bit IBF, is set if a received word is waiting to be read by the CPU. Once the PORT input latch is read, the IBF bit is cleared. The IBF bit is a read only status bit. Output Buffer Full Status Flag bit OBF, is set if a word written to PORT latch is waiting to be read by the external bus. Once the PORTD output latch is read by the microprocessor, OBF is cleared. Input Buffer Overflow Status Flag bit IBOV is set if a second write to the microprocessor port is attempted when the previous word has not been read by the CPU (the first word is retained in the buffer). When not in Parallel Slave Port mode, the IBF and OBF bits are held clear. However, if flag bit IBOV was previously set, it must be cleared in the software. An interrupt is generated and latched into flag bit PSPIF when a read or a write operation is completed. Interrupt flag bit PSPIF must be cleared by user software and the interrupt can be disabled by clearing interrupt enable bit PSPIE. Table 10-1: PORTE Functions Name RD WR CS Note: DS31010A-page 10-4 Function Read Control Input in parallel slave port mode: RD 1 = Not a read operation 0 = Read operation. Reads PORTD register (if chip selected) Write Control Input in parallel slave port mode: WR 1 = Not a write operation 0 = Write operation. Writes PORTD register (if chip selected) Chip Select Control Input in parallel slave port mode: CS 1 = Device is not selected 0 = Device is selected The PSP may have other functions multiplexed onto the same pins. For the PSP to operate, the pins must be configured as digital I/O. 1997 Microchip Technology Inc. Section 10. Parallel Slave Port 10.4 Operation in Sleep Mode When in sleep mode the microprocessor may still read and write the Parallel Slave Port. These actions will set the PSPIF bit. If the PSP interrupts are enabled, this will wake the processor from sleep mode so that the PSP data latch may be either read, or written with the next value for the microprocessor. 10.5 Effect of a Reset After any reset the PSP is disabled and PORTD and PORTE are forced to their default mode. 10.6 PSP Waveforms Figure 10-2 shows the waveform for a write from the microprocessor to the PSP, while Figure 10-3 shows the waveform for a read of the PSP by the microprocessor. Figure 10-2: Parallel Slave Port Write Waveforms Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q2 Q3 Q4 CS WR RD PORTD<7:0> IBF OBF PSPIF Note: The IBF flag bit is inhibited from being cleared until after this point. Figure 10-3: Parallel Slave Port Read Waveforms Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 CS WR RD PORTD<7:0> IBF 10 OBF PSPIF Parallel Slave Port 1997 Microchip Technology Inc. DS31010A-page 10-5 PICmicro MID-RANGE MCU FAMILY 10.7 Design Tips Question 1: Migrating from the PIC16C74 to the PIC16C74A, the operation of the PSP seems to have changed. Answer 1: Yes, a design change was made so the PIC16C74A is edge sensitive (while the PIC16C74 was level sensitive). See Appendix C.9 for more information. DS31010A-page 10-6 1997 Microchip Technology Inc. Section 10. Parallel Slave Port 10.8 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Parallel Slave Port are: Title Using the 8-bit Parallel Slave Port Application Note # AN579 10 Parallel Slave Port 1997 Microchip Technology Inc. DS31010A-page 10-7 PICmicro MID-RANGE MCU FAMILY 10.9 Revision History Revision A This is the initial released revision of the Parallel Slave Port description. DS31010A-page 10-8 1997 Microchip Technology Inc. M 11 Timer0 Section 11. Timer0 HIGHLIGHTS This section of the manual contains the following major topics: 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 Introduction ..................................................................................................................11-2 Control Register ...........................................................................................................11-3 Operation .....................................................................................................................11-4 TMR0 Interrupt.............................................................................................................11-5 Using Timer0 with an External Clock ...........................................................................11-6 TMR0 Prescaler ...........................................................................................................11-7 Design Tips ................................................................................................................11-10 Related Application Notes..........................................................................................11-11 Revision History .........................................................................................................11-12 1997 Microchip Technology Inc. DS31011A page 11-1 PICmicro MID-RANGE MCU FAMILY 11.1 Introduction The Timer0 module has the following features: * * * * * * 8-bit timer/counter Readable and writable 8-bit software programmable prescaler Clock source selectable to be external or internal Interrupt on overflow from FFh to 00h Edge select for external clock Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. Figure 11-1 shows a simplified block diagram of the Timer0 module. Figure 11-1: Timer0 Block Diagram Data bus FOSC/4 0 PSout 1 1 Programmable Prescaler T0CKI pin 0 8 Sync with Internal clocks TMR0 PSout (2 cycle delay) T0SE 3 PS2, PS1, PS0 T0CS PSA Set interrupt flag bit T0IF on overflow Note 1: T0CS, T0SE, PSA, PS2:PS0 (OPTION_REG<5:0>). 2: The prescaler is shared with Watchdog Timer (refer to Figure 11-6 for detailed block diagram). DS31011A-page 11-2 1997 Microchip Technology Inc. Section 11. Timer0 11.2 11 Control Register Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. Register 11-1: OPTION_REG Register R/W-1 RBPU (1) bit 7 R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA bit 7 RBPU (1): Weak Pull-up Enable bit 1 = Weak pull-ups are disabled 0 = Weak pull-ups are enabled by individual port latch values bit 6 INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of INT pin 0 = Interrupt on falling edge of INT pin bit 5 T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4 T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module bit 2:0 PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: Some devices call this bit GPPU. Devices that have the RBPU bit, have the weak pull-ups on PORTB, while devices that have the GPPU have the weak pull-ups on the GPIO Port. 1997 Microchip Technology Inc. DS31011A-page 11-3 Timer0 The OPTION_REG register is a readable and writable register which contains various control bits to configure the TMR0/WDT prescaler, the External INT Interrupt, TMR0, and the weak pull-ups on PORTB. PICmicro MID-RANGE MCU FAMILY 11.3 Operation Timer mode is selected by clearing the T0CS bit (OPTION<5>). In timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles (Figure 11-2 and Figure 11-3). The user can work around this by writing an adjusted value to the TMR0 register. Counter mode is selected by setting the T0CS bit (OPTION<5>). In counter mode, Timer0 will increment either on every rising or falling edge of the T0CKI pin. The incrementing edge is determined by the Timer0 Source Edge Select the T0SE bit (OPTION<4>). Clearing the T0SE bit selects the rising edge. Restrictions on the external clock input are discussed in detail in Subsection 11.5 "Using Timer0 with an External Clock" . The prescaler is mutually exclusively shared between the Timer0 module and the Watchdog Timer. The prescaler assignment is controlled in software by the PSA control bit (OPTION<3>). Clearing the PSA bit will assign the prescaler to the Timer0 module. The prescaler is not readable or writable. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4,..., 1:256 are selectable. Subsection 11.6 "TMR0 Prescaler" details the operation of the prescaler. Any write to the TMR0 register will cause a 2 instruction cycle (2TCY) inhibit. That is, after the TMR0 register has been written with the new value, TMR0 will not be incremented until the third instruction cycle later (Figure 11-2). When the prescaler is assigned to the Timer0 module, any write to the TMR0 register will immediately update the TMR0 register and clear the prescaler. The incrementing of Timer0 (TMR0 and Prescaler) will also be inhibited 2 instruction cycles (TCY). So if the prescaler is configured as 2, then after a write to the TMR0 register TMR0 will not increment for 4 Timer0 clocks (Figure 11-3). After that, TMR0 will increment every prescaler number of clocks later. Figure 11-2: Timer0 Timing: Internal Clock/No Prescale PC (Program Counter) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC-1 Instruction Fetch TMR0 PC PC+1 MOVWF TMR0 T0 T0+1 Instruction Executed PC+2 PC+3 PC+4 PC+5 PC+6 MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W T0+2 NT0 NT0 NT0 Write TMR0 executed Read TMR0 reads NT0 Read TMR0 reads NT0 NT0+1 Read TMR0 reads NT0 NT0+2 T0 Read TMR0 Read TMR0 reads NT0 + 1 reads NT0 + 2 Figure 11-3: Timer0 Timing: Internal Clock/Prescale 1:2 PC (Program Counter) Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC-1 MOVWF TMR0 Instruction Fetch TMR0 PC T0 Instruction Execute DS31011A-page 11-4 PC+1 PC+2 PC+3 PC+4 PC+5 PC+6 MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W T0+1 NT0+1 NT0 Write TMR0 executed Read TMR0 reads NT0 Read TMR0 reads NT0 Read TMR0 reads NT0 Read TMR0 reads NT0 Read TMR0 reads NT0 + 1 1997 Microchip Technology Inc. Section 11. Timer0 11.4 11 TMR0 Interrupt Figure 11-4: TMR0 Interrupt Timing Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT(3) Timer0 FEh T0IF bit FFh 00h 01h 02h 1 1 GIE bit INSTRUCTION FLOW PC PC Instruction fetched Inst (PC) Instruction executed Inst (PC-1) PC +1 PC +1 Inst (PC+1) Inst (PC) Dummy cycle 0004h 0005h Inst (0004h) Inst (0005h) Dummy cycle Inst (0004h) Note 1: Interrupt flag bit T0IF is sampled here (every Q1). 2: Interrupt latency = 4TCY where TCY = instruction cycle time. 3: CLKOUT is available only in RC oscillator mode. 1997 Microchip Technology Inc. DS31011A-page 11-5 Timer0 The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module interrupt service routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP since the timer is shut-off during SLEEP. See Figure 11-4 for Timer0 interrupt timing. PICmicro MID-RANGE MCU FAMILY 11.5 Using Timer0 with an External Clock When an external clock input is used for Timer0, it must meet certain requirements as detailed in 11.5.1 "External Clock Synchronization." These requirements ensure the external clock can be synchronized with the internal phase clock (TOSC). Also, there is a delay in the actual incrementing of Timer0 after synchronization. 11.5.1 External Clock Synchronization When no prescaler is used, the external clock input is the same as the prescaler output. The synchronization of T0CKI with the internal phase clocks is accomplished by sampling the prescaler output on the Q2 and Q4 cycles of the internal phase clocks (Figure 11-5). Therefore, it is necessary for T0CKI to be high for at least 2Tosc (and a small RC delay of 20 ns) and low for at least 2Tosc (and a small RC delay of 20 ns). Refer to parameters 40, 41 and 42 in the electrical specification of the desired device. When a prescaler is used, the external clock input is divided by an asynchronous ripple-counter type prescaler so that the prescaler output is symmetrical. For the external clock to meet the sampling requirement, the ripple-counter must be taken into account. Therefore, it is necessary for T0CKI to have a period of at least 4Tosc (and a small RC delay of 40 ns) divided by the prescaler value. The only requirement on T0CKI high and low time is that they do not violate the minimum pulse width requirement of 10 ns. Refer to parameters 40, 41 and 42 in the electrical specification of the desired device. 11.5.2 TMR0 Increment Delay Since the prescaler output is synchronized with the internal clocks, there is a small delay from the time the external clock edge occurs to the time the Timer0 module is actually incremented. Figure 11-5 shows the delay from the external clock edge to the timer incrementing. Figure 11-5: Timer0 Timing with External Clock Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 External Clock Input or Prescaler output (2) Q1 Q2 Q3 Q4 Small pulse misses sampling (1) (3) External Clock/Prescaler Output after sampling Increment Timer0 (Q4) Timer0 T0 T0 + 1 T0 + 2 Note 1: Delay from clock input change to Timer0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc). Therefore, the error in measuring the interval between two edges on Timer0 input = 4Tosc max. 2: External clock if no prescaler selected, Prescaler output otherwise. 3: The arrows indicate the points in time where sampling occurs. DS31011A-page 11-6 1997 Microchip Technology Inc. Section 11. Timer0 11.6 11 TMR0 Prescaler Note: There is only one prescaler available which is mutually exclusively shared between the Timer0 module and the Watchdog Timer. The PSA and PS2:PS0 bits (OPTION<3:0>) determine the prescaler assignment and prescale ratio. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF TMR0, MOVWF TMR0, BSF TMR0,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the Watchdog Timer. The prescaler is not readable or writable. Figure 11-6: Block Diagram of the Timer0/WDT Prescaler CLKOUT (=Fosc/4) Data Bus 0 T0CKI pin 8 M U X 1 M U X 0 1 SYNC 2 Cycles TMR0 reg T0SE T0CS 0 Watchdog Timer M U X 1 Set T0IF flag bit on Overflow PSA 8-bit Prescaler 8 8 - to - 1MUX PS2:PS0 PSA WDT Enable bit 1 0 MUX PSA WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>). 1997 Microchip Technology Inc. DS31011A-page 11-7 Timer0 An 8-bit counter is available as a prescaler for the Timer0 module, or as a postscaler for the Watchdog Timer (Figure 11-6). For simplicity, this counter is being referred to as "prescaler" in the Timer0 description. Thus, a prescaler assignment for the Timer0 module means that there is no postscaler for the Watchdog Timer, and vice-versa. PICmicro MID-RANGE MCU FAMILY 11.6.1 Switching Prescaler Assignment The prescaler assignment is fully under software control, i.e., it can be changed "on the fly" during program execution. Note: To avoid an unintended device RESET, the following instruction sequence (shown in Example 11-1) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled. In Example 11-1, the first modification of the OPTION_REG does not need to be included if the final desired prescaler is other then 1:1. If the final prescaler value is to be 1:1, then a temporary prescale value is set (other than 1:!), and the final prescale value is set in the last modification of OPTION_REG. Example 11-1: Changing Prescaler (Timer0WDT) Lines 2 and 3 do NOT have to be included if the final desired prescale value is other than 1:1. If 1:1 is final desired value, then a temporary prescale value is set in lines 2 and 3 and the final prescale value will be set in lines 10 and 11. 1) BSF STATUS, RP0 ;Bank1 2) 3) MOVLW MOVWF b'xx0x0xxx' OPTION_REG ;Select clock source and prescale value of ;other than 1:1 4) 5) BCF CLRF STATUS, RP0 TMR0 ;Bank0 ;Clear TMR0 and prescaler 6) 7) 8) BSF MOVLW MOVWF STATUS, RP1 b'xxxx1xxx' OPTION_REG ;Bank1 ;Select WDT, do not change prescale value ; 9) CLRWDT 10) MOVLW b'xxxx1xxx' ;Clears WDT and prescaler ;Select new prescale value and WDT 11) MOVWF 12) BCF ; ;Bank0 OPTION_REG STATUS, RP0 To change prescaler from the WDT to the Timer0 module use the sequence shown in Example 11-2. Example 11-2: Changing Prescaler (WDTTimer0) CLRWDT BSF MOVLW MOVWF BCF DS31011A-page 11-8 STATUS, RP0 b'xxxx0xxx' OPTION_REG STATUS, RP0 ; ; ; ; ; Clear WDT and prescaler Bank1 Select TMR0, new prescale value and clock source Bank0 1997 Microchip Technology Inc. Section 11. Timer0 11.6.2 11 Initialization Example 11-3: Timer0 Initialization (Internal Clock Source) CLRF CLRF BSF MOVLW MOVWF TMR0 INTCON STATUS, RP0 0xC3 OPTION_REG ; ; ; ; ; ; ; ; ; ; Clear Timer0 register Disable interrupts and clear T0IF Bank1 PortB pull-ups are disabled, Interrupt on rising edge of RB0 Timer0 increment from internal clock with a prescaler of 1:16. Bank0 Enable TMR0 interrupt Enable all interrupts BCF STATUS, RP0 ;** BSF INTCON, T0IE ;** BSF INTCON, GIE ; ; The TMR0 interrupt is disabled, do polling on the overflow bit ; T0_OVFL_WAIT BTFSS INTCON, T0IF GOTO T0_OVFL_WAIT ; Timer has overflowed Example 11-4: Timer0 Initialization (External Clock Source) CLRF CLRF BSF MOVLW MOVWF TMR0 INTCON STATUS, RP0 0x37 OPTION_REG ; ; ; ; ; ; ; ; ; ; ; Clear Timer0 register Disable interrupts and clear T0IF Bank1 PortB pull-ups are enabled, Interrupt on falling edge of RB0 Timer0 increment from external clock on the high-to-low transition of T0CKI with a prescaler of 1:256. Bank0 Enable TMR0 interrupt Enable all interrupts BCF STATUS, RP0 ;** BSF INTCON, T0IE ;** BSF INTCON, GIE ; ; The TMR0 interrupt is disabled, do polling on the overflow bit ; T0_OVFL_WAIT BTFSS INTCON, T0IF GOTO T0_OVFL_WAIT ; Timer has overflowed 1997 Microchip Technology Inc. DS31011A-page 11-9 Timer0 Since Timer0 has a software programmable clock source, there are two examples to show the initialization of Timer0 with each source. Example 11-3 shows the initialization for the internal clock source (timer mode), while Example 11-4 shows the initialization for the external clock source (counter mode). PICmicro MID-RANGE MCU FAMILY 11.7 Design Tips I am implementing a counter/clock, but the clock loses time or is inaccurate. Question 1: Answer 1: If you are polling TMR0 to see if it has rolled over to zero. You could do this by executing: wait MOVF BTFSS TMR0,W STATUS,Z GOTO wait ; read the timer into W ; see if it was zero, if so, ; break from loop ; if not zero yet, keep waiting Two possible scenarios to lose clock cycles are: 1. If you are incrementing TMR0 from the internal instruction clock, or an external source that is about as fast, the overflow could occur during the two cycle GOTO, so you could miss it. In this case the TMR0 source should be prescaled. Or you could do a test to see if it has rolled over by checking for less than a nominal value: Wait 2. DS31011A-page 11-10 movlw subwf btfsc goto 3 TMR0,W STATUS,C Wait When writing to TMR0, two instruction clock cycles are lost. Often you have a specific time period you want to count, say 100 decimal. In that case you might put 156 into TMR0 (256 - 100 = 156). However, since two instruction cycles are lost when you write to TMR0 (for internal logic synchronization), you should actually write 158 to the timer. 1997 Microchip Technology Inc. Section 11. Timer0 11.8 11 Related Application Notes Title Application Note # Frequency Counter Using PIC16C5X AN592 A Clock Design using the PIC16C54 for LED Display and Switch Inputs AN590 1997 Microchip Technology Inc. DS31011A-page 11-11 Timer0 This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Timer0 are: PICmicro MID-RANGE MCU FAMILY 11.9 Revision History Revision A This is the initial released revision of the Timer0 Module description. DS31011A-page 11-12 1997 Microchip Technology Inc. M Section 12. Timer1 HIGHLIGHTS This section of the manual contains the following major topics: 12 1997 Microchip Technology Inc. DS31012A page 12-1 Timer1 12.1 Introduction ..................................................................................................................12-2 12.2 Control Register ...........................................................................................................12-3 12.3 Timer1 Operation in Timer Mode .................................................................................12-4 12.4 Timer1 Operation in Synchronized Counter Mode.......................................................12-4 12.5 Timer1 Operation in Asynchronous Counter Mode......................................................12-5 12.6 Timer1 Oscillator..........................................................................................................12-7 12.7 Sleep Operation ...........................................................................................................12-9 12.8 Resetting Timer1 Using a CCP Trigger Output ............................................................12-9 12.9 Resetting of Timer1 Register Pair (TMR1H:TMR1L)....................................................12-9 12.10 Timer1 Prescaler..........................................................................................................12-9 12.11 Initialization ................................................................................................................12-10 12.12 Design Tips ................................................................................................................12-12 12.13 Related Application Notes..........................................................................................12-13 12.14 Revision History .........................................................................................................12-14 PICmicro MID-RANGE MCU FAMILY 12.1 Introduction The Timer1 module is a 16-bit timer/counter consisting of two 8-bit registers (TMR1H and TMR1L) which are readable and writable. The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The Timer1 Interrupt, if enabled, is generated on overflow which is latched in the TMR1IF interrupt flag bit. This interrupt can be enabled/disabled by setting/clearing the TMR1IE interrupt enable bit. Timer1 can operate in one of three modes: * As a synchronous timer * As a synchronous counter * As an asynchronous counter The operating mode is determined by clock select bit, TMR1CS (T1CON<1>), and the synchronization bit, T1SYNC (Figure 12-1). In timer mode, Timer1 increments every instruction cycle. In counter mode, it increments on every rising edge of the external clock input on pin T1CKI. Timer1 can be turned on and off using theTMR1ON control bit (T1CON<0>). Timer1 also has an internal "reset input", which can be generated by a CCP module. Timer1 has the capability to operate off an external crystal. When the Timer1 oscillator is enabled (T1OSCEN is set), the T1OSI and T1OSO pins become inputs. That is, their corresponding TRIS values are ignored. Figure 12-1: Timer1 Block Diagram Set TMR1IF flag bit on Overflow CCP Special Trigger TMR1 TMR1H 0 CLR TMR1L 1 TMR1ON on/off T1OSO/ T1CKI T1OSI Synchronized clock input T1OSC T1SYNC 1 T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock Prescaler 1, 2, 4, 8 Synchronize det 0 2 T1CKPS1:T1CKPS0 TMR1CS SLEEP input Note 1: When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. This eliminates power drain. DS31012A-page 12-2 1997 Microchip Technology Inc. Section 12. Timer1 12.2 Control Register Register 12-1 shows the Timer1 control register. Register 12-1: U-0 -- bit 7 U-0 -- T1CON: Timer1 Control Register R/W-0 T1CKPS1 R/W-0 T1CKPS0 R/W-0 T1OSCEN R/W-0 T1SYNC bit 7:6 Unimplemented: Read as '0' bit 5:4 T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits R/W-0 TMR1CS R/W-0 TMR1ON bit 0 12 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value T1OSCEN: Timer1 Oscillator Enable bit 1 = Oscillator is enabled 0 = Oscillator is shut off. The oscillator inverter and feedback resistor are turned off to eliminate power drain bit 2 T1SYNC: Timer1 External Clock Input Synchronization Select bit When TMR1CS = 1: 1 = Do not synchronize external clock input 0 = Synchronize external clock input When TMR1CS = 0: This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1 TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin T1OSO/T1CKI (on the rising edge) 0 = Internal clock (FOSC/4) bit 0 TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31012A-page 12-3 Timer1 bit 3 PICmicro MID-RANGE MCU FAMILY 12.3 Timer1 Operation in Timer Mode Timer mode is selected by clearing the TMR1CS (T1CON<1>) bit. In this mode, the input clock to the timer is FOSC/4. The synchronize control bit, T1SYNC (T1CON<2>), has no effect since the internal clock is always synchronized. 12.4 Timer1 Operation in Synchronized Counter Mode Counter mode is selected by setting the TMR1CS bit. In this mode the timer increments on every rising edge of clock input on the T1OSI pin when the oscillator enable bit (T1OSCEN) is set, or the T1OSO/T1CKI pin when the T1OSCEN bit is cleared. If the T1SYNC bit is cleared, then the external clock input is synchronized with internal phase clocks. The synchronization is done after the prescaler stage. The prescaler is an asynchronous ripple-counter. In this configuration, during SLEEP mode, Timer1 will not increment even if the external clock is present, since the synchronization circuit is shut off. The prescaler however will continue to increment. 12.4.1 External Clock Input Timing for Synchronized Counter Mode When an external clock input is used for Timer1 in synchronized counter mode, it must meet certain requirements. The external clock requirement is due to internal phase clock (Tosc) synchronization. Also, there is a delay in the actual incrementing of TMR1 after synchronization. When the prescaler is 1:1, the external clock input is the same as the prescaler output. The synchronization of T1CKI with the internal phase clocks is accomplished by sampling the prescaler output on alternating Tosc clocks of the internal phase clocks. Therefore, it is necessary for the T1CKI pin to be high for at least 2Tosc (and a small RC delay) and low for at least 2Tosc (and a small RC delay). Refer to parameters 45, 46, and 47 in the "Electrical Specifications" section. When a prescaler other than 1:1 is used, the external clock input is divided by the asynchronous ripple-counter prescaler so that the prescaler output is symmetrical. In order for the external clock to meet the sampling requirement, the ripple-counter must be taken into account. Therefore, it is necessary for the T1CKI pin to have a period of at least 4Tosc (and a small RC delay) divided by the prescaler value. Another requirement on the T1CKI pin high and low time is that they do not violate the minimum pulse width requirements). Refer to parameters 40, 42, 45, 46, and 47 in the "Electrical Specifications" section. DS31012A-page 12-4 1997 Microchip Technology Inc. Section 12. Timer1 12.5 Timer1 Operation in Asynchronous Counter Mode If T1SYNC (T1CON<2>) is set, the external clock input is not synchronized. The timer continues to increment asynchronously to the internal phase clocks. The timer will continue to run during SLEEP and can generate an interrupt on overflow which will wake-up the processor. However, special precautions in software are needed to read/write the timer (Subsection 12.5.2 "Reading and Writing Timer1 in Asynchronous Counter Mode"). Since the counter can operate in sleep, Timer1 can be used to implement a true real-time clock. In asynchronous counter mode, Timer1 cannot be used as a time-base for capture or compare operations. 12.5.1 External Clock Input Timing with Unsynchronized Clock If the T1SYNC control bit is set, the timer will increment completely asynchronously. The input clock must meet certain minimum high time and low time requirements. Refer to the Device Data Sheet Electrical Specifications Section, timing parameters 45, 46, and 47. Reading and Writing Timer1 in Asynchronous Counter Mode Reading TMR1H or TMR1L while the timer is running from an external asynchronous clock, will guarantee a valid read (taken care of in hardware). However, the user should keep in mind that reading the 16-bit timer in two 8-bit values itself poses certain problems since the timer may overflow between the reads. For writes, it is recommended that the user simply stop the timer and write the desired values. A write contention may occur by writing to the timer registers while the register is incrementing. This may produce an unpredictable value in the timer register. Reading the 16-bit value requires some care, since two separate reads are required to read the entire 16-bits. Example 12-1 shows why this may not be a straight forward read of the 16-bit register. Example 12-1: Reading 16-bit Register Issues Sequence 1 Sequence 2 TMR1 Action 04FFh 0500h 0501h 0502h 1997 Microchip Technology Inc. READ TMR1L Store in TMPL READ TMR1H Store in TMPH TMPH:TMPL xxxxh xxFFh xxFFh 05FFh Action READ TMR1H Store in TMPH READ TMR1L Store in TMPL TMPH:TMPL xxxxh 04xxh 04xxh 0401h DS31012A-page 12-5 Timer1 12.5.2 12 PICmicro MID-RANGE MCU FAMILY Example 12-2 shows a routine to read the 16-bit timer value with experiencing the issues shown in Example 12-1. This is useful if the timer cannot be stopped. Example 12-2: Reading a 16-bit Free-Running Timer ; All interrupts are disabled MOVF TMR1H, W ; Read high byte MOVWF TMPH ; MOVF TMR1L, W ; Read low byte MOVWF TMPL ; MOVF TMR1H, W ; Read high byte SUBWF TMPH, W ; Sub 1st read with 2nd read BTFSC STATUS,Z ; Is result = 0 GOTO CONTINUE ; Good 16-bit read ; ; TMR1L may have rolled over between the read of the high and low bytes. ; Reading the high and low bytes now will read a good value. ; MOVF TMR1H, W ; Read high byte MOVWF TMPH ; MOVF TMR1L, W ; Read low byte MOVWF TMPL ; ; Re-enable the Interrupt (if required) CONTINUE ; Continue with your code Writing a 16-bit value to the 16-bit TMR1 register is straight forward. First the TMR1L register is cleared to ensure that there are many Timer1 clock/oscillator cycles before there is a rollover into the TMR1H register. The TMR1H register is then loaded, and finally the TMR1L register is loaded. Example 12-3 shows this: Example 12-3: Writing a 16-bit Free Running Timer ; All interrupts are disabled CLRF TMR1L ; Clear Low byte, Ensures no ; rollover into TMR1H MOVLW HI_BYTE ; Value to load into TMR1H MOVWF TMR1H, F ; Write High byte MOVLW LO_BYTE ; Value to load into TMR1L MOVWF TMR1H, F ; Write Low byte ; Re-enable the Interrupt (if required) CONTINUE ; Continue with your code DS31012A-page 12-6 1997 Microchip Technology Inc. Section 12. Timer1 12.6 Timer1 Oscillator A crystal oscillator circuit is built in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting the T1OSCEN control bit (T1CON<3>). The oscillator is a low power oscillator, rated up to 200 kHz operation. It will continue to run during SLEEP. It is primarily intended for a 32 kHz crystal, which is an ideal frequency for real-time keeping. Table 12-1 shows the capacitor selection for the Timer1 oscillator. The Timer1 oscillator is identical to the LP oscillator. The user must provide a software time delay to ensure proper oscillator start-up. Note: This allows the counter to operate (increment) when the device is in sleep mode, which allows Timer1 to be used as a real-time clock. 12 Table 12-1: Capacitor Selection for the Timer1 Oscillator Freq C1 C2 LP 32 kHz 100 kHz 200 kHz 33 pF 15 pF 15 pF 33 pF 15 pF 15 pF Crystals Tested: 32.768 kHz Epson C-001R32.768K-A 20 PPM 100 kHz Epson C-2 100.00 KC-P 20 PPM 200 kHz STD XTL 200.000 kHz 20 PPM Note 1: Higher capacitance increases the stability of oscillator but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 1997 Microchip Technology Inc. DS31012A-page 12-7 Timer1 Osc Type PICmicro MID-RANGE MCU FAMILY 12.6.1 Typical Application This feature is typically used in applications where real-time needs to be kept, but it is also desirable to have the lowest possible power consumption. The Timer1 oscillator allows the device to be placed in sleep, while the timer continues to increment. When Timer1 overflows the interrupt could wake-up the device so that the appropriate registers could be updated. Figure 12-2: Timer1 Application power-down detect 8 OSC1 4 VDD Backup Battery current sink PIC16CXXX 4 TMR1 T1OSI 32 kHz T1OSO DS31012A-page 12-8 4 4x4 Keypad VSS 1997 Microchip Technology Inc. Section 12. Timer1 12.7 Sleep Operation When Timer1 is configured for asynchronous operation, the TMR1 registers will continue to increment for each timer clock (or prescale multiple of clocks). When the TMR1 register overflows, the TMR1IF bit will get set, and if enabled generate an interrupt that will wake the processor from sleep mode. The Timer1 oscillator will add a delta current, due to the operation of this circuitry. That is, the power-down current will no longer only be the leakage current of the device, but also the active current of the Timer1 oscillator and other Timer1 circuitry. 12.8 Resetting Timer1 Using a CCP Trigger Output If a CCP module is configured in compare mode to generate a "special event trigger" (CCP1M3:CCP1M0 = 1011), this signal resets Timer1. Note: The special event trigger from the CCP module does not set interrupt flag bit TMR1IF. In the event that a write to Timer1 coincides with a special event trigger from the CCP module, the write will take precedence. In this mode of operation, the CCPRxH:CCPRxL register pair effectively becomes the period register for Timer1. 12.9 Resetting of Timer1 Register Pair (TMR1H:TMR1L) TMR1H and TMR1L registers are not reset on a POR or any other reset, only by the CCP special event triggers. T1CON register is reset to 00h on a Power-on Reset or a Brown-out Reset. In any other reset, the register is unaffected. 12.10 Timer1 Prescaler The prescaler counter is cleared on writes to the TMR1H or TMR1L registers. Table 12-2: Registers Associated with Timer1 as a Timer/Counter Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RBIE(2) T0IF INTF RBIF(2) (1) TMR1IF TMR1IE (1) Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module. Note 1: The placement of this bit is device dependent. 2: These bits may also be named GPIE and GPIF. INTCON PIR PIE TMR1L TMR1H T1CON Legend: GIE PEIE T0IE 1997 Microchip Technology Inc. INTE Value on: POR, BOR Value on all other resets 0000 000x 0 0 xxxx xxxx xxxx xxxx --00 0000 0000 000u 0 0 uuuu uuuu uuuu uuuu --uu uuuu DS31012A-page 12-9 Timer1 Timer1 must be configured for either timer or synchronized counter mode to take advantage of the special event trigger feature. If Timer1 is running in asynchronous counter mode, this reset operation may not work, and should not be used. 12 PICmicro MID-RANGE MCU FAMILY 12.11 Initialization Since Timer1 has a software programmable clock source, there are three examples to show the initialization of each mode. Example 12-4 shows the initialization for the internal clock source, Example 12-5 shows the initialization for the external clock source, and Example 12-6 shows the initialization of the external oscillator mode. Example 12-4: CLRF CLRF CLRF CLRF BSF CLRF BCF CLRF MOVLW MOVWF BSF Timer1 Initialization (Internal Clock Source) T1CON ; ; TMR1H ; TMR1L ; INTCON ; STATUS, RP0 ; PIE1 ; STATUS, RP0 ; PIR1 ; 0x30 ; T1CON ; T1CON, TMR1ON ; Stop Timer1, Internal Clock Source, T1 oscillator disabled, prescaler = 1:1 Clear Timer1 High byte register Clear Timer1 Low byte register Disable interrupts Bank1 Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags Internal Clock source with 1:8 prescaler Timer1 is stopped and T1 osc is disabled Timer1 starts to increment ; ; The Timer1 interrupt is disabled, do polling on the overflow bit ; T1_OVFL_WAIT BTFSS PIR1, TMR1IF GOTO T1_OVFL_WAIT ; ; Timer has overflowed ; BCF PIR1, TMR1IF Example 12-5: CLRF CLRF CLRF CLRF BSF CLRF BCF CLRF MOVLW MOVWF Timer1 Initialization (External Clock Source) T1CON ; ; TMR1H ; TMR1L ; INTCON ; STATUS, RP0 ; PIE1 ; STATUS, RP0 ; PIR1 ; 0x32 ; T1CON ; ; T1CON, TMR1ON ; Stop Timer1, Internal Clock Source, T1 oscillator disabled, prescaler = 1:1 Clear Timer1 High byte register Clear Timer1 Low byte register Disable interrupts Bank1 Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags External Clock source with 1:8 prescaler Clock source is synchronized to device Timer1 is stopped and T1 osc is disabled Timer1 starts to increment BSF ; ; The Timer1 interrupt is disabled, do polling on the overflow bit ; T1_OVFL_WAIT BTFSS PIR1, TMR1IF GOTO T1_OVFL_WAIT ; ; Timer has overflowed ; BCF PIR1, TMR1IF DS31012A-page 12-10 1997 Microchip Technology Inc. Section 12. Timer1 Example 12-6: CLRF CLRF CLRF CLRF BSF CLRF BCF CLRF MOVLW MOVWF BSF Timer1 Initialization (External Oscillator Clock Source) T1CON ; ; TMR1H ; TMR1L ; INTCON ; STATUS, RP0 ; PIE1 ; STATUS, RP0 ; PIR1 ; 0x3E ; T1CON ; ; ; T1CON, TMR1ON ; Stop Timer1, Internal Clock Source, T1 oscillator disabled, prescaler = 1:1 Clear Timer1 High byte register Clear Timer1 Low byte register Disable interrupts Bank1 Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags External Clock source with oscillator circuitry, 1:8 prescaler, Clock source is asynchronous to device Timer1 is stopped Timer1 starts to increment 1997 Microchip Technology Inc. DS31012A-page 12-11 Timer1 ; ; The Timer1 interrupt is disabled, do polling on the overflow bit ; T1_OVFL_WAIT BTFSS PIR1, TMR1IF GOTO T1_OVFL_WAIT ; ; Timer has overflowed ; BCF PIR1, TMR1IF 12 PICmicro MID-RANGE MCU FAMILY 12.12 Design Tips Question 1: Timer1 does not seem to be keeping accurate time. Answer 1: There are a few reasons that this could occur 1. 2. DS31012A-page 12-12 You should never write to Timer1, where that could cause the loss of time. In most cases that means you should not write to the TMR1L register, but if the conditions are ok, you may write to the TMR1H register. Normally you write to the TMR1H register if you want the Timer1 overflow interrupt to be sooner then the full 16-bit time-out. You should ensure the your layout uses good PCB layout techniques so that noise does not couple onto the Timer1 oscillator lines. 1997 Microchip Technology Inc. Section 12. Timer1 12.13 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Timer1 are: Title Application Note # Using Timer1 in Asynchronous Clock Mode AN580 Low Power Real Time Clock AN582 Yet another Clock using the PIC16C92X AN649 12 Timer1 1997 Microchip Technology Inc. DS31012A-page 12-13 PICmicro MID-RANGE MCU FAMILY 12.14 Revision History Revision A This is the initial released revision of the Timer1 module description. DS31012A-page 12-14 1997 Microchip Technology Inc. M Section 13. Timer2 HIGHLIGHTS This section of the manual contains the following major topics: 13.1 Introduction ..................................................................................................................13-2 13.2 Control Register ...........................................................................................................13-3 13.3 Timer Clock Source......................................................................................................13-4 13.4 Timer (TMR2) and Period (PR2) Registers..................................................................13-4 13.5 TMR2 Match Output.....................................................................................................13-4 13.6 Clearing the Timer2 Prescaler and Postscaler.............................................................13-4 13.7 Sleep Operation ...........................................................................................................13-4 13.8 Initialization ..................................................................................................................13-5 13.9 Design Tips ..................................................................................................................13-6 13.10 Related Application Notes............................................................................................13-7 13.11 Revision History ...........................................................................................................13-8 13 Timer2 1997 Microchip Technology Inc. DS31013A page 13-1 PICmicro MID-RANGE MCU FAMILY 13.1 Introduction Timer2 is an 8-bit timer with a prescaler, a postscaler, and a period register. Using the prescaler and postscaler at their maximum settings, the overflow time is the same as a 16-bit timer. Timer2 is the PWM time-base when the CCP module(s) is used in the PWM mode. Figure 13-1 shows a block diagram of Timer2. The postscaler counts the number of times that the TMR2 register matched the PR2 register. This can be useful in reducing the overhead of the interrupt service routine on the CPU performance. Figure 13-1: Timer2 Block Diagram Sets flag bit TMR2IF TMR2 output (1) FOSC/4 Prescaler 1:1, 1:4, 1:16 2 TMR2 reg Reset Comparator EQ Postscaler 1:1 to 1:16 T2CKPS1:T2CKPS0 PR2 reg 4 TOUTPS3:TOUTPS0 Note: DS31013A-page 13-2 TMR2 register output can be software selected by the SSP Module as a baud clock. 1997 Microchip Technology Inc. Section 13. Timer2 13.2 Control Register Register 13-1 shows the Timer2 control register. Register 13-1: T2CON: Timer2 Control Register U-0 -- bit 7 R/W-0 TOUTPS3 R/W-0 TOUTPS2 R/W-0 TOUTPS1 R/W-0 TOUTPS0 bit 7 Unimplemented: Read as '0' bit 6:3 TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits R/W-0 TMR2ON R/W-0 T2CKPS1 R/W-0 T2CKPS0 bit 0 0000 = 1:1 Postscale 0001 = 1:2 Postscale * * * 1111 = 1:16 Postscale bit 2 TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1:0 T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 13 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 Timer2 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31013A-page 13-3 PICmicro MID-RANGE MCU FAMILY 13.3 Timer Clock Source The Timer2 module has one source of input clock, the device clock (FOSC/4). A prescale option of 1:1, 1:4 or 1:16 is software selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). 13.4 Timer (TMR2) and Period (PR2) Registers The TMR2 register is readable and writable, and is cleared on all device resets. Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. TMR2 is cleared when a WDT, POR, MCLR, or a BOR reset occurs, while the PR2 register is set. Timer2 can be shut off (disabled from incrementing) by clearing the TMR2ON control bit (T2CON<2>). This minimizes the power consumption of the module. 13.5 TMR2 Match Output The match output of TMR2 goes to two sources: 1. 2. Timer2 Postscaler SSP Clock Input There are four bits which select the postscaler. This allows the postscaler a 1:1 to 1:16 scaling (inclusive). After the postscaler overflows, the TMR2 interrupt flag bit (TMR2IF) is set to indicate the Timer2 overflow. This is useful in reducing the software overhead of the Timer2 interrupt service routine, since it will only execute once every postscaler # of matches. The match output of TMR2 is also routed to the Synchronous Serial Port module, which may software select this as the clock source for the shift clock. 13.6 Clearing the Timer2 Prescaler and Postscaler The prescaler and postscaler counters are cleared when any of the following occurs: * a write to the TMR2 register * a write to the T2CON register Note: When T2CON is written TMR2 does not clear. * any device reset (Power-on Reset, MCLR reset, Watchdog Timer Reset, Brown-out Reset, or Parity Error Reset) 13.7 Sleep Operation During sleep, TMR2 will not increment. The prescaler will retain the last prescale count, ready for operation to resume after the device wakes from sleep. Table 13-1: Registers Associated with Timer2 Name Bit 7 Bit 6 Bit 5 Bit 4 INTCON GIE PEIE T0IE INTE Bit 3 Bit 2 Bit 1 Bit 0 RBIE T0IF INTF RBIF Value on: POR, BOR, PER 0000 000x 0 PIE TMR2IE (1) 0 TMR2 Timer2 module's register 0000 0000 T2CON -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 PR2 Timer2 Period Register 1111 1111 Legend: x = unknown, u = unchanged, - = unimplemented read as `0'. Shaded cells are not used by the Timer2 module. Note 1: The position of this bit is device dependent. PIR DS31013A-page 13-4 TMR2IF (1) Value on all other resets 0000 000u 0 0 0000 0000 -000 0000 1111 1111 1997 Microchip Technology Inc. Section 13. Timer2 13.8 Initialization Example 13-1 shows how to initialize the Timer2 module, including specifying the Timer2 prescaler and postscaler. Example 13-1: CLRF CLRF CLRF BSF CLRF BCF CLRF MOVLW MOVWF BSF Timer2 Initialization T2CON ; ; TMR2 ; INTCON ; STATUS, RP0 ; PIE1 ; STATUS, RP0 ; PIR1 ; 0x72 ; T2CON ; T2CON, TMR2ON ; Stop Timer2, Prescaler = 1:1, Postscaler = 1:1 Clear Timer2 register Disable interrupts Bank1 Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags Postscaler = 1:15, Prescaler = 1:16 Timer2 is off Timer2 starts to increment ; ; The Timer2 interrupt is disabled, do polling on the overflow bit ; T2_OVFL_WAIT BTFSS PIR1, TMR2IF ; Has TMR2 interrupt occurred? GOTO T2_OVFL_WAIT ; NO, continue loop ; ; Timer has overflowed ; BCF PIR1, TMR2IF ; YES, clear flag and continue. 13 Timer2 1997 Microchip Technology Inc. DS31013A-page 13-5 PICmicro MID-RANGE MCU FAMILY 13.9 Design Tips No related Design Tips at this time. DS31013A-page 13-6 1997 Microchip Technology Inc. Section 13. Timer2 13.10 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Timer2 Module are: Title Application Note # Using the CCP Module AN594 Air Flow Control using Fuzzy Logic AN600 Adaptive Differential Pulse Code Modulation using PICmicros AN643 13 Timer2 1997 Microchip Technology Inc. DS31013A-page 13-7 PICmicro MID-RANGE MCU FAMILY 13.11 Revision History Revision A This is the initial released revision of the TImer2 module description. DS31013A-page 13-8 1997 Microchip Technology Inc. M Section 14. Compare/Capture/PWM (CCP) HIGHLIGHTS This section of the manual contains the following major topics: 14.1 14.2 14.3 14.4 14.5 14.6 14.7 14.8 14.9 Introduction ..................................................................................................................14-2 Control Register ...........................................................................................................14-3 Capture Mode ..............................................................................................................14-4 Compare Mode ............................................................................................................14-6 PWM Mode ..................................................................................................................14-8 Initialization ................................................................................................................14-12 Design Tips ................................................................................................................14-15 Related Application Notes..........................................................................................14-17 Revision History .........................................................................................................14-18 14 CCP 1997 Microchip Technology Inc. DS31014A page 14-1 PICmicro MID-RANGE MCU FAMILY 14.1 Introduction Each CCP (Capture/Compare/PWM) module contains a 16-bit register which can operate as a 16-bit capture register, as a 16-bit compare register or as a 10-bit PWM master/slave Duty Cycle register. The CCP modules are identical in operation, with the exception of the operation of the special event trigger. Each CCP module has 3 registers. Multiple CCP modules may exist on a single device. Throughout this section we use generic names for the CCP registers. These generic names are shown in Table 14-1. Table 14-1: Specific to Generic CCP Nomenclature Generic Name CCPxCON CCPRxH CCPRxL CCPx CCP1 CCP2 CCP1CON CCPR1H CCPR1L CCP1 CCP2CON CCPR2H CCPR2L CCP2 Comment CCP control register CCP High byte CCP Low byte CCP pin Table 14-2 shows the resources of the CCP modules, in each of its modes. While Table 14-3 shows the interactions between the CCP modules, where CCPx is one CCP module and CCPy is another CCP module. Table 14-2: CCP Mode - Timer Resource CCP Mode Timer Resource Capture Compare PWM Timer1 Timer1 Timer2 Table 14-3: Interaction of Two CCP Modules CCPx Mode CCPy Mode DS31014A-page 14-2 Interaction Capture Capture Same TMR1 time-base. Capture Compare The compare should be configured for the special event trigger, which clears TMR1. Compare Compare The compare(s) should be configured for the special event trigger, which clears TMR1. PWM PWM The PWMs will have the same frequency, and update rate (TMR2 interrupt). PWM Capture None PWM Compare None 1997 Microchip Technology Inc. Section 14. CCP 14.2 Control Register Register 14-1: CCPxCON Register U-0 -- bit 7 U-0 -- R/W-0 DCxB1 R/W-0 DCxB0 bit 7:6 Unimplemented: Read as '0' bit 5:4 DCxB1:DCxB0: PWM Duty Cycle bit1 and bit0 Capture Mode: Unused R/W-0 R/W-0 R/W-0 CCPxM3 CCPxM2 CCPxM1 R/W-0 CCPxM0 bit 0 Compare Mode: Unused PWM Mode: These bits are the two LSbs (bit1 and bit0) of the 10-bit PWM duty cycle. The upper eight bits (DCx9:DCx2) of the duty cycle are found in CCPRxL. bit 3:0 CCPxM3:CCPxM0: CCPx Mode Select bits 0000 = 0100 = 0101 = 0110 = 0111 = 1000 = 1001 = 1010 = 1011 = 11xx = Capture/Compare/PWM off (resets CCPx module) Capture mode, every falling edge Capture mode, every rising edge Capture mode, every 4th rising edge Capture mode, every 16th rising edge Compare mode, Initialize CCP pin Low, on compare match force CCP pin High (CCPIF bit is set) Compare mode, Initialize CCP pin High, on compare match force CCP pin Low (CCPIF bit is set) Compare mode, Generate software interrupt on compare match (CCPIF bit is set, CCP pin is unaffected) Compare mode, Trigger special event (CCPIF bit is set) PWM mode 14 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset CCP 1997 Microchip Technology Inc. DS31014A-page 14-3 PICmicro MID-RANGE MCU FAMILY 14.3 Capture Mode In Capture mode, CCPRxH:CCPRxL captures the 16-bit value of the TMR1 register when an event occurs on pin CCPx. An event is defined as: * * * * Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge An event is selected by control bits CCPxM3:CCPxM0 (CCPxCON<3:0>). When a capture is made, the interrupt request flag bit, CCPxIF, is set. The CCPxIF bit must be cleared in software. If another capture occurs before the value in register CCPRx is read, the previous captured value will be lost. Note: Timer1 must be running in timer mode or synchronized counter mode for the CCP module to use the capture feature. In asynchronous counter mode, the capture operation may not work. As can be seen in Figure 14-1, a capture does not reset the 16-bit TMR1 register. This is so Timer1 can also be used as the timebase for other operations. The time between two captures can easily be computed as the difference between the value of the second capture that of the first capture. When Timer1 overflows, the TMR1IF bit will be set and if enabled an interrupt will occur, allowing the time base to be extended to greater than 16-bits. 14.3.1 CCP Pin Configuration In Capture mode, the CCPx pin should be configured as an input by setting its corresponding TRIS bit. Note: If the CCPx pin is configured as an output, a write to the port can cause a capture condition. Figure 14-1: Capture Mode Operation Block Diagram Set flag bit CCPxIF Prescaler / 1, 4, 16 CCPx Pin CCPRxH and edge detect CCPRxL Capture Enable TMR1H TMR1L CCPxCON<3:0> Q's The prescaler can be used to get a very fine average resolution on a constant input frequency. For example, if we have a stable input frequency and we set the prescaler to 1:16, then the total error for those 16 periods is 1 TCY. This gives an effective resolution of TCY/16, which at 20 MHz is 12.5 ns. This technique is only valid where the input frequency is "stable" over the 16 samples. Without using the prescaler (1:1), each sample would have a resolution of TCY. DS31014A-page 14-4 1997 Microchip Technology Inc. Section 14. CCP 14.3.2 Changing Between Capture Modes When the Capture mode is changed, a capture interrupt may be generated. The user should keep the CCPxIE bit clear to disable these interrupts and should clear the CCPxIF flag bit following any such change in operating mode. 14.3.2.1 CCP Prescaler There are four prescaler settings, specified by bits CCPxM3:CCPxM0. Whenever the CCP module is turned off, or the CCP module is not in capture mode, the prescaler counter is cleared. This means that any reset will clear the prescaler counter. Switching from one capture prescale setting to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore the first capture may be from a nonzero prescaler. Example 14-1 shows the recommended method for switching between capture prescale settings. This example also clears the prescaler counter and will not generate the interrupt. Example 14-1: Changing Between Capture Prescalers CLRF MOVLW CCP1CON NEW_CAPT_PS MOVWF CCP1CON ; Turn CCP module off ; Load the W reg with the new prescaler ; mode value and CCP ON ; Load CCP1CON with this value To clear the Capture prescaler count, the CCP module must be configured into any non-capture CCP mode (Compare, PWM, or CCP off modes). 14.3.3 Sleep Operation When the device is placed in sleep, Timer1 will not increment (since it is in synchronous mode), but the prescaler will continue to count events (not synchronized). When a specified capture event occurs, the CCPxIF bit will be set, but the capture register will not be updated. If the CCP interrupt is enabled, the device will wake-up from sleep. The value in the 16-bit TMR1 register is not transferred to the 16-bit capture register, but since the timer was not incrementing, this value should not have any meaning. Effectively, this allows the CCP pin to be used as another external interrupt. 14.3.4 Effects of a Reset The CCP module is off, and the value in the capture prescaler is forced to 0. 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-5 PICmicro MID-RANGE MCU FAMILY 14.4 Compare Mode In Compare mode, the 16-bit CCPRx register value is constantly compared against the TMR1 register pair value. When a match occurs, the CCPx pin is: * Driven High * Driven Low * Remains Unchanged The action on the pin is based on the value of control bits CCPxM3:CCPxM0 (CCPxCON<3:0>). At the same time, a compare interrupt is also generated. Note: Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. Figure 14-2: Compare Mode Operation Block Diagram Trigger Special Event Q CCPx Pin TRIS Output Enable DS31014A-page 14-6 S R Set flag bit CCPxIF Output Logic CCPRxH match CCPRxL Comparator TMR1H TMR1L CCPxCON<3:0> Mode Select 1997 Microchip Technology Inc. Section 14. CCP 14.4.1 CCP Pin Operation in Compare Mode The user must configure the CCPx pin as an output by clearing the appropriate TRIS bit. Note: Clearing the CCPxCON register will force the CCPx compare output latch to the default low level. This is not the Port I/O data latch. Selecting the compare output mode, forces the state of the CCP pin to the state that is opposite of the match state. So if the Compare mode is selected to force the output pin low on match, then the output will be forced high until the match occurs (or the mode is changed). 14.4.2 Software Interrupt Mode When generate Software Interrupt mode is chosen, the CCPx pin is not affected. Only a CCP interrupt is generated (if enabled). 14.4.3 Special Event Trigger In this mode, an internal hardware trigger is generated which may be used to initiate an action. The special event trigger output of CCPx resets the TMR1 register pair. This allows the CCPRx register to effectively be a 16-bit programmable period register for Timer1. For some devices, the special trigger output of the CCP module resets the TMR1 register pair, and starts an A/D conversion (if the A/D module is enabled). Note: 14.4.4 The special event trigger will not set the Timer1 interrupt flag bit, TMR1IF. Sleep Operation When the device is placed in sleep, Timer1 will not increment (since in synchronous mode), and the state of the module will not change. If the CCP pin is driving a value, it will continue to drive that value. When the device wakes-up, it will continue form this state. 14.4.5 Effects of a Reset The CCP module is off. 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-7 PICmicro MID-RANGE MCU FAMILY 14.5 PWM Mode In Pulse Width Modulation (PWM) mode, the CCPx pin produces up to a 10-bit resolution PWM output. Since the CCPx pin is multiplexed with the PORT data latch, the corresponding TRIS bit must be cleared to make the CCPx pin an output. Note: Clearing the CCPxCON register will force the CCPx PWM output latch to the default low level. This is not the port I/O data latch. Figure 14-3 shows a simplified block diagram of the CCP module in PWM mode. For a step by step procedure on how to set up the CCP module for PWM operation, see Subsection 14.5.3 "Set-up for PWM Operation." Figure 14-3: Simplified PWM Block Diagram CCPxCON<5:4> (DCxB1:DCxB0) Duty cycle registers CCPRxL (DCxB9:DCxB2) 10 CCPRxH (Slave) TRIS 10 R Comparator S 10 CCP Module TMR2 Q CCPx (Note 1) 8 Comparator Clear Timer, CCPx pin and latch the Duty Cycle 8 PR2 Timer2 Module Note 1: 8-bit timer is concatenated with 2-bit internal Q clock or 2 bits of the prescaler to create 10-bit time-base. A PWM output (Figure 14-4) has a time-base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period). Figure 14-4: PWM Output Duty Cycle = DCxB9:DCxB0 Period = PR2 + 1 TMR2 = PR2 + 1, TMR2 forced to 0h TMR2 = Duty Cycle TMR2 = PR2 + 1, TMR2 forced to 0h DS31014A-page 14-8 1997 Microchip Technology Inc. Section 14. CCP 14.5.1 PWM Period The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: PWM period = [(PR2) + 1] * 4 * TOSC * (TMR2 prescale value), specified in units of time PWM frequency (FPWM) is defined as 1 / [PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCPx pin is set (exception: if PWM duty cycle = 0%, the CCPx pin will not be set) * The PWM duty cycle is latched from CCPRxL into CCPRxH Note: 14.5.2 The Timer2 postscaler is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM Duty Cycle The PWM duty cycle is specified by writing to the CCPRxL register and to the DCxB1:DCxB0 (CCPxCON<5:4>) bits. Up to 10-bit resolution is available: the CCPRxL contains the eight MSbs and CCPxCON<5:4> contains the two LSbs. This 10-bit value is represented by DCxB9:DCxB0. The following equation is used to calculate the PWM duty cycle: PWM duty cycle = (DCxB9:DCxB0 bits value) * Tosc * (TMR2 prescale value), in units of time The DCxB9:DCxB0 bits can be written to at any time, but the duty cycle value is not latched into CCPRxH until after a match between PR2 and TMR2 occurs (which is the end of the current period). In PWM mode, CCPRxH is a read-only register. The CCPRxH register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. When CCPRxH and 2-bit latch match the value of TMR2 concatenated with the internal 2-bit Q clock (or two bits of the TMR2 prescaler), the CCPx pin is cleared. This is the end of the duty cycle. Maximum PWM resolution (bits) for a given PWM frequency: ( log = FOSC FPWM ) bits log(2) Note: If the PWM duty cycle value is longer than the PWM period, the CCPx pin will not be cleared. This allows a duty cycle of 100%. 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-9 PICmicro MID-RANGE MCU FAMILY 14.5.2.2 Minimum Resolution The minimum resolution (in time) of each bit of the PWM duty cycle depends on the prescaler of Timer2. Table 14-4: Minimum Duty Cycle Bit Time Prescaler Value T2CKPS1:T2CKPS0 Minimum Resolution (Time) 1 4 16 00 01 1x TOSC TCY 4 TCY Example 14-2: PWM Period and Duty Cycle Calculation Desired PWM frequency is 78.125 kHz, Fosc = 20 MHz TMR2 prescale = 1 1/78.125 kHz= [(PR2) + 1] * 4 * 1/20 MHz * 1 12.8 s = [(PR2) + 1] * 4 * 50 ns * 1 PR2 = 63 Find the maximum resolution of the duty cycle that can be used with a 78.125 kHz frequency and 20 MHz oscillator: 1/78.125 kHz= 2PWM RESOLUTION * 1/20 MHz * 1 12.8 s = 2PWM RESOLUTION * 50 ns * 1 256 = 2PWM RESOLUTION log(256) = (PWM Resolution) * log(2) 8.0 = PWM Resolution At most, an 8-bit resolution duty cycle can be obtained from a 78.125 kHz frequency and a 20 MHz oscillator, i.e., 0 DCxB9:DCxB0 255. Any value greater than 255 will result in a 100% duty cycle. In order to achieve higher resolution, the PWM frequency must be decreased. In order to achieve higher PWM frequency, the resolution must be decreased. Table 14-5 lists example PWM frequencies and resolutions for Fosc = 20 MHz. The TMR2 prescaler and PR2 values are also shown. Table 14-5: Example PWM Frequencies and Bit Resolutions at 20 MHz PWM Frequency Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) DS31014A-page 14-10 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz 16 4 1 1 1 1 0xFF 10 0xFF 10 0xFF 10 0x3F 8 0x1F 7 0x17 5.5 1997 Microchip Technology Inc. Section 14. CCP 14.5.3 Set-up for PWM Operation The following steps configure the CCP module for PWM operation: 1. 2. 3. 4. 5. 14.5.4 Establish the PWM period by writing to the PR2 register. Establish the PWM duty cycle by writing to the DCxB9:DCxB0 bits. Make the CCPx pin an output by clearing the appropriate TRIS bit. Establish the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP module for PWM operation. Sleep Operation When the device is placed in sleep, Timer2 will not increment, and the state of the module will not change. If the CCP pin is driving a value, it will continue to drive that value. When the device wakes-up, it will continue from this state. 14.5.5 Effects of a Reset The CCP module is off. 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-11 PICmicro MID-RANGE MCU FAMILY 14.6 Initialization The CCP module has three modes of operation. Example 14-3 shows the initialization of capture mode, Example 14-4 shows the initialization of compare mode, and Example 14-5 shows the initialization of PWM mode. Example 14-3: CLRF CLRF CLRF CLRF BSF BSF CLRF BCF CLRF MOVLW MOVWF BSF Capture Initialization CCP1CON TMR1H TMR1L INTCON STATUS, RP0 TRISC, CCP1 PIE1 STATUS, RP0 PIR1 0x06 CCP1CON T1CON, TMR1ON ; ; ; ; ; ; ; ; ; ; ; ; CCP Module is off Clear Timer1 High byte Clear Timer1 Low byte Disable interrupts and clear T0IF Bank1 Make CCP pin input Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags Capture mode, every 4th rising edge Timer1 starts to increment ; ; The CCP1 interrupt is disabled, ; do polling on the CCP Interrupt flag bit ; Capture_Event BTFSS PIR1, CCP1IF GOTO Capture_Event ; ; Capture has occurred ; BCF PIR1, CCP1IF ; This needs to be done before next compare DS31014A-page 14-12 1997 Microchip Technology Inc. Section 14. CCP Example 14-4: CLRF CLRF CLRF CLRF BSF BCF CLRF BCF CLRF MOVLW MOVWF BSF Compare Initialization CCP1CON TMR1H TMR1L INTCON STATUS, RP0 TRISC, CCP1 PIE1 STATUS, RP0 PIR1 0x08 CCP1CON T1CON, TMR1ON ; ; ; ; ; ; ; ; ; ; ; ; CCP Module is off Clear Timer1 High byte Clear Timer1 Low byte Disable interrupts and clear T0IF Bank1 Make CCP pin output if controlling state of pin Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags Compare mode, set CCP1 pin on match Timer1 starts to increment ; ; The CCP1 interrupt is disabled, ; do polling on the CCP Interrupt flag bit ; Compare_Event BTFSS PIR1, CCP1IF GOTO Compare_Event ; ; Compare has occurred ; BCF PIR1, CCP1IF ; This needs to be done before next compare 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-13 PICmicro MID-RANGE MCU FAMILY Example 14-5: CLRF CLRF MOVLW MOVWF MOVLW MOVWF CLRF BSF BCF CLRF BCF CLRF MOVLW MOVWF BSF PWM Initialization CCP1CON TMR2 0x7F PR2 0x1F CCPR1L INTCON STATUS, RP0 TRISC, PWM1 PIE1 STATUS, RP0 PIR1 0x2C CCP1CON T2CON, TMR2ON ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; CCP Module is off Clear Timer2 Duty Cycle is 25% of PWM Period Disable interrupts and clear T0IF Bank1 Make pin output Disable peripheral interrupts Bank0 Clear peripheral interrupts Flags PWM mode, 2 LSbs of Duty cycle = 10 Timer2 starts to increment ; ; The CCP1 interrupt is disabled, ; do polling on the TMR2 Interrupt flag bit ; PWM_Period_Match BTFSS PIR1, TMR2IF GOTO PWM_Period_Match ; ; Update this PWM period and the following PWM Duty cycle ; BCF PIR1, TMR2IF DS31014A-page 14-14 1997 Microchip Technology Inc. Section 14. CCP 14.7 Design Tips Question 1: What timers can I use for the capture and compare modes? Answer 1: The capture and compare modes are designed around Timer1, so no other timer can be used for these functions. This also means that if multiple CCP modules (in parts with more than one) are being used for a capture or compare function, they will share the same timer. Question 2: What timers can I use with the PWM mode? Answer 2: The PWM mode is designed around Timer2, so no other timer can be used for this function. (It is the only timer with a period register associated with it.) If multiple CCP modules (in parts with more than one) are doing PWM they will share the same timer, meaning they will have the same PWM period and frequency. Question 3: Can I use one CCP module to do capture (or compare) AND PWM at the same time, since they use different timers as their reference? Answer 3: The timers may be different, but other logic functions are shared. However you can switch from one mode to the other. For a device with two CCP modules, you can also have CCP1 set up for PWM and CCP2 set up for capture or compare (or vice versa) since they are two independent modules. Question 4: How does a reset affect the CCP module? Answer 4: Any reset will turn the CCP module off. See the section on resets to see reset values. Question 5: I am setting up the CCP1CON module for "Compare Mode, trigger special event" (1011) which resets TMR1. When a compare match occurs, will I have both the TMR1 and the CCP1 interrupts pending (TMR1IF is set, CCP1IF is set)? Answer 5: The CCP1IF flag will be set on the match condition. TMR1IF is set when Timer1 overflows, and the special trigger reset of Timer1 is not considered an overflow. However, if both the CCPR1L and CCPR1H registers are set at FFh, then an overflow occurs at the same time as the match, which will then set both CCP1IF and TMR1IF. Question 6: Answer 6: Timer2 always resets to zero when it equals PR2 and flag bit TMR2IF always gets set at this time. By putting FFh into PR2, you will get an interrupt on overflow at FFh, as you would with Timer0, for instance. Quite often it is desirable to have an event occur at a periodic rate, perhaps an interrupt driven event. Normally an initial value would be placed into the timer so that the overflow will occur at the desired time. This value would have to be placed back into the timer every time it overflowed to make the interrupts occur at the same desired rate. The benefit of Timer2 is that a value can be written to PR2 that will cause it to reset at your desired time interval. This means you do not have the housekeeping chore of reloading the timer every time it overflows, since PR2 maintains its value. 1997 Microchip Technology Inc. DS31014A-page 14-15 CCP How do I use Timer2 as a general purpose timer, with an interrupt flag on rollover? 14 PICmicro MID-RANGE MCU FAMILY Question 7: I am using a CCP module in PWM mode. The duty cycle being output is almost always 100%, even when my program writes a value like 7Fh to the duty cycle register, which should be 50%. What am I doing wrong? Answer 7: 1. 2. The value in CCPRxL is higher than PR2. This happens quite often when a user desires a fast PWM output frequency and will write a small value in the PR2. In this case, if a value of 7Eh were written to PR2, then a value 7Fh in CCPRxL will result in 100% duty cycle. If the TRIS bit corresponding to the CCP output pin you are using is configured as an input, the PWM output cannot drive the pin. In this case the pin would float and duty cycle may appear to be 0%, 100% or some other floating value. Question 8: I want to determine a signal frequency using the CCP module in capture mode to find the period. I am currently resetting Timer1 on the first edge, then using the value in the capture register on the second edge as the time period. The problem is that my code to clear the timer does not occur until almost twelve instructions after the first capture edge (interrupt latency plus saving of registers in interrupt) so I cannot measure very fast frequencies. Is there a better way to do this? Answer 8: You do not need to zero the counter to find the difference between two pulse edges. Just take the first captured value and put it into another set of registers. Then when the second capture event occurs, just subtract the first event from the second. Assuming that your pulse edges are not so far apart that the counter can wrap around past the last capture value, the answer will always be correct. This is illustrated by the following example: 1. 2. 3. First captured value is FFFEh. Store this value in two registers. The second capture value is 0001h (the counter has incremented three times). 0001h - FFFEh = 0003, which is the same as if you had cleared Timer1 to zero and let it count to 3. (Theoretically, except that there was a delay getting to the code that clears Timer1, so actual values would differ). The interrupt overhead is now less important because the values are captured automatically. For even faster inputs do not enable interrupts and just test the flag bit in a loop. If you must also capture very long time periods, such that the timer can wrap around past the previous capture value, then consider using an auto-scaling technique that starts with a large prescale and shorten the prescale as you converge on the exact frequency. DS31014A-page 14-16 1997 Microchip Technology Inc. Section 14. CCP 14.8 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the CCP modules are: Title Application Note # Using the CCP Modules AN594 Implementing Ultrasonic Ranging AN597 Air Flow Control Using Fuzzy Logic AN600 Adaptive Differential Pulse Code Modulation AN643 14 CCP 1997 Microchip Technology Inc. DS31014A-page 14-17 PICmicro MID-RANGE MCU FAMILY 14.9 Revision History Revision A This is the initial released revision of the CCP module description. DS31014A-page 14-18 1997 Microchip Technology Inc. M Section 15. Synchronous Serial Port (SSP) HIGHLIGHTS This section of the manual contains the following major topics: 15.1 15.2 15.3 15.4 15.5 15.6 15.7 15.8 Introduction ..................................................................................................................15-2 Control Registers .........................................................................................................15-3 SPI Mode .....................................................................................................................15-6 SSP I2C Operation .....................................................................................................15-16 Initialization ................................................................................................................15-26 Design Tips ................................................................................................................15-28 Related Application Notes..........................................................................................15-29 Revision History .........................................................................................................15-30 Note: Please refer to Appendix C.2 or the device data sheet to determine which devices use this module. 15 SSP I2C is a trademark of Philips Corporation. 1997 Microchip Technology Inc. DS31015A page 15-1 PICmicro MID-RANGE MCU FAMILY 15.1 Introduction The Synchronous Serial Port (SSP) module is a serial interface useful for communicating with other peripherals or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can operate in one of two modes: * Serial Peripheral Interface (SPITM) * Inter-Integrated Circuit (I 2CTM) - Slave mode - I/O slope control, and Start and Stop bit detection to ease software implementation of Master and Multi-master modes SPI is a registered trademark of Motorola Corporation. I2C is a trademark of Philips Corporation. DS31015A-page 15-2 1997 Microchip Technology Inc. Section 15. SSP 15.2 Control Registers Register 15-1: SSPSTAT: Synchronous Serial Port Status Register R/W-0 SMP bit 7 bit 7 R/W-0 CKE R-0 D/A R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0 SMP: SPI data input sample phase SPI Master Mode 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave Mode SMP must be cleared when SPI is used in slave mode bit 6 CKE: SPI Clock Edge Select (Figure 15-3, Figure 15-4, and Figure 15-5) CKP = 0 (SSPCON<4>) 1 = Data transmitted on rising edge of SCK 0 = Data transmitted on falling edge of SCK CKP = 1 (SSPCON<4>) 1 = Data transmitted on falling edge of SCK 0 = Data transmitted on rising edge of SCK bit 5 D/A: Data/Address bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address bit 4 P: Stop bit (I2C mode only. This bit is cleared when the SSP module is disabled) 1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET) 0 = Stop bit was not detected last bit 3 S: Start bit (I2C mode only. This bit is cleared when the SSP module is disabled) 1 = Indicates that a start bit has been detected last (this bit is '0' on RESET) 0 = Start bit was not detected last bit 2 R/W: Read/Write bit information (I2C mode only) This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next start bit, stop bit, or not ACK bit. 1 = Read 0 = Write bit 1 UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated bit 0 BF: Buffer Full Status bit Receive (SPI and I2C modes) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2C 15 mode only) 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty SSP Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31015A-page 15-3 PICmicro MID-RANGE MCU FAMILY Register 15-2: SSPCON: Synchronous Serial Port Control Register R/W-0 WCOL bit 7 R/W-0 SSPOV R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 bit 7 WCOL: Write Collision Detect bit bit 6 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit R/W-0 SSPM0 bit 0 In SPI mode: 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost and the SSPBUF is no longer updated. Overflow can only occur in slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master mode the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2C mode: bit 5 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don`t care" in transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow SSPEN: Synchronous Serial Port Enable bit In both modes, when enabled, these pins must be properly configured as input or output. In SPI mode: 1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins bit 4 In I2C mode: 1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit In SPI mode: 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level In I2C mode: SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch) (Used to ensure data setup time) DS31015A-page 15-4 1997 Microchip Technology Inc. Section 15. SSP Register 15-2: bit 3:0 SSPCON: Synchronous Serial Port Control Register (Cont'd) SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0000 = SPI master mode, clock = FOSC/4 0001 = SPI master mode, clock = FOSC/16 0010 = SPI master mode, clock = FOSC/64 0011 = SPI master mode, clock = TMR2 output/2 0100 = SPI slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin 0110 = I2C slave mode, 7-bit address 0111 = I2C slave mode, 10-bit address 1000 = Reserved 1001 = Reserved 1010 = Reserved 1011 = I2C firmware controlled master mode (slave idle) 1100 = Reserved 1101 = Reserved 1110 = I2C slave mode, 7-bit address with start and stop bit interrupts enabled 1111 = I2C slave mode, 10-bit address with start and stop bit interrupts enabled Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as '0' - n = Value at POR reset 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-5 PICmicro MID-RANGE MCU FAMILY 15.3 SPI Mode The SPI mode allows 8-bits of data to be synchronously transmitted and received simultaneously. All four modes of SPI are supported, as well as MicrowireTM (sample edge) when the SPI is in the master mode. To accomplish communication, typically three pins are used: * Serial Data Out (SDO) * Serial Data In (SDI) * Serial Clock (SCK) Additionally a fourth pin may be used when in a slave mode of operation: * Slave Select (SS) 15.3.1 Operation When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON register (SSPCON<5:0>) and SSPSTAT<7:6>. These control bits allow the following to be specified: * * * * * * * Master Mode (SCK is the clock output) Slave Mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Clock edge (output data on rising/falling edge of SCK) Data Input Sample Phase Clock Rate (Master mode only) Slave Select Mode (Slave mode only) Figure 15-1 shows the block diagram of the SSP module, when in SPI mode. Figure 15-1: SSP Block Diagram (SPI Mode) Internal data bus Read Write SSPBUF reg SSPSR reg SDI bit0 shift clock SDO SS Control Enable SS Edge Select 2 Clock Select SSPM3:SSPM0 4 Edge Select SCK TMR2 output 2 Prescaler TCY 4, 16, 64 TRIS bit of SCK pin DS31015A-page 15-6 1997 Microchip Technology Inc. Section 15. SSP The SSP consists of a transmit/receive Shift Register (SSPSR) and a buffer register (SSPBUF). The SSPSR shifts the data in and out of the device, MSb first. The SSPBUF holds the data that was written to the SSPSR, until the received data is ready. Once the 8-bits of data have been received, that byte is moved to the SSPBUF register. Then the buffer full detect bit, BF (SSPSTAT<0>), and interrupt flag bit, SSPIF, are set. This double buffering of the received data (SSPBUF) allows the next byte to start reception before reading the data that was just received. Any write to the SSPBUF register during transmission/reception of data will be ignored, and the write collision detect bit, WCOL (SSPCON<7>), will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. When the application software is expecting to receive valid data, the SSPBUF should be read before the next byte of data to transfer is written to the SSPBUF. Buffer full bit, BF (SSPSTAT<0>), indicates when SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. Generally the SSP Interrupt is used to determine when the transmission/reception has completed. The SSPBUF must be read and/or written. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. Example 15-1 shows the loading of the SSPBUF (SSPSR) for data transmission. The shaded instruction is only required if the received data is meaningful (some SPI applications are transmit only). Example 15-1: BCF BSF LOOP BTFSS GOTO BCF MOVF MOVWF MOVF MOVWF Loading the SSPBUF (SSPSR) Register STATUS, RP1 STATUS, RP0 SSPSTAT, BF LOOP STATUS, RP0 SSPBUF, W RXDATA TXDATA, W SSPBUF ;Specify Bank1 ; ;Has data been received (transmit complete)? ;No ;Specify Bank0 ;W reg = contents of SSPBUF ;Save in user RAM, if data is meaningful ;W reg = contents of TXDATA ;New data to xmit The SSPSR is not directly readable or writable, and can only be accessed from addressing the SSPBUF register. Additionally, the SSP status register (SSPSTAT) indicates the various status conditions. 15 SSP Microwire is a trademark of National Semiconductor. 