CK1V336M10010VR - Samwha Capacitors Group

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

3

2013-3장-수정 2012.11.22 11:22 PM 페이지51 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

52

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

➊Series Name

See page 4.

➋Rated Working Voltage

➌Capacitance

ex) 0.47μF 474

4.7μF 475

47μF 476

470μF 477

4700μF 478

Capacitance Tolerance

➎Case Diameter

ex) Ø4 04

Ø5 05

Ø6.3 6L

Ø8 08

Ø10 10

Ø12.5 12

➏Case Height

ex) 5.3mm 005

5.8mm 006

6.2mm 06B

7.7mm 07K

10mm 010

13.5mm 13M

➐VR (Reel Type)

PART NUMBER SYSTEM

●Part Number System

➊

Series Name

➋

Rated Voltage

➌

Capacitance

➍

Cap. Tol.

➎

Case Diameter

➏

Case Height

➐

Taping Code

➑

Internal Control

Code

WV

Code

4

0G

6.3

0J

10

1A

16

1C

25

1E

35

1V

50

1H

WV

Code

63

1J

100

2A

160

2C

200

2D

250

2E

400

2G

450

2W

Tolerance (%)

Code

±20

M

2013-3장-수정 2012.11.22 11:22 PM 페이지52 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

●Reel (Taping code : VR) ●Polarity ●Recommended Land Size

53

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

●Taping Specifications for Chip Type Capacitors

●Carrier Tape

1

2

X

YZY

Unreel

direction

2.0

23

13±0.5

Ø

80±1.0

A1.5

Ø382

max.

ØD×L A B ØD0E F P0P1P2t1t2W Fig.

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×6.2

8×10

10 ×10

12.5×13.5

4.7

5.7

7.0

8.7

10.7

14.0

4.7

5.7

7.0

8.7

10.7

14.0

1.5

1.75

5.5

7.5

11.5

14.2

4.0

8.0

12.0

16.0

24.0

2.0

0.4

0.5

5.7

6.3

8.2

6.8

11.0

14.0

12.0

16.0

24.0

32.0

ØD×LX Y Z

1.6

2.5

4.0

2.6

3.0

3.5

4.0

3.5

4.0

7.5

1.0

1.4

2.0

3.0

4.0

7.0

ØD×LQ’ty/Reel(pcs.) Q’ty/Box(pcs.)

2000

1000

900

1000

500

200

20000

10000

9000

10000

3000

1000

ØD×LA

14

18

26

34

4×5.3

5×5.3

6.3 ×5.3

6.3 ×5.8

6.3 ×7.7

8×6.2

8×10

10 ×10

12.5×13.5

4×5.3

5×5.3

6.3 ×5.3

6.3 ×5.8

6.3 ×7.7

8×6.2

8×10

10 ×10

12.5×13.5

4×5.3

5×5.3

6.3 ×5.3

6.3 ×5.8

6.3 ×7.7

8×6.2

8×10

10 ×10

12.5×13.5

t2±0.2

t1

B±0.2

W±0.3

F±0.1 E±0.1

P

2

±0.1

ØD

0

+0.1

0

P

0

±0.1

A±0.2

P

1

±0.1

·Fig.1

t2±0.2

t1

B±0.2

W±0.3

F±0.1 E±0.1

P

2

±0.1

ØD

0

+0.1

0

P

0

±0.1

A±0.2 R0.75

0.2

P

1

±0.1

·Fig.2

2013-3장-수정 2012.11.22 11:22 PM 페이지53 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

54

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

Reflow soldering method for the chip aluminum electrolytic capacitor

1. Recommended conditions for reflow soldering

The chip aluminum electrolytic capacitor is subjected to soldering by reflow method.

Temperature and time conditions of reflow soldering shall be set as per each temperature profile shown below

as a standard. The following are recommended conditions in the case of reflow soldering method for the chip

aluminum electrolytic capacitor.

(1) The capacitor shall not be subjected to either flow or dip soldering method.

(2) Avoid soldering twice by reflow. The number of reflow time for chip aluminum electrolytic capacitor shall be once

basically. If this type of capacitor has to be inevitably subjected to the reflow twice, enough cooling time between

the first and the second reflow (at least more than 30 minutes) shall be taken to avoid the consecutive reflows

by all means.

(3) The touch up work with a soldering iron is allowed after the reflow soldering (Temperature of soldering iron : MAX

400°C, Time : 5 sec.), provided that carefully attention shall be paid lest a soldering iron should directly touch the

capacitor body or its resin bottom base.

2. RECOMMENDED REFLOW SOLDERING CONDITIONS

t (25°C to Peak)

Profile Feature

Average Ramp-up Rate (TLto TP)

TSmax to TL -Ramp-up Rate

Peak/classification Temperatrue (TP)

Time within 5°C of actual peak temperature(TP)

Ramp-Down rate

Time 25°C to peak temperature

Time

maintained

above

Temperature Min. (TSmin)

Temperature Max. (TSmax)

Time (TSmin to TSmax)

Time (TL)

Time (tL)

Preheat

Soldering condition

Ø4 ~ Ø10

3°C / second max.

