QP27C64
March 9, 2009
2945 Oakmead Village Ct, Santa Clara, CA 95051 Phone: (408) 737-0992 Fax: (408) 736—8708 Internet: www.qpsemi.com
QP27C64 – 64 Kilobit (8K x 8) CMOS EPROM
General Description
The QP27C64 is an 8Kx8 (64-Kbit), UV erasable programmable read-only memory. It operates from a single +5 V
supply, has a static standby mode, and features fast single address location programming. The QP27C64 meets the
same specification requirements and utilizes the same programming methodology as the AMD 27C64 that it replaces.
Products are available in windowed and non-windowed (OTP) ceramic hermetic packages, as well as plastic one time
programmable (OTP) packages.
Data is typically accessed in less than 45 ns, allowing high-performance microprocessors to operate without any WAIT
states. The device offers separate Output Enable ( OE ) and Chip Enable ( CE ) pins, eliminating bus contention in a
multiple bus system.
Typical power consumption is only 80 mW in active mode, and 100 μW in standby mode.
All signals are TTL levels, including programming signals. Bit locations may be programmed singly, in blocks, or at
random. The device is programmed identically to the AMD27C64 device that it replaces, using the same programming
algorithm (100 us pulses).
The QP27C64 features:
- Same programming algorithm as the AMD27C64, allowing it to be programmed using the same equipment,
data and algorithm. When programming this device select AMD as the manufacturer and 27C64 as the
devicetype.
- Speed options as fast as 45ns
- JEDEC Pinout
- Single +5V power supply
- CMOS and TTL input/output compatibility
- Two line control functions
The device/family is constructed using an advanced UV CMOS wafer fabrication process.
Block Diagram
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 2 of 8
Pin Name Function
A0 – A12 Address Inputs
CE (E) Chip Enable Input
DQ0 – DQ7 Data Input/Output
OE (G) Output Enable Input
PGM (P) Program Enable Input
VCC V
CC Supply Voltage
VPP Program Voltage Input
NC No Internal Connection
Connection Diagrams
CERDIP / CERPACK / PDIP LCC / PLCC
Device Type
Functional Description
Device Erasure
In order to clear all locations of their programmed contents, the device must be exposed to an ultraviolet light source. A
dosage of 15 W seconds/cm2 is required to completely erase the device. This dosage can be obtained by exposure to
an ultraviolet lamp with a wavelength of 2537Å and an intensity of 12,000 μW/cm2 for 15 to 20 minutes. The device
should be directly under and about one inch from the source, and all filters should be removed from the UV light source
prior to erasure.
Note that all UV erasable devices will erase with light sources having wavelengths shorter than 4000Å, such as
fluorescent light and sunlight. Although the erasure process happens over a much longer time period, exposure to any
light source should be prevented for maximum system reliability. Simply cover the package window with an opaque
label or substance.
Device Programming
Upon delivery, or after each erasure, the device has all of its bits in the “ONE”, or HIGH state. “ZEROs” are loaded into
the device through the programming procedure.
The device enters the programming mode when 12.75V ± 0.25V is applied to the VPP pin, and both CE & PGM are at
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 3 of 8
VIL.
For programming, the data to be programmed is applied 8 bits in parallel to the data pins.
The programming algorithm uses a 100 μs programming pulse and gives each address only as many pulses as needed
to reliably program the data. After each pulse is applied to a given address, the data in that address is verified. If the
data does not verify, additional pulses are given until it verifies or the maximum pulses allowed is reached. This process
is repeated while sequencing through each address of the device. This part of the algorithm is done with VCC = 6.25 V to
assure that each bit is programmed to a sufficiently high threshold voltage. After the final address is completed, the
entire EPROM memory is verified at VCC = VPP = 5.25 V.
