STTH15AC06C Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description A1 The STTH15AC06C uses ST Turbo 2 600 V technology and is suited as a boost diode in air conditioning equipment for continuous mode interleaved power factor correction. K A2 K The device is also intended for use as a freewheeling diode in power supplies and other power switching applications. A1 K A2 TO-220AB STTH15AC06CT A1 A2 K TO-220FPAB STTH15AC06CFP Features * Ultrafast switching Table 1. Device summary Symbol Value IF(AV) 2 x 7.5 A VRRM 600 V trr (max) 25 ns VF (max) 1.5 V Tj (max) 175 C * Low reverse recovery current * Reduces switching and conduction losses * Low thermal resistance * insulated package TO-220FPAB: - Insulated voltage: 2500 VDC October 2013 This is information on a product in full production. DocID024884 Rev 1 1/11 www.st.com 11 Characteristics 1 STTH15AC06C Characteristics Table 2. Absolute ratings (limiting values per diode at 25 C, unless otherwise specified) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 600 V IF(RMS) Forward rms current 15 A IF(AV) Average forward current IFSM Surge non repetitive forward current Tstg Storage temperature range Tj Per diode 7.5 Per device 15 A tp = 10 ms sinusoidal 80 A -65 to +175 C 175 C Maximum operating junction temperature Table 3. Thermal parameters Symbol Parameter Value Per diode 2.8 Total 1.7 Unit Junction to case (TO-220AB) Coupling (TO-220AB) 0.6 Rth(j-c) C/W Per diode 6 Junction to case (TO-220FPAB) Total 4.5 Coupling (TO-220FPAB) 3 Table 4. Static electrical characteristics (per diode) Symbol IR(1) Parameter Reverse leakage current Test conditions Tj = 25 C Tj = 150 C Tj = 25 C VF(2) Forward voltage drop Tj = 150 C Tj = 25 C Tj = 150 C Min. Max. Unit 1 VR = VRRM A 10 100 1.9 IF = 7.5A 1.15 1.50 V 2.2 IF = 15A 1. Pulse test: tp = 5 ms, < 2% 2. Pulse test: tp = 380 s, < 2% To evaluate the conduction losses use the following equation: P = 1.2 x IF(AV) + 0.04 IF2(RMS) 2/11 Typ. DocID024884 Rev 1 1.4 1.8 STTH15AC06C Characteristics Table 5. Dynamic characteristics (per diode) Symbol trr Test conditions Parameter Reverse recovery time IRM Reverse recovery current tfr IF = 0.5 A, Irr = 0.25 A, IR= 1 A Tj = 25 C Forward recovery voltage 50 Tj = 125 C IF = 7.5 A, VR = 400 V, dIF/dt = -100 A/s 3.7 5 A IF = 7.5 A, VFR = 1.5 V, dIF/dt = 100 A/s 100 ns Tj = 25 C d = 0.1 d = 0.2 100.0 d=1 d = 0.5 2.5 V Figure 2. Forward voltage drop versus forward current (typical values, per diode) PF(AV)(W) d = 0.05 ns 35 Figure 1. Average forward power dissipation versus average forward current (per diode) 16 14 25 IF = 1 A, VR = 30 V, dIF/dt = -50 A/s Forward recovery time VFP Min. Typ. Max. Unit I F ( A) 12 10.0 10 8 T j = 150 C T j = 25 C 6 1.0 4 T 2 IF(AV)( A) 0 0 1 2 3 4 5 6 7 0.1 8 9 Figure 3. Forward voltage drop versus forward current (maximum values, per diode) 100.0 I F ( A) 10.0 T j = 150 C T j = 25 C 1.0 0.1 V F (V) tp d=tp/T V F (V) 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 Figure 4. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220AB) Z th ( j-c) /R th ( j-c) 1.0 0.9 TO- 220AB 0.8 0.7 0.6 0.5 Single pulse 0.4 0.3 0.2 0.1 0.0 1.E-04 1.E-03 DocID024884 Rev 1 tP(s) 1.E-02 1.E-01 1.E+00 3/11 Characteristics STTH15AC06C Figure 5. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220FPAB) Z th ( j-c) /R th ( j-c) 1.0 0.9 TO- 220FPAB 0.8 0.7 0.6 0.5 Single pulse 0.4 0.3 0.2 0.1 tP(s) 0.0 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 Figure 7. Reverse recovery time versus dIF/dt (typical values, per diode) 400 tRR(ns) I F = 7.5 A V R = 400 V Tj = 125 C 300 250 200 I F = 7.5 A V R = 400 V Tj = 125 C 10 8 6 4 2 dIF/dt(A/s) 0 0 50 100 150 200 250 300 350 400 450 500 Figure 8. Reverse recovery charges versus dIF/dt (typical values, per diode) QRR(nC) I F = 7.5 A V R = 400 V Tj = 125 C 500 400 300 150 200 100 100 50 dIF/dt(A/s) 0 IRM (A) 12 600 350 0 0 50 100 150 200 250 300 350 400 450 500 SFACTOR I F = 7.5 A V R = 400 V Tj = 125 C 50 100 150 200 250 300 350 400 450 500 Figure 10. Relative variations of dynamic parameters versus junction temperature 2.0 2.5 dIF/dt(A/s) 0 Figure 9. Reverse recovery softness factor versus dIF/dt (typical values, per diode) 3.0 Figure 6. Peak reverse recovery versus dIF/dt (typical values, per diode) S FACTOR I F = 30 A; VR = 400 V Reference: Tj = 125 C 1.5 2.0 1.0 1.5 I RM 1.0 0.5 0.5 dIF/dt(A/s) 0.0 0.0 0 4/11 50 100 150 200 250 300 350 400 450 500 Q RR 25 DocID024884 Rev 1 50 Tj (C) 75 100 125 STTH15AC06C Characteristics Figure 11. Transient peak forward voltage versus dIF/dt (typical values, per diode) 12 10 VFP(V) Figure 12. Forward recovery time versus dIF/dt (typical values, per diode) 160 I F = 7.5 A Tj = 125 C I F = 7.5 A V R = 1.5 V Tj = 125 C 140 120 8 100 6 80 4 60 40 2 0 tFR(ns) 20 dIF/dt(A/s) 50 100 150 200 250 300 350 400 450 500 0 dIF/dt(A/s) 50 100 150 200 250 300 350 400 450 500 Figure 13. Junction capacitance versus reverse voltage applied (typical values, per diode) 100 C(pF) F = 1 MHz VOSC = 30 mVRMS Tj = 25 C 10 1 VR(V) 1 10 100 DocID024884 Rev 1 1000 5/11 Package information 2 STTH15AC06C Package information * Epoxy meets UL94, V0 * Cooling method: by conduction (C) * Recommended torque: 0.4 to 0.6 N*m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 14. TO220AB dimension definitions A E P Resin gate 0.5 mm max. protrusion(1) F Q H1 D D1 L30 L20 b1 J1 L1 L b e e1 Resin gate 0.5 mm max. protrusion(1) (1) Resin gate position accepted in each of the two position shown as well as the symmetrical opposites 6/11 DocID024884 Rev 1 c STTH15AC06C Package information Table 6. TO220AB dimension values Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.40 4.60 0.17 0.18 b 0.61 0.88 0.024 0.035 b1 1.14 1.70 0.045 0.067 c 0.48 0.70 0.019 0.027 D 15.25 15.75 0.60 0.62 D1 1.27 typ 0.05 typ. E 10 10.40 0.39 0.41 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.19 0.20 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.24 0.26 J1 2.40 2.72 0.094 0.107 L 13 14 0.51 0.55 L1 3.50 3.93 0.137 0.154 L20 16.40 typ 0.64 typ. L30 28.90 typ 1.13 typ. P 3.75 3.85 0.147 0.151 Q 2.65 2.95 0.104 0.116 DocID024884 Rev 1 7/11 Package information STTH15AC06C Figure 15. TO220FPAB dimension definitions A B H Dia L6 L2 L7 L3 L5 F1 L4 F2 F G1 G 8/11 D DocID024884 Rev 1 E STTH15AC06C Package information Table 7. T0-220FPAB dimension values Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 F2 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 DocID024884 Rev 1 9/11 Ordering information 3 STTH15AC06C Ordering information Table 8. Ordering information 4 Order code Marking Package Weight Base qty Delivery mode STTH15AC06CT STTH15AC06CT TO-220AB 1.9 g 50 Tube STTH15AC06CFP STTH15AC06CFP TO-220FPAB 2.0 g 50 Tube Revision history Table 9. Document revision history 10/11 Date Revision 21-Oct-2013 1 Changes First release. DocID024884 Rev 1 STTH15AC06C Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER'S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR "AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL" INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID024884 Rev 1 11/11 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: STTH15AC06CFP STTH15AC06CT