150°C

200°C

60 ~ 150 seconds

3°C / second max.

217°C

60 ~ 90 seconds

250°C

10 seconds max.

3°C / second max.

8minute max.

3°C / second max.

150°C

200°C

40~120 seconds

3°C / second max.

217°C

40 ~ 60 seconds

240°C

10 seconds max.

3°C / second max.

8minute max.

Ø12.5

Temperature



Time



ts

Preheat Ramp

-Down

Critical Zone

TLto TP

Ramp-up

Tsmax

Tsmin

tp

TL

Tp

TL

25

2013-3장-수정 2012.11.22 11:22 PM 페이지54 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

55

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type higher capacitance in larger case size

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, Standard

Series

SC

Solvent Proof

WV

≦100V

Unit : mm

●DRAWING -Series code of SC is “V”

Ø

D×L

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

12.5

×

13.5

W

4.8

5.8

A

2.4

3.3

2.9

3.2

4.6

B

4.3

5.3

6.6

8.3

10.3

12.8

C

4.3

5.3

6.6

8.3

10.3

12.8

E

1.0

1.4

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

0.8~1.4

C±0.2

E±0.2

W±0.2

R

ØD±0.5

0.3 max.

0.4 max.

5.3±0.2

Lot No. ※Voltage

Capacitance

(Ø4, Ø5)

(Ø6.3,Ø8×6.2)

(Ø8×10, Ø10×10)

(Ø12.5)

＋

－

Negative

＋

－

47

6V

Positive

Plastic plateform

B±0.2

※Voltage mark for

6.3V is 6

Series Code



V

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 85°C)

Shelf life(at 85°C)

Resistance to soldering heat

-40 ~ +85°C

WV≦100 I = 0.01CV or 3μA whichever is greater (after 2 minutes)

WV≧160 I = 0.04CV + 100μA(after 1 minutes)

±20% at 120Hz, 20°C

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±20% of initial value (Small size : ±25%)

Less than 200% of the specified value

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

4

6

12

6.3

5

10

4

8

16

3

6

25

2

4

35 ~ 100

2

3

160 ~ 250

3

6

400 ~ 450

6

10

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

4

0.40

6.3

0.35

10

0.24

16

0.20

25

0.16

35

0.15

50

0.12

63

0.12

100

0.12

160

0.20

200

0.20

250

0.20

400

0.25

450

0.25

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지55 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

56

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

SC series

WV

μF4

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

10

22

33

47

100

220

330

470

1000

1500

2200

6.3 10 16 25 35 50

5.3

16

24

29

35

54

68

93

×

4

5

6.3

5.3

5.8

7.7

6.2

21

28

36

34

44

47

62

80

82

173

175

240

290

454

850

960

×

4

5

4

5

6.3

8

5.3

7.7

6.2

10

19

29

30

41

36

48

60

82

91

188

190

265

370

400

480

890

×

4

5

4

5

6.3

8

10

5.3

5.8

7.7

10

13.5

16

21

30

41

43

58

52

69

88

91

162

215

270

307

330

710

870

×

4

5

6.3

5

6.3

8

10

12.5

8×10 8×10

8×6.2

12.5×13.5

10×10

4×5.3

6.3×5.8

4×5.3 4×5.3

8×10

10×10

4×5.3 5.3

5.3

5.8

10

13.5

15

18

24

30

41

53

50

64

70

72

145

232

250

305

400

820

×

4

5

6.3

5

6.3

8

10

12.5

5.3

5.8

7.7

6.2

7.7

10

13.5

11

16

19

27

32

55

65

67

94

105

132

175

265

360

600

3.2

4.7

5.7

6.8

10

15

18

24

25

41

43

71

73

94

95

105

140

181

195

320

600

×

4

5

6.3

8

6.3

8

10

12.5

5.3

5.8

7.7

6.2

7.7

10

×

4

5

6.3

8

6.3

8

10

4×5.3 4×5.3

4×5.3

6.3×5.3

8×10

10×10

12.5×13.5

12.5×13.512.5×13.5

4×5.3

Ripple current (mA rms) at 85°C, 120Hz

Case size ØD X L (mm)

2013-3장-수정 2012.11.22 11:22 PM 페이지56 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

CHIP TYPES

57

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

SC series

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

63 100 160 200 250 400 450

WV

μF

2.2

3.3

4.7

10

22

33

47

68

100

220

31

46

96

117

140

160

370

550

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

29

35

40

77

100

130

155

350

420

10×10

12.5×13.5

100

240

260

10×10

12.5×13.5

100

150

260

10×10

12.5×13.5

100

150

10×10

12.5×13.5

90

115

10×10

12.5×13.5

85

100

115

6.3×5.8

8×6.2

8

×10

10×10

12.5×13.5

Ripple current (mA rms) at 85°C, 120Hz

Case size ØD X L (mm)