1997 Microchip Technology Inc. DS31015A-page 15-7 PICmicro MID-RANGE MCU FAMILY 15.3.2 Enabling SPI I/O To enable the serial port the SSP Enable bit, SSPEN (SSPCON<5>), must be set. To reset or reconfigure SPI mode, clear the SSPEN bit which re-initializes the SSPCON register, and then set the SSPEN bit. This configures the SDI, SDO, SCK, and SS pins as serial port pins. For the pins to behave as the serial port function, they must have their data direction bits (in the TRIS register) appropriately programmed. That is: * * * * * SDI must have the TRIS bit set SDO must have the TRIS bit cleared SCK (Master mode) must have the TRIS bit cleared SCK (Slave mode) must have the TRIS bit set SS must have the TRIS bit set Any serial port function that is not desired may be overridden by programming the corresponding data direction (TRIS) register to the opposite value. An example would be in master mode where you are only sending data (to a display driver), then both SDI and SS could be used as general purpose outputs by clearing their corresponding TRIS register bits. DS31015A-page 15-8 1997 Microchip Technology Inc. Section 15. SSP 15.3.3 Typical Connection Figure 15-2 shows a typical connection between two microcontrollers. The master controller (Processor 1) initiates the data transfer by sending the SCK signal. Data is shifted out of both shift registers on their programmed clock edge, and latched on the edge of the clock specified by the SMP bit. Both processors should be programmed to same Clock Polarity (CKP), then both controllers would send and receive data at the same time. Whether the data is meaningful (or dummy data) depends on the application software. This leads to three scenarios for data transmission: * Master sends data -- Slave sends dummy data * Master sends data -- Slave sends data * Master sends dummy data -- Slave sends data Figure 15-2: SPI Master/Slave Connection SPI Master SSPM3:SSPM0 = 00xxb SPI Slave SSPM3:SSPM0 = 010xb SDO SDI Serial Input Buffer (SSPBUF) Serial Input Buffer (SSPBUF) SDI Shift Register (SSPSR) MSb SDO LSb Shift Register (SSPSR) MSb LSb Serial Clock SCK PROCESSOR 1 SCK PROCESSOR 2 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-9 PICmicro MID-RANGE MCU FAMILY 15.3.4 Master Operation The master can initiate the data transfer at any time because it controls the SCK. The master determines when the slave (Processor 2) is to broadcast data by the software protocol. In master mode the data is transmitted/received as soon as the SSPBUF register is written to. If the SPI is only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal received byte (interrupts and status bits appropriately set). This could be useful in receiver applications as a "line activity monitor" mode. The clock polarity is selected by appropriately programming bit CKP (SSPCON<4>). This then would give waveforms for SPI communication as shown in Figure 15-3, Figure 15-4, and Figure 15-5 where the MSb is transmitted first. In master mode, the SPI clock rate (bit rate) is user programmable to be one of the following: * * * * FOSC/4 (or TCY) FOSC/16 (or 4 * TCY) FOSC/64 (or 16 * TCY) Timer2 output/2 This allows a maximum data rate of 5 Mbps (at 20 MHz). Figure 15-3: SPI Mode Waveform, Master Mode Write to SSPBUF SCK (CKP = 0, CKE = 0) SCK (CKP = 1, CKE = 0) 4 clock modes SCK (CKP = 0, CKE = 1) SCK (CKP = 1, CKE = 1) SDO (CKE = 0) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDO (CKE = 1) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDI (SMP = 0) bit0 bit7 Input Sample (SMP = 0) SDI (SMP = 1) bit7 bit0 Input Sample (SMP = 1) SSPIF Next Q4 cycle after Q2 SSPSR to SSPBUF DS31015A-page 15-10 1997 Microchip Technology Inc. Section 15. SSP 15.3.5 Slave Operation In slave mode, the data is transmitted and received as the external clock pulses appear on SCK. When the last bit is latched, the interrupt flag bit SSPIF is set. The clock polarity is selected by appropriately programming bit CKP (SSPCON<4>). This then would give waveforms for SPI communication as shown in Figure 15-3, Figure 15-4, and Figure 15-5 where the MSb is transmitted first. When in slave mode the external clock must meet the minimum high and low times. In sleep mode, the slave can transmit and receive data. When a byte is received, the device will wake-up from sleep, if the interrupt is enabled. Figure 15-4: SPI Mode Waveform (Slave Mode With CKE = 0) SS optional SCK (CKP = 0, CKE = 0) SCK (CKP = 1, CKE = 0) Write to SSPBUF SDO SDI (SMP = 0) bit7 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 bit0 Input Sample (SMP = 0) SSPIF SSPSR to SSPBUF Next Q4 Cycle after Q2 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-11 PICmicro MID-RANGE MCU FAMILY 15.3.6 Slave Select Mode When in slave select mode, the SS pin allows multi-drop for multiple slaves with a single master. The SPI must be in slave mode (SSPCON<3:0> = 04h) and the TRIS bit, for the SS pin, must be set for the slave select mode to be enabled. When the SS pin is low, transmission and reception are enabled and the SDO pin is driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a transmitted byte, and becomes a floating output. External pull-up/ pull-down resistors may be desirable, depending on the application. When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> = 0100) the SPI module will reset if the SS pin is set to VDD. If the SPI is used in Slave Mode with the CKE bit is set, then the SS pin control must be enabled. When the SPI module resets, the bit counter is forced to 0. This can be done by either by forcing the SS pin to a high level or clearing the SSPEN bit (Figure 15-6). To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot create a bus conflict. Figure 15-5: SPI Mode Waveform (Slave Select Mode With CKE = 1) SS not optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSPBUF SDO SDI (SMP = 0) bit7 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 bit0 Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF DS31015A-page 15-12 Next Q4 cycle after Q2 1997 Microchip Technology Inc. Section 15. SSP Figure 15-6: Slave Synchronization Waveform SS SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPBUF SDO SDI (SMP = 0) bit7 bit6 bit7 bit0 bit0 bit7 bit7 Input Sample (SMP = 0) SSPIF Interrupt Flag SSPSR to SSPBUF 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-13 PICmicro MID-RANGE MCU FAMILY 15.3.7 Sleep Operation In master mode all module clocks are halted, and the transmission/reception will remain in that state until the device wakes from sleep. After the device returns to normal mode, the module will continue to transmit/receive data. In slave mode, the SPI transmit/receive shift register operates asynchronously to the device. This allows the device to be placed in sleep mode, and data to be shifted into the SPI transmit/receive shift register. When all 8-bits have been received, the SSP interrupt flag bit will be set and if enabled will wake the device from sleep. DS31015A-page 15-14 1997 Microchip Technology Inc. Section 15. SSP 15.3.8 Effects of a Reset A reset disables the SSP module and terminates the current transfer. Table 15-1: Registers Associated with SPI Operation Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets INTCON GIE PEIE T0IE INTE RBIE(2) T0IF INTF RBIF(2) 0000 000x 0000 000u 0 0 PIR PIE SSPIF (1) SSPIE (1) SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPCON WCOL SSPOV SSPEN TRISA TRISC SSPSTAT -- -- CKP SSPM3 SSPM2 SSPM1 SSPM0 PORTA Data Direction Register PORTC Data Direction Control Register SMP CKE D/A P S R/W UA BF 0 0 xxxx xxxx uuuu uuuu 0000 0000 0000 0000 --11 1111 --11 1111 1111 1111 1111 1111 0000 0000 0000 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in SPI mode. Note 1: The position of this bit is device dependent. 2: These bits may also be named GPIE and GPIF. 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-15 PICmicro MID-RANGE MCU FAMILY 15.4 SSP I 2C Operation The SSP module in I 2C mode fully implements all slave functions, except general call support, and provides interrupts on start and stop bits in hardware to facilitate software implementations of the master functions. The SSP module implements the standard mode specifications as well as 7-bit and 10-bit addressing. Appendix A gives an overview of the I 2C bus specification. Two pins are used for data transfer. These are the SCL pin, which is the clock, and the SDA pin, which is the data. The user must configure these pins as inputs through the TRIS bits. The SSP module functions are enabled by setting SSP Enable bit, SSPEN (SSPCON<5>). A "glitch" filter is on the SCL and SDA pins when the pin is an input. This filter operates in both the 100 KHz and 400 KHz modes. In the 100 KHz mode, when these pins are an output, there is a slew rate control of the pin that is independent of device frequency. Figure 15-7: SSP Block Diagram (I2C Mode) Internal data bus Read Write SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb Match detect Address Match SSPADD reg Start and Stop bit detect DS31015A-page 15-16 Set, Reset S, P bits (SSPSTAT reg) 1997 Microchip Technology Inc. Section 15. SSP The SSP module has five registers for I2C operation. They are: * * * * * SSP Control Register (SSPCON) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - Not directly accessible SSP Address Register (SSPADD) The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: * * * * * I 2C Slave mode (7-bit address) I 2C Slave mode (10-bit address) I 2C Firmware controlled Multi-Master mode (start and stop bit interrupts enabled) I 2C Firmware controlled Multi-Master mode (start and stop bit interrupts enabled) I 2C Firmware controlled Master mode, slave is idle Before selecting any I 2C mode, the SCL and SDA pins must be programmed to inputs by setting the appropriate TRIS bits. Selecting an I 2C mode, by setting the SSPEN bit, enables the SCL and SDA pins to be used as the clock and data lines in I 2C mode. The SSPSTAT register gives the status of the data transfer. This information includes detection of a START or STOP bit, specifies if the received byte was data or address, if the next byte is the completion of 10-bit address, and if this will be a read or write data transfer. The SSPBUF is the register to which transfer data is written to or read from. The SSPSR register shifts the data in or out of the device. In receive operations, the SSPBUF and SSPSR create a doubled buffered receiver. This allows reception of the next byte to begin before reading the last byte of received data. When the complete byte is received, it is transferred to the SSPBUF register and flag bit SSPIF is set. If another complete byte is received before the SSPBUF register is read, a receiver overflow has occurred and the SSPOV bit (SSPCON<6>) is set and the byte in the SSPSR is lost. The SSPADD register holds the slave address. In 10-bit mode, the user needs to write the high byte of the address (1111 0 A9 A8 0). Following the high byte address match, the low byte of the address needs to be loaded (A7:A0). 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-17 PICmicro MID-RANGE MCU FAMILY 15.4.1 Slave Mode In slave mode, the SCL and SDA pins must be configured as inputs (TRIS set). The SSP module will override the input state with the output data when required (slave-transmitter). When an address is matched or the data transfer after an address match is received, the hardware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF register with the received value currently in the SSPSR register. There are certain conditions that will cause the SSP module not to give this ACK pulse. These are if either (or both): a) b) The buffer full bit, BF (SSPSTAT<0>), was set before the message completed. The overflow bit, SSPOV (SSPCON<6>), was set before the message completed. In this case, the SSPSR register value is not loaded into the SSPBUF, but the SSPIF and SSPOV bits are set. Table 15-2 shows what happens when a data transfer byte is received, given the status of bits BF and SSPOV. The shaded cells show the condition where user software did not properly clear the overflow condition. Flag bit BF is cleared by reading the SSPBUF register while bit SSPOV is cleared through software. The SCL clock input must have a minimum high and low time for proper operation. The high and low times of the I2C specification as well as the requirement of the SSP module is shown in Device Data Sheet electrical specifications parameters 100 and 101. DS31015A-page 15-18 1997 Microchip Technology Inc. Section 15. SSP 15.4.1.1 Addressing Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, the 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register on the falling edge of the eight SCL pulse. The buffer full bit, BF, is set on the falling edge of the eigth SCL pulse. An ACK pulse is generated. SSP interrupt flag bit, SSPIF, is set (interrupt is generated if enabled) - on the falling edge of the ninth SCL pulse. In 10-bit address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. The R/W bit (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address the first byte would equal `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for a 10-bit address is as follows, with steps 7- 9 for slave-transmitter: 1. 2. 3. 4. 5. 6. 7. 8. 9. Receive first (high) byte of Address (the SSPIF, BF, and UA (SSPSTAT<1>) bits are set). Update the SSPADD register with second (low) byte of Address (clears the UA bit and releases the SCL line). Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Receive second (low) byte of Address (the SSPIF, BF, and UA bits are set). Update the SSPADD register with the high byte of Address. This will clear the UA bit and releases SCL line. Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Receive repeated START condition. Receive first (high) byte of Address (the SSPIF and BF bits are set). Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Note: Following the RESTART condition (step 7) in 10-bit mode, the user only needs to match the first 7-bit address. The user does not update the SSPADD for the second half of the address. Table 15-2: Data Transfer Received Byte Actions Status Bits as Data Transfer is Received BF SSPOV SSPSR SSPBUF 0 1 1 0 0 0 1 1 Yes No No Yes Set bit SSPIF Generate ACK (SSP Interrupt occurs Pulse if enabled) Yes No No No Yes Yes Yes Yes Note:Shaded cells show the conditions where the user software did not properly clear the overflow condition. 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-19 PICmicro MID-RANGE MCU FAMILY 15.4.1.2 Reception When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as either the BF bit (SSPSTAT<0>) is set or the SSPOV bit (SSPCON<6>) is set. So when a byte is received, with these conditions, and attempts to move from the SSPSR register to the SSPBUF register, no acknowledge pulse is given. An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software. The SSPSTAT register is used to determine the status of the receive byte. I 2C Waveforms for Reception (7-bit Address) Figure 15-8: Receiving Address Receiving Data R/W=0 Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDA SCL S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 SSPIF 9 P Bus Master terminates transfer BF (SSPSTAT<0>) Cleared in software SSPBUF register is read SSPOV (SSPCON<6>) Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent. DS31015A-page 15-20 1997 Microchip Technology Inc. UA (SSPSTAT<1>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 S SCL SSP 1997 Microchip Technology Inc. 1 2 1 4 3 5 0 6 A9 7 A8 8 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR 1 1 9 ACK R/W = 0 1 3 A5 4 A4 Cleared in software 2 A6 5 A3 6 A2 7 A1 8 A0 UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag A7 Receive Second Byte of Address 9 ACK 3 D5 4 D4 5 D3 Receive Data Byte Cleared in software 2 D6 Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag 1 D7 6 D2 7 D1 8 D0 9 ACK R/W = 1 Read of SSPBUF clears BF flag P Bus Master terminates transfer Figure 15-9: SDA Receive First Byte of Address Clock is held low until update of SSPADD has taken place Section 15. SSP I2C Waveforms for Reception (10-bit Address) 15 DS31015A-page 15-21 PICmicro MID-RANGE MCU FAMILY 15.4.1.3 Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit, and the SCL pin is held low. The transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit (SSPCON<4>). The master must monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 15-10). An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software, and the SSPSTAT register is used to determine the status of the byte transfer. The SSPIF flag bit is set on the falling edge of the ninth clock pulse. As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the not ACK is latched by the slave, the slave logic is reset and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit. Figure 15-10: I 2C Waveforms for Transmission (7-bit Address) Receiving Address SDA SCL A7 S A6 1 2 Data in sampled R/W = 1 A5 A4 A3 A2 A1 3 4 5 6 7 ACK 8 9 R/W = 0 ACK Transmitting Data D7 1 SCL held low while CPU responds to SSPIF D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 P SSPIF BF (SSPSTAT<0>) cleared in software SSPBUF is written in software From SSP interrupt service routine CKP (SSPCON<4>) Set bit after writing to SSPBUF (the SSPBUF must be written-to before the CKP bit can be set) DS31015A-page 15-22 1997 Microchip Technology Inc. UA (SSPSTAT<1>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 S 2 1 4 1 6 5 7 A9 A8 0 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR 3 1 8 9 ACK Receive First Byte of Address R/W = 0 SCL SSP 1997 Microchip Technology Inc. 1 1 3 4 5 Cleared in software 2 7 UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated. 6 A6 A5 A4 A3 A2 A1 8 A0 Receive Second Byte of Address Dummy read of SSPBUF to clear BF flag A7 9 ACK 2 3 1 4 1 Cleared in software 1 1 Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag Sr 1 5 0 6 7 A9 A8 Receive First Byte of Address 8 9 R/W=1 ACK 1 3 4 5 6 7 8 9 ACK P Write of SSPBUF initiates transmit Cleared in software Bus Master terminates transfer CKP has to be set for clock to be released 2 D4 D3 D2 D1 D0 Transmitting Data Byte D7 D6 D5 Master sends NACK Transmit is complete Figure 15-11: SDA Clock is held low until update of SSPADD has taken place Section 15. SSP I2C Waveforms for Transmission (10-bit Address) 15 DS31015A-page 15-23 PICmicro MID-RANGE MCU FAMILY 15.4.1.4 Clock Arbitration Clock arbitration has the SCL pin to inhibit the master device from sending the next clock pulse. The SSP module in I2C slave mode will hold the SCL pin low when the CPU needs to respond to the SSP interrupt (SSPIF bit is set and the CKP bit is cleared). The data that needs to be transmitted will need to be written to the SSPBUF register, and then the CKP bit will need to be set to allow the master to generate the required clocks. 15.4.2 Master Mode (Firmware) Master mode of operation is supported by interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle with both the S and P bits clear. In master mode the SCL and SDA lines are manipulated by clearing the corresponding TRIS bit(s). The output level is always low, irrespective of the value(s) in the PORT register. So when transmitting data, a '1' data bit must have it's TRIS bit set (input) and a '0' data bit must have it's TRIS bit cleared (output). The same scenario is true for the SCL line with the TRIS bit. The following events will cause SSP Interrupt Flag bit, SSPIF, to be set (SSP Interrupt if enabled): * START condition * STOP condition * Data transfer byte transmitted/received Master mode of operation can be done with either the slave mode idle (SSPM3:SSPM0 = 1011) or with the slave active (SSPM3:SSP0 = 1110 or 1111). When the slave modes are enabled, the software needs to differentiate the source(s) of the interrupt. 15.4.3 Multi-Master Mode (Firmware) In multi-Master mode, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit (SSPSTAT<4>) is set, or the bus is idle with both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. In Multi-Master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set the TRIS bits). There are two stages where this arbitration can be lost, they are: * Address transfer * Data transfer When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to retransfer the data at a later time. DS31015A-page 15-24 1997 Microchip Technology Inc. Section 15. SSP 15.4.4 Sleep Operation While in sleep mode, the I2C module can receive addresses or data, and when an address match or complete byte transfer occurs wake the processor from sleep (if the SSP interrupt is enabled). 15.4.5 Effect of a Reset A reset disables the SSP module and terminates the current transfer. Table 15-3: Registers Associated with I2C Operation Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets T0IF INTF RBIF(2) 0000 000x 0000 000u 0 0 PIE SSPIE (1) SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPADD Synchronous Serial Port (I2C mode) Address Register SSPCON WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 SSPSTAT SMP CKE D/A P S R/W UA BF Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by SSP in I2C mode. Note 1: The positions of these bits are device dependent. 2: These bits may also be named GPIE and GPIF. 0 xxxx xxxx 0000 0000 0000 0000 0000 0000 0 uuuu uuuu 0000 0000 0000 0000 0000 0000 Name Bit 7 Bit 6 Bit 5 Bit 4 INTCON GIE PEIE T0IE INTE RBIE(2) PIR Bit 3 SSPIF (1) 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-25 PICmicro MID-RANGE MCU FAMILY 15.5 Initialization Example 15-2: CLRF CLRF BSF MOVLW MOVWF BSF BSF BCF BSF MOVLW MOVWF DS31015A-page 15-26 SPI Master Mode Initialization STATUS ; SSPSTAT ; SSPSTAT, CKE ; 0x31 ; SSPCON ; ; STATUS, RP0 ; PIE, SSPIE ; STATUS, RP0 ; INTCON, GIE ; DataByte ; ; SSPBUF ; Bank 0 SMP = 0, CKE = 0, and clear status bits CKE = 1 Set up SPI port, Master mode, CLK/16, Data xmit on falling edge (CKE=1 & CKP=1) Data sampled in middle (SMP=0 & Master mode) Bank 1 Enable SSP interrupt Bank 0 Enable, enabled interrupts Data to be Transmitted Could move data from RAM location Start Transmission 1997 Microchip Technology Inc. Section 15. SSP 15.5.1 SSP Module / Basic SSP Module Compatibility When upgrading from the Basic SSP module, the SSPSTAT register contains two additional control bits. These bits are only used in SPI mode and are: * SMP, SPI data input sample phase * CKE, SPI Clock Edge Select To be compatible with the SPI of the Basic SSP module, these bits must be appropriately configured. If these bits are not at the states shown in Table 15-4, improper SPI communication may occur. Table 15-4: New Bit States for Compatibility Basic SSP Module SSP Module CKP CKP CKE SMP 1 0 1 0 0 0 0 0 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-27 PICmicro MID-RANGE MCU FAMILY 15.6 Design Tips Question 1: Using SPI mode, I do not seem able to talk to an SPI device. Answer 1: Ensure that you are using the correct SPI mode for that device. This SPI supports all four SPI modes so you should be able to get it to function. Check the clock polarity and the clock phase. Question 2: Using I2C mode, I do not seem able to make the master mode work. Answer 2: This SSP module does not have master mode fully automated in hardware, see Application Note AN578 for software which uses the SSP module to implement master mode. If you require a fully automated hardware implementation of I2C Master Mode, please refer to the Microchip Line Card for devices that have the Master SSP module. Note: At the time of printing only the High-end family of devices (PIC17CXXX) have devices with the Master SSP module implemented. Question 3: Using I2C mode, I write data to the SSPBUF register, but the data did not transmit. Answer 3: Ensure that you set the CKP bit to release the I2C clock. DS31015A-page 15-28 1997 Microchip Technology Inc. Section 15. SSP 15.7 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the SSP Module are: Title Application Note # Use of the SSP Module in the I 2C Multi-Master Environment. AN578 Using Microchip 93 Series Serial EEPROMs with Microcontroller SPI Ports Software Implementation of I2C Bus Master AN613 AN554 Use of the SSP module in the Multi-master Environment AN578 Interfacing PIC16C64/74 to Microchip SPI Serial EEPROM AN647 Interfacing a Microchip PIC16C92x to Microchip SPI Serial EEPROM AN668 15 SSP 1997 Microchip Technology Inc. DS31015A-page 15-29 PICmicro MID-RANGE MCU FAMILY 15.8 Revision History Revision A This is the initial released revision of the SSP module description. DS31015A-page 15-30 1997 Microchip Technology Inc. M 16 HIGHLIGHTS This section of the manual contains the following major topics: 16.1 16.2 16.3 16.4 16.5 16.6 16.7 16.8 Introduction ..................................................................................................................16-2 Control Registers .........................................................................................................16-3 SPITM Mode..................................................................................................................16-6 SSP I2C Operation .....................................................................................................16-15 Initialization ................................................................................................................16-23 Design Tips ................................................................................................................16-24 Related Application Notes..........................................................................................16-25 Revision History .........................................................................................................16-26 Note: Please refer to Appendix C.2 or the device data sheet to determine which devices use this module. SPI is a trademark of Motorola Corporation. I2C is a trademark of Philips Corporation. 1997 Microchip Technology Inc. DS31016A page 16-1 BSSP Section 16. Basic Sychronous Serial Port (BSSP) PICmicro MID-RANGE MCU FAMILY 16.1 Introduction The Basic Synchronous Serial Port (BSSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be Serial EEPROMs, shift registers, display drivers, A/D converters, etc. The BSSP module can operate in one of two modes: * Serial Peripheral Interface (SPITM) * Inter-Integrated Circuit (I 2CTM) - Slave mode - I/O slope control, Start and Stop bits to ease software implementation of Master and Multi-master modes I2C is a trademark of Philips Corporation. DS31016A-page 16-2 1997 Microchip Technology Inc. Section 16. BSSP 16.2 16 Control Registers Register 16-1: SSPSTAT: Synchronous Serial Port Status Register U-0 -- R-0 D/A bit 7:6 Unimplemented: Read as '0' bit 5 D/A: Data/Address bit (I2C mode only) R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address bit 4 P: Stop bit (I2C mode only. This bit is cleared when the SSP module is disabled) 1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET) 0 = Stop bit was not detected last bit 3 S: Start bit (I2C mode only. This bit is cleared when the SSP module is disabled) 1 = Indicates that a start bit has been detected last (this bit is '0' on RESET) 0 = Start bit was not detected last bit 2 R/W: Read/Write bit information (I2C mode only) This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next start bit, stop bit, or not ACK bit. 1 = Read 0 = Write bit 1 UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated bit 0 BF: Buffer Full Status bit Receive (SPI and I2C modes) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2C mode only) 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31016A-page 16-3 BSSP U-0 -- bit 7 PICmicro MID-RANGE MCU FAMILY Register 16-2: SSPCON: Synchronous Serial Port Control Register R/W-0 WCOL bit 7 R/W-0 SSPOV R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 bit 7 WCOL: Write Collision Detect bit bit 6 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit R/W-0 SSPM0 bit 0 In SPI mode: 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master mode the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2C mode: bit 5 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don`t care" in transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow SSPEN: Synchronous Serial Port Enable bit In both modes, when enabled, these pins must be properly configured as input or output. In SPI mode: 1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins bit 4 In I2C mode: 1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit In SPI mode: 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level In I2C mode: SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch) (Used to ensure data setup time) DS31016A-page 16-4 1997 Microchip Technology Inc. Section 16. BSSP Register 16-2: bit 3:0 16 SSPCON: Synchronous Serial Port Control Register (Cont'd) SSPM3:SSPM0: Synchronous Serial Port Mode Select bits Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31016A-page 16-5 BSSP 0000 = SPI master mode, clock = FOSC/4 0001 = SPI master mode, clock = FOSC/16 0010 = SPI master mode, clock = FOSC/64 0011 = SPI master mode, clock = TMR2 output/2 0100 = SPI slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin 0110 = I2C slave mode, 7-bit address 0111 = I2C slave mode, 10-bit address 1000 = Reserved 1001 = Reserved 1010 = Reserved 1011 = I2C Firmware controlled Master mode (slave idle) 1100 = Reserved 1101 = Reserved 1110 = I 2C Firmware controlled Multi-Master mode, 7-bit address with start and stop bit interrupts enabled 1111 = I 2C Firmware controlled Master mode, 10-bit address with start and stop bit interrupts enabled PICmicro MID-RANGE MCU FAMILY 16.3 SPITM Mode The SPI mode allows 8-bits of data to be synchronously transmitted and received simultaneously. To accomplish communication, typically three pins are used: * Serial Data Out (SDO) * Serial Data In (SDI) * Serial Clock (SCK) Additionally a fourth pin may be used when in a slave mode of operation: * Slave Select (SS) 16.3.1 Operation When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON register (SSPCON<5:0>). These control bits allow the following to be specified: * * * * * Master Mode (SCK is the clock output) Slave Mode (SCK is the clock input) Clock Polarity (Output/Input data on the Rising/Falling edge of SCK) Clock Rate (Master mode only) Slave Select Mode (Slave mode only) Figure 16-1 shows the block diagram of the SSP module, when in SPI mode. Figure 16-1: SSP Block Diagram (SPI Mode) Internal data bus Read Write SSPBUF reg SSPSR reg SDI bit0 shift clock SDO SS Control Enable SS Edge Select 2 Clock Select SSPM3:SSPM0 4 Edge Select SCK TMR2 output 2 Prescaler TCY 4, 16, 64 TRIS bit of SCK pin SPI is a trademark of Motorola Corporations. DS31016A-page 16-6 1997 Microchip Technology Inc. Section 16. BSSP Example 16-1: Loading the SSPBUF (SSPSR) Register BCF BSF LOOP BTFSS GOTO BCF MOVF MOVWF MOVF MOVWF STATUS, RP1 STATUS, RP0 SSPSTAT, BF LOOP STATUS, RP0 SSPBUF, W RXDATA TXDATA, W SSPBUF ;Specify Bank1 ; ;Has data been received (transmit complete)? ;No ;Specify Bank0 ;W reg = contents of SSPBUF ;Save in user RAM, if data is meaningful ;W reg = contents of TXDATA ;New data to xmit The SSPSR is not directly readable or writable, and can only be accessed from addressing the SSPBUF register. Additionally, the SSP status register (SSPSTAT) indicates the various status conditions. 1997 Microchip Technology Inc. DS31016A-page 16-7 16 BSSP The SSP consists of a transmit/receive Shift Register (SSPSR) and a Buffer register (SSPBUF). The SSPSR shifts the data in and out of the device, MSB first. The SSPBUF holds the data that was previously written to the SSPSR, until the received data is ready. Once the 8-bits of data have been received, that information is moved to the SSPBUF register. Then the buffer full detect bit, BF (SSPSTAT <0>), and interrupt flag bit, SSPIF, are set. This double buffering of the received data (SSPBUF) allows the next byte to start reception before reading the data that was received. Any write to the SSPBUF register during transmission/reception of data will be ignored, and the write collision detect bit, WCOL (SSPCON<7>), will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. When the application software is expecting to receive valid data, the SSPBUF should be read before the next byte of data to transfer is written to the SSPBUF. Buffer full bit, BF (SSPSTAT<0>), indicates when SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. Generally the SSP Interrupt is used to determine when the transmission/reception has completed. The SSPBUF can then be read (if data is meaningful) and/or the SSPBUF (SSPSR) can be written. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. Example 16-1 shows the loading of the SSPBUF (SSPSR) for data transmission. The shaded instruction is only required if the received data is meaningful (some SPI applications are transmit only). PICmicro MID-RANGE MCU FAMILY 16.3.2 Enabling SPI I/O To enable the serial port, SSP enable bit, SSPEN (SSPCON<5>), must be set. To reset or reconfigure SPI mode, clear the SSPEN bit which re-initializes the SSPCON register, and then set the SSPEN bit. This configures the SDI, SDO, SCK, and SS pins as serial port pins. For the pins to behave as the serial port function, they must have their data direction bits (in the TRIS register) appropriately programmed. That is: * * * * * SDI must have the TRIS bit set SDO must have the TRIS bit cleared SCK (Master mode) must have the TRIS bit cleared SCK (Slave mode) must have the TRIS bit set SS must have the TRIS bit set Any serial port function that is not desired may be overridden by programming the corresponding data direction (TRIS) register to the opposite value. An example would be in master mode where you are only sending data (to a display driver), then both SDI and SS could be used as general purpose outputs by clearing their corresponding TRIS register bits. DS31016A-page 16-8 1997 Microchip Technology Inc. Section 16. BSSP 16.3.3 16 Typical Connection * Master sends data -- Slave sends dummy data * Master sends data -- Slave sends data * Master sends dummy data -- Slave sends data Figure 16-2: SPI Master/Slave Connection SPI Master (SSPM3:SSPM0 = 00xxb) SPI Slave (SSPM3:SSPM0 = 010xb) SDO SDI Serial Input Buffer (SSPBUF) SDI Shift Register (SSPSR) MSb Serial Input Buffer (SSPBUF) LSb 1997 Microchip Technology Inc. Shift Register (SSPSR) MSb SCK PROCESSOR 1 SDO Serial Clock LSb SCK PROCESSOR 2 DS31016A-page 16-9 BSSP Figure 16-2 shows a typical connection between two microcontrollers. The master controller (Processor 1) initiates the data transfer by sending the SCK signal. Data is shifted out of both shift registers on their programmed clock edge, and latched on the opposite edge of the clock. Both processors should be programmed to same Clock Polarity (CKP), then both controllers would send and receive data at the same time. Whether the data is meaningful (or dummy data) depends on the application software. This leads to three scenarios for data transmission: PICmicro MID-RANGE MCU FAMILY 16.3.4 Master Operation The master can initiate the data transfer at any time because it controls the SCK. The master determines when the slave (Processor 2) wishes to broadcast data by the software protocol. In master mode the data is transmitted/received as soon as the SSPBUF register is written to. If the SPI is only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal received byte (interrupts and status bits appropriately set). This could be useful in receiver applications as a "line activity monitor" mode. The clock polarity is selected by appropriately programming the CKP bit (SSPCON<4>). This then would give waveforms for SPI communication as shown in Figure 16-5 and Figure 16-5 where the MSb is transmitted first. In master mode, the SPI clock rate (bit rate) is user programmable to be one of the following: * * * * FOSC/4 (or TCY) FOSC/16 (or 4 * TCY) FOSC/64 (or 16 * TCY) Timer2 output/2 This allows a maximum data rate of 5 Mbps (at 20 MHz). Figure 16-3: SPI Mode Waveform (Master Mode) SCK (CKP = 0) SCK (CKP = 1) SDO bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDI bit7 bit0 SSPIF Interrupt flag DS31016A-page 16-10 1997 Microchip Technology Inc. Section 16. BSSP 16.3.5 16 Slave Operation In slave mode, the data is transmitted and received as the external clock pulses appear on SCK. When the last bit is latched the SSPIF interrupt flag bit is set. In sleep mode, the slave can transmit and receive data and wake the device from sleep if the interrupt is enabled. Figure 16-4: SPI Mode Waveform (Slave Mode w/o SS Control) SCK (CKP = 0) SCK (CKP = 1) SDO bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDI bit7 bit0 SSPIF Interrupt flag Next Q4 Cycle after Q2 1997 Microchip Technology Inc. DS31016A-page 16-11 BSSP The clock polarity is selected by appropriately programming the CKP bit (SSPCON<4>). This then would give waveforms for SPI communication as shown in Figure 16-5 and Figure 16-5 where the MSb is transmitted first. When in slave mode the external clock must meet the minimum high and low times. PICmicro MID-RANGE MCU FAMILY 16.3.6 Slave Select Mode The SS pin allows a synchronous slave mode. The SPI must be in slave mode (SSPCON<3:0> = 04h) and the TRIS bit must be set the for the synchronous slave mode to be enabled. When the SS pin is low, transmission and reception are enabled and the SDO pin is driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a transmitted byte, and becomes a floating output. If the SS pin is taken low without resetting SPI mode, the transmission will continue from the point at which it was taken high. To clear the bit counter the Basic SSP module must be disabled and then re-enabled. External pull-up/pull-down resistors may be desirable, depending on the application. To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot create a bus conflict. Figure 16-5: SPI Mode Waveform (Slave Mode with ss Control) SS SCK (CKP = 0) SCK (CKP = 1) SDO bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDI bit7 bit0 SSPIF Next Q4 Cycle after Q2 DS31016A-page 16-12 1997 Microchip Technology Inc. Section 16. BSSP Figure 16-6: 16 Slave Synchronization Waveform SS BSSP SCK (CKP = 0) SCK (CKP = 1) Write to SSPBUF SDO SDI bit7 bit7 bit6 bit5 bit0 bit5 bit0 Input Sample SSPIF Interrupt Flag SSPSR to SSPBUF 1997 Microchip Technology Inc. DS31016A-page 16-13 PICmicro MID-RANGE MCU FAMILY 16.3.7 Sleep Operation In master mode all module clocks are halted, and the transmission/reception will remain in that state until the device wakes from sleep. After the device returns to normal mode, the module will continue to transmit/receive data. In slave mode, the SPI transmit/receive shift register operates asynchronously to the device. This allows the device to be placed in sleep mode, and data to be shifted into the SPI transmit/receive shift register. When all 8-bits have been received, the SSP interrupt flag bit will be set and if enabled will wake the device from sleep. 16.3.8 Effects of a Reset A reset disables the SSP module and terminates the current transfer. Table 16-1: Registers Associated with SPI Operation Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets INTCON GIE PEIE T0IE INTE RBIE(2) T0IF INTF RBIF(2) 0000 000x 0000 000u 0 0 PIR PIE SSPIF (1) SSPIE (1) SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPCON WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPSTAT -- -- D/A P S R/W UA 0 0 xxxx xxxx uuuu uuuu SSPM0 0000 0000 0000 0000 BF --00 0000 --00 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in SPI mode. Note 1: The position of this bit is device dependent. 2: These bits can also be named GPIE and GPIF. DS31016A-page 16-14 1997 Microchip Technology Inc. Section 16. BSSP 16.4 16 SSP I 2C Operation Two pins are used for data transfer. These are the SCL pin, which is the clock, and the SDA pin, which is the data. The user must configure these pins as inputs through the TRIS bits. The SSP module functions are enabled by setting SSP Enable bit, SSPEN (SSPCON<5>). A "glitch" filter is on the SCL and SDA pins when the pin is an input. This filter operates in both the 100 KHz and 400 KHz modes. In the 100 KHz mode, when these pins are an output, there is a slew rate control of the pin that is independent of device frequency. Figure 16-7: SSP Block Diagram (I2C Mode) Internal data bus Read Write SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb Match detect Addr Match SSPADD reg Start and Stop bit detect 1997 Microchip Technology Inc. Set, Reset S, P bits (SSPSTAT reg) DS31016A-page 16-15 BSSP The SSP module in I 2C mode fully implements all slave functions, except General Call Support, and provides interrupts on start and stop bits in hardware to facilitate software implementations of the master functions. The SSP module implements the standard and fast mode specifications as well as 7-bit and 10-bit addressing. Appendix A gives an overview of the I 2C bus specification. PICmicro MID-RANGE MCU FAMILY The SSP module has five registers for I2C operation. They are: * * * * * SSP Control Register (SSPCON) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - Not directly accessible SSP Address Register (SSPADD) The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: * I 2C Slave mode (7-bit address) * I 2C Slave mode (10-bit address) * I 2C Firmware controlled Multi-Master mode, 7-bit address (start and stop bit interrupts enabled) * I 2C Firmware controlled Multi-Master mode, 10-bit address (start and stop bit interrupts enabled) * I 2C Firmware controlled Master mode, slave is idle Before selecting any I 2C mode, the SCL and SDA pins must be programmed to inputs by setting the appropriate TRIS bits. Selecting an I 2C mode, by setting the SSPEN bit, enables the SCL and SDA pins to be used as the clock and data lines in I 2C mode. The SSPSTAT register gives the status of the data transfer. This information includes detection of a START or STOP bit, specifies if the received byte was data or address, if the next byte is the completion of 10-bit address, and if this will be a read or write data transfer. The SSPSTAT register is read only. The SSPBUF is the register to which transfer data is written to or read from. The SSPSR register shifts the data in or out of the device. In receive operations, the SSPBUF and SSPSR create a doubled buffered receiver. This allows reception of the next byte to begin before reading the last byte of received data. When the complete byte is received, it is transferred to the SSPBUF register and the SSPIF flag bit is set. If another complete byte is received before the SSPBUF register is read, a receiver overflow has occurred and bit SSPOV (SSPCON<6>) is set. The SSPADD register holds the slave address. In 10-bit mode, the user needs to write the high byte of the address (1111 0 A9 A8 0). Following the high byte address match, the low byte of the address needs to be loaded (A7:A0). DS31016A-page 16-16 1997 Microchip Technology Inc. Section 16. BSSP 16.4.1 16 Slave Mode In slave mode, the SCL and SDA pins must be configured as inputs (TRIS bits set). The SSP module will override the input state with the output data when required (slave-transmitter). There are certain conditions that will cause the SSP module not to give this ACK pulse. These are if either (or both): a) b) The buffer full bit, BF (SSPSTAT<0>), was set before the transfer was received. The overflow bit, SSPOV (SSPCON<6>), was set before the transfer was received. In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF and SSPOV bits are set. Table 16-2 shows what happens when a data transfer byte is received, given the status of the BF and SSPOV bits. The shaded cells show the condition where user software did not properly clear the overflow condition. The BF flag bit is cleared by reading the SSPBUF register while the SSPOV bit is cleared through software. The SCL clock input must have a minimum high and low time for proper operation. The high and low times of the I2C specification as well as the requirement of the SSP module are given in parameter 100 and parameter 101 of the "Electrical Specifications" section. 1997 Microchip Technology Inc. DS31016A-page 16-17 BSSP When an address is matched or the data transfer after an address match is received, the hardware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF register with the received value currently in the SSPSR register. PICmicro MID-RANGE MCU FAMILY 16.4.1.1 Addressing Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, the 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register on the falling edge of the eight SCL pulse. The buffer full bit, BF, is set on the falling edge of the eight SCL pulse. An ACK pulse is generated. SSP interrupt flag bit, SSPIF, is set (interrupt is generated if enabled) - on the falling edge of the ninth SCL pulse. In 10-bit address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. The R/W bit (SSPSTAT<2>) must specify a write, so the slave device will receive the second address byte. For a 10-bit address the first byte would equal `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for a 10-bit address is as follows, with steps 7- 9 for slave-transmitter: 1. 2. 3. 4. 5. 6. 7. 8. 9. Receive first (high) byte of Address (the SSPIF, BF, and UA (SSPSTAT<1>) bits are set). Update the SSPADD register with second (low) byte of Address (clears the UA bit and releases the SCL line). Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Receive second (low) byte of Address (the SSPIF, BF, and UA bits are set). Update the SSPADD register with the first (high) byte of Address. This will clear the UA bit and release the SCL line. Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Receive repeated START condition. Receive first (high) byte of Address (the SSPIF and BF bits are set). Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Note: Following the RESTART condition (step 7) in 10-bit mode, the user only needs to match the first 7-bit address. The user does not update the SSPADD for the second half of the address. Table 16-2: Data Transfer Received Byte Actions Status bits as data transfer is received BF SSPOV SSPSR SSPBUF 0 1 1 0 0 0 1 1 Yes No No Yes Set bit SSPIF (SSP Interrupt occurs Generate ACK if enabled) pulse Yes No No No Yes Yes Yes Yes Note:Shaded cells show the conditions where the user software did not properly clear the overflow condition DS31016A-page 16-18 1997 Microchip Technology Inc. Section 16. BSSP 16.4.1.2 16 Reception When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software, and the SSPSTAT register is used to determine the status of the byte. Figure 16-8: Receiving Address Receiving Data R/W=0 Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDA SCL I 2C Waveforms for Reception (7-bit Address) S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 SSPIF 9 P Bus Master terminates transfer BF (SSPSTAT<0>) Cleared in software SSPBUF register is read SSPOV (SSPCON<6>) Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent. 1997 Microchip Technology Inc. DS31016A-page 16-19 BSSP When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as either the BF bit (SSPSTAT<0>) is set or the SSPOV bit (SSPCON<6>) is set. PICmicro MID-RANGE MCU FAMILY 16.4.1.3 Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit, and the SCL pin is held low. The transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit (SSPCON<4>). The master must monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 16-9). An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software, and the SSPSTAT register is used to determine the status of the byte transfer. The SSPIF flag bit is set on the falling edge of the ninth clock pulse. As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the not ACK is latched by the slave, the slave logic is reset and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit. Figure 16-9: I 2C Waveforms for Transmission (7-bit Address) Receiving Address SDA SCL A7 A6 1 2 Data in sampled S R/W = 1 A5 A4 A3 A2 A1 3 4 5 6 7 Transmitting Data ACK 8 9 D7 1 SCL held low while CPU responds to SSPIF ACK D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 P SSPIF BF (SSPSTAT<0>) cleared in software SSPBUF is written in software From SSP interrupt service routine CKP (SSPCON<4>) Set bit after writing to SSPBUF 16.4.1.4 Clock Arbitration Clock arbitration has the SCL pin to inhibit the master device from sending the next clock pulse. The SSP module in I2C slave mode will hold the SCL pin low when the CPU needs to respond to the SSP interrupt (SSPIF bit is set and the CKP bit is cleared). The data that needs to be transmitted will need to be written to the SSPBUF register, and then the CKP bit will need to be set to allow the master to generate the required clocks. DS31016A-page 16-20 1997 Microchip Technology Inc. Section 16. BSSP 16.4.2 16 Master Mode (Firmware) In master mode the SCL and SDA lines are manipulated by clearing the corresponding TRIS bit(s). The output level is always low, irrespective of the value(s) in PORT. So when transmitting data, a '1' data bit must have the TRIS bit set (input) and a '0' data bit must have the TRIS bit cleared (output). The same scenario is true for the SCL line with the TRIS bit. The following events will cause the SSPIF Interrupt Flag bit to be set (SSP Interrupt if enabled): * START condition * STOP condition * Data transfer byte transmitted/received Master mode of operation can be done with either the slave mode idle (SSPM3:SSPM0 = 1011) or with the slave active (SSPM3:SSP0 = 1110 or 1111). When the slave modes are enabled, the software needs to differentiate the source(s) of the interrupt. 16.4.3 Multi-Master Mode (Firmware) In multi-master mode, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit (SSPSTAT<4>) is set, or the bus is idle with both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. In multi-master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set the TRIS bits). There are two stages where this arbitration can be lost, they are: * Address Transfer * Data Transfer When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at a later time. 1997 Microchip Technology Inc. DS31016A-page 16-21 BSSP Master mode of operation is supported by interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle with both the S and P bits clear. PICmicro MID-RANGE MCU FAMILY 16.4.4 Sleep Operation While in sleep mode, the I2C module can receive addresses or data, and when an address match or complete byte transfer occurs wake the processor from sleep (if the SSP interrupt is enabled). 16.4.5 Effect of a Reset A reset disables the SSP module and terminates the current transfer. Table 16-3: Registers Associated with I2C Operation Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets INTCON GIE PEIE T0IE INTE RBIE(2) T0IF INTF RBIF(2) PIR SSPIF 0000 000x 0000 000u (1) 0 0 (1) 0 xxxx xxxx 0000 0000 0000 0000 --00 0000 0 uuuu uuuu 0000 0000 0000 0000 --00 0000 PIE SSPIE SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPADD Synchronous Serial Port (I2C mode) Address Register SSPCON WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPSTAT -- -- D/A P S R/W UA Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by SSP in I2C mode. Note 1: The position of these bits is device dependent. 2: These bits can also be named GPIE and GPIF. DS31016A-page 16-22 SSPM0 BF 1997 Microchip Technology Inc. Section 16. BSSP 16.5 16 Initialization Example 16-2: SPI Master Mode Initialization STATUS SSPSTAT 0x31 SSPCON BSF BSF BCF BSF MOVLW STATUS, RP0 PIE1, SSPIE STATUS, RP0 INTCON, GIE DataByte MOVWF SSPBUF ; ; ; ; ; ; Bank 0 Clear status bits Set up SPI port, Master mode, CLK/16, Data xmit on rising edge Data sampled in middle Bank 1 ; Enable SSP interrupt ; Bank 0 ; Enable, enabled interrupts ; Data to be Transmitted ; Could move data from RAM location ; Start Transmission SSP Module / Basic SSP Module Compatibility When changing from the SSP Module to the Basic SSP module, the SSPSTAT register contains two additional control bits. These bits are: * SMP, SPI data input sample phase * CKE, SPI Clock Edge Select To be compatible with the SPI of the Basic SSP module, these bits must be appropriately configured. If these bits are not at the states shown in Table 16-4, improper SPI communication should be expected. If the SSP module uses a different configuration then shown in Table 16-4, the Basic SSP module can not be used to implement that mode. That mode may be implemented in software. Table 16-4: New Bit States for Compatibility Basic SSP Module 1997 Microchip Technology Inc. SSP Module CKP CKP CKE SMP 1 0 1 0 0 0 0 0 DS31016A-page 16-23 BSSP 16.5.1 CLRF CLRF MOVLW MOVWF PICmicro MID-RANGE MCU FAMILY 16.6 Design Tips Question 1: Using SPI mode, I do not seem able to talk to an SPI device. Answer 1: Ensure that you are using the correct SPI mode for that device. This SPI supports two of the four SPI modes so ensure that the SPI device that you are trying to interface to is compatible with one of these two modes. Check the clock polarity and the clock phase. If the device is not compatible, switch to one of the Microchip devices that has the SSP module, and that should solve this. Question 2: Using I2C mode, I do not seem able to make the master mode work. Answer 2: This SSP module does not have master mode fully automated in hardware, see Application Note AN578 for software which uses the SSP module to implement master mode. If you require a fully automated Hardware implementation of I2C master mode, please refer to the Microchip Line Card for devices that have the Master SSP module. Note: At the time of printing only the High-end family of devices (PIC17CXXX) have devices with the Master SSP module implemented. Question 3: Using I2C mode, I write data to the SSPBUF register, but the data did not transmit. Answer 3: Ensure that you set the CKP bit to release the I2C clock. DS31016A-page 16-24 1997 Microchip Technology Inc. Section 16. BSSP 16.7 16 Related Application Notes Title Application Note # Use of the SSP Module in the I 2C Multi-Master Environment. AN578 Using Microchip 93 Series Serial EEPROMs with Microcontroller SPI Ports Software Implementation of I2C Bus Master AN613 AN554 Use of the SSP module in the Multi-Master Environment AN578 Interfacing PIC16C64/74 to Microchip SPI Serial EEPROM AN647 Interfacing a Microchip PIC16C92x to Microchip SPI Serial EEPROM AN668 1997 Microchip Technology Inc. DS31016A-page 16-25 BSSP This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to this section are: PICmicro MID-RANGE MCU FAMILY 16.8 Revision History Revision A This is the initial revision of the Basic SSP module description. DS31016A-page 16-26 1997 Microchip Technology Inc. M Section 17. Master Synchronous Serial Port (MSSP) HIGHLIGHTS This section of the manual contains the following major topics: Introduction ..................................................................................................................17-2 Control Register ...........................................................................................................17-4 SPI Mode .....................................................................................................................17-9 SSP I2CTM Operation .................................................................................................17-18 Connection Considerations for I2C Bus .....................................................................17-56 Initialization ................................................................................................................17-57 Design Tips ................................................................................................................17-58 Related Application Notes..........................................................................................17-59 Revision History .........................................................................................................17-60 Note: At present NO Mid-Range MCU devices are available with this module. Devices are planned, but there is no schedule for availability. Please refer to Microchip's Web site or BBS for release of Product Briefs. You will be able to find out the details and the features for new devices. This module is available on Microchip's High End family (PIC17CXXX). Please refer to Microchip's Web site, BBS, Regional Sales Office, or Factory Representatives. I2C is a trademark of Philips Corporation. 1997 Microchip Technology Inc. Preliminary DS31017A page 17-1 MSSP 17.1 17.2 17.3 17.4 17.5 17.6 17.7 17.8 17.9 17 PICmicro MID-RANGE MCU FAMILY 17.1 Introduction The Master Synchronous Serial Port (MSSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be serial EEPROMs, shift registers, display drivers, A/D converters, etc. The MSSP module can operate in one of two modes: * Serial Peripheral Interface (SPITM) * Inter-Integrated Circuit (I 2CTM) - Full Master Mode - Slave mode (with general address call) Figure 17-1 shows a block diagram for the SPI mode, while Figure 17-2, and Figure 17-3 show the block diagrams for the two different I2C modes of operation. Figure 17-1: SPI Mode Block Diagram Internal data bus Read Write SSPBUF reg SSPSR reg SDI bit0 shift clock SDO SS Control Enable SS Edge Select 2 Clock Select SCK SSPM3:SSPM0 SMP:CKE 4 TMR2 output 2 2 Edge Select Prescaler TOSC 4, 16, 64 Data to TX/RX in SSPSR TRIS bit SPI is a trademark of Motorola Corporation. I2C is a trademark of Philips Corporation. DS31017A-page 17-2 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-2: I2C Slave Mode Block Diagram Internal data bus Read Write SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb 17 Address Match or General Call Detected Match detect Set, Reset S, P bits (SSPSTAT reg) Start and Stop bit detect Figure 17-3: MSSP SSPADD reg I2C Master Mode Block Diagram Internal data bus Read SSPADD<6:0> 7 Write Baud Rate Generator SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb Match detect Address Match or General Call Detected SSPADD reg Start and Stop bit detect / generate 1997 Microchip Technology Inc. Preliminary Set/Clear S bit and Clear/Set P bit (SSPSTAT reg) and Set SSPIF DS31017A-page 17-3 PICmicro MID-RANGE MCU FAMILY 17.2 Control Register Register 17-1: R/W-0 SMP bit 7 bit 7 SSPSTAT: SSP Status Register R/W-0 CKE R-0 D/A R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0 SMP: Sample bit SPI Master Mode 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave Mode SMP must be cleared when SPI is used in slave mode In I2C master or slave mode: bit 6 1= Slew rate control disabled for standard speed mode (100 kHz and 1 MHz) 0= Slew rate control enabled for high speed mode (400 kHz) CKE: SPI Clock Edge Select CKP = 0 1 = Data transmitted on rising edge of SCK 0 = Data transmitted on falling edge of SCK bit 5 bit 4 bit 3 bit 2 CKP = 1 1 = Data transmitted on falling edge of SCK 0 = Data transmitted on rising edge of SCK D/A: Data/Address bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address P: Stop bit (I2C mode only. This bit is cleared when the SSP module is disabled, SSPEN is cleared) 1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET) 0 = Stop bit was not detected last S: Start bit (I2C mode only. This bit is cleared when the SSP module is disabled, SSPEN is cleared) 1 = Indicates that a start bit has been detected last (this bit is '0' on RESET) 0 = Start bit was not detected last R/W: Read/Write bit information (I2C mode only) This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next start bit, stop bit, or not ACK bit. In I2C slave mode: 1 = Read 0 = Write bit 1 In I2C master mode: 1 = Transmit is in progress 0 = Transmit is not in progress. Or'ing this bit with SEN, RSEN, PEN, RCEN, or ACKEN will indicate if the SSP is in IDLE mode. UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated DS31017A-page 17-4 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Register 17-1: bit 0 SSPSTAT: SSP Status Register (Cont'd) BF: Buffer Full Status bit Receive (SPI and I2C modes) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2C mode only) 1 = Data Transmit in progress (does not include the ACK and stop bits), SSPBUF is full 0 = Data Transmit complete (does not include the ACK and stop bits), SSPBUF is empty Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 17 - n = Value at POR reset MSSP 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-5 PICmicro MID-RANGE MCU FAMILY Register 17-2: SSPCON1: SSP Control Register1 R/W-0 WCOL bit 7 bit 7 R/W-0 SSPOV R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 R/W-0 SSPM0 bit 0 WCOL: Write Collision Detect bit Master Mode: 1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a transmission to be started 0 = No collision bit 6 Slave Mode: 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit In SPI mode: 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in slave mode. In slave mode, the user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master mode the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2C mode: 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don't care" in transmit mode. SSPOV must be cleared in software in either mode. (must be cleared in software) bit 5 0 = No overflow SSPEN: Synchronous Serial Port Enable bit In both modes, when enabled, these pins must be properly configured as input or output. In SPI mode: 1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins bit 4 In I2C mode: 1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit In SPI mode: 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level In I2C slave mode: SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch) (Used to ensure data setup time) In I2C master mode Unused in this mode DS31017A-page 17-6 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Register 17-2: SSPCON1: SSP Control Register1 (Cont'd) bit 3 - 0 SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0000 = SPI master mode, clock = FOSC/4 0001 = SPI master mode, clock = FOSC/16 0010 = SPI master mode, clock = FOSC/64 0011 = SPI master mode, clock = TMR2 output/2 0100 = SPI slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin 0110 = I2C slave mode, 7-bit address 0111 = I2C slave mode, 10-bit address 1000 = I2C master mode, clock = FOSC / (4 * (SSPADD+1) ) 1xx1 = Reserved 1x1x = Reserved 1997 Microchip Technology Inc. Preliminary MSSP Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 17 - n = Value at POR reset DS31017A-page 17-7 PICmicro MID-RANGE MCU FAMILY Register 17-3: SSPCON2: SSP Control Register2 R/W-0 GCEN bit 7 bit 7 bit 6 bit 5 bit 4 R/W-0 ACKSTAT R/W-0 ACKDT R/W-0 ACKEN R/W-0 RCEN R/W-0 PEN R/W-0 RSEN R/W-0 SEN bit 0 GCEN: General Call Enable bit (In I2C slave mode only) 1 = Enable interrupt when a general call address (0000h) is received in the SSPSR 0 = General call address disabled ACKSTAT: Acknowledge Status bit (In I2C master mode only) In master transmit mode: 1 = Acknowledge was not received from slave 0 = Acknowledge was received from slave ACKDT: Acknowledge Data bit (In I2C master mode only) In master receive mode: Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive. 1 = Not Acknowledge 0 = Acknowledge ACKEN: Acknowledge Sequence Enable bit (In I2C master mode only) In master receive mode: 1 = Initiate Acknowledge sequence on SDA and SCL pins, and transmit AKDT data bit. Automatically cleared by hardware. 0 = Acknowledge sequence idle bit 3 If the I2C module is not in the idle mode, this bit may not be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled). RCEN: Receive Enable bit (In I2C master mode only) 1 = Enables Receive mode for I2C 0 = Receive idle bit 2 If the I2C module is not in the idle mode, this bit may not be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled). PEN: Stop Condition Enable bit (In I2C master mode only) SCK release control 1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Stop condition idle bit 1 If the I2C module is not in the idle mode, this bit may not be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled). RSEN: Repeated Start Condition Enabled bit (In I2C master mode only) 1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Repeated Start condition idle. bit 0 If the I2C module is not in the idle mode, this bit may not be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled). SEN: Start Condition Enabled bit (In I2C master mode only) 1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware. 0 = Start condition idle Note: Note: Note: Note: Note: If the I2C module is not in the idle mode, this bit may not be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled). Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' DS31017A-page 17-8 Preliminary - n = Value at POR reset 1997 Microchip Technology Inc. Section 17. MSSP 17.3 SPI Mode The SPI mode allows 8-bits of data to be synchronously transmitted and received simultaneously. All four modes of SPI are supported. To accomplish communication, typically three pins are used: * Serial Data Out (SDO) * Serial Data In (SDI) * Serial Clock (SCK) Additionally a fourth pin may be used when in a slave mode of operation: * Slave Select (SS) 17.3.1 Operation When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON1 register (SSPCON1<5:0>) and SSPSTAT<7:6>. These control bits allow the following to be specified: Master Mode (SCK is the clock output) Slave Mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Data input sample phase (middle or end of data output time) Clock edge (output data on rising/falling edge of SCK) Clock Rate (Master mode only) Slave Select Mode (Slave mode only) MSSP * * * * * * * Figure 17-4 shows the block diagram of the SSP module, when in SPI mode. Figure 17-4: SSP Block Diagram (SPI Mode) Internal data bus Read Write SSPBUF reg SSPSR reg SDI shift clock bit0 SDO SS Control Enable SS Edge Select 2 Clock Select SCK SSPM3:SSPM0 SMP:CKE 4 TMR2 output 2 2 Edge Select Prescaler TOSC 4, 16, 64 Data to TX/RX in SSPSR TRIS bit 1997 Microchip Technology Inc. Preliminary 17 DS31017A-page 17-9 PICmicro MID-RANGE MCU FAMILY The SSP consists of a transmit/receive Shift Register (SSPSR) and a buffer register (SSPBUF). The SSPSR shifts the data in and out of the device, MSb first. The SSPBUF holds the data that was written to the SSPSR, until the received data is ready. Once the 8-bits of data have been received, that byte is moved to the SSPBUF register. Then the buffer full detect bit, BF (SSPSTAT<0>), and the interrupt flag bit, SSPIF, are set. This double buffering of the received data (SSPBUF) allows the next byte to start reception before reading the data that was just received. Any write to the SSPBUF register during transmission/reception of data will be ignored, and the write collision detect bit, WCOL (SSPCON1<7>), will be set. User software must clear the WCOL bit so that it can be determined if the following write(s) to the SSPBUF register completed successfully. When the application software is expecting to receive valid data, the SSPBUF should be read before the next byte of data to transfer is written to the SSPBUF. Buffer full bit, BF (SSPSTAT<0>), indicates when SSPBUF has been loaded with the received data (transmission is complete). When the SSPBUF is read, the BF bit is cleared. This data may be irrelevant if the SPI is only a transmitter. Generally the SSP Interrupt is used to determine when the transmission/reception has completed. The SSPBUF must be read and/or written. If the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. Example 17-1 shows the loading of the SSPBUF (SSPSR) for data transmission. Example 17-1: BCF BSF LOOP BTFSS GOTO BCF MOVF MOVWF MOVF MOVWF Loading the SSPBUF (SSPSR) Register STATUS, RP1 STATUS, RP0 SSPSTAT, BF LOOP STATUS, RP0 SSPBUF, W RXDATA TXDATA, W SSPBUF ;Specify Bank1 ; ;Has data been received (transmit complete)? ;No ;Specify Bank0 ;W reg = contents of SSPBUF ;Save in user RAM, if data is meaningful ;W reg = contents of TXDATA ;New data to xmit The SSPSR is not directly readable or writable, and can only be accessed by addressing the SSPBUF register. Additionally, the SSP status register (SSPSTAT) indicates the various status conditions. 17.3.2 Enabling SPI I/O To enable the serial port, SSP Enable bit, SSPEN (SSPCON1<5>), must be set. To reset or reconfigure SPI mode, clear the SSPEN bit, re-initialize the SSPCON registers, and then set the SSPEN bit. This configures the SDI, SDO, SCK, and SS pins as serial port pins. For the pins to behave as the serial port function, some must have their data direction bits (in the TRIS register) appropriately programmed. That is: * * * * * SDI is automatically controlled by the SPI module SDO must have TRIS bit cleared SCK (Master mode) must have TRIS bit cleared SCK (Slave mode) must have TRIS bit set SS must have TRIS bit set Any serial port function that is not desired may be overridden by programming the corresponding data direction (TRIS) register to the opposite value. DS31017A-page 17-10 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.3.3 Typical Connection Figure 17-5 shows a typical connection between two microcontrollers. The master controller (Processor 1) initiates the data transfer by sending the SCK signal. Data is shifted out of both shift registers on their programmed clock edge, and latched on the opposite edge of the clock. Both processors should be programmed to same Clock Polarity (CKP), then both controllers would send and receive data at the same time. Whether the data is meaningful (or dummy data) depends on the application software. This leads to three scenarios for data transmission: * Master sends data -- Slave sends dummy data * Master sends data -- Slave sends data * Master sends dummy data -- Slave sends data Figure 17-5: SPI Master SSPM3:SSPM0 = 00xxb SPI Slave SSPM3:SSPM0 = 010xb SDI Serial Input Buffer (SSPBUF) Serial Input Buffer (SSPBUF) SDI Shift Register (SSPSR) SDO LSb Shift Register (SSPSR) MSb SCK Serial Clock PROCESSOR 1 1997 Microchip Technology Inc. MSSP SDO MSb 17 SPI Master/Slave Connection LSb SCK PROCESSOR 2 Preliminary DS31017A-page 17-11 PICmicro MID-RANGE MCU FAMILY 17.3.4 Master Mode The master can initiate the data transfer at any time because it controls the SCK. The master determines when the slave (Processor 2, Figure 17-5) is to broadcast data by the software protocol. In master mode the data is transmitted/received as soon as the SSPBUF register is written to. If the SPI is only going to receive, the SDO output could be disabled (programmed as an input). The SSPSR register will continue to shift in the signal present on the SDI pin at the programmed clock rate. As each byte is received, it will be loaded into the SSPBUF register as if a normal received byte (interrupts and status bits appropriately set). This could be useful in receiver applications as a "line activity monitor" mode. The clock polarity is selected by appropriately programming the CKP bit (SSPCON1<4>). This then would give waveforms for SPI communication as shown in Figure 17-6, Figure 17-8, and Figure 17-9 where the MSb is transmitted first. In master mode, the SPI clock rate (bit rate) is user programmable to be one of the following: * * * * FOSC/4 (or TCY) FOSC/16 (or 4 * TCY) FOSC/64 (or 16 * TCY) Timer2 output/2 This allows a maximum data rate (at 20 MHz) of 8.25 Mbps. Figure 17-6 Shows the waveforms for master mode. When the CKE bit is set, the SDO data is valid before there is a clock edge on SCK. The change of the input sample is shown based on the state of the SMP bit. The time when the SSPBUF is loaded with the received data is shown. DS31017A-page 17-12 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-6: SPI Mode Waveform (Master Mode) Write to SSPBUF SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) 4 clock modes SCK (CKP = 0 CKE = 1) 17 SCK (CKP = 1 CKE = 1) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDO (CKE = 1) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 SDI (SMP = 0) MSSP SDO (CKE = 0) bit0 bit7 Input Sample (SMP = 0) SDI (SMP = 1) bit0 bit7 Input Sample (SMP = 1) SSPIF Next Q4 cycle after Q2 SSPSR to SSPBUF 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-13 PICmicro MID-RANGE MCU FAMILY 17.3.5 Slave Mode In slave mode, the data is transmitted and received as the external clock pulses appear on SCK. When the last bit is latched, the SSPIF interrupt flag bit is set. While in slave mode the external clock is supplied by the external clock source on the SCK pin. This external clock must meet the minimum high and low times as specified in the electrical specifications. While in sleep mode, the slave can transmit/receive data. When a byte is receive the device will wake-up from sleep. 17.3.6 Slave Select Synchronization The SS pin allows a synchronous slave mode. The SPI must be in slave mode with SS pin control enabled (SSPCON1<3:0> = 04h). The pin must not be driven low for the SS pin to function as an input. The Data Latch must be high. When the SS pin is low, transmission and reception are enabled and the SDO pin is driven. When the SS pin goes high, the SDO pin is no longer driven, even if in the middle of a transmitted byte, and becomes a floating output. External pull-up/ pull-down resistors may be desirable, depending on the application. Note 1: When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> = 0100) the SPI module will reset if the SS pin is set to VDD. Note 2: If the SPI is used in Slave Mode with CKE is set, then the SS pin control must be enabled. When the SPI module resets, the bit counter is forced to 0. This can be done by either by forcing the SS pin to a high level or clearing the SSPEN bit. To emulate two-wire communication, the SDO pin can be connected to the SDI pin. When the SPI needs to operate as a receiver the SDO pin can be configured as an input. This disables transmissions from the SDO. The SDI can always be left as an input (SDI function) since it cannot create a bus conflict. DS31017A-page 17-14 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-7: Slave Synchronization Waveform SS SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) 17 Write to SSPBUF MSSP bit7 SDO SDI (SMP = 0) bit6 bit7 bit0 bit0 bit7 bit7 Input Sample (SMP = 0) SSPIF Interrupt Flag Next Q4 cycle after Q2 SSPSR to SSPBUF Figure 17-8: SPI Mode Waveform (Slave Mode with CKE = 0) SS optional SCK (CKP = 0 CKE = 0) SCK (CKP = 1 CKE = 0) Write to SSPBUF SDO SDI (SMP = 0) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 bit0 bit7 Input Sample (SMP = 0) SSPIF Interrupt Flag Next Q4 cycle after Q2 SSPSR to SSPBUF 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-15 PICmicro MID-RANGE MCU FAMILY Figure 17-9: SPI Mode Waveform (Slave Mode with CKE = 1) SS not optional SCK (CKP = 0 CKE = 1) SCK (CKP = 1 CKE = 1) Write to SSPBUF SDO SDI (SMP = 0) bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 bit0 bit7 Input Sample (SMP = 0) SSPIF Interrupt Flag Next Q4 cycle after Q2 SSPSR to SSPBUF DS31017A-page 17-16 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.3.7 Sleep Operation In master mode all module clocks are halted, and the transmission/reception will remain in that state until the device wakes from sleep. After the device returns to normal mode, the module will continue to transmit/receive data. In slave mode, the SPI transmit/receive shift register operates asynchronously to the device. This allows the device to be placed in sleep mode, and data to be shifted into the SPI transmit/receive shift register. When all 8-bits have been received, the MSSP interrupt flag bit will be set and if enabled will wake the device from sleep. 17.3.8 Effects of a Reset 17 A reset disables the MSSP module and terminates the current transfer. Table 17-1: Registers Associated with SPI Operation Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 INTCON GIE PEIE T0IE INTE RBIE(2) Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets T0IF INTF RBIF(2) 0000 0000 0000 0000 PIR SSPIF (1) 0 0 PIE SSPIE (1) 0 0 uuuu uuuu SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx SSPCON1 WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000 0000 0000 0000 0000 SSPSTAT SMP CKE D/A P S R/W UA BF Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in SPI mode. Note 1: The position of this bit is device dependent. 2: These bits may also be named GPIE and GPIF. 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-17 MSSP Name PICmicro MID-RANGE MCU FAMILY 17.4 SSP I 2CTM Operation The MSSP module in I 2C mode fully implements all master and slave functions (including general call support) and provides interrupts on start and stop bits in hardware to determine a free bus (multi-master function). The SSP module implements the standard mode specifications as well as 7-bit and 10-bit addressing. Appendix A gives an overview of the I 2C bus specification. A "glitch" filter is on the SCL and SDA pins when the pin is an input. This filter operates in both the 100 KHz and 400 KHz modes. In the 100 KHz mode, when these pins are an output, there is a slew rate control of the pin that is independent of device frequency. Figure 17-10: I2C Slave Mode Block Diagram Internal data bus Read Write SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb Address Match Match detect SSPADD reg Set, Reset S, P bits (SSPSTAT reg) Start and Stop bit detect Figure 17-11: I2C Master Mode Block Diagram Internal data bus Read SSPADD<6:0> 7 Write Baud Rate Generator SSPBUF reg SCL shift clock SSPSR reg SDA MSb LSb Match detect Address Match SSPADD reg Start and Stop bit detect / generate DS31017A-page 17-18 Preliminary Set/Clear S bit and Clear/Set P bit (SSPSTAT reg) and Set SSPIF 1997 Microchip Technology Inc. Section 17. MSSP Two pins are used for data transfer. These are the SCL pin, which is the clock, and the SDA pin, which is the data. Pins that are on the port are automatically configured when the I2C mode is enabled. The SSP module functions are enabled by setting SSP Enable bit, SSPEN (SSPCON1<5>). The SSP module has six registers for I2C operation. They are the: * * * * * * SSP Control Register1 (SSPCON1) SSP Control Register2 (SSPCON2) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - Not directly accessible SSP Address Register (SSPADD) The SSPCON1 register allows control of the I 2C operation. Four mode selection bits (SSPCON1<3:0>) allow one of the following I 2C modes to be selected: Before selecting any I 2C mode, the SCL and SDA pins must be programmed to inputs by setting the appropriate TRIS bits. Selecting an I 2C mode, by setting the SSPEN bit, enables the SCL and SDA pins to be used as the clock and data lines in I 2C mode. The SSPSTAT register gives the status of the data transfer. This information includes detection of a START or STOP bit, specifies if the received byte was data or address, if the next byte is the completion of 10-bit address, and if this will be a read or write data transfer. The SSPBUF is the register to which transfer data is written to or read from. The SSPSR register shifts the data in or out of the device. In receive operations, the SSPBUF and SSPSR create a double buffered receiver. This allows reception of the next byte to begin before reading the last byte of received data. When the complete byte is received, it is transferred to the SSPBUF register and flag bit SSPIF is set. If another complete byte is received before the SSPBUF register is read, a receiver overflow has occurred and the SSPOV bit (SSPCON1<6>) is set and the byte in the SSPSR is lost. The SSPADD register holds the slave address. In 10-bit mode, the user needs to write the high byte of the address (1111 0 A9 A8 0). Following the high byte address match, the low byte of the address needs to be loaded (A7:A0). 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-19 MSSP * I 2C Slave mode (7-bit address) * I 2C Slave mode (10-bit address) * I 2C Master mode, clock = OSC/4 (SSPADD +1) 17 PICmicro MID-RANGE MCU FAMILY 17.4.1 Slave Mode In slave mode, the SCL and SDA pins must be configured as inputs. The SSP module will override the input state with the output data when required (slave-transmitter). When an address is matched or the data transfer after an address match is received, the hardware automatically will generate the acknowledge (ACK) pulse, and then load the SSPBUF register with the received value currently in the SSPSR register. There are certain conditions that will cause the SSP module not to give this ACK pulse. These are if either (or both): a) b) The buffer full bit, BF (SSPSTAT<0>), was set before the transfer was received. The overflow bit, SSPOV (SSPCON1<6>), was set before the transfer was received. If the BF bit is set, the SSPSR register value is not loaded into the SSPBUF, but the SSPIF and SSPOV bits are set. Table 17-2 shows what happens when a data transfer byte is received, given the status of the BF and SSPOV bits. The shaded cells show the condition where user software did not properly clear the overflow condition. The BF flag bit is cleared by reading the SSPBUF register while bit SSPOV is cleared through software. The SCL clock input must have a minimum high and low time for proper operation. The high and low times of the I2C specification as well as the requirement of the SSP module is shown in timing parameters 100 and 101 of the "Electrical Specifications" section. DS31017A-page 17-20 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.1.1 Addressing Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, the 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register on the falling edge of the eighth SCL pulse. The buffer full bit, BF, is set on the falling edge of the eighth SCL pulse. An ACK pulse is generated. SSP interrupt flag bit, SSPIF, is set (interrupt is generated if enabled) - on the falling edge of the ninth SCL pulse. 1. 2. 3. 4. 5. 6. 7. 8. 