Program Inhibit
Programming different data to multiple devices in parallel is easily accomplished. Except for CE , all like inputs of the
devices may be common. A TTL low-level program pulse applied to one device’s CE input with VPP = 12.75 V ± 0.25 V
and PGM LOW will program that particular device. A high-level CE input inhibits the other devices from being
programmed.
Program Verify
Verification should be performed on the programmed bits to determine that they were correctly programmed. Verify
should be performed with OE and CE at VIL, PGM at VIH, and VPP between 12.5 V and 13.0 V.
Autoselect Mode
The autoselect mode provides manufacturer and device identification through identifier codes on DQ0–DQ7. This mode
is primarily intended for programming equipment to automatically match a device to be programmed with its
corresponding programming algorithm. This mode is functional in the 25°C ± 5°C ambient temperature range that is
required when programming the device. To activate this mode, the programming equipment must force VH on address
line A9. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH
(that is, changing the address from 00h to 01h). All other address lines must be held at VIL during the autoselect mode.
Byte 0 (A0 = VIL) represents the manufacturer code, and Byte 1 (A0 = VIH), the device identifier code. Both codes have
odd parity, with DQ7 as the parity bit.
Read Mode
To obtain data at the device outputs, Chip Enable ( CE ) and Output Enable ( OE ) must be driven low. CE controls the
power to the device and is typically used to select the device. OE enables the device to output data, independent of
device selection. Addresses must be stable for at least tACC–tOE.
Standby Mode
The device enters the CMOS standby mode when CE is at VCC ± 0.3 V. Maximum VCC current is reduced to 100 μA.
The device enters the TTL-standby mode when CE is at VIH. Maximum VCC current is reduced to 1.0 mA. When in
either standby mode, the device places its outputs in a high-impedance state, independent of the OE input.
Output OR Connection
To accommodate multiple memory connections, a two-line control function provides:
Low memory power dissipation
Assurance that output bus contention will not occur.
CE should be decoded and used as the primary device selecting function, while OE be made a common connection
to all devices in the array and connected to the READ line from the system control bus. This assures that all deselected
memory devices are in their low-power standby mode and that the output pins are only active when data is desired from
a particular memory device.
System Applications
During the switch between active and standby conditions, transient current peaks are produced on the rising and falling
edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading
of the device. As a minimum, a 0.1μF ceramic capacitor (high frequency, low inductance) should be used on each
device between VCC and VSS to minimize transient effects. In addition, to overcome the voltage drop caused by the
inductive effects of the printed circuit board traces on EPROM arrays, a 4.7μF bulk electrolytic capacitor should be used
between VCC and VSS for each eight devices. The location of the capacitor should be close to where the power supply is
connected to the array.
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 4 of 8
MODE Select Table
Mode CE OE PGM A0 A9 VPP Outputs Notes
Read VIL V
IL X X X X DOUT \1
Output Disable X VIH X X X X High Z \1
Standby (TTL) VIH X X X X X High Z \1
Standby (CMOS) VCC±0.3V X X X X X High Z \1
Program VIL X VIL X X VPP DIN \1
Program Verify VIL V
IL V
IH X X VPP DOUT \1
Program Inhibit VIH X X X X VPP High Z \1
Manufacturer Code VIL V
IL X VIL V
H X 01h \1 \2 \3 \4
Device Code VIL V
IL X VIH V
H X 15h \1 \2 \3 \4
Notes:
\1 X = Either VIH or VIL
\2 VH = 12.0V ± 0.5V
\3 A1-A8 & A10-A12 = VIL
\4 Device Manufacture Code and Device ID match original AMD device for programming compatibility
Absolute Maximum Ratings
Stresses above the AMR may cause permanent damage, extended operation at AMR may degrade performance and affect reliability
Condition Units Notes
Power Supply (VCC) -0.6 to +7.0 Volts DC
Voltage with Respect to VSS
All pins except A9, VPP, VCC -0.6 to VCC+0.6 Volts \5 \9
A
9 and VPP -0.6 to 14 Volts \6 \9
Storage Temperature Range -65 to +150 ºC \7
Lead Temperature (soldering, 10 seconds) +300 ºC
Junction Temperature (TJ) +150 ºC \7
Maximum Operating Temperature
Commercial Devices 0 to 70 ºC \7 \8
Industrial Devices -40 to 85 ºC \7 \8
Military Temperature Range -55 to 125 ºC \7 \8
Data Retention 10 Years, minimum
Device must not be removed from or inserted into a socket when VCC or VPP is applied.