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

2013-3장-수정 2012.11.22 11:22 PM 페이지57 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

58

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF6.3 10 16 25 35 50

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

10

22

33

47

100

220

330

470

1000

4×5.3

5×5.3

6.3×5.3

6.3×7.7

8×10

10×10

22

31

36

50

86

105

330

475

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×10

10×10

27

33

46

64

105

305

340

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×10

10×10

17

30

43

51

64

105

340

470

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×10

10×10

13

23

39

48

59

91

340

360

4×5.3

5×5.3

6.3×5.3

6.3×5.8

8×10

10×10

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

10×10

14

24

42

52

63

296

435

2

3

4

5

7

11

13

18

31

45

60

63

295

Ripple current (mA rms) at 105°C, 120Hz

Case size ØD×L(mm)

·Wide operating temperature range of -55 ~ +105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING (See page 55)

-Series code of RC is “F”

Chip type, Wide Temperature Range

Series

RC

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 1000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±25% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.27

10

0.23

16

0.19

25

0.15

35

0.13

50

0.11

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

6.3

3

8

10

3

5

16

2

4

25

2

3

35

2

3

50

2

3

Solvent Proof

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지58 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

59

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type higher capacitance in large case sizes

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, Higher Capacitance Range

Series

JC

Solvent Proof

WV

≦100V

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 105°C)

Shelf life(at 105°C)

Resistance to soldering heat

WV≦100 : -55 ~ +105°C WV≧160 : -40 ~ +105°C

WV≦100 I = 0.01CV or 3μA whichever is greater (after 2 minutes)

WV≧160 I = 0.04CV + 100μA(after 1 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±20% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

4

6

12

6.3

3

8

10

3

5

16

2

4

25 ~ 50

2

3

63 ~ 100

3

4

160 ~ 250

3

6

400 ~ 450

6

10

●DRAWING -Series code of JC is “J” Unit : mm

(Ø6.3,Ø8×6.2)

(Ø8×10, Ø10×10)

(Ø12.5)



J

Ø

D×L

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

12.5

×

13.5

A

2.4

3.3

2.9

3.2

4.6

B

6.6

8.3

10.3

12.8

C

6.6

8.3

10.3

12.8

E

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

0.8~1.4

WV

tanδ

4

0.37

6.3

0.28

10

0.24

16

0.20

25

0.16

35

0.13

50

0.12

63

0.10

100

0.10

160

0.15

200

0.15

250

0.15

400

0.20

450

0.20

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지59 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

60

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

JC series

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

4 6.3 10 16 25 35 50

WV

μF

10

22

33

47

100

220

330

470

680

1000

1500

2200

6.3×5.8 60 6.3×5.8

8×10

10×10

12.5×13.5

60

161

288

340

408

495

560

730

6.3×5.8

8×10

10×10

12.5×13.5

46

60

173

318

351

392

550

650

6.3×5.8

8×10

10×10

12.5×13.5

40

50

148

330

441

489

500

600

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

38

48

79

181

351

372

450

500

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

42

76

124

304

450

500

600

6.3×5.8

8×6.2

8×10

10×10

12.5

×

13.5

30

67

133

180

310

480

63 100 160 200 250 400 450

WV

μF

8×6.2

8×10

10×10

12.5×13.5

8×10

10×10

12.5×13.5

10×10

12.5×13.5

45

85

95

10×10

12.5×13.5

10×10

12.5×13.5

30

65

12.5×13.5

30

12.5×13.5

40

Case size ØD X L (mm)

Ripple current (mA rms) at 105°C, 120Hz

3.3

4.7

10

22

33

47

68

100

32

60

110

130

160

270

90

120

250

300

45

75

85

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

2013-3장-수정 2012.11.22 11:22 PM 페이지60 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

61

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·High Ripple current Compared with JC series

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, High Ripple Current

Series

JH

Solvent Proof

●DRAWING -Series code of JH is “G” Unit : mm

(Ø6.3,Ø8×6.2)

(Ø8×10, Ø10×10)

(Ø12.5)



G

Ø

D×L

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

12.5

×

13.5

A

2.4

3.3

2.9

3.2

4.6

B

6.6

8.3

10.3

12.8

C

6.6

8.3

10.3

12.8

E

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

0.8~1.4

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±20% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.28

10

0.24

16

0.20

25

0.16

35

0.13

50

0.12

63

0.10

100

0.10

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

6.3

3

8

10

3

5

16

2

4

25 ~ 50

2

3

63 ~ 100

3

4

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지61 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

62

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

JH series

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

WV

μF

10

22

33

47

100

220

330

470

680

1000

1500

2200

50 63 100

WV

μF

10

22

33

47

68

100

220

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

45

100

200

270

315

465

720

8×6.2

8×10

10×10

12.5×13.5

48

90

165

195

240

405

8×10

10×10

12.5×13.5

135

180

375

450

6.3×5.8

8×10

10×10

12.5×13.5

90

242

432

510

612

743

840

1095

6.3×5.8

8×10

10×10

12.5×13.5

69

90

260

477

527

588

825

975

6.3×5.8

8×10

10×10

12.5×13.5

60

75

222

495

660

735

750

900

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

57

72

120

270

525

558

675

750

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

63

114

186

456

675

750

900

6.3 10 16 25 35

Case size ØD X L (mm)