9. Receive first (high) byte of Address (the SSPIF, BF, and UA (SSPSTAT<1>) bits are set). Update the SSPADD register with second (low) byte of Address (clears the UA bit and releases the SCL line). Read the SSPBUF register (clears the BF bit) and clear flag bit SSPIF. Receive second (low) byte of Address (the SSPIF, BF, and UA bits are set). Update the SSPADD register with the first (high) byte of Address. This will clear the UA bit and release the SCL line. Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Receive repeated START condition. Receive first (high) byte of Address (the SSPIF and BF bits are set). Read the SSPBUF register (clears the BF bit) and clear the SSPIF flag bit. Note: Following the Repeated Start condition (step 7) in 10-bit mode, the user only needs to match the first 7-bit address. The user does not update the SSPADD for the second half of the address. Table 17-2: Data Transfer Received Byte Actions Status Bits as Data Transfer is Received BF SSPOV SSPSR SSPBUF Generate ACK Pulse 0 1 1 0 0 0 1 1 Yes No No Yes Yes No No No Set bit SSPIF (SSP Interrupt occurs if enabled) Yes Yes Yes Yes Note: Shaded cells show the conditions where the user software did not properly clear the overflow condition 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-21 MSSP In 10-bit address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. The R/W bit (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address the first byte would equal `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for a 10-bit address is as follows, with steps 7- 9 for slave-transmitter: 17 PICmicro MID-RANGE MCU FAMILY 17.4.1.2 Slave Reception When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as either the BF bit (SSPSTAT<0>) is set or the SSPOV bit (SSPCON1<6>) is set. An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software. The SSPSTAT register is used to determine the status of the received byte. Note: DS31017A-page 17-22 The SSPBUF will be loaded if the SSPOV bit is set and the BF flag bit is cleared. If a read of the SSPBUF was performed, but the user did not clear the state of the SSPOV bit before the next receive occurred. The ACK is not sent and the SSPBUF is updated. Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.1.3 Slave Transmission When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit, and the SCL pin is held low. The transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit (SSPCON1<4>). The master should monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 17-13). An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in software, and the SSPSTAT register is used to determine the status of the byte transfer. The SSPIF flag bit is set on the falling edge of the ninth clock pulse. Figure 17-12: I 2C Slave Mode Waveforms for Reception (7-bit Address) Receiving Address Receiving Data R/W=0 Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 SDA SCL 1 S 2 3 4 5 6 7 9 8 1 2 3 4 5 6 7 8 9 1 2 3 4 5 9 8 7 6 SSPIF P Bus Master terminates transfer BF (SSPSTAT<0>) Cleared in software SSPBUF register is read SSPOV (SSPCON1<6>) Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent. Figure 17-13: I 2C Slave Mode Waveforms for Transmission (7-bit Address) Receiving Address SDA SCL A7 S A6 1 2 Data in sampled R/W = 1 A5 A4 A3 A2 A1 3 4 5 6 7 ACK 8 9 R/W = 0 ACK Transmitting Data D7 1 SCL held low while CPU responds to SSPIF D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 9 P SSPIF BF (SSPSTAT<0>) cleared in software SSPBUF is written in software From SSP interrupt service routine CKP (SSPCON1<4>) Set bit after writing to SSPBUF (the SSPBUF must be written-to before the CKP bit can be set) 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-23 17 MSSP As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the not ACK is latched by the slave, the slave logic is reset and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should be enabled by setting the CKP bit. DS31017A-page 17-24 Preliminary UA (SSPSTAT<1>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 S SCL 2 1 4 1 5 0 6 7 A9 A8 UA is set indicating that the SSPADD needs to be updated SSPBUF is written with contents of SSPSR 3 1 8 9 ACK Receive First Byte of Address R/W = 0 1 1 3 4 5 Cleared in software 2 7 UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated. 6 A6 A5 A4 A3 A2 A1 8 A0 Receive Second Byte of Address Dummy read of SSPBUF to clear BF flag A7 9 ACK 2 3 1 4 1 Cleared in software 1 1 Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag Sr 1 5 0 6 7 A9 A8 Receive First Byte of Address 8 9 R/W=1 ACK 1 3 4 5 6 7 8 9 ACK P Write of SSPBUF initiates transmit Cleared in software Bus Master terminates transfer CKP has to be set for clock to be released 2 D4 D3 D2 D1 D0 Transmitting Data Byte D7 D6 D5 Master sends NACK Transmit is complete Figure 17-14: SDA Clock is held low until update of SSPADD has taken place PICmicro MID-RANGE MCU FAMILY I2C Slave Mode Waveform (Transmission 10-bit Address) 1997 Microchip Technology Inc. 1997 Microchip Technology Inc. Preliminary UA (SSPSTAT<1>) BF (SSPSTAT<0>) (PIR1<3>) SSPIF 1 SCL S 1 SDA 2 1 3 1 5 0 6 A9 7 A8 UA is set indicating that the SSPADD needs to be updated 8 9 ACK R/W = 0 SSPBUF is written with contents of SSPSR 4 1 Receive First Byte of Address 1 3 A5 4 A4 Cleared in software 2 A6 5 A3 6 A2 7 A1 8 A0 UA is set indicating that SSPADD needs to be updated Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag A7 Receive Second Byte of Address 9 ACK 3 D5 4 D4 5 D3 Receive Data Byte Cleared in software 2 D6 Cleared by hardware when SSPADD is updated. Dummy read of SSPBUF to clear BF flag 1 D7 MSSP Clock is held low until update of SSPADD has taken place 6 D2 D0 8 7 9 ACK R/W = 1 D1 Read of SSPBUF clears BF flag P Bus Master terminates transfer Section 17. MSSP Figure 17-15: I2C Slave Mode Waveform (Reception 10-bit Address) 17 DS31017A-page 17-25 PICmicro MID-RANGE MCU FAMILY 17.4.2 General Call Address Support The addressing procedure for the I2C bus is such that the first byte after the START condition usually determines which device will be the slave addressed by the master. The exception is the general call address which can address all devices. When this address is used, all devices should, in theory, respond with an acknowledge. The general call address is one of eight addresses reserved for specific purposes by the I2C protocol. It consists of all 0's with R/W = 0. The general call address is recognized when the General Call Enable bit (GCEN) is enabled (SSPCON2<7> set). Following a start-bit detect, 8-bits are shifted into SSPSR and the address is compared against SSPADD, and is also compared to the general call address, fixed in hardware. If the general call address matches, the SSPSR is transferred to the SSPBUF, the BF flag bit is set (eight bit), and on the falling edge of the ninth bit (ACK bit) the SSPIF interrupt flag bit is set. When the interrupt is serviced. The source for the interrupt can be checked by reading the contents of the SSPBUF to determine if the address was device specific or a general call address. In 10-bit mode, the SSPADD is required to be updated for the second half of the address to match, and the UA bit is set (SSPSTAT<1>). If the general call address is sampled when the GCEN bit is set while the slave is configured in 10-bit address mode, then the second half of the address is not necessary, the UA bit will not be set, and the slave will begin receiving data after the acknowledge (Figure 17-16). Figure 17-16: Slave Mode General Call Address Sequence (7 or 10-bit Address Mode) Address is compared to General Call Address after ACK, set interrupt R/W = 0 ACK D7 General Call Address SDA Receiving data ACK D6 D5 D4 D3 D2 D1 D0 2 3 4 5 6 7 8 SCL S 1 2 3 4 5 6 7 8 9 1 9 SSPIF BF (SSPSTAT<0>) Cleared in software SSPBUF is read SSPOV (SSPCON1<6>) '0' GCEN (SSPCON2<7>) '1' DS31017A-page 17-26 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.3 Sleep Operation While in sleep mode, the I2C module can receive addresses or data, and when an address match or complete byte transfer occurs wake the processor from sleep (if the MSSP interrupt is enabled). 17.4.4 Effect of a Reset A reset disables the MSSP module and terminates the current transfer. Table 17-3: Registers Associated with I2C Operation Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other resets INTCON GIE PEIE T0IE INTE RBIE(2) T0IF INTF RBIF(2) 0000 0000 0000 0000 0, 0 0, 0 0, 0 0, 0 (1) PIR SSPIF, BCLIF SSPIE, BCLIF (1) PIE (I2C SSPADD mode) Synchronous Serial Port Address Register (slave mode)/Baud Rate Generator (master mode) 0000 0000 0000 0000 SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPCON1 WCOL SSPOV SSPEN CKP SSPCON2 GCEN ACKSTAT ACKDT ACKEN SSPSTAT SMP CKE D/A P xxxx xxxx uuuu uuuu SSPM3 SSPM2 SSPM1 SSPM0 0000 0000 0000 0000 RCEN PEN RSEN SEN 0000 0000 0000 0000 S R/W UA BF 0000 0000 0000 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in I2C mode. Note 1: The position of these bits is device dependent. 2: These bits may also be named GPIE and GPIF. 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-27 17 MSSP Name PICmicro MID-RANGE MCU FAMILY 17.4.5 Master Mode Master mode of operation is supported by interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle with both the S and P bits clear. In master mode the SCL and SDA lines are manipulated by the SSP hardware. The following events will cause SSP Interrupt Flag bit, SSPIF, to be set (SSP Interrupt if enabled): * * * * * START condition STOP condition Data transfer byte transmitted/received Acknowledge Transmit Repeated Start Figure 17-17: SSP Block Diagram (I2C Master Mode) Internal data bus Read SSPM3:SSPM0 SSPADD<6:0> Write SSPBUF shift clock SDA SDA in SSPSR SCL in Bus Collision DS31017A-page 17-28 LSb Start bit, Stop bit, Acknowledge Generate Start bit detect Stop bit detect Write collision detect Clock Arbitration State counter for end of XMIT/RCV Preliminary clock cntl SCL Receive Enable MSb clock arbitrate/WCOL detect (hold off clock source) Baud rate generator Set/Reset, S, P, WCOL (SSPSTAT) Set SSPIF, BCLIF Reset ACKSTAT, PEN (SSPCON2) 1997 Microchip Technology Inc. Section 17. MSSP 17.4.6 Multi-Master Mode In multi-master mode, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. Control of the I 2C bus may be taken when the P bit (SSPSTAT<4>) is set, or the bus is idle with both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. In multi-master operation, the SDA line must be monitored, for arbitration, to see if the signal level is the expected output level. This check is performed in hardware, with the result placed in the BCLIF bit. The states where arbitration can be lost are: 17.4.7 17 Address Transfer Data Transfer A Start Condition A Repeated Start Condition An Acknowledge Condition MSSP * * * * * I2C Master Mode Support Master Mode is enabled by setting and clearing the appropriate SSPM bits in SSPCON1 and by setting the SSPEN bit. Once master mode is enabled, the user has six options. 1. 2. 3. 4. 5. 6. Assert a start condition on SDA and SCL. Assert a Repeated Start condition on SDA and SCL. Write to the SSPBUF register initiating transmission of data/address. Generate a stop Condition on SDA and SCL. Configure the I2C port to receive data. Generate an acknowledge condition at the end of a received byte of data. Note: 1997 Microchip Technology Inc. The SSP Module when configured in I2C Master Mode does not allow queueing of events. For instance: The user is not allowed to initiate a start condition, and immediately write the SSPBUF register to imitate transmission before the START condition is complete. In this case the SSPBUF will not be written to, and the WCOL bit will be set, indicating that a write to the SSPBUF did not occur. Preliminary DS31017A-page 17-29 PICmicro MID-RANGE MCU FAMILY 17.4.7.1 I2C Master Mode Operation The master device generates all of the serial clock pulses and the START and STOP conditions. A transfer is ended with a STOP condition or with a repeated START condition. Since the repeated START condition is also the beginning of the next serial transfer, the I2C bus will not be released. In Master transmitter mode serial data is output through SDA, while SCL outputs the serial clock. The first byte transmitted contains the slave address of the receiving device, (7 bits) and the Read/Write (R/W) bit. In this case the R/W bit will be logic '0'. Serial data is transmitted 8 bits at a time. After each byte is transmitted, an acknowledge bit is received. START and STOP conditions are output to indicate the beginning and the end of a serial transfer. In Master receive mode the first byte transmitted contains the slave address of the transmitting device (7 bits) and the R/W bit. In this case the R/W bit will be logic `1`. Thus the first byte transmitted is a 7-bit slave address followed by a '1' to indicate receive bit. Serial data is received via SDA while SCL outputs the serial clock. Serial data is received 8 bits at a time. After each byte is received, an acknowledge bit is transmitted. START and STOP conditions indicate the beginning and end of transmission. The baud rate generator used for SPI mode operation is used to set the SCL clock frequency for either 100 kHz, 400 kHz, or 1 MHz I2C operation. The baud rate generator reload value is contained in the lower 7 bits of the SSPADD register. The baud rate generator will automatically begin counting on a write to the SSPBUF. Once the given operation is complete (i.e., transmission of the last data bit is followed by ACK) the internal clock will automatically stop counting and the SCL pin will remain in its last state. A typical transmit sequence would go as follows: a) b) c) d) e) f) g) h) i) j) k) l) DS31017A-page 17-30 The user generates a Start Condition by setting the START enable bit, SEN (SSPCON2<0>). SSPIF is set. The SSP module will wait the required start time before any other operation takes place. The user loads the SSPBUF with the address to transmit. Address is shifted out the SDA pin until all 8 bits are transmitted. The SSP Module shifts in the ACK bit from the slave device, and writes its value into the SSPCON2 register (SSPCON2<6>). The SSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPIF bit. The user loads the SSPBUF with eight bits of data. DATA is shifted out the SDA pin until all 8 bits are transmitted. The SSP Module shifts in the ACK bit from the slave device, and writes its value into the SSPCON2 register (SSPCON2<6>). The SSP module generates an interrupt at the end of the ninth clock cycle by setting the SSPIF bit. The user generates a STOP condition by setting the STOP enable bit, PEN (SSPCON2<2>). Interrupt is generated once the stop condition is complete. Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.8 Baud Rate Generator In I2C master mode, the reload value for the BRG is located in the lower 7 bits of the SSPADD register (Figure 17-18). When the BRG is loaded with this value, the BRG counts down to 0 and stops until another reload has taken place. In I2C master mode, the BRG is reloaded automatically. If Clock Arbitration is taking place for instance, the BRG will be reloaded when the SCL pin is sampled high (Figure 17-19). Figure 17-18: Baud Rate Generator Block Diagram SSPM3:SSPM0 SSPADD<6:0> 17 SSPM3:SSPM0 Reload SCL Control BRG Down Counter Fosc/4 Figure 17-19: Baud Rate Generator Timing With Clock Arbitration SDA DX DX-1 SCL de-asserted but slave holds SCL low (clock arbitration) SCL allowed to transition high SCL BRG counts down BRG counts down BRG value 03h 02h 01h BRG counts down 00h (hold off) 03h 02h SCL is sampled high, reload takes place, and BRG starts its count. BRG reload 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-31 MSSP CLKOUT Reload PICmicro MID-RANGE MCU FAMILY 17.4.9 I2C Master Mode Start Condition Timing To initiate a START condition the user sets the start condition enable bit, SEN (SSPCON2<0>). If the SDA and SCL pins are sampled high, the baud rate generator is re-loaded with the contents of SSPADD<6:0>, and starts its count. If SCL and SDA are both sampled high when the baud rate generator times out (TBRG), the SDA pin is driven low. The action of the SDA being driven low while SCL is high is the START condition, and causes the S bit (SSPSTAT<3>) to be set. Following this, the baud rate generator is reloaded with the contents of SSPADD<6:0> and resumes its count. When the baud rate generator times out (TBRG) the SEN bit (SSPCON2<0>) will be automatically cleared by hardware, the baud rate generator is suspended leaving the SDA line held low, and the START condition is complete. Note: 17.4.9.1 If at the beginning of START condition the SDA and SCL pins are already sampled low, or if during the START condition the SCL line is sampled low before the SDA line is driven low, a bus collision occurs, the Bus Collision Interrupt Flag,BCLIF, is set, the START condition is aborted, and the I2C module is reset into its IDLE state. WCOL Status Flag If the user writes the SSPBUF when an START sequence is in progress, then WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). Note: Because queueing of events is not allowed, writing to the lower 5 bits of SSPCON2 is disabled until the START condition is complete. Figure 17-20: First Start Bit Timing Set S bit (SSPSTAT<3>) Write to SEN bit occurs here. SDA = 1, SCL = 1 TBRG At completion of start bit, Hardware clears SEN bit and sets SSPIF bit TBRG Write to SSPBUF occurs here 1st Bit SDA 2nd Bit TBRG SCL TBRG S DS31017A-page 17-32 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-21: Start Condition Flowchart SSPEN = 1, SSPCON1<3:0> = 1000 Idle Mode SEN (SSPCON2<0> = 1) Bus collision detected, Set BCLIF, Release SCL, Clear SEN 17 No SDA = 1? SCL = 1? MSSP Yes Load BRG with SSPADD<6:0> No No No Yes SCL= 0? SDA = 0? Yes BRG Rollover? Yes Reset BRG Force SDA = 0, Load BRG with SSPADD<6:0>, Set S bit No SCL = 0? Yes No BRG rollover? Yes Reset BRG Force SCL = 0, Start Condition Done, Clear SEN. Set SSPIF 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-33 PICmicro MID-RANGE MCU FAMILY 17.4.10 I2C Master Mode Repeated Start Condition Timing A Repeated Start condition occurs when the RSEN bit (SSPCON2<1>) is programmed high and the I2C logic module is in the idle state. When the RSEN bit is set, the SCL pin is asserted low. When the SCL pin is sampled low, the baud rate generator is loaded with the contents of SSPADD<5:0>, and begins counting. The SDA pin is released (brought high) for one baud rate generator count (TBRG). When the baud rate generator times out, if SDA is sampled high, the SCL pin will be de-asserted (brought high). When SCL is sampled high the baud rate generator is re-loaded with the contents of SSPADD<6:0> and begins counting. SDA and SCL must be sampled high for one TBRG. This action is then followed by assertion of the SDA pin (SDA = 0) for one TBRG while SCL is high. Following this, the RSEN bit (SSPCON2<1>) will be automatically cleared, and the baud rate generator is not reloaded, leaving the SDA pin held low. As soon as a start condition is detected on the SDA and SCL pins, the S bit (SSPSTAT<3>) will be set. The SSPIF bit will not be set until the baud rate generator has timed-out. Note 1: If RSEN is programmed while any other event is in progress, it will not take effect. Note 2: A bus collision during the Repeated Start condition occurs if: * SDA is sampled low when SCL goes from low to high. * SCL goes low before SDA is asserted low. This may indicates that another master is attempting to transmit a data `1'. Immediately following the SSPIF bit getting set, the user may write the SSPBUF with the 7-bit address in 7-bit mode, or the default first address in 10-bit mode. After the first eight bits are transmitted and an ACK is received, the user may then transmit an additional eight bits of address (10-bit mode) or eight bits of data (7-bit mode). DS31017A-page 17-34 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.10.1 WCOL Status Flag If the user writes the SSPBUF when a Repeated Start sequence is in progress, then WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). Note: Because queueing of events is not allowed, writing of the lower 5 bits of SSPCON2 is disabled until the Repeated Start condition is complete. Figure 17-22: Repeat Start Condition Waveform Set S (SSPSTAT<3>) Write to SSPCON2 occurs here. SDA = 1, SCL(no change) SDA = 1, SCL = 1 TBRG At completion of start bit, hardware clear RSEN bit and set SSPIF TBRG 17 TBRG 1st Bit Write to SSPBUF occurs here. Falling edge of ninth clock End of Xmit TBRG SCL TBRG Sr = Repeated Start 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-35 MSSP SDA PICmicro MID-RANGE MCU FAMILY Figure 17-23: Repeated Start Condition Flowchart (part 1 of 2) Start Idle Mode, SSPEN = 1, SSPCON1<3:0> = 1000 B RSEN = 1 Force SCL = 0 No SCL = 0? Yes Release SDA, Load BRG with SSPADD<6:0> No BRG rollover? Yes Release SCL (Clock Arbitration) No SCL = 1? Yes Bus Collision, Set BCLIF, Release SDA, Clear RSEN No SDA = 1? Yes Load BRG with SSPADD<6:0> C DS31017A-page 17-36 Preliminary A 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-24: Repeated Start Condition Flowchart (part 2 of 2) B C A Yes No No No SDA = 0? SCL = 1? Yes BRG rollover? 17 Yes Reset BRG Set S No SCL = '0'? Yes Reset BRG 1997 Microchip Technology Inc. Preliminary No BRG rollover? Yes Force SCL = 0, Repeated Start condition done, Clear RSEN, Set SSPIF. DS31017A-page 17-37 MSSP Force SDA = 0, Load BRG with SSPADD<6:0> PICmicro MID-RANGE MCU FAMILY 17.4.11 I2C Master Mode Transmission Transmission of a data byte, a 7-bit address, or the either half of a 10-bit address is accomplished by simply writing a value to SSPBUF register. This action will set the buffer full flag bit, BF, and allow the baud rate generator to begin counting and start the next transmission. Each bit of address/data will be shifted out onto the SDA pin after the falling edge of SCL is asserted (see data hold time specification parameters 106). SCL is held low for one baud rate generator roll over count (TBRG). Data should be valid before SCL is released high (see Data setup time specification parameters 107). When the SCL pin is released high, it is held that way for TBRG, the data on the SDA pin must remain stable for that duration and some hold time after the next falling edge of SCL. After the eighth bit is shifted out (the falling edge of the eighth clock), the BF flag is cleared and the master releases SDA allowing the slave device being addressed to respond with an ACK bit during the ninth bit time, if an address match occurs or if data was received properly. The status of ACK is written into the ACKDT bit on the falling edge of the ninth clock. If the master receives an acknowledge, the acknowledge status bit, ACKSTAT, is cleared. If not, the bit is set. After the ninth clock the SSPIF bit is set, and the master clock (baud rate generator) is suspended until the next data byte is loaded into the SSPBUF leaving SCL low and SDA unchanged (Figure 17-26). After the write to the SSPBUF, each bit of address will be shifted out on the falling edge of SCL until all seven address bits and the R/W bit are completed. On the falling edge of the eighth clock the master will de-assert the SDA pin allowing the slave to respond with an acknowledge. On the falling edge of the ninth clock the master will sample the SDA pin to see if the address was recognized by a slave. The status of the ACK bit is loaded into the ACKSTAT status bit (SSPCON2<6>). Following the falling edge of the ninth clock transmission of the address, the SSPIF is set, the BF flag is cleared, and the baud rate generator is turned off until another write to the SSPBUF takes place, holding SCL low and allowing SDA to float. 17.4.11.1 BF Status Flag In transmit mode, the BF bit (SSPSTAT<0>) is set when the CPU writes to SSPBUF and is cleared when all 8 bits are shifted out. 17.4.11.2 WCOL Status Flag If the user writes the SSPBUF when a transmit is already in progress (i.e. SSPSR is still shifting out a data byte), then WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). WCOL must be cleared in software. 17.4.11.3 ACKSTAT Status Flag In transmit mode, the ACKSTAT bit (SSPCON2<6>) is cleared when the slave has sent an acknowledge (ACK = 0), and is set when the slave does not acknowledge (ACK = 1). A slave sends an acknowledge when it has recognized its address (including a general call), or when the slave has properly received its data. DS31017A-page 17-38 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-25: Master Transmit Flowchart Idle Mode Write SSPBUF Num_Clocks = 0, BF = 1 Force SCL = 0 17 Release SDA so slave can drive ACK, Force BF = 0 Yes Num_Clocks = 8? BRG rollover? MSSP No Load BRG with SSPADD<6:0>, start BRG count Load BRG with SSPADD<6:0>, start BRG count, SDA = Current Data bit BRG rollover? No No Yes Yes Force SCL = 1, Stop BRG Stop BRG, Force SCL = 1 (Clock Arbitration) SCL = 1? (Clock Arbitration) No SCL = 1? No Yes Yes SDA = Data bit? Read SDA and place into ACKSTAT bit (SSPCON2<6>) No Bus collision detected Set BCLIF, hold prescale off, Clear XMIT enable Yes Load BRG with SSPADD<6:0>, count high time Load BRG with SSPADD<6:0>, count SCL high time No Rollover? Yes BRG rollover? No No SCL = 0? SDA = Data bit? Yes Force SCL = 0, Set SSPIF Yes Yes No Reset BRG Num_Clocks = Num_Clocks + 1 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-39 DS31017A-page 17-40 Preliminary S R/W PEN SEN BF (SSPSTAT<0>) SSPIF SCL SDA A6 A5 A4 A3 A2 A1 3 4 5 cleared in software 2 6 7 8 9 After start condition SEN cleared by hardware. SSPBUF written 1 D7 3 D5 4 D4 5 D3 6 D2 7 D1 SSPBUF is written in software 8 D0 cleared in software service routine From SSP interrupt 2 D6 Transmitting Data or Second Half of 10-bit Address From slave clear ACKSTAT bit SSPCON2<6> 1 SCL held low while CPU responds to SSPIF ACK = 0 R/W = 0 SSPBUF written with 7 bit address and R/W start transmit A7 Transmit Address to Slave SEN = 0 Write SSPCON2<0> SEN = 1 START condition begins P Cleared in software 9 ACK ACKSTAT in SSPCON2 = 1 PICmicro MID-RANGE MCU FAMILY Figure 17-26: I 2C Master Mode Waveform (Transmission, 7 or 10-bit Address) 1997 Microchip Technology Inc. Section 17. MSSP 17.4.12 I2C Master Mode Reception Master mode reception is enabled by programming the receive enable bit, RCEN (SSPCON2<3>). Note: The SSP Module must be in an IDLE STATE before the RCEN bit is set, or the RCEN bit will be disregarded. The baud rate generator begins counting, and on each rollover, the state of the SCL pin changes (high to low/low to high), and data is shifted into the SSPSR. After the falling edge of the eighth clock, the receive enable flag is automatically cleared, the contents of the SSPSR are loaded into the SSPBUF, the BF flag bit is set, the SSPIF flag bit is set, and the baud rate generator is suspended from counting, holding SCL low. The SSP is now in IDLE state, awaiting the next command. When the buffer is read by the CPU, the BF flag bit is automatically cleared. The user can then send an acknowledge bit at the end of reception, by setting the acknowledge sequence enable bit, ACKEN (SSPCON2<4>). 17 17.4.12.1 BF Status Flag 17.4.12.2 SSPOV Status Flag In receive operation, the SSPOV bit is set when 8 bits are received into the SSPSR, and the BF flag bit is already set from a previous reception. 17.4.12.3 WCOL Status Flag If the user writes the SSPBUF when a receive is already in progress (i.e. SSPSR is still shifting in a data byte), then the WCOL bit is set and the contents of the buffer are unchanged (the write doesn't occur). 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-41 MSSP In receive operation, the BF bit is set when an address or data byte is loaded into SSPBUF from SSPSR. It is cleared when the SSPBUF register is read. PICmicro MID-RANGE MCU FAMILY Figure 17-27: Master Receiver Flowchart Idle mode RCEN = 1 Num_Clocks = 0, Release SDA Force SCL=0, Load BRG w/ SSPADD<6:0>, start count BRG rollover? No Yes Release SCL (Clock Arbitration) SCL = 1? No Yes Sample SDA, Shift data into SSPSR Load BRG with SSPADD<6:0>, start count. BRG rollover? No Yes SCL = 0? No Yes Num_Clocks = Num_Clocks + 1 No Num_Clocks = 8? Yes Force SCL = 0, Set SSPIF, Set BF. Move contents of SSPSR into SSPBUF, Clear RCEN. DS31017A-page 17-42 Preliminary 1997 Microchip Technology Inc. 1997 Microchip Technology Inc. Preliminary S ACKEN SSPOV BF (SSPSTAT<0>) SDA = 0, SCL = 1 while CPU responds to SSPIF SSPIF SCL SDA 1 A7 2 4 5 Cleared in software 3 6 A6 A5 A4 A3 A2 Transmit Address to Slave SEN = 0 Write to SSPBUF occurs here Start XMIT 7 A1 8 9 R/W = 1 ACK ACK from Slave 2 3 5 6 7 8 D0 9 ACK 2 3 4 5 6 7 Cleared in software Set SSPIF interrupt at end of acknowledge sequence Data shifted in on falling edge of CLK 1 D7 D6 D5 D4 D3 D2 D1 Cleared in software Set SSPIF at end of receive 9 ACK is not sent ACK P Set SSPIF interrupt at end of acknowledge sequence Bus Master terminates transfer Set P bit (SSPSTAT<4>) and SSPIF PEN bit = 1 written here SSPOV is set because SSPBUF is still full 8 D0 RCEN cleared automatically Set ACKEN start acknowledge sequence SDA = ACKDT = 1 Receiving Data from Slave RCEN = 1 start next receive ACK from Master SDA = ACKDT = 0 Last bit is shifted into SSPSR and contents are unloaded into SSPBUF Cleared in software Set SSPIF interrupt at end of receive 4 Cleared in software 1 D7 D6 D5 D4 D3 D2 D1 Receiving Data from Slave RCEN cleared automatically Master configured as a receiver by programming SSPCON2<3>, (RCEN = 1) MSSP Write to SSPCON2<0> (SEN = 1) Begin Start Condition Write to SSPCON2<4> to start acknowledge sequence SDA = ACKDT (SSPCON2<5>) = 0 Section 17. MSSP Figure 17-28: I 2C Master Mode Waveform (Reception 7-Bit Address) 17 DS31017A-page 17-43 PICmicro MID-RANGE MCU FAMILY 17.4.13 Acknowledge Sequence Timing An acknowledge sequence is enabled by setting the acknowledge sequence enable bit, ACKEN (SSPCON2<4>). When this bit is set, the SCL pin is pulled low and the contents of the acknowledge data bit is presented on the SDA pin. If the user wishes to generate an acknowledge, then the ACKDT bit should be cleared. If not, the user should set the ACKDT bit before starting an acknowledge sequence. The baud rate generator then counts for one rollover period (TBRG), and the SCL pin is de-asserted (pulled high). When the SCL pin is sampled high (clock arbitration), the baud rate generator counts for TBRG. The SCL pin is then pulled low. Following this, the ACKEN bit is automatically cleared, the baud rate generator is turned off, and the SSP module then goes into IDLE mode (Figure 17-29). 17.4.13.1 WCOL Status Flag If the user writes the SSPBUF when an acknowledge sequence is in progress, then WCOL is set and the contents of the buffer are unchanged (the write doesn't occur). Figure 17-29: Acknowledge Sequence Waveform Acknowledge sequence starts here, Write to SSPCON2 ACKEN = 1, ACKDT = 0 ACKEN automatically cleared TBRG TBRG SDA SCL ACK D0 8 9 SSPIF Set SSPIF at the end of receive Cleared in software Cleared in software Set SSPIF at the end of acknowledge sequence Note: TBRG= one baud rate generator period. DS31017A-page 17-44 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-30: Acknowledge Flowchart Idle mode Set ACKEN Force SCL = 0 BRG rollover? Yes 17 No No SCL = 0? Yes Drive ACKDT bit (SSPCON2<5>) onto SDA pin, Load BRG with SSPADD<6:0>, start count. SCL = 0? Reset BRG Force SCL = 0, Clear ACKEN Set SSPIF No No ACKDT = 1? Yes No BRG rollover? Yes Yes Force SCL = 1 SDA = 1? No Bus collision detected, Set BCLIF, Release SCL, Clear ACKEN No SCL = 1? (Clock Arbitration) Yes Load BRG with SSPADD <6:0>, start count. 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-45 MSSP Yes PICmicro MID-RANGE MCU FAMILY 17.4.14 Stop Condition Timing A stop bit is asserted on the SDA pin at the end of a receive/transmit by setting the Stop sequence enable bit, PEN (SSPCON2<2>). At the end of a receive/transmit the SCL line is held low after the falling edge of the ninth clock. When the PEN bit is set, the master will assert the SDA line low. When the SDA line is sampled low, the baud rate generator is reloaded and counts down to 0. When the baud rate generator times out, the SCL pin will be brought high, and one TBRG (baud rate generator rollover count) later, the SDA pin will be de-asserted. When the SDA pin is sampled high while SCL is high the P bit (SSPSTAT<4>) is set. A TBRG later, the PEN bit is cleared and the SSPIF bit is set (Figure 17-31). Whenever the firmware decides to take control of the bus, it will first determine if the bus is busy by checking the S and P bits in the SSPSTAT register. If the bus is busy, then the CPU can be interrupted (notified) when a Stop bit is detected (i.e. bus is free). 17.4.14.1 WCOL Status Flag If the user writes the SSPBUF when a STOP sequence is in progress, then the WCOL bit is set and the contents of the buffer are unchanged (the write doesn't occur). Figure 17-31: Stop Condition Receive or Transmit Mode SCL = 1 for TBRG, followed by SDA = 1 for TBRG after SDA sampled high. P bit (SSPSTAT<4>) is set Write to SSPCON2 Set PEN PEN bit (SSPCON2<2>) is cleared by hardware and the SSPIF bit is set Falling edge of 9th clock TBRG SCL SDA ACK P TBRG TBRG TBRG SCL brought high after TBRG SDA asserted low before rising edge of clock to setup stop condition. Note: TBRG = one baud rate generator period. DS31017A-page 17-46 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-32: Stop Condition Flowchart Idle Mode, SSPEN = 1, SSPCON1<3:0> = 1000 PEN = 1 Start BRG Force SDA = 0 SCL doesn't change BRG rollover? No SDA = 0? No 17 Yes MSSP Release SDA, Start BRG Yes Start BRG BRG rollover? BRG rollover? No No Yes No P bit Set? Yes De-assert SCL, SCL = 1 Yes (Clock Arbitration) SCL = 1? Bus Collision detected, Set BCLIF, Clear PEN No SDA going from 0 to 1 while SCL = 1, Set SSPIF, Stop Condition done PEN Cleared Yes 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-47 PICmicro MID-RANGE MCU FAMILY 17.4.15 Clock Arbitration Clock arbitration occurs when the master, during any receive, transmit, or Repeated Start/stop condition de-asserts the SCL pin (SCL allowed to float high). When the SCL pin is allowed to float high, the baud rate generator (BRG) is suspended from counting until the SCL pin is actually sampled high. When the SCL pin is sampled high, the baud rate generator is reloaded with the contents of SSPADD<6:0> and begins counting. This ensures that the SCL high time will always be at least one BRG rollover count in the event that the clock is held low by an external device (Figure 17-33). Figure 17-33: Clock Arbitration Timing in Master Transmit Mode BRG overflow, Release SCL, If SCL = 1 Load BRG with SSPADD<6:0>, and start count to measure high time interval BRG overflow occurs, Release SCL, Slave device holds SCL low. SCL = 1 BRG starts counting clock high interval. SCL SCL line sampled once every machine cycle (Tosc * 4). Hold off BRG until SCL is sampled high. SDA TBRG 17.4.16 TBRG TBRG Sleep Operation While in sleep mode, the I2C module can receive addresses or data, and when an address match or complete byte transfer occurs wake the processor from sleep (if the MSSP interrupt is enabled). 17.4.17 Effect of a Reset A reset disables the MSSP module and terminates the current transfer. DS31017A-page 17-48 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.18 Multi -Master Communication, Bus Collision, and Bus Arbitration Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data bits onto the SDA pin, arbitration takes place when the master outputs a '1' on SDA by letting SDA float high and another master asserts a '0'. When the SCL pin floats high, data should be stable. If the expected data on SDA is a '1' and the data sampled on the SDA pin = '0', then a bus collision has taken place. The master will set the Bus Collision Interrupt Flag, BCLIF and reset the I2C port to its IDLE state. (Figure 17-34). If a transmit was in progress when the bus collision occurred, the transmission is halted, the BF flag is cleared, the SDA and SCL lines are de-asserted, and the SSPBUF can be written to. When the user services the bus collision interrupt service routine, and if the I2C bus is free, the user can resume communication by asserting a START condition. The Master will continue to monitor the SDA and SCL pins, and if a STOP condition occurs, the SSPIF bit will be set. A write to the SSPBUF will start the transmission of data at the first data bit, regardless of where the transmitter left off when bus collision occurred. In multi-master mode, the interrupt generation on the detection of start and stop conditions allows the determination of when the bus is free. Control of the I2C bus can be taken when the P bit is set in the SSPSTAT register, or the bus is idle and the S and P bits are cleared. Figure 17-34: Bus Collision Timing for Transmit and Acknowledge Data changes while SCL = 0 SDA line pulled low by another source SDA released by master Sample SDA. While SCL is high data doesn't match what is driven by the master. Bus collision has occurred. SDA SCL Set bus collision interrupt (BCLIF). BCLIF 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-49 17 MSSP If a START, Repeated Start, STOP, or Acknowledge condition was in progress when the bus collision occurred, the condition is aborted, the SDA and SCL lines are de-asserted, and the respective control bits in the SSPCON2 register are cleared. When the user services the bus collision interrupt service routine, and if the I2C bus is free, the user can resume communication by asserting a START condition. PICmicro MID-RANGE MCU FAMILY 17.4.18.1 Bus Collision During a START Condition During a START condition, a bus collision occurs if: a) b) SDA or SCL are sampled low at the beginning of the START condition (Figure 17-35). SCL is sampled low before SDA is asserted low (Figure 17-36). During a START condition both the SDA and the SCL pins are monitored. If: the SDA pin is already low or the SCL pin is already low, then: the START condition is aborted, and the BCLIF flag is set, and the SSP module is reset to its IDLE state (Figure 17-35). The START condition begins with the SDA and SCL pins de-asserted. When the SDA pin is sampled high, the baud rate generator is loaded from SSPADD<6:0> and counts down to 0. If the SCL pin is sampled low while SDA is high, a bus collision occurs, because it is assumed that another master is attempting to drive a data '1' during the START condition. If the SDA pin is sampled low during this count, the BRG is reset and the SDA line is asserted early (Figure 17-37). If however a '1' is sampled on the SDA pin, the SDA pin is asserted low at the end of the BRG count. The baud rate generator is then reloaded and counts down to 0, and during this time, if the SCL pins is sampled as '0', a bus collision does not occur. At the end of the BRG count the SCL pin is asserted low. Note: DS31017A-page 17-50 The reason that bus collision is not a factor during a START condition is that no two bus masters can assert a START condition at the exact same time. Therefore, one master will always assert SDA before the other. This condition does not cause a bus collision because the two masters must be allowed to arbitrate the first address following the START condition, and if the address is the same, arbitration must be allowed to continue into the data portion, Repeated Start, or STOP conditions. Preliminary 1997 Microchip Technology Inc. Section 17. MSSP Figure 17-35: Bus Collision During Start Condition (SDA only) SDA goes low before the SEN bit is set. . Set BCLIF, S bit and SSPIF set because SDA = 0, SCL = 1 SDA SCL Set SEN, enable start condition if SDA = 1, SCL=1 SEN cleared automatically because of bus collision. SSP module reset into idle state. 17 SEN BCLIF SSPIF and BCLIF are cleared in software. S SSPIF SSPIF and BCLIF are cleared in software. Figure 17-36: Bus Collision During Start Condition (SCL = 0) SDA = 0, SCL = 1 TBRG TBRG SDA Set SEN, enable start sequence if SDA = 1, SCL = 1 SCL SCL = 0 before SDA = 0, Bus collision occurs, Set BCLIF. SEN SCL = 0 before BRG time out, Bus collision occurs, Set BCLIF. BCLIF Interrupts cleared in software. S '0' '0' SSPIF '0' '0' 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-51 MSSP SDA sampled low before START condition. Set BCLIF. S bit and SSPIF set because SDA = 0, SCL = 1 PICmicro MID-RANGE MCU FAMILY Figure 17-37: BRG Reset Due to SDA Arbitration During Start Condition SDA = 0, SCL = 1 Set S Less than TBRG SDA SDA pulled low by other master. Reset BRG and assert SDA SCL S SCL pulled low after BRG Timeout SEN BCLIF Set SSPIF TBRG Set SEN, enable start sequence if SDA = 1, SCL = 1 S SSPIF SDA = 0, SCL = 1 Set SSPIF DS31017A-page 17-52 Preliminary Interrupts cleared in software. 1997 Microchip Technology Inc. Section 17. MSSP 17.4.18.2 Bus Collision During a Repeated Start Condition During a Repeated Start condition, a bus collision occurs if: a) b) A low level is sampled on SDA when SCL goes from low level to high level. SCL goes low before SDA is asserted low, indicating that another master is attempting to transmit a data '1'. When the user de-asserts SDA and the pin is allowed to float high, the BRG is loaded with SSPADD<6:0>, and counts down to zero. The SCL pin is then de-asserted, and when sampled high, the SDA pin is sampled. If SDA is low, a bus collision has occurred (i.e. another master, Figure 17-38, is attempting to transmit a data '0'). If, however, SDA is sampled high then the BRG is reloaded and begins counting. If SDA goes from high to low before the BRG times out, no bus collision occurs, because no two masters can assert SDA at exactly the same time. If, however, SCL goes from high to low before the BRG times out and SDA has not already been asserted, then a bus collision occurs. In this case, another master is attempting to transmit a data '1' during the Repeated Start condition, Figure 17-39. Figure 17-38: Bus Collision During a Repeated Start Condition (Case 1) SDA SCL Sample SDA when SCL goes high. If SDA = 0, set BCLIF and release SDA and SCL RSEN BCLIF Cleared in software '0' S '0' SSPIF 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-53 MSSP If at the end of the BRG time out both SCL and SDA are still high, the SDA pin is driven low, the BRG is reloaded, and begins counting. At the end of the count, regardless of the status of the SCL pin, the SCL pin is driven low and the Repeated Start condition is complete. 17 PICmicro MID-RANGE MCU FAMILY Figure 17-39: Bus Collision During Repeated Start Condition (Case 2) TBRG TBRG SDA SCL BCLIF SCL goes low before SDA, Set BCLIF. Release SDA and SCL Interrupt cleared in software RSEN '0' S SSPIF '0' DS31017A-page 17-54 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.4.18.3 Bus Collision During a STOP Condition Bus collision occurs during a STOP condition if: a) b) After the SDA pin has been de-asserted and allowed to float high, SDA is sampled low after the BRG has timed out. After the SCL pin is de-asserted, SCL is sampled low before SDA goes high. The STOP condition begins with SDA asserted low. When SDA is sampled low, the SCL pin is allow to float. When the pin is sampled high (clock arbitration), the baud rate generator is loaded with SSPADD<6:0> and counts down to 0. After the BRG times out SDA is sampled. If SDA is sampled low, a bus collision has occurred. This is due to another master attempting to drive a data '0' (Figure 17-40). If the SCL pin is sampled low before SDA is allowed to float high, a bus collision occurs. This is another case of another master attempting to drive a data '0' (Figure 17-41). 17 Figure 17-40: Bus Collision During a STOP Condition (Case 1) TBRG SDA sampled low after TBRG, Set BCLIF TBRG SDA SDA asserted low SCL PEN BCLIF P '0' SSPIF '0' Figure 17-41: Bus Collision During a STOP Condition (Case 2) TBRG TBRG TBRG SDA SCL goes low before SDA goes high Set BCLIF Assert SDA SCL PEN BCLIF P '0' SSPIF '0' 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-55 MSSP TBRG PICmicro MID-RANGE MCU FAMILY 17.5 Connection Considerations for I2C Bus For standard-mode I2C bus devices, the values of resistors RP and RS in Figure 17-42 depends on the following parameters: * Supply voltage * Bus capacitance * Number of connected devices (input current + leakage current) The supply voltage limits the minimum value of resistor RP due to the specified minimum sink current of 3 mA at VOLMAX = 0.4V for the specified output stages. For example, with a supply voltage of VDD = 5V+10% and VOLMAX = 0.4V at 3 mA, RPMIN = (5.5-0.4)/0.003 = 1.7 k. VDD as a function of RP is shown in Figure 17-42. The desired noise margin of 0.1VDD for the low level, limits the maximum value of RS. Series resistors are optional, and used to improve ESD susceptibility. The bus capacitance is the total capacitance of wire, connections, and pins. This capacitance limits the maximum value of RP due to the specified rise time (Figure 17-42). The SMP bit is the slew rate control enabled bit. This bit is in the SSPSTAT register, and controls the slew rate of the I/O pins when in I2C mode (master or slave). Figure 17-42: Sample Device Configuration for I2C Bus VDD + 10% RP DEVICE RP RS RS SDA SCL CB = 10 - 400 pF NOTE: I2C devices with input levels related to VDD must have one common supply line to which the pull up resistor is also connected. DS31017A-page 17-56 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.6 Initialization Example 17-2: CLRF CLRF BSF MOVLW MOVWF STATUS ; SSPSTAT ; SSPSTAT, CKE ; 0x31 ; SSPCON ; ; STATUS, RP0 ; PIE, SSPIE ; STATUS, RP0 ; INTCON, GIE ; DataByte ; ; SSPBUF ; BSF BSF BCF BSF MOVLW MOVWF Bank 0 SMP = 0, CKE = 0, and clear status bits CKE = 1 Set up SPI port, Master mode, CLK/16, Data xmit on falling edge (CKE=1 & CKP=1) Data sampled in middle (SMP=0 & Master mode) Bank 1 Enable SSP interrupt Bank 0 Enable, enabled interrupts Data to be Transmitted Could move data from RAM location Start Transmission Master SSP Module / Basic SSP Module Compatibility When changing from the SPI in the Basic SSP module, the SSPSTAT register contains two additional control bits. These bits are: * SMP, SPI data input sample phase * CKE, SPI Clock Edge Select To be compatible with the SPI of the Master SSP module, these bits must be appropriately configured. If these bits are not at the states shown in Table 17-4, improper SPI communication may occur. Table 17-4: New bit States for Compatibility Basic SSP Module 1997 Microchip Technology Inc. Master SSP Module CKP CKP CKE SMP 1 0 1 0 0 0 0 0 Preliminary 17 MSSP 17.6.1 SPI Master Mode Initialization DS31017A-page 17-57 PICmicro MID-RANGE MCU FAMILY 17.7 Design Tips Question 1: Using SPI mode, I do not seem able to talk to an SPI device. Answer 1: Ensure that you are using the correct SPI mode for that device. This SPI supports all 4 SPI modes so you should be able to get it to function. Check the clock polarity and the clock phase. Question 2: Using I2C mode, I write data to the SSPBUF register, but the data did not transmit. Answer 2: Ensure that you set the CKP bit to release the I2C clock. DS31017A-page 17-58 Preliminary 1997 Microchip Technology Inc. Section 17. MSSP 17.8 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Master SSP module are: Title Application Note # Use of the SSP Module in the I 2C Multi-Master Environment. AN578 Using Microchip 93 Series Serial EEPROMs with Microcontroller SPI Ports AN613 Interfacing PIC16C64/74 to Microchip SPI Serial EEPROM AN647 Interfacing a Microchip PIC16C92x to Microchip SPI Serial EEPROM AN668 17 MSSP 1997 Microchip Technology Inc. Preliminary DS31017A-page 17-59 PICmicro MID-RANGE MCU FAMILY 17.9 Revision History Revision A This is the initial released revision of the Master SSP module description. DS31017A-page 17-60 1997 Microchip Technology Inc. M Section 18. USART HIGHLIGHTS This section of the manual contains the following major topics: 18.1 Introduction ..................................................................................................................18-2 18.2 Control Registers .........................................................................................................18-3 18.3 USART Baud Rate Generator (BRG)...........................................................................18-5 18.4 USART Asynchronous Mode .......................................................................................18-8 18.5 USART Synchronous Master Mode ...........................................................................18-15 18.6 USART Synchronous Slave Mode .............................................................................18-19 18.7 Initialization ................................................................................................................18-21 18.8 Design Tips ................................................................................................................18-22 18.9 Related Application Notes..........................................................................................18-23 18.10 Revision History .........................................................................................................18-24 18 USART 1997 Microchip Technology Inc. DS31018A page 18-1 PICmicro MID-RANGE MCU FAMILY 18.1 Introduction The Universal Synchronous Asynchronous Receiver Transmitter (USART) module is one of the two serial I/O modules (other is the SSP module). The USART is also known as a Serial Communications Interface or SCI. The USART can be configured as a full duplex asynchronous system that can communicate with peripheral devices such as CRT terminals and personal computers, or it can be configured as a half duplex synchronous system that can communicate with peripheral devices such as A/D or D/A integrated circuits, Serial EEPROMs etc. The USART can be configured in the following modes: * Asynchronous (full duplex) * Synchronous - Master (half duplex) * Synchronous - Slave (half duplex) The SPEN bit (RCSTA<7>), and the TRIS bits, have to be set in order to configure the TX/CK and RX/DT pins for the USART. DS31018A-page 18-2 1997 Microchip Technology Inc. Section 18. USART 18.2 Control Registers Register 18-1: TXSTA: Transmit Status and Control Register R/W-0 CSRC bit 7 bit 7 R/W-0 TX9 R/W-0 TXEN R/W-0 SYNC U-0 -- R/W-0 BRGH R-1 TRMT R/W-0 TX9D bit 0 CSRC: Clock Source Select bit Asynchronous mode Don't care Synchronous mode 1 = Master mode (Clock generated internally from BRG) 0 = Slave mode (Clock from external source) bit 6 TX9: 9-bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission bit 5 TXEN: Transmit Enable bit 1 = Transmit enabled 0 = Transmit disabled Note: bit 4 SREN/CREN overrides TXEN in SYNC mode. SYNC: USART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode Unimplemented: Read as '0' bit 2 BRGH: High Baud Rate Select bit Asynchronous mode 1 = High speed 0 = Low speed USART bit 3 18 Synchronous mode Unused in this mode bit 1 TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full bit 0 TX9D: 9th bit of transmit data. Can be parity bit. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31018A-page 18-3 PICmicro MID-RANGE MCU FAMILY Register 18-2: RCSTA: Receive Status and Control Register R/W-0 SPEN bit 7 R/W-0 RX9 R/W-0 SREN R/W-0 CREN U-0 -- R-0 FERR R-0 OERR bit 7 SPEN: Serial Port Enable bit 1 = Serial port enabled (Configures RX/DT and TX/CK pins as serial port pins) 0 = Serial port disabled bit 6 RX9: 9-bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception bit 5 SREN: Single Receive Enable bit Asynchronous mode Don't care R-0 RX9D bit 0 Synchronous mode - master 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode - slave Unused in this mode bit 4 CREN: Continuous Receive Enable bit Asynchronous mode 1 = Enables continuous receive 0 = Disables continuous receive Synchronous mode 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive bit 3 Unimplemented: Read as '0' bit 2 FERR: Framing Error bit 1 = Framing error (Can be updated by reading RCREG register and receive next valid byte) 0 = No framing error bit 1 OERR: Overrun Error bit 1 = Overrun error (Can be cleared by clearing bit CREN) 0 = No overrun error bit 0 RX9D: 9th bit of received data, can be parity bit. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' DS31018A-page 18-4 - n = Value at POR reset 1997 Microchip Technology Inc. Section 18. USART 18.3 USART Baud Rate Generator (BRG) The BRG supports both the Asynchronous and Synchronous modes of the USART. It is a dedicated 8-bit baud rate generator. The SPBRG register controls the period of a free running 8-bit timer. In asynchronous mode bit BRGH (TXSTA<2>) also controls the baud rate. In synchronous mode bit BRGH is ignored. Table 18-1 shows the formula for computation of the baud rate for different USART modes which only apply in master mode (internal clock). Given the desired baud rate and Fosc, the nearest integer value for the SPBRG register can be calculated using the formula in Table 18-1, where X equals the value in the SPBRG register (0 to 255). From this, the error in baud rate can be determined. Table 18-1: Baud Rate Formula SYNC BRGH = 0 (Low Speed) BRGH = 1 (High Speed) (Asynchronous) Baud Rate = FOSC/(64(X+1)) (Synchronous) Baud Rate = FOSC/(4(X+1)) X = value in SPBRG (0 to 255) 0 1 Baud Rate= FOSC/(16(X+1)) NA Example 18-1 shows the calculation of the baud rate error for the following conditions: FOSC = 16 MHz Desired Baud Rate = 9600 BRGH = 0 SYNC = 0 Example 18-1: Calculating Baud Rate Error Desired Baud rate 9600 X 18 Fosc / (64 (X + 1)) 16000000 / (64 (X + 1)) 25.042 = 25 Calculated Baud Rate = = 16000000 / (64 (25 + 1)) 9615 Error (Calculated Baud Rate - Desired Baud Rate) Desired Baud Rate (9615 - 9600) / 9600 0.16% = = = USART = = = It may be advantageous to use the high baud rate (BRGH = 1) even for slower baud clocks. This is because the FOSC / (16(X + 1)) equation can reduce the baud rate error in some cases. Writing a new value to the SPBRG register causes the BRG timer to be reset (or cleared). This ensures the BRG does not wait for a timer overflow before outputting the new baud rate. Table 18-2: Registers Associated with Baud Rate Generator Name TXSTA RCSTA SPBRG Legend: x Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets 0000 -010 CSRC TX9 TXEN SYNC -- BRGH TRMT TX9D 0000 -00x SPEN RX9 SREN CREN -- FERR OERR RX9D 0000 0000 Baud Rate Generator Register = unknown, - = unimplemented read as '0'. Shaded cells are not used by the BRG. 1997 Microchip Technology Inc. 0000 -010 0000 -00x 0000 0000 DS31018A-page 18-5 PICmicro MID-RANGE MCU FAMILY Table 18-3: Baud Rates for Synchronous Mode FOSC = 20 MHz BAUD RATE (Kbps) KBAUD % ERROR SPBRG value (decimal) 16 MHz KBAUD % ERROR SPBRG value (decimal) 10 MHz KBAUD % ERROR SPBRG value (decimal) 7.15909 MHz KBAUD % ERROR SPBRG value (decimal) 0.3 NA - - NA - - NA - - NA - - 1.2 NA - - NA - - NA - - NA - - 2.4 NA - - NA - - NA - - NA - - 9.6 NA - - NA - - 9.766 +1.73 255 9.622 +0.23 185 19.2 19.53 +1.73 255 19.23 +0.16 207 19.23 +0.16 129 19.24 +0.23 92 76.8 76.92 +0.16 64 76.92 +0.16 51 75.76 -1.36 32 77.82 +1.32 22 96 96.15 +0.16 51 95.24 -0.79 41 96.15 +0.16 25 94.20 -1.88 18 300 294.1 -1.96 16 307.69 +2.56 12 312.5 +4.17 7 298.3 -0.57 5 500 500 0 9 500 0 7 500 0 4 NA - - HIGH 5000 - 0 4000 - 0 2500 - 0 1789.8 - 0 LOW 19.53 - 255 15.625 - 255 9.766 - 255 6.991 - 255 FOSC = 5.0688 MHz 4 MHz 3.579545 MHz 1 MHz 32.768 kHz BAUD SPBRG SPBRG SPBRG SPBRG SPBRG RATE value value value value % % % % % KBAUD KBAUD KBAUD value KBAUD (Kbps) KBAUD ERROR ERROR (decimal) ERROR (decimal) ERROR (decimal) ERROR (decimal) (decimal) 0.3 NA - - NA - - NA - - NA - - 0.303 +1.14 26 1.2 NA - - NA - - NA - - 1.202 +0.16 207 1.170 -2.48 6 2.4 NA - - NA - - NA - - 2.404 +0.16 103 NA - - 9.6 9.6 0 131 9.615 +0.16 103 9.622 +0.23 92 9.615 +0.16 25 NA - - 19.2 19.2 0 65 19.231 +0.16 51 19.04 -0.83 46 19.24 +0.16 12 NA - - 76.8 79.2 +3.13 15 76.923 +0.16 12 74.57 -2.90 11 83.34 +8.51 2 NA - - 96 97.48 +1.54 12 1000 +4.17 9 99.43 +3.57 8 NA - - NA - - 300 316.8 +5.60 3 NA - - 298.3 -0.57 2 NA - - NA - - 500 NA - - NA - - NA - - NA - - NA - - HIGH 1267 - 0 100 - 0 894.9 - 0 250 - 0 8.192 - 0 LOW 4.950 - 255 3.906 - 255 3.496 - 255 0.9766 - 255 0.032 - 255 DS31018A-page 18-6 1997 Microchip Technology Inc. Section 18. USART Table 18-4: Baud Rates for Asynchronous Mode (BRGH = 0) FOSC = 20 MHz BAUD RATE (Kbps) KBAUD % ERROR 0.3 1.2 2.4 9.6 19.2 76.8 96 300 500 HIGH LOW NA 1.221 2.404 9.469 19.53 78.13 104.2 312.5 NA 312.5 1.221 +1.73 +0.16 -1.36 +1.73 +1.73 +8.51 +4.17 - 16 MHz SPBRG value % (decimal) KBAUD ERROR 255 129 32 15 3 2 0 0 255 FOSC = 5.0688 MHz BAUD RATE (Kbps) NA 1.202 2.404 9.615 19.23 83.33 NA NA NA 250 0.977 SPBRG value (decimal) 207 103 25 12 2 0 255 +0.16 +0.16 +0.16 +0.16 +8.51 - 4 MHz 10 MHz KBAUD % ERROR SPBRG value (decimal) NA 1.202 2.404 9.766 19.53 78.13 NA NA NA 156.3 0.6104 +0.16 +0.16 +1.73 +1.73 +1.73 - 129 64 15 7 1 0 255 3.579545 MHz SPBRG value (decimal) 7.15909 MHz KBAUD % ERROR SPBRG value (decimal) NA 1.203 2.380 9.322 18.64 NA NA NA NA 111.9 0.437 +0.23 -0.83 -2.90 -2.90 - 92 46 11 5 0 255 1 MHz SPBRG value (decimal) 32.768 kHz SPBRG value (decimal) SPBRG value % (decimal) ERROR % KBAUD ERROR SPBRG % value ERROR (decimal) KBAUD 0.3 0.31 +3.13 255 0.3005 -0.17 207 0.301 +0.23 185 0.300 +0.16 51 0.256 -14.67 1.2 1.2 0 65 1.202 +1.67 51 1.190 -0.83 46 1.202 +0.16 12 NA - - 2.4 2.4 0 32 2.404 +1.67 25 2.432 +1.32 22 2.232 -6.99 6 NA - - 9.6 9.9 +3.13 7 NA - - 9.322 -2.90 5 NA - - NA - - 19.2 19.8 +3.13 3 NA - - 18.64 -2.90 2 NA - - NA - - 76.8 79.2 +3.13 0 NA - - NA - - NA - - NA - - 96 NA - - NA - - NA - - NA - - NA - - 300 NA - - NA - - NA - - NA - - NA - - 500 NA HIGH 79.2 % ERROR KBAUD KBAUD 1 - - NA - - NA - - NA - - NA - - - 0 62.500 - 0 55.93 - 0 15.63 - 0 0.512 - 0 255 3.906 255 0.2185 - 255 0.0610 - 255 0.0020 - 0.3094 - - 255 Table 18-5: Baud Rates for Asynchronous Mode (BRGH = 1) FOSC = 20 MHz BAUD RATE (Kbps) KBAUD 16 MHz SPBRG value (decimal) % ERROR 10 MHz SPBRG value (decimal) % ERROR KBAUD 7.15909 MHz SPBRG value (decimal) % ERROR KBAUD SPBRG value (decimal) % ERROR KBAUD 9.6 9.615 +0.16 129 9.615 +0.16 103 9.615 +0.16 64 9.520 -0.83 46 19.2 19.230 +0.16 64 19.230 +0.16 51 18.939 -1.36 32 19.454 +1.32 22 38.4 37.878 -1.36 32 38.461 +0.16 25 39.062 +1.7 15 37.286 -2.90 11 57.6 56.818 -1.36 21 58.823 +2.12 16 56.818 -1.36 10 55.930 -2.90 7 115.2 113.636 -1.36 10 111.111 -3.55 8 125 +8.51 4 111.860 -2.90 3 250 250 0 4 250 0 3 NA - - NA - - 625 625 0 1 NA - - 625 0 0 NA - - 1250 1250 0 0 NA - - NA - - NA - - FOSC = 5.0688 MHz BAUD RATE (Kbps) 4 MHz 3.579545 MHz SPBRG value (decimal) 1 MHz SPBRG value (decimal) 32.768 kHz SPBRG value (decimal) SPBRG value % (decimal) ERROR % KBAUD ERROR SPBRG % value ERROR (decimal) KBAUD 9.6 9.6 32 NA - - 9.727 +1.32 22 8.928 -6.99 6 NA - - 19.2 18.645 -2.94 16 1.202 +0.17 207 18.643 -2.90 11 20.833 +8.51 2 NA - - 38.4 39.6 +3.12 7 2.403 +0.13 103 37.286 -2.90 5 31.25 -18.61 1 NA - - 57.6 52.8 -8.33 5 9.615 +0.16 25 55.930 -2.90 3 62.5 +8.51 0 NA - - 115.2 105.6 -8.33 2 19.231 +0.16 12 111.860 -2.90 1 NA - - NA - - 250 NA - - NA - - 223.721 -10.51 0 NA - - NA - - 625 NA - - NA - - NA - - NA - - NA - - 1250 NA - - NA - - NA - - NA - - NA - - 0 1997 Microchip Technology Inc. KBAUD % ERROR KBAUD % ERROR KBAUD DS31018A-page 18-7 18 USART LOW KBAUD % ERROR PICmicro MID-RANGE MCU FAMILY 18.4 USART Asynchronous Mode In this mode, the USART uses standard nonreturn-to-zero (NRZ) format (one start bit, eight or nine data bits and one stop bit). The most common data format is 8-bits. An on-chip dedicated 8-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. The USART transmits and receives the LSb first. The USART's transmitter and receiver are functionally independent but use the same data format and baud rate. The baud rate generator produces a clock either x16 or x64 of the bit shift rate, depending on the BRGH bit (TXSTA<2>). Parity is not supported by the hardware, but can be implemented in software (stored as the ninth data bit). Asynchronous mode is stopped during SLEEP. Asynchronous mode is selected by clearing the SYNC bit (TXSTA<4>). The USART Asynchronous module consists of the following important elements: * * * * 18.4.1 Baud Rate Generator Sampling Circuit Asynchronous Transmitter Asynchronous Receiver USART Asynchronous Transmitter The USART transmitter block diagram is shown in Figure 18-1. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the STOP bit has been transmitted from the previous load. As soon as the STOP bit is transmitted, the TSR is loaded with new data from the TXREG register (if available). Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG register is empty and the TXIF flag bit is set. This interrupt can be enabled/disabled by setting/clearing the TXIE enable bit. The TXIF flag bit will be set regardless of the state of the TXIE enable bit and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While the TXIF flag bit indicated the status of the TXREG register, the TRMT bit (TXSTA<1>) shows the status of the TSR register. The TRMT status bit is a read only bit which is set when the TSR register is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. Note 1: The TSR register is not mapped in data memory so it is not available to the user. Note 2: When the TXEN bit is set, the TXIF flag bit will also be set since the transmit buffer is not yet full (still can move transmit data to the TXREG register). Transmission is enabled by setting the TXEN enable bit (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data and the baud rate generator (BRG) has produced a shift clock (Figure 18-1). The transmission can also be started by first loading the TXREG register and then setting the TXEN enable bit. Normally when transmission is first started, the TSR register is empty, so a transfer to the TXREG register will result in an immediate transfer to TSR resulting in an empty TXREG. A back-to-back transfer is thus possible (Figure 18-3). Clearing the TXEN enable bit during a transmission will cause the transmission to be aborted and will reset the transmitter. As a result the TX/CK pin will revert to hi-impedance. In order to select 9-bit transmission, transmit bit, TX9 (TXSTA<6>), should be set and the ninth bit should be written to the TX9D bit (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG register can result in an immediate transfer of the data to the TSR register (if the TSR is empty). In such a case, an incorrect ninth data bit maybe loaded in the TSR register. DS31018A-page 18-8 1997 Microchip Technology Inc. Section 18. USART Figure 18-1: USART Transmit Block Diagram Data Bus 8 TXIF TXREG register TXIE 8 MSb (8) * * * LSb 0 Pin Buffer and Control TSR register TX/CK pin Interrupt Baud Rate CLK TXEN TRMT SPEN SPBRG Baud Rate Generator TX9 TX9D Steps to follow when setting up a Asynchronous Transmission: 1. 2. 3. 4. 5. 6. 7. Asynchronous Master Transmission Write to TXREG BRG output (shift clock) Word 1 TX/CK pin Start Bit Bit 1 Bit 7/8 Stop Bit WORD 1 TXIF bit (Transmit buffer reg. empty flag) TRMT bit (Transmit shift reg. empty flag) Bit 0 WORD 1 Transmit Shift Reg 1997 Microchip Technology Inc. 18 USART Figure 18-2: Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set the BRGH bit. (Subsection 18.3 "USART Baud Rate Generator (BRG)" ) Enable the asynchronous serial port by clearing the SYNC bit and setting the SPEN bit. If interrupts are desired, then set the TXIE, GIE and PEIE bits. If 9-bit transmission is desired, then set the TX9 bit. Enable the transmission by setting the TXEN bit, which will also set the TXIF bit. If 9-bit transmission is selected, the ninth bit should be loaded in the TX9D bit. Load data to the TXREG register (starts transmission). DS31018A-page 18-9 PICmicro MID-RANGE MCU FAMILY Figure 18-3: Asynchronous Master Transmission (Back to Back) Write to TXREG BRG output (shift clock) Word 1 TX/CK pin Start Bit TXIF bit (interrupt reg. flag) TRMT bit (Transmit shift reg. empty flag) Word 2 Bit 0 Bit 1 WORD 1 Bit 7/8 Stop Bit Start Bit Bit 0 WORD 2 WORD 1 Transmit Shift Reg. WORD 2 Transmit Shift Reg. Note: This timing diagram shows two consecutive transmissions. Table 18-6: Registers Associated with Asynchronous Transmission Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PIR TXIF (1) RCSTA SPEN RX9 SREN CREN -- FERR OERR TX7 TX6 TX5 TX4 TX3 TX2 TX1 TXREG PIE TXIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH TRMT SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for Asynchronous Transmission. Note 1: The position of this bit is device dependent. DS31018A-page 18-10 Bit 0 RX9D TX0 TX9D Value on: POR, BOR Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 1997 Microchip Technology Inc. Section 18. USART 18.4.2 USART Asynchronous Receiver The receiver block diagram is shown in Figure 18-4. The data is received on the RX/DT pin and drives the data recovery block. The data recovery block is actually a high speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at FOSC. Once Asynchronous mode is selected, reception is enabled by setting the CREN bit (RCSTA<4>). The heart of the receiver is the receive (serial) shift register (RSR). After sampling the RX/TX pin for the STOP bit, the received data in the RSR is transferred to the RCREG register (if it is empty). If the transfer is complete, the RCIF flag bit is set. The actual interrupt can be enabled/disabled by setting/clearing the RCIE enable bit. The RCIF flag bit is a read only bit which is cleared by the hardware. It is cleared when the RCREG register has been read and is empty. The RCREG is a double buffered register, i.e. it is a two deep FIFO. It is possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte begin shifting to the RSR register. On the detection of the STOP bit of the third byte, if the RCREG register is still full then overrun error bit, OERR (RCSTA<1>), will be set. The word in the RSR will be lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. The OERR bit has to be cleared in software. This is done by resetting the receive logic (the CREN bit is cleared and then set). If the OERR bit is set, transfers from the RSR register to the RCREG register are inhibited, so it is essential to clear the OERR bit if it is set. Framing error bit, FERR (RCSTA<2>), is set if a stop bit is detected as a low level. The FERR bit and the 9th receive bit are buffered the same way as the receive data. Reading the RCREG will load the RX9D and FERR bits with new values, therefore it is essential for the user to read the RCSTA register before reading the next RCREG register in order not to lose the old (previous) information in the FERR and RX9D bits. Figure 18-4: USART Receive Block Diagram USART x64 Baud Rate CLK FERR OERR CREN SPBRG RSR register MSb Baud Rate Generator Stop (8) 7 * * * 1 LSb 0 Start RX/DT Pin Buffer and Control Data Recovery RX9 RX9D SPEN RCREG register FIFO 8 Interrupt RCIF Data Bus RCIE 1997 Microchip Technology Inc. 18 DS31018A-page 18-11 PICmicro MID-RANGE MCU FAMILY Steps to follow when setting up an Asynchronous Reception: 1. 2. 3. 4. 5. 6. 7. 8. 9. Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. (Subsection 18.3 "USART Baud Rate Generator (BRG)" ). Enable the asynchronous serial port by clearing the SYNC bit, and setting the SPEN bit. If interrupts are desired, then set the RCIE, GIE and PEIE bits. If 9-bit reception is desired, then set the RX9 bit. Enable the reception by setting the CREN bit. The RCIF flag bit will be set when reception is complete and an interrupt will be generated if the RCIE bit was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing the CREN bit. Figure 18-5: RX (pin) Rcv shift reg Rcv buffer reg Read Rcv buffer reg RCREG Start bit bit0 bit1 Asynchronous Reception bit7/8 Stop bit Start bit WORD 1 RCREG bit0 bit7/8 Stop bit Start bit bit7/8 Stop bit WORD 2 RCREG RCIF (interrupt flag) OERR bit CREN Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word, causing the OERR (overrun) bit to be set. DS31018A-page 18-12 1997 Microchip Technology Inc. Section 18. USART 18.4.3 Sampling The data on the RX/DT pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the RX pin. Figure 18-6 shows the waveform for the sampling circuit. The sampling operates the same regardless of the state of the BRGH bit, only the source of the x16 clock is different. Figure 18-6: RX Pin Sampling Scheme, BRGH = 0 or BRGH = 1 Start bit RX (RX/DT pin) Bit0 Baud CLK for all but start bit baud CLK x16 CLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 Samples 18.4.3.1 Device Exceptions All new devices will use the sampling scheme shown in Figure 18-6. Devices that have an exception to the above sampling scheme are: PIC16C63 PIC16C65 PIC16C65A PIC16C73 PIC16C73A PIC16C74 PIC16C74A USART * * * * * * * These devices have a sampling circuitry that works as follows. If the BRGH bit (TXSTA<2>) is clear (i.e., at the low baud rates), the sampling is done on the seventh, eighth and ninth falling edges of a x16 clock (Figure 18-7). If bit BRGH is set (i.e., at the high baud rates), the sampling is done on the 3 clock edges preceding the second rising edge after the first falling edge of a x4 clock (Figure 18-8 and Figure 18-9). Figure 18-7: RX Pin Sampling Scheme (BRGH = 0) Start bit RX (RX/DT pin) Bit0 Baud CLK for all but start bit baud CLK x16 CLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 Samples 1997 Microchip Technology Inc. 18 DS31018A-page 18-13 PICmicro MID-RANGE MCU FAMILY Figure 18-8: RX Pin Sampling Scheme (BRGH = 1) RX pin bit0 Start Bit bit1 baud clk First falling edge after RX pin goes low Second rising edge x4 clk 1 2 3 4 1 2 3 4 1 2 Q2, Q4 clk Samples Figure 18-9: Samples Samples RX Pin Sampling Scheme (BRGH = 1) RX pin Start Bit bit0 Baud clk for all but start bit baud clk First falling edge after RX pin goes low Second rising edge x4 clk 1 2 3 4 Q2, Q4 clk Samples Table 18-7: Registers Associated with Asynchronous Reception Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 PIR RCIF (1) RCSTA SPEN RX9 SREN CREN -- FERR RCREG RX7 RX6 RX5 RX4 RX3 RX2 PIE RCIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for Asynchronous Reception. Note 1: The position of this bit is device dependent. DS31018A-page 18-14 Bit 1 Bit 0 OERR RX1 RX9D RX0 TRMT TX9D Value on: POR, BOR Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 1997 Microchip Technology Inc. Section 18. USART 18.5 USART Synchronous Master Mode In Synchronous Master mode, the data is transmitted in a half-duplex manner, i.e. transmission and reception do not occur at the same time. When transmitting data, the reception is inhibited and vice versa. Synchronous mode is entered by setting the SYNC bit (TXSTA<4>). In addition, the SPEN enable bit (RCSTA<7>) is set in order to configure the TX/CK and RX/DT I/O pins to CK (clock) and DT (data) lines respectively. The Master mode indicates that the processor transmits the master clock on the CK line. The Master mode is entered by setting the CSRC bit (TXSTA<7>). 18.5.1 USART Synchronous Master Transmission The USART transmitter block diagram is shown in Figure 18-1. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer register TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the last bit has been transmitted from the previous load. As soon as the last bit is transmitted, the TSR is loaded with new data from the TXREG (if available). Once the TXREG register transfers the data to the TSR register (occurs in one Tcycle), the TXREG is empty and the TXIF interrupt flag bit is set. The interrupt can be enabled/disabled by setting/clearing enable the TXIE bit. The TXIF flag bit will be set regardless of the state of the TXIE enable bit and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While the TXIF flag bit indicates the status of the TXREG register, the TRMT bit (TXSTA<1>) shows the status of the TSR register. The TRMT bit is a read only bit which is set when the TSR is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not mapped in data memory so it is not available to the user. Clearing the TXEN bit during a transmission will cause the transmission to be aborted and will reset the transmitter. The DT and CK pins will revert to hi-impedance. If either of the CREN or SREN bits are set during a transmission, the transmission is aborted and the DT pin reverts to a hi-impedance state (for a reception). The CK pin will remain an output if the CSRC bit is set (internal clock). The transmitter logic is not reset although it is disconnected from the pins. In order to reset the transmitter, the user has to clear the TXEN bit. If the SREN bit is set (to interrupt an on-going transmission and receive a single word), then after the single word is received, the SREN bit will be cleared and the serial port will revert back to transmitting since the TXEN bit is still set. The DT line will immediately switch from hi-impedance receive mode to transmit and start driving. To avoid this the TXEN bit should be cleared. In order to select 9-bit transmission, the TX9 bit (TXSTA<6>) should be set and the ninth bit should be written to the TX9D bit (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG can result in an immediate transfer of the data to the TSR register (if the TSR is empty). If the TSR was empty and the TXREG was written before writing the "new" value to the TX9D bit, the "present" value of of the TX9D bit is loaded. 1997 Microchip Technology Inc. DS31018A-page 18-15 18 USART Transmission is enabled by setting the TXEN bit (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data. The first data bit will be shifted out on the next available rising edge of the clock on the CK line. Data out is stable at the falling edge of the synchronous clock (Figure 18-10). The transmission can also be started by first loading the TXREG register and then setting the TXEN bit. This is advantageous when slow baud rates are selected, since the BRG is kept in reset when the TXEN, CREN, and SREN bits are clear. Setting the TXEN bit will start the BRG, creating a shift clock immediately. Normally when transmission is first started, the TSR register is empty, so a transfer to the TXREG register will result in an immediate transfer to TSR resulting in an empty TXREG. Back-to-back transfers are possible. PICmicro MID-RANGE MCU FAMILY Steps to follow when setting up a Synchronous Master Transmission: 1. 2. 3. 4. 5. 6. 7. Initialize the SPBRG register for the appropriate baud rate (Subsection 18.3 "USART Baud Rate Generator (BRG)" ). Enable the synchronous master serial port by setting the SYNC, SPEN, and CSRC bits. If interrupts are desired, then set the TXIE bit. If 9-bit transmission is desired, then set the TX9 bit. Enable the transmission by setting the TXEN bit. If 9-bit transmission is selected, the ninth bit should be loaded in the TX9D bit. Start transmission by loading data to the TXREG register. Table 18-8: Registers Associated with Synchronous Master Transmission Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PIR TXIF (1) RCSTA SPEN RX9 SREN CREN -- FERR OERR TXREG TX7 TX6 TX5 TX4 TX3 TX2 TX1 PIE TXIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH TRMT SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for Synchronous Master Transmission. Note 1: The position of this bit is device dependent. Figure 18-10: Bit 0 TX9D Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 Synchronous Transmission Q1Q2 Q3Q4 Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2 Q3Q4 RX/DT pin RX9D TX0 Value on: POR, BOR Bit 1 Bit 2 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4 Bit 7 Bit 0 WORD 1 Bit 1 WORD 2 Bit 7 TX/CK pin Write to TXREG reg Write word1 Write word2 TXIF bit (Interrupt flag) TRMT TRMT bit TXEN bit '1' '1' Note: Sync master mode; SPBRG = '0'. Continuous transmission of two 8-bit words. Figure 18-11: RX/DT pin Synchronous Transmission (Through TXEN) bit0 bit1 bit2 bit6 bit7 TX/CK pin Write to TXREG reg TXIF bit TRMT bit DS31018A-page 18-16 1997 Microchip Technology Inc. Section 18. USART 18.5.2 USART Synchronous Master Reception Once Synchronous mode is selected, reception is enabled by setting either of the SREN (RCSTA<5>) or CREN (RCSTA<4>) bits. Data is sampled on the RX/DT pin on the falling edge of the clock. If the SREN bit is set, then only a single word is received. If the CREN bit is set, the reception is continuous until the CREN bit is cleared. If both bits are set then the CREN bit takes precedence. After clocking the last serial data bit, the received data in the Receive Shift Register (RSR) is transferred to the RCREG register (if it is empty). When the transfer is complete, the RCIF interrupt flag bit is set. The actual interrupt can be enabled/disabled by setting/clearing the RCIE enable bit. The RCIF flag bit is a read only bit which is cleared by the hardware. In this case it is cleared when the RCREG register has been read and is empty. The RCREG is a double buffered register, i.e. it is a two deep FIFO. It is possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting into the RSR register. On the clocking of the last bit of the third byte, if the RCREG register is still full then overrun error bit, OERR (RCSTA<1>), is set and the word in the RSR is lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. The OERR bit has to be cleared in software (by clearing the CREN bit). If the OERR bit is set, transfers from the RSR to the RCREG are inhibited, so it is essential to clear the OERR bit if it is set. The 9th receive bit is buffered the same way as the receive data. Reading the RCREG register will load the RX9D bit with a new value, therefore it is essential for the user to read the RCSTA register before reading RCREG in order not to lose the old (previous) information in the RX9D bit. Steps to follow when setting up a Synchronous Master Reception: 1. Table 18-9: Registers Associated with Synchronous Master Reception Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PIR RCIF (1) RCSTA SPEN RX9 SREN CREN -- FERR OERR RCREG RX7 RX6 RX5 RX4 RX3 RX2 RX1 PIE RCIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH TRMT SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for Synchronous Master Reception. Note 1: The position of this bit is device dependent. 1997 Microchip Technology Inc. Bit 0 RX9D RX0 TX9D Value on: POR, BOR Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 DS31018A-page 18-17 18 USART Initialize the SPBRG register for the appropriate baud rate. (Subsection 18.3 "USART Baud Rate Generator (BRG)" ) 2. Enable the synchronous master serial port by setting the SYNC, SPEN, and CSRC bits. 3. Ensure that the CREN and SREN bits are clear. 4. If interrupts are desired, then set the RCIE bit. 5. If 9-bit reception is desired, then set the RX9 bit. 6. If a single reception is required, set the SREN bit. For continuous reception set the CREN bit. 7. The RCIF bit will be set when reception is complete and an interrupt will be generated if the RCIE bit was set. 8. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 9. Read the 8-bit received data by reading the RCREG register. 10. If any error occurred, clear the error by clearing the CREN bit. PICmicro MID-RANGE MCU FAMILY Figure 18-12: Synchronous Reception (Master Mode, SREN) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 DT pin bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 CK pin Write to SREN bit SREN bit '0' CREN bit RCIF bit (interrupt) Read RXREG Note: Timing diagram demonstrates SYNC master mode with SREN = '1' and BRG = '0'. DS31018A-page 18-18 1997 Microchip Technology Inc. Section 18. USART 18.6 USART Synchronous Slave Mode Synchronous slave mode differs from the Master mode in the fact that the shift clock is supplied externally at the TX/CK pin (instead of being supplied internally in master mode). This allows the device to transfer or receive data while in SLEEP mode. Slave mode is entered by clearing the CSRC bit (TXSTA<7>). 