5305 Spectrum Drive, Frederick, MD 21703-7362 TEL: 301-846-9222, 800-638-2048 Fax: 301-846-9116
web: www.weinschel.com email: sales@weinschel.com
148
4/30/02
Specifications
NOMINAL IMPEDANCE: 50
FREQUENCY RANGE: 10 MHz to 2.5 GHz
CELL CONFIGURATIONS:
Model NO. Attenuation Cell
Number Cells Range/Steps Increments
(dB) (dB)
4208-63.75 8 63.75/0.25 0.25, 0.5, 1, 2, 4, 8,
16, 32
4206-63 6 63/1 1, 2,4, 8, 16, 32
*POWER RATING (Undirectional):
Model J1 J2
4206-XX 4 Watts MAX IN 2 Watts MAX IN
(+36 dBm) (+33 dBm)
4208-XX 2 Watts MAX IN 4 Watts MAX IN
(+33 dBm) (+36 dBm)
MAXIMUM SWR:
Frequency Range (GHz) SWR
0.01 - 0.07 1.60
0.07 - 2.5 1.40
Frequency Range (GHz) 4208-63.75 4206-63
0.01 - 1.0 8.50 7.00
1.0 - 2.0 11.50 9.00
2.0 - 2.5 13.00 10.00
MONOTONICITY: 10 MHz to 2.5 GHz
3rd ORDER INTERMODULATION (IM3): -30 dBm typical,
measured with two +27 dBm tones @ 869 MHz (f1) and
894 MHz (f2), the IM3 frequeny being 847 MHz (2fl-f2).
IP3 (input) = +53 dBm
The input IP3 is derived from the following relationship:
IP3 = 3(Pin-
α
)-IM3 +
α
where α= the insertion loss (dB) at the IM3 frequency;
Pin=single tone input power (dBm).
INSERTION LOSS, Maximum (dB):
Features
Ideal for use in Wireless/Cellular, RF imulation/Emulation, &
Communication Test Applications.
oBroadband Performance - 10 MHz to 2.5 GHz
usable dc to 10 MHz with reducded specifications
oHigh IP3 and High Power Rating
- Utilizes MESFET Switching
oFlexible DC Voltage (+5 to +15 V)
oLow DC Power Consumption - Ideal for portable
battery powered equipment.
oCustom Configurations including bus controlled
attenuator subsystems
2
INCREMENTAL ATTENUATION ACCURACY:
Frequency Accuracy
Range (GHz)
0.01 - 2.5 + 0.4 dB or 2.0%
SWITCHING TIME: 5 µsec. maximum
OPERATING VOLTAGE: + 5 to +15 V
OPERATING CURRENT: 25 mA typical
TEMPERATURE RANGE (Operating): 0°C to +70°C
TEMPERATURE COEFFICIENT: <0.002/dB/dB/°C
CONNECTORS: SMA female connectors - mate nonde-
structively with MIL-C-39012 connectors.
CONTROL CONNECTOR: AMP-Latch 10 pin ribbon cable
connector mates with AMP P/N 746285-1 (supplied with
each unit)
WEIGHT: 4206-X 160 g (5.6 oz)
4208-X 220 g (7.7 oz)
CONTROL CONFIGURATION: Units are supplied with a
built-in TTL interface. Each unit is supplied with a mating 10
pin connector (Amp 746285-1). Refer to Physical
Dimensions for mating connector pin/wiring details. Two
wires are specified for supply voltage and ground. The
remaining wires will accept TTL control signals to activate
or de-activate a particular attenuation cell. A TTL high will
energize a cell to the high attenuation state, whereas a TTL
low will maintain a cell in its zero attenuation state.
Model 4206 & 4208 10 MHz to 2.5 GHz
High Power Solid-State *2 Watts
Programmable Attenuators
High IP3
5305 Spectrum Drive, Frederick, MD 21703-7362 TEL: 301-846-9222, 800-638-2048 Fax: 301-846-9116
web: www.weinschel.com email: sales@weinschel.com
149
4/30/02
J1 J2
PHYSICAL DIMENSIONS:
Models 4206 & 4208:
TTL Conn 4206-63 4208-63.75
PIN No. (J3) dB (Cell) dB (Cell)
1 1 0.25
2 2 0.50
341
482
5164
6328
7NC16
8NC32
9 +5 to 15V +5 to 15V
10 COM COM
NC = Not Connected
Control Connector J3 Pin Locations:
Model No. A B C
4206-X 09.0 (4.33) 96.5 (3.80) 76.2 (3.00)
4208-X 143.5 (5.65) 110.2 (4.34) 110.2 (4.34)
NOTE: All dimensions are given in mm (inches) and are
maximum, unless otherwise specified.