Ripple current (mA rms) at 105°C, 120Hz

2013-3장-수정 2012.11.22 11:22 PM 페이지62 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

63

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Long Life Compared with JC series

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, Long Life

Series

JM

Solvent Proof

●DRAWING -Series code of JM is “Q” Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 3000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-25 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.32

10

0.28

16

0.21

25

0.21

35

0.18

50

0.18

63

0.12

100

0.12

WV

Z-25°C/Z+20°C

6.3

8

10

8

16

6

25 ~ 50

4

63 ~ 100

3

NEW

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

Ø

D×L

4×5.3

5×5.3

6.3×5.3

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

12.5

×

13.5

W

4.8

5.8

A

2.4

3.3

2.9

3.2

4.6

B

4.3

5.3

6.6

8.3

10.3

12.8

C

4.3

5.3

6.6

8.3

10.3

12.8

E

1.0

1.4

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

0.8~1.4

C±0.2

E±0.2

W±0.2

R

ØD±0.5

0.3 max.

0.4 max.

5.3±0.2

Lot No. ※Voltage

Capacitance

(Ø4, Ø5)

(Ø6.3,Ø8×6.2)

(Ø8×10, Ø10×10)

(Ø12.5)

＋

－

Negative

＋

－

47

6Q

Positive

Plastic plateform

B±0.2

※Voltage mark for

6.3V is 6

Series Code



Q

2013-3장-수정 2012.11.22 11:22 PM 페이지63 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

64

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

JM series

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

WV

μF

10

22

33

47

100

220

330

470

680

1000

1500

2200

50 63 100

WV

μF

10

22

33

47

68

100

220

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

30

67

133

180

200

310

480

8×6.2

8×10

10×10

12.5×13.5

32

60

110

130

160

270

8×10

10×10

12.5×13.5

90

120

250

300

4×5.3

5×5.3

6.3×5.8

8×10

10×10

12.5×13.5

10

25

35

42

60

161

288

340

408

495

560

730

4×5.3

5×5.3

6.3×5.3

6.3×5.8

8×10

10×10

12.5×13.5

15

30

38

52

60

173

318

351

392

550

650

4×5.3

5×5.3

6.3×5.3

6.3×5.8

8×10

10×10

12.5×13.5

19

33

42

60

148

330

441

489

500

600

5×5.3

6.3×5.3

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

24

38

48

79

181

351

372

450

500

6.3×5.3

6.3×5.8

8×6.2

8×10

10×10

12.5×13.5

26

42

76

124

310

480

500

600

6.3 10 16 25 35

Case size ØD X L (mm)

Ripple current (mA rms) at 105°C, 120Hz

2013-3장-수정 2012.11.22 11:22 PM 페이지64 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

65

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type, long life capacitance in large case sizes

·Chip type with load life of 5000 hours at +105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DRAWING

-Series code of CA is “A”

Chip type, Long Life

Series

CA

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 5000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

6.3 10 16 25 35 50

0.28 0.24 0.2 0.16 0.13 0.12

6.3 10 16 25 35 50

432 22 2

10 7 5 3 3 3

Solvent Proof

WV

μF6.3 10 16 25 35 50

10

22

33

47

100

220

330

470

1000

6.3×5.8

6.3×7.7

8×10

10×10

60

101

160

254

313

6.3×5.8

6.3×7.7

8×10

10×10

46

81

141

238

254

6.3×5.8

6.3×7.7

10×10

40

50

81

216

238

254

6.3×5.8

6.3×7.7

8×10

10×10

38

48

63

116

216

238

6.3×5.8

6.3×7.7

8×10

10×10

6.3×5.8

6.3×7.7

8×10

10×10

42

57

92

151

216

30

120

140

170

310

Ripple current (mA rms) at 105°C, 120Hz

Case size ØD×L(mm)

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

Long Life

Please refer to drawing for CK Series in page 69 for detail drawing.

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지65 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

66

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF4 6.3 10 16 25 35 50

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

6.8

10

15

22

33

47

68

100

4×5.3

5×5.3

24

33

40

48

55

4×5.3

5×5.3

6.3×5.3

25

35

42

55

67

4×5.3

5×5.3

6.3×5.3

22

30

38

52

63

72

4×5.3

5×5.3

6.3×5.3

19

28

33

48

57

4×5.3

5×5.3

6.3×5.3

14

17

24

31

42

4×5.3

5×5.3

6.3×5.3

15

21

26

37

45

4×5.3

5×5.3

6.3×5.3

2

3

4

5

7

11

14

19

26

33

40

Ripple current (mA rms) at 105°C, 120Hz

Case size ØD×L(mm)

·Chip type with load life 5000 hours at 105°C

·Chip type with 5.5mmL Height

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

Chip type,Long Life

Series

CB

●DRAWING (See page 55)

-Series code of CB is “B”

Unit : mm

Item Characteristics

Operating temperature range

Capacitance tolerance

Shelf life(at 105°C)

Resistance to soldering heat

Leakage current max.