18.6.1 USART Synchronous Slave Transmit The operation of the synchronous master and slave modes are identical except in the case of the SLEEP mode. If two words are written to the TXREG and then the SLEEP instruction is executed, the following will occur: a) b) c) d) e) The first word will immediately transfer to the TSR register and transmit. The second word will remain in TXREG register. The TXIF flag bit will not be set. When the first word has been shifted out of TSR, the TXREG register will transfer the second word to the TSR and the TXIF flag bit will now be set. If the TXIE enable bit is set, the interrupt will wake the chip from SLEEP and if the global interrupt is enabled, the program will branch to the interrupt vector (0004h). Steps to follow when setting up a Synchronous Slave Transmission: 1. Table 18-10: Registers Associated with Synchronous Slave Transmission Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PIR TXIF (1) RCSTA SPEN RX9 SREN CREN -- FERR OERR TXREG TX7 TX6 TX5 TX4 TX3 TX2 TX1 PIE TXIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH TRMT SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for Synchronous Slave Transmission. Note 1: The position of this bit is device dependent. 1997 Microchip Technology Inc. Bit 0 RX9D TX0 TX9D Value on: POR, BOR Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 DS31018A-page 18-19 18 USART 2. 3. 4. 5. 6. 7. Enable the synchronous slave serial port by setting the SYNC and SPEN bits and clearing the CSRC bit. Clear the CREN and SREN bits. If interrupts are desired, then set the TXIE enable bit. If 9-bit transmission is desired, then set the TX9 bit. Enable the transmission by setting the TXEN enable bit. If 9-bit transmission is selected, the ninth bit should be loaded into the TX9D bit. Start transmission by loading data to the TXREG register. PICmicro MID-RANGE MCU FAMILY 18.6.2 USART Synchronous Slave Reception The operation of the synchronous master and slave modes is identical except in the case of the SLEEP mode. Also, bit SREN is a don't care in slave mode. If receive is enabled, by setting the CREN bit, prior to the SLEEP instruction, then a word may be received during SLEEP. On completely receiving the word, the RSR register will transfer the data to the RCREG register and if the RCIE enable bit bit is set, the interrupt generated will wake the chip from SLEEP. If the global interrupt is enabled, the program will branch to the interrupt vector (0004h). Steps to follow when setting up a Synchronous Slave Reception: 1. 2. 3. 4. 5. 6. 7. 8. Enable the synchronous master serial port by setting the SYNC and SPEN bits and clearing the CSRC bit. If interrupts are desired, then set the RCIE enable bit. If 9-bit reception is desired, then set the RX9 bit. To enable reception, set the CREN enable bit. The RCIF bit will be set when reception is complete and an interrupt will be generated, if the RCIE bit was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing the CREN bit. Table 18-11: Registers Associated with Synchronous Slave Reception Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PIR RCIF (1) RCSTA SPEN RX9 SREN CREN -- FERR OERR RCREG RX7 RX6 RX5 RX4 RX3 RX2 RX1 PIE RCIE (1) TXSTA CSRC TX9 TXEN SYNC -- BRGH TRMT SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for Synchronous Slave Reception. Note 1: The position of this bit is device dependent. DS31018A-page 18-20 Bit 0 RX9D RX0 TX9D Value on: POR, BOR Value on all other Resets 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 0 0000 -00x 0000 0000 0 0000 -010 0000 0000 1997 Microchip Technology Inc. Section 18. USART 18.7 Initialization Example 18-2 is an initialization routine for asynchronous Transmitter/Receiver mode. Example 18-3 is for the synchronous mode. In both examples the data is 8-bits, and the value to load into the SPBRG register is dependent on the desired baud rate and the device frequency. Example 18-2: BSF MOVLW MOVWF MOVLW MOVWF BSF BSF BCF MOVLW MOVWF STATUS,RP0 SPBRG 0x40 TXSTA PIE1,TXIE PIE1,RCIE STATUS,RP0 0x90 RCSTA Example 18-3: BSF MOVLW MOVWF MOVLW MOVWF BSF BSF BCF MOVLW MOVWF Asynchronous Transmitter/Receiver ; Go to Bank1 ; Set Baud rate ; ; ; ; ; ; ; 8-bit transmit, transmitter enabled, asynchronous mode, low speed mode Enable transmit interrupts Enable receive interrupts Go to Bank 0 8-bit receive, receiver enabled, serial port enabled Synchronous Transmitter/Receiver STATUS,RP0 SPBRG 0xB0 TXSTA PIE1,TXIE PIE1,RCIE STATUS,RP0 0x90 RCSTA ; Go to Bank 1 ; Set Baud Rate ; ; ; ; ; ; ; Synchronous Master,8-bit transmit, transmitter enabled, low speed mode Enable transmit interrupts Enable receive interrupts Go to Bank 0 8-bit receive, receiver enabled, continuous receive, serial port enabled 18 USART 1997 Microchip Technology Inc. DS31018A-page 18-21 PICmicro MID-RANGE MCU FAMILY 18.8 Design Tips Question 1: Using the Asynchronous mode I am getting a lot of transmission errors. Answer 1: The most common reasons are 1. 2. 3. DS31018A-page 18-22 You are using the high speed mode (BRGH is set) on one of the devices which has an errata for this mode (PIC16C65/65A/73/73A/74/74A). You have incorrectly calculated the value to load in to the SPBRG register The sum of the baud errors for the transmitter and receiver is too high. 1997 Microchip Technology Inc. Section 18. USART 18.9 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to this section are: Title Application Note # Serial Port Utilities AN547 Servo Control of a DC Brushless Motor AN543 18 USART 1997 Microchip Technology Inc. DS31018A-page 18-23 PICmicro MID-RANGE MCU FAMILY 18.10 Revision History Revision A This is the initial released revision of the USART module description. DS31018A-page 18-24 1997 Microchip Technology Inc. M Section 19. Voltage Reference HIGHLIGHTS This section of the manual contains the following major topics: 19.1 Introduction ..................................................................................................................19-2 19.2 Control Register ...........................................................................................................19-3 19.3 Configuring the Voltage Reference ..............................................................................19-4 19.4 Voltage Reference Accuracy/Error ...............................................................................19-5 19.5 Operation During Sleep ...............................................................................................19-5 19.6 Effects of a Reset.........................................................................................................19-5 19.7 Connection Considerations ..........................................................................................19-6 19.8 Initialization ..................................................................................................................19-7 19.9 Design Tips ..................................................................................................................19-8 19.10 Related Application Notes............................................................................................19-9 19.11 Revision History .........................................................................................................19-10 19 Voltage Reference 1997 Microchip Technology Inc. DS31019A page 19-1 PICmicro MID-RANGE MCU FAMILY 19.1 Introduction The Voltage Reference module is typically used in conjunction with the Comparator module. The comparator module's inputs do not require very large drive, and therefore the drive capability of the Voltage Reference is limited. The Voltage Reference is a 16-tap resistor ladder network that provides a selectable voltage reference. The resistor ladder is segmented to provide two ranges of VREF values and has a power-down function to conserve power when the reference is not being used. The VRCON register controls the operation of the reference as shown in Figure 19-1. The block diagram is given in Figure 19-1. Within each range, the 16 steps are monotonic (i.e. each increasing code will result in an increasing output). Figure 19-1: Voltage Reference Block Diagram 16 Stages VREN 8R(1) R(1) R(1) R(1) R(1) 8R(1) VRR VR3 VREF (From VRCON<3:0>) 16-1 Analog MUX VR0 Note 1: See parameter D312 in the Electrical Specifications section of the device data sheet. Table 19-1: Typical Voltage Reference with VDD = 5.0V VREF VR3:VR0 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 DS31019A-page 19-2 VRR = 1 VRR = 0 0.00 V 0.21 V 0.42 V 0.63 V 0.83 V 1.04 V 1.25 V 1.46 V 1.67 V 1.88 V 2.08 V 2.29 V 2.50 V 2.71 V 2.92 V 3.13 V 1.25 V 1.41 V 1.56 V 1.72 V 1.88 V 2.03 V 2.19 V 2.34 V 2.50 V 2.66 V 2.81 V 2.97 V 3.13 V 3.28 V 3.44 V 3.59 V 1997 Microchip Technology Inc. Section 19. Voltage Reference 19.2 Control Register Register 19-1: VRCON Register R/W-0 VREN bit 7 R/W-0 VROE R/W-0 VRR U-0 -- R/W-0 VR3 R/W-0 VR2 R/W-0 VR1 R/W-0 VR0 bit 0 bit 7 VREN: VREF Enable 1 = VREF circuit powered on 0 = VREF circuit powered down bit 6 VROE: VREF Output Enable 1 = VREF is internally connected to Comparator module's VREF. This voltage level is also output on the VREF pin 0 = VREF is not connected to the comparator module. This voltage is disconnected from the VREF pin bit 5 VRR: VREF Range selection 1 = 0V to 0.75 VDD, with VDD/24 step size 0 = 0.25 VDD to 0.75 VDD, with VDD/32 step size bit 4 Unimplemented: Read as '0' bit 3:0 VR3:VR0: VREF value selection 0 VR3:VR0 15 When VRR = 1: VREF = (VR<3:0>/ 24) * VDD When VRR = 0: VREF = 1/4 * VDD + (VR3:VR0/ 32) * VDD Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 19 Voltage Reference 1997 Microchip Technology Inc. DS31019A-page 19-3 PICmicro MID-RANGE MCU FAMILY 19.3 Configuring the Voltage Reference The Voltage Reference can output 16 distinct voltage levels for each range. The equations used to calculate the output of the Voltage Reference are as follows: if VRR = 1: VREF = (VR3:VR0/24) x VDD if VRR = 0: VREF = (VDD x 1/4) + (VR3:VR0/32) x VDD The settling time of the Voltage Reference must be considered when changing the VREF output. Example 19-1 shows an example of how to configure the Voltage Reference for an output voltage of 1.25V with VDD = 5.0V. Generally the VREF and VDD of the system will be known and you need to determine the value to load into VR3:VR0. Equation 19-1 shows how to calculate the VR3:VR0 value. There will be some error since VR3:VR0 can only be an integer, and the VREF and VDD levels must be chosen so that the result is not greater then 15. Equation 19-1: Calculating VR3:VR0 When VRR = 1 VR3:VR0 = VREF VDD VR3:VR0 = VREF - VDD/4 VDD X 24 When VRR = 0 DS31019A-page 19-4 X 32 1997 Microchip Technology Inc. Section 19. Voltage Reference 19.4 Voltage Reference Accuracy/Error The full range of VSS to VDD cannot be realized due to the construction of the module. The transistors on the top and bottom of the resistor ladder network (Figure 19-1) keep VREF from approaching VSS or VDD. The Voltage Reference is VDD derived and therefore, the VREF output changes with fluctuations in VDD. The absolute accuracy of the Voltage Reference can be found in the Device Data Sheets electrical specification parameter D311. 19.5 Operation During Sleep When the device wakes up from sleep through an interrupt or a Watchdog Timer time-out, the contents of the VRCON register are not affected. To minimize current consumption in SLEEP mode, the Voltage Reference should be disabled. 19.6 Effects of a Reset A device reset disables the Voltage Reference by clearing the VREN bit (VRCON<7>). This reset also disconnects the reference from the VREF pin by clearing the VROE bit (VRCON<6>) and selects the high voltage range by clearing the VRR bit (VRCON<5>). The VREF value select bits, VRCON<3:0>, are also cleared. 19 Voltage Reference 1997 Microchip Technology Inc. DS31019A-page 19-5 PICmicro MID-RANGE MCU FAMILY 19.7 Connection Considerations The Voltage Reference Module operates independently of the comparator module. The output of the reference generator may be connected to the VREF pin if the corresponding TRIS bit is set and the VROE bit (VRCON<6>) is set. Enabling the Voltage Reference output onto the VREF pin with an input signal present will increase current consumption. Configuring the VREF as a digital output with VREF enabled will also increase current consumption. The VREF pin can be used as a simple D/A output with limited drive capability. Due to the limited drive capability, a buffer must be used in conjunction with the Voltage Reference output for external connections to VREF. Figure 19-2 shows an example buffering technique. Figure 19-2: Voltage Reference Output Buffer Example VREF Module R(1) ANx * + - * VREF Output PIC16CXXX Note 1: R is the Voltage Reference Output Impedance and is dependent upon the Voltage Reference Configuration VRCON<3:0> and VRCON<5>. DS31019A-page 19-6 1997 Microchip Technology Inc. Section 19. Voltage Reference 19.8 Initialization Example 19-1 shows the steps to configure the voltage reference module. Example 19-1: MOVLW MOVWF BSF MOVLW MOVWF MOVLW MOVWF BCF CALL Voltage Reference Configuration 0x02 CMCON STATUS,RP0 0x07 TRISA 0xA6 VRCON STATUS,RP0 DELAY10 ; ; ; ; ; ; ; ; ; 4 Inputs Muxed to 2 comparators go to Bank1 RA3:RA0 are outputs outputs enable VREF low range set VR3:VR0 = 6 go to Bank0 10 s delay 19 Voltage Reference 1997 Microchip Technology Inc. DS31019A-page 19-7 PICmicro MID-RANGE MCU FAMILY 19.9 Design Tips Question 1: My VREF is not what I expect. Answer 1: Any variation of the device VDD will translate directly onto the VREF pin. Also ensure that you have correctly calculated (specified) the VDD divider which generates the VREF. Question 2: I am connecting VREF into a low impedance circuit, and the VREF is not at the expected level. Answer 2: The Voltage Reference module is not intended to drive large loads. A buffer must be used between the PICmicro's VREF pin and the load. DS31019A-page 19-8 1997 Microchip Technology Inc. Section 19. Voltage Reference 19.10 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Voltage Reference are: Title Resistance and Capacitance Meter using a PIC16C622 Application Note # AN611 19 Voltage Reference 1997 Microchip Technology Inc. DS31019A-page 19-9 PICmicro MID-RANGE MCU FAMILY 19.11 Revision History Revision A This is the initial released revision of the Voltage Reference description. DS31019A-page 19-10 1997 Microchip Technology Inc. M Section 20. Comparator HIGHLIGHTS This section of the manual contains the following major topics: 20.1 Introduction ..................................................................................................................20-2 20.2 Control Register ...........................................................................................................20-3 20.3 Comparator Configuration............................................................................................20-4 20.4 Comparator Operation .................................................................................................20-6 20.5 Comparator Reference.................................................................................................20-6 20.6 Comparator Response Time ........................................................................................20-8 20.7 Comparator Outputs ....................................................................................................20-8 20.8 Comparator Interrupts..................................................................................................20-9 20.9 Comparator Operation During SLEEP .........................................................................20-9 20.10 Effects of a RESET ......................................................................................................20-9 20.11 Analog Input Connection Considerations...................................................................20-10 20.12 Initialization ................................................................................................................20-11 20.13 Design Tips ................................................................................................................20-12 20.14 Related Application Notes..........................................................................................20-13 20.15 Revision History .........................................................................................................20-14 20 Comparator 1997 Microchip Technology Inc. DS31020A page 20-1 PICmicro MID-RANGE MCU FAMILY 20.1 Introduction The comparator module contains two analog comparators. The inputs to the comparators are multiplexed with the I/O pins. The on-chip Voltage Reference (see the "Voltage Reference" section) can also be an input to the comparators. The CMCON register, shown in Figure 20-1, controls the comparator input and output multiplexers. A block diagram of the comparator is shown in Figure 20-1. DS31020A-page 20-2 1997 Microchip Technology Inc. Section 20. Comparator 20.2 Control Register Register 20-1: CMCON Register R-0 C2OUT bit 7 R-0 C1OUT U-0 -- U-0 -- bit 7 C2OUT: Comparator2 Output Indicator bit 1 = C2 VIN+ > C2 VIN- 0 = C2 VIN+ < C2 VIN- bit 6 C1OUT: Comparator1 Output Indicator bit 1 = C1 VIN+ > C1 VIN- 0 = C1 VIN+ < C1 VIN- bit 5:4 Unimplemented: Read as '0' bit 3 CIS: Comparator Input Switch bit R/W-0 CIS R/W-0 CM2 R/W-0 CM1 R/W-0 CM0 bit 0 When CM2:CM0: = 001: 1 = C1 VIN- connects to AN3 0 = C1 VIN- connects to AN0 When CM2:CM0 = 010: 1 = C1 VIN- connects to AN3 C2 VIN- connects to AN2 0 = C1 VIN- connects to AN0 C2 VIN- connects to AN1 bit 2:0 CM2:CM0: Comparator Mode Select bits See Figure 20-1. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 20 Comparator 1997 Microchip Technology Inc. DS31020A-page 20-3 PICmicro MID-RANGE MCU FAMILY 20.3 Comparator Configuration There are eight modes of operation for the comparators. The CMCON register is used to select the mode. Figure 20-1 shows the eight possible modes. The TRIS register controls the data direction of the comparator I/O pins for each mode. If the comparator mode is changed, the comparator output level may not be valid for the new mode for the delay specified in the electrical specifications of the device. Note: DS31020A-page 20-4 Comparator interrupts should be disabled during a comparator mode change, otherwise a false interrupt may occur. 1997 Microchip Technology Inc. Section 20. Comparator Figure 20-1: Comparator I/O Operating Modes CM2:CM0 = 000 Comparators Reset (POR Default Value) RA0/AN0 RA3/AN3 RA1/AN1 RA2/AN2 A VIN- A VIN+ A VIN- A VIN+ RA0/AN0 C1 Off (Read as '0') RA3/AN3 A VIN- A VIN+ A VIN- RA3/AN3 RA1/AN1 C2 Off (Read as '0') CM2:CM0 = 100 Two Independent Comparators RA0/AN0 CM2:CM0 = 111 Comparators Off RA2/AN2 C1OUT RA3/AN3 RA1/AN1 RA1/AN1 RA2/AN2 A VIN+ C2 VIN- D VIN+ D VIN- D VIN+ C1 Off (Read as '0') C2 Off (Read as '0') CM2:CM0 = 010 Four Inputs Multiplexed to Two Comparators RA0/AN0 C1 D C2OUT RA2/AN2 A A VIN- CIS = 0 CIS = 1 VIN+ C1 C1OUT C2 C2OUT A A VIN- CIS = 0 CIS = 1 VIN+ From VREF Module CM2:CM0 = 110 Two Common Reference Comparators with Outputs CM2:CM0 = 011 Two Common Reference Comparators RA0/AN0 RA3/AN3 RA1/AN1 RA2/AN2 A VIN- D VIN+ A VIN- A VIN+ RA0/AN0 C1 C1OUT RA3/AN3 RA1/AN1 C2 C2OUT RA2/AN2 A VIN- D VIN+ A VIN- A VIN+ C1 C1OUT C2 C2OUT RA4 Open Drain CM2:CM0 = 101 One Independent Comparator RA0/AN0 RA3/AN3 RA1/AN1 RA2/AN2 D VIN- D VIN+ A VIN- A VIN+ CM2:CM0 = 001 Three Inputs Multiplexed to Two Comparators RA0/AN0 C1 Off (Read as '0') RA3/AN3 RA1/AN1 C2 C2OUT RA2/AN2 A A CIS = 0 CIS = 1 VINVIN+ A VIN- A VIN+ C1 C1OUT C2 C2OUT Comparator A = Analog Input, port reads as zeros always. D = Digital Input. CIS (CMCON<3>) is the Comparator Input Switch. 1997 Microchip Technology Inc. 20 DS31020A-page 20-5 PICmicro MID-RANGE MCU FAMILY 20.4 Comparator Operation A single comparator is shown in Figure 20-2 along with the relationship between the analog input levels and the digital output. When the analog input at VIN+ is less than the analog input VIN-, the output of the comparator is a digital low level. When the analog input at VIN+ is greater than the analog input VIN-, the output of the comparator is a digital high level. The shaded areas of the output of the comparator in Figure 20-2 represent the uncertainty due to input offsets and response time. 20.5 Comparator Reference An external or internal reference signal may be used depending on the comparator operating mode. The analog signal that is present at VIN- is compared to the signal at VIN+, and the digital output of the comparator is adjusted accordingly (Figure 20-2). Figure 20-2: Single Comparator VIN+ + VIN- - Output VIN- VIN+ Output DS31020A-page 20-6 1997 Microchip Technology Inc. Section 20. Comparator 20.5.1 External Reference Signal When external voltage references are used, the comparator module can be configured to have the comparators operate from the same or different reference sources. The reference signal must be between VSS and VDD, and can be applied to either pin of the comparator(s). 20.5.2 Internal Reference Signal The comparator module also allows the selection of an internally generated voltage reference for the comparators. The "Voltage Reference" section contains a detailed description of the Voltage Reference Module that provides this signal. The internal reference signal is used when the comparators are in mode CM2:CM0 = 010 (Figure 20-1). In this mode, the internal voltage reference is applied to the VIN+ input of both comparators. The internal voltage reference may be used in any comparator mode. When used in this fashion the I/O/VREF pin may be used for I/O. The voltage reference is connected to the VREF pin. 20 Comparator 1997 Microchip Technology Inc. DS31020A-page 20-7 PICmicro MID-RANGE MCU FAMILY 20.6 Comparator Response Time Response time is the minimum time, after selecting a new reference voltage or input source, before the comparator output is guaranteed to have a valid level. If the internal reference is changed, the maximum settling time of the internal voltage reference must be considered when using the comparator outputs. Otherwise the maximum response time of the comparators should be used. 20.7 Comparator Outputs The comparator outputs are read through the CMCON register. These bits are read only. The comparator outputs may also be directly output to the I/O pins. When CM2:CM0 = 110, multiplexors in the output path of the I/O pins will switch and the output of each pin will be the unsynchronized output of the comparator. The uncertainty of each of the comparators is related to the input offset voltage and the response time given in the specifications. Figure 20-3 shows the comparator output block diagram. The TRIS bits will still function as the output enable/disable for the I/O pins while in this mode. Note 1: When reading the Port register, all pins configured as analog inputs will read as a `0'. Pins configured as digital inputs will convert an analog input according to the Schmitt Trigger input specification. Note 2: Analog levels on any pin that is defined as a digital input may cause the input buffer to consume more current than is specified. Figure 20-3: Comparator Output Block Diagram Port Pins MULTIPLEX + - To I/O pin Bus Data Q RD CMCON Set CMIF bit D EN Q From Other Comparator D EN CL RD CMCON RESET DS31020A-page 20-8 1997 Microchip Technology Inc. Section 20. Comparator 20.8 Comparator Interrupts The comparator interrupt flag is set whenever the comparators value changes relative to the last value loaded into CMxOUT bits. Software will need to maintain information about the status of the output bits, as read from CMCON<7:6>, to determine the actual change that has occurred. The CMIF bit, is the comparator interrupt flag. The CMIF bit must be cleared. Since it is also possible to set this bit, a simulated interrupt may be initiated. The CMIE bit and the PEIE bit (INTCON<6>) must be set to enable the interrupt. In addition, the GIE bit must also be set. If any of these bits are clear, the interrupt is not enabled, though the CMIF bit will still be set if an interrupt condition occurs. The user, in the interrupt service routine, can clear the interrupt in the following manner: a) b) Any read or write of the CMCON register. This will load the CMCON register with the new value with the CMxOUT bits. Clear the CMIF flag bit. An interrupt condition will continue to set the CMIF flag bit. Reading CMCON will end the interrupt condition, and allow the CMIF flag bit to be cleared. 20.9 Comparator Operation During SLEEP When a comparator is active and the device is placed in SLEEP mode, the comparator remains active and the interrupt is functional if enabled. This interrupt will wake up the device from SLEEP mode when enabled. While the comparator is powered-up, each comparator that is operational will consume additional current as shown in the comparator specifications. To minimize power consumption while in SLEEP mode, turn off the comparators, CM2:CM0 = 111, before entering sleep. If the device wakes-up from sleep, the contents of the CMCON register are not affected. 20.10 Effects of a RESET A device reset forces the CMCON register to its reset state. This forces the comparator module to be in the comparator reset mode, CM2:CM0 = 000. This ensures that all potential inputs are analog inputs. Device current is minimized when analog inputs are present at reset time. The comparators will be powered-down during the reset interval. 20 Comparator 1997 Microchip Technology Inc. DS31020A-page 20-9 PICmicro MID-RANGE MCU FAMILY 20.11 Analog Input Connection Considerations A simplified circuit for an analog input is shown in Figure 20-4. Since the analog pins are connected to a digital output, they have reverse biased diodes to VDD and VSS. The analog input therefore, must be between VSS and VDD. If the input voltage deviates from this range by more than 0.6V in either direction, one of the diodes is forward biased and a latch-up may occur. A maximum source impedance of 10 k is recommended for the analog sources. Figure 20-4: Analog Input Model VDD VT = 0.6V RS RC < 10k AIN CPIN 5 pF VAIN VT = 0.6V ILEAKAGE 500 nA VSS Legend CPIN VT ILEAKAGE RIC RS VA = Input Capacitance = Threshold Voltage = Leakage Current at the pin due to various junctions = Interconnect Resistance = Source Impedance = Analog Voltage Table 20-1: Registers Associated with Comparator Module Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on All Other Resets CMCON VRCON C2OUT VREN C1OUT VROE -- VRR -- -- CIS VR3 CM2 VR2 CM1 VR1 CM0 VR0 00-- 0000 000- 0000 00-- 0000 000- 0000 INTCON GIE PEIE T0IE INTE RBIE(2) T0IF INTF RBIF(2) 0000 000x 0000 000x 0 0 0 0 Name PIR CMIF (1) PIE CMIE (1) Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for Comparator Module. Note 1: The position of this bit is device dependent. 2: These bits can also be named GPIE and GPIF. DS31020A-page 20-10 1997 Microchip Technology Inc. Section 20. Comparator 20.12 Initialization The code in Example 20-1 depicts example steps required to configure the comparator module of the PIC16C62X devices. RA3 and RA4 are configured as digital output. RA0 and RA1 are configured as the V- inputs and RA2 as the V+ input to both comparators. Example 20-1: FLAG_REG ; CLRF CLRF ANDLW IORWF MOVLW MOVWF BSF MOVLW MOVWF BCF CALL MOVF BCF BSF BSF BCF BSF BSF EQU Initializing Comparator Module (PIC16C62X) 0X20 FLAG_REG PORTA 0xC0 FLAG_REG,F 0x03 CMCON STATUS,RP0 0x07 TRISA STATUS,RP0 DELAY 10 CMCON,F PIR1,CMIF STATUS,RP0 PIE1,CMIE STATUS,RP0 INTCON,PEIE INTCON,GIE ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; Init flag register Init PORTA Mask comparator bits Store bits in flag register Init comparator mode CM<2:0> = 011 Select Bank1 Initialize data direction Set RA<2:0> as inputs, RA<4:3> as outputs, TRISA<7:5> always read `0' Select Bank0 10s delay Read CMCON to end change condition Clear pending interrupts Select Bank1 Enable comparator interrupts Select Bank0 Enable peripheral interrupts Global interrupt enable 20 Comparator 1997 Microchip Technology Inc. DS31020A-page 20-11 PICmicro MID-RANGE MCU FAMILY 20.13 Design Tips Question 1: My program appears to lock up. Answer 1: You may be getting stuck in an infinite loop with the comparator interrupt service routine if you did not follow the proper sequence to clear the CMIF flag bit. First you must read the CMCON register, and then you can clear the CMIF flag bit. DS31020A-page 20-12 1997 Microchip Technology Inc. Section 20. Comparator 20.14 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the comparator module are: Title Resistance and Capacitance Meter using a PIC16C622 Application Note # AN611 20 Comparator 1997 Microchip Technology Inc. DS31020A-page 20-13 PICmicro MID-RANGE MCU FAMILY 20.15 Revision History Revision A This is the initial released revision of the Comparator module description. DS31020A-page 20-14 1997 Microchip Technology Inc. 8-bit A/D Convertor M 21 Section 21. 8-bit A/D Converter HIGHLIGHTS This section of the manual contains the following major topics: 21.1 Introduction ..................................................................................................................21-2 21.2 Control Registers .........................................................................................................21-3 21.3 Operation .....................................................................................................................21-5 21.4 A/D Acquisition Requirements .....................................................................................21-6 21.5 Selecting the A/D Conversion Clock ............................................................................21-8 21.6 Configuring Analog Port Pins.......................................................................................21-9 21.7 A/D Conversions ........................................................................................................21-10 21.8 A/D Operation During Sleep ......................................................................................21-12 21.9 A/D Accuracy/Error ....................................................................................................21-13 21.10 Effects of a RESET ....................................................................................................21-13 21.11 Use of the CCP Trigger ..............................................................................................21-14 21.12 Connection Considerations ........................................................................................21-14 21.13 Transfer Function .......................................................................................................21-14 21.14 Initialization ................................................................................................................21-15 21.15 Design Tips ................................................................................................................21-16 21.16 Related Application Notes..........................................................................................21-17 21.17 Revision History .........................................................................................................21-18 Note: 1997 Microchip Technology Inc. Please refer to Appendix C.3 or device Data Sheet to determine which devices use this module. DS31021A page 21-1 PICmicro MID-RANGE MCU FAMILY 21.1 Introduction The analog-to-digital (A/D) converter module has up to eight analog inputs. The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device's positive supply voltage (VDD) or the voltage level on the VREF pin. The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. The A/D module has three registers. These registers are: * A/D Result Register (ADRES) * A/D Control Register0 (ADCON0) * A/D Control Register1 (ADCON1) The ADCON0 register, shown in Figure 21-1, controls the operation of the A/D module. The ADCON1 register, shown in Figure 21-2, configures the functions of the port pins. The I/O pins can be configured as analog inputs (one I/O can also be a voltage reference) or as digital I/O. The block diagram of the A/D module is shown in Figure 21-1. Figure 21-1: 8-bit A/D Block Diagram CHS2:CHS0 111 AN7 110 AN6 101 AN5 100 AN4 VAIN 011 (Input voltage) AN3/VREF 010 AN2 8-bit A/D Converter 001 AN1 VDD (1) 000 AN0 000 or 010 or 100 VREF (Reference voltage) 001 or 011 or 101 PCFG2:PCFG0 Note: On some devices this is a separate pin called AVDD. This allows the A/D VDD to be connected to a precise voltage source. DS31021A-page 21-2 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.2 21 Control Registers Register 21-1: ADCON0 Register R/W-0 ADCS0 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 bit 7:6 ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from the internal A/D RC oscillator) bit 5:3 CHS2:CHS0: Analog Channel Select bits R/W-0 GO/DONE R/W-0 Resv R/W-0 ADON bit 0 000 = channel 0, (AN0) 001 = channel 1, (AN1) 010 = channel 2, (AN2) 011 = channel 3, (AN3) 100 = channel 4, (AN4) 101 = channel 5, (AN5) 110 = channel 6, (AN6) 111 = channel 7, (AN7) Note: bit 2 For devices that do not implement the full 8 A/D channels, the unimplemented selections are reserved. Do not select any unimplemented channels. GO/DONE: A/D Conversion Status bit When ADON = 1 1 = A/D conversion in progress (Setting this bit starts the A/D conversion. This bit is automatically cleared by hardware when the A/D conversion is complete) 0 = A/D conversion not in progress bit 1 Reserved: Always maintain this bit cleared. bit 0 ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. - n = Value at POR reset DS31021A-page 21-3 8-bit A/D Converter R/W-0 ADCS1 bit 7 PICmicro MID-RANGE MCU FAMILY Register 21-2: ADCON1 Register U-0 -- bit 7 U-0 -- U-0 -- U-0 -- U-0 -- bit 7:3 Unimplemented: Read as '0' bit 2:0 PCFG2:PCFG0: A/D Port Configuration Control bits R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit 0 PCFG2:PCFG0 AN7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 000 001 010 011 100 101 11x A A D D D D D A A D D D D D A A D A D D D A A A A D D D A VREF A VREF A VREF D A A A A D D D A A A A A A D A A A A A A D A = Analog input Note: D = Digital I/O When AN3 is selected as VREF, the A/D reference is the voltage on the AN3 pin. When AN3 is selected as an analog input (A), then the voltage reference for the A/D is the device VDD. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: On any device reset, the Port pins multiplexed with analog functions (ANx) are forced to be an analog input. DS31021A-page 21-4 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.3 21 Operation After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Subsection 21.4 "A/D Acquisition Requirements." After this acquisition time has elapsed the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. 2. 3. 4. 5. Configure the A/D module: * Configure analog pins / voltage reference / and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear the ADIF bit * Set the ADIE bit * Set the GIE bit Wait the required acquisition time. Start conversion: * Set the GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared OR 6. 7. * Waiting for the A/D interrupt Read A/D Result register (ADRES), clear the ADIF bit, if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts. Figure 21-2 shows the conversion sequence, and the terms that are used. Acquisition time is the time that the A/D module's holding capacitor is connected to the external voltage level. Then there is the conversion time of 10 TAD, which is started when the GO bit is set. The sum of these two times is the sampling time. There is a minimum acquisition time to ensure that the holding capacitor is charged to a level that will give the desired accuracy for the A/D conversion. Figure 21-2: A/D Conversion Sequence A/D Sample Time Acquisition Time Conversion Time A/D conversion complete, result is loaded in ADRES register. Holding capacitor begins acquiring voltage level on selected channel. ADIF bit is set. When A/D conversion is started (setting the GO bit). Holding capacitor is disconnected from the analog input before the conversion is started. When A/D holding capacitor start to charge. After A/D conversion, or new A/D channel is selected. 1997 Microchip Technology Inc. DS31021A-page 21-5 8-bit A/D Converter When the A/D conversion is complete, the result is loaded into the ADRES register, the GO/DONE bit (ADCON0<2>) is cleared, and A/D interrupt flag bit, ADIF, is set. PICmicro MID-RANGE MCU FAMILY 21.4 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 21-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD) (Figure 21-3). The maximum recommended impedance for analog sources is 10 k. After the analog input channel is selected (changed) the acquisition must be done before the conversion can be started. To calculate the minimum acquisition time, Equation 21-1 may be used. This equation assumes that 1/2 LSb error is used (512 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. Equation 21-1: TACQ = = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient TAMP + TC + TCOFF Equation 21-2: VHOLD = or = Tc Acquisition Time A/D Minimum Charging Time (VREF - (VREF/512)) * (1 - e(-Tc/CHOLD(RIC + RSS + RS))) -(51.2 pF)(1 k + RSS + RS) ln(1/511) Example 21-1 shows the calculation of the minimum required acquisition time TACQ. This calculation is based on the following system assumptions. Rs Conversion Error VDD Temperature VHOLD Example 21-1: DS31021A-page 21-6 = = = = 10 k 1/2 LSb 5V Rss = 7 k 50C (system max.) 0V @ time = 0 (see graph in Figure 21-3) Calculating the Minimum Required Acquisition Time TACQ = TAMP + TC + TCOFF TACQ = 5 s + Tc + [(Temp - 25C)(0.05 s/C)] TC = -CHOLD (RIC + RSS + RS) ln(1/512) -51.2 pF (1 k + 7 k + 10 k) ln(0.0020) -51.2 pF (18 k) ln(0.0020) -0.921 s (-6.2146) 5.724 s TACQ = 5 s + 5.724 s + [(50C - 25C)(0.05 s/C)] 10.724 s + 1.25 s 11.974 s 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21 Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out. Note 3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification. Note 4: After a conversion has completed, a 2.0 TAD delay must complete before acquisition can begin again. During this time the holding capacitor is not connected to the selected A/D input channel. Figure 21-3: Analog Input Model VDD Rs VT = 0.6V ANx CPIN 5 pF VAIN Sampling Switch VT = 0.6V RIC 1k SS RSS I leakage 500 nA CHOLD = 51.2 pF VSS Legend CPIN = input capacitance VT = threshold voltage I LEAKAGE = leakage current at the pin due to various junctions RIC SS CHOLD VAIN = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) = Analog input voltage 1997 Microchip Technology Inc. 6V 5V VDD 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch ( k ) DS31021A-page 21-7 8-bit A/D Converter Note 2: The charge holding capacitor (CHOLD) is not discharged after each conversion. PICmicro MID-RANGE MCU FAMILY 21.5 Selecting the A/D Conversion Clock The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5 TAD per 8-bit conversion. The source of the A/D conversion clock is software selected. The four possible options for TAD are: * * * * 2TOSC 8TOSC 32TOSC Internal RC oscillator For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 s for all devices, as shown in parameter 130 of the devices electrical specifications. Table 21-1 and Table 21-2 show the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. Table 21-1: TAD vs. Device Operating Frequencies (for Standard, C, Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 20 MHz 5 MHz 1.25 MHz 333.33 kHz 00 100 400 1.6 s 6 s 01 400 ns(2) 1.6 s 6.4 s 24 s(3) (3) 10 1.6 s 6.4 s 25.6 s 96 s(3) (1,4) (1,4) (1,4) 11 2 - 6 s 2 - 6 s 2 - 6 s 2 - 6 s(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. ns(2) ns(2) Table 21-2: TAD vs. Device Operating Frequencies (for Extended, LC, Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 4 MHz 2 MHz 1.25 MHz 333.33 kHz 00 500 ns(2) 1.0 s(2) 1.6 s(2) 6 s (2) 01 2.0 s 4.0 s 6.4 s 24 s(3) 10 8.0 s 16.0 s 25.6 s(3) 96 s(3) 11 3 - 9 s(1,4) 3 - 9 s(1,4) 3 - 9 s(1,4) 3 - 9 s(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 6 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. DS31021A-page 21-8 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.6 21 Configuring Analog Port Pins The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. Note 1: When reading the port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. Note 2: Analog levels on any pin that is defined as a digital input (including the AN7:AN0 pins), may cause the input buffer to consume current that is out of the devices specification. 1997 Microchip Technology Inc. DS31021A-page 21-9 8-bit A/D Converter ADCON1 and the corresponding TRIS registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. PICmicro MID-RANGE MCU FAMILY 21.7 A/D Conversions Example 21-2 show how to perform an A/D conversion. The I/O pins are configured as analog inputs. The analog reference (VREF) is the device VDD. The A/D interrupt is enabled, and the A/D conversion clock is FRC. The conversion is performed on the AN0 channel. Note: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D, due to the required acquition time requirement. Clearing the GO/DONE bit during a conversion will abort the current conversion. The ADRES register will NOT be updated with the partially completed A/D conversion sample. That is, the ADRES register will continue to contain the value of the last completed conversion (or the last value written to the ADRES register). After the A/D conversion is aborted, a 2TAD wait is required before the next acquisition is started. After this 2TAD wait, an acquisition is automatically started on the selected channel. Example 21-2: BSF CLRF BSF BCF MOVLW MOVWF BCF BSF BSF ; ; ; ; Doing an A/D Conversion STATUS, ADCON1 PIE1, STATUS, 0xC1 ADCON0 PIR1, INTCON, INTCON, RP0 ; ; ; ; ; ; ; ; ; ADIE RP0 ADIF PEIE GIE Select Bank1 Configure A/D inputs Enable A/D interrupts Select Bank0 RC Clock, A/D is on, Channel 0 is selected Clear A/D interrupt flag bit Enable peripheral interrupts Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : : ADCON0, GO ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE ; bit is cleared upon completion of the ; A/D Conversion. Figure 21-4: A/D Conversion TAD Cycles TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 b7 b6 b5 b4 b3 b2 b1 Holding capacitor is disconnected from analog input TAD9 TAD10 TAD11 b0 b0 Next Q4: ADRES is loaded GO bit is cleared ADIF bit is set Set GO bit Holding capacitor is connected to analog input DS31021A-page 21-10 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21 Figure 21-5: Flowchart of A/D Operation ADON = 0 8-bit A/D Converter Yes ADON = 0? No Acquire Selected Channel Yes GO = 0? No A/D Clock = RC? Yes Start of A/D Conversion Delayed 1 Instruction Cycle Finish Conversion GO = 0 ADIF = 1 No No Device in SLEEP? SLEEP Yes Instruction? Yes Abort Conversion GO = 0 ADIF = 0 Finish Conversion GO = 0 ADIF = 1 Wait 2TAD No No Finish Conversion GO = 0 ADIF = 1 Wake-up Yes From Sleep? SLEEP Power-down A/D Wait 2TAD Stay in Sleep Power-down A/D Wait 2TAD 1997 Microchip Technology Inc. DS31021A-page 21-11 PICmicro MID-RANGE MCU FAMILY 21.7.1 Faster Conversion - Lower Resolution Trade-off Not all applications require a result with 8-bits of resolution, but may instead require a faster conversion time. The A/D module allows users to make the trade-off of conversion speed to resolution. Regardless of the resolution required, the acquisition time is the same. To speed up the conversion, the clock source of the A/D module may be switched so that the TAD time violates the minimum specified time (see the applicable electrical specification). Once the TAD time violates the minimum specified time, all the following A/D result bits are not valid (see A/D Conversion Timing in the Electrical Specifications section). The clock sources may only be switched between the three oscillator versions (cannot be switched from/to RC). The equation to determine the time before the oscillator can be switched is as follows: Conversion time = Where: N = TAD + N * TAD + (10 - N)(2TOSC) number of bits of resolution required. Since the TAD is based from the device oscillator, the user must use some method (a timer, software loop, etc.) to determine when the A/D oscillator may be changed. Example 21-3 shows a comparison of time required for a conversion with 4-bits of resolution, versus the 8-bit resolution conversion. The example is for devices operating at 20 MHz (The A/D clock is programmed for 32TOSC), and assumes that immediately after 5TAD, the A/D clock is programmed for 2TOSC. The 2TOSC violates the minimum TAD time since the last 4-bits will not be converted to correct values. Example 21-3: 4-bit vs. 8-bit Conversion Times Freq. (MHz)(1) Resolution 4-bit 8-bit 20 1.6 s 1.6 s TAD TOSC 20 50 ns 50 ns TAD + N * TAD + (10 - N)(2TOSC) 20 8.6 s 17.6 s Note 1: A minimum TAD time of 1.6 s is required. 2: If the full 8-bit conversion is required, the A/D clock source should not be changed. 21.8 A/D Operation During Sleep The A/D module can operate during SLEEP mode. This requires that the A/D clock source be set to RC (ADCS1:ADCS0 = 11). When the RC clock source is selected, the A/D module waits one instruction cycle before starting the conversion. This allows the SLEEP instruction to be executed, which eliminates all internal digital switching noise from the conversion. When the conversion is completed the GO/DONE bit will be cleared, and the result loaded into the ADRES register. If the A/D interrupt is enabled, the device will wake-up from SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off (to conserve power), although the ADON bit will remain set. When the A/D clock source is another clock option (not RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off, though the ADON bit will remain set. Turning off the A/D places the A/D module in its lowest current consumption state. Note: DS31021A-page 21-12 For the A/D module to operate in SLEEP, the A/D clock source must be set to RC (ADCS1:ADCS0 = 11). To perform an A/D conversion in SLEEP, the GO/DONE bit must be set, followed by the SLEEP instruction. 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.9 21 A/D Accuracy/Error The absolute accuracy specified for the A/D converter includes the sum of all contributions for quantization error, integral error, differential error, full scale error, offset error, and monotonicity. It is defined as the maximum deviation from an actual transition versus an ideal transition for any code. The absolute error of the A/D converter is specified at < 1 LSb for VDD = VREF (over the device's specified operating range). However, the accuracy of the A/D converter will degrade as VDD diverges from VREF. For a given range of analog inputs, the output digital code will be the same. This is due to the quantization of the analog input to a digital code. Quantization error is typically 1/2 LSb and is inherent in the analog to digital conversion process. The only way to reduce quantization error is to increase the resolution of the A/D converter. Offset error measures the first actual transition of a code versus the first ideal transition of a code. Offset error shifts the entire transfer function. Offset error can be calibrated out of a system or introduced into a system through the interaction of the total leakage current and source impedance at the analog input. Gain error measures the maximum deviation of the last actual transition and the last ideal transition adjusted for offset error. This error appears as a change in slope of the transfer function. The difference in gain error to full scale error is that full scale does not take offset error into account. Gain error can be calibrated out in software. Linearity error refers to the uniformity of the code changes. Linearity errors cannot be calibrated out of the system. Integral non-linearity error measures the actual code transition versus the ideal code transition adjusted by the gain error for each code. Differential non-linearity measures the maximum actual code width versus the ideal code width. This measure is unadjusted. The maximum pin leakage current is specified in the Device Data Sheet electrical specification parameter D060. In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. TAD must not violate the minimum and should be minimized to reduce inaccuracies due to noise and sampling capacitor bleed off. In systems where the device will enter SLEEP mode after the start of the A/D conversion, the RC clock source selection is required. In this mode, the digital noise from the modules in SLEEP are stopped. This method gives high accuracy. 21.10 Effects of a RESET A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The value that is in the ADRES register is not modified for a Power-on Reset. The ADRES register will contain unknown data after a Power-on Reset. 1997 Microchip Technology Inc. DS31021A-page 21-13 8-bit A/D Converter In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. PICmicro MID-RANGE MCU FAMILY 21.11 Use of the CCP Trigger An A/D conversion may be started by the "special event trigger" of a CCP module. This requires that the CCPxM3:CCPxM0 bits (CCPxCON<3:0>) be programmed as 1011 and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the GO/DONE bit will be set, starting the A/D conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead (moving the ADRES to the desired location). The appropriate analog input channel must be selected and the minimum acquisition done before the "special event trigger" sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), then the "special event trigger" will be ignored by the A/D module, but will still reset the Timer1 counter. 21.12 Connection Considerations If the input voltage exceeds the rail values (VSS or VDD) by greater than 0.3V, then the accuracy of the conversion is out of specification. An external RC filter can sometimes be added for anti-aliasing of the input signal. The R component should be selected to ensure that the total source impedance is kept under the 10 k recommended specification. Any external components connected (via hi-impedance) to an analog input pin (capacitor, zener diode, etc.) should have very little leakage current at the pin. 21.13 Transfer Function The ideal transfer function of the A/D converter is as follows: the first transition occurs when the analog input voltage (VAIN) is 1 LSb (or Analog VREF / 256) (Figure 21-6). Digital code output Figure 21-6: A/D Transfer Function FFh FEh 04h 03h 02h 01h 256 LSb (full scale) 255 LSb 4 LSb 3 LSb 2 LSb 0.5 LSb 1 LSb 00h Analog input voltage DS31021A-page 21-14 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.14 21 Initialization Example 21-4 shows the initialization of the A/D module for the PIC16C74A BSF CLRF BSF BCF MOVLW MOVWF BCF BSF BSF ; ; ; ; A/D Initialization (for PIC16C74A) STATUS, RP0 ADCON1 PIE1, ADIE STATUS, RP0 0xC1 ADCON0 PIR1, ADIF INTCON, PEIE INTCON, GIE ; ; ; ; ; ; ; ; ; Select Bank1 Configure A/D inputs Enable A/D interrupts Select Bank0 RC Clock, A/D is on, Channel 0 is selected Clear A/D interrupt flag bit Enable peripheral interrupts Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : : 1997 Microchip Technology Inc. ADCON0, GO ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE ; bit is cleared upon completion of the ; A/D Conversion. DS31021A-page 21-15 8-bit A/D Converter Example 21-4: PICmicro MID-RANGE MCU FAMILY 21.15 Design Tips Question 1: I am using one of your PIC16C7X devices, and I find that the Analog to Digital Converter result is not always accurate. What can I do to improve accuracy? Answer 1: 1. 2. 3. Make sure you are meeting all of the timing specifications. If you are turning the A/D module off and on, there is a minimum delay you must wait before taking a sample, if you are changing input channels, there is a minimum delay you must wait for this as well, and finally there is Tad, which is the time selected for each bit conversion. This is selected in ADCON0 and should be between 2 and 6s. If TAD is too short, the result may not be fully converted before the conversion is terminated, and if TAD is made too long the voltage on the sampling capacitor can droop before the conversion is complete. These timing specifications are provided in the data book in a table or by way of a formula, and should be looked up for your specific part and circumstances. Often the source impedance of the analog signal is high (greater than 1k ohms) so the current drawn from the source to charge the sample capacitor can affect accuracy. If the input signal does not change too quickly, try putting a 0.1 F capacitor on the analog input. This capacitor will charge to the analog voltage being sampled, and supply the instantaneous current needed to charge the 51.2 pf internal holding capacitor. Finally, straight from the data book: "In systems where the device frequency is low, use of the A/D clock derived from the device oscillator is preferred...this reduces, to a large extent, the effects of digital switching noise." and "In systems where the device will enter SLEEP mode after start of A/D conversion, the RC clock source selection is required. This method gives the highest accuracy." Question 2: After starting an A/D conversion may I change the input channel (for my next conversion)? Answer 2: After the holding capacitor is disconnected from the input channel, one TAD after the GO bit is set, the input channel may be changed. Question 3: Do you know of a good reference on A/D's? Answer 3: A very good reference for understanding A/D conversions is the "Analog-Digital Conversion Handbook" third edition, published by Prentice Hall (ISBN 0-13-03-2848-0). DS31021A-page 21-16 1997 Microchip Technology Inc. Section 21. 8-bit A/D Converter 21.16 21 Related Application Notes Title Application Note # Using the Analog to Digital Converter AN546 Four Channel Digital Voltmeter with Display and Keyboard AN557 1997 Microchip Technology Inc. DS31021A-page 21-17 8-bit A/D Converter This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the 8-bit A/D are: PICmicro MID-RANGE MCU FAMILY 21.17 Revision History Revision A This is the initial released revision of the 8-bit A/D module description. DS31021A-page 21-18 1997 Microchip Technology Inc. M Section 22. Basic 8-bit A/D Converter HIGHLIGHTS This section of the manual contains the following major topics: 22 Note: 1997 Microchip Technology Inc. Please refer to Appendix C.2 or the device Data Sheet to determine which devices use this module. DS31022A page 22-1 Basic 8-bit A/D Converter 22.1 Introduction ..................................................................................................................22-2 22.2 Control Registers .........................................................................................................22-3 22.3 A/D Acquisition Requirements .....................................................................................22-6 22.4 Selecting the A/D Conversion Clock ............................................................................22-8 22.5 Configuring Analog Port Pins.....................................................................................22-10 22.6 A/D Conversions ........................................................................................................22-11 22.7 A/D Operation During Sleep ......................................................................................22-14 22.8 A/D Accuracy/Error ....................................................................................................22-15 22.9 Effects of a RESET ....................................................................................................22-16 22.10 Connection Considerations ........................................................................................22-16 22.11 Transfer Function .......................................................................................................22-16 22.12 Initialization ................................................................................................................22-17 22.13 Design Tips ................................................................................................................22-18 22.14 Related Application Notes..........................................................................................22-19 22.15 Revision History .........................................................................................................22-20 PICmicro MID-RANGE MCU FAMILY 22.1 Introduction This Analog-to-Digital (A/D) converter module has four analog inputs. The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device's positive supply voltage (VDD) or the voltage level on the AN3/VREF pin. The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. The A/D module has three registers. These registers are: * A/D Result Register (ADRES) * A/D Control Register0 (ADCON0) * A/D Control Register1 (ADCON1) The ADCON0 register, shown in Figure 22-1 controls the operation of the A/D module. The ADCON1 register, shown in Figure 22-2, configures the functions of the port pins. The port pins can be configured as analog inputs (or a voltage reference) or as digital I/O. Figure 22-1: Basic 8-bit A/D Block Diagram CHS1:CHS0 11 AN3/VREF VAIN 10 (Input voltage) AN2 01 Basic 8-bit Converter A/D AN1 00 AN0 VDD 00 or 10 or 11 VREF (Reference voltage) 01 PCFG1:PCFG0 DS31022A-page 22-2 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.2 Control Registers Register 22-1: ADCON0 Register R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADCS1 ADCS0 -- (1) CHS1 CHS0 GO/DONE ADIF / -- (2) ADON bit 7 bit 7:6 bit 0 ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from the internal A/D RC oscillator) 22 Basic 8-bit A/D Converter bit 5 Unimplemented: Read as '0'. bit 4:3 CHS1:CHS0: Analog Channel Select bits 00 = channel 0, (AN0) 01 = channel 1, (AN1) 10 = channel 2, (AN2) 11 = channel 3, (AN3) bit 2 GO/DONE: A/D Conversion Status bit If ADON = 1 1 = A/D conversion in progress (setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conversion is complete) bit 1 ADIF (2): A/D Conversion Complete Interrupt Flag bit 1 = conversion is complete (must be cleared in software) 0 = conversion is not complete bit 0 ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: For the PIC16C71, Bit5 of ADCON0 is a General Purpose R/W bit. For the PIC16C710/711/715, this bit is unimplemented, read as '0'. Note 2: For the PIC12CXXX devices, this bit is reserved. The ADIF bit is implemented in the PIR register. Use of this bit a a general purpose R/W bit is not recommended. Always maintain this bit cleared. 1997 Microchip Technology Inc. DS31022A-page 22-3 PICmicro MID-RANGE MCU FAMILY Register 22-2: ADCON1 Register U-0 -- U-0 U-0 -- U-0 -- U-0 U-0 / R/W-0 R/W-0 -- -- / PCFG2 (1) PCFG1 -- bit 7 bit 7:2 PCFG0 bit 0 Unimplemented: Read as '0' Note: bit 1:0 R/W-0 Some devices implement bit2 as the PCFG2 bit. PCFG1:PCFG0: A/D Port Configuration Control bits PCFG1:PCFG0 AN3 AN2 AN1 AN0 00 01 10 11 A A A D D A A A D A A A D VREF+ D D A = Analog input D = Digital I/O Note: bit 2:0 When AN3 is selected as VREF+, the A/D reference is the voltage on the AN3 pin. When AN3 is selected as an analog input (A), then the voltage reference for the A/D is the device VDD. PCFG2:PCFG0: A/D Port Configuration Control bits (1) PCFG2:PCFG0 AN3 AN2 AN1 AN0 000 001 010 011 100 101 110 111 A A D D D D D D A A A A D D D D A VREF+ A VREF+ A VREF+ D D A A A A A A A D A = Analog input D = Digital I/O Note: When AN1 is selected as VREF+, the A/D reference is the voltage on the AN1 pin. When AN1 is selected as an analog input (A), then the voltage reference for the A/D is the device VDD. Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: Some devices add an additional Port configuration bit (PCFG2). This allows the minimum number of analog channels to be one. This is of most benefit to the 8-pin devices with the A/D converter, since in an 8-pin device I/O is a premium resource. In the other devices this bit is unimplemented, and read as `0'. Note 2: On any device reset, the Port pins multiplexed with analog functions (ANx) are forced to be an analog input. DS31022A-page 22-4 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter The ADRES register contains the result of the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRES register, the GO/DONE bit (ADCON0<2>) is cleared, and A/D interrupt flag bit ADIF is set. The block diagram of the A/D module is shown in Figure 22-1. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine sample time, see Subsection 22.3 "A/D Acquisition Requirements" After this acquisition time has elapsed the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. 3. 4. 5. 22 Basic 8-bit A/D Converter 2. Configure the A/D module: * Configure analog pins / voltage reference / and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear the ADIF bit * Set the ADIE bit * Set the GIE bit Wait the required acquisition time. Start conversion: * Set the GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared OR 6. 7. * Waiting for the A/D interrupt Read A/D Result register (ADRES), clear the ADIF bit, if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts. Figure 22-2 shows the conversion sequence, and the terms that are used. Acquisition time is the time that the A/D module's holding capacitor is connected to the external voltage level. Then there is the conversion time of 10 TAD, which is started when the GO bit is set. The sum of these two times is the sampling time. There is a minimum acquisition time to ensure that the holding capacitor is charged to a level that will give the desired accuracy for the A/D conversion. Figure 22-2: A/D Conversion Sequence A/D Sample Time Acquisition Time A/D Conversion Time A/D conversion complete, result is loaded in ADRES register. Holding capacitor begins acquiring voltage level on selected channel ADIF bit is set When A/D conversion is started (setting the GO bit) When A/D holding capacitor start to charge. After A/D conversion, or new A/D channel is selected 1997 Microchip Technology Inc. DS31022A-page 22-5 PICmicro MID-RANGE MCU FAMILY 22.3 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 22-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), see Figure 22-3. The maximum recommended impedance for analog sources is 10 k. After the analog input channel is selected (changed) this acquisition must be done before the conversion can be started. To calculate the minimum acquisition time, Equation 22-1 may be used. This equation assumes that 1/2 LSb error is used (512 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. Equation 22-1:Acquisition Time TACQ = = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient TAMP + TC + TCOFF Equation 22-2:A/D Minimum Charging Time VHOLD = or = Tc (VREF - (VREF/512)) * (1 - e(-Tc/CHOLD(RIC + RSS + RS))) -(51.2 pF)(1 k + RSS + RS) ln(1/511) Example 22-1 shows the calculation of the minimum required acquisition time TACQ. This calculation is based on the following system assumptions. Rs Conversion Error VDD Temperature VHOLD Example 22-1: DS31022A-page 22-6 = = = = 10 k 1/2 LSb 5V Rss = 7 k 50C (system max.) 0V @ time = 0 (see graph in Figure 22-3) Calculating the Minimum Required Acquisition Time TACQ = TAMP + TC + TCOFF TACQ = 5 s + Tc + [(Temp - 25C)(0.05 s/C)] TC = -CHOLD (RIC + RSS + RS) ln(1/512) -51.2 pF (1 k + 7 k + 10 k) ln(0.0020) -51.2 pF (18 k) ln(0.0020) -0.921 s (-6.2146) 5.724 s TACQ = 5 s + 5.724 s + [(50C - 25C)(0.05 s/C)] 10.724 s + 1.25 s 11.974 s 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out. Note 2: The charge holding capacitor (CHOLD) is not discharged after each conversion. Note 3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification. Note 4: After a conversion has completed, a 2.0 TAD delay must complete before acquisition can begin again. During this time the holding capacitor is not connected to the selected A/D input channel. Figure 22-3: Analog Input Model 22 VDD VT = 0.6V RAx CPIN 5 pF VA VT = 0.6V RIC 1k SS RSS I leakage 500 nA CHOLD = 51.2 pF VSS Legend CPIN = input capacitance = threshold voltage VT I LEAKAGE = leakage current at the pin due to VARIOUS JUNCTIONS RIC SS CHOLD = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) 6V 5V VDD 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch ( k ) 1997 Microchip Technology Inc. DS31022A-page 22-7 Basic 8-bit A/D Converter Rs Sampling Switch PICmicro MID-RANGE MCU FAMILY 22.4 Selecting the A/D Conversion Clock The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5 TAD per 8-bit conversion. The source of the A/D conversion clock is software selected. The four possible options for TAD are: * * * * 2TOSC 8TOSC 32TOSC Internal RC oscillator For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of: 2.0 s for the PIC16C71, as shown in parameter 130 of devices electrical specifications. 1.6 s for all other devices, as shown in parameter 130 of devices electrical specifications. Table 22-1 through Table 22-4 show the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. Table 22-1: TAD vs. Device Operating Frequencies, All Devices (except PIC16C71) (C Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC(5) Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 20 MHz 5 MHz 1.25 MHz 333.33 kHz 00 100 400 1.6 s 6 s 01 400 ns(2) 1.6 s 6.4 s 24 s(3) (3) 10 1.6 s 6.4 s 25.6 s 96 s(3) (1,4) (1,4) (1,4) 11 2 - 6 s 2 - 6 s 2 - 6 s 2 - 6 s(1) The RC source has a typical TAD time of 4 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. ns(2) ns(2) Table 22-2: TAD vs. Device Operating Frequencies, All Devices (except PIC16LC71) (LC Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC(5) Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 4 MHz 2 MHz 1.25 MHz 333.33 kHz 00 500 ns(2) 1.0 s(2) 1.6 s(2) 6 s (2) 01 2.0 s 4.0 s 6.4 s 24 s(3) 10 8.0 s 16.0 s 25.6 s(3) 96 s(3) (1,4) (1,4) (1,4) 11 3 - 9 s 3 - 9 s 3 - 9 s 3 - 9 s(1) The RC source has a typical TAD time of 6 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. DS31022A-page 22-8 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter Table 22-3: TAD vs. Device Operating Frequencies, PIC16C71 ( C Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 20 MHz 16 MHz 4 MHz 1 MHz 333.33 kHz Table 22-4: TAD vs. Device Operating Frequencies, PIC16LC71 ( LC Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 4 MHz 2 MHz 1997 Microchip Technology Inc. s(2) 1.25 MHz 333.33 kHz 00 500 1.0 1.6 6 s 01 2.0 s(2) 4.0 s 6.4 s 24 s(3) 10 8.0 s 16.0 s 25.6 s(3) 96 s(3) (1,4) (1,4) (1,4) 11 3 - 9 s 3 - 9 s 3 - 9 s 3 - 9 s(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 6 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. ns(2) s(2) DS31022A-page 22-9 22 Basic 8-bit A/D Converter 00 100 ns(2) 125 ns(2) 500 ns(2) 2.0 s 6 s 01 400 ns(2) 500 ns(2) 2.0 s 8.0 s 24 s(3) 10 1.6 s(2) 2.0 s 8.0 s 32.0 s(3) 96 s(3) (1,4) (1,4) (1,4) (1) 11 2 - 6 s 2 - 6 s 2 - 6 s 2 - 6 s 2 - 6 s(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. PICmicro MID-RANGE MCU FAMILY 22.5 Configuring Analog Port Pins The ADCON1 and TRISA registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS1:CHS0 bits and the TRIS bits. Note 1: When reading the port register, all pins configured as analog input channel will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. Note 2: Analog levels on any pin that is defined as a digital input (including the AN3:AN0 pins), may cause the input buffer to consume current that is out of the devices specification. DS31022A-page 22-10 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.6 A/D Conversions Example 22-2 show how to perform an A/D conversion. The RA pins are configured as analog inputs. The analog reference (VREF) is the device VDD. The A/D interrupt is enabled, and the A/D conversion clock is FRC. The conversion is performed on the RA0 channel. Note: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D, due to the required acquisition time. Clearing the GO/DONE bit during a conversion will abort the current conversion. The ADRES register will NOT be updated with the partially completed A/D conversion sample. That is, the ADRES register will continue to contain the value of the last completed conversion (or the last value written to the ADRES register). After the A/D conversion is aborted, a 2TAD wait is required before the next acquisition is started. After this 2TAD wait, an acquisition is automatically started on the selected channel. BSF CLRF BCF MOVLW MOVWF BSF BSF ; ; ; ; Doing an A/D Conversion STATUS, ADCON1 STATUS, 0xC1 ADCON0 INTCON, INTCON, RP0 RP0 ADIE GIE ; ; ; ; ; ; ; Select Bank1 Configure A/D inputs Select Bank0 RC Clock, A/D is on, Channel 0 selected Enable A/D Interrupt Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : ADCON0, GO Figure 22-4: TAD1 ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE bit ; is cleared upon completion of the ; A/D Conversion. A/D Conversion TAD Cycles TAD2 b7 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 b6 b5 b4 b3 b2 b1 Holding capacitor is disconnected from analog input TAD9 TAD10 TAD11 b0 b0 Next Q4: ADRES is loaded GO bit is cleared ADIF bit is set Set GO bit Holding capacitor is connected to analog input 1997 Microchip Technology Inc. DS31022A-page 22-11 Basic 8-bit A/D Converter Example 22-2: 22 PICmicro MID-RANGE MCU FAMILY Figure 22-5: Flowchart of A/D Operation ADON = 0 Yes ADON = 0? No Acquire Selected Channel Yes GO = 0? No A/D Clock = RC? Yes Start of A/D Conversion Delayed 1 Instruction Cycle Finish Conversion GO = 0 ADIF = 1 No No Device in SLEEP? SLEEP Yes Instruction? Yes Abort Conversion GO = 0 ADIF = 0 Finish Conversion GO = 0 ADIF = 1 Wait 2TAD No No Finish Conversion GO = 0 ADIF = 1 Wake-up Yes From Sleep? SLEEP Power-down A/D Wait 2TAD Stay in Sleep Power-down A/D Wait 2TAD DS31022A-page 22-12 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.6.1 Faster Conversion - Lower Resolution Trade-off Not all applications require a result with 8-bits of resolution, but may instead require a faster conversion time. The A/D module allows users to make the trade-off of conversion speed to resolution. Regardless of the resolution required, the acquisition time is the same. To speed up the conversion, the clock source of the A/D module may be switched so that the TAD time violates the minimum specified time (see the applicable electrical specification). Once the TAD time violates the minimum specified time, all the following A/D result bits are not valid (see A/D Conversion Timing in the Electrical Specifications section.) The clock sources may only be switched between the three oscillator versions (cannot be switched from/to RC). The equation to determine the time before the oscillator can be switched is as follows: Conversion time = TAD + N * TAD + (10 - N)(2TOSC) Where: N = number of bits of resolution required. 22 The 2TOSC violates the minimum TAD time since the last 4-bits will not be converted to correct values. Example 22-3: 4-bit vs. 8-bit Conversion Times Freq. (MHz)(1) Resolution 4-bit 8-bit 20 1.6 s 1.6 s 16 2.0 s 2.0 s TOSC 20 50 ns 50 ns 16 62.5 ns 62.5 ns TAD + N * TAD + (10 - N)(2TOSC) 20 8.6 s 17.6 s 16 10.75 s 22 s Note 1: The PIC16C71 has a minimum TAD time of 2.0 s. All other devices have a minimum TAD time of 1.6 s. 2: If the full 8-bit conversion is required, the A/D clock source should not be changed. TAD 1997 Microchip Technology Inc. DS31022A-page 22-13 Basic 8-bit A/D Converter Since the TAD is based from the device oscillator, the user must use some method (a timer, software loop, etc.) to determine when the A/D oscillator may be changed. Example 22-3 shows a comparison of time required for a conversion with 4-bits of resolution, versus the 8-bit resolution conversion. The example is for devices operating at 20 MHz and 16 MHz (The A/D clock is programmed for 32TOSC), and assumes that immediately after 5TAD, the A/D clock is programmed for 2TOSC. PICmicro MID-RANGE MCU FAMILY 22.7 A/D Operation During Sleep The A/D module can operate during SLEEP mode. This requires that the A/D clock source be set to RC (ADCS1:ADCS0 = 11). When the RC clock source is selected, the A/D module waits one instruction cycle before starting the conversion. This allows the SLEEP instruction to be executed, which eliminates all internal digital switching noise from the conversion. When the conversion is completed the GO/DONE bit will be cleared, and the result loaded into the ADRES register. If the A/D interrupt is enabled, the device will wake-up from SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set. When the A/D clock source is another clock option (not RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off, though the ADON bit will remain set. Turning off the A/D places the A/D module in its lowest current consumption state. Note: DS31022A-page 22-14 For the A/D module to operate in SLEEP, the A/D clock source must be set to RC (ADCS1:ADCS0 = 11). To perform an A/D conversion in SLEEP, the GO/DONE bit must be set, followed by the SLEEP instruction. 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.8 A/D Accuracy/Error In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. The absolute accuracy specified for the A/D converter includes the sum of all contributions for quantization error, integral error, differential error, full scale error, offset error, and monotonicity. It is defined as the maximum deviation from an actual transition versus an ideal transition for any code. The absolute error of the A/D converter is specified at < 1 LSb for VDD = VREF (over the device's specified operating range). However, the accuracy of the A/D converter will degrade as VDD diverges from VREF. For a given range of analog inputs, the output digital code will be the same. This is due to the quantization of the analog input to a digital code. Quantization error is typically 1/2 LSb and is inherent in the analog to digital conversion process. The only way to reduce quantization error is to increase the resolution of the A/D converter. Gain error measures the maximum deviation of the last actual transition and the last ideal transition adjusted for offset error. This error appears as a change in slope of the transfer function. The difference in gain error to full scale error is that full scale does not take offset error into account. Gain error can be calibrated out in software. Linearity error refers to the uniformity of the code changes. Linearity errors cannot be calibrated out of the system. Integral non-linearity error measures the actual code transition versus the ideal code transition adjusted by the gain error for each code. Differential non-linearity measures the maximum actual code width versus the ideal code width. This measure is unadjusted. The maximum pin leakage current is specified in the Device Data Sheet electrical specification parameter D060. In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. TAD must not violate the minimum and should be minimized to reduce inaccuracies due to noise and sampling capacitor bleed off. In systems where the device will enter SLEEP mode after the start of the A/D conversion, the RC clock source selection is required. In this mode, the digital noise from the modules in SLEEP are stopped. This method gives high accuracy. 1997 Microchip Technology Inc. DS31022A-page 22-15 Basic 8-bit A/D Converter Offset error measures the first actual transition of a code versus the first ideal transition of a code. Offset error shifts the entire transfer function. Offset error can be calibrated out of a system or introduced into a system through the interaction of the total leakage current and source impedance at the analog input. 22 PICmicro MID-RANGE MCU FAMILY 22.9 Effects of a RESET A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The value that is in the ADRES register is not modified for a Power-on Reset. The ADRES register will contain unknown data after a Power-on Reset. 22.10 Connection Considerations If the input voltage exceeds the rail values (VSS or VDD) by greater than 0.2V, then the accuracy of the conversion is out of specification. Note: Care must be taken when using the RA0 pin in A/D conversions due to its proximity to the OSC1 pin. An external RC filter is sometimes added for anti-aliasing of the input signal. The R component should be selected to ensure that the total source impedance is kept under the 10 k recommended specification. Any external components connected (via hi-impedance) to an analog input pin (capacitor, zener diode, etc.) should have very little leakage current at the pin. 22.11 Transfer Function The ideal transfer function of the A/D converter is as follows: the first transition occurs when the analog input voltage (VAIN) is 1 LSb (or Analog VREF / 256) (Figure 22-6). A/D Transfer Function Digital code output Figure 22-6: FFh FEh 04h 03h 02h 01h 256 LSb (full scale) 255 LSb 4 LSb 3 LSb 2 LSb 0.5 LSb 1 LSb 00h Analog input voltage DS31022A-page 22-16 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.12 Initialization Example 22-4 shows the initialization of the A/D module in the PIC16C711. Example 22-4: BSF CLRF BCF MOVLW MOVWF BSF BSF STATUS, ADCON1 STATUS, 0xC1 ADCON0 INTCON, INTCON, RP0 RP0 ADIE GIE ; ; ; ; ; ; ; Select Bank1 Configure A/D inputs Select Bank0 RC Clock, A/D is on, Channel 0 selected Enable A/D Interrupt Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : 1997 Microchip Technology Inc. ADCON0, GO ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE bit ; is cleared upon completion of the ; A/D Conversion. DS31022A-page 22-17 22 Basic 8-bit A/D Converter ; ; ; ; A/D Initialization (for PIC16C711) PICmicro MID-RANGE MCU FAMILY 22.13 Design Tips Question 1: I am using one of your PIC16C7X devices, and I find that the Analog to Digital Converter result is not always accurate. What can I do to improve accuracy? Answer 1: 1. 2. 3. 4. Make sure you are meeting all of the timing specifications. If you are turning the ADC off and on, there is a minimum delay you must wait before taking a sample, if you are changing input channels, there is a minimum delay you must wait for this as well, and finally there is TAD, which is the time selected for each bit conversion. This is selected in ADCON0 and should be between 2 and 6 s. If TAD is too short, the result may not be fully converted before the conversion is terminated, and if Tad is made too long the voltage on the sampling capacitor can droop before the conversion is complete. These timing specifications are provided in the data book in a table or by way of a formula, and should be looked up for your specific part and circumstances. Often the source impedance of the analog signal is high (greater than 1k ohms) so the current drawn from the source to charge the sample capacitor can affect accuracy. If the input signal does not change too quickly, try putting a 0.1 F capacitor on the analog input. This capacitor will charge to the analog voltage being sampled, and supply the instantaneous current needed to charge the 51.2 pf internal holding capacitor. On the PIC16C71, one of the analog input pins is next to an oscillator pin. Naturally if these traces are next to each other some noise can couple from the oscillator to the analog circuit. This is especially true when the clock source is an external canned oscillator, since its output is a square wave with a high frequency component to its sharp edge, as opposed to a crystal circuit which provides a slower rise sine wave. Again, decoupling the analog pin can help, or if you can spare it, turn the pin into an output and drive it low. This will really help eliminate cross coupling into the analog circuit. Finally, straight from the data book: "In systems where the device frequency is low, use of the A/D clock derived from the device oscillator is preferred...this reduces, to a large extent, the effects of digital switching noise." and "In systems where the device will enter SLEEP mode after start of A/D conversion, the RC clock source selection is required. This method gives the highest accuracy." Question 2: After starting an A/D conversion may I change the input channel (for my next conversion)? Answer 2: After the holding capacitor is disconnected from the input channel, one TAD after the GO bit is set, the input channel may be changed. Question 3: Do you know of a good reference on A/D's? Answer 3: A very good reference for understanding A/D conversions is the "Analog-Digital Conversion Handbook" third edition, published by Prentice Hall (ISBN 0-13-03-2848-0). DS31022A-page 22-18 1997 Microchip Technology Inc. Section 22. Basic 8-bit A/D Converter 22.14 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Basic 8-bit A/D module are: Title Application Note # Using the Analog to Digital Converter AN546 Four Channel Digital Voltmeter with Display and Keyboard AN557 22 Basic 8-bit A/D Converter 1997 Microchip Technology Inc. DS31022A-page 22-19 PICmicro MID-RANGE MCU FAMILY 22.15 Revision History Revision A This is the initial released revision of the Basic 8-bit A/D Converter module description. DS31022A-page 22-20 1997 Microchip Technology Inc. M Section 23. 