WPEQ-353ACNI
802.11ac/abgn Dual-Band
3T3R Military Temp Mini PCIe Module
Industrial Wi-Fi transceiver for Military Temp Solution
The WPEQ-353ACNI is powered by Qualcomm Atheros radio chip and features 3x3 11ac/abgn technology for
higher throughput performance, reliability and range. It is reliable design for outdoor and rugged environments.
High interference immunity for Wi-Fi congested environment and regulatory modular certifications to expedite
system integration. Key Feature :
Military Temp Range: -40°C ~ +85°C
Qualcomm Atheros QCA9890-BR4B
Data Rates: allows link speeds up to 1.3Gbps
Support Linux driver
Embedded Application :
Application included outdoor Access point , Aviation ,
Vehicle -mount computer , Traffic controller , Factory
Automation ,Fleet management , Outdoor surveillance,
Medical device ,Industrial 4.0,etc.
Standards:
IEEE 802.11ac/
abgn (3T3R)
Chipset:
Qualcomm
Atheros QCA9890-BR4B
Data Rate:
802.11b: 11Mbps / 802.11a/g: 54Mbps / 802.11n: 450Mbps / 802.11ac:
1.3Gbps
Operating Frequency:
IEEE 802.11 ac/
abgn ISM Band, 2.412GHz ~ 2.472GHz, 5.1500MHz ~ 5.825MHz
*Subject to local regulations
Interface:
Mini PCI Express
Form Factor:
Mini PCI
-e
Antenna:
3 x UFL connector for 3T3R
Modulation:
802.11b: DSSS (DBPSK, DQPSK, CCK)
802.11a/g: OFDM (BPSK, QPSK, 16
-QAM, 64-QAM)
802.11n: OFDM (BPSK, QPSK, 16
-QAM, 64-QAM)
802.11ac:
OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM)
Operating Voltage:
3.3V
±9% I/O supply voltage
Operating Temperature Range:
-
40°C ~ +85°C
Humidity
(Non
-Condensing):
Operating Humidity (non
-condensing): 10% ~ 85%
Storage Humidity (non
-condensing): 5% ~ 90%
Power Consumption:
TX Mode: 1250mA / RX Mode: 350mA
Dimension (in mm):
50.8 x 29.85 x 3.95mm
Weight
(g):
8g
Driver Support:
Linux
Security
64/128
-bits WEP, WPA, WPA2, 802.1x
Specification :
WPEQ-353ACNI
Ver.1.2
WPEQ-353ACNI
Ver.1.2
802.11a
Data Rate Tx ±2dBm Rx Sensitivity
54Mbps 15dBm -73dBm
802.11n / 5GHz
HT20 Data Rate Tx ±2dBm (1TX) Tx ±2dBm (3TX) Rx Sensitivity
MCS7 13dBm 18dBm -70dBm
HT40 MCS7 12dBm 17dBm -68dBm
OUTPUT POWER & SENSITIVITY
802.11g
Data Rate Tx ±2dBm Rx Sensitivity
54Mbps 15dBm -75dBm
802.11n / 2.4GHz
HT20 Data Rate Tx ±2dBm (1TX) Tx ±2dBm (3TX) Rx Sensitivity
MCS7 13dBm 18dBm -72dBm
HT40 MCS7 13dBm 18dBm -68dBm
802.11ac
VHT80 Data Rate Tx ±2dBm (1TX) Tx ±2dBm (3TX) Rx Sensitivity
MCS9 10dBm 15dBm -57dBm
Block Diagram
Mechanical Dimension (mm)
WPEQ-353ACNI
Ver.1.2
TOLERANCE (UNLESS OTHERWISE SPEC.)
0 ~ 29.99
120.0 ~ 299.99
300 or GREATER
ANGULAR TOL.
0.40
0.20
0.15
0.10
30.0 ~ 119.99
THIRD ANGLE
PROJECTION
MODEL NAME :
UNIT SCALE SIZE SHEET REV.
DWG TITLE :
DWG / PART NO.
INFORMATION CONTAINED ON ALL SHEETS OF THIS PRINT
CAN NOT BE REPRODUCED OR USED, IN WHOLE OR IN
PART, WITHOUT GEMTEK'S CONSENT. THIS NOTICE DOES
NOT IMPLY PUBLICATION.
DESIGNED BY:
DRAWN BY:
APPROVED BY:
0.50
D
B
A
6
54
3
1COMPUTER GENERATED PRINT
DO NOT SCALE, DO NOT REVISE MANUALLY
C
6
54
3
12
D
B
A
C
REV. MARK DESCRIPTION SIGNATURE
REVISION HISTORY - ALL SHEETS ARE THE SAME REVISION STATUS
EC/DC MEMO
Stanley Jiang
Stanley Jiang
T01
WMIQ-287ACN 1/1
A41.000MM
Appearence Dimension Drawing
STANLEY JIANG
2014-09-23
FIRST RELEASE.
T01
Pin Assignment
Pin#
Pin Name Description
Pin#
Pin Name Description
1
WAKE_L(NA)
Output and open Drain
active Low signal. This
signal is used to request
that the system return
from a sleep/suspended
state to service a function
initiated wake event.
2
+3.3V
3
No Connection
-
4
GND
5
No Connection
-
6
-
7
CLKREQ_L
Output for reference clock
request signal
8
-
9
GND
GND
10
-
11
REFCLK
-
Input signal for PCI Express
differential reference clock
(100 MHz)
12
-
13
REFCLK+
Input signal for PCI Express
differential reference clock
(100 MHz)
14
-
15
GND
GND
16
-
17
No Connection
-
18
GND
19
No Connection
-
20
Input and active low signal.
This signal is used by the
system to disable radio
operation on add
-
in cards that
implement radio frequency
applications.
When implemented, this
signal requires a pull
-up
resistor on the card.
21
GND
GND
22
Input signal for functional
reset to the card
23
PERn0
PCI Express x1 data
interface: one differential
receive pair
24
+3.3V
25
PERp0
PCI Express x1 data
interface: one differential
receive pair
26
GND
27
GND
GND
28
-
29
GND
GND
30
-
WPEQ-353ACNI
Ver.1.2
Pin Assignment
Pin#
Pin Name Description
Pin#
Pin Name Description
31
PETn0
PCI Express x1 data
interface: one differential
transmit pair
32
No Connection
-
33
PETp0
PCI Express x1 data
interface: one differential
transmit pair
34
GND
GND
35
GND
GND
36
No Connection
-
37
GND
GND
38
No Connection
-
39
No Connection
-
40
GND
GND
41
No Connection
-
42
No Connection
-
43
GND
GND
44
LED_WLAN_L
(OPT)
Output and open drain active
low signal. This signal is used
to allow the PCI Express Mini
Card add
-in card to provide
status indicators via LED
devices that will be provided
by the system
45
No Connection
-
46
No Connection
-
47
No Connection
-
48
No Connection
-
49
No Connection
-
50
GND
GND
51
No Connection
-
52
+3.3V
+3.3V
WPEQ-353ACNI
Ver.1.2
*NANo active, OPT Optional