Dissipation factor max.

(at 120Hz, 20°C)

Load life

(after application of the rated

voltage for 5000 hours at 105°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

Capacitance change

tanδ

Leakage current

Within ±30% of initial value

Less than 300% of the specified value

Less than specified value

WV

tanδ

4

0.24

6.3

0.22

10

0.19

16

0.16

25

0.14

35

0.12

50

0.11

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

4

2

4

6.3

2

4

10

2

4

16

2

3

25 ~ 50

3

Solvent Proof

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

Long Life

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지66 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

67

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

·Chip type, long life capacitance in large case size

·For ECU

·Application to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DRAWING (See page 55)

-Series code of JL is “P”

Unit : mm

Item Characteristics

Operating temperature range

Leakage current

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 10000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-40 ~ +105°C

I = 0.03CV or 4μA whichever is greater (after 2 minutes)

±20% (20°C, 120Hz)

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of the initial value

Less than 300% of the specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of the initial value

Less than 300% of the specified value

Rated Voltage(V)

tanδ

10

0.32

16

0.24

25

0.21

35

0.18

50

0.18

WV

Z-40°C/Z+20°C

10

12

16

10

25

8

35

6

50

6

WV

μF10 16 25 35 50

33

47

100

220

330

470

8×10

10×10

270

315

8×10

10×10

270

315

8×10

10×10

163

200

304

8×10

10×10

90

132

249

8×10

10×10

75

90

167

Ripple current (mA rms) at 105°C, 120Hz

Case size ØD×L(mm)

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

Chip type, Long Life

Series

JL

Solvent Proof

Long Life

2013-3장-수정 2012.11.22 11:22 PM 페이지67 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

68

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF6.3 10 16 25 35

1.0

1.5

2.2

3.3

4.7

6.8

10

15

22

33

47

68

100

4×5.3

5×5.3

6.3×5.3

5.0

2.6

1.3

50

80

115

5×5.3

6.3×5.3

2.6

1.3

80

115

4×5.3

5×5.3

6.3×5.3

5.0

2.6

1.3

50

80

115

4×5.3

5×5.3

6.3×5.3

5.0

2.6

1.3

50

80

75

115

4×5.3

5×5.3

6.3×5.3

5.0

2.6

1.3

50

80

115

Impedance (Ω) at 20°C, 100kHz

Case size ØD×L(mm)

Ripple current (mA rms) at 105°C, 100kHz

·Chip type, low impedance temperature range up to 105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING (See page 55)

-Series code of ZC is “Z”

Height 5.5mmL, Low Impedance

Series

ZC

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 1000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±20% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.22

10

0.19

16

0.16

25

0.14

35

0.12

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

6.3

2

4

10

2

4

16

2

3

25

2

3

35

3

Solvent Proof

Low Impedance

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.35

120Hz

0.5

300Hz

0.64

1kHz

0.83

10kHz≦

1.00

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지68 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type, low impedance temperature range up to 105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, Low Impedance, High CV

Series

CK

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±25% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.24

10

0.19

16

0.16

25

0.14

35

0.12

50

0.12

63

0.10

80

0.10

100

0.10

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

6.3

2

3

10

2

3

16

2

3

25

2

3

35

2

3

50

2

3

63~100

3

4

Solvent Proof

Low Impedance

Unit : mm

●DRAWING -Series code of CK is “K”

Ø

D×L

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

12.5

×

13.5

A

2.4

3.3

2.9

3.2

4.6

B

6.6

8.3

10.3

12.8

C

6.6

8.3

10.3

12.8

E

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

0.8~1.4

(Ø6.3,Ø8×6.2)

(Ø8×10, Ø10×10)

(Ø12.5×13.5)



K

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

69

2013-3장-수정 2012.11.22 11:22 PM 페이지69 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

WV

μF63

10

22

33

47

68

100

150

220

6.3×5.8

6.3×7.7

8×10

10×10

12.5×13.5

2.3

2.1

0.9

0.45

0.32

80

120

250

400

800

80

6.3×7.7

8×10

10×10

12.5×13.5

2.4

1.3

0.7

0.45

60

130

200

500

100

8×10

10×10

12.5×13.5

1.3

0.7

0.45

130

200

500

70

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF

10

15

22

33

47

68

100

150

220

330

470

680

1000

1500

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.44

0.34

0.26

0.17

0.09

230

280

300

450

670

Ripple current (mA rms) at 105°C, 100kHz

Impedance (Ω) at 20°C, 100kHz

Case size ØD X L (mm)