10-bit A/D Converter HIGHLIGHTS This section of the manual contains the following major topics: Note 1: At present NO released mid-range MCU devices are available with this module. Devices are planned, but there is no schedule for availability. Please refer to Microchip's Web site or BBS for release of Product Briefs which detail the features of devices. If your current design requires a 10-bit A/D, please look at the PIC17C756 which has a 12-channel 10-bit A/D. This A/D has characteristics which are identical to this module's description. 1997 Microchip Technology Inc. Preliminary DS31023A page 23-1 23 10-bit A/D Converter 23.1 Introduction ..................................................................................................................23-2 23.2 Control Register ...........................................................................................................23-3 23.3 Operation .....................................................................................................................23-5 23.4 A/D Acquisition Requirements .....................................................................................23-6 23.5 Selecting the A/D Conversion Clock ............................................................................23-8 23.6 Configuring Analog Port Pins.......................................................................................23-9 23.7 A/D Conversions ........................................................................................................23-10 23.8 Operation During Sleep .............................................................................................23-14 23.9 Effects of a Reset.......................................................................................................23-14 23.10 A/D Accuracy/Error ....................................................................................................23-15 23.11 Connection Considerations ........................................................................................23-16 23.12 Transfer Function .......................................................................................................23-16 23.13 Initialization ................................................................................................................23-17 23.14 Design Tips ................................................................................................................23-18 23.15 Related Application Notes..........................................................................................23-19 23.16 Revision History .........................................................................................................23-20 PICmicro MID-RANGE MCU FAMILY 23.1 Introduction The analog-to-digital (A/D) converter module can have up to eight analog inputs for a device. The analog input charges a sample and hold capacitor. The output of the sample and hold capacitor is the input into the converter. The converter then generates a digital result of this analog level via successive approximation. This A/D conversion, of the analog input signal, results in a corresponding 10-bit digital number. The analog reference voltages (positive and negative supply) are software selectable to either the device's supply voltages (AVDD, AVss) or the voltage level on the AN3/VREF+ and AN2/VREFpins. The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. The A/D module has four registers. These registers are: * * * * A/D Result High Register (ADRESH) A/D Result Low Register (ADRESL) A/D Control Register0 (ADCON0) A/D Control Register1 (ADCON1) The ADCON0 register, shown in Figure 23-1, controls the operation of the A/D module. The ADCON1 register, shown in Figure 23-2, configures the functions of the port pins. The port pins can be configured as analog inputs (AN3 and AN2 can also be the voltage references) or as digital I/O. Figure 23-1: 10-bit A/D Block Diagram CHS2:CHS0 111 AN7 110 AN6 101 AN5 100 VAIN 011 (Input voltage) AN4 AN3 010 AN2 10-bit Converter A/D 001 AN1 PCFG0 000 AVDD AN0 VREF+ Reference voltage VREF- AVSS DS31023A-page 23-2 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.2 Control Register Register 23-1: ADCON0 Register R/W-0 ADCS1 bit 7 bit 7:6 R/W-0 ADCS0 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 R/W-0 GO/DONE U-0 -- R/W-0 ADON bit 0 ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from the internal A/D RC oscillator) bit 5:3 CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (AN0) 001 = channel 1, (AN1) 010 = channel 2, (AN2) 011 = channel 3, (AN3) 100 = channel 4, (AN4) 101 = channel 5, (AN5) 110 = channel 6, (AN6) 111 = channel 7, (AN7) Note: bit 2 For devices that do not implement the full 8 A/D channels, the unimplemented selections are reserved. Do not select any unimplemented channel. 23 GO/DONE: A/D Conversion Status bit 1 = A/D conversion in progress (setting this bit starts the A/D conversion which is automatically cleared by hardware when the A/D conversion is complete) 0 = A/D conversion not in progress bit 1 Unimplemented: Read as '0' bit 0 ADON: A/D On bit 1 = A/D converter module is powered up 0 = A/D converter module is shut off and consumes no operating current Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. Preliminary - n = Value at POR reset DS31023A-page 23-3 10-bit A/D Converter When ADON = 1 PICmicro MID-RANGE MCU FAMILY Register 23-2: ADCON1 Register U-0 -- bit 7 U-0 -- R/W-0 ADFM U-0 -- R/W-0 PCFG3 bit 7:6 Unimplemented: Read as '0' bit 5 ADFM: A/D Result format select (also see Figure 23-6). R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit 0 1 = Right justified. 6 Most Significant bits of ADRESH are read as '0'. 0 = Left justified. 6 Least Significant bits of ADRESL are read as '0'. bit 4 Unimplemented: Read as '0' bit 3:0 PCFG3:PCFG0: A/D Port Configuration Control bits PCFG AN7 AN6 AN5 AN4 0000 0001 0010 0011 0100 0101 011x 1000 1001 1010 1011 1100 1101 1110 1111 A A D D D D D A D D D D D D D A A D D D D D A D D D D D D D A A D D D D D A A A A D D D D A A A A D D D A A A A A D D D AN3 AN2 A VREF+ A VREF+ A VREF+ D VREF+ A VREF+ VREF+ VREF+ VREF+ D VREF+ A A A A D D D VREFA A VREFVREFVREFD VREF- AN1 AN0 VREF+ VREF- C/R AVSS AVSS AVSS AVSS AVSS AVSS -- AN2 AVSS AVSS AN2 AN2 AN2 AVSS AN2 8/0 7/1 5/0 4/1 3/0 2/1 0/0 6/2 6/0 5/1 4/2 3/2 2/2 1/0 1/2 A A A A A A D A A A A A A D D A A A A A A D A A A A A A A A AVDD AN3 AVDD AN3 AVDD AN3 -- AN3 AVDD AN3 AN3 AN3 AN3 AVDD AN3 A = Analog input D = Digital I/O C/R = # of analog input channels / # of A/D voltage references Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: On any device reset, the port pins that are multiplexed with analog functions (ANx) are forced to be an analog input. DS31023A-page 23-4 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.3 Operation The ADRESH:ADRESL registers contains the 10-bit result of the A/D conversion. When the A/D conversion is complete, the result is loaded into this A/D result register pair, the GO/DONE bit (ADCON0<2>) is cleared, and A/D interrupt flag bit, ADIF, is set. The block diagrams of the A/D module are shown in Figure 23-1. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as inputs. To determine sample time, see Subsection 23.4 "A/D Acquisition Requirements." After this acquisition time has elapsed the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. 2. 3. 4. 5. Configure the A/D module: * Configure analog pins / voltage reference/ and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear the ADIF bit * Set the ADIE bit * Set the GIE bit Wait the required acquisition time. Start conversion: * Set the GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared or ADIF bit to be set 23 6. 7. * Waiting for the A/D interrupt Read A/D Result register pair (ADRESH:ADRESL), clear the ADIF bit, if required. For next conversion, go to step 1 or step 2 as required. Figure 23-2 shows the conversion sequence, and the terms that are used. Acquisition time is the time that the A/D module's holding capacitor is connected to the external voltage level. Then there is the conversion time of 12 TAD, which is started when the GO bit is set. The sum of these two times is the sampling time. There is a minimum acquisition time to ensure that the holding capacitor is charged to a level that will give the desired accuracy for the A/D conversion. Figure 23-2: A/D Conversion Sequence A/D Sample Time Acquisition Time A/D Conversion Time A/D conversion complete, result is loaded in ADRES register. Holding capacitor begins acquiring voltage level on selected channel ADIF bit is set When A/D conversion is started (setting the GO bit) When A/D holding capacitor starts to charge. After A/D conversion, or when new A/D channel is selected 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-5 10-bit A/D Converter OR PICmicro MID-RANGE MCU FAMILY 23.4 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 23-3. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), Figure 23-3. The maximum recommended impedance for analog sources is 10 k. As the impedance is decreased, the acquisition time may be decreased. After the analog input channel is selected (changed) this acquisition must be done before the conversion can be started. To calculate the minimum acquisition time, Equation 23-1 may be used. This equation assumes that 1/2 LSb error is used (1024 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. Equation 23-1: TACQ = = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient TAMP + TC + TCOFF Equation 23-2: VHOLD or Tc Acquisition Time A/D Minimum Charging Time = (VREF - (VREF/2048)) * (1 - e(-Tc/CHOLD(RIC + RSS + RS))) = -(120 pF)(1 k + RSS + RS) ln(1/2047) Example 23-1 shows the calculation of the minimum required acquisition time TACQ. This calculation is based on the following application system assumptions. CHOLD Rs Conversion Error VDD Temperature VHOLD Example 23-1: TACQ = = = = = = 120 pF 10 k 1/2 LSb 5V Rss = 7 k 50C (system max.) 0V @ time = 0 (see graph in Figure 23-3) Calculating the Minimum Required Acquisition Time (Case 1) TAMP + TC + TCOFF Temperature coefficient is only required for temperatures > 25C. DS31023A-page 23-6 TACQ = 2 s + Tc + [(Temp - 25C)(0.05 s/C)] TC = -CHOLD (RIC + RSS + RS) ln(1/2047) -120 pF (1 k + 7 k + 10 k) ln(0.0004885) -120 pF (18 k) ln(0.0004885) -2.16 s (-7.6241) 16.47 s TACQ = 2 s + 16.47 s + [(50C - 25C)(0.05 s/C)] 18.47 s + 1.25 s 19.72 s Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter Now to get an idea what happens to the acquisition time when the source impedance is a minimal value (RS = 50 ). Example 23-2 shows the same conditions as in Example 23-1 with only the source impedance made a minimal value (RS = 50 ). Example 23-2: TACQ = Calculating the Minimum Required Acquisition Time (Case 2) TAMP + TC + TCOFF Temperature coefficient is only required for temperatures > 25C. TACQ = 2 s + Tc + [(Temp - 25C)(0.05 s/C)] TC = -CHOLD (RIC + RSS + RS) ln(1/2047) -120 pF (1 k + 7 k + 50 ) ln(0.0004885) -120 pF (8050 ) ln(0.0004885) -0.966 s (-7.6241) 7.36 s TACQ = 2 s + 16.47 s + [(50C - 25C)(0.05 s/C)] 9.36 s + 1.25 s 10.61 s Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out. Note 2: The charge holding capacitor (CHOLD) is not discharged after each conversion. Note 3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification. Figure 23-3: Analog Input Model VDD Rs VT = 0.6V ANx CPIN 5 pF VAIN Sampling Switch VT = 0.6V RIC 1k SS RSS I leakage 100 nA CHOLD = 120 pF VSS Legend CPIN = input capacitance VT = threshold voltage I LEAKAGE = leakage current at the pin due to various junctions RIC SS CHOLD = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) 1997 Microchip Technology Inc. Preliminary 6V 5V VDD 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch ( k ) DS31023A-page 23-7 10-bit A/D Converter Note 4: After a conversion has completed, a 2.0TAD delay must complete before acquisition can begin again. During this time the holding capacitor is not connected to the selected A/D input channel. 23 PICmicro MID-RANGE MCU FAMILY 23.5 Selecting the A/D Conversion Clock The A/D conversion time per bit is defined as TAD. The A/D conversion requires 11.5TAD per 10-bit conversion. The source of the A/D conversion clock is software selected. The four possible options for TAD are: * * * * 2TOSC 8TOSC 32TOSC Internal RC oscillator For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 s as shown in parameter 130 of the "Electrical Specifications" section. Table 23-1 show the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. These times are for standard voltage range devices. Table 23-1: TAD vs. Device Operating Frequencies (for Standard, C, Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 20 MHz 5 MHz 1.25 MHz 333.33 kHz 00 100 400 1.6 s 6 s 01 400 ns(2) 1.6 s 6.4 s 24 s(3) (3) 10 1.6 s 6.4 s 25.6 s 96 s(3) (1,4) (1,4) (1,4) 11 2 - 6 s 2 - 6 s 2 - 6 s 2 - 6 s(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. ns(2) ns(2) Table 23-2: TAD vs. Device Operating Frequencies (for Extended, LC, Devices) AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 Device Frequency 4 MHz 2 MHz DS31023A-page 23-8 s(2) 1.25 MHz 333.33 kHz 00 500 1.0 1.6 6 s 01 2.0 s(2) 4.0 s 6.4 s 24 s(3) 10 8.0 s 16.0 s 25.6 s(3) 96 s(3) (1,4) (1,4) (1,4) 11 3 - 9 s 3 - 9 s 3 - 9 s 3 - 9 s(1,4) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 6 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. For device frequencies above 1 MHz, the device must be in SLEEP for the entire conversion, or the A/D accuracy may be out of specification. ns(2) Preliminary s(2) 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.6 Configuring Analog Port Pins The ADCON1 and TRIS registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. Note 1: When reading the port register, any pin configured as an analog input channel will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. Note 2: Analog levels on any pin that is defined as a digital input (including the AN7:AN0 pins), may cause the input buffer to consume current that is out of the devices specification. 23 10-bit A/D Converter 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-9 PICmicro MID-RANGE MCU FAMILY 23.7 A/D Conversions Example 23-3 shows how to perform an A/D conversion for the PIC17C756. The PORTF and lower four PORTG pins are configured as analog inputs. The analog references (VREF+ and VREF-) are the device AVDD and AVSS. The A/D interrupt is enabled, and the A/D conversion clock is FRC. The conversion is performed on the AN0 pin (channel 0). Note: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D, due to the required acquisition time requirement. Clearing the GO/DONE bit during a conversion will abort the current conversion. The A/D result register pair will NOT be updated with the partially completed A/D conversion sample. That is, the ADRESH:ADRESL registers will continue to contain the value of the last completed conversion (or the last value written to the ADRESH:ADRESL registers). After the A/D conversion is aborted, a 2TAD wait is required before the next acquisition is started. After this 2TAD wait, acquisition on the selected channel is automatically started. Example 23-3: ; ; ; ; A/D Conversion BSF CLRF STATUS, RP0 ADCON1 BSF BCF MOVLW MOVWF BCF BSF BSF PIE1, ADIE STATUS, RP0 0xC1 ADCON0 PIR1, ADIF INTCON, PEIE INTCON, GIE ; ; ; ; ; ; ; ; ; ; Select Bank1 Configure A/D inputs, result is left justified Enable A/D interrupts Select Bank0 RC Clock, A/D is on, Channel 0 is selected Clear A/D interrupt flag bit Enable peripheral interrupts Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : : ADCON0, GO ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE ; bit is cleared upon completion of the ; A/D Conversion. Figure 23-4: A/D Conversion TAD Cycles Tcy - TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 TAD9 TAD10 TAD11 b0 b3 b1 b2 b0 b4 b5 b7 b6 b8 b9 Conversion Starts Holding capacitor is disconnected from analog input (typically 100 ns) Set GO bit Next Q4: ADRES is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. DS31023A-page 23-10 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter Figure 23-5: Flowchart of A/D Operation ADON = 0 Yes ADON = 0? No Acquire Selected Channel Yes GO = 0? No A/D Clock = RC? Yes Start of A/D Conversion Delayed 1 Instruction Cycle Finish Conversion GO = 0, ADIF = 1 No No Device in SLEEP? Yes SLEEP Instruction? Yes Abort Conversion GO = 0, ADIF = 0 Finish Conversion GO = 0, ADIF = 1 Wait 2TAD No No SLEEP Power-down A/D Wait 2TAD 23 Stay in Sleep Power-down A/D 10-bit A/D Converter Finish Conversion GO = 0, ADIF = 1 Wake-up Yes From Sleep? Wait 2TAD 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-11 PICmicro MID-RANGE MCU FAMILY 23.7.1 Faster Conversion - Lower Resolution Trade-off Not all applications require a result with 10-bits of resolution, but may instead require a faster conversion time. The A/D module allows users to make the trade-off of conversion speed to resolution. Regardless of the resolution required, the acquisition time is the same. To speed up the conversion, the clock source of the A/D module may be switched so that the TAD time violates the minimum specified time (see the applicable electrical specification). Once the TAD time violates the minimum specified time, all the following A/D result bits are not valid (see A/D Conversion Timing in the Electrical Specifications section). The clock sources may only be switched between the three oscillator versions (cannot be switched from/to RC). The equation to determine the time before the oscillator can be switched is as follows: Conversion time Where: N = TAD + N * TAD + (11 - N)(2TOSC) = number of bits of resolution required. Since the TAD is based from the device oscillator, the user must use some method (a timer, software loop, etc.) to determine when the A/D oscillator may be changed. Example 23-4 shows a comparison of time required for a conversion with 4-bits of resolution, versus the 10-bit resolution conversion. The example is for devices operating at 20 MHz (The A/D clock is programmed for 32TOSC), and assumes that immediately after 6TAD, the A/D clock is programmed for 2TOSC. The 2TOSC violates the minimum TAD time since the last 4 bits will not be converted to correct values. Example 23-4: 4-bit vs. 8-bit Conversion Times Freq. (MHz)(1) Resolution 4-bit 10-bit 20 1.6 s 1.6 s TAD TOSC 20 50 ns 50 ns 2TAD + N * TAD + (11 - N)(2TOSC) 20 8.7 s 17.6 s Note 1: A minimum TAD time of 1.6 s is required. 2: If the full 8-bit conversion is required, the A/D clock source should not be changed. DS31023A-page 23-12 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.7.2 A/D Result Registers The ADRESH:ADRESL register pair is the location where the 10-bit A/D result is loaded at the completion of the A/D conversion. This register pair is 16-bits wide. The A/D module gives the flexibility to left or right justify the 10-bit result in the 16-bit result register. The A/D Format Select bit (ADFM) controls this justification. Figure 23-6 shows the operation of the A/D result justification. The extra bits are loaded with `0's'. When an A/D result will not overwrite these locations (A/D disable), these registers may be used as two general purpose 8-bit registers. Figure 23-6: A/D Result Justification 10-Bit Result ADFM = 0 ADFM = 1 0 2107 7 0000 00 ADRESH RESULT ADRESL 10-bits 7 0765 RESULT ADRESH 0 0000 00 ADRESL 10-bits 23 Left Justified Right Justified 10-bit A/D Converter 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-13 PICmicro MID-RANGE MCU FAMILY 23.8 Operation During Sleep The A/D module can operate during SLEEP mode. This requires that the A/D clock source be set to RC (ADCS1:ADCS0 = 11). When the RC clock source is selected, the A/D module waits one instruction cycle before starting the conversion. This allows the SLEEP instruction to be executed, which eliminates all internal digital switching noise from the conversion. When the conversion is completed the GO/DONE bit will be cleared, and the result is loaded into the ADRES register. If the A/D interrupt is enabled, the device will wake-up from SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set. When the A/D clock source is another clock option (not RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off (to conserve power), though the ADON bit will remain set. Turning off the A/D places the A/D module in its lowest current consumption state. Note: 23.9 For the A/D module to operate in SLEEP, the A/D clock source must be set to RC (ADCS1:ADCS0 = 11). To allow the conversion to occur during SLEEP, ensure the SLEEP instruction immediately follows the instruction that sets the GO/DONE bit. Effects of a Reset A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The value that is in the ADRESH:ADRESL registers is not modified for a Power-on Reset. The ADRESH:ADRESL registers will contain unknown data after a Power-on Reset. DS31023A-page 23-14 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.10 A/D Accuracy/Error In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. The absolute accuracy specified for the A/D converter includes the sum of all contributions for quantization error, integral error, differential error, full scale error, offset error, and monotonicity. It is defined as the maximum deviation from an actual transition versus an ideal transition for any code. The absolute error of the A/D converter is specified at < 1 LSb for VDD = VREF (over the device's specified operating range). However, the accuracy of the A/D converter will degrade as VDD diverges from VREF. For a given range of analog inputs, the output digital code will be the same. This is due to the quantization of the analog input to a digital code. Quantization error is typically 1/2 LSb and is inherent in the analog to digital conversion process. The only way to reduce quantization error is to increase the resolution of the A/D converter. Offset error measures the first actual transition of a code versus the first ideal transition of a code. Offset error shifts the entire transfer function. Offset error can be calibrated out of a system or introduced into a system through the interaction of the total leakage current and source impedance at the analog input. Gain error measures the maximum deviation of the last actual transition and the last ideal transition adjusted for offset error. This error appears as a change in slope of the transfer function. The difference in gain error to full scale error is that full scale does not take offset error into account. Gain error can be calibrated out in software. Linearity error refers to the uniformity of the code changes. Linearity errors cannot be calibrated out of the system. Integral non-linearity error measures the actual code transition versus the ideal code transition adjusted by the gain error for each code. The maximum pin leakage current is specified in the Device Data Sheet electrical specification parameter D060. In systems where the device frequency is low, use of the A/D RC clock is preferred. At moderate to high frequencies, TAD should be derived from the device oscillator. TAD must not violate the minimum and should be minimized to reduce inaccuracies due to noise and sampling capacitor bleed off. In systems where the device will enter SLEEP mode after the start of the A/D conversion, the RC clock source selection is required. In this mode, the digital noise from the modules in SLEEP are stopped. This method gives high accuracy. 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-15 10-bit A/D Converter Differential non-linearity measures the maximum actual code width versus the ideal code width. This measure is unadjusted. 23 PICmicro MID-RANGE MCU FAMILY 23.11 Connection Considerations If the input voltage exceeds the rail values (VSS or VDD) by greater than 0.3V, then the accuracy of the conversion is out of specification. An external RC filter is sometimes added for anti-aliasing of the input signal. The R component should be selected to ensure that the total source impedance is kept under the 10 k recommended specification. Any external components connected (via hi-impedance) to an analog input pin (capacitor, zener diode, etc.) should have very little leakage current at the pin. 23.12 Transfer Function The ideal transfer function of the A/D converter is as follows: the first transition occurs when the analog input voltage (VAIN) is 1 LSb (or Analog VREF / 1024) (Figure 23-7). Figure 23-7: A/D Transfer Function 3FFh Digital code output 3FEh 003h 002h 001h 1023.5 LSb 1023 LSb 1022 LSb 1022.5 LSb 3 LSb 2.5 LSb 2 LSb 1.5 LSb 1 LSb 0.5 LSb 000h Analog input voltage DS31023A-page 23-16 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.13 Initialization Example 23-5 shows an initialization of the A/D module. Example 23-5: BSF CLRF BSF BCF MOVLW MOVWF BCF BSF BSF ; ; ; ; A/D Initialization STATUS, RP0 ADCON1 PIE1, ADIE STATUS, RP0 0xC1 ADCON0 PIR1, ADIF INTCON, PEIE INTCON, GIE ; ; ; ; ; ; ; ; ; Select Bank1 Configure A/D inputs Enable A/D interrupts Select Bank0 RC Clock, A/D is on, Channel 0 is selected Clear A/D interrupt flag bit Enable peripheral interrupts Enable all interrupts Ensure that the required sampling time for the selected input channel has elapsed. Then the conversion may be started. BSF : : : ADCON0, GO ; Start A/D Conversion ; The ADIF bit will be set and the GO/DONE ; bit is cleared upon completion of the ; A/D Conversion. 23 10-bit A/D Converter 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-17 PICmicro MID-RANGE MCU FAMILY 23.14 Design Tips Question 1: I find that the Analog to Digital Converter result is not always accurate. What can I do to improve accuracy? Answer 1: 1. 2. 3. Make sure you are meeting all of the timing specifications. If you are turning the module off and on, there is a minimum delay you must wait before taking a sample. If you are changing input channels, there is a minimum delay you must wait for this as well, and finally there is TAD, which is the time selected for each bit conversion. This is selected in ADCON0 and should be between 1.6 and 6 s. If TAD is too short, the result may not be fully converted before the conversion is terminated, and if TAD is made too long the voltage on the sampling capacitor can droop before the conversion is complete. These timing specifications are provided in the "Electrical Specifications" section. See the device data sheet for device specific information. Often the source impedance of the analog signal is high (greater than 1k ohms) so the current drawn from the source to charge the sample capacitor can affect accuracy. If the input signal does not change too quickly, try putting a 0.1 F capacitor on the analog input. This capacitor will charge to the analog voltage being sampled and supply the instantaneous current needed to charge the 120 pF internal holding capacitor. Finally, straight from the data book: "In systems where the device frequency is low, use of the A/D clock derived from the device oscillator is preferred...this reduces, to a large extent, the effects of digital switching noise." and "In systems where the device will enter SLEEP mode after start of A/D conversion, the RC clock source selection is required.This method gives the highest accuracy." Question 2: After starting an A/D conversion may I change the input channel (for my next conversion)? Answer 2: After the holding capacitor is disconnected from the input channel, typically 100 ns after the GO bit is set, the input channel may be changed. Question 3: Do you know of a good reference on A/D's? Answer 3: A very good reference for understanding A/D conversions is the "Analog-Digital Conversion Handbook" third edition, published by Prentice Hall (ISBN 0-13-03-2848-0). DS31023A-page 23-18 Preliminary 1997 Microchip Technology Inc. Section 23. 10-bit A/D Converter 23.15 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the 10-bit A/D module are: Title Application Note # Using the Analog to Digital Converter AN546 Four Channel Digital Voltmeter with Display and Keyboard AN557 23 10-bit A/D Converter 1997 Microchip Technology Inc. Preliminary DS31023A-page 23-19 PICmicro MID-RANGE MCU FAMILY 23.16 Revision History Revision A This is the initial released revision of the 10-bit A/D module description. DS31023A-page 23-20 1997 Microchip Technology Inc. M Section 24. Slope A/D HIGHLIGHTS This section of the manual contains the following major topics: 24.1 24.2 24.3 24.4 24.5 24.6 24.7 24.8 Introduction ..................................................................................................................24-2 Control Registers .........................................................................................................24-3 Conversion Process .....................................................................................................24-6 Other Analog Modules ...............................................................................................24-12 Calibration Parameters ..............................................................................................24-13 Design Tips ................................................................................................................24-14 Related Application Notes..........................................................................................24-15 Revision History .........................................................................................................24-16 24 Slope A/D 1997 Microchip Technology Inc. DS31024A page 24-1 PICmicro MID-RANGE MCU FAMILY 24.1 Introduction The components required to create a Slope A/D converter include: * * * * Precision comparator 4-bit programmable current source 16-channel analog MUX 16-bit timer with capture register This section will discuss using these components for a Slope A/D. Each analog input channel is multiplexed to a single analog input source to be converted by means of a slope conversion method (using a single precision comparator). The programmable current source feeds an external capacitor to generate the ramp voltage used in the conversion. Figure 24-1: Slope A/D Block Diagram OSC1 0 1 ADOFF Internal Oscillator FOSC (Configuration Bit) AN0 Clock Stop Logic ADRST AMUXOE (ADCON0<2>) AN15 AN14 AN7 AN6 AN5 AN4 AN13 AN12 AN11 SREFLO SREFHI Bandgap Ref. AN3 AN2 AN1 AN0 15 14 13 12 11 10 9 Analog 8 MUX 7 ~ 1 k 6 5 4 3 2 1 0 ADOFF Note 2 ADTMRH ADTMRL Timer Overflow Slope A/D Capture ADCAPH Slope A/D Capture Interrupt (ADCIF) ADCAPL Internal Data Bus 4 ADCON0<7:4> ~2.5uA~5uA~10uA~20uA ADOFF (SLPCON<0>) CDAC ADCON1<7:4> ~100 Note 3 C ADRST (ADCON0<1>) 4-Bit Current DAC (Note 1) DS31024A-page 24-2 Note 1: All current sources are disabled if ADRST = `1' 2: Approximately 3.5 microsecond time constant 3: Dependent on A/D resolution and input voltage range (see Table 24-2) 1997 Microchip Technology Inc. Section 24. Slope A/D 24.2 Control Registers Two A/D control registers are provided to control the conversion process. They are ADCON0 and ADCON1. Both registers are readable and writable. Register 24-1: ADCON0 Register R/W-0 ADCS3 bit 7 bit 7-4: R/W-0 ADCS2 R/W-0 ADCS1 R/W-0 ADCS0 U-0 -- R/W-0 AMUXOE R/W-1 ADRST R/W-0 ADZERO bit 0 ADCS3:ADCS0: Analog Channel Select bits 0000 = AN0 input 0001 = AN1 input 0010 = AN2 input 0011 = AN3 input 0100 = Bandgap reference voltage input 0101 = Slope reference SREFHI input 0110 = Slope reference SREFLO input 0111 = AN11 input 1000 = AN12 input 1001 = AN13 input 1010 = AN4 input 1011 = AN5 input 1100 = AN6 input 1101 = AN7 input 1110 = AN14 input 1111 = AN15 input Note: For devices that do not use the full 16 A/D input channels, the unimplemented selections are reserved. Do not select any unimplemented channels. bit 3: Unimplemented: Read as '0' bit 2: AMUXOE: Analog MUX Output Enable 1 = Connect AMUX Output to AN0 pin (overrides TRIS setting) 0 = AN0 pin normal bit 1: ADRST: A/D Reset Control Bit 24 1 = Stop the A/D Timer, discharge CDAC capacitor 0 = Normal operation (A/D running) bit 0: ADZERO: A/D Zero Select Control Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' 1997 Microchip Technology Inc. Slope A/D 1 = Enable zeroing operation on AN1 and AN5 0 = Normal operation, sample AN1 and AN5 pins - n = Value at POR reset DS31024A-page 24-3 PICmicro MID-RANGE MCU FAMILY Register 24-2: ADCON1 Register R/W-0 ADDAC3 bit 7 bit 7-4: R/W-0 ADDAC2 R/W-0 ADDAC1 R/W-0 ADDAC0 R/W-0 PCFG3 R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit 0 ADDAC3:ADDAC0: Programmable Current Source Select bits 0000 = OFF - all current sources disabled 0001 = 2.25 A 0010 = 4.5 A 0011 = 6.75 A 0100 = 9 A 0101 = 11.25 A 0110 = 13.5 A 0111 = 15.75 A 1000 = 18 A 1001 = 20.25 A 1010 = 22.5 A 1011 = 24.75 A 1100 = 27 A 1101 = 29.25 A 1110 = 31.5 A 1111 = 33.75 A bit 3-0: PCFG3:PCFG0: Port Configuration Selects PCFG3:PCFG2 AN4 AN5 AN6 AN7 00 01 10 11 A A A D A A A D A A D D A D D D PCFG1:PCFG0 AN0 AN1 AN2 AN3 00 01 10 11 A A A D A A A D A A D D A D D D A = Analog input D = Digital I/O Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Note: DS31024A-page 24-4 - n = Value at POR reset On any device reset, all port pins multiplexed with analog functions (ANx pins), are forced to be an analog input. 1997 Microchip Technology Inc. Section 24. Slope A/D Register 24-3: SLPCON Register R/W-0 Resv bit 7 U-0 -- R/W-1 REFOFF R/W-1 Resv U-1 OSCOFF bit 7: Reserved: Always maintain this bit cleared. bit 6: Unimplemented: Read as '0' bit 5: REFOFF: Slope A/D Voltage Reference Power Control bit R/W-1 Resv R/W-1 Resv R/W-1 ADOFF bit 0 1 = Voltage references are disabled (not consuming current) 0 = Voltage references are powered (consuming current) bit 4: Reserved: Always maintain this bit cleared. bit 3: OSCOFF: Slope A/D Oscillator Sleep Control bit 1 = Slope A/D Oscillator is disabled during SLEEP mode (not consuming current) 0 = Slope A/D Oscillator is enabled during SLEEP mode (consuming current) bit 2: Reserved: Always maintain this bit cleared. bit 1: Reserved: Always maintain this bit cleared. bit 0: ADOFF: Slope A/D Power Control bit 1 = Slope A/D is disabled (not consuming current) 0 = Slope A/D is powered (consuming current) Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 24 Slope A/D 1997 Microchip Technology Inc. DS31024A-page 24-5 PICmicro MID-RANGE MCU FAMILY 24.3 Conversion Process There are two methods for performing a conversion. To determine the end of conversion, the first method uses the ADTMR overflow interrupt (OVFIF bit). The second method uses the A/D Capture Interrupt (ADCIF bit). At the end of conversion both bits are used to determine if an overrange condition has occurred. Method 1 uses a fixed conversion time, this means that the capacitor voltage always ramps to the full scale voltage. Immediately after the overflow of the ADTMR, we recommend that the ADRST bit is set to discharge the external capacitor. This will ensure that the residual voltage on the external capacitor, due to dielectric absorption, is independent of input voltage or previous conversions. Method 2 uses a variable conversion time, which results in faster conversions for lower input voltages. Steps for Method 1 ("fixed conversion time"): 1. Initialize the Slope A/D module: a)Clear the REFOFF bit (SLPCON<5>) b)Clear the ADOFF bit (SLPCON<0>) c)Initialize ADCON1<7:4> to select the programmable current source. 2. Set the ADRST bit (ADCON0<1>), until the ramp capacitor reaches ground. This is capacitor dependent. A minimum of 200 s is recommended. 3. Select Input Channel 4. Clear the OVFIF and ADCIF bits. 5. Initialize Slope A/D Timer (ADTMR). ADTMR value depends on bits of resolution required (see Table 24-1). 6. To start a conversion, clear the ADRST bit, this allows the ramp capacitor to begin charging and the ADTMR to increment. 7. Conversion is complete when the Slope A/D timer (ADTMR) overflows from FFFFh to 0000h. This causes the OVFIF bit to be set. 8. Check if the ADCIF bit is set. If this bit is set, the value in the capture register ADCAP is valid. This method depends on minimum latency to verify the capture interrupt flag bit after the ADTMR overflows. If the ADCIF bit is cleared, then the input voltage was out of the A/D input range. 9. Set the ADRST bit (ADCON0<1>) to stop ADTMR and discharge external capacitor 10. Do Conversion Calculations 11. Goto Step 2 DS31024A-page 24-6 1997 Microchip Technology Inc. Section 24. Slope A/D Steps for Method 2 ("variable conversion time"): 1. Initialize the Slope A/D module: a)Clear the REFOFF bit (SLPCON<5>). b)Clear the ADOFF bit (SLPCON<0>). c)Initialize ADCON1<7:4> to select the programmable current source. 2. Set the ADRST bit (ADCON0<1>), until the ramp capacitor reaches ground. This is capacitor dependent. A minimum of 200 s is recommended. 3. Select Input Channel. 4. Clear the OVFIF and ADCIF bits. 5. Initialize Slope A/D Timer (ADTMR). ADTMR value depends on bits of resolution required (see Table 24-1). 6. To start a conversion, clear the ADRST bit, this allows the ramp capacitor to begin charging and the ADTMR to increment. 7. Conversion is complete when the ramp voltage exceeds the analog input so the comparator output changes from high to low. This causes the ADCIF bit to be set. 8. Check if the ADTMR did not increment more counts than the maximum resolution allowed. If there were more counts, then the input voltage was out of the A/D input range. 9. Set the ADRST bit (ADCON0<1>) to stop ADTMR and discharge external capacitor 10. Do Conversion Calculations. 11. Go to Step 2. Note: The Slope A/D timer continues to run following a capture event. The maximum Slope A/D timer count is 65,536. It can be clocked by the on-chip or external oscillator. At a 4 MHz oscillation frequency, the maximum conversion time is 16.38 ms for a full count. A typical conversion should complete before full-count is reached. The timer overflow flag is set once the timer rolls over (FFFFh to 0000h), and an interrupt occurs, if enabled. End-user calibration is simplified or eliminated by making use of the on-chip EPROM. Internal component values are measured at factory final test and stored in the memory for use by the application firmware. Periodic conversion cycles should be performed on the bandgap and slope references (described in Subsection 24.4 "Other Analog Modules" ) to compensate for Slope A/D component drift. Measurements for the reference voltage counts are equated to the voltage value stored into EPROM during calibration. Since all measurements are relative to the reference, offset voltages inherent in the comparator are minimized. The Slope A/D clock source does not require a precise frequency, only a stable frequency. 1997 Microchip Technology Inc. DS31024A-page 24-7 Slope A/D See AN624, "PIC14000 Slope A/D Theory and Implementation" for further details of Slope A/D operation. 24 PICmicro MID-RANGE MCU FAMILY 24.3.1 Slope A/D Timer (ADTMR) The Slope A/D timer (ADTMR) is comprised of a 16-bit timer (ADTMRH:ADTMRL), which is incremented every oscillator cycle. The ADTMR registers are cleared by a power-on reset; otherwise the software must initialize it after each conversion. A separate 16-bit capture register (ADCAPH:ADCAPL) is used to capture the ADTMR count if a Slope A/D capture event occurs (see below). Both the Slope A/D timer and capture registers are readable and writable. The 16-bit timer is a read/write register and is cleared on any device reset. Note 1: Reading or writing the ADTMR register during an Slope A/D conversion cycle can produce unpredictable results and is not recommended. Note 2: The correct sequence for writing the ADTMR register is HI byte followed by LO byte. Reversing this order will prevent the Slope A/D timer from running. During a conversion one or both of the following events will occur: * capture event * timer overflow In a capture event, the comparator trips when the slope voltage on the CDAC output exceeds the input voltage from the selected Slope A/D channel, causing the comparator output to transition from high to low. This causes a transfer of the current timer count to the capture register and sets the ADCIF flag bit. An interrupt will be generated if the ADCIE bit is set (interrupt enabled). In addition, GIE and PIE bits must be set. Software is responsible for clearing the ADCIF flag bit prior to the next conversion cycle. This interrupt can only occur once per conversion cycle. In a timer overflow condition, the timer rolls over from FFFFh to 0000h, and a capture overflow flag (OVFIF) is asserted. The timer continues to increment following a timer overflow. An interrupt can be generated if bit OVFIE is set (interrupt enabled). In addition, the GIE and PIE bits must be set. Software is responsible for clearing the OVFIF flag bit prior to the next conversion cycle. Figure 24-2: Example Slope A/D Conversion Cycle CAPTURE CLK ADTMR INCREMENTS ADRST ADCON0<1> ADTMR COUNT XX XX+1 XX+2 XX+3 COMPARE CDAC ADCIF Capture Register DS31024A-page 24-8 XX+8 XX+9 (must be cleared by software) XX XX+8 1997 Microchip Technology Inc. Section 24. Slope A/D 24.3.2 Sleep Operation The Slope A/D may operate when the device is in Sleep mode. For the Slope A/D to do a conversion during Sleep mode, the Slope A/D module must have a device clock. For a clock to be present the OSCOFF bit must be cleared before going to SLEEP. Also the REFOFF and ADOFF bits must be cleared to ensure that the results reflect the voltage on the input channel. By doing an A/D conversion during Sleep mode, the result has improved accuracy due to a reduction of system noise. When the device clock is disabled, the Slope A/D Timer (ADTMRH:ADTMRL) stops incrementing. Even if the Slope A/D module is not disabled, the slope A/D cannot wake-up the device. This is because the ADCIF bit cannot be set, which is one of the control bits used to wake the device from SLEEP mode. When the device awakes, if the comparator value has tripped, the capture and interrupt will occur. The value in the ADCAP registers is meaningless. For maximum power savings, all analog components of the Slope A/D module should be disabled (no conversion in progress). 24.3.3 Effects of a Reset After any device reset, the Slope A/D module is disabled (lowest current state) and the device I/O are configured as analog channels. 24.3.4 Slope A/D Comparator This module includes a high gain comparator for Slope A/D conversions. The non-inverting input terminal of the Slope A/D comparator is connected to the output of an analog MUX through an RC low-pass filter. The inverting input terminal is connected to the external ramp capacitor. The output of the comparator is used to cause the capture event to occur. This causes the value in the ADTMR registers to be loaded into the ADCAP registers. This output will also cause the ADCIF bit to be set. 24.3.5 Analog MUX A total of 16 channels are internally multiplexed to the single Slope A/D comparator positive input. Four configuration bits (ADCON0<7:4>) select the channel to be converted. 24.3.6 Programmable Current Source Four configuration bits (ADCON1<7:4>) are used to control a programmable current source for generating the ramp voltage to the Slope A/D comparator. This allows compensation for full-scale input voltage, clock frequency and the external capacitor tolerance variations. 24 Setting the ADRST bit disconnects the current source from the CDAC pin. Current flow begins when the ADRST bit is cleared. 1997 Microchip Technology Inc. DS31024A-page 24-9 Slope A/D The programmable current source output is tied to the CDAC pin. This current source is used to charge an external capacitor, which generates the ramp voltage for the Slope A/D comparator (Figure 24-1). PICmicro MID-RANGE MCU FAMILY 24.3.7 Slope A/D Resolution, Speed, Voltage Range, and Capacitor Selection The Slope A/D module allows many trade-offs. For a conversion the user needs to make the following Trade-offs: * * * * The Resolution of the Result The Speed of the Conversion The Analog Input Voltage Range The External Capacitor The resolution is the number of bits that is used by the ADTMR to represent the measured input voltage. This resolution affects the time that the conversion can be completed in. Table 24-1 shows the trade-off between the resolution of the conversion and the maximum conversion time. The conversion time for the Slope A/D converter can be calculated using the equation: Conversion Time = (1/Fosc) x 2N Where Fosc is the oscillator frequency and N is the number of bits of resolution desired. Therefore at 4 MHz, the conversion time for 16 bits is 16.384 msec. Conversely, it is 256 sec for 10-bits. Table 24-1: ADTMR Initialization Values and Conversion Times Maximum Conversion Time Resolution Bits Value Loaded into ADTMR Cycles 20 MHz 4 MHz 16 15 14 13 12 11 10 0000h 8000h C000h E000h F000h F800h FC00h 65536 TOSC 32768 TOSC 16384 TOSC 8192 TOSC 4096 TOSC 2048 TOSC 1024 TOSC 3.28 ms 1.64 ms 820 s 410 s 204.8 s 102.4 s 51.2 s 16.38 ms 8.2 ms 4.1 ms 2.05 ms 1.03 ms 500 s 250 s . DS31024A-page 24-10 1997 Microchip Technology Inc. Section 24. Slope A/D The selection of the external capacitor is determined by the desired characteristics of the application. These include * Input Voltage Range (widest range of all input channels) * Conversion Time * Programmable Current Source Output Values The selection of these values should be done to minimize the time between a comparator trip (ADCIF bit is set) to the ADTMR overflow (OVFIF is set). This ensures that the entire range of the ADTMR is used for the A/D conversion process. The equation for selecting the ramp capacitor value is: Capacitor = (conversion time in seconds) X (current source output in amps) / (full scale in volts) Table 24-2 provides example capacitor values for the desired Slope A/D resolution, conversion time, and full scale voltage measurement. This capacitor on the CDAC pin should have a low voltage-coefficient as found in teflon, polypropylene, or polystyrene capacitors, for optimum results. This external capacitor must be discharged at the beginning of each conversion cycle by setting the ADRST bit (ADCON0<1>). The time for the ADRST bit to be set depends on the characteristics of the external capacitor for a complete discharge. Table 24-2: External Capacitor Selection (@ 4 MHz) Slope A/D Conversion Resolution Time (ms) (Bits) 16 16.384 14 4.096 12 1.024 10 0.256 Full Scale (Volts) 3.5 2.0 1.5 3.5 2.0 1.5 3.5 2.0 1.5 3.5 2.0 1.5 Slope A/D Current Source Select ADDAC3:ADDC0 Typical Output (amps) Calculated CDAC Capacitor CDAC Capacitor Nearest Standard Value 1100 1010 1011 1101 1011 1100 1101 1001 1010 1011 1010 1011 27 22.5 24.75 29.25 24.75 27 29.25 20.25 22.5 24.75 22.5 24.75 0.126 F 0.184 F 0.270 F 34 nF 50.7 nF 73.7 nF 8.56 nF 10.4 nF 15.4 nF 1.81 nF 2.88 nF 4.22 nF 0.12 F 0.18 F 0.27 F 33 nF 47 nF 68 nF 8.2 nF 10 nF 15 nF 1.8 nF 2.7 nF 3.9 nF 1997 Microchip Technology Inc. Slope A/D . 24 DS31024A-page 24-11 PICmicro MID-RANGE MCU FAMILY 24.4 Other Analog Modules Additional analog modules for mixed signal applications are required. These include: * bandgap voltage reference * slope reference voltage divider 24.4.1 Bandgap Voltage Reference The bandgap reference circuit is used to generate a 1.2V nominal stable voltage reference for the Slope A/D, the low-voltage detector, and the slope reference divider. The bandgap reference voltage is available on the analog MUX. To enable the bandgap reference REFOFF (SLPCON<5>) must be cleared. The bandgap reference must be enabled for any slope A/D conversion. The bandgap reference calibration factor is stored in the calibration space EPROM. 24.4.2 Slope Reference Voltage Divider The slope reference voltage divider circuit, consisting of a buffer amplifier and resistor divider, is connected to the internal bandgap reference producing two other voltage references called SREFHI and SREFLO (see Figure 24-3). SREFHI is nominally the same as the bandgap voltage, 1.2V, and SREFLO is nominally 0.13V. These reference voltages are available on two of the analog multiplexer channels. The Slope A/D module and firmware can measure the SREFHI and SREFLO voltages, and in conjunction with the KREF and KBG calibration data correct for the ADC's offset and slope errors. See AN624 for further details. Figure 24-3: Slope Reference Divider ADOFF (SLPCON<0>) VREF Bandgap Reference + _ SREFHI To Slope A/D MUX REFOFF (SLPCON<5>) SREFLO ~ KREF DS31024A-page 24-12 = SREFLO SREFHI 9 SREFLO SREFHI - SREFLO 1997 Microchip Technology Inc. Section 24. Slope A/D 24.5 Calibration Parameters The Slope A/D module has several analog components. Like all CMOS circuitry the parametric values vary with process, temperature, voltage, and time. Devices have been designed to minimize the effect of these variations. In addition, each device, with the slope A/D module, is calibrated at factory test by measuring several key parameters and storing these values into EPROM at specified locations. The customer's application program may access this data and use it to mathematically compensate for device variations. Collectively, these data values are referred to as calibration constants. The calibration constants are listed in Table 24-3. The 32-bit floating point representation has an exponent byte, and three bytes of mantissa. For information on floating point algorithms, refer to AN575. Table 24-3: Calibration Constants Parameter A/D Slope reference ratio Bandgap reference voltage Symbol Number of Bytes Representation of Value KREF KBG 4 4 32-bit Floating Point 32-bit Floating Point For additional information on using the calibration parameters see Application Note 624. 24.5.1 Using Calibration Data The calibration constants should be used by the application firmware to obtain the best accuracy. KREF and KBG are used in A/D conversions. 24.5.2 Parameter Variation Table 24-4 lists the "Maximum Parameter Variation" attainable when the calibration data is not used as well as the "Expected Parameter Variation with Calibration." If the accuracies without calibration are adequate for the task at hand, no further calibrations of the module are necessary. If greater accuracy is needed, the calibration constants must be used. Table 24-4: Parameter Variation Symbol KREF KBG Parameter A/D slope reference ratio Bandgap reference voltage Device Programming 24.5.3.1 Non-Windowed Parts +/- 2.2% +/- 4.2% Achievable Variation with Calibration +/- 0.13% +/- 0.058% Non-windowed parts are programmed just like any PIC16CXXX processor. The calibration area is write-protected during factory calibration. 24.5.3.2 Windowed Parts Caution: Windowed parts must not be write-protected. If the parts are erased by ultraviolet light, the calibration parameters are lost and cannot be reprogrammed once the part has been write-protected. Calibration data must be read out and saved before erasing a windowed part. There is no way to recreate these values, so if they are lost the part can no longer be calibrated. 1997 Microchip Technology Inc. DS31024A-page 24-13 24 Slope A/D 24.5.3 Maximum Variation Without Calibration PICmicro MID-RANGE MCU FAMILY 24.6 Design Tips Question 1: What are some recommended Capacitor types? Answer 1: Polypropylene film capacitor is a good trade-off between cost, availability and performance Question 2: Can you suggest some sources for Capacitors Answer 2: A source is: Southern Electronics Company Telephone: (203) 876-7488 Question 3: I used the recommended capacitor and Programmable Current Source from Table 24-2, and my A/D input range does not match. Answer 3: That table is meant to be a good starting point, but does not include variation that is the result of the device not operating at exactly 4 MHz; tolerance of the external capacitor and variations of the Programmable Current Source, due to process and application temperature. A conversion on the Bandgap Reference can be used to judge how to adjust the Programmable Current Source Output to ensure proper A/D full scale conversions. Example code (routine ad_optimize, in P14_RV10.ASM) for this adjustment is available with the PICDEM-14A Demo Board, and may be also available on the Microchip web site. Question 4: I am using the PIC14C000 which also has the on-chip Temperature sensor. The sensor results seem to be a little high. Answer 4: This may be caused by self heating of the DIE. Self heating of the DIE may be caused by a few things, including: * I/O sinking and/or sourcing significant amount of current * Power dissipation of the device running (remember the PIC14C000 can operate in sleep mode) * Package type due to junction to ambient temperature coefficient of package For best results the power dissipation should be kept low. Calibration is performed with the device in a low power state. Question 5: My A/D conversion results seem affected by the operation of high current components on my board. What can I do to minimize this? Answer 5: The high current components on your board may cause the ground potential difference across the ground trace or ground plane. To minimize this effect, you should employ two system grounds on the application board. The first ground, analog ground, used for the reference analog signals (Slope A/D external capacitor ground, Resistor Divider ground, and etc.). No high current nor any digital power returns should go through this analog ground system. The second ground, digital ground, is used for all other digital logic in the system. The application's digital logic will inject noise onto this ground. Proper grounding techniques should be used to minimize this noise. These two grounds are connected at the PICmicro's ground pin. Ideally the two grounds are implemented using separate ground planes. In most cases, this can still be implemented on a two layer board. One layer is used for both ground systems, where the two planes are separated by a gap. The second layer is used as the trace layer. DS31024A-page 24-14 1997 Microchip Technology Inc. Section 24. Slope A/D 24.7 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Slope A/D are: Title Application Note # PIC14C000 Calibration Parameters AN621 PIC14C000 A/D Theory and Implementation AN624 Lead Acid Battery Charger Implementation using the PIC14C000 AN626 24 Slope A/D 1997 Microchip Technology Inc. DS31024A-page 24-15 PICmicro MID-RANGE MCU FAMILY 24.8 Revision History Revision A This is the initial released revision of the Slope A/D module description. DS31024A-page 24-16 1997 Microchip Technology Inc. M Section 25. LCD HIGHLIGHTS This section of the manual contains the following major topics: 25.1 Introduction ..................................................................................................................25-2 25.2 Control Register ...........................................................................................................25-3 25.3 LCD Timing ..................................................................................................................25-6 25.4 LCD Interrupts............................................................................................................25-12 25.5 Pixel Control...............................................................................................................25-13 25.6 Voltage Generation ....................................................................................................25-15 25.7 Operation During Sleep .............................................................................................25-16 25.8 Effects of a Reset.......................................................................................................25-17 25.9 Configuring the LCD Module......................................................................................25-17 25.10 Discrimination Ratio ...................................................................................................25-18 25.11 LCD Voltage Generation ............................................................................................25-20 25.12 Contrast .....................................................................................................................25-22 25.13 LCD Glass..................................................................................................................25-22 25.14 Initialization ................................................................................................................25-23 25.15 Design Tips ................................................................................................................25-24 25.16 Related Application Notes..........................................................................................25-25 25.17 Revision History .........................................................................................................25-26 25 LCD 1997 Microchip Technology Inc. DS31025A page 25-1 PICmicro MID-RANGE MCU FAMILY 25.1 Introduction The LCD module generates the timing control to drive a static or multiplexed LCD panel, with support for up to 32 segments multiplexed with up to four commons. It also provides control of the LCD pixel data. The interface to the module consists of three control registers (LCDCON, LCDSE, and LCDPS) used to define the timing requirements of the LCD panel and up to 16 LCD data registers (LCD00-LCD15) that represent the array of the pixel data. In normal operation, the control registers are configured to match the LCD panel being used. Primarily, the initialization information consists of selecting the number of commons and segments required by the LCD panel, and then specifying the LCD Frame clock rate to be used by the panel. Once the module is initialized for the LCD panel, the individual bits of the LCD data registers are cleared/set to represent a turned-on pixel respectively. Once the module is configured, the LCDEN bit (LCDCON<7>) is used to enable or disable the LCD module. The LCD panel can also operate during sleep by clearing the SLPEN bit (LCDCON<6>). Figure 25-1: LCD Module Block Diagram Data Bus LCD RAM 32 x 4 128 to SEG<31:0> TO I/O PADS 32 MUX Timing Control LCDCON COM3:COM0 LCDPS TO I/O PADS LCDSE Internal RC osc T1CKI Fosc/4 DS31025A-page 25-2 Clock Source Select and Divide 1997 Microchip Technology Inc. Section 25. LCD 25.2 Control Register Register 25-1: LCDCON Register R/W-0 LCDEN bit 7 R/W-0 SLPEN U-0 -- R/W-0 VGEN R/W-0 CS1 R/W-0 CS0 R/W-0 LMUX1 bit 7 LCDEN: Module Drive Enable bit 1 = LCD drive enabled 0 = LCD drive disabled bit 6 SLPEN: LCD Display Sleep Enable bit 1 = LCD module will stop operating during SLEEP 0 = LCD module will continue to display during SLEEP bit 5 Unimplemented: Read as '0' bit 4 VGEN: Voltage Generator Enable bit 1 = Internal LCD Voltage Generator Enabled, (powered-up) 0 = Internal LCD Voltage Generator powered-down, voltage is expected to be provided externally bit 3:2 CS1:CS0: Clock Source Select bits 00 = Fosc/256 01 = T1CKI (Timer1) 1x = Internal RC oscillator bit 1:0 LMUX1:LMUX0: Common Selection bits Specifies the number of commons and the bias method LMUX1:LMUX0 00 01 10 11 MULTIPLEX Static 1/2 1/3 1/4 (COM0) (COM0, 1) (COM0, 1, 2) (COM0, 1, 2, 3) R/W-0 LMUX0 bit 0 BIAS Max # of Segments Static 1/3 1/3 1/3 32 31 30 29 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-3 PICmicro MID-RANGE MCU FAMILY Register 25-2: LCDPS Register U-0 -- bit 7 U-0 -- U-0 -- U-0 -- bit 7:4 Unimplemented, read as '0' bit 3:0 LP3:LP0: Frame Clock Prescale Selection bits R/W-x LP3 R/W-x LP2 R/W-x LP1 LMUX1:LMUX0 Multiplex 00 Static Clock source / (128 * (LP3:LP0 + 1)) 01 1/2 Clock source / (128 * (LP3:LP0 + 1)) 10 1/3 Clock source / ( 96 * (LP3:LP0 + 1)) 11 1/4 Clock source / (128 * (LP3:LP0 + 1)) R/W-x LP0 bit 0 Frame Frequency = Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Register 25-3: - n = Value at POR reset Generic LCDD (Pixel Data) Register Layout R/W-x SEGs COMc bit 7 bit 7:0 R/W-x SEGs COMc R/W-x SEGs COMc R/W-x SEGs COMc R/W-x SEGs COMc R/W-x SEGs COMc R/W-x SEGs COMc R/W-x SEGs COMc bit 0 SEGsCOMc: Pixel Data bit for segment s and common c 1 = Pixel on (dark) 0 = Pixel off (clear) Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' DS31025A-page 25-4 - n = Value at POR reset 1997 Microchip Technology Inc. Section 25. LCD Register 25-4: LCDSE Register R/W-1 SE29 bit 7 bit 7 R/W-1 SE27 R/W-1 SE20 R/W-1 SE16 R/W-1 SE12 R/W-1 SE9 R/W-1 SE5 R/W-1 SE0 bit 0 SE29: Pin Function Select bits for COM1/SEG31 - COM3/SEG29 1 = pins have LCD segment driver function 0 = pins have digital Input function Note: The LMUX1:LMUX0 setting takes precedence over the SE29 bit, causing pins to become common drivers. bit 6 SE27: Pin Function Select for SEG28 and SEG27 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 5 SE20: Pin Function Select bits for SEG26 - SEG20 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 4 SE16: Pin Function Select bits for SEG19 - SEG16 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 3 SE12: Pin Function Select bits for SEG15 - SEG12 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 2 SE9: Pin Function Select bits for SEG11 - SEG09 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 1 SE5: Pin Function Select bits for SEG08 - SEG05 1 = pins have LCD segment driver function 0 = pins have digital Input function bit 0 SE0: Pin Function Select bits for SEG04 - SEG00 1 = pins have LCD segment driver function 0 = pins have digital I/O function Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' Note: - n = Value at POR reset On a Power-on Reset, the LCD pins are configured for LCD drive function. 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-5 PICmicro MID-RANGE MCU FAMILY 25.3 LCD Timing The LCD module has 3 possible clock source inputs and supports static, 1/2, 1/3, and 1/4 multiplexing. 25.3.1 Timing Clock Source Selection The clock sources for the LCD timing generation are: * Internal RC oscillator * Timer1 oscillator * System clock divided by 256 used for device low frequency or sleep operation used for device low frequency or sleep operation The first timing source is an internal RC oscillator which runs at a nominal frequency of 14 kHz. This oscillator provides a lower speed clock which may be used to continue running the LCD while the processor is in sleep. The RC oscillator will power-down when it is not selected or when the LCD module is disabled. The second source is the Timer1 external oscillator. This oscillator provides a lower speed clock which may be used to continue running the LCD while the processor is in sleep. It is assumed that the frequency provided on this oscillator will be 32 kHz. To use the Timer1 oscillator as a LCD module clock source, it is only necessary to set the T1OSCEN (T1CON<3>) bit. The third source is the system clock divided by 256. This divider ratio is chosen to provide about 32 kHz output when the external oscillator is 8 MHz. The divider is not programmable. Instead the LCDPS register is used to set the LCD frame clock rate. The clock sources are selected with bits CS1:CS0 (LCDCON<3:2>). Refer to Figure 25-1 for details of the register programming. TMR1 32 kHz crystal oscillator /4 Static /2 1/2 4-bit Programmable Prescaler /32 COM3 COM2 /256 COM1 FOSC LCD Clock Generation COM0 Figure 25-2: /1,2,3,4 Ring Counter 1/3 1/4 Internal RC oscillator Nominal FRC = 14 kHz LCDPS<3:0> CS1:CS0 LMUX1:LMUX0 LMUX1:LMUX0 internal data bus DS31025A-page 25-6 1997 Microchip Technology Inc. Section 25. LCD 25.3.2 Multiplex Timing Generation The timing generation circuitry will generate 1 to 4 common's based on the display mode selected. The mode is specified by bits LMUX1:LMUX0 (LCDCON<1:0>). Table 25-1 shows the formulas for calculating the frame frequency. Table 25-1: Frame Frequency Formulas Multiplex Frame Frequency = Static Clock source / (128 * (LP3:LP0 + 1)) 1/2 Clock source / (128 * (LP3:LP0 + 1)) 1/3 Clock source / (96 * (LP3:LP0 + 1)) 1/4 Clock source / (128 * (LP3:LP0 + 1)) Table 25-2: Approximate Frame Frequency in Hz using Timer1 @ 32.768 kHz or Fosc @ 8 MHz LP3:LP0 Static 1/2 1/3 1/4 2 85 85 114 85 3 64 64 85 64 4 51 51 68 51 5 43 43 57 43 6 37 37 49 37 7 32 32 43 32 Table 25-3: Approximate Frame Frequency in Hz using internal RC osc @ 14 kHz LP3:LP0 Static 1/2 1/3 1/4 0 109 109 146 109 1 55 55 73 55 2 36 36 49 36 3 27 27 36 27 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-7 PICmicro MID-RANGE MCU FAMILY Figure 25-3: STATIC Waveforms Liquid Crystal Display and Terminal Connection V1 COM0 V0 V1 COM0 SEG0 V0 V1 SEG1 V0 SEG7 V1 COM0-SEG0 V0 (selected pixel waveform) SEG6 -V1 SEG5 COM0-SEG1 DS31025A-page 25-8 V0 1 Frame SEG4 SEG3 SEG2 SEG0 SEG1 (non-selected pixel waveform) 1997 Microchip Technology Inc. Section 25. LCD Figure 25-4: 1/2 MUX, 1/3 BIAS Waveform Liquid Crystal Display and Terminal Connection V3 COM0 V2 V1 V0 COM1 V3 V2 V1 COM0 COM1 V0 V3 V2 SEG3 V1 V0 V3 V2 SEG1 SEG3 SEG2 SEG1 SEG0 V1 V0 V3 V2 V1 COM0-SEG3 V0 (selected pixel waveform) -V1 -V2 -V3 V3 V2 V1 COM0-SEG1 V0 (non-selected pixel waveform) -V1 1 Frame -V2 25 -V3 LCD 1997 Microchip Technology Inc. DS31025A-page 25-9 PICmicro MID-RANGE MCU FAMILY Figure 25-5: 1/3 MUX, 1/3 BIAS Waveform V3 Liquid Crystal Display and Terminal Connection V2 COM0 V1 V0 V3 COM2 V2 COM1 V1 COM1 V0 COM0 V3 V2 COM2 V1 V0 V3 V2 SEG0 V1 V0 SEG0 SEG1 SEG2 V3 V2 SEG2 V1 V0 V3 V2 V1 COM0-SEG0 (non-selected pixel waveform) V0 -V1 -V2 -V3 V3 V2 V1 COM0-SEG2 V0 (selected pixel waveform) -V1 -V2 -V3 1 Frame DS31025A-page 25-10 1997 Microchip Technology Inc. Section 25. LCD Figure 25-6: 1/4 MUX, 1/3 BIAS Waveform Liquid Crystal Display and Terminal Connection COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 V3 V2 V1 V0 SEG0 V3 V2 V1 V0 SEG1 V3 V2 V1 V0 COM3 COM2 COM1 COM0 SEG0 SEG1 V3 V2 V1 V0 -V1 -V2 -V3 COM0-SEG1 (selected pixel waveform) COM0-SEG0 (non-selected pixel waveform) 1 Frame V3 V2 V1 V0 -V1 -V2 -V3 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-11 PICmicro MID-RANGE MCU FAMILY 25.4 LCD Interrupts The LCD timing generation provides an interrupt that defines the LCD frame timing. This interrupt can be used to coordinate the writing of the pixel data with the start of a new frame. Writing pixel data at the frame boundary allows a visually crisp transition of the image. This interrupt can also be used to synchronize external events to the LCD. For example, the interface to an external segment driver, such as a Microchip AY0438, can be synchronized for segment data update to the LCD frame. A new frame is defined to begin at the leading edge of the COM0 common signal. The interrupt will be set immediately after the LCD controller completes accessing all pixel data required for a frame. This will occur at a certain fixed time before the frame boundary as shown in Figure 25-7. The LCD controller will begin to access data for the next frame within TFWR after the interrupt. Figure 25-7: Example Waveforms in 1/4 MUX Drive LCD Interrupt occurs Controller accesses next frame data V3 V2 V1 V0 COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 1 Frame TFINT Frame Boundary TFWR Frame Boundary TFWR = TFRAME/(LMUX1:LMUX0 + 1) TFINT = (TFWR /2 - (2TCY + 40 ns)) min. (TFWR /2 - (1TCY + 40 ns)) max. DS31025A-page 25-12 1997 Microchip Technology Inc. Section 25. LCD 25.5 Pixel Control 25.5.1 LCDD (Pixel Data) Registers The pixel registers contain bits which define the state of each pixel. Each bit defines one unique pixel. Table 25-4 shows the correlation of each bit in the LCDD registers to the respective common and segment signals. Any LCD pixel location not being used for display can be used as general purpose RAM. Table 25-4: LCDD Registers Name LCDD00 LCDD01 LCDD02 LCDD03 LCDD04 LCDD05 LCDD06 LCDD07 LCDD08 LCDD09 LCDD10 LCDD11 LCDD12 LCDD13 LCDD14 LCDD15 Note 1: Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SEG07 SEG06 SEG05 SEG04 SEG03 SEG02 SEG01 SEG00 COM0 COM0 COM0 COM0 COM0 COM0 COM0 COM0 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG09 SEG08 COM0 COM0 COM0 COM0 COM0 COM0 COM0 COM0 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 COM0 COM0 COM0 COM0 COM0 COM0 COM0 COM0 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 COM0 COM0 COM0 COM0 COM0 COM0 COM0 COM0 SEG07 SEG06 SEG05 SEG04 SEG03 SEG02 SEG01 SEG00 COM1 COM1 COM1 COM1 COM1 COM1 COM1 COM1 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG09 SEG08 COM1 COM1 COM1 COM1 COM1 COM1 COM1 COM1 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 COM1 COM1 COM1 COM1 COM1 COM1 COM1 COM1 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 COM1 (1) COM1 COM1 COM1 COM1 COM1 COM1 COM1 SEG07 SEG06 SEG05 SEG04 SEG03 SEG02 SEG01 SEG00 COM2 COM2 COM2 COM2 COM2 COM2 COM2 COM2 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG09 SEG08 COM2 COM2 COM2 COM2 COM2 COM2 COM2 COM2 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 COM2 COM2 COM2 COM2 COM2 COM2 COM2 COM2 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 COM2 (1) COM2 (1) COM2 COM2 COM2 COM2 COM2 COM2 SEG07 SEG06 SEG05 SEG04 SEG03 SEG02 SEG01 SEG00 COM3 COM3 COM3 COM3 COM3 COM3 COM3 COM3 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG09 SEG08 COM3 COM3 COM3 COM3 COM3 COM3 COM3 COM3 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 COM3 COM3 COM3 COM3 COM3 COM3 COM3 COM3 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 COM3 (1) COM3 (1) COM3 (1) COM30 COM3 COM30 COM3 COM3 These pixels do not display, but can be used as general purpose RAM. Value on POR, BOR Value on all other Resets xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-13 PICmicro MID-RANGE MCU FAMILY 25.5.2 Segment Enables The LCDSE register is used to select the pin function for groups of pins. The selection allows each group of pins to operate as either LCD drivers or digital only pins. To configure the pins as a digital port, the corresponding bits in the LCDSE register must be cleared. If the pin is a digital input the corresponding TRIS bit controls the data direction. Any bit set in the LCDSE register overrides any bit settings in the corresponding TRIS register. Note 1: On a Power-on Reset, the LCD pins are configured as LCD drivers. Note 2: The LMUX1:LMUX0 bits take precedence over the LCDSE bit settings for pins RD7, RD6 and RD5. Example 25-1: BCF BSF BCF BCF MOVLW MOVWF STATUS,RP0 STATUS,RP1 LCDCON,LMUX1 LCDCON,LMUX0 0xFF LCDSE Example 25-2: BCF BSF BSF BCF MOVLW MOVWF DS31025A-page 25-14 Static MUX with 32 Segments ; ; ; ; ; ; Select Bank2 Select Static MUX Make PortD,E,F,G LCD pins configure rest of LCD 1/3 MUX with 13 Segments STATUS,RP0 STATUS,RP1 LCDCON,LMUX1 LCDCON,LMUX0 0x87 LCDSE ; ; ; ; ; ; Select Bank2 Select 1/3 MUX Make PORTD<7:0> & PORTE<6:0> LCD pins configure rest of LCD 1997 Microchip Technology Inc. Section 25. LCD 25.6 Voltage Generation There are two methods for LCD voltage generation, internal charge pump, or external resistor ladder. 25.6.1 Charge Pump The LCD charge pump is shown in Figure 25-8. The 1.0V - 2.3V regulator will establish a stable base voltage from the varying battery voltage. This regulator is adjustable through the range by connecting a variable external resistor from VLCDADJ to ground. The potentiometer provides contrast adjustment for the LCD. This base voltage is connected to VLCD1 on the charge pump. The charge pump boosts VLCD1 into VLCD2 = 2 * VLCD1 and VLCD3 = 3 * VLCD1. When the charge pump is not operating, VLCD3 will be internally tied to VDD. See the Electrical Specifications section for charge pump capacitor and potentiometer values. 25.6.2 External R-Ladder The LCD module can also use an external resistor ladder (R-Ladder) to generate the LCD voltages. Figure 25-8 shows external connections for static and 1/3 bias. The VGEN (LCDCON<4>) bit must be cleared to use an external R-Ladder. Figure 25-8: Charge Pump and Resistor Ladder Block Diagram VDD 10 A nominal LCDEN Charge Pump VLCD3 VLCDADJ 100k(2) VLCD2 VLCD1 0.47 F(2) 0.47 F(2) SLPEN C1 C2 0.47 F(2) 130k(2) 0.47 F(2) 10k* (1) 10k(2) (1) VDD 10k(2) (1) VDD 10k* External connections for internal charge pump, VGEN = 1. (1) 5k(2) External connections for external R-ladder, 1/3 Bias, VGEN = 0. 5k(2) External connections for external R-ladder, Static Bias, VGEN = 0. 1997 Microchip Technology Inc. DS31025A-page 25-15 LCD Note 1: Location of optional filter capacitor. 2: These values are provided for design guidance only and should be optimized to the application by the designer. 25 PICmicro MID-RANGE MCU FAMILY 25.7 Operation During Sleep The LCD module can operate during sleep. The selection is controlled by bit SLPEN (LCDCON<6>). Setting the SLPEN bit allows the LCD module to go to sleep. Clearing the SLPEN bit allows the module to continue to operate during sleep. If a SLEEP instruction is executed and SLPEN = '1', the LCD module will cease all functions and go into a very low current consumption mode. The module will stop operation immediately and drive the minimum LCD voltage on both segment and common lines. Figure 25-9 shows this operation. To ensure that the LCD completes the frame, the SLEEP instruction should be executed immediately after a LCD frame boundary. The LCD interrupt can be used to determine the frame boundary. See 25.4 "LCD Interrupts" for the formulas to calculate the delay. If a SLEEP instruction is executed and SLPEN = '0', the module will continue to display the current contents of the LCDD registers. To allow the module to continue operation while in sleep, the clock source must be either the internal RC oscillator or Timer1 external oscillator. While in sleep, the LCD data cannot be changed. The LCD module current consumption will not decrease in this mode, however the overall consumption of the device will be lower due to shutdown of the core and other peripheral functions. Note: The internal RC oscillator or external Timer1 oscillator must be used to operate the LCD module during sleep. Figure 25-9:Sleep Entry/exit When SLPEN = 1 or CS1:CS0 = 00 3/3V Pin COM0 2/3V 1/3V 0/3V 3/3V Pin COM1 2/3V 1/3V 0/3V 3/3V 2/3V Pin COM3 1/3V 0/3V 3/3V 2/3V Pin SEG0 1/3V 0/3V interrupted frame SLEEP instruction execution DS31025A-page 25-16 Wake-up 1997 Microchip Technology Inc. Section 25. LCD 25.8 Effects of a Reset The LCD module is disabled, but the LCD pins are configured as LCD drivers. This ensures that the microcontroller does not damage the LCD glass by accidently having a DC voltage across a segment. 25.9 Configuring the LCD Module The following is the sequence of steps to follow to configure the LCD module. 1. 2. 3. 4. 5. 6. Select the frame clock prescale using the LP3:LP0 bits (LCDPS<3:0>). Configure the appropriate pins to function as segment drivers using the LCDSE register. Configure the LCD module for the following using the LCDCON register. Multiplex mode and Bias, selected by the LMUX1:LMUX0 bits Timing source, selected by the CS1:CS0 bits Voltage generation, enabled by the VGEN bit Sleep mode operation, enabled by the SLPEN bit Write initial values to pixel data registers, LCDD00 through LCDD15. Clear LCD interrupt flag bit, LCDIF, and if desired, enable the interrupt by setting the LCDIE bit. Enable the LCD module, by setting the LCDEN bit (LCDCON<7>). 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-17 PICmicro MID-RANGE MCU FAMILY 25.10 Discrimination Ratio Discrimination ratio is a way to calculate the contrast levels that a panel can achieve. The first example is a static waveform from Figure 25-3. The voltages V1 and V0 will be assigned values of 1 and 0. The next step is to construct an equation for one frame to help visualize the DC and RMS voltages present on an individual pixel that is ON and OFF. The rest of the following shows the calculation of the DC, RMS, and Discrimination Ratio. Example 25-3: Discrimination Ratio Calculation for Static MUX COMx - SEGx [ON] = 1 - 1, VDC = 0 COMx - SEGx [OFF] = 0 + 0, VDC = 0 VRMS [ON] = V (1)2 + (-1)2 2 = 1V VRMS [OFF] = V (0)2 + (0)2 2 = 0V D = VRMS [ON] VRMS [OFF] = 1V 0V = See Figure 25-3 for Static waveform. DS31025A-page 25-18 1997 Microchip Technology Inc. Section 25. LCD The next example is for Figure 25-6 which is a 1/4 MUX, 1/3 BIAS waveform. For this example, the values 3, 2, 1 and 0 will be assigned to V3, V2, V1, and V0 respectively. The frame equation, DC voltage, RMS voltage and discrimination ratio calculations are shown in Example 25-4. Example 25-4: COM0 - SEGx [ON] = COM0 - SEGx [OFF] = 3-3+1-1+1-1+1-1 1-1-1+1-1+1-1+1 VDC = 0 VDC = 0 VRMS [ON] = V (3)2 + (-3)2 + (1)2 + (-1)2 + (1)2 + (-1)2 + (1)2 + (-1)2 8 = 3 V VRMS [OFF] = V (1)2 + (-1)2 + (-1)2 + (1)2 + (-1)2 + (1)2 + (-1)2 + (1)2 8 = V D = VRMS [ON] VRMS [OFF] Note: Discrimination Ratio Calculation 1/4 MUX = 3 V 1 V = 1.732 Refer to Figure 25-6 As shown in these examples, static displays have excellent contrast. The higher the multiplex ratio of the LCD, the lower the discrimination ratio, and therefore, the lower the contrast of the display. Table 25-5 shows the VOFF, VON and discrimination ratios of the various combinations of MUX and BIAS. As the multiplex of the LCD panel increases, the discrimination ratio decreases. The contrast of the panel will also decrease, so to provide better contrast the LCD voltages must be increased to provide greater separation between each level. Table 25-5: Discrimination Ratio vs. MUX and Bias 1/3 BIAS VOFF VON D STATIC 0 1 1/2 MUX 0.333 0.745 2.236 1/3 MUX 0.333 0.638 1.915 1/4 MUX 0.333 0.577 1.732 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-19 PICmicro MID-RANGE MCU FAMILY 25.11 LCD Voltage Generation Among the many ways to generate LCD voltage, two methods stand out above the crowd: * resistor ladder * charge pump. The resistor ladder method, shown in Figure 25-10, is most commonly used for higher VCC voltages. This method uses inexpensive resistors to create the multi-level LCD voltages. Regardless of the number of pixels that are energized the current remains constant. The voltage at point V3 is typically tied to VCC, either internally or externally. The resistance values are determined by two factors: display quality and power consumption. Display quality is a function of the LCD drive waveforms. Since the LCD panel is a capacitive load, the waveform is distorted due to the charging and discharging currents. This distortion can be reduced by decreasing the value of resistance. However, this change increases the power consumption due to the increased current now flowing through the resistors. As the LCD panel increases in size, the resistance value must be decreased to maintain the image quality of the display. Sometimes the addition of parallel capacitors to the resistance can reduce the distortion caused by charging/discharging currents. The capacitors act as charge storage to provide current as the display waveform transitions. In general, R is 1 k to 50 k and the potentiometer is 5 k to 200 k. Figure 25-10: Resistor Ladder V3 R V2 R V1 R V0 Figure 25-11: Resistor Ladder with Capacitors +5V V3 R C R C R C V2 V1 V0 DS31025A-page 25-20 1997 Microchip Technology Inc. Section 25. LCD A charge pump is ideal for low voltage battery operation because the VDD voltage can be boosted up to drive the LCD panel. The charge pump requires a charging capacitor and filter capacitor for each of the LCD voltages as seen in Figure 25-12. These capacitors are typically low leakage types such as polyester, polypropylene, or polystyrene material. Another feature that makes the charge pump ideal for battery applications is that the current consumption is proportional to the number of pixels that are energized. Figure 25-12: Charge Pump C1 C2 V3 V2 V1 V0 VADJ 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-21 PICmicro MID-RANGE MCU FAMILY 25.12 Contrast Although contrast is heavily dependent on the light source available and the multiplex mode, it also varies with the LCD voltage levels. As previously seen, a potentiometer is used to control the contrast of the LCD panel. The potentiometer sets the separation between each of the LCD voltages. The larger the separation, the better the contrast achievable. 