WPEQ-353ACNI 802.11ac/abgn Dual-Band 3T3R Military Temp Mini PCIe Module Industrial Wi-Fi transceiver for Military Temp Solution The WPEQ-353ACNI is powered by Qualcomm Atheros radio chip and features 3x3 11ac/abgn technology for higher throughput performance, reliability and range. It is reliable design for outdoor and rugged environments. High interference immunity for Wi-Fi congested environment and regulatory modular certifications to expedite system integration. Key Feature : Embedded Application : Military Temp Range: -40C ~ +85C Application included outdoor Access point , Aviation , Vehicle -mount computer , Traffic controller , Factory Automation ,Fleet management , Outdoor surveillance, Qualcomm Atheros QCA9890-BR4B Data Rates: allows link speeds up to 1.3Gbps Support Linux driver Medical device ,Industrial 4.0,etc. Specification : Standards: Chipset: Data Rate: Operating Voltage: Operating Temperature Range: Humidity (Non-Condensing): Power Consumption: IEEE 802.11ac/abgn (3T3R) Qualcomm Atheros QCA9890-BR4B 802.11b: 11Mbps / 802.11a/g: 54Mbps / 802.11n: 450Mbps / 802.11ac: 1.3Gbps IEEE 802.11 ac/abgn ISM Band, 2.412GHz ~ 2.472GHz, 5.1500MHz ~ 5.825MHz *Subject to local regulations Mini PCI Express Mini PCI-e 3 x UFL connector for 3T3R 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11a/g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11ac: OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM) 3.3V 9% I/O supply voltage -40C ~ +85C Operating Humidity (non-condensing): 10% ~ 85% Storage Humidity (non-condensing): 5% ~ 90% TX Mode: 1250mA / RX Mode: 350mA Dimension (in mm): Weight (g): Driver Support: Security 50.8 x 29.85 x 3.95mm 8g Linux 64/128-bits WEP, WPA, WPA2, 802.1x Operating Frequency: Interface: Form Factor: Antenna: Modulation: WPEQ-353ACNI Ver.1.2 OUTPUT POWER & SENSITIVITY 802.11g Data Rate Tx 2dBm Rx Sensitivity 54Mbps 15dBm -75dBm 802.11n / 2.4GHz HT20 HT40 Data Rate Tx 2dBm (1TX) Tx 2dBm (3TX) Rx Sensitivity MCS7 13dBm 18dBm -72dBm MCS7 13dBm 18dBm -68dBm 802.11a Data Rate Tx 2dBm Rx Sensitivity 54Mbps 15dBm -73dBm 802.11n / 5GHz HT20 HT40 Data Rate Tx 2dBm (1TX) Tx 2dBm (3TX) Rx Sensitivity MCS7 13dBm 18dBm -70dBm MCS7 12dBm 17dBm -68dBm 802.11ac VHT80 Data Rate Tx 2dBm (1TX) Tx 2dBm (3TX) Rx Sensitivity MCS9 10dBm 15dBm -57dBm WPEQ-353ACNI Ver.1.2 Block Diagram 1 2 4 3 REVISION HISTOR REV. MARK EC/DC MEMO T01 FIR Mechanical Dimension (mm) WPEQ-353ACNI Ver.1.2 Pin Assignment Pin# Pin Name 1 WAKE_L(NA) 3 No Connection 5 Description Output and open Drain active Low signal. This signal is used to request that the system return from a sleep/suspended state to service a function initiated wake event. Pin# Pin Name Description 2 +3.3V +3.3V - 4 GND GND No Connection - 6 No Connection - 7 CLKREQ_L Output for reference clock request signal 8 No Connection - 9 GND GND 10 No Connection - 11 REFCLK- Input signal for PCI Express differential reference clock (100 MHz) 12 No Connection - 13 REFCLK+ Input signal for PCI Express differential reference clock (100 MHz) 14 No Connection - 15 GND GND 16 No Connection - 17 No Connection - 18 GND GND Input and active low signal. This signal is used by the system to disable radio operation on add-in cards that implement radio frequency applications. When implemented, this signal requires a pull-up resistor on the card. Input signal for functional reset to the card 19 No Connection - 20 W_DISABLE_L 21 GND GND 22 PERST_L 23 PERn0 24 +3.3V +3.3V 25 PERp0 26 GND GND 27 GND GND 28 No Connection - 29 GND GND 30 No Connection - PCI Express x1 data interface: one differential receive pair PCI Express x1 data interface: one differential receive pair WPEQ-353ACNI Ver.1.2 Pin Assignment Pin# Pin Name 31 PETn0 33 PETp0 35 GND 37 Description PCI Express x1 data interface: one differential transmit pair PCI Express x1 data interface: one differential transmit pair Pin# Pin Name Description 32 No Connection - 34 GND GND GND 36 No Connection - GND GND 38 No Connection - 39 No Connection - 40 GND GND 41 No Connection - 42 No Connection - 43 GND GND 44 LED_WLAN_L (OPT) Output and open drain active low signal. This signal is used to allow the PCI Express Mini Card add-in card to provide status indicators via LED devices that will be provided by the system 45 No Connection - 46 No Connection - 47 No Connection - 48 No Connection - 49 No Connection - 50 GND GND 51 No Connection - 52 +3.3V +3.3V *NANo active, OPT Optional WPEQ-353ACNI Ver.1.2