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

CK series

6.3 10 16 25 35 50

0.44

0.34

0.26

0.17

0.09

230

280

300

450

670

6.3×5.8

6.3×7.7

8×6.2

6.3×7.7

8×6.2

8×10

10×10

0.44

0.34

0.26

0.34

0.26

0.17

0.09

230

280

300

280

300

450

670

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.44

0.34

0.26

0.17

0.09

230

280

300

450

670

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.44

0.34

0.26

0.17

0.09

230

280

300

450

670

6.3×5.8

6.3×7.7

8×6.2

6.3×7.7

8×6.2

8×10

10×10

0.88

0.68

0.63

0.68

0.63

0.34

0.18

165

280

300

280

300

450

670

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.35

120Hz

0.5

300Hz

0.64

1kHz

0.83

10kHz≦

1.00

2013-3장-수정 2012.11.22 11:22 PM 페이지70 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

71

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type, low impedance temperature range up to 105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

Chip type, Extremely Low Impedance

Series

CD

●DRAWING

-Series code of CD is “D”

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±25% of initial value

Less than 200% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.24

10

0.19

16

0.16

25

0.14

35

0.12

50

0.12

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

6.3

2

3

10

2

3

16

2

3

25

2

3

35

2

3

50

2

3

Solvent Proof

Low Impedance



D



D

(Ø6.3×5.8, 7.7, Ø8×6.2)

(Ø8×10, Ø10×10)

Ø

D

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

A

2.4

3.3

2.9

3.2

B

6.6

8.3

10.3

C

6.6

8.3

10.3

E

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지71 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

72

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF

10

15

22

33

47

68

100

150

220

330

470

680

1000

1500

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

Impedance (Ω) at 20°C, 100kHz

Case size ØD X L (mm)

Ripple current (mA rms) at 105°C, 100kHz

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

CD series

6.3 10 16 25 35 50

0.39

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.39

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.39

0.36

0.32

0.26

0.16

0.10

240

290

300

600

850

6.3×5.8

6.3×7.7

8×10

10×10

0.39

0.32

0.16

0.08

240

290

600

850

6.3×5.8

6.3×7.7

8×6.2

6.3×7.7

8×6.2

8×10

10×10

0.86

0.66

0.63

0.66

0.63

0.32

0.16

170

280

300

280

300

350

700

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.35

120Hz

0.5

300Hz

0.64

1kHz

0.83

10kHz≦

1.00

2013-3장-수정 2012.11.22 11:22 PM 페이지72 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

73

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

Unit : mm

·Chip type, low impedance temperature range up to 105°C

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DRAWING

-Series code of CM is “M”

Chip type, Extremely Low Impedance

Long Life Series

CM

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 5000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.01CV or 3μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 250% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.26

10

0.19

16

0.16

25

0.14

35

0.13

50

0.12

WV

Z-25°C/Z+20°C

Z-55°C/Z+20°C

6.3

2

4

10

2

4

16

2

4

25

2

3

35

2

3

50

2

3

Solvent Proof

Low Impedance



M



M

(Ø6.3×5.8, 7.7, Ø8×6.2)

(Ø8×10, Ø10×10)

Ø

D

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

A

2.4

3.3

2.9

3.2

B

6.6

8.3

10.3

C

6.6

8.3

10.3

E

2.2

2.3

3.1

4.5

R

0.5~0.8

0.8~1.1

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

ØD

Life time

ØD ≦6.3, Ø8×6.2mmL

3000 hours

ØD ≧8

5000 hours

2013-3장-수정 2012.11.22 11:22 PM 페이지73 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

74

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF

10

15

22

33

47

68

100

150

220

330

470

680

1000

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

Impedance (Ω) at 20°C, 100kHz

Case size ØD X L (mm)

Ripple current (mA rms) at 105°C, 100kHz

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

CM series

6.3 10 16 25 35 50

0.39

0.36

0.26

0.16

0.08

240

290

300

600

850

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.39

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

0.39

0.36

0.32

0.26

0.16

0.08

240

290

300

600

850

6.3×5.8

6.3×7.7

8×10

10×10

0.39

0.32

0.16

0.08

240

290

600

850

6.3×5.8

6.3×7.7

8×6.2

6.3×7.7

8×6.2

8×10

10×10

0.86

0.66

0.63

0.66

0.63

0.32

0.16

170

280

300

280

300

350

700

6.3×5.8

6.3×7.7

8×6.2

8×10

10×10

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.35

120Hz

0.5

300Hz

0.64

1kHz

0.83

10kHz≦

1.00

2013-3장-수정 2012.11.22 11:22 PM 페이지74 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

75

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

·Chip type, high temperature range, for +125°C use

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DRAWING (See page 59)

-Series code of UC is “U”

Chip type, High Reliability

Series

UC

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 125°C)

Shelf life (at 125°C)

Resistance to soldering heat

-40 ~ 125°C

I = 0.03CV or 4μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of specified value