25.13 LCD Glass The characteristics of the LCD glass vary depending on the materials used. Appendix B gives a list of some LCD manufacturers. Please contact them for the characteristics of your desired glass. DS31025A-page 25-22 1997 Microchip Technology Inc. Section 25. LCD 25.14 Initialization Example 25-5 shows the code for initializing the LCD module with all segments cleared. Example 25-5: BCF BCF BSF MOVLW MOVWF MOVLW MOVWF MOVLW MOVWF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF CLRF BSF BSF BCF LCD Initialization Code PIR1,LCDIF STATUS,RP0 STATUS,RP1 0x06 LCDPS 0xff LCDSE 0x17 LCDCON LCDD00 LCDD01 LCDD02 LCDD03 LCDD04 LCDD05 LCDD06 LCDD07 LCDD08 LCDD09 LCDD10 LCDD11 LCDD12 LCDD13 LCDD14 LCDD15 PIE1,LCDIE LCDCON,LCDEN STATUS,RP1 ; Clear LCD interrupt flag ; Go to Bank2 ; Set frame freq to ~37Hz ; Make all pin functions LCD drivers ; Drive during SLEEP, Charge pump enabled ; Timer1 clock source, 1/4 MUX ; Clear all data registers to turn ; all pixels off ; Enable LCD interrupts ; Enable LCD Module ; Go to Bank0 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-23 PICmicro MID-RANGE MCU FAMILY 25.15 Design Tips Question 1: I'm trying to use some of the LCD pins as inputs. Answer 1: Ensure that you have the control bits in the LCDSE properly configured, since these bits override the TRIS bits. Question 2: My LCD panel is flickering. Answer 2: Your frame frequency may be too low. The frame frequency can be changed in the LCDPS register. Question 3: The LCD segments are not very visible. Answer 3: This may be due to misadjusted LCD voltage, some possibilities include: 1. 2. DS31025A-page 25-24 If you are using the R-ladder, try different values of R, vary the R-ladder potentiometer. The VLCDADJ pin should be connected to ground. If you are using the charge pump, adjust the resistance value on the VLCDADJ pin. 1997 Microchip Technology Inc. Section 25. LCD 25.16 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the LCD drivers are: Title Application Note # Yet Another Clock Using the PIC16C92X AN649 LCD Fundamentals Using PIC16C92x Microcontrollers AN658 PICDEM3 Demo Board User's Guide DS51079 25 LCD 1997 Microchip Technology Inc. DS31025A-page 25-25 PICmicro MID-RANGE MCU FAMILY 25.17 Revision History Revision A This is the initial released revision of the LCD module description. DS31025A-page 25-26 1997 Microchip Technology Inc. M 26 HIGHLIGHTS This section of the manual contains the following major topics: 26.1 26.2 26.3 26.4 26.5 26.6 26.7 26.8 Introduction ..................................................................................................................26-2 Control Register ...........................................................................................................26-3 Watchdog Timer (WDT) Operation...............................................................................26-4 SLEEP (Power-Down) Mode........................................................................................26-7 Initialization ..................................................................................................................26-9 Design Tips ................................................................................................................26-10 Related Application Notes..........................................................................................26-11 Revision History .........................................................................................................26-12 1997 Microchip Technology Inc. DS31026A page 26-1 Watchdog Timer and Sleep Mode Section 26. Watchdog Timer and Sleep Mode PICmicro MID-RANGE MCU FAMILY 26.1 Introduction The Watchdog Timer (WDT) is a free running on-chip RC oscillator which does not require any external components. The block diagram is shown in Figure 26-1. This RC oscillator is separate from the device RC oscillator of the OSC1/CLKIN pin. This means that the WDT will run, even if the clock on the OSC1 and OSC2 pins has been stopped, for example, by execution of a SLEEP instruction. The Watchdog Timer (WDT) is enabled/disabled by a device configuration bit. If the WDT is enabled, software execution may not disable this function. Figure 26-1: Watchdog Timer Block Diagram From TMR0 Clock Source 0 WDT Timer 1 Postscaler M U X 8 8 - to - 1 MUX WDT Enable Bit PS2:PS0 PSA To TMR0 0 1 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION register. DS31026A-page 26-2 1997 Microchip Technology Inc. Section 26. Watchdog Timer and Sleep Mode 26.2 26 Control Register Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. Register 26-1: OPTION_REG Register R/W-1 RBPU (1) bit 7 R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA bit 7 RBPU (1): Weak Pull-up Enable bit 1 = Weak pull-ups are disabled 0 = Weak pull-ups are enabled by individual port latch values bit 6 INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of INT pin 0 = Interrupt on falling edge of INT pin bit 5 T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4 T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module bit 2:0 PS2:PS0: TMR0 Prescaler/WDT Postscaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0 Legend R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset Note 1: Some devices call this bit GPPU. Devices that have the RBPU bit, have the weak pull-ups on PORTB, while devices that have the GPPU have the weak pull-ups on the GP Port. 1997 Microchip Technology Inc. DS31026A-page 26-3 Watchdog Timer and Sleep Mode The OPTION_REG register is a readable and writable register which contains various control bits to configure the TMR0 prescaler/WDT postscaler, the External INT Interrupt, TMR0, and the weak pull-ups on PORTB. PICmicro MID-RANGE MCU FAMILY 26.3 Watchdog Timer (WDT) Operation During normal operation, a WDT time-out generates a device RESET. If the device is in SLEEP mode, a WDT time-out causes the device to wake-up and continue with normal operation, this is known as a WDT wake-up. The WDT can be permanently disabled by clearing the WDTE configuration bit. The postscaler assignment is fully under software control, i.e., it can be changed "on the fly" during program execution. Note: To avoid an unintended device RESET, the following instruction sequence (shown in Example 26-1) must be executed when changing the prescaler assignment from Timer0 to the postscaler of the WDT. This sequence must be followed even if the WDT is disabled. In Example 26-1, the first modification of the OPTION_REG does not need to be included if the final desired prescaler is other then 1:1. If the final prescaler value is 1:1, then a temporary prescale value is set (other than 1:1), and the final prescale value is set in the last modification of the OPTION_REG. This sequence must be followed since the value in the TMR0 prescaler is unknown, and is being used as the WDT postscaler. If the OPTION_REG is changed without this code sequence, the time before a WDT reset is unknown. DS31026A-page 26-4 1997 Microchip Technology Inc. Section 26. Watchdog Timer and Sleep Mode Example 26-1: 26 Changing Prescaler (Timer0WDT) STATUS, RP0 B'xx0x0xxx' OPTION_REG STATUS, RP0 TMR0 STATUS, RP0 B'xxxx1xxx' OPTION_REG b'xxxx1xxx' OPTION_REG STATUS, RP0 ; ; ; ; ; ; ; ; ; ; ; ; Bank1 Select clock source and postscale value other than 1:1 Bank0 Clear TMR0 & Prescaler Bank1 Select WDT, do not change prescale value Clears WDT Select new prescale value and WDT Bank0 To change prescaler from the WDT to the Timer0 module use the sequence shown in Example 26-2. Example 26-2: Changing Prescaler (WDTTimer0) CLRWDT BSF MOVLW MOVWF BCF 1997 Microchip Technology Inc. STATUS, RP0 b'xxxx0xxx' OPTION_REG STATUS, RP0 ; ; ; ; ; Clear WDT and postscaler Bank1 Select TMR0, new prescale value and clock source Bank0 DS31026A-page 26-5 Watchdog Timer and Sleep Mode BSF MOVLW MOVWF BCF CLRF BSF MOVLW MOVWF CLRWDT MOVLW MOVWF BCF PICmicro MID-RANGE MCU FAMILY 26.3.1 WDT Period The WDT has a nominal time-out period of 18 ms, (with no postscaler). The time-out period varies with temperature, VDD and process variations from part to part (see DC specs). If longer time-outs are desired, a postscaler with a division ratio of up to 1:128 can be assigned to the WDT, under software control, by writing to the OPTION_REG register. Thus, time-out periods of up to 2.3 seconds can be realized. The CLRWDT and SLEEP instructions clear the WDT and the postscaler (if assigned to the WDT) and prevent it from timing out and generating a device RESET. The TO bit in the STATUS register will be cleared upon a Watchdog Timer time-out (WDT Reset and WDT wake-up). 26.3.2 WDT Programming Considerations It should also be taken in account that under worst case conditions (VDD = Minimum, Temperature = Maximum, maximum WDT postscaler) it may take several seconds before a WDT time-out occurs. Note: When the postscaler is assigned to the WDT, always execute a CLRWDT instruction before changing the postscale value, otherwise a WDT reset may occur. Table 26-1: Summary of Watchdog Timer Registers Name Bit 7 Bit 6 Bit 5 Bit 4 MPEEN BODEN CP1 CP0 Config. bits OPTION_REG RBPU INTEDG T0CS T0SE Legend: Shaded cells are not used by the Watchdog Timer. DS31026A-page 26-6 Bit 3 Bit 2 Bit 1 Bit 0 PWRTE PSA WDTE PS2 FOSC1 PS1 FOSC0 PS0 1997 Microchip Technology Inc. Section 26. Watchdog Timer and Sleep Mode 26.4 26 SLEEP (Power-Down) Mode If enabled, the Watchdog Timer will be cleared but keeps running, the PD bit in the STATUS register is cleared, the TO bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had, before the SLEEP instruction was executed (driving high, low, or hi-impedance). For lowest current consumption in this mode, all I/O pins should be either at VDD, or VSS, with no external circuitry drawing current from the I/O pin and the modules that are specified to have a delta sleep current should be disabled. I/O pins that are hi-impedance inputs should be pulled high or low externally to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level (VIHMC). Some features of the device that consume a delta sleep current are enabled / disabled by device configuration bits. These include the Watchdog Timer (WDT) and Brown-out Reset (BOR) circuitry modules. 26.4.1 Wake-up from SLEEP The device can wake-up from SLEEP through one of the following events: 1. 2. 3. Any device reset. Watchdog Timer Wake-up (if WDT was enabled). Any peripheral module which can set its interrupt flag while in sleep, such as: - External INT pin - Change on port pin - Comparators - A/D - Timer1 - LCD - SSP - Capture The first event will reset the device upon wake-up. However the latter two events will wake the device and then resume program execution. The TO and PD bits in the STATUS register can be used to determine the cause of device reset. The PD bit, which is set on power-up is cleared when SLEEP is invoked. The TO bit is cleared if WDT wake-up occurred. When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have an NOP after the SLEEP instruction. 1997 Microchip Technology Inc. DS31026A-page 26-7 Watchdog Timer and Sleep Mode Sleep (Power-down) mode is a mode where the device is placed in it's lowest current consumption state. The device oscillator is turned off, so no system clocks are occurring in the device. Sleep mode is entered by executing a SLEEP instruction. PICmicro MID-RANGE MCU FAMILY 26.4.2 Wake-up Using Interrupts When interrupts are globally disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag set, one of the following events will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as an NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bit will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake-up from sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as an NOP. To ensure that the WDT is clear, a CLRWDT instruction should be executed before a SLEEP instruction. Figure 26-2: Wake-up from Sleep Through Interrupt Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT(4) TOST(2) INT pin INTF flag (INTCON<1>) Interrupt Latency(2) GIE bit (INTCON<7>) Processor in SLEEP INSTRUCTION FLOW PC PC Instruction fetched Inst(PC) = SLEEP Instruction executed Inst(PC - 1) PC+1 PC+2 PC+2 Inst(PC + 1) Inst(PC + 2) SLEEP Inst(PC + 1) PC + 2 Dummy cycle 0004h 0005h Inst(0004h) Inst(0005h) Dummy cycle Inst(0004h) Note 1: XT, HS or LP oscillator mode assumed. 2: TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode. 3: GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. 4: CLKOUT is not available in these osc modes, but shown here for timing reference. DS31026A-page 26-8 1997 Microchip Technology Inc. Section 26. Watchdog Timer and Sleep Mode 26.5 26 Initialization Watchdog Timer and Sleep Mode No initialization code at this time. 1997 Microchip Technology Inc. DS31026A-page 26-9 PICmicro MID-RANGE MCU FAMILY 26.6 Design Tips Question 1: My system voltage drops and then returns to the specified device voltage range. The device is not operating correctly and the WDT does not reset and return the device to proper operation. Answer 1: The WDT was not designed to be a recovery from a brown-out condition. It was designed to recover from errant software operation (the device remaining in the specified operating ranges). If your system can be subjected to brown-outs, either the on-chip brown-out circuitry should be enabled or an external brown-out circuit should be implemented. Question 2: Device resets even though I do the CLRWDT instruction in my loop. Answer 2: Make sure that the loop with the CLRWDT instruction meets the minimum specification of the WDT (not the typical). Question 3: Device never gets out of resets. Answer 3: On power-up, you must take into account the Oscillator Start-up time (Tost). Sometimes it helps to put the CLRWDT instruction at the beginning of the loop, since this start-up time may be variable. DS31026A-page 26-10 1997 Microchip Technology Inc. Section 26. Watchdog Timer and Sleep Mode 26.7 26 Related Application Notes Title Power-up Trouble Shooting 1997 Microchip Technology Inc. Application Note # AN607 DS31026A-page 26-11 Watchdog Timer and Sleep Mode This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the WDT and Sleep Mode are: PICmicro MID-RANGE MCU FAMILY 26.8 Revision History Revision A This is the initial released revision of the Watchdog Timer and Sleep mode description. DS31026A-page 26-12 1997 Microchip Technology Inc. M Section 27. Device Configuration Bits HIGHLIGHTS This section of the manual contains the following major topics: Introduction ..................................................................................................................27-2 Configuration Word Bits ...............................................................................................27-4 Program Verification/Code Protection ..........................................................................27-8 ID Locations .................................................................................................................27-9 Design Tips ................................................................................................................27-10 Related Application Notes..........................................................................................27-11 Revision History .........................................................................................................27-12 1997 Microchip Technology Inc. DS31027A page 27-1 Device Configuration Bits 27.1 27.2 27.3 27.4 27.5 27.6 27.7 27 PICmicro MID-RANGE MCU FAMILY 27.1 Introduction The device configuration bits allow each user to customize certain aspects of the device to the needs of the application. When the device powers up, the state of these bits determines the modes that the device uses. Subsection 27.2 "Configuration Word Bits" discusses the configuration bits, and the modes that they can be configured to. These bits are mapped in program memory location 2007h. This location is not accessible during normal device operation (can be accessed only during programming mode). The configuration bits can be programmed (read as '0') or left unprogrammed (read as '1') to select various device configurations. The ability to change these settings once they have been programmed depends on the memory technology and the package type. For Read Only Memory (ROM) devices, these bits are specified at time of ROM code submittal and once the device is masked may not be changed for those devices (would require a new mask code). For One Time Programmable (OTP) devices, once these bits are programmed ('0'), they may not be changed. For windowed EPROM devices, once these bits are programmed ('0'), the device must be UV erased to return the configuration word to the erased state. UV erasing the device also erases the program memory. For Flash devices, these bits may be erased and reprogrammed. Note: DS31027A-page 27-2 Microchip does not recommend code protecting windowed devices. 1997 Microchip Technology Inc. Section 27. Device Configuration Bits Section 27.2 is forced to the next page for formatting purposes. 27 Device Configuration Bits 1997 Microchip Technology Inc. DS31027A-page 27-3 PICmicro MID-RANGE MCU FAMILY 27.2 Configuration Word Bits These configuration bits specify some of the modes of the device, and are programmed by a device programmer, or by using the In-Circuit Serial Programming (ICSP) feature of the midrange devices. The device is not able to read the values of these bits, and there placement is automatically taken care of when you select the device in you device programmer. For additional information, please refer to the Programming Specification of the Device. Note 1: Always ensure that your device programmer has the same device selected as you are programming. Note 2: Microchip recommends that the desired configuration bit states be embedded in to the application source code. This is easily done in the MPASM assembler by the use of the CONFIG directive. See Subsection 27.2.1 "MPASM's CONFIG Directive." CP1:CP0: Code Protection bits 11 = Code protection off 10 = See device data sheet 01 = See device data sheet 00 = All memory is code protected Note: Some devices may use more or less bits to determine the code protect. Presently there are also some devices that use only one bit (CP0). For these devices the bit description is: 1 = Code protection off 0 = Code protection on DP: Data EEPROM Memory Code Protection bit 1 = Code protection off 0 = Data EEPROM Memory is code protected Note: This bit is used when a device with ROM program memory also has Data EEPROM memory. BODEN: Brown-out Reset Enable bit 1 = BOR enabled 0 = BOR disabled Note: Enabling Brown-out Reset automatically enables the Power-up Timer (PWRT) regardless of the value of bit PWRTE. Ensure the Power-up Timer is enabled anytime Brown-out Reset is enabled. PWRTE: Power-up Timer Enable bit 1 = PWRT disabled 0 = PWRT enabled Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT) regardless of the value of bit PWRTE. Ensure the Power-up Timer is enabled anytime Brown-out Reset is enabled. Note 2: Some original PICmicros have the polarity of this bit reversed. Note 3: MCLRE: MCLR Pin Function Select bit 1 = Pin's function is MCLR 0 = Pin's function is as a digital I/O. MCLR is internally tied to VDD. WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled DS31027A-page 27-4 1997 Microchip Technology Inc. Section 27. Device Configuration Bits FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator FOSC2:FOSC0: Oscillator Selection bits 111 = EXTRC oscillator, with CLKOUT 110 = EXTRC oscillator 101 = INTRC oscillator, with CLKOUT 100 = INTRC oscillator 011 = Reserved 010 = HS oscillator 001 = XT oscillator 000 = LP oscillator 27 Legend R = Readable bit - n = Value at POR reset Note: 1997 Microchip Technology Inc. P = Programmable bit U = Unimplemented bit, read as `0' u = Unchanged from programmed state The bit position of the configuration bits is device dependent. Please refer to the device programming specification for bit placement. The use of a Microchip device programmer does not require you to know the bit locations. DS31027A-page 27-5 Device Configuration Bits Unimplemented: Read as '1' PICmicro MID-RANGE MCU FAMILY 27.2.1 MPASM's CONFIG Directive Microchip's assembler, MPASM, has a nice feature that allows you to specify, in the source code file, the selected states of the configuration bits for this program. This ensures that when programming a device for an application the required configuration is also programmed. This minimizes the risk of programming the wrong device configuration, and wondering why it no longer works in the application. Example 27-1 show a template for using the CONFIG directive. Example 27-1:Using the CONFIG Directive, a Source File Template ; ; LIST p = p16C77 Revision History ; List Directive, #INCLUDE ; Microchip Device Header File #INCLUDE #INCLUDE ; File which includes my standard macros ; File which includes macros specific ; to this application ; ; ; Specify Device Configuration Bits ; __CONFIG _XT_OSC & _PWRTE_ON & _BODEN_OFF & _CP_OFF & _WDT_ON ; org 0x00 ; Start of Program Memory RESET_ADDR : ; First instruction to execute after a reset end The Symbols that are currently in the Microchip Device Header files that make using the CONFIG directive straight forward are shown in Table 27-1. For the symbols available for your device, please refer to that device's Microchip Include file. Note: DS31027A-page 27-6 As long as the correct device is specified (in the LIST and INCLUDE file directives), the correct polarity of all bits is ensured. 1997 Microchip Technology Inc. Section 27. Device Configuration Bits Table 27-1: __CONFIG Directive Symbols (From Microchip Header Files) Feature SYMBOLS 1997 Microchip Technology Inc. DS31027A-page 27-7 27 Device Configuration Bits _RC_OSC _EXTRC_OSC _EXTRC_OSC_CLKOUT _EXTRC_OSC_NOCLKOUT _INTRC_OSC Oscillators _INTRC_OSC_CLKOUT _INTRC_OSC_NOCLKOUT _LP_OSC _XT_OSC _HS_OSC _WDT_ON Watch Dog Timer _WDT_OFF _PWRTE_ON Power-up Timer _PWRTE_OFF _BODEN_ON Brown-out Reset _BODEN_OFF _MCLRE_ON Master Clear Enable _MCLRE_OFF _CP_ALL _CP_ON Code Protect _CP_75 _CP_50 _CP_OFF _DP_ON Code Protect Data EEPROM _DP_OFF _CPC_ON Code Protect Calibration Space _CPC_OFF Note 1: Not all configuration bit symbols may be available on any one device. Please refer to the MIcrochip include file of that device for available symbols. PICmicro MID-RANGE MCU FAMILY 27.3 Program Verification/Code Protection If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes. Note: 27.3.1 Microchip does not recommend code protecting windowed devices. ROM Devices When a ROM device also has Data EEPROM memory, an additional code protect configuration bit may be implemented. The program memory configuration bit is submitted as part of the ROM code submittal. The Data EEPROM memory code protect configuration bit will be an EEPROM bit. When ROM devices complete testing, the EEPROM data memory code protect bit will be programmed to the same state as the program memory code protect bit. That is data EEPROM code protect is off, when program memory code protect is off, and data EEPROM code protect is on for all other selections. In applications where the device is code protected and the data EEPROM needs to be programmed before the application can be released, the data EEPROM memory must have the entire data EEPROM memory erased. The device programming specification details the steps to do this. Microchip device programmers implement the specified sequence. Once this sequence is complete, the Data EEPROM memory code protect is disabled. This allows the desired data to be programmed into the device. After programming the data EEPROM memory array, the data EEPROM memory code protect configuration bit should be programmed as desired. DS31027A-page 27-8 1997 Microchip Technology Inc. Section 27. Device Configuration Bits 27.4 ID Locations Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code-identification numbers. These locations are not accessible during normal execution but are readable and writable during program/verify. It is recommended that only the 4 least significant bits of the ID location are used. 27 Device Configuration Bits 1997 Microchip Technology Inc. DS31027A-page 27-9 PICmicro MID-RANGE MCU FAMILY 27.5 Design Tips Question 1: I have a JW device and I can no longer program it (reads scrambled data or all '0's). What's wrong with the device? Answer 1: Nothing. You probably code protected the device. If this is the case, the device is no longer usable. See Subsection 27.3 "Program Verification/Code Protection" for more details. Question 2: In converting from a PIC16C74 to a PIC16C74A, my application no longer works. Answer 2: 1. 2. Did you re-assemble the source file specifying the PIC16C74A in the INCLUDE file and LIST directives. The use of the CONFIG directive is highly recommended. On the device programmer, did you specify the PIC16C74A, and were all the configuration bits as desired? Question 3: When I erase the device, the program memory is blank but the configuration word is not yet erased. Answer 3: That is by design. Also remember that Microchip does not recommend code protecting windowed devices. DS31027A-page 27-10 1997 Microchip Technology Inc. Section 27. Device Configuration Bits 27.6 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Configuration Word are: Title Application Note # No related Application Notes at this time. 27 Device Configuration Bits 1997 Microchip Technology Inc. DS31027A-page 27-11 PICmicro MID-RANGE MCU FAMILY 27.7 Revision History Revision A This is the initial released revision of the Configuration Word description. DS31027A-page 27-12 1997 Microchip Technology Inc. M Section 28. In-Circuit Serial ProgrammingTM (ICSPTM) HIGHLIGHTS This section of the manual contains the following major topics: 28.1 Introduction ..................................................................................................................28-2 28.2 Entering In-Circuit Serial Programming Mode .............................................................28-3 28.3 Application Circuit ........................................................................................................28-4 28.4 Programmer .................................................................................................................28-6 28.5 Programming Environment ..........................................................................................28-6 28.6 Other Benefits ..............................................................................................................28-7 28.7 Field Programming of PICmicro OTP MCUs................................................................28-8 28.8 Field Programming of FLASH PICmicros...................................................................28-10 28.9 Design Tips ................................................................................................................28-12 28.10 Related Application Notes..........................................................................................28-13 28.11 Revision History .........................................................................................................28-14 28 ICSP 1997 Microchip Technology Inc. DS31028A page 28-1 PICmicro MID-RANGE MCU FAMILY 28.1 Introduction All midrange devices can be In-Circuit Serial Programmed (ICSPTM) while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground, and the programming voltage. In-Circuit Serial Programming (ICSPTM) is a great way to reduce your inventory overhead and time-to-market for your product. By assembling your product with a blank Microchip microcontroller (MCU), you can stock one design. When an order has been placed, these units can be programmed with the latest revision of firmware, tested, and shipped in a very short time. This method also reduces scrapped inventory due to old firmware revisions. This type of manufacturing system can also facilitate quick turnarounds on custom orders for your product. Most people would think to use ICSP with PICmicroTM OTP MCUs only on an assembly line where the device is programmed once. However, there is a method by which an OTP device can be programmed several times depending on the size of the firmware. This method, explained later, provides a way to field upgrade your firmware in a way similar to EEPROM- or Flash-based devices. DS31028A-page 28-2 1997 Microchip Technology Inc. Section 28. ICSP 28.2 Entering In-Circuit Serial Programming Mode The device is placed into a program/verify mode by holding the RB6 and RB7 pins low while raising the MCLR (VPP) pin from VIL to VIHH (see programming specification) and having VDD at the programming voltage. RB6 becomes the programming clock and RB7 becomes the programming data. Both RB6 and RB7 are Schmitt Trigger inputs in this mode, and when RB7 is driving data it is a CMOS output driver. After reset, to place the device into programming/verify mode, the program counter (PC) is at location 00h. A 6-bit command is then supplied to the device. Some commands then specify that 14-bits of program data are then supplied to or read from the device, depending on if the command was a load or a read. For complete details of serial programming, please refer to the device specific Programming Specifications. During the In-Circuit Serial Programming Mode, the WDT circuitry is disabled from generating a device reset. 28 ICSP 1997 Microchip Technology Inc. DS31028A-page 28-3 PICmicro MID-RANGE MCU FAMILY 28.3 Application Circuit The application circuit must be designed to allow all the programming signals to be directly connected to the PICmicro MCU. Figure 28-1 shows a typical circuit that is a starting point for when designing with ICSP. The application must compensate for the following issues: * * * * * * Isolation of the MCLR/VPP pin from the rest of the circuit Loading of pins RB6 and RB7 Capacitance on each of the VDD, MCLR/VPP, RB6, and RB7 pins Minimum and maximum operating voltage for VDD PICmicro Oscillator Interface to the programmer The MCLR/VPP pin is normally connected to an RC circuit. The pull-up resistor is tied to VDD and a capacitor is tied to ground. This circuit can affect the operation of ICSP depending on the size of the capacitor since the VPP voltage must be isolated from the rest of the circuit (in most cases a resistor is not capable of isolating the circuit). It is, therefore, recommended that the circuit in Figure 28-1 be used when an RC is connected to MCLR/VPP. The diode should be a Schottky-type device. Another issue with MCLR/VPP is that when the PICmicro device is programmed, this pin is driven to approximately 13V and also to ground. Therefore, the application circuit must be isolated from this voltage provided by the programmer. Pins RB6 and RB7 are used by the PICmicro for serial programming. RB6 is the clock line and RB7 is the data line. RB6 is driven by the programmer. RB7 is a bi-directional pin that is driven by the programmer when programming, and driven by the PICmicro when verifying. These pins must be isolated from the rest of the application circuit so as not to affect the signals during programming. You must take into consideration the output impedance of the programmer when isolating RB6 and RB7 from the rest of the circuit. This isolation circuit must account for RB6 being an input on the PICmicro, and for RB7 being bi-directional (can be driven by both the PICmicro and the programmer). For instance, PRO MATE(R) II has an output impedance of 1k. If the design permits, these pins should not be used by the application. This is not the case with most applications so it is recommended that the designer evaluate whether these signals need to be buffered. As a designer, you must consider what type of circuitry is connected to RB6 and RB7 and then make a decision on how to isolate these pins. Figure 28-1 does not show any circuitry to isolate RB6 and RB7 on the application circuit because this is very application dependent. To simplify this interface the optimal usage of these I/O in the application are (in order): 1. 2. 3. Do not use RB6/RB7 so they are dedicated to ICSP. Use these pins as outputs with minimal loading on signal line. Isolation circuitry so that these signals can be driven to the ICSP specifications. Figure 28-1: Typical In-Circuit Serial Programming (ICSP) Application Circuit Application PCB PIC16CXXX VDD VDD MCLR/VPP ICSP Connector VDD VSS RB7 RB6 To application circuit Isolation circuits DS31028A-page 28-4 1997 Microchip Technology Inc. Section 28. ICSP The total capacitance on the programming pins affects the rise rates of these signals as they are driven out of the programmer. Typical circuits use several hundred microfarads of capacitance on VDD which helps to dampen noise and ripple. However, this capacitance requires a fairly strong driver in the programmer to meet the rise rate timings for VDD. Most programmers are designed to simply program the PICmicro itself and don't have strong enough drivers to power the application circuit. One solution is to use a driver board between the programmer and the application circuit. The driver board requires a separate power supply that is capable of driving the VPP and VDD pins with the correct rise rates and should also provide enough current to power the application circuit. RB6 and RB7 are not buffered on this schematic but may require buffering depending upon the application. A sample driver board schematic is shown in Figure 28-2. Note: The driver board design MUST be tested in the user's application to determine the effects of the application circuit on the programming signals timing. Changes may be required if the application places a significant load on VDD, VPP, RB6 OR RB7. The Microchip programming specification states that the device should be programmed at 5V. Special considerations must be made if your application circuit operates at 3V only. These considerations may include totally isolating the PICmicro during programming. The other issue is that the device must be verified at the minimum and maximum voltages at which the application circuit will be operating. For instance, a battery operated system may operate from three 1.5V cells giving an operating voltage range of 2.7V to 4.5V. The programmer must program the device at 5V and must verify the program memory contents at both 2.7V and 4.5V to ensure that proper programming margins have been achieved. This ensures the PICmicro operation over the voltage range of the system. Now all that is left is how to connect the application circuit to the programmer. This depends a lot on the programming environment and will be discussed in that section. 1997 Microchip Technology Inc. DS31028A-page 28-5 28 ICSP The final issue deals with the oscillator circuit on the application board. The voltage on MCLR/VPP must rise to the specified program mode entry voltage before the device executes any code. The crystal modes available on the PICmicro are not affected by this issue because the Oscillator Start-up Timer waits for 1024 oscillations before any code is executed. However, RC oscillators do not require any start-up time and, therefore, the Oscillator Start-up Timer is not used. The programmer must drive MCLR/VPP to the program mode entry voltage before the RC oscillator toggles four times. If the RC oscillator toggles four or more times, the program counter will be incremented to some value X. Now when the device enters programming mode, the program counter will not be zero and the programmer will start programming your code at an offset of X. There are several alternatives that can compensate for a slow rise rate on MCLR/VPP. The first method would be to not populate the R, program the device, and then insert the R. The other method would be to have the programming interface drive the OSC1 pin of the PICmicro to ground while programming. This will prevent any oscillations from occurring during programming. PICmicro MID-RANGE MCU FAMILY 28.4 Programmer The second consideration is the programmer. PIC16CXXX MCUs only use serial programming and therefore all programmers supporting these devices will support ICSP. One issue with the programmer is the drive capability. As discussed before, it must be able to provide the specified rise rates on the ICSP signals and also provide enough current to power the application circuit. Figure 28-2 shows an example driver board. This driver schematic does not show any buffer circuitry for RB6 and RB7. It is recommended that an evaluation be performed to determine if buffering is required. Another issue with the programmer is what VDD levels are used to verify the memory contents of the PICmicro. For instance, the PRO MATE II verifies program memory at the minimum and maximum VDD levels for the specified device and is therefore considered a production quality programmer. On the other hand, the PICSTART(R) Plus only verifies at 5V and is for prototyping use only. The Microchip programming specifications state that the program memory contents should be verified at both the minimum and maximum VDD levels that the application circuit will be operating. This implies that the application circuit must be able to handle the varying VDD voltages. There are also several third party programmers that are available. You should select a programmer based on the features it has and how it fits into your programming environment. The Microchip Development Systems Ordering Guide (DS30177) provides detailed information on all our development tools. The Microchip Third Party Guide (DS00104) provides information on all of our third party tool developers. Please consult these two references when selecting a programmer. Many options exist including serial or parallel PC host connection, stand-alone operation, and single or gang programmers. Some of the third party developers include Advanced Transdata Corporation, BP Microsystems, Data I/O, Emulation Technology and Logical Devices. 28.5 Programming Environment The programming environment will affect the type of programmer used, the programmer cable length, and the application circuit interface. Some programmers are well suited for a manual assembly line while others are desirable for an automated assembly line. You may want to choose a gang programmer to program multiple systems at a time. The physical distance between the programmer and the application circuit affects the load capacitance on each of the programming signals. This will directly affect the drive strength needed to provide the correct signal rise rates and current. This programming cable must also be as short as possible and properly terminated and shielded, or the programming signals may be corrupted by ringing or noise. Finally, the application circuit interface to the programmer depends on the size constraints of the application circuit itself and the assembly line. A simple header can be used to interface the application circuit to the programmer. This might be more desirable for a manual assembly line where a technician plugs the programmer cable into the board. A different method is the use of spring loaded test pins (commonly referred to as pogo pins). The application circuit has pads on the board for each of the programming signals. Then there is a fixture that has pogo pins in the same configuration as the pads on the board. The application circuit or fixture is moved into position such that the pogo pins come into contact with the board. This method might be more suitable for an automated assembly line. After taking into consideration the issues with the application circuit, the programmer, and the programming environment, anyone can build a high quality, reliable manufacturing line based on ICSP. DS31028A-page 28-6 1997 Microchip Technology Inc. Section 28. ICSP 28.6 Other Benefits ICSP provides other benefits, such as calibration and serialization. If program memory permits, it would be cheaper and more reliable to store calibration constants in program memory instead of using an external serial EEPROM. For example, if your system has a thermistor which can vary from one system to another, storing some calibration information in a table format allows the microcontroller to compensate (in software) for external component tolerances. System cost can be reduced without affecting the required performance of the system by using software calibration techniques. But how does this relate to ICSP? The PICmicro has already been programmed with firmware that performs a calibration cycle. The calibration data is transferred to a calibration fixture. When all calibration data has been transferred, the fixture places the PICmicro in programming mode and programs the PICmicro with the calibration data. Application note AN656, In-Circuit Serial Programming of Calibration Parameters Using a PICmicro Microcontroller, shows exactly how to implement this type of calibration data programming. The other benefit of ICSP is serialization. Each individual system can be programmed with a unique or random serial number. One such application of a unique serial number would be for security systems. A typical system might use DIP switches to set the serial number. Instead, this number can be burned into program memory, thus reducing the overall system cost and lowering the risk of tampering. 28 ICSP 1997 Microchip Technology Inc. DS31028A-page 28-7 PICmicro MID-RANGE MCU FAMILY 28.7 Field Programming of PICmicro OTP MCUs An OTP device is not normally capable of being reprogrammed, but the PICmicro architecture gives you this flexibility provided the size of your firmware is at least half that of the desired device and the device is not code protected. If your target device does not have enough program memory, Microchip provides a wide spectrum of devices from 0.5K to 8K program memory with the same set of peripheral features that will help meet the criteria. The PIC16CXXX microcontrollers have two vectors, reset and interrupt, at locations 0x0000 and 0x0004. When the PICmicro encounters a reset or interrupt condition, the code located at one of these two locations in program memory is executed. The first listing of Example 28-2 shows the code that is first programmed into the PICmicro. The second listing of Example 28-2 shows the code that is programmed into the PICmicro for the second time. Example 28-2 shows that to program the PICmicro a second time the memory location 0x0000, originally goto Main (0x2808), is reprogrammed to all 0's which happens to be a NOP instruction. This location cannot be reprogrammed to the new opcode (0x2860) because the bits that are 0's cannot be reprogrammed to 1's, only bits that are 1's can be reprogrammed to 0's. The next memory location 0x0001 was originally blank (all 1's) and now becomes a goto Main (0x2860). When a reset condition occurs, the PICmicro executes the instruction at location 0x0000 which is the NOP, a completely benign instruction, and then executes the goto Main to start the execution of code. The example also shows that all program memory locations after 0x005A are blank in the original program so that the second time the PICmicro is programmed, the revised code can be programmed at these locations. The same descriptions can be given for the interrupt vector at location 0x0004. This method changes slightly for PICmicros with >2K words of program memory. Each of the goto Main and goto ISR instructions are replaced by the following code segment is Example 28-1 due to paging on devices with >2K words of program memory. Example 28-1: Crossing Program Memory Pages movlw movwf PCLATH goto Main movlw movwf PCLATH goto ISR Now your one-time programmable PICmicro is exhibiting EEPROM- or Flash-like qualities. DS31028A-page 28-8 1997 Microchip Technology Inc. Section 28. ICSP Example 28-2: Programming Cycle Listing Files 1997 Microchip Technology Inc. DS31028A-page 28-9 28 ICSP First Program Cycle Second Program Cycle _________________________________________________________________________________________ Prog Opcode Assembly | Prog Opcode Assembly Mem Instruction | Mem Instruction ----------------------------------------------------------------------------------------0000 2808 goto Main ;Main loop | 0000 0000 nop 0001 3FFF ; at 0x0008 | 0001 2860 goto Main; Main now 0002 3FFF | 0002 3FFF ; at 0x0060 0003 3FFF | 0003 3FFF 0004 2848 goto ISR ; ISR at | 0004 0000 nop 0005 3FFF ; 0x0048 | 0005 28A8 goto ISR ; ISR now at 0006 3FFF | 0006 3FFF ; 0x00A8 0007 3FFF | 0007 3FFF 0008 1683 bsf STATUS,RP0 | 0008 1683 bsf STATUS,RP0 0009 3007 movlw 0x07 | 0009 3007 movlw 0x07 000A 009F movwf ADCON1 | 000A 009F movwf ADCON1 . | . . | . . | . 0048 1C0C btfss PIR1,RBIF | 0048 1C0C btfss PIR1,RBIF 0049 284E goto EndISR | 0049 284E goto EndISR 004A 1806 btfsc PORTB,0 | 004A 1806 btfsc PORTB,0 . | . . | . . | . 0060 3FFF | 0060 1683 bsf STATUS,RP0 0061 3FFF | 0061 3005 movlw 0x05 0062 3FFF | 0062 009F movwf ADCON1 . | . . | . . | . 00A8 3FFF | 00A8 1C0C btfss PIR1,RBIF 00A9 3FFF | 00A9 28AE goto EndISR 00AA 3FFF | 00AA 1806 btfsc PORTB,0 . | . . | . . | . ----------------------------------------------------------------------------------------- PICmicro MID-RANGE MCU FAMILY 28.8 Field Programming of FLASH PICmicros With the ICSP interface circuitry already in place, FLASH-based PICmicros can be easily reprogrammed in the field. These FLASH devices allow you to reprogram them even if they are code protected. A portable ICSP programming station might consist of a laptop computer and programmer. The technician plugs the ICSP interface cable into the application circuit and downloads the new firmware into the PICmicro. The next thing you know the system is up and running without those annoying "bugs." Another instance would be that you want to add an additional feature to your system. All of your current inventory can be converted to the new firmware and field upgrades can be performed to bring your installed base of systems up to the latest revision of firmware. DS31028A-page 28-10 1997 Microchip Technology Inc. 1997 Microchip Technology Inc. VPP VDD 5 6 3 2 HEADER JP2 1 2 HEADER JP1 1 2 3 4 5 +15V 4 11 +15V VPP VDD RB7 RB6 TLE2144A 7 U1B 0.1 C3 TLE2144A 1 100 R10 100 R5 +15V C8 0.001 10 9 C7 0.001 12 13 14 8 C5 0.1 1 3 GND VR1 LM7808 VIN TLE2144A U1C TLE2144A U1D VOUT 100 R9 100 R6 2 2 R8 100 2 2 C9 100 R2 5.1k 1 Q4 2N2222 3 +15V 1 Q2 2N2907 3 R1 5.1k 1 Q3 2N2222 3 +8V C4 0.1 +8V 1 R4 1 9 5 2 7 14 PVDD 12 PVPP PVDD RB7 PRB6 RB6 0.1 C6 Note: All resistors are in Ohms, all capacitors are in F. PVPP PVDD PRB6 JP3 1 2 3 4 5 11 U2D 74HC126 8 U2C 74HC126 6 U2B 74HC126 3 U2A 74HC126 HEADER 13 10 4 1 Figure 28-2: ICSP U1A R7 100 2 1 Q1 2N2907 3 R3 Section 28. ICSP Example Driver Board Schematic 28 DS31028A-page 28-11 PICmicro MID-RANGE MCU FAMILY 28.9 Design Tips Question 1: When I try to do ICSP, the entire program is shifted (offset) in the device program memory. Answer 1: If the MCLR pin does not rise fast enough, while the device's voltage is in the valid operating range, the internal Program Counter (PC) can increment. This means that the PC is no longer pointing to the address that you expected to be at. The exact location depends on the number of device clocks that occurred in the valid operating region of the device. Question 2: I am using a PRO MATE II with a socket that I designed to bring the programming signal to my application board. Sometimes when I try to do ICSP, the program memory is programmed wrong. Answer 2: The voltages / timings may be violated at the device. This could be due to the: * Application board circuitry * Cable length from programmer to target * Large capacitance on VDD which affects levels / timings DS31028A-page 28-12 1997 Microchip Technology Inc. Section 28. ICSP 28.10 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to In-Circuit Serial Programming are: Title In-Circuit Serial Programming of Calibration Parameters using a PICmicro In-Circuit Serial Programming Guide Application Note # AN656 DS30277 28 ICSP 1997 Microchip Technology Inc. DS31028A-page 28-13 PICmicro MID-RANGE MCU FAMILY 28.11 Revision History Revision A This is the initial released revision of the In-Circuit Serial Programming description. DS31028A-page 28-14 1997 Microchip Technology Inc. M Section 29. Instruction Set HIGHLIGHTS This section of the manual contains the following major topics: 29.1 29.2 29.3 29.4 29.5 29.6 29.7 29.8 Introduction ..................................................................................................................29-2 Instruction Formats ......................................................................................................29-4 Special Function Registers as Source/Destination ......................................................29-6 Q Cycle Activity............................................................................................................29-7 Instruction Descriptions................................................................................................29-8 Design Tips ................................................................................................................29-45 Related Application Notes..........................................................................................29-47 Revision History .........................................................................................................29-48 29 Instruction Set 1997 Microchip Technology Inc. DS31029A page 29-1 PICmicro MID-RANGE MCU FAMILY 29.1 Introduction Each midrange instruction is a 14-bit word divided into an OPCODE which specifies the instruction type and one or more operands which further specify the operation of the instruction. The midrange Instruction Set Summary in Table 29-1 lists the instructions recognized by the MPASM assembler. The instruction set is highly orthogonal and is grouped into three basic categories: * Byte-oriented operations * Bit-oriented operations * Literal and control operations Table 29-2 gives the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the number of the file in which the bit is located. For literal and control operations, 'k' represents an eight or eleven bit constant or literal value. All instructions are executed in one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In these cases, the execution takes two instruction cycles with the second cycle executed as an NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. DS31029A-page 29-2 1997 Microchip Technology Inc. Section 29. Instruction Set Table 29-1: Midrange Instruction Set Mnemonic, Operands 14-Bit Instruction Word Description Cycles MSb LSb Status Affected Notes 1997 Microchip Technology Inc. DS31029A-page 29-3 29 Instruction Set BYTE-ORIENTED FILE REGISTER OPERATIONS 1,2 00 0111 dfff ffff C,DC,Z 1 f, d Add W and f ADDWF 1,2 00 0101 dfff ffff Z 1 f, d AND W with f ANDWF 2 00 0001 lfff ffff Z 1 Clear f f CLRF 00 0001 0xxx xxxx Z 1 Clear W CLRW 1,2 00 1001 dfff ffff Z 1 f, d Complement f COMF 1,2 00 0011 dfff ffff Z 1 f, d Decrement f DECF 1,2,3 00 1011 dfff ffff 1(2) f, d Decrement f, Skip if 0 DECFSZ 1,2 00 1010 dfff ffff Z 1 f, d Increment f INCF 1,2,3 00 1111 dfff ffff 1(2) f, d Increment f, Skip if 0 INCFSZ 1,2 00 0100 dfff ffff Z 1 f, d Inclusive OR W with f IORWF 1,2 00 1000 dfff ffff Z 1 f, d Move f MOVF 00 0000 lfff ffff 1 Move W to f f MOVWF 00 0000 0xx0 0000 1 No Operation NOP 1,2 00 1101 dfff ffff C 1 f, d Rotate Left f through Carry RLF 1,2 00 1100 dfff ffff C 1 f, d Rotate Right f through Carry RRF 1,2 00 0010 dfff ffff C,DC,Z 1 f, d Subtract W from f SUBWF 1,2 00 1110 dfff ffff 1 f, d Swap nibbles in f SWAPF 1,2 00 0110 dfff ffff Z 1 f, d Exclusive OR W with f XORWF BIT-ORIENTED FILE REGISTER OPERATIONS 1,2 01 00bb bfff ffff 1 f, b Bit Clear f BCF 1,2 01 01bb bfff ffff 1 f, b Bit Set f BSF 3 01 10bb bfff ffff 1 (2) f, b Bit Test f, Skip if Clear BTFSC 3 01 11bb bfff ffff 1 (2) f, b Bit Test f, Skip if Set BTFSS LITERAL AND CONTROL OPERATIONS 11 111x kkkk kkkk C,DC,Z 1 Add literal and W k ADDLW 11 1001 kkkk kkkk Z 1 AND literal with W k ANDLW 10 0kkk kkkk kkkk 2 Call subroutine k CALL 00 0000 0110 0100 TO,PD 1 Clear Watchdog Timer CLRWDT 10 1kkk kkkk kkkk 2 Go to address k GOTO 11 1000 kkkk kkkk Z 1 Inclusive OR literal with W k IORLW 11 00xx kkkk kkkk 1 Move literal to W k MOVLW 00 0000 0000 1001 2 Return from interrupt RETFIE 11 01xx kkkk kkkk 2 Return with literal in W k RETLW 00 0000 0000 1000 2 Return from Subroutine RETURN 00 0000 0110 0011 TO,PD 1 Go into standby mode SLEEP 11 110x kkkk kkkk C,DC,Z 1 Subtract W from literal k SUBLW 11 1010 kkkk kkkk Z 1 Exclusive OR literal with W k XORLW Note 1: When an I/O register is modified as a function of itself (e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. PICmicro MID-RANGE MCU FAMILY 29.2 Instruction Formats Figure 29-1 shows the three general formats that the instructions can have. As can be seen from the general format of the instructions, the opcode portion of the instruction word varies from 3-bits to 6-bits of information. This is what allows the midrange instruction set to have 35 instructions. Note 1: Any unused opcode is Reserved. Use of any reserved opcode may cause unexpected operation. Note 2: To maintain upward compatibility with future midrange products, do not use the OPTION and TRIS instructions. All instruction examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit. To represent a binary number: 00000100b where b is a binary string identifier. Figure 29-1: General Format for Instructions Byte-oriented file register operations 13 8 OPCODE 7 d 6 0 f (FILE #) d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) 0 f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 8 7 OPCODE 0 k (literal) k = 8-bit literal (immediate) value CALL and GOTO instructions only 13 11 OPCODE 10 0 k (literal) k = 11-bit literal (immediate) value DS31029A-page 29-4 1997 Microchip Technology Inc. Section 29. Instruction Set Table 29-2: Instruction Description Conventions Field Description Register file address (0x00 to 0x7F) Working register (accumulator) Bit address within an 8-bit file register (0 to 7) Literal field, constant data or label (may be either an 8-bit or an 11-bit value) Don't care (0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d Destination select; d = 0: store result in W, d = 1: store result in file register f. dest Destination either the W register or the specified register file location label Label name TOS Top of Stack PC Program Counter PCLATH Program Counter High Latch GIE Global Interrupt Enable bit WDT Watchdog Timer TO Time-out bit PD Power-down bit [ ] Optional ( ) Contents Assigned to <> Register bit field In the set of italics User defined term (font is courier) f W b k x 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-5 PICmicro MID-RANGE MCU FAMILY 29.3 Special Function Registers as Source/Destination The Section 29. Instruction Set's orthogonal instruction set allows read and write of all file registers, including special function registers. Some special situations the user should be aware of are explained in the following subsections: 29.3.1 STATUS Register as Destination If an instruction writes to the STATUS register, the Z, C, DC and OV bits may be set or cleared as a result of the instruction and overwrite the original data bits written. For example, executing CLRF STATUS will clear register STATUS, and then set the Z bit leaving 0000 0100b in the register. 29.3.2 PCL as Source or Destination Read, write or read-modify-write on PCL may have the following results: Read PC: PCL dest; Write PCL: PCLATH PCH; 8-bit destination value PCL Read-Modify-Write: PCL ALU operand PCLATH PCH; 8-bit result PCL PCLATH does not change; Where PCH = program counter high byte (not an addressable register), PCLATH = Program counter high holding latch, dest = destination, W register or register file f. 29.3.3 Bit Manipulation All bit manipulation instructions will first read the entire register, operate on the selected bit and then write the result back (read-modify-write (R-M-W)) the specified register. The user should keep this in mind when operating on some special function registers, such as ports. Note: DS31029A-page 29-6 Status bits that are manipulated by the device (including the interrupt flag bits) are set or cleared in the Q1 cycle. So there is no issue with executing R-M-W instructions on registers which contain these bits. 1997 Microchip Technology Inc. Section 29. Instruction Set 29.4 Q Cycle Activity Each instruction cycle (Tcy) is comprised of four Q cycles (Q1-Q4). The Q cycle is the same as the device oscillator cycle (TOSC). The Q cycles provide the timing/designation for the Decode, Read, Process Data, Write etc., of each instruction cycle. The following diagram shows the relationship of the Q cycles to the instruction cycle. The four Q cycles that make up an instruction cycle (Tcy) can be generalized as: Q1: Instruction Decode Cycle or forced No Operation Q2: Instruction Read Cycle or No Operation Q3: Process the Data Q4: Instruction Write Cycle or No Operation Each instruction will show the detailed Q cycle operation for the instruction. Figure 29-2: Q Cycle Activity Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Tosc Tcy1 Tcy2 Tcy3 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-7 PICmicro MID-RANGE MCU FAMILY 29.5 Instruction Descriptions ADDLW Add Literal and W Syntax: [ label ] ADDLW Operands: 0 k 255 Operation: (W) + k W Status Affected: C, DC, Z Encoding: 11 111x k kkkk kkkk Description: The contents of the W register are added to the eight bit literal 'k' and the result is placed in the W register. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example1 Q3 Read literal 'k' ADDLW Process data Q4 Write to W register 0x15 Before Instruction W = 0x10 After Instruction W Example 2 ADDLW = 0x25 MYREG Before Instruction W = 0x10 Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W Example 3 ADDLW = 0x47 HIGH (LU_TABLE) Before Instruction W = 0x10 Address of LU_TABLE = 0x9375 LU_TABLE is a label for an address in program memory After Instruction W Example 4 ADDLW = 0xA3 MYREG Before Instruction W = 0x10 Address of PCL = 0x02 PCL is the symbol for the Program Counter low byte location After Instruction W DS31029A-page 29-8 = 0x12 1997 Microchip Technology Inc. Section 29. Instruction Set ADDWF Add W and f Syntax: [ label ] ADDWF Operands: 0 f 127 d [0,1] Operation: (W) + (f) destination Status Affected: C, DC, Z Encoding: 00 f,d 0111 dfff ffff Description: Add the contents of the W register with register 'f'. If 'd' is 0 the result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' ADDWF Q4 Process data Write to destination FSR, 0 Before Instruction W = 0x17 FSR = 0xC2 After Instruction W = 0xD9 FSR = 0xC2 Example 2 ADDWF INDF, 1 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x20 After Instruction 29 W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x37 Case 1: ADDWF Instruction Set Example 3 PCL Before Instruction W = 0x10 PCL = 0x37 C = x After Instruction PCL = 0x47 C = 0 Case 2: Before Instruction W PCL PCH C = = = = 0x10 0xF7 0x08 x After Instruction PCL = 0x07 PCH = 0x08 C = 1 1997 Microchip Technology Inc. DS31029A-page 29-9 PICmicro MID-RANGE MCU FAMILY ANDLW And Literal with W Syntax: [ label ] ANDLW Operands: 0 k 255 Operation: (W).AND. (k) W Status Affected: Z Encoding: 11 1001 k kkkk kkkk Description: The contents of W register are AND'ed with the eight bit literal 'k'. The result is placed in the W register. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read literal 'k' ANDLW Process data Q4 Write to W register 0x5F Before Instruction W = 0xA3 After Instruction W Example 2 ANDLW = 0x03 ; 0101 1111 ; 1010 0011 ;---------; 0000 0011 (0x5F) (0xA3) -----(0x03) MYREG Before Instruction W = 0xA3 Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W Example 3 ANDLW = 0x23 HIGH (LU_TABLE) Before Instruction W = 0xA3 Address of LU_TABLE = 0x9375 LU_TABLE is a label for an address in program memory After Instruction W DS31029A-page 29-10 = 0x83 1997 Microchip Technology Inc. Section 29. Instruction Set ANDWF AND W with f Syntax: [ label ] ANDWF Operands: 0 f 127 d [0,1] Operation: (W).AND. (f) destination Status Affected: Z Encoding: 00 0101 f,d dfff ffff Description: AND the W register with register 'f'. If 'd' is 0 the result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' ANDWF Process data Q4 Write to destination FSR, 1 Before Instruction W = 0x17 FSR = 0xC2 After Instruction ; 0001 0111 ; 1100 0010 ;---------; 0000 0010 (0x17) (0xC2) -----(0x02) ; 0001 0111 ; 1100 0010 ;---------; 0000 0010 (0x17) (0xC2) -----(0x02) W = 0x17 FSR = 0x02 Example 2 ANDWF FSR, 0 Before Instruction W = 0x17 FSR = 0xC2 After Instruction W = 0x02 FSR = 0xC2 ANDWF INDF, 1 Instruction Set Example 3 29 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x5A After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x15 1997 Microchip Technology Inc. DS31029A-page 29-11 PICmicro MID-RANGE MCU FAMILY BCF Bit Clear f Syntax: [ label ] BCF Operands: 0 f 127 0b7 Operation: 0 f Status Affected: None Encoding: 01 f,b 00bb bfff ffff Description: Bit 'b' in register 'f' is cleared. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' BCF Q4 Process data Write register 'f' FLAG_REG, 7 Before Instruction FLAG_REG = 0xC7 ; 1100 0111 After Instruction FLAG_REG = 0x47 Example 2 BCF ; 0100 0111 INDF, 3 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x2F After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x27 DS31029A-page 29-12 1997 Microchip Technology Inc. Section 29. Instruction Set BSF Bit Set f Syntax: [ label ] BSF Operands: 0 f 127 0b7 Operation: 1 f Status Affected: None Encoding: 01 f,b 01bb bfff Description: Bit 'b' in register 'f' is set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' BSF ffff Q4 Process data Write register 'f' FLAG_REG, 7 Before Instruction FLAG_REG =0x0A ; 0000 1010 After Instruction FLAG_REG =0x8A Example 2 BSF ; 1000 1010 INDF, 3 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x20 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x28 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-13 PICmicro MID-RANGE MCU FAMILY BTFSC Bit Test, Skip if Clear Syntax: [ label ] BTFSC f,b Operands: 0 f 127 0b7 Operation: skip if (f) = 0 Status Affected: None Encoding: Description: 01 10bb bfff ffff If bit 'b' in register 'f' is '0' then the next instruction is skipped. If bit 'b' is '0' then the next instruction (fetched during the current instruction execution) is discarded, and a NOP is executed instead, making this a 2 cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: Q1 Q2 Decode Read register 'f' If skip (2nd cycle): Q1 Q2 No operation Example 1 Case 1: No operation HERE FALSE TRUE Q3 Q4 Process data Q3 Q4 No operation BTFSC GOTO * * * No operation No operation FLAG, 4 PROCESS_CODE Before Instruction PC = FLAG= addressHERE xxx0 xxxx After Instruction Since FLAG<4>= 0, PC = addressTRUE Case 2: Before Instruction PC = FLAG= addressHERE xxx1 xxxx After Instruction Since FLAG<4>=1, PC = addressFALSE DS31029A-page 29-14 1997 Microchip Technology Inc. Section 29. Instruction Set BTFSS Bit Test f, Skip if Set Syntax: [ label ] BTFSS f,b Operands: 0 f 127 0b<7 Operation: skip if (f) = 1 Status Affected: None Encoding: 01 11bb bfff ffff Description: If bit 'b' in register 'f' is '1' then the next instruction is skipped. If bit 'b' is '1', then the next instruction (fetched during the current instruction execution) is discarded and a NOP is executed instead, making this a 2 cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: Q1 Q2 Decode Read register 'f' If skip (2nd cycle): Q1 Q2 No operation Example 1 Case 1: No operation HERE FALSE TRUE Q3 Q4 Process data Q3 Q4 No operation BTFSS GOTO * * * No operation No operation FLAG, 4 PROCESS_CODE Before Instruction PC = FLAG= addressHERE xxx0 xxxx After Instruction 29 Since FLAG<4>= 0, PC = addressFALSE Case 2: Before Instruction addressHERE xxx1 xxxx Instruction Set PC = FLAG= After Instruction Since FLAG<4>=1, PC = addressTRUE 1997 Microchip Technology Inc. DS31029A-page 29-15 PICmicro MID-RANGE MCU FAMILY CALL Call Subroutine Syntax: [ label ] CALL k Operands: 0 k 2047 Operation: (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> Status Affected: None Encoding: 10 0kkk kkkk kkkk Description: Call Subroutine. First, the 13-bit return address (PC+1) is pushed onto the stack. The eleven bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH<4:3>. CALL is a two cycle instruction. Words: 1 Cycles: 2 Q Cycle Activity: 1st cycle: Q1 Q2 Decode 2nd cycle: Q1 No operation Example 1 Q3 Read literal 'k' Q2 Q4 Process data Q3 No operation HERE No operation Q4 No operation CALL No operation THERE Before Instruction PC = AddressHERE After Instruction TOS = Address HERE+1 PC = Address THERE DS31029A-page 29-16 1997 Microchip Technology Inc. Section 29. Instruction Set CLRF Clear f Syntax: [ label ] CLRF Operands: 0 f 127 Operation: 00h f 1Z Status Affected: Z Encoding: 00 f 0001 1fff ffff Description: The contents of register 'f' are cleared and the Z bit is set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' CLRF Process data Q4 Write register 'f' FLAG_REG Before Instruction FLAG_REG=0x5A After Instruction FLAG_REG=0x00 Z = 1 Example 2 CLRF INDF Before Instruction FSR = 0xC2 Contents of Address (FSR)=0xAA After Instruction FSR = 0xC2 Contents of Address (FSR)=0x00 Z = 1 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-17 PICmicro MID-RANGE MCU FAMILY CLRW Clear W Syntax: [ label ] CLRW Operands: None Operation: 00h W 1Z Status Affected: Z Encoding: 00 0001 0xxx xxxx Description: W register is cleared. Zero bit (Z) is set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' Q4 Process data Write register 'W' CLRW Before Instruction W = 0x5A After Instruction W Z DS31029A-page 29-18 = = 0x00 1 1997 Microchip Technology Inc. Section 29. Instruction Set CLRWDT Clear Watchdog Timer Syntax: [ label ] CLRWDT Operands: None Operation: 00h WDT 0 WDT prescaler count, 1 TO 1 PD Status Affected: TO, PD Encoding: 00 0000 0110 0100 Description: CLRWDT instruction clears the Watchdog Timer. It also clears the prescaler count of the WDT. Status bits TO and PD are set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 No operation Process data Q4 Clear WDT Counter CLRWDT Before Instruction WDT counter= x WDT prescaler =1:128 After Instruction WDT counter=0x00 WDT prescaler count=0 TO = 1 PD = 1 WDT prescaler =1:128 Note: The CLRWDT instruction does not affect the assignment of the WDT prescaler. 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-19 PICmicro MID-RANGE MCU FAMILY COMF Complement f Syntax: [ label ] COMF Operands: 0 f 127 d [0,1] Operation: (f) destination Status Affected: Z Encoding: 00 f,d 1001 dfff ffff Description: The contents of register 'f' are 1's complemented. If 'd' is 0 the result is stored in W. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' COMF Q4 Process data Write to destination REG1, 0 Before Instruction REG1= 0x13 After Instruction REG1= W = Example 2 COMF 0x13 0xEC INDF, 1 Before Instruction FSR = 0xC2 Contents of Address (FSR)=0xAA After Instruction FSR = 0xC2 Contents of Address (FSR)=0x55 Example 3 COMF REG1, 1 Before Instruction REG1= 0xFF After Instruction REG1= Z = DS31029A-page 29-20 0x00 1 1997 Microchip Technology Inc. Section 29. Instruction Set DECF Decrement f Syntax: [ label ] DECF f,d Operands: 0 f 127 d [0,1] Operation: (f) - 1 destination Status Affected: Z Encoding: 00 0011 dfff ffff Description: Decrement register 'f'. If 'd' is 0 the result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' DECF Process data Q4 Write to destination CNT, 1 Before Instruction CNT = 0x01 Z = 0 After Instruction CNT = 0x00 Z = 1 Example 2 DECF INDF, 1 Before Instruction FSR = 0xC2 Contents of Address (FSR) = 0x01 Z = 0 After Instruction 29 FSR = 0xC2 Contents of Address (FSR) = 0x00 Z = 1 DECF Instruction Set Example 3 CNT, 0 Before Instruction CNT = 0x10 W = x Z = 0 After Instruction CNT = 0x10 W = 0x0F Z = 0 1997 Microchip Technology Inc. DS31029A-page 29-21 PICmicro MID-RANGE MCU FAMILY DECFSZ Decrement f, Skip if 0 Syntax: [ label ] DECFSZ f,d Operands: 0 f 127 d [0,1] Operation: (f) - 1 destination; skip if result = 0 Status Affected: None Encoding: 00 1011 dfff ffff Description: The contents of register 'f' are decremented. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. If the result is 0, then the next instruction (fetched during the current instruction execution) is discarded and a NOP is executed instead, making this a 2 cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: Q1 Q2 Decode Q3 Read register 'f' If skip (2nd cycle): Q1 Q2 No operation Example Case 1: Q4 Process data Q3 No operation Write to destination Q4 No operation HERE DECFSZ GOTO CONTINUE * * * No operation CNT, 1 LOOP Before Instruction PC CNT = = address HERE 0x01 After Instruction CNT PC Case 2: = = 0x00 address CONTINUE Before Instruction PC CNT = = address HERE 0x02 After Instruction CNT PC DS31029A-page 29-22 = = 0x01 address HERE + 1 1997 Microchip Technology Inc. Section 29. Instruction Set GOTO Unconditional Branch Syntax: [ label ] Operands: 0 k 2047 Operation: k PC<10:0> PCLATH<4:3> PC<12:11> Status Affected: None Encoding: 10 GOTO k 1kkk kkkk kkkk Description: GOTO is an unconditional branch. The eleven bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two cycle instruction. Words: 1 Cycles: 2 Q Cycle Activity: 1st cycle: Q1 Q2 Decode 2nd cycle: Q1 No operation Example Q3 Read literal 'k'<7:0> Q2 Process data Q3 No operation No operation Q4 No operation Q4 No operation GOTO THERE After Instruction PC =AddressTHERE 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-23 PICmicro MID-RANGE MCU FAMILY INCF Increment f Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) + 1 destination Status Affected: Z Encoding: 00 INCF f,d 1010 dfff ffff Description: The contents of register 'f' are incremented. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' INCF Q4 Process data Write to destination CNT, 1 Before Instruction CNT = Z = 0xFF 0 After Instruction CNT = Z = Example 2 INCF 0x00 1 INDF, 1 Before Instruction FSR = 0xC2 Contents of Address (FSR) = 0xFF Z = 0 After Instruction FSR = 0xC2 Contents of Address (FSR) = 0x00 Z = 1 Example 3 INCF CNT, 0 Before Instruction CNT = 0x10 W = x Z = 0 After Instruction CNT = 0x10 W = 0x11 Z = 0 DS31029A-page 29-24 1997 Microchip Technology Inc. Section 29. Instruction Set INCFSZ Increment f, Skip if 0 Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) + 1 destination, skip if result = 0 Status Affected: None Encoding: 00 INCFSZ f,d 1111 dfff ffff Description: The contents of register 'f' are incremented. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. If the result is 0, then the next instruction (fetched during the current instruction execution) is discarded and a NOP is executed instead, making this a 2 cycle instruction. Words: 1 Cycles: 1(2) Q Cycle Activity: Q1 Q2 Decode Q3 Read register 'f' If skip (2nd cycle): Q1 Q2 No operation Example Case 1: Q4 Process data Q3 No operation Write to destination Q4 No operation HERE INCFSZ GOTO CONTINUE * * * No operation CNT, 1 LOOP Before Instruction PC CNT = = address HERE 0xFF 29 After Instruction CNT PC 0x00 address CONTINUE Before Instruction PC CNT = = Instruction Set Case 2: = = address HERE 0x00 After Instruction CNT PC 1997 Microchip Technology Inc. = = 0x01 address HERE + 1 DS31029A-page 29-25 PICmicro MID-RANGE MCU FAMILY IORLW Inclusive OR Literal with W Syntax: [ label ] Operands: 0 k 255 Operation: (W).OR. k W Status Affected: Z Encoding: IORLW k 11 1000 kkkk kkkk Description: The contents of the W register is OR'ed with the eight bit literal 'k'. The result is placed in the W register. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read literal 'k' IORLW Process data Q4 Write to W register 0x35 Before Instruction W = 0x9A After Instruction W Z Example 2 IORLW = 0xBF = 0 MYREG Before Instruction W = 0x9A Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W Z Example 3 IORLW = 0x9F = 0 HIGH (LU_TABLE) Before Instruction W = 0x9A Address of LU_TABLE = 0x9375 LU_TABLE is a label for an address in program memory After Instruction W Z Example 4 IORLW = 0x9B = 0 0x00 Before Instruction W = 0x00 After Instruction W Z DS31029A-page 29-26 = 0x00 = 1 1997 Microchip Technology Inc. Section 29. Instruction Set IORWF Inclusive OR W with f Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (W).OR. (f) destination Status Affected: Z Encoding: 00 IORWF 0100 f,d dfff ffff Description: Inclusive OR the W register with register 'f'. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' IORWF Process data Q4 Write to destination RESULT, 0 Before Instruction RESULT=0x13 W = 0x91 After Instruction RESULT=0x13 W = 0x93 Z = 0 Example 2 IORWF INDF, 1 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x30 29 After Instruction Example 3 Case 1: IORWF Instruction Set W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x37 Z = 0 RESULT, 1 Before Instruction RESULT=0x13 W = 0x91 After Instruction RESULT=0x93 W = 0x91 Z = 0 Case 2: Before Instruction RESULT=0x00 W = 0x00 After Instruction RESULT=0x00 W = 0x00 Z = 1 1997 Microchip Technology Inc. DS31029A-page 29-27 PICmicro MID-RANGE MCU FAMILY MOVLW Move Literal to W Syntax: [ label ] Operands: 0 k 255 Operation: kW Status Affected: None Encoding: MOVLW k 11 00xx kkkk kkkk Description: The eight bit literal 'k' is loaded into W register. The don't cares will assemble as 0's. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read literal 'k' MOVLW Q4 Process data Write to W register 0x5A After Instruction W Example 2 MOVLW = 0x5A MYREG Before Instruction W = 0x10 Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W Example 3 MOVLW = 0x37 HIGH (LU_TABLE) Before Instruction W = 0x10 Address of LU_TABLE = 0x9375 LU_TABLE is a label for an address in program memory After Instruction W DS31029A-page 29-28 = 0x93 1997 Microchip Technology Inc. Section 29. Instruction Set MOVF Move f Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) destination Status Affected: Z Encoding: MOVF f,d 00 1000 dfff ffff Description: The contents of register 'f' is moved to a destination dependent upon the status of 'd'. If 'd' = 0, destination is W register. If 'd' = 1, the destination is file register 'f' itself. 'd' = 1 is useful to test a file register since status flag Z is affected. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' MOVF Process data Q4 Write to destination FSR, 0 Before Instruction W = 0x00 FSR = 0xC2 After Instruction W Z Example 2 MOVF = 0xC2 = 0 INDF, 0 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x00 29 After Instruction Example 3 Case 1: MOVF Instruction Set W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x00 Z = 1 FSR, 1 Before Instruction FSR = 0x43 After Instruction FSR = 0x43 Z = 0 Case 2: Before Instruction FSR = 0x00 After Instruction FSR = 0x00 Z = 1 1997 Microchip Technology Inc. DS31029A-page 29-29 PICmicro MID-RANGE MCU FAMILY MOVWF Move W to f Syntax: [ label ] Operands: 0 f 127 Operation: (W) f Status Affected: None Encoding: 00 MOVWF 0000 f 1fff ffff Description: Move data from W register to register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' MOVWF Process data Q4 Write register 'f' OPTION_REG Before Instruction OPTION_REG=0xFF W = 0x4F After Instruction OPTION_REG=0x4F W = 0x4F Example 2 MOVWF INDF Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x00 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x17 DS31029A-page 29-30 1997 Microchip Technology Inc. Section 29. Instruction Set NOP No Operation Syntax: [ label ] Operands: None Operation: No operation Status Affected: None Encoding: 00 NOP 0000 Description: No operation. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example : 0xx0 Q3 No operation HERE 0000 Q4 No operation No operation NOP Before Instruction PC = address HERE After Instruction PC = address HERE + 1 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-31 PICmicro MID-RANGE MCU FAMILY OPTION Load Option Register Syntax: [ label ] Operands: None Operation: (W) OPTION Status Affected: None Encoding: 00 OPTION 0000 0110 0010 Description: The contents of the W register are loaded in the OPTION register. This instruction is supported for code compatibility with PIC16C5X products. Since OPTION is a readable/writable register, the user can directly address it. Words: 1 Cycles: 1 To maintain upward compatibility with future PIC16CXX products, do not use this instruction. DS31029A-page 29-32 1997 Microchip Technology Inc. Section 29. Instruction Set RETFIE Return from Interrupt Syntax: [ label ] Operands: None Operation: TOS PC, 1 GIE Status Affected: None Encoding: 00 RETFIE 0000 0000 1001 Description: Return from Interrupt. The 13-bit address at the Top of Stack (TOS) is loaded in the PC. The Global Interrupt Enable bit, GIE (INTCON<7>), is automatically set, enabling Interrupts. This is a two cycle instruction. Words: 1 Cycles: 2 Q Cycle Activity: 1st cycle: Q1 Q2 Decode 2nd cycle: Q1 No operation Example Q3 No operation Q2 Process data Q3 No operation No operation Q4 No operation Q4 No operation RETFIE After Instruction PC = TOS GIE = 1 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-33 PICmicro MID-RANGE MCU FAMILY RETLW Return with Literal in W Syntax: [ label ] Operands: 0 k 255 Operation: k W; TOS PC Status Affected: None Encoding: RETLW k 11 01xx kkkk kkkk Description: The W register is loaded with the eight bit literal 'k'. The program counter is loaded 13-bit address at the Top of Stack (the return address). This is a two cycle instruction. Words: 1 Cycles: 2 Q Cycle Activity: 1st cycle: Q1 Q2 Decode 2nd cycle: Q1 No operation Example Q3 Read literal 'k' Q2 Q3 No operation HERE TABLE Q4 Process data Q4 No operation CALL TABLE * * * ADDWF RETLW RETLW * * * RETLW Write to W register No operation ; W contains table ; offset value ; W now has table value PC k1 k2 ;W = offset ;Begin table ; kn ; End of table Before Instruction W = 0x07 After Instruction W = value of k8 PC = TOS = Address Here + 1 DS31029A-page 29-34 1997 Microchip Technology Inc. Section 29. Instruction Set RETURN Return from Subroutine Syntax: [ label ] Operands: None Operation: TOS PC Status Affected: None Encoding: 00 RETURN 0000 0000 1000 Description: Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two cycle instruction. Words: 1 Cycles: 2 Q Cycle Activity: 1st cycle: Q1 Q2 Decode 2nd cycle: Q1 No operation Example Q3 No operation Q2 Process data Q3 No operation HERE No operation Q4 No operation Q4 No operation RETURN After Instruction PC = TOS 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-35 PICmicro MID-RANGE MCU FAMILY RLF Rotate Left f through Carry Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: See description below Status Affected: C Encoding: Description: 00 RLF f,d 1101 dfff ffff The contents of register 'f' are rotated one bit to the left through the Carry Flag. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is stored back in register 'f'. C Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' RLF Register f Q4 Process data Write to destination REG1,0 Before Instruction REG1= C = 1110 0110 0 After Instruction REG1=1110 0110 W =1100 1100 C =1 Example 2 Case 1: RLF INDF, 1 Before Instruction W = xxxx xxxx FSR = 0xC2 Contents of Address (FSR) = 0011 1010 C = 1 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0111 0101 C = 0 Case 2: Before Instruction W = xxxx xxxx FSR = 0xC2 Contents of Address (FSR) = 1011 1001 C = 0 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0111 0010 C = 1 DS31029A-page 29-36 1997 Microchip Technology Inc. Section 29. Instruction Set RRF Rotate Right f through Carry Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: See description below Status Affected: C Encoding: Description: 00 RRF f,d 1100 dfff ffff The contents of register 'f' are rotated one bit to the right through the Carry Flag. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. C Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' Q4 Process data RRF Register f Write to destination REG1,0 Before Instruction REG1= 1110 0110 W = xxxx xxxx C = 0 After Instruction REG1= 1110 0110 W = 0111 0011 C = 0 Example 2 Case 1: RRF INDF, 1 29 Before Instruction Instruction Set W = xxxx xxxx FSR = 0xC2 Contents of Address (FSR) = 0011 1010 C = 1 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 1001 1101 C = 0 Case 2: Before Instruction W = xxxx xxxx FSR = 0xC2 Contents of Address (FSR) = 0011 1001 C = 0 After Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0001 1100 C = 1 1997 Microchip Technology Inc. DS31029A-page 29-37 PICmicro MID-RANGE MCU FAMILY SLEEP Syntax: [ label ] Operands: None Operation: 00h WDT, 0 WDT prescaler count, 1 TO, 0 PD Status Affected: TO, PD Encoding: 00 0000 0110 0011 Description: The power-down status bit, PD is cleared. Time-out status bit, TO is set. Watchdog Timer and its prescaler count are cleared. The processor is put into SLEEP mode with the oscillator stopped. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example: Note: DS31029A-page 29-38 SLEEP No operation Q3 No operation Q4 Go to sleep SLEEP The SLEEP instruction does not affect the assignment of the WDT prescaler 1997 Microchip Technology Inc. Section 29. Instruction Set SUBLW Subtract W from Literal Syntax: [ label ] Operands: 0 k 255 Operation: k - (W) W Status Affected: C, DC, Z Encoding: Description: SUBLW k 11 110x Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1: Case 1: kkkk kkkk The W register is subtracted (2's complement method) from the eight bit literal 'k'. The result is placed in the W register. Q3 Read literal 'k' SUBLW Process data Q4 Write to W register 0x02 Before Instruction W C Z = 0x01 = x = x After Instruction W C Z Case 2: = 0x01 = 1 = 0 ; result is positive Before Instruction W C Z = 0x02 = x = x After Instruction W C Z 29 ; result is zero Before Instruction W C Z Instruction Set Case 3: = 0x00 = 1 = 1 = 0x03 = x = x After Instruction W C Z Example 2 SUBLW = 0xFF = 0 = 0 ; result is negative MYREG Before Instruction W = 0x10 Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W C 1997 Microchip Technology Inc. = 0x27 = 1 ; result is positive DS31029A-page 29-39 PICmicro MID-RANGE MCU FAMILY SUBWF Subtract W from f Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) - (W) destination Status Affected: C, DC, Z Encoding: Description: 00 0010 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Example 1: Case 1: dfff ffff Subtract (2's complement method) W register from register 'f'. If 'd' is 0 the result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: Decode SUBWF f,d Q3 Read register 'f' SUBWF Q4 Process data Write to destination REG1,1 Before Instruction REG1= W = C = Z = 3 2 x x After Instruction REG1= W = C = Z = Case 2: 1 2 1 0 ; result is positive Before Instruction REG1= W = C = Z = 2 2 x x After Instruction REG1= W = C = Z = Case 3: 0 2 1 1 ; result is zero Before Instruction REG1= W = C = Z = 1 2 x x After Instruction REG1= W = C = Z = DS31029A-page 29-40 0xFF 2 0 0 ; result is negative 1997 Microchip Technology Inc. Section 29. Instruction Set SWAPF Swap Nibbles in f Syntax: [ label ] SWAPF f,d Operands: 0 f 127 d [0,1] Operation: (f<3:0>) destination<7:4>, (f<7:4>) destination<3:0> Status Affected: None Encoding: 00 1110 dfff ffff Description: The upper and lower nibbles of register 'f' are exchanged. If 'd' is 0 the result is placed in W register. If 'd' is 1 the result is placed in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' SWAPF Process data Q4 Write to destination REG, 0 Before Instruction REG1= 0xA5 After Instruction REG1= 0xA5 W = 0x5A Example 2 SWAPF INDF, 1 Before Instruction W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x20 29 After Instruction Example 3 SWAPF Instruction Set W = 0x17 FSR = 0xC2 Contents of Address (FSR) = 0x02 REG, 1 Before Instruction REG1= 0xA5 After Instruction REG1= 0x5A 1997 Microchip Technology Inc. DS31029A-page 29-41 PICmicro MID-RANGE MCU FAMILY TRIS Load TRIS Register Syntax: [ label ] TRIS Operands: 5f7 Operation: (W) TRIS register f; Status Affected: None Encoding: 00 0000 f 0110 0fff Description: The instruction is supported for code compatibility with the PIC16C5X products. Since TRIS registers are readable and writable, the user can directly address them. Words: 1 Cycles: 1 Example To maintain upward compatibility with future PIC16CXX products, do not use this instruction. DS31029A-page 29-42 1997 Microchip Technology Inc. Section 29. Instruction Set XORLW Exclusive OR Literal with W Syntax: [ label] Operands: 0 k 255 Operation: (W).XOR. k W Status Affected: Z Encoding: Description: XORLW k 11 1010 Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 kkkk kkkk The contents of the W register are XOR'ed with the eight bit literal 'k'. The result is placed in the W register. Q3 Read literal 'k' Q4 Process data XORLW Write to W register 0xAF Before Instruction W = 0xB5 After Instruction W Z Example 2 XORLW ; 1010 1111 (0xAF) ; 1011 0101 (0xB5) ; --------- ------ ; 0001 1010 (0x1A) = 0x1A = 0 MYREG Before Instruction W = 0xAF Address of MYREG = 0x37 MYREG is a symbol for a data memory location After Instruction W Z XORLW HIGH (LU_TABLE) Before Instruction W = 0xAF Address of LU_TABLE = 0x9375 LU_TABLE is a label for an address in program memory After Instruction W Z 1997 Microchip Technology Inc. = 0x3C = 0 DS31029A-page 29-43 Instruction Set Example 3 29 = 0x18 = 0 PICmicro MID-RANGE MCU FAMILY XORWF Exclusive OR W with f Syntax: [ label ] XORWF Operands: 0 f 127 d [0,1] Operation: (W).XOR. (f) destination Status Affected: Z Encoding: 00 0110 f,d dfff ffff Description: Exclusive OR the contents of the W register with register 'f'. If 'd' is 0 the result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Decode Example 1 Q3 Read register 'f' XORWF Process data Q4 Write to destination REG, 1 ; 1010 1111 (0xAF) Before Instruction ; 1011 0101 (0xB5) ; --------; 0001 1010 -----(0x1A) REG, 0 ; 1010 1111 (0xAF) Before Instruction ; 1011 0101 (0xB5) ; --------; 0001 1010 -----(0x1A) REG= 0xAF W = 0xB5 After Instruction REG= 0x1A W = 0xB5 Example 2 XORWF REG= 0xAF W = 0xB5 After Instruction REG= 0xAF W = 0x1A Example 3 XORWF INDF, 1 Before Instruction W = 0xB5 FSR = 0xC2 Contents of Address (FSR) = 0xAF After Instruction W = 0xB5 FSR = 0xC2 Contents of Address (FSR) = 0x1A DS31029A-page 29-44 1997 Microchip Technology Inc. Section 29. Instruction Set 29.6 Design Tips Question 1: How can I modify the value of W directly? I want to decrement W. Answer 1: There are a few possibilities, two are: 1. 2. For the midrange devices, there are several instructions that work with a literal and W. For instance, if it were desired to decrement W, this can be done with an ADDLW 0xFF. (the 0x prefix denotes hex to the assembler) Notice that all of the instructions can modify a value right where it sits in the file register. This means you can decrement it right where it is. You do not even need to move it to W. If you want to decrement it AND move it somewhere else, then you make W the DESTINATION of the decrement (DECF register,W) then put it where you want it. It is the same number of instructions as a straight move, but it gets decremented along the way. Question 2: Is there any danger in using the TRIS instruction for the PIC16CXXX since there is a warning in the Data book suggesting it not be used? Answer 2: For code compatibility and upgrades to later parts, the use of the TRIS instruction is not recommended. You should note the TRIS instruction is limited to ports A, B and C. Future devices may not support these instructions. Question 3: Do I have to switch to Bank1 of data memory before using the TRIS instruction (for parts with TRIS registers in the memory map)? Answer 3: No. The TRIS instruction is Bank independent. Again the use of the TRIS instruction is not recommended. Question 4: I have seen references to "Read-Modify-Write" instructions in your data sheet, but I do not know what that is. Can you explain what it is and why I need to know this? Answer 4: One situation where you would want to consider the affects of a R-M-W instruction is a port that is continuously changed from input to output and back. For example, say you have TRISB set to all outputs, and write all ones to the PORTB register, all of the PORTB pins will go high. Now, say you turn pin RB3 into an input, which happens to go low. A BCF PORTB,6 is then executed to drive pin RB6 low. If you then turn RB3 back into an output, it will now drive low, even though the last value you put there was a one. What happened was that the BCF of the other pin (RB6) caused the whole port to be read, including the zero on RB3 when it was an input. Then, bit 6 was changed as requested, but since RB3 was read as a zero, zero will also be placed back into that port latch, overwriting the one that was there before. When the pin is turned back into an output, the new value was reflected. 1997 Microchip Technology Inc. DS31029A-page 29-45 29 Instruction Set An easy example of a Read-Modify-Write (R-M-W) instruction is the bit clear instruction BCF. You might think that the processor just clears the bit, which on a port output pin would clear the pin. What actually happens is the whole port (or register) is first read, THEN the bit is cleared, then the new modified value is written back to the port (or register). Actually, any instruction that depends on a value currently in the register is going to be a Read-Modify-Write instruction. This includes ADDWF, SUBWF, BCF, BSF, INCF, XORWF, etc... Instructions that do not depend on the current register value, like MOVWF, CLRF, and so on are not R-M-W instructions. PICmicro MID-RANGE MCU FAMILY Question 5: When I perform a BCF other pins get cleared in the port. Why? Answer 5: There are a few possibilities, two are: 1. 2. DS31029A-page 29-46 Another case where a R-M-W instruction may seem to change other pin values unexpectedly can be illustrated as follows: Suppose you make PORTC all outputs and drive the pins low. On each of the port pins is an LED connected to ground, such that a high output lights it. Across each LED is a 100 F capacitor. Let's also suppose that the processor is running very fast, say 20 MHz. Now if you go down the port setting each pin in order; BSF PORTC,0 then BSF PORTC,1 then BSF PORTC,2 and so on, you may see that only the last pin was set, and only the last LED actually turns on. This is because the capacitors take a while to charge. As each pin was set, the pin before it was not charged yet and so was read as a zero. This zero is written back out to the port latch (R-M-W, remember) which clears the bit you just tried to set the instruction before. This is usually only a concern at high speeds and for successive port operations, but it can happen so take it into consideration. If this is on a PIC16C7X device, you may not have configured the I/O pins properly in the ADCON1 register. If a pin is configured for analog input, any read of that pin will read a zero, regardless of the voltage on the pin. This is an exception to the normal rule that the pin state is always read. You can still configure an analog pin as an output in the TRIS register, and drive the pin high or low by writing to it, but you will always read a zero. Therefore if you execute a Read-Modify-Write instruction (see previous question) all analog pins are read as zero, and those not directly modified by the instruction will be written back to the port latch as zero. A pin configured as analog is expected to have values that may be neither high nor low to a digital pin, or floating. Floating inputs on digital pins are a no-no, and can lead to high current draw in the input buffer, so the input buffer is disabled. 1997 Microchip Technology Inc. Section 29. Instruction Set 29.7 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the instruction set are: Currently No related Application Notes 29 Instruction Set 1997 Microchip Technology Inc. DS31029A-page 29-47 PICmicro MID-RANGE MCU FAMILY 29.8 Revision History Revision A This is the initial released revision of the Instruction Set description. DS31029A-page 29-48 1997 Microchip Technology Inc. M Section 30. Electrical Specifications HIGHLIGHTS 30.1 Introduction ..................................................................................................................30-2 30.2 Absolute Maximums.....................................................................................................30-3 30.3 Device Selection Table .................................................................................................30-4 30.4 Device Voltage Specifications ......................................................................................30-5 30.5 Device Current Specifications ......................................................................................30-6 30.6 Input Threshold Levels .................................................................................................30-9 30.7 I/O Current Specifications ..........................................................................................30-10 30.8 Output Drive Levels....................................................................................................30-11 30.9 I/O Capacitive Loading...............................................................................................30-12 30.10 Data EEPROM / Flash ...............................................................................................30-13 30.11 LCD............................................................................................................................30-14 30.12 Comparators and Voltage Reference .........................................................................30-15 30.13 Timing Parameter Symbology....................................................................................30-16 30.14 Example External Clock Timing Waveforms and Requirements ................................30-17 30.15 Example Power-up and Reset Timing Waveforms and Requirements.......................30-19 30.16 Example Timer0 and Timer1 Timing Waveforms and Requirements .........................30-20 30.17 Example CCP Timing Waveforms and Requirements................................................30-21 30.18 Example Parallel Slave Port (PSP) Timing Waveforms and Requirements ...............30-22 30.19 Example SSP and Master SSP SPI Mode Timing Waveforms and Requirements ....30-23 30.20 Example SSP I2C Mode Timing Waveforms and Requirements ................................30-27 30.21 Example Master SSP I2C Mode Timing Waveforms and Requirements ....................30-30 30.22 Example USART/SCI Timing Waveforms and Requirements ....................................30-32 30.23 Example 8-bit A/D Timing Waveforms and Requirements .........................................30-34 30.24 Example 10-bit A/D Timing Waveforms and Requirements .......................................30-36 30.25 Example Slope A/D Timing Waveforms and Requirements .......................................30-38 30.26 Example LCD Timing Waveforms and Requirements ................................................30-40 30.27 Related Application Notes..........................................................................................30-41 30.28 Revision History .........................................................................................................30-42 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A page 30-1 PICmicro MID-RANGE MCU FAMILY 30.1 Introduction This section is intended to show you the electrical specifications that may be specified in a particular device data sheet and what is meant by the specification. This section is NOT intended to give the values of these specifications. For the device specific values you must refer to the device's data sheet. All values show in this section should be considered as Example Values. In the description of the device and the functional modules (previous sections), there have been references to electrical specification parameters. These references have been hyperlinked in the electronic version to aid in the use of this manual. Note: Before starting any design, Microchip HIGHLY recommends that you acquire the most recent copy of the device data sheet and review the electrical specifications to ensure that they will meet your requirements. Throughout this section, certain terms will be used. Table 30-1 shows the conventions that will be used. Table 30-1: Term Conventions Term PIC16CXXX PIC16LCXXX PIC16FXXX PIC16LFXXX PIC16CRXXX PIC16LCRXXX PIC16XXXX-04 PIC16XXXX-08 PIC16XXXX-10 PIC16XXXX-20 LP osc XT osc HS osc RC osc Commercial Industrial Extended DS31030A-page 30-2 Description For devices tested to standard voltage range For devices tested to extended voltage range For devices tested to standard voltage range For devices tested to extended voltage range For devices tested to standard voltage range For devices tested to extended voltage range For devices that have been tested up to 4 MHz operation For devices that have been tested up to 8 MHz operation For devices that have been tested up to 10 MHz operation For devices that have been tested up to 20 MHz operation For devices configured with the LP device oscillator selected For devices configured with the XT device oscillator selected For devices configured with the HS device oscillator selected For devices configured with the RC device oscillator selected For devices with the commercial temperature range grading (0C TA +70C) For devices with the industrial temperature range grading (-40C TA +85C) For devices with the extended temperature range grading (-40C TA +125C) 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.2 Absolute Maximums The Absolute Maximum Ratings specify the worst case conditions that can be applied to the device. These ratings are not meant as operational specifications, and stresses above the listed values may cause damage to the device. Specifications are not always stand-alone, that is, the specification may have other requirements as well. An example of this is the "maximum current sourced/sunk by any I/O pin". The number of I/O pins that can be sinking/sourcing current, at any one time, is dependent upon the maximum current sunk/source by the port(s) (combined) and the maximum current into the VDD pin or out of the VSS pin. In this example, the physical reason is the Power and Ground bus width to the I/O ports and internal logic. If these specifications are exceeded, then electromigration may occur on these Power and Ground buses. Over time electromigration would cause these buses to open (be disconnected from the pin), and therefore cause the logic attached to these buses to stop operating. So exceeding the absolute specifications may cause device reliability issues. Input Clamp Current is defined as the current through the diode to VSS/VDD if pin voltage exceeds specification. Example Absolute Maximum Ratings Ambient temperature under bias........................................................................... . -55 to +125C Storage temperature .......................................................................................... -65C to +150C Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4)..... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ....................................................................... -0.3 to +7.5V Voltage on MCLR with respect to VSS (2) ...................................................................... 0 to +14V Voltage on RA4 with respect to Vss .............................................................................. 0 to +14V Total power dissipation (1) .................................................................................................... 1.0W Maximum current out of VSS pin ...................................................................................... 300 mA Maximum current into VDD pin ......................................................................................... 250 mA Input clamp current, IIK (VI < 0 or VI > VDD).................................................................... 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ............................................................. 20 mA Maximum output current sunk by any I/O pin..................................................................... 25 mA Maximum output current sourced by any I/O pin ............................................................... 25 mA Maximum current sunk by PORTA, PORTB, and PORTE (combined)............................. 200 mA Maximum current sourced by PORTA, PORTB, and PORTE (combined) ....................... 200 mA Maximum current sunk by PORTC and PORTD (combined) ........................................... 200 mA Maximum current sourced by PORTC and PORTD (combined)...................................... 200 mA Maximum current sourced by PORTC and PORTD (combined)...................................... 200 mA Maximum current sourced by PORTF and PORTG (combined) ...................................... 100 mA Maximum current sourced by PORTF and PORTG (combined) ...................................... 100 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOl x IOL) Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR pin rather than pulling this pin directly to VSS. 30 1997 Microchip Technology Inc. DS31030A-page 30-3 Electrical Specifications NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. PICmicro MID-RANGE MCU FAMILY 30.3 Device Selection Table This table in the Device Data Sheet is intended to assist you in determining which oscillators are tested for which devices, and some of the specifications that are tested. Any oscillator may be selected at time of programming, but only the specified oscillator is tested by Microchip. Since the RC and XT oscillators are only rated to 4 MHz, they are only tested on the -04 (4 MHz) devices. PICmicros rated for 10 MHz or 20 MHz are only tested in HS mode. In Table 30-2 the IPD is grayed out for the HS mode since there is not an IPD test point within the voltage range of the HS oscillator. The value shown is a typical value from characterization. Battery applications usually require an extended voltage range. Devices marked LC have an extended voltage range and have the RC, XT, and LP oscillators tested. Windowed devices are superset devices and have had the oscillators tested to all the specification ranges of the -04, -20, and LC devices. The temperature range that the device is tested to should be considered commercial, though at a later time they may be tested to industrial or extended temperature levels. Table 30-2: OSC PIC16LCXXX-04 Windowed Devices RC VDD: 4.0V to 6.0V IDD: 5 mA max. at 5.5V IPD: 16 A max. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 A typ. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 A typ. at 4V Freq: 4 MHz max. VDD: 2.5V to 6.0V IDD: 3.8 mA max. at 3.0V IPD: 5 A max. at 3V Freq: 4 MHz max. VDD: 2.5V to 6.0V IDD: 3.8 mA max. at 5.5V IPD: 16 A max. at 4V Freq: 4 MHz max. XT VDD: 4.0V to 6.0V IDD: 5 mA max. at 5.5V IPD: 16 A max. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 A typ. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V IDD: 2.7 mA typ. at 5.5V IPD: 1.5 A typ. at 4V Freq: 4 MHz max. VDD: 2.5V to 6.0V IDD: 3.8 mA max. at 3.0V IPD: 5 A max. at 3V Freq: 4 MHz max. VDD: 2.5V to 6.0V IDD: 3.8 mA max. at 5.5V IPD: 16 A max. at 4V Freq: 4 MHz max. VDD: 4.5V to 5.5V VDD: 4.5V to 5.5V VDD: 4.5V to 5.5V IDD: 13.5 mA typ. at 5.5V IDD: 10 mA max. at 5.5V IDD: 20 mA max. at 5.5V IPD: 1.5 A typ. at 4.5V IPD: 1.5 A typ. at 4.5V IPD: 1.5 A typ. at 4.5V Freq: 4 MHz max. Freq: 10 MHz max. Freq: 20 MHz max. HS LP PIC16CXXX-04 Example Cross Reference of Device Specifications for Oscillator Configurations and Frequencies of Operation (Commercial Devices) VDD: 4.0V to 6.0V IDD: 52.5 A typ. at 32 kHz, 4.0V IPD: 0.9 A typ. at 4.0V Freq: 200 kHz max. PIC16CXXX-10 Not recommended for use in LP mode PIC16CXXX-20 Not recommended for use in LP mode VDD: 4.5V to 5.5V Not recommended for use in HS mode IDD: 20 mA max. at 5.5V IPD: 1.5 A typ. at 4.5V Freq: 20 MHz max. VDD: 2.5V to 6.0V IDD: 48 A max. at 32 kHz, 3.0V IPD: 5.0 A max. at 3.0V Freq: 200 kHz max. VDD: 2.5V to 6.0V IDD: 48 A max. at 32 kHz, 3.0V IPD: 5.0 A max. at 3.0V Freq: 200 kHz max. The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifications. It is recommended that the user select the device type that ensures the specifications required. Note: DS31030A-page 30-4 Devices that are marked with Engineering Sample (ENG SMP) are tested to the current engineering test program at time of the device testing. There is no implied warranty that these devices have been tested to any or all specifications in the Device Data Sheet. 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.4 Device Voltage Specifications These specifications relate to the device VDD and the device power-up and function. Supply Voltage is the voltage level that must be applied to the device for the proper functional operation. Ram Data Retention Voltage is the level that the device voltage may be at and still retain the data value. VDD Start Voltage to ensure the internal Power-on Reset signal, is the level that VDD must start from to ensure that the POR circuitry will operate properly. VDD Rise Rate to ensure internal Power-on Reset signal, is the minimum slope that VDD must rise at to cause the POR circuitry to trip. Brown-out Reset Voltage is the voltage range where the brown-out circuitry may trip. When the BOR circuitry trips, the device will either be in brown-out reset, or just came out of brown-out reset. Table 30-3: Example DC Characteristics DC CHARACTERISTICS Param No. Symbol Characteristic VDD Supply Voltage PIC16CXXX PIC16LCXXX PIC16CXXX RAM Data Retention Voltage(1) VDD Start Voltage to ensure internal Power-on Reset signal VDD Rise Rate to ensure internal Power-on Reset signal Brown-out Reset Voltage D001 D001A D002 VDR D003 VPOR D004 SVDD VBOR D005 D005A Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial and -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions 4.0 2.5 4.5 1.5 -- -- -- -- 6.0 6.0 5.5 -- V V V V XT, RC and LP osc mode -- VSS -- V See section on Power-on Reset for details 0.05 -- -- 3.7 3.7 4.0 4.0 4.3 4.4 HS osc mode V/ms See section on Power-on Reset for details V V BODEN bit in Configuration Word enabled Extended Temperature Range Devices Only Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-5 PICmicro MID-RANGE MCU FAMILY 30.5 Device Current Specifications IDD is the current (I) that the device consumes when the device is in operating mode. This test is taken with all I/O as inputs, either pulled high or low. That is, there are no floating inputs, nor are any pins driving an output (with a load). IPD is the current (I) that the device consumes when the device is in sleep mode (power-down), referred to as power-down current. These tests are taken with all I/O as inputs, either pulled high or low. That is, there are no floating inputs, nor are any pins driving an output (with a load), weak pull-ups are disabled. A device may have certain features and modules that can operate while the device is in sleep mode. Some on these modules are: * * * * * * * Watchdog Timer (WDT) Brown-out Reset (BOR) circuitry Timer1 Analog to Digital converter LCD module Comparators Voltage Reference When all features are disabled, the device will consume the lowest possible current (the leakage current). If any of these features are operating while the device is in sleep, a higher current will occur. The difference between the lowest power mode (everything off) at only that one feature enabled (such as the WDT) is what we call the Module Differential Current. If more then one feature is enabled then the expected current can easily be calculated as: the base current (everything disabled and in sleep mode) plus all Module Differential Currents (delta currents). Example 30-1 shows an example of calculating the typical currents for a device at 5V, with the WDT and Timer1 oscillator enabled. Example 30-1: IPD Calculations with WDT and Timer1 Oscillator Enabled (@ 5V) Base Current WDT Delta Current Timer1 Delta Current Total Sleep Current DS31030A-page 30-6 14 nA 14 A 22 A 36 A ; Device leakage current ; 14 A - 14 nA = 14 A ; 22 A - 14 nA = 22 A ; 1997 Microchip Technology Inc. Section 30. Electrical Specifications Table 30-4: Example DC Characteristics DC CHARACTERISTICS Param Symbol No. IDD Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial and -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions Supply Current(2,4,5) XT, RC osc configuration (PIC16CXXX-04) FOSC = 4 MHz, VDD = 5.5V FOSC = 4 MHz, VDD = 3.0V D010 -- -- 2.7 2.0 5 3.8 mA mA D010A -- 22.5 48 A D010C -- 7.7 5 mA INTRC osc configuration, Fosc = 4 MHz, VDD = 5.5V D013 -- 13.5 30 mA HS osc configuration (PIC16CXXX-20) Fosc = 20 MHz, VDD = 5.5V D020 -- -- -- 10.5 7.5 1.5 42 30 21 A A A VDD = 4.0V, WDT enabled, -40C to +85C VDD = 3.0V, WDT enabled, -40C to +85C VDD = 4.0V, WDT disabled, -0C to +70C D021 -- -- 0.9 1.5 13.5 24 A A VDD = 3.0V, WDT disabled, 0C to +70C VDD = 4.0V, WDT disabled, -40C to +85C IPD LP osc configuration FOSC = 32 kHz, VDD = 3.0V, WDT disabled Power-down Current(3,5) A VDD = 3.0V, WDT disabled, -40C to +85C 18 0.9 -- A VDD = 4.0V, WDT disabled, -40C to +125C -- 1.5 -- * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Not Applicable. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. D021A D021B 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-7 PICmicro MID-RANGE MCU FAMILY Table 30-5: Example DC Characteristics DC CHARACTERISTICS Param No. Symbol D022 IWDT D022A IBOR D023 ICOMP IVREF ILCDRC ILCDVG IT1OSC IAD ISAD ISADVR D023A D024 D024A D025 D026 D027 D027A D027B D027C D027D Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Min Typ Max Units Conditions Module Differential Current (5) Watchdog Timer Brown-out Reset -- -- -- 6.0 -- 350 20 25 425 A A A VDD = 4.0V -40C to +125C BODEN bit is clear, VDD = 5.0V VDD = 4.0V VDD = 4.0V VDD = 3.0V VDD = 3.0V VDD = 3.0V A/D on, not converting REFOFF = 0 REFOFF = 0 Comparator (per Comparator) -- 85 100 A Voltage Reference -- 94 300 A LCD internal RC osc enabled -- 6.0 20 A LCD voltage generation -- TBD TBD A Timer1 oscillator -- 3.1 6.5 A A/D Converter -- 1.0 -- A Slope A/D (Total) -- 165 * 250 * A Slope A/D -- 20 * 30 * A Bandgap Voltage Reference ISADCDAC Slope A/D -- 50 * 70 * A ADCON1<7:4> = 1111b Programmable Current Source ISADSREF Slope A/D -- 55 * 85 * A ADOFF = 0 Reference Voltage Divider ISADCMP Slope A/D -- 40 * 65 * A ADOFF = 0 Comparator Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS31030A-page 30-8 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.6 Input Threshold Levels The Input Low Voltage (VIL) is the voltage level that will be read as a logic '0'. An input may not read a '0' at a voltage level above this. All designs should be to the specification since device to device (and to a much lesser extent pin to pin) variations will cause this level to vary. The Input High Voltage (VIH) is the voltage level that will be read as a logic '1'. An input may read a '1' at a voltage level below this. All designs should be to the specification since device to device (and to a much lesser extent pin to pin) variations will cause this level to vary. The I/O pins with TTL levels are shown with two specifications. One is the industry standard TTL specification, which is specified for the voltage range of 4.5V to 5.5V. The other is a specification that operates over the entire voltage range of the device. The better of these two specifications may be used in the design. Table 30-6: Example DC Characteristics DC CHARACTERISTICS Param Symbol Characteristic No. VIL Input Low Voltage I/O ports: D030 with TTL buffer D030A with Schmitt Trigger buffer D031 D032 D033 VIH D040 MCLR, OSC1 (RC mode) OSC1 (XT, HS and LP modes)(1) Input High Voltage I/O ports: with TTL buffer D040A D041 with Schmitt Trigger buffer Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. Min Typ Max Units Conditions VSS -- -- -- 0.15VDD 0.8 V V For entire VDD range (4) 4.5V VDD 5.5V (4) VSS -- 0.2VDD V For entire VDD range VSS VSS -- -- 0.2VDD 0.3VDD V V 0.25VDD + 0.8V 2.0 -- VDD V For entire VDD range (4) -- VDD V 4.5V VDD 5.5V (4) 0.8VDD -- VDD V For entire VDD range MCLR 0.8VDD -- VDD V OSC1 0.7VDD -- VDD V (XT, HS and LP modes)(1) D043 OSC1 (RC mode) 0.9VDD -- VDD V D050 VHYS Hysteresis of Schmitt Trigger TBD -- -- V Inputs Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with an external clock while in RC mode. 2: Not Applicable. 3: Not Applicable. 4: The better of the two specifications may be used. For VIL this would be the higher voltage and for VIH this would be the lower voltage. D042 D042A DS31030A-page 30-9 Electrical Specifications 1997 Microchip Technology Inc. 30 PICmicro MID-RANGE MCU FAMILY 30.7 I/O Current Specifications The PORT/GIO Weak Pull-up Current is the additional current that the device will draw when the weak pull-ups are enabled. Leakage Currents are the currents that the device consumes, since the devices are manufactured in the real world and do not adhere to their ideal characteristics. Ideally there should be no current on an input, but due to the real world there is always some parasitic path that consumes negligible current. Table 30-7: Example DC Characteristics DC CHARACTERISTICS Param Symbol No. Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. Min Typ Max Units Conditions D060 Input Leakage Current(2,3) I/O ports -- -- 1 A D060A CDAC -- -- 1 A D061 MCLR -- -- -- -- 5 5 A A 50 50 250 250 400 400 A A IIL D063 D070 D070A D160 IPU IPURB IPUGIO Weak Pull-up Current PORTB weak pull-up current GIO weak pull-up current Programmable Current Source (Slope A/D devices) Output Current 33.75 48.75 VDD = 5V, VPIN = VSS VDD = 5V, VPIN = VSS CDAC pin = 0V A ADCON1<7:4> = 1111b (full-scale) D160A 1.25 2.25 3.25 A ADCON1<7:4> = 0001b (1 LSB) D160B -0.5 0 0.5 A ADCON1<7:4> = 0000b (zero-scale) Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with an external clock while in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. DS31030A-page 30-10 18.75 Vss VPIN VDD, Pin at hi-impedance Vss VPIN VDD, Pin at hi-impedance Vss VPIN VDD Vss VPIN VDD, XT, HS and LP osc modes 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.8 Output Drive Levels The Output Low Voltage (VOL) of an I/O pin depends on the external connections to that I/O. If an I/O pin is shorted to VDD, no matter the drive capability of the I/O pin, a low level would not be reached (and the device would consume excessive drive current). The VOL is the output voltage that the I/O pin will drive, given the I/O does not need to sink more then the IOL current (at the specified device voltage) as specified in the conditions portion of the specification. The Output High Voltage (VOH) of an I/O pin depends on the external connections to that I/O. If an I/O pin is shorted to VSS, no matter the drive capability of the I/O pin, a high level would not be reached (and the device would consume excessive drive current). The VOH is the output voltage that the I/O pin will drive, given the I/O does not need to source more then the IOH current (at the specified device voltage) as specified in the conditions portion of the specification. Table 30-8: Example DC Characteristics DC CHARACTERISTICS Param Symbol Characteristic No. Output Low Voltage VOL D080 I/O ports D080A OSC2/CLKOUT (RC mode) D083 D083A VOH D090 Output High Voltage(3) I/O ports D090A OSC2/CLKOUT (RC mode) D092 D092A D150 VOD D170 VPCS SNPCS D171 -- -- 0.6 V -- -- 0.6 V -- -- 0.6 V -- -- 0.6 V VDD - 0.7 -- -- V VDD - 0.7 -- -- V VDD - 0.7 -- -- V VDD - 0.7 -- -- V -- -- 12 V Vss - 0.1 -- VDD - 1.4 -0.01 -- 1.14 1.19 IOH = -3.0 mA, VDD = 4.5V, -40C to +85C IOH = -2.5 mA, VDD = 4.5V, -40C to +125C IOH = -1.3 mA, VDD = 4.5V, -40C to +85C IOH = -1.0 mA, VDD = 4.5V, -40C to +125C RA4 pin CDAC pin Vss VCDAC VDD - 1.4 V DS31030A-page 30-11 30 Electrical Specifications 1997 Microchip Technology Inc. 1.24 V %/V IOL = 8.5 mA, VDD = 4.5V, -40C to +85C IOL = 7.0 mA, VDD = 4.5V, -40C to +125C IOL = 1.6 mA, VDD = 4.5V, -40C to +85C IOL = 1.2 mA, VDD = 4.5V, -40C to +125C on AN0 pin when AMUXOE =1 and ADCS3:ADSC0 = 0100b Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with an external clock while in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. D180 VBGR Open-drain High Voltage Programmable Current Source Output Voltage Range Output Voltage Sensitivity Bandgap Reference Output Voltage Range Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. Min Typ Max Units Conditions PICmicro MID-RANGE MCU FAMILY 30.9 I/O Capacitive Loading These specifications indicate the conditions that the I/O pins have on them from the device tester. These loadings effect the specifications for the timing specifications. If the loading in you application are different, then you will need to determine how this will effect the characteristic of the device in your system. Capacitances less then these specifications should not have effects on a system. Table 30-9: Example DC Characteristics DC CHARACTERISTICS Param No. Symbol Capacitive Loading Specs on Output Pins OSC2 pin In XT, HS and LP modes when external clock is used to drive OSC1. D101 CIO All I/O pins and OSC2 -- -- 50 pF To meet the Timing Specifications (in RC mode) of the Device D102 CB SCL, SDA -- -- 400 pF In I2C mode Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with external clock in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. D100 COSC2 Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. Min Typ Max Units Conditions DS31030A-page 30-12 -- -- 15 pF 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.10 Data EEPROM / Flash Table 30-10: Example Data EEPROM / Flash Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. DC CHARACTERISTICS Param Symbol No. D120 D121 D122 D130 D131 Characteristic Data EEPROM Memory Endurance ED VDRW VDD for read/write TDEW Erase/Write cycle time Program Flash Memory EP Endurance VPR VDD for read Min Typ Max 1M VMIN 10M -- 6.0 -- -- 10 100 VMIN 1000 -- -- 6.0 -- Units Conditions E/W 25C at 5V V VMIN = Minimum operating voltage ms E/W V VMIN = Minimum operating voltage -- D132 VPEW VDD for erase/write 4.5 5.5 V -- -- 10 D133 TPEW Erase/Write cycle time ms Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-13 PICmicro MID-RANGE MCU FAMILY 30.11 LCD Table 30-11: Example LCD Module Electrical Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. DC CHARACTERISTICS Param Symbol Characteristic No. Min Typ Max Units Conditions D200 VLCD3 LCD Voltage on pin VLCD3 VDD - 0.3 -- Vss + 7.0 V D201 VLCD2 LCD Voltage on pin VLCD2 -- -- VLCD3 V D202 VLCD1 LCD Voltage on pin VLCD1 -- -- VDD V D210 RCOM Com Output Source Impedance -- -- 1k COM outputs D211 RSEG Seg Output Source Impedance -- -- 10k SEG outputs D220 VOH Output High Voltage Max (VLCDN) - 0.1 -- Max (VLCDN) V COM outputs IOH = 25 A SEG outputs IOH = 3 A D221 VOL Output Low Voltage Min (VLCDN) -- Min (VLCDN) + 0.1 V COM outputs IOL = 25 A SEG outputs IOL = 3 A Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: 0 ohm source impedance at VLCD. Table 30-12: Example VLCD Charge Pump Electrical Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. DC CHARACTERISTICS Param No. Symbol Characteristic Min Typ Max Units D250 IVADJ VLCDADJ Regulated Current Output -- 10 -- A D251 Ivr VLCDADJ Current Consumption -- -- 20 A D252 IVADJ VDD VLCDADJ Current VDD Rejection -- -- 0.1/1 A/V D253 IVADJ T VLCDADJ Current Variation With Temperature -- -- 0.1/70 A/C D260(1) RVADJ VLCDADJ External Resistor 100 -- 230 k D265 VVADJ VLCDADJ Voltage Limits 1.0 -- 2.3 V D271(1) CECPC External Charge Pump Capacitance -- 0.5 -- F Conditions Note 1: For design guidance only. DS31030A-page 30-14 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.12 Comparators and Voltage Reference Table 30-13: Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. DC CHARACTERISTICS Param Symbol No. Example Comparator Characteristics Characteristics Min Typ Max Units D300 VIOFF Input offset voltage -- 5.0 10 mV D301 VICM Input common mode voltage 0 -- VDD - 1.5 V D302 CMRR Common Mode Rejection Ratio 300 TRESP Response Time(1) 35 70 -- db PIC16CXXX -- 150 400 ns PIC16LCXXX -- 210 600 ns TMC2OV Comparator Mode Change to Output Valid -- -- 10 s 300A 301 Comments Note 1: Response time measured with one comparator input at (VDD - 1.5)/2 while the other input transitions from VSS to VDD. Table 30-14: Example Voltage Reference Characteristics DC CHARACTERISTICS Param Symbol No. Characteristics Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. Min Typ Max Units D310 VRES Resolution VDD/32 -- VDD/24 V D311 VRAA Absolute Accuracy -- -- -- -- 1/4 1/2 LSb LSb D312 VRUR Unit Resistor Value (R) -- 2k -- 310 TSET Settling Time(1) -- -- 10 s Comments Low Range (VRR = 1) High Range (VRR = 0) Note 1: Settling time measured while VRR = 1 and VR3:VR0 transitions from 0000 to 1111. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-15 PICmicro MID-RANGE MCU FAMILY 30.13 Timing Parameter Symbology The timing parameter symbols have been created with one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (Hi-impedance) L Low I2C only AA output access BUF Bus free TCC:ST (I2C specifications only) CC HD Hold ST DAT DATA input hold STA START condition Figure 30-1: 3. TCC:ST (I2C specifications only) 4. Ts (I2C specifications only) T Time osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T1CKI WR P R V Z Period Rise Valid Hi-impedance High Low High Low SU Setup STO STOP condition Example Load Conditions Load condition 2 Load condition 1 VDD/2 RL CL Pin VSS RL = 464 CL = 50 pF for all pins except OSC2 15 pF for OSC2 output DS31030A-page 30-16 CL Pin VSS 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.14 Example External Clock Timing Waveforms and Requirements Figure 30-2: Q4 Example External Clock Timing Waveforms Q1 Q2 Q3 Q4 Q1 OSC1 1 3 3 4 4 2 CLKOUT Table 30-15: Param. Symbol No. Characteristic External CLKIN Frequency(1) Min Typ Max Units DC -- 4 MHz Conditions 1997 Microchip Technology Inc. DS31030A-page 30-17 30 Electrical Specifications XT and RC osc PIC16CXXX-04 PIC16LCXXX-04 DC -- 10 MHz HS osc PIC16CXXX-10 DC -- 20 MHz PIC16CXXX-20 DC -- 200 kHz LP osc PIC16LCXXX-04 Oscillator Frequency(1) DC -- 4 MHz RC osc PIC16CXXX-04 PIC16LCXXX-04 0.1 -- 4 MHz XT osc PIC16CXXX-04 PIC16LCXXX-04 4 -- 10 MHz HS osc PIC16CXXX-10 4 -- 20 MHz PIC16CXXX-20 5 -- 200 kHz LP osc mode PIC16LCXXX-04 1 Tosc External CLKIN Period(1) 250 -- -- ns XT and RC osc PIC16CXXX-04 PIC16LCXXX-04 100 -- -- ns HS osc PIC16CXXX-10 50 -- -- ns PIC16CXXX-20 5 -- -- s LP osc PIC16LCXXX-04 Oscillator Period(1) 250 -- -- ns RC osc PIC16CXXX-04 PIC16LCXXX-04 250 -- 10,000 ns XT osc PIC16CXXX-04 PIC16LCXXX-04 100 -- 250 ns HS osc PIC16CXXX-10 50 -- 250 ns PIC16CXXX-20 5 -- -- s LP osc PIC16LCXXX-04 2 TCY Instruction Cycle Time(1) 200 -- DC ns TCY = 4/FOSC 3 TosL, External Clock in (OSC1) 50 -- -- ns XT osc PIC16CXXX-04 TosH High or Low Time 60 -- -- ns XT osc PIC16LCXXX-04 2.5 -- -- s LP osc PIC16LCXXX-04 15 -- -- ns HS osc PIC16CXXX-20 4 TosR, External Clock in (OSC1) -- -- 25 ns XT osc PIC16CXXX-04 TosF Rise or Fall Time -- -- 50 ns LP osc PIC16LCXXX-04 -- -- 15 ns HS osc PIC16CXXX-20 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. 1A Fosc Example External Clock Timing Requirements PICmicro MID-RANGE MCU FAMILY Figure 30-3: Example CLKOUT and I/O Timing Waveforms Q1 Q4 Q2 Q3 OSC1 11 10 CLKOUT 13 14 19 12 18 16 I/O Pin (input) 15 17 I/O Pin (output) new value old value 20, 21 Note: Refer to Figure 30-1 for load conditions. Table 30-16: Param. No. 10 11 12 13 14 Example CLKOUT and I/O Timing Requirements Symbol TosH2ckL TosH2ckH TckR TckF TckL2ioV Characteristic OSC1 to CLKOUT OSC1 to CLKOUT CLKOUT rise time CLKOUT fall time CLKOUT to Port out valid Min Typ Max -- -- -- -- -- 75 75 35 35 -- 200 200 100 100 0.5TCY + 20 -- -- 150 -- -- Units Conditions ns ns ns ns ns (1) (1) (1) (1) (1) Port in valid before CLKOUT 0.25TCY + 25 -- ns (1) 16 Port in hold after CLKOUT 0 -- ns (1) 17 OSC1 (Q1 cycle) to Port out valid -- 50 ns 18 OSC1 (Q2 cycle) to PIC16CXXX 100 -- ns Port input invalid 18A PIC16LCXXX 200 -- ns (I/O in hold time) 19 TioV2osH Port input valid to OSC1 0 -- -- ns (I/O in setup time) 20 TioR Port output rise time PIC16CXXX -- 10 25 ns 20A PIC16LCXXX -- -- 60 ns 21 TioF Port output fall time PIC16CXXX -- 10 25 ns 21A PIC16LCXXX -- -- 60 ns 22 Tinp INT pin high or low time TCY -- -- ns 23 Trbp RB7:RB4 change INT high or low time TCY -- -- ns 24 Trcp RC7:RC4 change INT high or low time 20 ns Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. These parameters are asynchronous events not related to any internal clock edges. Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC. 15 TioV2ckH TckH2ioI TosH2ioV TosH2ioI DS31030A-page 30-18 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.15 Example Power-up and Reset Timing Waveforms and Requirements Figure 30-4: Example Reset, Watchdog Timer, Oscillator Start-up Timer and Power-up Timer Timing Waveforms VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal RESET Watchdog Timer RESET 31 34 34 I/O Pins Note: Refer to Figure 30-1 for load conditions. Figure 30-5: Brown-out Reset Timing BVDD VDD 35 Table 30-17: Param. No. Symbol TmcL Twdt 32 Tost 33 34 Tpwrt TIOZ 35 TBOR Characteristic Min Typ Max Units Conditions MCLR Pulse Width (low) Watchdog Timer Time-out Period (No Prescaler) Oscillation Start-up Timer Period Power up Timer Period I/O Hi-impedance from MCLR Low or Watchdog Timer Reset Brown-out Reset Pulse Width 2 7 -- 18 -- 33 s ms VDD = 5V, -40C to +125C VDD = 5V, -40C to +125C -- 1024TOSC -- -- TOSC = OSC1 period 28 -- 72 -- 132 2.1 ms s VDD = 5V, -40C to +125C 100 -- -- s VDD BVDD (See D005) Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 1997 Microchip Technology Inc. DS31030A-page 30-19 30 Electrical Specifications 31 30 Example Reset, Watchdog Timer, Oscillator Start-up Timer, Brown-out Reset, and Power-up Timer Requirements PICmicro MID-RANGE MCU FAMILY 30.16 Example Timer0 and Timer1 Timing Waveforms and Requirements Figure 30-6: Example Timer0 and Timer1 External Clock Timings Waveforms T0CKI 41 40 42 T1OSO/T1CKI 46 45 47 48 TMR0 or TMR1 Note: Refer to Figure 30-1 for load conditions. Table 30-18: Param Symbol No. Example Timer0 and Timer1 External Clock Requirements Characteristic 40 Tt0H T0CKI High Pulse Width 41 Tt0L T0CKI Low Pulse Width 42 Tt0P T0CKI Period 45 Tt1H T1CKI High Time 46 Tt1L 47 Tt1P No Prescaler With Prescaler No Prescaler With Prescaler Synchronous, no prescaler Synchronous, PIC16CXXX with prescaler PIC16LCXXX Asynchronous PIC16CXXX PIC16LCXXX T1CKI Synchronous, no prescaler Low Time Synchronous, PIC16CXXX with prescaler PIC16LCXXX Asynchronous PIC16CXXX PIC16LCXXX T1CKI Synchronous input period Asynchronous Ft1 48 Timer1 oscillator input frequency range (oscillator enabled by setting the T1OSCEN bit) Tcke2tmr Delay from external clock edge to timer I increment Min Typ Max Units 0.5TCY + 20 10 0.5TCY + 20 10 GREATER OF: 20 S OR TCY + 40 N 0.5TCY + 20 15 25 30 50 0.5TCY + 20 15 25 2TCY -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns GREATER OF: 20 S OR TCY + 40 N Greater of: 20S or 4TCY DC -- -- ns -- -- ns -- 200 kHz 2Tosc -- 7Tosc -- Conditions N = prescale value (1, 2, 4,..., 256) N = prescale value (1, 2, 4, 8) Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS31030A-page 30-20 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.17 Example CCP Timing Waveforms and Requirements Figure 30-7: Example Capture/Compare/PWM Timings Waveforms CCPx (Capture Mode) 50 51 52 CCPx (Compare or PWM Mode) 53 54 Note: Refer to Figure 30-1 for load conditions. Table 30-19: Param. Symbol No. 50 TccL 51 TccH 52 TccP 53 TccR 54 TccF Example Capture/Compare/PWM Requirements Characteristic CCPx input low time Min No Prescaler 0.5TCY + 20 With PIC16CXXX 10 Prescaler PIC16LCXXX 20 CCPx input No Prescaler 0.5TCY + 20 high time With PIC16CXXX 10 Prescaler PIC16LCXXX 20 CCPx input period 3TCY + 40 N CCPx output fall time PIC16CXXX -- PIC16LCXXX -- CCPx output fall time PIC16CXXX -- PIC16LCXXX -- Typ Max Units -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns ns ns 10 25 10 25 25 45 25 45 ns ns ns ns Conditions N = prescale value (1,4 or 16) Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-21 PICmicro MID-RANGE MCU FAMILY 30.18 Example Parallel Slave Port (PSP) Timing Waveforms and Requirements Figure 30-8: Example Parallel Slave Port Timing Waveforms RE2/CS RE0/RD RE1/WR 65 RD7:RD0 62 64 63 Note: Refer to Figure 30-1 for load conditions. Table 30-20: Example Parallel Slave Port Requirements Param. No. Symbol Characteristic Min Typ Max Units 62 TdtV2wrH 20 -- -- ns 63 TwrH2dtI 64 TrdL2dtV TrdH2dtI TibfINH Data in valid before WR or CS (setup time) WR or CS to data-in invalid PIC16CXXX (hold time) PIC16LCXXX RD and CS to data-out valid RD or CS to data-out invalid Inhibit of the IBF flag bit being cleared from WR or CS 20 35 -- 10 -- -- -- -- -- -- -- -- 80 30 3Tcy ns ns ns ns 65 66 Conditions Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This specification ensured by design. DS31030A-page 30-22 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.19 Example SSP and Master SSP SPI Mode Timing Waveforms and Requirements Figure 30-9: Example SPI Master Mode Timing (CKE = 0) SS 70 SCK (CKP = 0) 71 72 78 79 79 78 SCK (CKP = 1) 80 BIT6 - - - - - -1 MSb SDO LSb 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 73 Refer to Figure 30-1 for load conditions. Table 30-21: Param. No. 70 71 Symbol TssL2scH, TssL2scL TscH 71A 72 TscL 72A 73 73A 74 75 76 78 79 TscH2diL, TscL2diL TdoR Characteristic Min SS to SCK or SCK input TCY Typ Max Units -- -- ns Continuous 1.25TCY + 30 Single Byte 40 SCK input low time Continuous 1.25TCY + 30 (slave mode) Single Byte 40 Setup time of SDI data input to SCK edge 100 -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge 1.5TCY + 40 -- -- ns 100 -- -- ns -- -- -- -- -- -- -- -- 10 20 10 10 20 10 -- -- 25 45 25 25 45 25 50 100 ns ns ns ns ns ns ns ns SCK input high time (slave mode) SDO data output rise time PIC16CXXX PIC16LCXXX TdoF SDO data output fall time TscR SCK output rise time PIC16CXXX (master mode) PIC16LCXXX TscF SCK output fall time (master mode) TscH2doV, SDO data output valid PIC16CXXX TscL2doV after SCK edge PIC16LCXXX Conditions Note 1 Note 1 Note 1 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used. 1997 Microchip Technology Inc. DS31030A-page 30-23 30 Electrical Specifications 80 TdiV2scH, TdiV2scL TB2B Example SPI Mode Requirements (Master Mode, CKE = 0) PICmicro MID-RANGE MCU FAMILY Figure 30-10: Example SPI Master Mode Timing (CKE = 1) SS 81 SCK (CKP = 0) 71 72 79 73 SCK (CKP = 1) 80 78 BIT6 - - - - - -1 MSb SDO LSb 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 Refer to Figure 30-1 for load conditions. Table 30-22: Param. No. 71 Example SPI Mode Requirements (Master Mode, CKE = 1) Symbol TscH -- -- -- -- -- ns ns ns ns ns 1.5TCY + 40 -- -- ns 100 -- -- ns PIC16CXXX PIC16LCXXX -- SDO data output fall time SCK output rise time PIC16CXXX (master mode) PIC16LCXXX TscF SCK output fall time (master mode) TscH2doV, SDO data output valid PIC16CXXX TscL2doV after SCK edge PIC16LCXXX TdoV2scH, SDO data output setup to SCK edge TdoV2scL -- -- 10 20 10 10 20 10 -- -- -- 25 45 25 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns TscL 73A 74 75 76 78 79 80 81 TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TscR SCK input high time (slave mode) Continuous Single Byte SCK input low time Continuous (slave mode) Single Byte Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge Typ Max Units -- -- -- -- -- 72A 73 Min 1.25TCY + 30 40 1.25TCY + 30 40 100 71A 72 Characteristic SDO data output rise time -- -- TCY Conditions Note 1 Note 1 Note 1 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used. DS31030A-page 30-24 1997 Microchip Technology Inc. Section 30. Electrical Specifications Figure 30-11: Example SPI Slave Mode Timing (CKE = 0) SS 70 SCK (CKP = 0) 83 71 72 78 79 79 78 SCK (CKP = 1) 80 MSb SDO LSb BIT6 - - - - - -1 77 75, 76 SDI MSb IN BIT6 - - - -1 LSb IN 74 73 Refer to Figure 30-1 for load conditions. Table 30-23: Param. No. 70 71 Example SPI Mode Requirements (Slave Mode Timing (CKE = 0) Symbol TssL2scH, TssL2scL TscH 71A 72 TscL 72A 73 73A 74 75 76 77 78 79 83 TscH2diL, TscL2diL TdoR Min SS to SCK or SCK input TCY -- -- ns Continuous Single Byte SCK input low time Continuous (slave mode) Single Byte Setup time of SDI data input to SCK edge 1.25TCY + 30 40 1.25TCY + 30 40 100 -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge 1.5TCY + 40 -- -- ns 100 -- -- ns -- 10 20 10 -- 10 20 10 -- -- -- 25 45 25 50 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns ns SCK input high time (slave mode) SDO data output rise time PIC16CXXX PIC16LCXXX TdoF SDO data output fall time TssH2doZ SS to SDO output hi-impedance TscR SCK output rise time PIC16CXXX (master mode) PIC16LCXXX TscF SCK output fall time (master mode) TscH2doV, SDO data output valid PIC16CXXX TscL2doV after SCK edge PIC16LCXXX TscH2ssH, SS after SCK edge TscL2ssH Typ Max Units -- 10 -- -- -- 1.5TCY + 40 Conditions Note 1 Note 1 Note 1 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used. 1997 Microchip Technology Inc. DS31030A-page 30-25 30 Electrical Specifications 80 TdiV2scH, TdiV2scL TB2B Characteristic PICmicro MID-RANGE MCU FAMILY Figure 30-12: Example SPI Slave Mode Timing (CKE = 1) 82 SS 70 SCK (CKP = 0) 83 71 72 SCK (CKP = 1) 80 MSb SDO BIT6 - - - - - -1 LSb 75, 76 SDI MSb IN 77 BIT6 - - - -1 LSb IN 74 Refer to Figure 30-1 for load conditions. Table 30-24: Param. No. 70 71 Example SPI Slave Mode Mode Requirements (CKE = 1) Symbol Characteristic Min SS to SCK or SCK input TCY -- -- ns 1.25TCY + 30 40 1.25TCY + 30 40 1.5TCY + 40 -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns 100 -- -- ns PIC16CXXX PIC16LCXXX -- SDO data output fall time SS to SDO output hi-impedance SCK output rise time PIC16CXXX (master mode) PIC16LCXXX TscF SCK output fall time (master mode) TscH2doV, SDO data output valid PIC16CXXX TscL2doV after SCK edge PIC16LCXXX TssL2doV SDO data output valid PIC16CXXX after SS edge PIC16LCXXX TscH2ssH, SS after SCK edge TscL2ssH -- 10 -- -- -- -- -- -- -- 10 20 10 -- 10 20 10 -- -- -- -- -- 25 45 25 50 25 45 25 50 100 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns TssL2scH, TssL2scL TscH 71A 72 TscL 72A 73A 74 75 76 77 78 79 80 82 83 TB2B TscH2diL, TscL2diL TdoR TdoF TssH2doZ TscR SCK input high time (slave mode) Continuous Single Byte SCK input low time Continuous (slave mode) Single Byte Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time 1.5TCY + 40 Typ Max Units Conditions Note 1 Note 1 Note 1 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used. DS31030A-page 30-26 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.20 Example SSP I2C Mode Timing Waveforms and Requirements Figure 30-13: SCL Example SSP I2C Bus Start/Stop Bits Timing Waveforms 93 91 90 92 SDA STOP Condition START Condition Note: Refer to Figure 30-1 for load conditions. Table 30-25: Param. Symbol No. 90 91 92 93 TSU:STA Example SSP I2C Bus Start/Stop Bits Requirements Characteristic START condition Setup time THD:STA START condition Hold time TSU:STO STOP condition Setup time THD:STO STOP condition Hold time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Min Typ Max Units Conditions 4700 600 4000 600 4700 600 4000 600 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns Only relevant for repeated START condition ns After this period the first clock pulse is generated ns ns 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-27 PICmicro MID-RANGE MCU FAMILY Figure 30-14: 103 Example SSP I2C Bus Data Timing Waveforms 102 100 101 SCL 90 106 107 91 92 SDA In 109 109 110 SDA Out Note: Refer to Figure 30-1 for load conditions. DS31030A-page 30-28 1997 Microchip Technology Inc. Section 30. Electrical Specifications Table 30-26: Param. No. 100 101 102 103 Example SSP I2C Bus Data Requirements Symbol THIGH TLOW TR TF Characteristic Min Max Units Conditions 100 kHz mode 4.0 -- s 400 kHz mode 0.6 -- s PIC16CXXX must operate at a minimum of 1.5 MHz PIC16CXXX must operate at a minimum of 10 MHz SSP Module 100 kHz mode 1.5TCY 4.7 -- -- s 400 kHz mode 1.3 -- s SDA and SCL rise time SSP Module 100 kHz mode 400 kHz mode 1.5TCY -- 20 + 0.1Cb -- 1000 300 ns ns SDA and SCL fall time 100 kHz mode 400 kHz mode -- 20 + 0.1Cb 300 300 ns ns 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 4.7 0.6 4.0 0.6 0 0 250 100 4.7 0.6 -- -- 4.7 1.3 -- -- -- -- -- 0.9 -- -- -- -- 3500 -- -- -- s s s s ns s ns ns s s ns ns s s Clock high time Clock low time 90 TSU:STA START condition setup time 91 THD:STA START condition hold time 106 THD:DAT Data input hold time 107 TSU:DAT Data input setup time 92 TSU:STO STOP condition setup time 109 TAA Output valid from clock 110 TBUF Bus free time PIC16CXXX must operate at a minimum of 1.5 MHz PIC16CXXX must operate at a minimum of 10 MHz Cb is specified to be from 10 to 400 pF Cb is specified to be from 10 to 400 pF Only relevant for repeated START condition After this period the first clock pulse is generated Note 2 Note 1 Time the bus must be free before a new transmission can start D102 Cb Bus capacitive loading -- 400 pF Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but the requirement tsu;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line. TR max. + tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-29 PICmicro MID-RANGE MCU FAMILY 30.21 Example Master SSP I2C Mode Timing Waveforms and Requirements Figure 30-15: SCL Example Master SSP I2C Bus Start/Stop Bits Timing Waveforms 93 91 90 92 SDA STOP Condition START Condition Note: Refer to Figure 30-1 for load conditions. Table 30-27: Example Master SSP I2C Bus Start/Stop Bits Requirements Param. Symbol Characteristic No. 90 91 92 93 Min Typ Max Units TSU:STA START condition Setup time 100 kHz mode 2(TOSC)(BRG + 1) -- -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode (1) 2(TOSC)(BRG + 1) -- -- -- THD:STA START condition Hold time 100 kHz mode 2(TOSC)(BRG + 1) -- -- 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode (1) 2(TOSC)(BRG + 1) -- -- -- TSU:STO STOP condition 100 kHz mode 2(TOSC)(BRG + 1) -- Setup time 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode (1) 2(TOSC)(BRG + 1) -- -- -- -- ns THD:STO STOP condition 100 kHz mode 2(TOSC)(BRG + 1) -- Hold time 400 kHz mode 2(TOSC)(BRG + 1) -- 1 MHz mode (1) 2(TOSC)(BRG + 1) -- -- -- -- ns Conditions Only relevant for repeated START condition ns After this period the first clock pulse is generated ns This specification ensured by design. For the value required by the I2C specification, please refer to Figure A-11 of the "Appendix." Maximum pin capacitance = 10 pF for all I2C pins. DS31030A-page 30-30 1997 Microchip Technology Inc. Section 30. Electrical Specifications Figure 30-16: Example Master SSP I2C Bus Data Timing 103 102 100 101 SCL 90 106 91 92 107 SDA In 110 109 109 SDA Out Note: Refer to Figure 30-1 for load conditions. Example Master SSP I2C Bus Data Requirements Table 30-28: Param. Symbol Characteristic No. 100 THIGH Clock high time Min 100 kHz mode 400 kHz mode 2(TOSC)(BRG + 1) 2(TOSC)(BRG + 1) (1) 2(TOSC)(BRG + 1) 1 MHz mode 100 kHz mode 2(TOSC)(BRG + 1) 400 kHz mode 2(TOSC)(BRG + 1) 1 MHz mode (1) 2(TOSC)(BRG + 1) 101 TLOW Clock low time 102 TR SDA and SCL rise time 100 kHz mode 400 kHz mode 103 TF SDA and SCL fall time 1 MHz mode (1) 100 kHz mode 400 kHz mode 90 TSU:STA START condition setup time 91 THD:STA START condition hold time 106 THD:DAT Data input hold time 107 TSU:DAT Data input setup time 92 -- 20 + 0.1Cb -- -- 20 + 0.1Cb -- 1 MHz mode (1) 100 kHz mode 2(TOSC)(BRG + 1) 400 kHz mode 2(TOSC)(BRG + 1) 1 MHz mode (1) 2(TOSC)(BRG + 1) 100 kHz mode 400 kHz mode 2(TOSC)(BRG + 1) 2(TOSC)(BRG + 1) 1 MHz mode (1) 2(TOSC)(BRG + 1) 100 kHz mode 0 400 kHz mode 0 TBD 1 MHz mode (1) 100 kHz mode 400 kHz mode 250 100 TBD setup time 1 MHz mode (1) 100 kHz mode 2(TOSC)(BRG + 1) 400 kHz mode 2(TOSC)(BRG + 1) 1 MHz mode (1) 2(TOSC)(BRG + 1) TSU:STO STOP condition 109 TAA Output valid from clock 100 kHz mode 400 kHz mode 110 TBUF Bus free time 1 MHz mode (1) 100 kHz mode 400 kHz mode D102 Cb 1 MHz mode (1) Bus capacitive loading -- -- -- 4.7 1.3 TBD -- Max Units -- -- -- -- -- -- 1000 300 300 300 300 100 -- -- -- -- -- -- -- 0.9 -- -- -- -- -- -- -- 3500 1000 -- -- -- -- 400 ms ms ms ms ms ms ns ns ns ns ns ns ms ms ms ms ms ms ns ms ns ns ns ns ms ms ms ns ns ns ms ms ms pF Conditions Cb is specified to be from 10 to 400 pF Cb is specified to be from 10 to 400 pF Only relevant for repeated START condition After this period the first clock pulse is generated Note 2 Time the bus must be free before a new transmission can start Note 1: Maximum pin capacitance = 10 pF for all I2C pins. 2: A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but parameter 107 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line. Parameter 102.+ parameter 107 = 1000 + 250 = 1250 ns (for 100 kHz-mode) before the SCL line is released. 1997 Microchip Technology Inc. DS31030A-page 30-31 30 Electrical Specifications This specification ensured by design. For the value required by the I2C specification, please refer to Figure A-11 of the "Appendix." These parameters are for design guidance only and are not tested, nor characterized. PICmicro MID-RANGE MCU FAMILY 30.22 Example USART/SCI Timing Waveforms and Requirements Figure 30-17: TX/CK pin Example USART Synchronous Transmission (Master/Slave) Timing Waveforms 121 121 RX/DT pin 120 122 Note: Refer to Figure 30-1 for load conditions. Table 30-29: Param. No. 120 Symbol Example USART Synchronous Transmission Requirements Characteristic TckH2dtV SYNC XMIT (MASTER & SLAVE) Clock high to data out valid 121 Tckrf Clock out rise time and fall time (Master Mode) 122 Tdtrf Data out rise time and fall time PIC16CXXX PIC16LCXXX PIC16CXXX PIC16LCXXX PIC16CXXX PIC16LCXXX Min Typ Max -- -- -- -- -- -- -- -- -- -- -- -- 80 100 45 50 45 50 Units Conditions ns ns ns ns ns ns Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS31030A-page 30-32 1997 Microchip Technology Inc. Section 30. Electrical Specifications Figure 30-18: Example USART Synchronous Receive (Master/Slave) Timing Waveforms TX/CK pin 125 RX/DT pin 126 Note: Refer to Figure 30-1 for load conditions. Table 30-2: Param. No. Example USART Synchronous Receive Requirements Symbol 125 TdtV2ckl 126 TckL2dtl Characteristic SYNC RCV (MASTER & SLAVE) Data hold before CK (DT hold time) Data hold after CK (DT hold time) Min Typ Max Units 15 15 -- -- -- -- ns ns Conditions Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-33 PICmicro MID-RANGE MCU FAMILY 30.23 Example 8-bit A/D Timing Waveforms and Requirements Table 30-30: Example 8-bit A/D Converter Characteristics Param Symbol Characteristic No. Min Typ Max Units Conditions Resolution -- -- 8-bits bit Total Absolute error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A01 NR A02 EABS A03 EIL Integral linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A04 EDL Differential linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A05 EFS Full scale error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A06 EOFF Offset error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A10 -- Monotonicity -- guaranteed -- -- V A20 VREF Reference voltage A25 VAIN Analog input voltage A30 ZAIN Recommended impedance of analog voltage source A40 IAD A/D PIC16CXXX conversion PIC16LCXXX current (VDD) VREF input current (Note 2) A50 IREF 3.0V -- VDD + 0.3 VSS - 0.3 -- VREF + 0.3 V -- -- 10.0 k -- 180 -- A -- 90 -- A 10 -- 1000 A -- -- 10 A VREF = VDD = 5.12V, VSS VAIN VREF VSS VAIN VREF Average current consumption when A/D is on(Note 1) During VAIN acquisition. Based on differential of VHOLD to VAIN to charge CHOLD See the "8-bit A/D Converter" section During A/D Conversion cycle Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. VREF current is from RA3 pin or VDD pin, whichever is selected as reference input. DS31030A-page 30-34 1997 Microchip Technology Inc. Section 30. Electrical Specifications Figure 30-19: Example 8-bit A/D Conversion Timing Waveforms BSF ADCON0, GO 1 TCY (TOSC/2) (1) 131 Q4 130 132 A/D CLK 7 A/D DATA 6 5 4 3 2 1 NEW_DATA OLD_DATA ADRES 0 ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. Table 30-31: Example 8-bit A/D Conversion Requirements Param Symbol Characteristic No. 130 TAD Min Typ Max Units Conditions 1.6 -- -- s TOSC based, VREF 3.0V PIC16LCXXX 2.0 -- -- s TOSC based, VREF full range PIC16CXXX 2.0 4.0 6.0 s A/D RC Mode PIC16LCXXX 3.0 6.0 9.0 s A/D RC Mode 11 -- 11 TAD Note 2 20 -- s 5 -- -- s The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). A/D clock period PIC16CXXX 131 TCNV Conversion time (not including S/H time) (Note 1) 132 TACQ Acquisition time 134 TGO Q4 to A/D clock start -- 2TOSC -- -- If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 136 TAMP Amplifier settling time (Note 2) 1 -- -- s This may be used if the "new" input voltage has not changed by more than 1LSb (i.e. 5 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). TSWC Switching Time from convert sample 1 -- 1 TAD Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This specification ensured by design. Note 1: ADRES register may be read on the following TCY cycle. See the "8-bit A/D Converter" section for minimum requirements. 1997 Microchip Technology Inc. DS31030A-page 30-35 Electrical Specifications 135 30 PICmicro MID-RANGE MCU FAMILY 30.24 Example 10-bit A/D Timing Waveforms and Requirements Table 30-32: Example 10-bit A/D Converter Characteristics Param Symbol Characteristic No. Min Typ Max Units Conditions Resolution -- -- 10 bit Absolute error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A01 NR A02 EABS A03 EIL Integral linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A04 EDL Differential linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A05 EFS Full scale error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A06 EOFF Offset error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A10 -- Monotonicity -- guaranteed -- A20 VREF Reference voltage (VREFH - VREFL) 0V -- -- V For no latch-up 3V -- -- V For 10-bit resolution AVDD + 0.3V V A20A -- A21 VREFH Reference voltage High AVSS -- A22 VREFL Reference voltage Low AVSS - 0.3V -- AVDD V A25 VAIN Analog input voltage AVSS - 0.3V -- VREF + 0.3V V A30 ZAIN Recommended impedance of analog voltage source -- -- 10.0 k A40 IAD A/D conversion PIC16CXXX current (VDD) PIC16LCXXX -- 180 -- A -- 90 -- A VREF input current (Note 2) 10 -- 1000 A -- -- 10 A A50 IREF VREF = VDD = 5.12V, VSS VAIN VREF VSS VAIN VREF Average current consumption when A/D is on. (Note 1) During VAIN acquisition. Based on differential of VHOLD to VAIN. To charge CHOLD see the "10-bit A/D Converter" section. During A/D conversion cycle Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. VREF current is from RG0 and RG1 pins or AVDD and AVSS pins, whichever is selected as reference input. DS31030A-page 30-36 1997 Microchip Technology Inc. Section 30. Electrical Specifications Figure 30-20: Example 10-bit A/D Conversion Timing Waveforms BSF ADCON0, GO Note 2 131 Q4 130 A/D CLK 132 9 A/D DATA 8 7 ... ... 2 1 0 NEW_DATA OLD_DATA ADRES TCY ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 2: This is a minimal RC delay (typically 100 nS), which also disconnects the holding capacitor from the analog input. Table 30-33: Example 10-bit A/D Conversion Requirements Param Symbol Characteristic No. 130 TAD A/D clock period Min Typ Max Units Conditions PIC16CXXX 1.6 -- -- s TOSC based, VREF 3.0V PIC16LCXXX 3.0 -- -- s TOSC based, VREF full range PIC16CXXX 2.0 4.0 6.0 s A/D RC Mode PIC16LCXXX 3.0 6.0 9.0 s A/D RC Mode 11 -- 12 TAD 131 TCNV Conversion time (not including acquisition time) (Note 1) 132 TACQ Acquisition time (Note 3) 15 10 -- -- -- -- s s -40C Temp 125C 0C Temp 125C 136 TAMP Amplifier settling time (Note 2) 1 -- -- s This may be used if the "new" input voltage has not changed by more than 1LSb (i.e. 5 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). 135 TSWC Switching Time from convert sample -- -- Note 4 Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This specification ensured by design. 1997 Microchip Technology Inc. DS31030A-page 30-37 30 Electrical Specifications Note 1: ADRES register may be read on the following TCY cycle. 2: See the "10-bit A/D Converter" section for minimum conditions when input voltage has changed more than 1 LSb. 3: The time for the holding capacitor to acquire the "New" input voltage when the voltage changes full scale after the conversion (AVDD to AVSS, or AVSS to AVDD). The source impedance (RS) on the input channels is 50 . 4: On the next Q4 cycle of the device clock PICmicro MID-RANGE MCU FAMILY 30.25 Example Slope A/D Timing Waveforms and Requirements Figure 30-21: CAPTURE CLK Example Slope A/D Conversion Cycle ADTMR INCREMENTS ADRST ADCON0<1> ADTMR COUNT XX XX+1 XX+2 XX+3 COMPARE CDAC ADCIF Capture Register DS31030A-page 30-38 XX+8 XX+9 (must be cleared by software) XX XX+8 1997 Microchip Technology Inc. Section 30. Electrical Specifications Table 30-34: Example Slope A/D Component Characteristics DC CHARACTERISTICS Param Symbol No. A100 VAIN A101 A102 A103 A104 140 141 Characteristic Slope A/D Comparator Analog Input Voltage Range Input Offset Voltage Differential Voltage Gain (Note 1) CMRR Common Mode Rejection Ratio (Note 1) RRadc Power Supply Rejection Ratio (Note 1) TSET Turn-on Settling Time Band Gap Reference (to < 0.1% (Note 1) Programmable Current Source (to < 0.1%) GDV 141A Min Typ Max Units Conditions VSS -- VDD -1.4 V -10 2 10 mV -- 100 -- dB -- 80 -- dB -- 70 -- dB -- 1 10 ms -- 1 10 ms -- 1 10 s -- -- -- -- -- -- -- +50 -50 +20 -20 +0.1 -0.1 20 -- -- -- -- -- -- -- -- -- 0.01 0.02 -- -- -- -- 0.04 0.2 -- -- %/V %/V From VDDmin to VDDmax From VDDmin to VDDmax -- %/V From VDDmin to VDDmax 3.25 +1/2 A LSb 1 LSb CDAC = 0V Measured over common-mode range VDD = 5V, TA = 25C, over common-mode range TA = 25C, VDDmin VDD VDDmax REFOFF bit in SLPCON register 1 0 Bias generator (reference) turn-on time (REFOFF 1 0) (reference start-up) (Note 1) REFOFF = 0 (constant), ADCON1<7:4> 0000b 1111b (reference already on and stable) (Note 3) TC A110 Temperature Coefficient (Note 1) TCBGR Band Gap Reference Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial, -40C TA +85C for industrial and -40C TA +125C for extended Operating voltage VDD range as described in DC spec Table 30-3. A110A A111 A112 A120 A121 A130 A131 A132 1997 Microchip Technology Inc. -- 1.25 -1/2 2.25 30 Electrical Specifications A140 A141 TCPCS Programmable Current Source TCkref Slope Reference Divider CA Calibration Accuracy (Note3, 5) CABGR Band Gap Reference CASRV Slope Reference Divider SN Supply Sensitivity (Note 1) SNBGR Band Gap Reference SNPCS Programmable Current Source SNkref Slope Reference Divider Programmable Current Source IRES Resolution EIL Relative accuracy (linearity error) ppm/C -40C TA +25C 25C TA +85C ppm/C 0C TA +25C 25C TA +70C %/C -40C TA +25C 25C TA +85C ppm/C -40C TA +85C All parameters calibrated at VDD = 5V and TA = +25C % % DS31030A-page 30-39 PICmicro MID-RANGE MCU FAMILY 30.26 Example LCD Timing Waveforms and Requirements Figure 30-22: Example LCD Voltage Waveform 201 202 VLCD3 VLCD2 VLCD1 VSS Table 30-35: Example LCD Module Timing Requirements Param Symbol Characteristic No. Min Typ Max Units Conditions 200 FLCDRC LCDRC Oscillator Frequency -- 14 22 kHz VDD = 5V, -40C to +85C 201 TrLCD Output Rise Time -- -- 200 s COM outputs Cload = 5,000 pF SEG outputs Cload = 500 pF VDD = 5.0V, T = 25C 202 TfLCD Output Fall Time (Note 1) TrLCD 0.05TrLCD -- TrLCD + 0.05TrLCD s COM outputs Cload = 5,000 pF SEG outputs Cload = 500 pF VDD = 5.0V, T = 25C Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: 0 source impedance at VLCD. DS31030A-page 30-40 1997 Microchip Technology Inc. Section 30. Electrical Specifications 30.27 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or High-End families), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to the Electrical Specifications are: Title Application Note # No related Application Notes 30 Electrical Specifications 1997 Microchip Technology Inc. DS31030A-page 30-41 PICmicro MID-RANGE MCU FAMILY 30.28 Revision History Revision A This is the initial released revision of the Electrical Specifications description. DS31030A-page 30-42 1997 Microchip Technology Inc. M 31 Device Characteristics Section 31. Device Characteristics HIGHLIGHTS 31.1 31.2 31.3 31.4 Introduction ..................................................................................................................31-2 Characterization vs. Electrical Specification ................................................................31-2 DC and AC Characteristics Graphs and Tables ...........................................................31-2 Revision History .........................................................................................................31-22 1997 Microchip Technology Inc. DS31031A page 31-1 PICmicro MID-RANGE MCU FAMILY 31.1 Introduction Microchip Technology Inc. provides characterization information on the devices that it manufactures. This information becomes available after the devices have undergone a complete characterization and the data has been analyzed. This data is taken on both device testers and on bench setups. The characterization data gives the designer a better understanding of the device characteristics, to better judge the acceptability of the device to the application. 31.2 Characterization vs. Electrical Specification The difference between this information and the Electrical specifications can be classified as what the user should expect the devices to do vs. what Microchip tests the devices to. The characterization graphs and tables provided are for design guidance and are not tested or guaranteed. There may be differences between what the characterization shows as the limits vs. that which is tested, as shown in the Electrical Specification section. This results from capabilities of the production tester equipment, plus whatever guard band that may be necessary. 31.3 DC and AC Characteristics Graphs and Tables Each table gives specific information that may be useful design information. These values are taken under fixed circumstances. Measurements taken in your application may not lead to the same values if your circumstances are not the same. In some graphs or tables the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices will operate properly only within the specified range. Note: DS31031A-page 31-2 The data presented in the device Data Sheet Characterization section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at, 25C, while 'max' or 'min' represents (mean +3) and (mean -3) respectively where is standard deviation. 1997 Microchip Technology Inc. Section 31. Device Characteristics 31.3.1 31 IPD vs. VDD The characterization shows graphs for both the Watchdog Timer (WDT) disabled and enabled. This is required since the WDT requires an on-chip RC oscillator which consumes additional current. Since the device may have certain features and modules that can operate while the device is in sleep mode. Some of these modules are: * * * * * * * Watchdog Timer (WDT) Brown-out Reset (BOR) circuitry Timer1 Analog to Digital converter LCD module Comparators Voltage Reference If these features are operating while the device is in sleep mode, a higher current will be consumed. When all features are disabled, the device will consume the lowest possible current (the leakage current). If more then one feature is enabled then the expected current can easily be calculated as the base current (everything disabled and in sleep mode) plus all delta currents. Example 31-1 shows an example of calculating the typical currents for a device at 5V, with the WDT and Timer1 oscillator enabled. Example 31-1:IPD Calculations with WDT and TIMER1 Oscillator Enabled (@ 5V) Base Current WDT Delta Current Timer1 Delta Current Total Sleep Current 1997 Microchip Technology Inc. 14 nA 14 A 22 A 36 A ; Device leakage current ; 14 A - 14 nA = 14 A ; 22 A - 14 nA = 22 A ; DS31031A-page 31-3 Device Characteristics IPD is the current (I) that the device consumes when the device is in sleep mode (power-down), referred to as power-down current. These tests are taken with all I/O as inputs, either pulled high or low. That is, there are no floating inputs, nor are any pins driving an output (with a load). PICmicro MID-RANGE MCU FAMILY Figure 31-1: Example Typical IPD vs. VDD (WDT Disabled, RC Mode) 35 30 IPD (nA) 25 20 15 10 5 0 2.5 Figure 31-2: 3.0 3.5 4.0 4.5 VDD (Volts) 5.0 5.5 6.0 Example Maximum IPD vs. VDD (WDT Disabled, RC Mode) 10.000 85C 70C IPD (A) 1.000 25C 0.100 0C -40C 0.010 0.001 2.5 DS31031A-page 31-4 3.0 3.5 4.0 4.5 VDD (Volts) 5.0 5.5 6.0 1997 Microchip Technology Inc. Section 31. Device Characteristics Figure 31-3: 31 Example Typical IPD vs. VDD @ 25C (WDT Enabled, RC Mode) Device Characteristics 25 IPD (A) 20 15 10 5 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Figure 31-4: Example Maximum IPD vs. VDD (WDT Enabled, RC Mode) 35 -40C 30 0C IPD (A) 25 20 70C 15 85C 10 5 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) 1997 Microchip Technology Inc. DS31031A-page 31-5 PICmicro MID-RANGE MCU FAMILY Figure 31-5: Example Typical IPD vs. VDD Brown-out Detect Enabled (RC Mode) 1400 1200 IPD (A) 1000 Device NOT in Brown-out Reset 800 600 400 200 0 2.5 Device in Brown-out Reset 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) The shaded region represents the built-in hysteresis of the brown-out reset circuitry. Figure 31-6: Example Maximum IPD vs. VDD Brown-out Detect Enabled (85C to -40C, RC Mode) 1600 1400 1200 IPD (A) 1000 Device NOT in Brown-out Reset 800 600 400 Device in Brown-out Reset 200 4.3 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) The shaded region represents the built-in hysteresis of the Brown-out Reset circuitry. DS31031A-page 31-6 1997 Microchip Technology Inc. Section 31. Device Characteristics Figure 31-7: 31 Example Typical IPD vs. Timer1 Enabled (32 kHz, RC0/RC1 = 33 pF/33 pF, RC Mode) Device Characteristics 30 25 IPD (A) 20 15 10 5 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Figure 31-8: Example Maximum IPD vs. Timer1 Enabled (32 kHz, RC0/RC1 = 33 pF/33 pF, 85C to -40C, RC Mode) 45 40 35 IPD (A) 30 25 20 15 10 5 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) 1997 Microchip Technology Inc. DS31031A-page 31-7 PICmicro MID-RANGE MCU FAMILY 31.3.2 IDD vs. Frequency IDD is the current (I) that the device consumes when the device is in operating mode. This test is taken with all I/O as inputs, either pulled high or low. That is, there are no floating inputs, nor are any pins driving an output (with a load). The IDD vs. Frequency charts measure the results on a Microchip automated bench setup, called the DCS (Data Collection System). The DCS accurately reflects the device and specified component values, that is, it does not add stray capacitance or current. 