Recommended Operating Conditions
Condition Units Notes
Supply Voltage Range (VCC) 4.5 to 5.5 Volts DC
Input or Output Voltage Range 0.0 to VCC Volts DC \5 \6
Minimum High-Level Input Voltage (VIH) 2.0 Volts DC
Maximum Low-Level Input Voltage (VIL) 0.8 Volts DC
Case Operating Range (Tc)
Commercial Devices 0 to 70 ºC \7 \8
Industrial Devices -40 to 85 ºC \7 \8
Military Temperature Range -55 to 125 ºC \7 \8
\5 – Minimum DC Input Voltage on input or I/O pins –0.5V. During voltage transitions, the input may overshoot VSS to –
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 5 of 8
2.0V for periods of up to 20ns. Maximum DC voltage on input and I/O pins is VCC+0.5V. During transitions, input
and I/O pins may overshoot to VCC +2.0V for periods up to 20ns.
\6 – Minimum DC Input Voltage on A9 is –0.5V. During voltage transitions, A9 and VPP may overshoot VSS to –2.0V for
periods of up to 20ns. A9 and VPP must not exceed +13.5V at any time.
\7 – Do not exceed 125ºC TC or TJ for plastic package devices.
\8 – Maximum PD, Maximum TJ Are Not to Be Exceeded.
\9 – During transitions, the inputs may undershoot to –2.0 V dc for periods less than 20 ns.
\10 – VPP may be connected directly to VCC except during programming.
\11 – Qualification Only.
\12 – If not tested, shall be guaranteed to the limits specified.
TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS
Test Symbol Conditions
-55ºC TA+125ºC
Unless Otherwise Specified
Min Max Unit
Input Load Current ILI V
IN = 5.5V or 0.0V
All other inputs at either VCC or GND -10.0 +10.0 μA
Output Leakage Current ILO V
OIT = 5.5V or 0.0V -10.0 +10.0 μA
Operating Current, TTL ICC TTL OE (G) = VIL 70ns 65 mA
CE (E) = VIL 90ns 75 mA
V
PP = VCC 120ns 65 mA
O
0-O7 = 0 mA 150ns 60 mA
f = 5 MHz 200ns 30 mA
250ns 30 mA
350ns 25 mA
Operating Current, CMOS ICC CMOS OE (G) = 0 Vdc 70ns 70 mA
CE (E) = 0 Vdc 90ns 60 mA
V
PP = VCC 120ns 55 mA
O
0-O7 = 0 mA 150ns 50 mA
f = 5 MHz 200ns 10 mA
All other inputs 250ns 10 mA
at VCC or GND 350ns 10 mA
Standby Current, TTL ISB TTL OE (G) = VIH 70ns 15 mA
CE (E) = VIH 90ns 2 mA
f = 0 MHz 120ns 2 mA
O
0-O7 = disabled 150ns 2 mA
200ns 1 mA
250ns 1 mA
350ns 1 mA
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 6 of 8
TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS
Test Symbol Conditions
-55ºC TA+125ºC
Unless Otherwise Specified
Min Max Unit
Standby Current, CMOS ISB CMOS OE (G) = VCC 70ns 500 μA
CE (E) = VCC 90ns 200 μA
f = 0 MHz 120ns 200 μA
O
0-O7 = disabled 150ns 200 μA
200ns 140 μA
250ns 140 μA
350ns 140 μA
VPP Read Current IPP V
PP = VCC,
CE (E) = VCC ± 0.2V
100 μA
Input Low Voltage VIL V
PP = VCC 0.8 V
Input High Voltage VIH V
PP = VCC 2.0 V
Output Low Voltage VOL V
IL=0.8V,VIH=2.0V All except 70ns 0.45 V
I
OL= 2.1mA 70ns only 0.40 V
Output High Voltage VOH V