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

10

0.32

16

0.24

25

0.21

35~50

0.18

63~100

0.12

160~200

0.2

250~400

0.24

Solvent Proof

WV≦100V

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

WV

μF10 16 25 35 50 63

10

22

33

47

68

100

220

330

470

1000

8×6.2

8×10

10×10

12.5×13.5

65

125

200

525

8×6.2

8×10

10×10

12.5×13.5

65

125

200

525

8×6.2

8×10

10×10

12.5×13.5

65

125

200

525

8×6.2

8×10

10×10

12.5×13.5

65

125

200

525

8×6.2

8×10

10×10

12.5×13.5

65

125

200

525

8×6.2

8×10

10×10

12.5×13.5

40

67

115

335

Ripple current (mA rms) at 125°C, 120Hz

Case size ØD×L(mm)

WV

μF80 100 160 200 250 400

3.3

4.7

10

22

33

47

68

8×10

10×10

12.5×13.5

45

80

300

8×10

10×10

12.5×13.5

45

80

300

10×10

12.5×13.5

45

85

10×10

12.5×13.5

45

85

12.5×13.5

45

85

12.5×13.5

30

Ripple current (mA rms) at 125°C, 120Hz

Case size ØD×L(mm)

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

Upgrade

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

10

8

12

16

6

8

25

4

6

35~50

4

63~100

3

4

160~200

3

6

250~400

6

10

2013-3장-수정 2012.11.22 11:22 PM 페이지75 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

76

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

Solvent Proof

WV

μF10 16 25 35 50

22

33

47

68

100

220

330

470

1000

8×6.2

8×10

10×10

12.5×13.5

48

90

125

150

405

8×6.2

8×10

10×10

12.5×13.5

50

66

163

200

304

8×6.2

10×10

12.5×13.5

45

163

200

304

8×6.2

10×10

12.5×13.5

41

90

105

132

249

8×6.2

8×10

10×10

12.5×13.5

28

75

90

132

167

Ripple current (mA rms) at 130°C, 120Hz

Case size ØD×L(mm)

·Chip type, high temperature range, for + 130°C use

·For ECU

·Application to automatic insertion machine using carrier

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING (See page 59)

-Series code of CF is “H”

Chip type, High Temperature, Long Life,

Series

Unit : mm

Item Characteristics

Operating temperature range

Shelf life (at 130°C)

Resistance to soldering heat

Leakage current

Capacitance tolerance

-40 ~ +130°C

I = 0.03CV or 4μA whichever is greater (after 2 minutes)

±20% (20°C,120Hz)

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 5000 hours at 130°C)

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of the specified value

Rated Voltage(V)

tanδ

10

0.32

16

0.24

25

0.21

35

0.18

50

0.18

WV

Z-40°C/Z+20°C

10

12

16

11

25

8

35

6

50

6

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

CF

Long Life

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

ØD

Life time

Ø8×6.2mmL

2000 hours

Ø8×10mmL

3000 hours

ØD ≧10

5000 hours

2013-3장-수정 2012.11.22 11:22 PM 페이지76 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

77

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

Solvent Proof

WV

μF10 16 25 35 50

33

47

68

100

220

330

470

8×10

10×10

0.6

0.5

270

315

8×10

10×10

12.5×13.5

270

315

345

0.6

0.5

0.4

8×10

10×10

12.5×13.5

0.6

0.5

0.4

270

315

345

8×10

10×10

12.5×13.5

0.6

0.5

0.4

270

315

345

8×10

10×10

12.5×13.5

0.6

0.5

0.4

270

315

345

Ripple current (mA rms) at 130°C, 100kHz

Impedance (Ω) at 20°C, 100kHz

Case size ØD×L(mm)

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

Unit : mm

·Chip type, Low Impedance temperature range up to 130°C use

·For ECU

·Application to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DRAWING (See page 59)

-Series code of CT is “C”

Chip type, High Temperature, Low Imp.,

Series

CT

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 130°C)

Shelf life (at 130°C)

Resistance to soldering heat

-40 ~ +130°C

I = 0.03CV or 4μA whichever is greater (after 2 minutes)

±20% ( 20°C, 120Hz)

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage Current

Capacitance Change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of specified value

Leakage Current

Capacitance Change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.35

120Hz

0.5

300Hz

0.64

1kHz

0.83

10kHz≦

1.00

Low Impedance

Rated Voltage(V)

tanδ

10

0.32

16

0.24

25

0.21

35

0.18

50

0.18

WV

Z-40°C/Z+20°C

10

12

16

10

25

8

35

6

50

6

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지77 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

78

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF10 16 25 35 50

33

47

68

100

220

330

470

1000

10×10

12.5×13.5

183

218

405

10×10

12.5×13.5

163

200

304

10×10

12.5×13.5

160

200

304

10×10

12.5×13.5

90

105

132

249

10×10

12.5×13.5

75

90

132

167

Ripple current (mA rms) at 150°C, 120Hz

Case size ØD×L(mm)

·Chip type, high temperature range, for + 150°C use

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING (See page 59)

-Series code of CW is “W”

Chip type, High Reliability

Series

CW

Unit : mm

Item Characteristics

Operating temperature range

Shelf life (at 150°C)