31.3.2.1 RC Measurements For the RC measurement, the DCS selects a resistor and capacitor value, and then varies the voltage over the specified range. As the voltage is changed, the frequency of operation changes. For a fixed RC, as VDD increases, the frequency increases. After the measurement, at this RC, has been taken, the RC value is changed and the measurements are taken again. Each point on the graph corresponds to a device voltage, resistor value (R), and capacitor value (C). Figure 31-9: Example Typical IDD vs. Frequency (RC Mode @ 22 pF, 25C) 2000 6.0V 1800 5.5V 1600 5.0V 4.5V IDD (A) 1400 4.0V 1200 3.5V 1000 3.0V 800 2.5V 600 400 200 0 0.0 0.5 1.0 1.5 2.0 2.5 Frequency (MHz) R = 10 k R = 5 k DS31031A-page 31-8 3.0 3.5 4.0 4.5 Shaded area is beyond recommended range 1997 Microchip Technology Inc. Section 31. Device Characteristics Figure 31-10: 31 Example Maximum IDD vs. Frequency (RC Mode @ 22 pF, -40C to 85C) 6.0V 1800 5.5V 5.0V 1600 4.5V IDD (A) 1400 4.0V 1200 3.5V 1000 3.0V 800 2.5V 600 400 200 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (MHz) Figure 31-11: 3.5 4.0 4.5 Shaded area is beyond recommended range Example Typical IDD vs. Frequency (RC Mode @ 100 pF, 25C) 1600 6.0V 1400 5.5V 5.0V 1200 4.5V 4.0V 1000 IDD (A) 3.5V 3.0V 800 2.5V 600 400 200 0 0 200 400 Shaded area is beyond recommended range 1997 Microchip Technology Inc. 600 800 1000 1200 1400 1600 1800 Frequency (kHz) DS31031A-page 31-9 Device Characteristics 2000 PICmicro MID-RANGE MCU FAMILY Figure 31-12: Example Maximum IDD vs. Frequency (RC Mode @ 100 pF, -40C to 85C) 1600 6.0V 1400 5.5V 5.0V 1200 4.5V 4.0V 1000 IDD (A) 3.5V 3.0V 800 2.5V 600 400 200 0 0 200 400 600 800 1000 1200 1400 1600 1800 Frequency (kHz) Shaded area is beyond recommended range Figure 31-13: Example Typical IDD vs. Frequency (RC Mode @ 300 pF, 25C) 1200 6.0V 5.5V 1000 5.0V 4.5V 4.0V 800 IDD (A) 3.5V 3.0V 600 2.5V 400 200 0 0 100 200 300 400 500 600 700 Frequency (kHz) DS31031A-page 31-10 1997 Microchip Technology Inc. Section 31. Device Characteristics 31 Figure 31-14: Example Maximum IDD vs. Frequency (RC Mode @ 300 pF, -40C to 85C) 6.0V 5.5V 1000 5.0V 4.5V 4.0V 800 3.5V IDD (A) 3.0V 600 2.5V 400 200 0 0 100 200 300 400 500 600 700 Frequency (kHz) Figure 31-15: Example Typical IDD vs. Capacitance @ 500 kHz (RC Mode) 600 5.0V 500 4.0V IDD (A) 400 3.0V 300 200 100 0 20 pF 100 pF 300 pF Capacitance (pF) 1997 Microchip Technology Inc. DS31031A-page 31-11 Device Characteristics 1200 PICmicro MID-RANGE MCU FAMILY 31.3.2.2 Crystal Oscillator Measurements On the Data Collection System, there are several crystals. For this test a crystal is multiplexed into the device circuit, and the crystal's capacitance values can be varied. The capacitance and voltage values are varied to determine the best characteristics (current, oscillator waveform, and oscillator start-up), and then the currents are measured over voltage. The next crystal oscillator is then switched in and the procedure is repeated. Figure 31-16: Example Typical IDD vs. Frequency (LP Mode, 25C) 120 100 IDD (A) 80 60 6.0V 5.5V 5.0V 4.5V 4.0V 3.5V 3.0V 2.5V 40 20 0 0 50 100 150 200 Frequency (kHz) Figure 31-17: Example Maximum IDD vs. Frequency (LP Mode, 85C to -40C) 140 120 IDD (A) 100 80 6.0V 5.5V 5.0V 4.5V 4.0V 3.5V 3.0V 2.5V 60 40 20 0 0 50 100 150 200 Frequency (kHz) DS31031A-page 31-12 1997 Microchip Technology Inc. Section 31. Device Characteristics 31 Figure 31-18: Example Typical IDD vs. Frequency (XT Mode, 25C) 1600 6.0V 5.5V 1400 5.0V 1200 4.5V 1000 4.0V 3.5V IDD (A) 800 3.0V 600 2.5V 400 200 0 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 Frequency (MHz) Figure 31-19: Example Maximum IDD vs. Frequency (XT Mode, -40C to 85C) 1800 6.0V 1600 5.5V 1400 5.0V IDD (A) 1200 4.5V 1000 4.0V 800 3.5V 3.0V 600 2.5V 400 200 0 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 Frequency (MHz) 1997 Microchip Technology Inc. DS31031A-page 31-13 Device Characteristics 1800 PICmicro MID-RANGE MCU FAMILY Figure 31-20: Example Typical IDD vs. Frequency (HS Mode, 25C) 7.0 6.0 IDD (mA) 5.0 4.0 3.0 6.0V 5.5V 5.0V 4.5V 4.0V 2.0 1.0 0.0 1 2 4 6 8 10 12 14 16 18 20 14 16 18 20 Frequency (MHz) Figure 31-21: Example Maximum IDD vs. Frequency (HS Mode, -40C to 85C) 7.0 6.0 IDD (mA) 5.0 4.0 3.0 6.0V 5.5V 5.0V 4.5V 4.0V 2.0 1.0 0.0 1 2 4 6 8 10 12 Frequency (MHz) DS31031A-page 31-14 1997 Microchip Technology Inc. Section 31. Device Characteristics 31.3.3 31 RC Oscillator Frequency Figure 31-22: Example Typical RC Oscillator Frequency vs. VDD CEXT = 22 pF, T = 25C 6.0 5.5 5.0 Fosc (MHz) 4.5 R = 5k 4.0 3.5 3.0 R = 10k 2.5 2.0 1.5 1.0 R = 100k 0.5 0.0 2.5 3.0 3.5 4.0 4.5 VDD (Volts) 5.0 5.5 6.0 Shaded area is beyond recommended range. Figure 31-23: Example Typical RC Oscillator Frequency vs. VDD CEXT = 100 pF, T = 25C 2.4 2.2 R = 3.3k 2.0 1.8 Fosc (MHz) 1.6 R = 5k 1.4 1.2 1.0 R = 10k 0.8 0.6 0.4 R = 100k 0.2 0.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) 1997 Microchip Technology Inc. DS31031A-page 31-15 Device Characteristics These tables show the effects of the RC oscillator frequency as the device voltage varies. In these measurements a capacitor and resistor value are selected and then the frequency of the RC is measured as the device voltage varies. The table shows the typical frequency for a R and C value at 5V, as well as the variation from this frequency that can be expected due to device processing. PICmicro MID-RANGE MCU FAMILY Figure 31-24: Example Typical RC Oscillator Frequency vs. VDD CEXT = 300 pF, T = 25C 1000 900 800 R = 3.3k Fosc (kHz) 700 600 R = 5k 500 400 R = 10k 300 200 R = 100k 100 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Table 31-1: Example RC Oscillator Frequencies Average CEXT REXT Fosc @ 5V, 25C 22 pF 100 pF 300 pF 5k 4.12 MHz 1.4% 10k 2.35 MHz 1.4% 100k 268 kHz 1.1% 3.3k 1.80 MHz 1.0% 5k 1.27 MHz 1.0% 10k 688 kHz 1.2% 100k 77.2 kHz 1.0% 3.3k 707 kHz 1.4% 5k 501 kHz 1.2% 10k 269 kHz 1.6% 100k 28.3 kHz 1.1% The percentage variation indicated here is part to part variation due to normal process distribution. The variation indicated is 3 standard deviation from average value for VDD = 5V. DS31031A-page 31-16 1997 Microchip Technology Inc. Section 31. Device Characteristics 31.3.4 31 Oscillator Transconductance Figure 31-25: Example Transconductance (gm) of HS Oscillator vs. VDD 4.0 Max -40C 3.5 3.0 gm (mA/V) 2.5 Typ 25C 2.0 Min 85C 1.5 1.0 0.5 0.0 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 VDD (Volts) Shaded area is beyond recommended range Figure 31-26: Example Transconductance (gm) of LP Oscillator vs. VDD 110 100 Max -40C 90 gm (mA/V) 80 70 60 Typ 25C 50 40 30 20 Min 85C 10 0 2.0 2.5 3.0 Shaded areas are beyond recommended range 1997 Microchip Technology Inc. 3.5 4.0 4.5 5.0 VDD (Volts) 5.5 6.0 6.5 7.0 DS31031A-page 31-17 Device Characteristics Transconductance of the oscillator indicates the gain of the oscillator. As the transconductance increases, the gain of the oscillator circuit increases which causes the current consumption of the oscillator circuit to increase. Also as the transconductance increases the maximum frequency that the oscillator circuit can support also increases, or the start-up time of the oscillator decreases. PICmicro MID-RANGE MCU FAMILY Figure 31-27: Example Transconductance (gm) of XT Oscillator vs. VDD 1000 900 Max -40C 800 gm (mA/V) 700 600 Typ 25C 500 400 Min 85C 300 200 100 0 2.0 2.5 Shaded areas are 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 VDD (Volts) beyond recommended range DS31031A-page 31-18 1997 Microchip Technology Inc. Section 31. Device Characteristics 31.3.5 31 Crystal Start-up Time Figure 31-28: Example Typical XTAL Start-up Time vs. VDD (LP Mode, 25C) 3.5 Start-up Time (Seconds) 3.0 2.5 2.0 32 kHz, 33 pF/33 pF 1.5 1.0 0.5 200 kHz, 15 pF/15 pF 0.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Figure 31-29: Example Typical XTAL Start-up Time vs. VDD (HS Mode, 25C) 7 Start-up Time (ms) 6 20 MHz, 33 pF/33 pF 5 4 8 MHz, 33 pF/33 pF 3 20 MHz, 15 pF/15 pF 8 MHz, 15 pF/15 pF 2 1 4.0 4.5 5.0 5.5 6.0 VDD (Volts) 1997 Microchip Technology Inc. DS31031A-page 31-19 Device Characteristics These graphs show the start-up time that one should expect to see at the specified voltage level, for a given crystal/capacitor combination. PICmicro MID-RANGE MCU FAMILY Figure 31-30: Example Typical XTAL Start-up Time vs. VDD (XT Mode, 25C) 70 60 Start-up Time (ms) 50 40 200 kHz, 68 pF/68 pF 30 200 kHz, 47 pF/47 pF 20 1 MHz, 15 pF/15 pF 10 4 MHz, 15 pF/15 pF 0 2.5 DS31031A-page 31-20 3.0 3.5 4.0 4.5 VDD (Volts) 5.0 5.5 6.0 1997 Microchip Technology Inc. Section 31. Device Characteristics 31.3.6 31 Tested Crystals and Their Capacitor Values Table 31-2: Example Capacitor Selection for Crystal Oscillators Osc Type Crystal Frequency LP XT Capacitor Range C2 32 kHz 33 pF 200 kHz 15 pF 15 pF 200 kHz 47-68 pF 47-68 pF 1 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 8 MHz 15-33 pF 15-33 pF 20 MHz 15-33 pF 15-33 pF HS Note: Capacitor Range C1 33 pF Higher capacitance increases the stability of the oscillator but also increases the start-up time. These values are for design guidance only. Rs may be required in HS mode as well as XT mode to avoid overdriving crystals with low drive level specification. Since each crystal has its own characteristics, the user should consult the crystal manufacturer for appropriate values of external components or verify oscillator performance. Crystals Used: 31.3.7 32 kHz Epson C-001R32.768K-A 20 PPM 200 kHz STD XTL 200.000KHz 20 PPM 1 MHz ECS ECS-10-13-1 50 PPM 4 MHz ECS ECS-40-20-1 50 PPM 8 MHz EPSON CA-301 8.000M-C 30 PPM 20 MHz EPSON CA-301 20.000M-C 30 PPM Example EPROM Memory Erase Times The UV erase time of an EPROM cell depends on the geometry size of the EPROM cell and the manufacturing technology. Table 31-3 shows some of the expected erase times for each different device. Table 31-3: Example of Typical EPROM Erase Time Recommendations Example Device Wavelength (Angstroms) Intensity (W/cm2) Distance from UV lamp (inches) 1 2537 12,000 1 2 2537 12,000 1 3 2537 12,000 1 4 2537 12,000 1 Note 1: If these criteria are not met, the erase times will be different. Table 31-4: 1997 Microchip Technology Inc. Typical Time (1) (minutes) 15 - 20 20 40 60 Refer to the device data sheet for the typical erase times for a device. DS31031A-page 31-21 Device Characteristics This table shows the crystal frequency and manufacturer that was used for every tests in this section, as well as the capacitor values/ranges that exhibited the best characteristics. PICmicro MID-RANGE MCU FAMILY 31.4 Revision History Revision A This is the initial released revision of the Device Characteristics description. DS31031A-page 31-22 1997 Microchip Technology Inc. M Section 32. Development Tools HIGHLIGHTS This section of the manual contains the following major topics: 32 1997 Microchip Technology Inc. DS31032A page 32-1 Development Tools 32.1 Introduction ..................................................................................................................32-2 32.2 The Integrated Development Environment (IDE) .........................................................32-3 32.3 MPLAB Software Language Support ...........................................................................32-6 32.4 MPLAB-SIM Simulator Software ..................................................................................32-8 32.5 MPLAB Emulator Hardware Support ...........................................................................32-9 32.6 MPLAB Programmer Support ....................................................................................32-10 32.7 Supplemental Tools....................................................................................................32-11 32.8 Development Boards..................................................................................................32-12 32.9 Development Tools for Other Microchip Products ......................................................32-14 32.10 Related Application Notes..........................................................................................32-15 32.11 Revision History .........................................................................................................32-16 PICmicro MID-RANGE MCU FAMILY 32.1 Introduction Microchip offers a wide range of tightly integrated development tools to ease the application development process. These can be broken down into the core development tools and the supplemental tools. The core tools are as follows: * MPLAB Integrated Development Environment, including full featured editor * Language Products - MPASM Assembler - MPLAB-C C Compiler * MPLAB-SIM Software Simulator * Real-Time In-Circuit Emulators - PICMASTER/PICMASTER CE Emulator with Full Featured Trace and Breakpoint debug capabilities - ICEPIC Low-Cost Emulator with Breakpoint debug capabilities * Device Programmers - PRO MATE II Universal Programmer - PICSTART Plus Entry-Level Prototype Programmer Supplemental Tools: * Other Software Programming Tools - fuzzyTECH-MP Fuzzy logic development system - MP-Driveway Application Code Generator * Development Boards - PICDEM-1 Low-Cost Demonstration Board - PICDEM-2 Low-Cost Demonstration Board - PICDEM-3 Low-Cost Demonstration Board - PICDEM-14A Low-Cost Demonstration Board The minimum configuration of MPLAB, is the Integrated Development Environment (IDE), the assembler (MPASM), and the software simulator (MPLAB-SIM). Other tools are added to MPLAB as they are installed. This gives a common platform for the design activity, from the writing and assembling of the source code, through the simulation/emulation, to the programming of prototype devices. Note: The most current version may be downloaded from Microchip's web site or BBS for free. In addition to Microchip, there are many third party vendors. Microchip's Third Party Handbook gives an overview of the manufactures and their tools. DS31032A-page 32-2 1997 Microchip Technology Inc. Section 32. Development Tools 32.2 The Integrated Development Environment (IDE) The core set of development tools operate under the IDE umbrella, called MPLAB. This gives a consistent look and feel to all the development tools so that minimal learning of the new tool interface is required. The MPLAB IDE integrates all the following aspects of development: * * * * * * Source code editing Project management Machine code generation (from assembly or "C") Device simulation Device emulation Device programming MPLAB is a PC based Windows(R) 3.x application. It has been extensively tested using Windows 95 and recommended in either of these operating environments. Windows is a registered trademark of Microsoft Corporation. 1997 Microchip Technology Inc. DS31032A-page 32-3 Development Tools This comprehensive tool suite allows the complete development of a project without leaving the MPLAB environment. 32 PICmicro MID-RANGE MCU FAMILY 32.2.1 MPLAB The MPLAB IDE Software brings an ease of software development previously unseen in the 8-bit microcontroller market. MPLAB is a Windows based application that contains: * A full featured editor * Three operating modes - editor - emulator - simulator * A project manager * Customizable tool bar and key mapping * A status bar with project information * Extensive on-line help MPLAB allows you to: * Edit your source files. This includes: - MPASM assembly language - MPLAB-C `C' language * One touch assemble (or compile) and download to PIC16/17 tools (automatically updates all project information) * Debug using: - source files - absolute listing file - program memory * Run up to four emulators on the same PC * Run or Single-step - program memory - source file - absolute listing Microchip's simulator, MPLAB-SIM, operates under the same platform as the PICMASTER emulator. This allows the user to learn a single tool set which functions equivalently for both the simulator and the full featured emulator. DS31032A-page 32-4 1997 Microchip Technology Inc. Section 32. Development Tools Figure 32-1 shows a typical MPLAB desktop in the middle of a project. Some of the highlights are: * Tool bars, multiple choices and user configurable * Status, mode information, and button help on footer bar * Multiple windows, such as - Source code - Source listing (most useful for `C' programs) - Register file window (RAM) - Watch windows (to look at specific register) - Stop watch window for time/cycle calculations * Programmer support (in this case PRO MATE pull down menu) Figure 32-1: 32 MPLAB Project Window Development Tools 1997 Microchip Technology Inc. DS31032A-page 32-5 PICmicro MID-RANGE MCU FAMILY 32.3 MPLAB Software Language Support To make the device operate as desired in the application, a software program needs to be written for the microcontroller. This software program needs to be written in one of the programming languages for the device. Currently MPLAB supports two of Microchip's language products: * Microchip Assembler (MPASM) * Microchip `C' Compiler (MPLAB-C) * Other language products that support Common Object Description (COD) may also work with MPLAB 32.3.1 Assembler (MPASM) The MPASM Universal Macro Assembler is a PC-hosted symbolic assembler. It supports all Microchip microcontroller families. MPASM offers full featured Macro capabilities, conditional assembly, and several source and listing formats. It generates various object code formats to support Microchip's development tools as well as third party programmers. MPASM allow full symbolic debugging from the Microchip Universal Emulator System (PICMASTER). MPASM has the following features to assist in developing software for specific use applications. * Provides translation of Assembler source code to object code for all Microchip microcontrollers. * Macro assembly capability. * Produces all the files (Object, Listing, Symbol, and special) required for symbolic debug with Microchip's emulator systems. * Supports Hex (default), Decimal and Octal source and listing formats. MPASM provides a rich directive language to support programming of the PICmicro. Directives are helpful in making the development of your assemble source code shorter and more maintainable. 32.3.2 C Compiler (MPLAB-C) The MPLAB-C is a complete `C' compiler for Microchip's PICmicro family of microcontrollers. The compiler provides powerful integration capabilities and ease of use not found with other compilers. For easier source level debugging, the compiler provides symbol information that is compatible with the MPLAB IDE memory display, Watch windows, and File register windows. DS31032A-page 32-6 1997 Microchip Technology Inc. Section 32. Development Tools 32.3.3 MPLINK Linker MPLINK is a linker for the Microchip C compiler, MPLAB-C, and the Microchip relocatable assembler, MPASM. MPLINK is introduced with MPLAB-C v2.00 and can only be used with these or later versions. MPLINK allows you to produce modular, re-usable code with MPLAB-C and MPASM. Control over the linking process is accomplished through a linker "script" file and with command line options. MPLINK ensures that all symbolic references are resolved and that code and data fit into the available PICmicro device. MPLINK combines multiple input object modules generated by MPLAB-C or MPASM, into a single executable file. The actual addresses of data and the location of functions will be assigned when MPLINK is executed. This means that you will instruct MPLINK to place code and data somewhere within the named regions of memory, not to specific physical locations. MPLINK also provides flexibility for specifying that certain blocks of data memory are re-usable, so that different routines (which never call each other and don't depend on this data to be retained between execution) can share limited RAM space. 32.3.4 MPLIB Librarian MPLIB is a librarian for use with COFF object modules created using either MPASM v2.0, MPASMWIN v2.0, or MPLAB-C v2.0 or later. MPLIB manages the creation and modification of library files. A library file is a collection of object modules that are stored in a single file. There are several reasons for creating library files: * Libraries make linking easier. Since library files can contain many object files, the name of a library file can be used instead of the names of many separate object when linking. * Libraries help keep code small. Since a linker only uses the required object files contained in a library, not all object files which are contained in the library necessarily wind up in the linker's output module. * Libraries make projects more maintainable. If a library is included in a project, the addition or removal of calls to that library will not require a change to the link process. * Libraries help convey the purpose of a group of object modules. Since libraries can group together several related object modules, the purpose of a library file is usually more understandable that the purpose of its individual object modules. For example, the purpose of a file named "math.lib" is more apparent that the purpose of 'power.o', 'ceiling.o', and 'floor.o'. 1997 Microchip Technology Inc. DS31032A-page 32-7 Development Tools Once the linker knows about the ROM and RAM memory regions available in the target PICmicro device and it analyzes all the input files, it will try to fit the application's routines into ROM and assign it's data variables into available RAM. If there is too much code or too many variables to fit, MPLINK will give an error message. 32 PICmicro MID-RANGE MCU FAMILY 32.4 MPLAB-SIM Simulator Software The software simulator is a no-cost tool with which to evaluate Microchip's products and designs. The use of the simulator greatly helps debug software, particularly algorithms. Depending on the complexity of a design project a time/cost benefit should be looked at comparing the simulator with an emulator. For projects that have multiple engineers in the development, the simulator in conjunction with an emulator can keep costs down and will allow speedy debug of the tough problems. MPLAB-SIM Simulator simulates the PICmicro series microcontrollers on an instruction level. On any given instruction, the user may examine or modify any of the data areas or provide external stimulus to any of the pins. The input/output radix can be set by the user and the execution can be performed in; single step, execute until break, or in a trace mode. MPLAB-SIM supports symbolic debugging using MPLAB-C, and MPASM. The Software Simulator offers the low cost flexibility to develop and debug code outside of the laboratory environment making it an excellent multi-project software development tool. DS31032A-page 32-8 1997 Microchip Technology Inc. Section 32. Development Tools 32.5 MPLAB Emulator Hardware Support Microchip offers two emulators, a high-end version (PICMASTER) and a low-cost version (ICEPIC). Both versions offer a very good price/feature value, and the selection of which emulator should depend on the feature set that you wish. For people looking at doing several projects with Microchip devices (or using the high-end devices) the use of PICMASTER may offset the additional investment, through time savings achieved with the sophisticated breakpoint and trace capabilities. 32.5.1 PICMASTER: High Performance Universal In-Circuit Emulator The PICMASTER Universal In-Circuit Emulator provides the product development engineer with a complete microcontroller design tool set for all microcontrollers in the Baseline, Mid-Range, and High End families. PICMASTER operates in the MPLAB Integrated Development Environment (IDE), which allows editing, "make" and download, and source debugging from a single environment. The PICMASTER Emulator System has been designed as a real-time emulation system with advanced features that are generally found on more expensive development tools. A CE compliant version of PICMASTER is available for European Union (EU) countries. 32.5.2 ICEPIC: Low-Cost PIC16CXXX In-Circuit Emulator ICEPIC is a low-cost in-circuit emulator solution for the Microchip Base-line and Mid-Range families of 8-bit OTP microcontrollers. ICEPIC user interface operates on PC-compatible machines ranging from 286-AT through Pentium based machines under Windows 3.x environment. ICEPIC features real-time emulation. ICEPIC is available under the MPLAB environment. ICEPIC is designed by Neosoft Inc. and is manufactured under license by RF Solutions. Other emulator solutions may be available directly from RF solutions. 1997 Microchip Technology Inc. DS31032A-page 32-9 Development Tools Interchangeable target probes allow the system to be easily re-configured for emulation of different processors. The universal architecture of the PICMASTER allows expansion to support all new Microchip microcontrollers. 32 PICmicro MID-RANGE MCU FAMILY 32.6 MPLAB Programmer Support Microchip offers two levels of device programmer support. For most bench setups the PICSTART Plus is sufficient. When true system qualification is done, the PRO MATE II should be the minimum used, due to the validation of program memory at VDD min and VDD max for maximum reliability 32.6.1 PRO MATE(R) II: Universal Device Programmer The PRO MATE II Universal Programmer is a full-featured programmer capable of operating in stand-alone mode as well as PC-hosted mode. PRO MATE II operates under MPLAB or as a DOS command driven program. The PRO MATE II has programmable VDD and VPP supplies which allows it to verify programmed memory at VDD min and VDD max for maximum reliability. It has an LCD display for error messages, keys to enter commands and a modular detachable socket assembly to support various package types. In stand-alone mode the PRO MATE II can read, verify or program Baseline, Mid-Range, and High End devices. It can also set configuration and code-protect bits in this mode. The PRO MATE II programmer also supports Microchip's Serial EEPROM and KEELOQ(R) Security devices. A separate In-Circuit Serial Programming (ICSP) module is available for volume programming in a manufacturing environment. See the Programming module documentation for specific application requirements. 32.6.2 PICSTART(R) Plus Low-Cost Development Kit The PICSTART Plus programmer is an easy-to-use, low-cost prototype programmer. It connects to the PC via one of the COM (RS-232) ports. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. PICSTART Plus is not recommended for production programming, since it does not do program memory verification at VDDMIN and VDDMAX. PICSTART Plus supports all Baseline, Mid-Range, and High End devices. For devices with up more than 40 pins an adapter socket is required. DIP packages are the form factor that are directly supported. Other package types may be supported with adapter sockets. DS31032A-page 32-10 1997 Microchip Technology Inc. Section 32. Development Tools 32.7 Supplemental Tools Microchip endeavors to provide a broad range of solutions to our customers. Some of these products may fall outside the realm of the classic development tools and include more advanced topics such as high level languages, fuzzy logic, or visual programming aids. These tools are considered supplemental tools and may be available directly from Microchip or from another vendor. A comprehensive listing of alternate tool providers is contained in the Third Party Guide. 32.7.1 fuzzyTECH-MP Fuzzy Logic Development System The fuzzyTECH-MP fuzzy logic development tool is available in two versions - a low cost introductory version, MP Explorer, for designers to gain a comprehensive working knowledge of fuzzy logic system design, and a full-featured version, fuzzyTECH-MP, for implementing more complex systems. 32.7.2 MP-DriveWay - Application Code Generator MP-DriveWay is an easy-to-use Windows-based Application Code Generator. With MP-DriveWay you can visually configure all the peripherals in a PIC16/17 device and, with a click of the mouse, generate all the initialization and many functional code modules in C language. The output is fully compatible with Microchip's MPLAB-C C compiler. The code produced is highly modular and allows easy integration of your own code. 32.7.3 Third Party Guide Looking for something else? Microchip strongly encourages and supports it's Third Parties. Microchip publishes the "Third Party Guide". It is an extensive volume that provides: * * * * Company Product Contact Information Consultants For over 100 companies and 200 products. These products include Emulators, Device Programmers, Gang Programmers, Language Products, and other tool solutions. 1997 Microchip Technology Inc. DS31032A-page 32-11 32 Development Tools Both versions include Microchip's fuzzyLAB demonstration board for hands-on experience with fuzzy logic systems implementation. PICmicro MID-RANGE MCU FAMILY 32.8 Development Boards Development boards give a quick start on a circuit that demonstrates the capabilities of a particular device. The device program can then be modified for your own evaluation of the device functionality and operation. 32.8.1 PICDEM-1 Low-Cost PIC16/17 Demonstration Board The PICDEM-1 is a simple board which demonstrates the capabilities of several of Microchip's microcontrollers. The microcontrollers supported are: PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C710, PIC16C711, PIC16C8X, PIC17C42A, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The users can program the sample microcontrollers provided with the PICDEM-1 board, on a PRO MATE II or PICSTART-Plus programmer, and easily test firmware. The user can also connect the PICDEM-1 board to the PICMASTER emulator and download the firmware to the emulator for testing. Additional prototype area is available to build additional hardware. Some of the features include an RS-232 interface, a potentiometer for simulated analog input, push-button switches and eight LEDs connected to PORTB. 32.8.2 PICDEM-2 Low-Cost PIC16CXXX Demonstration Board The PICDEM-2 is a simple demonstration board that supports the PIC16C62, PIC16C63, PIC16C64, PIC16C65, PIC16C72, PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-2 board, on a PRO MATE II programmer or PICSTART-Plus, and easily test firmware. The PICMASTER emulator may also be used with the PICDEM-2 board to test firmware. Additional prototype area has been provided for additional hardware. Some of the features include a RS-232 interface, push-button switches, a potentiometer for simulated analog input, a Serial EEPROM to demonstrate usage of the I2C bus and separate headers for connection to an LCD module and a keypad. DS31032A-page 32-12 1997 Microchip Technology Inc. Section 32. Development Tools 32.8.3 PICDEM-3 Low-Cost PIC16CXXX Demonstration Board 32.8.4 PICDEM-14A Low-Cost PIC14C000 Demonstration Board The PICDEM-14A demo board is a general purpose platform which is provided to help evaluate the PIC14C000 mixed signal microcontroller. The board runs a PIC14C000 measuring the voltage of a potentiometer and the on-chip temperature sensor. The voltages are then calibrated to the internal bandgap voltage reference. The voltage and temperature data are then transmitted to the RS-232 port. This data can be displayed using a terminal emulation program, such as Windows Terminal. This demo board also includes peripherals that allow users to display data on an LCD panel, read from and write to a serial EEPROM, and prototype custom circuitry to interface to the microcontroller. 1997 Microchip Technology Inc. DS31032A-page 32-13 32 Development Tools The PICDEM-3 is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC package. It will also support future 44-pin PLCC microcontrollers that have an LCD Module. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers, provided with the PICDEM-3 board, on a PRO MATE II programmer or PICSTART Plus with an adapter socket, and easily test firmware. The PICMASTER emulator may also be used with the PICDEM-3 board to test firmware. Additional prototype area has been provided for adding hardware. Some of the features include an RS-232 interface, push-button switches, a potentiometer for simulated analog input, a thermistor and separate headers for connection to an external LCD module and a keypad. Also provided on the PICDEM-3 board is an LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature and day of the week. The PICDEM-3 provides an additional RS-232 interface and Windows 3.1 software for showing the de-multiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware de-multiplexer for the LCD signals. PICmicro MID-RANGE MCU FAMILY 32.9 Development Tools for Other Microchip Products 32.9.1 SEEVAL Evaluation and Programming System The SEEVAL Serial EEPROM Designer's Kit supports all Microchip 2-wire and 3-wire Serial EEPROMs. The kit includes everything necessary to read, write, erase or program special features of any Microchip SEEPROM product including Smart Serials and secure serials. The Total Endurance Disk is included to aid in trade-off analysis and reliability calculations. The total endurance kit can significantly reduce time-to-market and results in a more optimized system. 32.9.2 KEELOQ Evaluation and Programming Tools KEELOQ evaluation and programming tools supports Microchip's HCS Secure Data Products. The HCS evaluation kit includes an LCD display to show changing codes, a decoder to decode transmissions, and a programming interface to program test transmitters. DS31032A-page 32-14 1997 Microchip Technology Inc. Section 32. Development Tools 32.10 Related Application Notes This section lists application notes that are related to this section of the manual. These application notes may not be written specifically for the Mid-Range MCU family (that is they may be written for the Base-Line, or the High-End), but the concepts are pertinent, and could be used (with modification and possible limitations). The current application notes related to Microchip's development tools are: Title Air Flow using Fuzzy Logic Application Note # AN600 32 Development Tools 1997 Microchip Technology Inc. DS31032A-page 32-15 PICmicro MID-RANGE MCU FAMILY 32.11 Revision History Revision A This is the initial released revision of Microchip's development tools description. DS31032A-page 32-16 1997 Microchip Technology Inc. M Section 33. Code Development HIGHLIGHTS No material is available at this time. Please monitor the Microchip web site for the B revision of the Code Development section of the Mid-range Reference Manual. 33 Code Development 1997 Microchip Technology Inc. DS30133A page 33-1 PICmicro MID-RANGE MCU FAMILY 33.1 Revision History Revision A This is the initial released revision for the Code Development with a PICmicroTM description. DS30133A-page 33-2 1997 Microchip Technology Inc. M Section 34. Appendix HIGHLIGHTS This section of the manual contains the following major topics: Appendix A:I2C Overview....................................................................................................34-2 Appendix B:List of LCD Glass Manufacturers ......................................................................34-11 Appendix C:Device Enhancement .......................................................................................34-13 Appendix D:Revision History................................................................................................34-19 34 Appendix I2C is a trademark of Philips Corporation. 1997 Microchip Technology Inc. DS31034A page 34-1 PICmicro MID-RANGE MCU FAMILY APPENDIX A: I 2C OVERVIEW This section provides an overview of the Inter-Integrated Circuit (I 2CTM) bus, with Subsection A.2 "Addressing I2C Devices" discussing the operation of the SSP modules in I 2C mode. The I 2C bus is a two-wire serial interface. The original specification, or standard mode, is for data transfers of up to 100 Kbps. An enhanced specification, or fast mode (400 Kbps) is supported. Standard and Fast mode devices will operate when attached to the same bus, if the bus operates at the speed of the slower device. The I 2C interface employs a comprehensive protocol to ensure reliable transmission and reception of data. When transmitting data, one device is the "master" which initiates transfer on the bus and generates the clock signals to permit that transfer, while the other device(s) acts as the "slave." All portions of the slave protocol are implemented in the SSP module's hardware, except general call support, while portions of the master protocol need to be addressed in the PIC16CXX software. The MSSP module supports the full implementation of the I 2C master protocol, the general call address, and data transfers upto 1 Mbps. The 1 Mbps data transfers are supported by some of Microchips Serial EEPROMs. Table A-1 defines some of the I 2C bus terminology. In the I 2C interface protocol each device has an address. When a master wishes to initiate a data transfer, it first transmits the address of the device that it wishes to "talk" to. All devices "listen" to see if this is their address. Within this address, a bit specifies if the master wishes to read-from/write-to the slave device. The master and slave are always in opposite modes (transmitter/receiver) of operation during a data transfer. That is they can be thought of as operating in either of these two relations: * Master-transmitter and Slave-receiver * Slave-transmitter and Master-receiver In both cases the master generates the clock signal. The output stages of the clock (SCL) and data (SDA) lines must have an open-drain or open-collector in order to perform the wired-AND function of the bus. External pull-up resistors are used to ensure a high level when no device is pulling the line down. The number of devices that may be attached to the I 2C bus is limited only by the maximum bus loading specification of 400 pF and addressing capability. DS31034A-page 34-2 1997 Microchip Technology Inc. Appendix A A.1 Initiating and Terminating Data Transfer During times of no data transfer (idle time), both the clock line (SCL) and the data line (SDA) are pulled high through the external pull-up resistors. The START and STOP conditions determine the start and stop of data transmission. The START condition is defined as a high to low transition of the SDA when the SCL is high. The STOP condition is defined as a low to high transition of the SDA when the SCL is high. Figure A-1 shows the START and STOP conditions. The master generates these conditions for starting and terminating data transfer. Due to the definition of the START and STOP conditions, when data is being transmitted, the SDA line can only change state when the SCL line is low. Figure A-1: Start and Stop Conditions SDA SCL S Start Condition Table A-1: Term Transmitter Receiver Master Slave Multi-master Arbitration Synchronization P Change of Data Allowed Change of Data Allowed Stop Condition I2C Bus Terminology Description The device that sends the data to the bus. The device that receives the data from the bus. The device which initiates the transfer, generates the clock and terminates the transfer. The device addressed by a master. More than one master device in a system. These masters can attempt to control the bus at the same time without corrupting the message. Procedure that ensures that only one of the master devices will control the bus. This ensure that the transfer data does not get corrupted. Procedure where the clock signals of two or more devices are synchronized. 34 Appenidx 1997 Microchip Technology Inc. DS31034A-page 34-3 PICmicro MID-RANGE MCU FAMILY A.2 Addressing I 2C Devices There are two address formats. The simplest is the 7-bit address format with a R/W bit (Figure A-2). The more complex is the 10-bit address with a R/W bit (Figure A-3). For 10-bit address format, two bytes must be transmitted. The first five bits specify this to be a 10-bit address format. The 1st transmitted byte has 5-bits which specify a 10-bit address, the two MSbs of the address, and the R/W bit. The second byte is the remaining 8-bits of the address. Figure A-2: 7-bit Address Format MSb LSb R/W S slave address S R/W ACK Figure A-3: ACK Sent by Slave Start Condition Read/Write pulse Acknowledge I2C 10-bit Address Format S 1 1 1 1 0 A9 A8 R/W ACK A7 A6 A5 A4 A3 A2 A1 A0 ACK sent by slave = 0 for write S R/W ACK DS31034A-page 34-4 - Start Condition - Read/Write Pulse - Acknowledge 1997 Microchip Technology Inc. Appendix A A.3 Transfer Acknowledge All data must be transmitted per byte, with no limit to the number of bytes transmitted per data transfer. After each byte, the slave-receiver generates an acknowledge bit (ACK) (Figure A-4). When a slave-receiver doesn't acknowledge the slave address or received data, the master must abort the transfer. The slave must leave SDA high so that the master can generate the STOP condition (Figure A-1). Figure A-4: Slave-Receiver Acknowledge Data Output by Transmitter Data Output by Receiver not acknowledge acknowledge SCL from Master 1 8 2 S Start Condition 9 Clock Pulse for Acknowledgment If the master is receiving the data (master-receiver), it generates an acknowledge signal for each received byte of data, except for the last byte. To signal the end of data to the slave-transmitter, the master does not generate an acknowledge (not acknowledge). The slave then releases the SDA line so the master can generate the STOP condition. The master can also generate the STOP condition during the acknowledge pulse for valid termination of data transfer. If the slave needs to delay the transmission of the next byte, holding the SCL line low will force the master into a wait state. Data transfer continues when the slave releases the SCL line. This allows the slave to move the received data or fetch the data it needs to transfer before allowing the clock to start. This wait state technique can also be implemented at the bit level, Figure A-5. Figure A-5: Data Transfer Wait State SDA MSB acknowledgment signal from receiver byte complete interrupt with receiver acknowledgment signal from receiver 34 clock line held low while interrupts are serviced SCL S 1 1997 Microchip Technology Inc. Address 7 8 R/W 9 ACK 1 Wait State 2 Data 3*8 9 ACK P Stop Condition DS31034A-page 34-5 Appenidx Start Condition 2 PICmicro MID-RANGE MCU FAMILY Figure A-6 and Figure A-7 show Master-transmitter and Master-receiver data transfer sequences. Figure A-6: Master-Transmitter Sequence For 7-bit address: S Slave Address R/W A Data A Data A/A P '0' (write) data transferred (n bytes - acknowledge) A master transmitter addresses a slave receiver with a 7-bit address. The transfer direction is not changed. For 10-bit address: S Slave Address R/W A1 Slave Address A2 Data A (Code + A9:A8) (A7:A0) Data A/A P (write) A master transmitter addresses a slave receiver with a 10-bit address. From master to slave From slave to master Figure A-7: A = acknowledge (SDA low) A = not acknowledge (SDA high) S = Start Condition P = Stop Condition Master-Receiver Sequence For 7-bit address: S Slave Address R/W A Data A Data A P '1' (read) data transferred (n bytes - acknowledge) A master reads a slave immediately after the first byte. For 10-bit address: S Slave Address R/W A1 Slave Address (A7:A0) (Code + A9:A8) (write) A2 Sr Slave Address R/W A3 Data A (Code + A9:A8) Data A P (read) A master transmitter addresses a slave receiver with a 10-bit address. From master to slave From slave to master DS31034A-page 34-6 A = acknowledge (SDA low) A = not acknowledge (SDA high) S = Start Condition P = Stop Condition 1997 Microchip Technology Inc. Appendix A When a master does not wish to relinquish the bus (which occurs by generating a STOP condition), a repeated START condition (Sr) must be generated. This condition is identical to the start condition (SDA goes high-to-low while SCL is high), but occurs after a data transfer acknowledge pulse (not the bus-free state). This allows a master to send "commands" to the slave and then receive the requested information or to address a different slave device. This sequence is shown in Figure A-8. Figure A-8: Combined Format (read or write) (n bytes + acknowledge) S Slave Address R/W A Data A/A Sr Slave Address R/W A Data A/A P (read) Sr = repeated Start Condition (write) Direction of transfer may change at this point Transfer direction of data and acknowledgment bits depends on R/W bits. Combined format: Sr Slave Address R/W A Slave Address A Data A (Code + A9:A8) (A7:A0) Data A/A Sr Slave Address R/W A Data A (Code + A9:A8) Data A P (read) (write) Combined format - A master addresses a slave with a 10-bit address, then transmits data to this slave and reads data from this slave. From master to slave From slave to master A = acknowledge (SDA low) A = not acknowledge (SDA high) S = Start Condition P = Stop Condition 34 Appenidx 1997 Microchip Technology Inc. DS31034A-page 34-7 PICmicro MID-RANGE MCU FAMILY A.4 Multi-master The I2C protocol allows a system to have more than one master. This is called multi-master. When two or more masters try to transfer data at the same time, arbitration and synchronization occur. A.4.1 Arbitration Arbitration takes place on the SDA line, while the SCL line is high. The master which transmits a high when the other master transmits a low loses arbitration (Figure A-9), and turns off its data output stage. A master which lost arbitration can generate clock pulses until the end of the data byte where it lost arbitration. When the master devices are addressing the same device, arbitration continues into the data. Figure A-9: Multi-Master Arbitration (Two Masters) transmitter 1 loses arbitration DATA 1 SDA DATA 1 DATA 2 SDA SCL Masters that also incorporate the slave function, and have lost arbitration must immediately switch over to slave-receiver mode. This is because the winning master-transmitter may be addressing it. Arbitration is not allowed between: * A repeated START condition * A STOP condition and a data bit * A repeated START condition and a STOP condition Care needs to be taken to ensure that these conditions do not occur. DS31034A-page 34-8 1997 Microchip Technology Inc. Appendix A A.4.2 Clock Synchronization Clock synchronization occurs after the devices have started arbitration. This is performed using a wired-AND connection to the SCL line. A high to low transition on the SCL line causes the concerned devices to start counting off their low period. Once a device clock has gone low, it will hold the SCL line low until its SCL high state is reached. The low to high transition of this clock may not change the state of the SCL line, if another device clock is still within its low period. The SCL line is held low by the device with the longest low period. Devices with shorter low periods enter a high wait-state, until the SCL line comes high. When the SCL line comes high, all devices start counting off their high periods. The first device to complete its high period will pull the SCL line low. The SCL line high time is determined by the device with the shortest high period, Figure A-10. Figure A-10: Clock Synchronization wait state start counting HIGH period CLK 1 CLK 2 counter reset SCL Figure A-11: SCL I2C Bus Start/Stop Bits Timing Specification 93 91 90 92 SDA 34 STOP Condition START Condition Microchip Parameter No. Sym I2C Bus Start/Stop Bits Timing Specification Characteristic Min Typ Max Units Conditions Only relevant for repeated START condition After this period the first clock pulse is generated 90 TSU:STA START condition Setup time 100 kHz mode 400 kHz mode 4700 600 -- -- -- -- ns 91 THD:STA TSU:STO 93 THD:STO 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 4000 600 4700 600 4000 600 -- -- -- -- -- -- -- -- -- -- -- -- ns 92 START condition Hold time STOP condition Setup time STOP condition Hold time 1997 Microchip Technology Inc. ns ns DS31034A-page 34-9 Appenidx Table A-2: PICmicro MID-RANGE MCU FAMILY I2C Bus Data Timing Specification Figure A-12: 103 102 100 101 SCL 90 106 107 91 92 SDA In 110 109 109 SDA Out Table A-3: Microchip Parameter No. I2C Bus Data Timing Specification Sym Characteristic 100 THIGH Clock high time 101 TLOW Clock low time 102 TR SDA and SCL rise time 103 TF 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode SDA and SCL fall 100 kHz mode time 400 kHz mode 90 TSU:STA START condition setup time 91 THD:STA START condition hold time 106 THD:DAT Data input hold time 107 TSU:DAT Data input setup time 92 TSU:STO STOP condition setup time 109 TAA Output valid from clock 110 TBUF Bus free time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Min Max Units 4.0 0.6 4.7 1.3 -- 20 + 0.1Cb -- 20 + 0.1Cb 4.7 0.6 4.0 0.6 0 0 250 100 4.7 0.6 -- -- 4.7 1.3 -- -- -- -- 1000 300 s s s s ns ns 300 300 ns ns -- -- -- -- -- 0.9 -- -- -- -- 3500 1000 -- -- s s s s ns s ns ns s s ns ns s s Conditions Cb is specified to be from 10 to 400 pF Cb is specified to be from 10 to 400 pF Only relevant for repeated START condition After this period the first clock pulse is generated Note 2 Note 1 Time the bus must be free before a new transmission can start D102 Cb Bus capacitive loading -- 400 pF Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but the requirement tsu;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released. DS31034A-page 34-10 1997 Microchip Technology Inc. Appendix B APPENDIX B: LIST OF LCD GLASS MANUFACTURERS AEG-MIS 3340 Peachtree Rd. NE Suite 500 Atlanta, GA 30326 TEL: 404-239-0277 FAX: 404-239-0383 Interstate Electronics Corp. 1001 E. Bull Rd. Anaheim, CA 92805 TEL: 800-854-6979 FAX: 714-758-4111 All Shore INDS Inc. 1 Edgewater Plaza Staten Island, NY 10305 TEL: 718-720-0018 FAX: 718-720-0225 Kent Display Systems 343 Portage Blvd. Kent, OH 44240 TEL: 330-673-8784 Crystaloid 5282 Hudson Drive Hudson, OH 44236-3769 TEL: 216-655-2429 FAX: 216-655-2176 LCD Planar Optics Corporation 2100-2 Artic Ave. Bohemia, NY 11716 TEL: 516-567-4100 FAX: 516-567-8516 DCI Inc. 14812 W. 117th St. Olathe, KS 66062-9304 TEL: 913-782-5672 FAX: 913-782-5766 LXD Inc. 7650 First Place Oakwood Village, OH 44146 TEL: 216-786-8700 FAX: 216-786-8711 Excel Technology International Corporation Unit 5, Bldg. 4, Stryker Lane Belle Mead, NJ 08502 TEL: 908-874-4747 FAX: 908-874-3278 Nippon Sheet Glass Tomen America Inc. 1285 Avenue of the Americas New York, NY 10019 TEL: 212-397-4600 FAX: 212-397-3351 F-P Electronics/Mark IV Industries 6030 Ambler Drive Mississauga, ON Canada L4W 2PI TEL: 905-624-3020 FAX: 905-238-3141 OPTREX America 44160 Plymouth Oaks Blvd. Plymouth, MI 48170 TEL: 313-416-8500 FAX: 313-416-8520 Hunter Components 24800 Chagrin Blvd, Suite 101 Cleveland, OH 44122 TEL: 216-831-1464 FAX: 216-831-1463 Phillips Components LCD Business Unit 1273 Lyons Road, Bldg G Dayton, OH 45459 TEL: 573-436-9500 FAX: 573-436-2230 34 Appenidx 1997 Microchip Technology Inc. DS31034A-page 34-11 PICmicro MID-RANGE MCU FAMILY Satori Electric 23717 Hawthorne Blvd. 3rd Floor Torrance, CA 90505 TEL: 310-214-1791 FAX: 310-214-1721 Varitronix Limited Inc. 3250 Wilshire Blvd. Suite 1901 Los Angeles, CA 90010 TEL: 213-738-8700 FAX: 213-738-5340 Seiko Instruments USA Inc. Electronic Components Division 2990 West Lomita Blvd. Torrance, CA 90505 TEL: 213-517-7770 213-517-8113 FAX: 213-517-7792 Varitronix Limited Inc. 4/F, Liven House 61-63 King Yip Street Kwun Tong, Kowloon Hong Kong TEL: 852 2389 4317 FAX: 852 2343 9555 Standish International European Technical Center Am Baumstuck II 65520 Bad Camberg/Erbach Germany TEL: 011 49 6434 3324 FAX: 011 49 6434 377238 Varitronix (France) S.A.R.L. 13/15 Chemin De Chilly 91160 Champlain France TEL:(33) 1 69 09 7070 FAX:(33) 1 69 09 0535 Standish LCD W7514 Highway V Lake Mills, WI 53551 TEL: 414-648-1000 FAX: 414-648-1001 Varitronix Italia, S.R.L. Via Bruno Buozzi 90 20099 Sesto San Giovanni Milano, Italy TEL:(39) 2 2622 2744 FAX:(39) 2 2622 2745 Truly Semiconductors Ltd. (USA) 2620 Concord Ave. Suite 106 Alhambra, CA 91803 TEL: 818-284-3033 FAX: 818-284-6026 Varitronix (UK) Limited Display House, 3 Milbanke Court Milbanke Way, Bracknell Berkshire RG12 1BR United Kingdom TEL:(44) 1344 30377 FAX(44) 1344 300099 Truly Semiconductor Ltd. 2/F, Chung Shun Knitting Center 1-3 Wing Yip Street, Kwai Chung, N.T., Hong Kong TEL: 852 2487 9803 FAX: 852 2480 0126 Varitronix (Canada) Limited 18 Crown Steel Drive, Suite 101 Markham, Ontario Canada L3R 9X8 TEL:(905) 415-0023 FAX:(905) 415-0094 Vikay America Inc. 195 W. Main St. Avon, CT 06001-3685 TEL: 860-678-7600 FAX: 860-678-7625 DS31034A-page 34-12 1997 Microchip Technology Inc. Appendix C APPENDIX C: DEVICE ENHANCEMENT As the Midrange architecture matured, certain modules and features have been enhanced. They are: 1. 2. 3. 4. 5. 6. 7. The data memory map The SSP module The A/D module Brown-out Reset added to the core MCLR Filter USART Device Oscillator The following subsections discuss the implementations of these enhancements. C.1 Data Memory Map The Data Memory Map shows the location of the Special Function Registers (SFRs) and the General Purpose Registers (GPRs). SFRs provide controls and give status on the operation of the device, while the GPRs are the general purpose RAM. Figure C-1 show the various memory maps that have been implemented in the midrange family. Memory Map A was implemented on the first midrange devices. They were 18/20-pin devices that had limited peripheral features. When the product roadmap dictated the requirement for devices with increased I/O, and a richer peripheral set, memory map B was implemented. Memory map C is actually a subset of memory map B, but context saving (due to an interrupt) requires additional software overhead. This is because there is no GPR in Bank1. To minimize the context saving software, memory map D was defined. A common RAM memory map will be used for all future devices. See the "Memory Organization" section for use and implementation of the Midrange PICmicro's memory. Figure C-1: Various Data Memory Maps A C B 00h 0Bh 0Ch 80h SFR SFR 00h 8Bh 8Ch 1Fh 20h (1) GPR 7Fh FFh SFR SFR GPR GPR 7Fh Bank0 Bank1 80h 00h 9Fh A0h 1Fh 20h 80h SFR GPR FFh SFR 9Fh A0h (2) 7Fh FFh Appenidx D(3) 00h 1Fh 20h 80h SFR 9Fh A0h F0h FFh Bank0 11Fh 120h GPR GPR 70h 7Fh 100h SFR (1) Bank1 180h SFR 19Fh 1A0h (1) Bank2 SFR GPR GPR 170h 17Fh 1F0h 1FFh (1) Bank3 Note 1: Mapped in Bank0. 2: Unimplemented, read as '0'. 3: Some devices have some GPR located in the SFR region. 1997 Microchip Technology Inc. 34 Bank0 Bank1 Bank0 Bank1 DS31034A-page 34-13 PICmicro MID-RANGE MCU FAMILY C.2 SSP (Synchronous Serial Port) Module The SSP module has two modes of operation; * SPI (Serial Peripheral Interface) * I2C (Inter-Integrated Circuit). There are now three different SSP modules that exist in Microchip's design library. The first SSP module (now called Basic SSP) implements two of the four SPI modes, and the I2C module in slave mode. The second SSP module (called SSP) implements all four SPI modes, and the I2C module in slave mode. The third SSP module (called Master SSP) implements all four SPI modes, and the I2C module in master and slave modes. Table C-1 shows the devices that have an SSP module and denotes which version is implemented. As new devices are introduced, either the SSP module or Master SSP module will be implemented (that is, the Basic SSP module is being phased out). Only select devices will be introduced with the Master SSP module due to the size (silicon area => cost) difference in relation to the SSP module. If your application requires I2C Master mode, then you should also check into Microchip's high-end family, PIC17CXXX. Table C-1: Devices With an SSP module Synchronous Serial Port Version Device SSP Basic SSP Master SSP (1) PIC16C62 -- Yes -- PIC16C62A -- Yes -- -- -- -- -- -- -- -- -- -- Yes Yes -- Yes -- -- -- -- Yes Yes Yes Yes See Device Data Sheet Yes Yes Yes Yes Yes Yes Yes Yes Yes -- -- Yes -- Yes Yes Yes Yes -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- See Device Data Sheet PIC16CR62 PIC16C63 PIC16CR63 PIC16C64 PIC16C64A PIC16CR64 PIC16C65 PIC16C65A PIC16CR65 PIC16C66 PIC16C67 PIC16C72 PIC16CR72 PIC16C73 PIC16C73A PIC16C74 PIC16C74A PIC16C76 PIC16C77 PIC16C923 PIC16C924 Future Devices with SSP module -- Note 1: At present NO midrange devices are available with the Master SSP module. Please refer to Microchip's Web site or BBS for release of Product Briefs. You will be able to find out the details of features for new devices. This module is available on Microchip's High End family (PIC17CXXX). Please refer to Microchip's Web site, BBS, Regional Sales Office, or Factory Representatives. DS31034A-page 34-14 1997 Microchip Technology Inc. Appendix C C.3 A/D (Analog-to-Digital) Module There now exists several different versions of the A/D module in Microchip's design library. The first A/D module (now called Basic 8-bit A/D) is an 8-bit A/D with four input channels. The second A/D module (called 8-bit A/D) is an 8-bit A/D with up to 8 input channels. The Third A/D module (called 10-bit A/D) is a 10-bit A/D with up to16 input channels implemented. Table C-2 shows which devices have an A/D module, and the version implemented. As new devices are introduced, either the 8-bit A/D module or 10-bit A/D module will be implemented (that is the Basic 8-bit A/D module is being phased out). If your application requires the 10-bit A/D, you should refer to Microchip's High End Family (PIC17CXXX). This family currently has some devices that have this module implemented. Table C-2: Devices With A/D modules Device PIC16C710 PIC16C71 PIC16C711 PIC16C715 PIC16C72 PIC16CR72 PIC16C73 PIC16C73A PIC16C74 PIC16C74A PIC16C76 PIC16C77 PIC16C924 PIC14C000 Future Devices with A/D module 8-bit A/D Basic 8-bit A/D 10-bit A/D (1) -- -- -- -- Yes Yes Yes Yes Yes Yes Yes Yes Yes -- See Device Data Sheet Yes Yes Yes Yes -- -- -- -- -- -- -- -- -- -- See Device Data Sheet -- -- -- -- -- -- -- -- -- -- -- -- -- -- See Device Data Sheet Slope A/D -- Yes See Device Data Sheet Note 1: At present NO midrange devices are available with the 10-bit A/D module. Please refer to Microchip's Web site or BBS for release of Product Briefs. You will be able to find out the details of features for new devices. This module is available on Microchip's High End family (PIC17CXXX). Please refer to Microchip's Web site, BBS, Regional Sales Office, or Factory Representatives. 34 Appenidx 1997 Microchip Technology Inc. DS31034A-page 34-15 PICmicro MID-RANGE MCU FAMILY C.4 Brown-out Reset An internal Brown-out Reset (BOR) circuit was added as a special feature. This circuit will be added to most new devices. The exception will be for devices whose target market will require normal operation below the BOR trip point (handheld battery applications). Table C-3 shows the devices that evolved into having the BOR circuitry. Table C-3: C.5 Devices That Were Revised to Include On-chip Brown-out Reset Base Device No Brown-out Reset Subsequent Device with Brown-out Reset PIC16C62 PIC16C64 PIC16C65 PIC16C71 PIC16C73 PIC16C74 PIC16C62A PIC16C64A PIC16C65A PIC16C711 PIC16C73A PIC16C74A Comparator If a change in the CMCON register (C1OUT or C2OUT) should occur when a read operation is being executed (start of the Q2 cycle), then the CMIF interrupt flag bit may not get set. DS31034A-page 34-16 1997 Microchip Technology Inc. Appendix C C.6 MCLR Filter The master clear (MCLR) logic has had a filter added. This filter ignores short duration (glitch) low level pulses on the Master Clear pin. Table C-4 shows whether the device has the master clear filter. Table C-4: Devices With Master Clear Filter Master Clear Device 1997 Microchip Technology Inc. Filter Yes Yes -- -- -- -- Yes -- -- Yes -- -- -- -- -- -- -- -- Yes -- -- -- -- Yes -- Yes -- -- -- Yes Yes Yes Yes -- -- -- -- -- Yes Yes Yes Yes -- Yes Yes -- Yes Yes Yes Yes Yes Yes Yes Yes -- Yes Yes Yes Yes -- Yes -- Yes Yes Yes -- -- -- -- Yes Yes Yes DS31034A-page 34-17 34 Appenidx PIC16C61 PIC16C62 PIC16C62A PIC16CR62 PIC16C63 PIC16CR63 PIC16C64 PIC16C64A PIC16CR64 PIC16C65 PIC16C65A PIC16CR65 PIC16C66 PIC16C67 PIC16C620 PIC16C621 PIC16C622 PIC16C710 PIC16C71 PIC16C711 PIC16C715 PIC16C72 PIC16CR72 PIC16C73 PIC16C73A PIC16C74 PIC16C74A PIC16C76 PIC16C77 PIC16C83 PIC16C84 PIC16F83 PIC16F84 PIC16C923 PIC16C924 All New Devices No Filter (Fast Reset) PICmicro MID-RANGE MCU FAMILY C.7 USART The original USART/SCI module that was offered on Midrange devices specified a "high speed" mode (when the BRGH control bit is set). Due to the design of the sampling circuitry, the operation of this mode was not as robust as desired. The sampling circuitry has been changed so that operation now meets Microchip's requirements. The difference in the sampling is described in the "USART" section. Table C-5 shows which devices use the new and old sampling logic. Table C-5: USART/SCI Sampling Logic Sampling Logic Device PIC16C63 PIC16CR63 PIC16C65 PIC16C65A PIC16CR65 PIC16C66 PIC16C67 PIC16C73 PIC16C73A PIC16C74 PIC16C74A PIC16C76 PIC16C77 New Devices with USART/SCI module C.8 Old New Yes Yes Yes Yes Yes -- -- Yes Yes Yes Yes -- -- -- -- -- -- -- Yes Yes -- -- -- -- Yes Yes -- Yes Device Oscillator A new mode has been added into the device oscillator which allows the device to operate from an internal RC. This is specified at time of device programming (configuration word). This mode will be included on many future devices. See the device data sheets configuration word to determine if the device supports this mode. C.9 Parallel Slave Port The control pins have changed from level sensitive to edge sensitive. Table C-6: Parallel Slave Port Change Sensitivity Sensitivity Device PIC16C64 PIC16C64A PIC16C65 PIC16C65A PIC16C67 PIC16C74 PIC16C74A PIC16C77 New Devices with Parallel Slave Port DS31034A-page 34-18 Level Edge Yes -- Yes -- -- Yes -- -- -- Yes -- Yes Yes -- Yes Yes -- Yes 1997 Microchip Technology Inc. Appendix D APPENDIX D: REVISION HISTORY Revision A This is the initial released revision of the Reference Guide Appendix. 34 Appenidx 1997 Microchip Technology Inc. DS31034A-page 34-19 PICmicro MID-RANGE MCU FAMILY DS31034A-page 34-20 1997 Microchip Technology Inc. M Section 35. Glossary A A/D See Analog to Digital. Acquisition Time (TACQ) This is related to Analog to Digital (A/D) converters. This is the time that the A/D's holding capacitor acquires the analog input voltage level connected to it. When the GO bit is set, the analog input is disconnected from the holding capacitor and the A/D conversion is started. ALU Arithmetical Logical Unit. Device logic that is responsible for the mathematical (add, subtract, ...), logical (and, or, ...), and shifting operations. Analog to Digital (A/D) The conversion of an analog input voltage to a ratiometric digital equivalent value. Assembly Language A symbolic language that describes the binary machine code in a readable form. 35 Glossary 1997 Microchip Technology Inc. DS31035A page 35-1 PICmicro MID-RANGE MCU FAMILY B Bank This is a method of addressing Data Memory. Since midrange devices have 7-bits for direct addressing, instructions can address up to 128 bytes (including special function registers). To allow more data memory to be present on a device, data memory is partitioned into contiguous banks of 128 bytes each. To select the desired bank, the bank selection bits (RP1:RP0) need to be appropriately configured. Since there are presently 2 bank selection bits, 4 banks can be implemented. Baud Generally how the communication speed of serial ports is described. Equivalent to bits per second (bps). BCD See Binary Coded Decimal. Binary Coded Decimal (BCD) Each 4-bit nibble expresses a digit from 0-9. Usually two digits are packed to a byte giving a range of 0 - 99. BOR See Brown-out Reset. Brown-out A condition where the supply voltage of the device temporarily falls below the specified minimum operation point. This can occur when a load is switched on and causes the system/device voltage to drop. Brown-out Reset (BOR) Circuitry which will force the device to the reset state if the (device) voltage falls below a specified voltage level. Some devices have an internal BOR circuit, while other devices would require an external circuit to be created. Bus width This is the number of bits of information that the bus carries. For the Data Memory, the bus width is 8-bits. For the midrange devices the Program Memory bus width is 14-bits. DS31035A-page 35-2 1997 Microchip Technology Inc. Glossary C Capture A function of the CCP module in which the value of a timer/counter is "captured", into a holding register, when a predetermined event occurs. CCP Capture, Compare, Pulse Width Modulation (PWM). This module can be configured to operate as an input capture, or a timer compare, or a PWM output. Common RAM This is a region of the data memory RAM that is the same RAM location across all banks. This common RAM maybe implemented between addresses 70h -7Fh (inclusive). This common area is useful for the saving of required variables during context switching (such as during an interrupt). Compare A function of the CCP module in which the device will perform an action when a timer's register value matches the value in the compare register. Compare Register A 16-bit register that contains a value that is compared to the 16-bit TMR1 register. The compare function triggers when the counter matches the contents of the compare register. Capture Register A 16-bit register that gets loaded with the value of the 16-bit TMR1 register when a capture event occurs. Configuration Word This is a location that specifies the characteristics that the device will have for operation (such as oscillator mode, WDT enable, start-up timer enables). These characteristics can be specified at time of device programming. For EPROM memory devices, as long as the bit is a '1', it may at a later time be programmed as a '0'. The device must be erased for a '0' to be returned to a '1'. Conversion Time (Tconv) This is related to Analog to Digital (A/D) converters. This is the time that the A/D converter requires to convert the analog voltage level on the holding capacitor to a digital value. CPU Central Processing Unit. Decodes the instructions, and determines the operands that are needed and the operations that need to be done. Arithmetic, logical, or shift operations will be passed to the ALU. 35 Glossary 1997 Microchip Technology Inc. DS31035A-page 35-3 PICmicro MID-RANGE MCU FAMILY D D/A See Digital to analog DAC Digital to analog converter Data Bus The bus which is used to transfer data to and from the data memory. Data EEPROM Data Electrically Erasable Programmable Read Only Memory. This memory has the capability to be programmed and re-programmed by the CPU to ensure that in the case of a power loss critical values/variables are retained in the non-volatile memory. Data Memory The memory that is on the Data Bus. This memory is volatile (SRAM) and contains both the Special Function Registers and General Purpose Registers. Direct Addressing When the Data Memory Address is contained in the Instruction. The execution of this type of instruction will always access the data at the embedded address. Digital to Analog E EEPROM Electrically Erasable Programmable Read Only Memory. This memory has the capability to be programmed and erased in-circuit. EPROM Electrically Programmable Read Only Memory. This memory has the capability to be programmed in-circuit. Erasing requires that the program memory be exposed to UV light. EXTRC External Resistor-Capacitor (RC). Some devices have a device oscillator option that allows the clock to come from an external RC. This is the same as RC mode on some devices. F Flash Memory This memory has the capability to be programmed and erased in-circuit. Program Memory technology that is almost functionally equivalent to Program EEPROM Memory. Fosc Frequency of the device oscillator. DS31035A-page 35-4 1997 Microchip Technology Inc. Glossary G GIO General Input/Output GPIO General Purpose Input/Output GPR General Purpose Register (RAM). A portion of the data memory that can be used to store the program's dynamic variables. H Harvard Architecture In this architecture the Program Memory and Data Memory buses are separated. This allows concurrent accesses to Data Memory and Program Memory, which increases the performance of the device. Holding Capacitor This is a capacitor in the Analog to Digital (A/D) module which "holds" to analog input level once the conversion is started. During acquisition, the holding capacitor is charged/discharged by the voltage level on the analog input pin. Once the conversion is started, the holding capacitor is disconnected from the analog input and "holds" this voltage for the A/D conversion. HS High Speed. One of the device oscillator modes. The oscillator circuit is tuned to support the high frequency operation. Used for operation from 4 MHz to 20 MHz. 35 Glossary 1997 Microchip Technology Inc. DS31035A-page 35-5 PICmicro MID-RANGE MCU FAMILY I I2C Inter-Integrated Circuit. This is a two wire communication interface. This feature is one of the modes of the SSP module. Indirect Addressing When the Data Memory Address is not contained in the Instruction. The instruction operates on the INDF address, which causes the Data Memory Address to be the value in the FSR register. The execution of the instruction will always access the data at the address pointed to by the FSR register. Instruction Bus The bus which is used to transfer instruction words from the program memory to the CPU. Instruction Fetch Due to the Harvard architecture, when one instruction is to be executed, the next location in program memory is "fetched" and ready to be decoded as soon as the currently executing instruction is completed. Instruction cycle The events for an instruction to execute. There are four events which can generally be described as: Decode, Read, Execute, and Write. Not all events will be done by all instructions. To see the operations during the instruction cycle, please look in the description of each instruction. Four external clocks (Tosc) make one instruction cycle (TCY). Interrupt A signal to the CPU that causes the program flow to be forced to the Interrupt Vector Address (04h in program memory). Before the program flow is changed, the contents of the Program Counter (PC) are forced onto the hardware stack, so that program execution may return to the interrupted point. INTRC Internal Resistor-Capacitor (RC). Some devices have a device oscillator option that allows the clock to come from an internal RC. DS31035A-page 35-6 1997 Microchip Technology Inc. Glossary L LCD Liquid Crystal Display. Useful for giving visual status of a system. This may require the specification of custom LCD glass. LED Light Emitting Diode. Useful for giving visual status of a system. Literal This is a constant value that is embedded in an instruction word. Long Word Instruction An instruction word that embeds all the required information (opcode and data) into a single word. This ensures that every instruction is accessed and executed in a single instruction cycle. LP One of the device oscillator modes. Used for low frequency operation which allows the oscillator to be tuned for low power consumption. Operation is up to 200 kHz. LSb Least Significant Bit. LSB Least Significant Byte. M Machine cycle This is a concept where the device clock is divided down to a unit time. For PICmicros this unit time is 4 times the device oscillator (4TOSC), also known as TCY. MSb Most Significant Bit. MSB Most Significant Byte. 35 Glossary 1997 Microchip Technology Inc. DS31035A-page 35-7 PICmicro MID-RANGE MCU FAMILY N Non-Return to Zero Two level encoding used to transmit data over a communications medium. A bit value of '1' indicates a high voltage signal. A bit value of '0' indicates a low voltage signal. The data line defaults to a high level. NRZ See Non-Return to Zero O Opcode The portion of the 14-bit instruction word that specifies the operation that needs to occur. The opcode is of variable length depending on the instruction that needs to be executed. The opcode varies from 4-bits to x-bits. The remainder of the instruction word contains program or data memory information. Oscillator Start-up Timer (OST) This timer counts 1024 crystal/resonator oscillator clock before releasing the internal reset signal. OST See Oscillator Start-up Timer. DS31035A-page 35-8 1997 Microchip Technology Inc. Glossary P Pages Method of addressing the Program Memory. Midrange devices have 11-bit addressing for CALL and GOTO instructions, which gives these instructions a 2-Kword reach. To allow more program memory to be present on a device, program memory is partitioned into contiguous pages, where each page is 2-Kwords. To select the desired page, the page selection bits (PCLATCH<5:4>) need to be appropriately configured. Since there are presently 2 page selection bits, 4 pages can be implemented. Parallel Slave Port (PSP) A parallel communication port which is used to interface to a microprocessor's 8-bit data bus. POP A termed used to refer to the action of restoring information from a stack (software and/or hardware). See PUSH. Postscaler A circuit that slows the rate of the interrupt generation (or WDT reset) from a counter/timer by dividing it down. Power-on Reset POR) Circuitry which determines if the device voltage rose from a powered down level (0V). If the device voltage is rising from ground, a device reset occurs and the PWRT is started. Power-up Timer (PWRT) A timer which holds the internal reset signal low for a timed delay to allow the device voltage to reach the valid operating voltage range. Once the timer times out, the OST circuitry is enabled (for all crystal/resonator device oscillator modes). Prescaler A circuit that slows the rate of a clocking source to a counter/timer. Program Bus The bus which is used to transfer instruction words form the program memory to the CPU. Program Counter A register which specifies the address in program memory that is the next instruction to execute. Program Memory Any memory that is one the program memory bus. Static variables may be contained in program memory (such as tables). PSP See Parallel Slave Port. Pulse Width Modulation (PWM) A serial signal in which the information is contained in the width of a (high) pulse of a constant frequency signal. A PWM output, from the CCP module, of the same duty cycle requires no software overhead. PUSH A termed used to refer to the action of saving information onto a stack (software and/or hardware). See POP. 35 PWM Glossary Pulse Width Modulation. 1997 Microchip Technology Inc. DS31035A-page 35-9 PICmicro MID-RANGE MCU FAMILY Q Q-cycles This is the same as a device oscillator cycle. There are 4 Q-cycles for each instruction cycle. R RC Resistor-Capacitor. The default configuration for the device oscillator. This allows a "Real-Cheap" implementation for the device clock source. This clock source does not supply an accurate time-base. Operation to 4 MHz is supported. (See EXTRC). Read-Modify-Write This is where a register is read, then modified, and then written back to the original register. This may be done in one instruction cycle or multiple instruction cycles. Register File This is the Data Memory. Contains the SFRs and GPRs. ROM Read Only Memory. Memory that is fixed and cannot be modified. DS31035A-page 35-10 1997 Microchip Technology Inc. Glossary S Sampling Time Sampling time is the complete time to get an A/D result. It includes the acquisition time and the conversion time. Serial Peripheral Interface (SPI) This is one of the modes of the SSP module. This is typically a 3-wire interface, with a data out line, a data in line, and a clock line. Since the clock is present, this is a synchronous interface. SFR Special Function Register. These registers contain the control bits and status information for the device. Single cycle instruction An instruction that executes in a "single" machine cycle (TCY). Sleep This is the low power mode of the device, where the device's oscillator is disabled.This reduces the current the device consumes. Certain peripherals may be placed into modes where they continue to operate. Special Function Registers (SFR) These registers contain the control bits and status information for the device. SPI See Serial Peripheral Interface. Stack A portion of the CPU which retains the return address for program execution. The stack gets loaded with the value in the Program Counter when a CALL instruction is executed or an interrupt occurs. 35 Glossary 1997 Microchip Technology Inc. DS31035A-page 35-11 PICmicro MID-RANGE MCU FAMILY T TAD In the A/D Converter, the time for a single bit of the analog voltage to be converted to a digital value. TCY The time for an instruction to complete. This time is equal to Fosc/4 and is divided into four Q-cycles. Tosc The time for the device oscillator to do a single period. U USART Universal Synchronous Asynchronous Receiver Transmitter. This module can either operate as a full duplex asynchronous communications port, or a half duplex synchronous communications port. When operating in the asynchronous mode, this can be interfaced to a PC's serial port. DS31035A-page 35-12 1997 Microchip Technology Inc. Glossary V Voltage Reference (VREF) A voltage level that can be used as a reference point for A/D conversions (AVDD and AVSS) or the trip point for comparators. von Neumann Architecture In this architecture the Program Memory and Data Memory are contained in the same area. This means that accesses to the program memory and data memory must occur sequentially, which affects the performance of the device. W W Register See Working Register. Watchdog Timer (WDT) Used to increase the robustness of a design by recovering from software flows that were not expected in the design of the product or other system related issues. The Watchdog Timer causes a reset if it is not cleared prior to overflow. The clock source for a PICmicro is an on-chip RC oscillator which enhances system reliability. WDT Watchdog Timer. Working Register (W) Can also be thought of as the accumulator of the device. Also used as an operand in conjunction with the ALU during two operand instructions. X XT One of the device oscillator modes. Used for operation from 100 kHz to 4 MHz. 35 Glossary 1997 Microchip Technology Inc. DS31035A-page 35-13 PICmicro MID-RANGE MCU FAMILY 35.1 Revision History Revision A This is the initial released revision of the Glossary. DS31035A-page 35-14 1997 Microchip Technology Inc. M WORLDWIDE SALES AMERICAS ASIA/PACIFIC EUROPE Corporate Office Hong Kong United Kingdom Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602-786-7200 Fax: 602-786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com Microchip Asia Pacific RM 3801B, Tower Two Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431 Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-1189-21-5858 Fax: 44-1189-21-5835 Atlanta India France Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Microchip Technology Inc. India Liaison Office No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062 Arizona Microchip Technology SARL Zone Industrielle de la Bonde 2 Rue du Buisson aux Fraises 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Korea Germany Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Munchen, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Shanghai Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-39-6899939 Fax: 39-39-6899883 Boston Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575 Chicago Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas Microchip Technology Inc. 14651 Dallas Parkway, Suite 816 Dallas, TX 75240-8809 Tel: 972-991-7177 Fax: 972-991-8588 Dayton Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Los Angeles Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 714-263-1888 Fax: 714-263-1338 New York Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan'an Road West, Hong Qiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060 Singapore Microchip Technology Taiwan Singapore Branch 200 Middle Road #07-02 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850 Taiwan, R.O.C Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886 2-717-7175 Fax: 886-2-545-0139 Italy JAPAN Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa 222 Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 10/31/97 Microchip Technology Inc. 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 516-273-5305 Fax: 516-273-5335 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Toronto Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253 1997 Microchip Technology Inc. DS33023A PICmicro MID-RANGE MCU FAMILY M Printed in the USA, 12/97 All rights reserved. (c) 12/11/97, Microchip Technology Incorporated * 2355 W. Chandler Blvd. * Chandler, AZ USA * 602-786-7200 * FAX: 602-899-9210 DS33023A 1997 Microchip Technology Inc.