IL=0.8V,VIH=2.0V 2.4 V
I
OL= -400 μA
Output Short Circuit Current IOS V
CC = 5.5V, VOUT =
0.0V
Duration not to exceed 1 second,
one output at a time
100 mA
VPP Read Voltage \10 VPP V
CC - 0.7 VCC V
Input Capacitance \11 CIN V
IN = 0V 10 pF
Output Capacitance \11 COUT V
OUT = 0V 12 pF
Address to Output Delay tACC OE (G) = VIL 70ns 70 ns
CE (E) = VIL 90ns 90 ns
V
PP = VCC 120ns 120 ns
150ns 150 ns
200ns 200 ns
250ns 250 ns
350ns 350 ns
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 7 of 8
TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS
Test Symbol Conditions
-55ºC TA+125ºC
Unless Otherwise Specified
Min Max Unit
CE to Output Delay TCE OE (G) = VIL 70ns 70 ns
V
PP = VCC 90ns 90 ns
120ns 120 ns
150ns 150 ns
200ns 200 ns
250ns 250 ns
350ns 350 ns
OE to Output Delay TOE CE (E) = VIL 70ns 30 ns
V
PP = VCC 90ns 30 ns
120ns 35 ns
150ns 45 ns
200ns 75 ns
250ns 100 ns
350ns 120 ns
OE High to Output Float \12 TDF CE (E) = VIL 70ns 0 25 ns
V
PP = VCC 90ns 0 25 ns
120ns 0 35 ns
150ns 0 40 ns
200ns 0 55 ns
250ns 0 55 ns
350ns 0 105 ns
Output hold from TOH CE (E) = VIL 70ns 10 ns
Addresses, OE or CE OE (G) = VIL 90ns 0 ns
Whichever Occurred First \12 V
PP = VCC 120ns 0 ns
150ns 0 ns
200ns 0 ns
250ns 0 ns
350ns 0 ns
QP27C64
QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 8 of 8
Ordering Information
Part Number Package (Mil-Std-1835) Generic
8510201YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-25/YA
8510201ZA CQCC1-N32 (LCC) QP27C64-25/ZA
8510202YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-35/YA
8510202ZA CQCC1-N32 (LCC) QP27C64-35/ZA
8510203YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-20/YA
8510203ZA CQCC1-N32 (LCC) QP27C64-20/ZA
8510204YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-90/YA
8510204ZA CQCC1-N32 (LCC) QP27C64-90/ZA
8510205YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-12/YA
8510205ZA CQCC1-N32 (LCC) QP27C64-12/ZA
8510206YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-15/YA
8510206ZA CQCC1-N32 (LCC) QP27C64-15/ZA
8510207YA GDIP1-T28 CDIP2-T28 (DIP) QP27C64-70/YA
8510207ZA CQCC1-N32 (LCC) QP27C64-70/ZA
QP Semiconductor supports Source Control Drawing (SCD), and custom package development for this product family.
Notes:
Package outline information and specifications are defined by Mil-Std-1835 package dimension require ments.
“-MIL” products manufactured by QP Semiconductor are compliant to the assembly, burn-in, test and quality conformance
requirements of Test Methods 50 04 & 5005 of Mil-Std-883 for Class B devices. This datasheet defines the electrical test
requirements for the device(s) .
The listed drawings, Mil-PRF-38535, Mil-Std-88 3 and Mil-Std-1835 are available online at http://www.dscc.dla.mil/
Additional information is available at our website http://www.qpsemi.com