Resistance to soldering heat

Leakage current

Capacitance tolerance

-40 ~ +150°C

I = 0.03CV or 4μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 1000 hours at 150°C)

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±30% of initial value

Less than 300% of the specified value

WV

tanδ

10

0.30

16

0.20

25

0.16

35

0.14

50

0.14

WV

Z-40°C/Z+20°C

10

12

16

10

25

8

35

6

50

6

Solvent Proof

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

●FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

Coefficient

50Hz

0.70

120Hz

1.00

300Hz

1.17

1kHz

1.36

10kHz≦

1.50

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지78 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

79

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

CHIP TYPES

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING

-Series code of NC is “N”

·Chip type with 5.5mmL height

·Designed for surface mounting on high density PC board

·Applicable to automatic mounting machine using carrier tape

·Complied to the RoHS directive

Chip type, Non-polarized

Series

NC

Unit : mm

Solvent Proof

Non-polarized

50

0.15

-40 ~ +85°C

I = 0.05CV or 10μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Test method

Less than specified value

Within ±20% of initial value

Less than 200% of specified value

Polarity reverse each 250 hours

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.24

10

0.20

16

0.17

25

0.17

35

0.15

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

6.3

4

8

10

3

6

16

2

4

25

2

4

35

2

3

50

2

3

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 2000 hours at 85°C)

Shelf life (at 85°C)

Resistance to soldering heat

WV

μF6.3 10 16 25 35 50

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

10

22

33

47

5×5.3

6.3×5.3

28

37

45

4×5.3

6.3×5.3

17

33

41

4×5.3

5×5.3

6.3×5.3

12

23

37

49

5×5.3

6.3×5.3

12

16

27

4×5.3

5×5.3

6.3×5.3

8.4

16

18

29

4×5.3

5×5.3

6.3×5.3

1.0

2.0

2.8

4.0

8.4

13

17

20

Ripple current (mA rms) at 85°C, 120Hz

Case size ØD X L (mm)

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

ØD

4

5

6.3

B

4.3

5.3

6.6

W

4.8

5.8

7.1

C

4.3

5.3

6.6

E

1.0

1.4

2.2

C±0.2

E±0.2

W±0.2

0.5~0.8

ØD±0.5

0.3 max.

0.4 max.

5.3±0.2

Plastic plateform

B±0.2

※Voltage mark for

6.3V is 6

Lot No.

Series Code

Capacitance

47

6N

※Voltage

2013-3장-수정 2012.11.22 11:22 PM 페이지79 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T

80

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

WV

μF6.3 10 16 25 35 50

0.1

0.22

0.33

0.47

1.0

2.2

3.3

4.7

10

22

33

47

5×5.3

6.3×5.3

28

37

45

4×5.3

6.3×5.3

17

33

41

4×5.3

5×5.3

6.3×5.3

12

23

37

49

5×5.3

6.3×5.3

12

16

27

4×5.3

5×5.3

6.3×5.3

4×5.3

5×5.3

6.3×5.3

8.4

16

18

29

1.3

2.3

2.8

4.0

8.4

13

17

20

Ripple current (mA rms) at 105°C, 120Hz

Case size ØD×L(mm)

·Chip type, Non-polarized, Wide temperature 105°C

·Chip type with 5.5mmL height

·Designed for surface mounting on high density PC board

·Applicable to automatic insertion machine using carrier tape

·Complied to the RoHS directive

●DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

●DRAWING (See page 79)

-Series code of CN is “C”

Height 5.5mmL, 105

°C

Non-polarized

Series

CN

Unit : mm

Item Characteristics

Operating temperature range

Leakage current max.

Capacitance tolerance

Dissipation factor max.

(at 120Hz, 20°C)

Low temperature characteristics

(Impedance ratio at 120Hz)

Load life

(after application of the rated

voltage for 1000 hours at 105°C)

Shelf life (at 105°C)

Resistance to soldering heat

-55 ~ +105°C

I = 0.05CV or 10μA whichever is greater (after 2 minutes)

±20% at 120Hz, 20°C

The following specifications shall be satisfied when the capacitors are restored to 20°C

after exposing them at 250°C for 10 seconds.

Leakage current

Capacitance change

tanδ

Less than specified value

Within ±10% of initial value

Less than specified value

WV

tanδ

6.3

0.32

10

0.26

16

0.24

25

0.20

35

0.18

50

0.18

WV

Z-25°C/Z+20°C

Z-40°C/Z+20°C

6.3

4

8

10

3

6

16

2

4

25

2

4

35

2

3

50

2

3

Solvent Proof

Non-polarized

Leakage current

Capacitance change

tanδ

Test method

Less than specified value

Within ±20% of initial value

Less than 200% of specified value

Polarity reverse each 250 hours

After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.

The measurement shall be performed at 20°C by the KS C 6035 clause 5.4.

2013-3장-수정 2012.11.22 11:22 PM 페이지80 G4-1.25G(Mac 1) JETPDF 2400DPI 175LPI T